ISO Standards ir Cylinder: Standard Double cting with End of Stroke Cushioning Series CP ø, ø, ø, ø, ø, ø0, ø With au switch 0 CPS 0 J W CPSD With au switch (uilt-in magnet) L F G C Mounting asic xial foot Rod flange ead flange Single clevis Double clevis D Mounting brackets are shipped gether, (but not assembled). mm mm mm mm mm 0 mm mm Nil J JJ K KK ow order 0 J W MW Cylinder stroke Refer Standard Strokes on page. Rod boot Without rod boot Nylon tarpaulin (one side) Nylon tarpaulin (both sides) eat resistant tarpaulin (one side) eat resistant tarpaulin (both sides) Rod Nil W Single rod Double rod S Made Order Refer page for details. Number of au switches Nil 2 pcs. S pc. 3 3 pcs. n n pcs. u switch Nil Without au switch For applicable au switches, refer the table below. Series C Series CP Series C pplicable u Switches/Refer the est Pneumatics No. 2 for further information on au switches. Type Solid state au switch Reed au switch Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) Electrical entry Grommet Grommet Indicar light Yes Wiring (Output) 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN equivalent) Since there are other applicable au switches than listed above, refer the est Pneumatics No. 2 for details. For details about au switches with pre-wired connecr, refer the est Pneumatics No. 2. The D-/M/MW/M au switches are shipped gether, (but not assembled). (owever, only the au switch mounting brackets are assembled before shipment.) Note) D-Y, Y, YP, YW, Z, Z type cannot be mounted on the CP series. Moreover, the D-M and au switches cannot be mounted on square groove of the CP series. 2 V DC Load voltage V, V V V, V V V, V V u switch model MN MP M MNW MPW MW MN MP M Lead wire length (m) Pre-wired connecr pplicable load V IC Yes Grommet 0 V 3 Relay, 2-wire 2 V V No 0 V or less 0 IC PLC Water resistant type au switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Lead wire length symbols: 0. m Nil (Example) MNW m M (Example) MNWM Solid state switches marked with are produced upon receipt of order. 3 m L (Example) MNWL m Z (Example) MNWZ C 0. (Nil) (M) 3 (L) (Z) IC IC IC Relay, PLC Series C 3
Series CP Specifications ction Fluid Proof pressure Max. operating pressure Min. operating pressure mbient and fluid temperature Lubrication Operating pisn speed llowable stroke lerance Cushion Port size Mounting 0 Double acting ir. MPa.0 MPa 0.0 MPa Without au switch: 0 C (No freezing) With au switch : C (No freezing) Not required (Non-lube) 00 mm/s 00 mm/s +.0 0 +. 0 +. 0 Up 2 st:, 00 st:, 0 st:, 00 st: ir cushion G / G / G / G 3/ G 3/ G /2 G /2 asic, xial foot, Rod flange, ead flange, Single clevis, Double clevis, Center trunnion +2.2 0 Standard Strokes Minimum Stroke for u Switch Mounting Refer Minimum Stroke for u Switch Mounting on page. Made Order (For details, refer pages.) Symbol Specifications -X Change of rod end shape -X eat resistant cylinder ( C) -XC With heavy duty scraper Tie-rod, cushion valve, tie-rod nut, etc. -XC made of stainless steel -XC Dual stroke cylinder/double rod type -XC Dual stroke cylinder/single rod type -XC Fluororubber seal -XC3 With coil scraper Made of stainless steel -XC (with hard chrome plated pisn rod) 0 Standard stroke,,, 0,, 0, 0, 2, 0, 0, 0,,, 0,, 0, 0, 2, 0, 0, 0,,, 0,, 0, 0, 2, 0, 0, 0, 0,,, 0,, 0, 0, 2, 0, 0, 0, 0,,, 0,, 0, 0, 2, 0, 0, 0, 0, 00, 0,,, 0,, 0, 0, 2, 0, 0, 0, 0, 00, 0 Intermediate strokes are available. Note) Please consult with SMC for longer strokes. ccessories Standard Option Mounting asic Foot Rod end nut Clevis pin Pisn rod ball joint Rod clevis Rod boot Rod flange ead flange Single clevis Double clevis Do not use a pisn rod ball joint (or floating joint) gether with a single clevis with a ball joint (or clevis pivot bracket with a ball joint). Max. stroke Note) 00 00 00 00 00 00 00 Center trunnion Caution e sure read before handling. Refer page for Safety Instructions and andling Precautions for SMC Products (M-E03-3) for ctuar and u Switch Precautions.
ISO Standards ir Cylinder: Standard Type Double cting with End of Stroke Cushioning Series CP Theoretical Output ore size 0 Rod size Operating direction OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN Pisn area (mm 2 ) 3 2 3 Note) Theoretical output (N) = Pressure (MPa) x Pisn area (mm 2 ) Weights (Single rod) asic Foot Flange asic weight Single clevis Double clevis Trunnion dditional weight per mm of stroke ll mounting brackets Single clevis 0.0 0. ccessories Double clevis 0.0 0. Calculation: Example) CPSD-0 asic weight 0. (kg) (asic, ø) dditional weight 0. (kg/ st) Cylinder stroke 0 (st) Mounting bracket weight 0. (kg) (Double clevis) 0. + 0. x 0 + 0. =.2 kg OUT Operating pressure (MPa) 0.2 0.3 0. 0. 0. 0. 0. 0..0 2 2 2 2 2 3 2 3 3 3 2 0 3 2 3 2 3 33 2 3 0 3 3 3 0 22 2 2 3 2 2 2 0 3 2 2 0 2 3 2 2 2 3 32 23 0 3 2 2 2 0 2 3 2 0 3 0 3 3 2 0. 0. 0. 0. 0. 0. 0. 0... 2. 0. 0.3 0. 0. 0. 0. 0.. 0. 0.3 0..0 0. 0. 0..2..3 2.. 0. 0. 0. 0.3 0. 0. 0. 0. IN (N) (kg) 0 3..2.0 2....3. 2... 2. 0. 0... llowable Kinetic Energy Load mass (kg) 000 0 ø ø ø ø ø0 ø ø 0 00 000 Maximum speed (mm/s) (Example) Find the upper limit of rod end load when an air cylinder of ø is operated at 0 mm/s. From a point indicating 0 mm/s on the axis of abscissas, extend a line upward and find a point where it intersects with a line for the mm bore size. Extend a line from the intersection the left and find a load mass kg. Series C Series CP Series C Series C
Series CP Construction @!!3!0!!2 q! e r @2 y t! @3! @0 w i u ø ø ø!! ø ø (No flat washer for ø) i o Component Parts No. Description Material Note 2 3 3 2 Rod cover ead cover Cylinder tube Pisn rod Pisn Cushion ring Tie-rod Tie-rod nut Flat washer Rod end nut Cushion valve ushing Retaining ring Rod seal holder Retaining ring Cushion seal Wear ring Pisn seal Rod seal Cylinder tube gasket Cushion valve seal Pisn gasket Magnet luminum die-cast luminum die-cast luminum alloy Carbon steel luminum alloy luminum alloy Carbon steel Steel Steel Steel Steel wire earing alloy Steel for spring Stainless steel Steel for spring Urethane rubber Resin NR NR NR NR NR ø, ø0 ø ø ø ø Replacement Parts/Seal Kit (Single rod) 0 Seal Kit (Double rod) 0 Kit no. CS- CS- CS- CS- CS- CS-0 CS- Kit no. CSW- CSW- CSW- CSW- CSW- CSW-0 CSW- Contents Kits include items! @0. Seal kits consist of items! @0, and can be ordered by using the seal kit number corresponding each bore size. The seal kit includes a grease pack ( g for ø ø, g for ø and ø, g for ø0 and ø). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S0 ( g), GR-S-0 ( g) Contents Kits include items! and! @0. Seal kits consist of items! and! @0, and can be ordered by using the seal kit number corresponding each bore size. The seal kit includes a grease pack ( g for ø ø, g for ø and ø, g for ø0 and ø). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S0 ( g), GR-S-0 ( g)
ISO Standards ir Cylinder: Standard Type Double cting with End of Stroke Cushioning Series CP Dimensions asic: CPS(D) Stroke SW KK PL 2 x EE PL ød W W Series C øe E R ø ød ø R E L VD W L2 L x RT Cushion valve G G L + Stroke ZZ + Stroke G V Series CP With rod boot l f h h + L + V + Stroke Series C 0 0 Stroke range Without rod boot With rod boot Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 ø ød d EE PL RT L KK SW G G L VD V W W W ZZ E R 2 3 G / G / G / G 3/ G 3/ 3.. M x M x M x. M x. M x.. M x. M x. M x. M x. M x. 3 3. 3... 2 3 3 3 2. 3.. 2 G /2 M x. M x. 3 3 G /2 M x. 3 M2 x 2 2 0 2 l h L2 L ød øe f 0 0 0 0 0 0 0 0 0 0 00 0 00 00 0 0 0 0 0 0 00 0 00 00.. 3. 3. 0 0 2 2 0 0 2 2 0 3 3 3 23 2 2 33 0 3 3 3 23 2 2 33 2 2.. 3. 3. 0 0 2 2 0 0 2 2 0 0 2 2 2 0 0 0 2 2 2 0 2.. 3. 3. 0 0 2 2 3 2 2 2 2 3 3 0 0 2 2 3 2 2 2 2 3 3 0 0 0 0 0 2 2 2 2 0 0 Series C
Series CP Dimensions asic: CPS(D) Stroke W SW PL 2 x EE PL KK SW KK l f h h + L + + 2 x Stroke ød øe øe ød ød øe ø ød W W ød ø L VD L2 L G W G x RT Cushion valve L + Stroke ZY + 2 x Stroke VD L2 L G W + Stroke + Stroke With rod boot at one end With rod boot at both ends h l f L + Stroke 2 x h + L + 2 x Stroke f l + Stroke h + Stroke 0 Stroke range Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 ø ød d EE PL RT L KK SW G G L VD W W W ZY 2 3 G / G / G / G 3/ G 3/ G /2 G /2 3.. M x M x M x. M x. M x. M x. M x.. 3 M x. M x. M x. M x. M x. M x. M2 x 2 3 2 3. 3. 3 0.. 2 3 3 0 23 2 0 0 3 L2 2 2 L 0 ød øe f 2 l h 0 0 0 0 0 0 0 0 0 0 00 0 00 00 0 0 0 0 0 0 00 0 00 00.. 3. 3. 0 0 2 2 0 0 2 2 0 3 3 3 23 2 2 33 0 3 3 3 23 2 2 33.. 3. 3. 0 0 2 2 0 0 2 2 0 0 2 2 2 0 0 0 2 2 2 0.. 3. 3. 0 0 2 2 3 2 2 2 2 3 3 0 0 2 2 3 2 2 2 2 3 3 0 0 0 0 0 2 2 2 2 0 0
ISO Standards ir Cylinder: Standard Type Double cting with End of Stroke Cushioning Series CP Dimensions xial foot (L) X + Stroke x ø Series C TR E T O S + Stroke O Rod flange (F) x F E2 R Series CP TF UF W MF ead flange (G) ZF + Stroke MF Series C CD Single clevis (C) Double clevis (D) XD + Stroke L MR EW C U E Series C 0 E 0 Max. TR O 0 0 Max. T....... U C CD S X R TF F E2 UF W MF ZF EW L MR XD h 0 2 2 2 3 0 2 2 20 0 2 0 0 0 0 Max. 0 3 Max. 3 0 0 2 0 0 2 2 0 2 2 0 0. 0. 0. 0. 0. 0. 0..2 Min.. Max. 2 0 0 0 2 2 2 E 0 Max.
ISO Standards ir Cylinder: Standard Type Double cting, Single/Double Rod Series C ø, ø, ø, ø, ø, ø0, ø With au switch L F G C D T pplicable u Switches/Refer the est Pneumatics No. 2 for further information on au switches. Type Solid state au switch Reed au switch Mounting asic xial foot Rod flange ead flange Single clevis Double clevis Center trunnion Mounting brackets except center trunnion type are shipped gether, (but not assembled). Wiring (Output) Tie-rod mounting MN MP M J MNW MPW MW MN MP M FF and mounting Water resistant type au switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Lead wire length symbols: 0. m Nil (Example) MNW m M (Example) MNWM Solid state au switches marked with are produced upon receipt of order. 3 m L (Example) MNWL m Z (Example) MNWZ PDW Since there are other applicable au switches than listed above, refer the est Pneumatics No. 2 for details. For details about au switches with pre-wired connecr, refer the est Pneumatics No. 2. The D-/M/MW/M au switches are shipped gether, (but not assembled). (owever, only the au switch mounting brackets are assembled before shipment.) Special function Diagnostic indication (2-color indication) Water resistant (2-color indication) With diagnostic output (2-color indication) Magnetic field resistant (2-color indication) Diagnostic indication (2-color indication) CS 0 J W CSD With au switch (uilt-in magnet) mm mm mm mm mm 0 0 mm mm Electrical entry Grommet Terminal conduit Grommet Grommet Terminal conduit DIN Grommet Indicar light Yes Yes No Yes No Yes 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire -wire (NPN) 2-wire (Non-polar) 3-wire (NPN Equivalent) 2-wire 2 V 2 V 2 V ow Order 0 J W MW Cylinder stroke Refer Standard Strokes on page. DC Load voltage V, V V V, V V V, V V V, V V V, V V V C 0 V, 0 V 0 V 0 V or less 0 V, 0 V 0 V or less 0 V, 0 V Rod Nil W u switch model 3 0 W Single rod Double rod Rod boot Nil Without rod boot J Nylon tarpaulin (one side) JJ Nylon tarpaulin (both sides) K eat resistant tarpaulin (one side) KK eat resistant tarpaulin (both sides) G3 K3 33 3 Lead wire length (m) 0. (Nil) (M) 3 (L) S Number of au switches Nil 2 pcs. S pc. 3 3 pcs. n n pcs. (Z) Made Order Refer page for details. u switch Nil Without au switch For applicable au switches, refer the table below. Pre-wired connecr pplicable load IC IC IC IC IC IC IC Relay, PLC Relay, PLC PLC Relay, PLC
ISO Standards ir Cylinder: Standard Type Double cting, Single/Double Rod Series C Specifications Minimum Stroke for u Switch Mounting Refer Minimum Stroke for u Switch Mounting on page 2. Made Order (For details, refer pages.) Symbol Specifications -X Change of rod end shape -XC Change of trunnion bracket mounting position -X eat resistant cylinder ( C) -X Cold resistant cylinder -XC With heavy duty scraper Tie-rod, cushion valve, tie-rod nut, etc. -XC made of stainless steel -XC Dual stroke cylinder/double rod type -XC Dual stroke cylinder/single rod type -XC Fluororubber seal -XC3 With coil scraper Made of stainless steel -XC (with hard chrome plated pisn rod) ction Fluid Proof pressure Max. operating pressure Min. operating pressure mbient and fluid temperature Lubrication Operating pisn speed llowable stroke lerance Cushion Port size Mounting Standard Strokes 0 0 Double acting ir. MPa.0 MPa 0.0 MPa Without au switch: 0 C (No freezing) With au switch: C (No freezing) Not required (Non-lube) 00 mm/s 00 mm/s Standard stroke,,, 0,, 0, 0, 2, 0, 0, 0,,, 0,, 0, 0, 2, 0, 0, 0,,, 0,, 0, 0, 2, 0, 0, 0, 0,,, 0,, 0, 0, 2, 0, 0, 0, 0,,, 0,, 0, 0, 2, 0, 0, 0, 0, 00, 0,,, 0,, 0, 0, 2, 0, 0, 0, 0, 00, 0 Intermediate strokes are available. Note) Please consult with SMC for longer strokes. ccessories Standard Option Mounting asic Foot Rod end nut Clevis pin Pisn rod ball joint Rod clevis Rod boot Up 2 st: 0, 00 st: 0, 0 st: 0, 00 st: ir cushion G / G / G / G 3/ G 3/ G /2 G /2 asic, xial foot, Rod flange, ead flange, Single clevis, Double clevis, Center trunnion +.0 Rod flange ead flange Single clevis Double clevis Do not use a pisn rod ball joint (or floating joint) gether with a single clevis with a ball joint (or clevis pivot bracket with a ball joint). +. +. +2.2 0 Max. stroke Note) 00 00 00 00 00 00 00 Center trunnion Series C Series C Series CP Series C Caution e sure read before handling. Refer page for Safety Instructions and andling Precautions for SMC Products (M-E03-3) for ctuar and u Switch Precautions.
Series C Theoretical Output ore Pisn Rod size Operating Operating pressure (MPa) size area direction (mm 2 ) 0.2 0.3 0. 0. 0. 0. 0. 0..0 0 OUT OUT OUT OUT OUT OUT OUT 3 2 33 0 2 3 3 2 2 2 3 3 0 2 2 2 32 2 0 3 3 22 3 0 0 0 2 23 2 3 2 2 0 3 2 IN IN IN IN IN IN IN 3 3 2 3 0 3 3 2 3 2 2 2 2 3 2 2 3 2 3 2 3 3 2 2 0 2 2 3 Note) Theoretical output (N) = Pressure (MPa) x Pisn area (mm 2 ) OUT IN (N) llowable Kinetic Energy Load mass (kg) 000 0 ø ø ø ø ø0 ø ø Weights (Single rod) asic Foot Flange asic weight Single clevis Double clevis Trunnion dditional weight per mm of stroke ll mounting brackets 0.3 0. 0. 0. 0. 0. 0. 0.3.33. 2. 0. 0.3 0. 0. 0. 0. 0.. 0. 0.3 0..0 0. 0. 0..2..3 2.. 0. 0.2 0.2 0. (kg) 0 3..0.0 2....3. 2... 2. 0. 0. 0 00 000 Maximum speed (mm/s) (Example) Find the upper limit of rod end load when an air cylinder of ø is operated at 0 mm/s. From a point indicating 0 mm/s on the axis of abscissas, extend a line upward and find a point where it intersects with a line for the mm bore size. Extend a line from the intersection the left and find a load mass kg. Single clevis 0.0 0. ccessories Double clevis 0.0 0. Calculation: Example) CSD-0 asic weight 0.3 (kg) (asic, ø) dditional weight 0. (kg/ st) Cylinder stroke 0 (st) Mounting bracket weight 0. (kg) (Double clevis) 0.3 + 0. x 0 + 0. =. kg 0. 0.3 0. 0...
ISO Standards ir Cylinder: Standard Type Double cting, Single/Double Rod Series C Construction @!!3!0!!2 q! e r @2 y t! @3! @0 w Series C i u ø ø ø!! ø ø (No flat washer for ø) Series CP i o Component Parts No. Description Material Note 2 3 3 2 Rod cover ead cover Cylinder tube Pisn rod Pisn Cushion ring Tie-rod Tie-rod nut Flat washer Rod end nut Cushion valve ushing Retaining ring Rod seal holder Retaining ring Cushion seal Wear ring Pisn seal Rod seal Cylinder tube gasket Cushion valve seal Pisn gasket Magnet luminum die-cast luminum die-cast luminum alloy Carbon steel luminum alloy luminum alloy Carbon steel Steel Steel Steel Steel wire earing alloy Steel for spring Stainless steel Steel for spring Urethane rubber Resin NR NR NR NR NR ø, ø0 ø ø ø ø Replacement Parts/Seal Kit (Single rod) 0 Seal Kit (Double rod) 0 Kit no. CS- CS- CS- CS- CS- CS-0 CS- Kit no. CSW- CSW- CSW- CSW- CSW- CSW-0 CSW- Contents Kits include items! @0. Seal kits consist of items! @0, and can be ordered by using the seal kit number corresponding each bore size. The seal kit includes a grease pack ( g for ø ø, g for ø and ø, g for ø0 and ø). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S0 ( g), GR-S-0 ( g) Contents Kits include items! and! @0. Seal kits consist of items! and! @0, and can be ordered by using the seal kit number corresponding each bore size. The seal kit includes a grease pack ( g for ø ø, g for ø and ø, g for ø0 and ø). Order with the following part number when only the grease pack is needed. Grease pack part number: GR-S0 ( g), GR-S-0 ( g) Series C Series C
Series C Dimensions asic: CS(D) Stroke SW KK PL 2 x EE PL ød øe E R ø ød W ø W R E L VD L2 L G W G x RT ZZ + Stroke Cushion valve L + Stroke G V With rod boot l f h h + L + V + Stroke Stroke range ø ød Without rod boot With rod boot d EE PL RT L KK SW G G L VD V W W W ZZ E R Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 2 3 G / G / G / G 3/ G 3/ 3.. M x M x M x. M x. M x.. M x. M x. M x. M x. M x. 3 3. 3... 2 3 3 3 2. 3.. 2 0 Up 00 Up 00 G /2 M x. M x. 3 3 Up 00 Up 00 G /2 M x. 3 M2 x 2 2 0 2 Minimum stroke for trunnion mounting are below. Tube I.D. : 0 mm, Tube I.D. 0: mm, Tube I.D. : mm l h L2 L ød øe f 0 0 0 0 0 0 0 0 0 0 00 0 00 00 0 0 0 0 0 0 00 0 00 00.. 3. 3. 0 0 2 2 0 0 2 2 0 3 3 3 23 2 2 33 0 3 3 3 23 2 2 33 2 2.. 3. 3. 0 0 2 2 0 0 2 2 0 0 2 2 2 0 0 0 2 2 2 0 0 2.. 3. 3. 0 0 2 2 3 2 2 2 2 3 3 0 0 2 2 3 2 2 2 2 3 3 0 0 0 0 0 2 2 2 2 0 0
ISO Standards ir Cylinder: Standard Type Double cting, Single/Double Rod Series C Dimensions asic: CS(D) Stroke ø ød SW KK PL 2 x EE PL W W SW KK ød ø Series C ød øe L VD L2 With rod boot at one end L G RT Cushion valve W G G W + Stroke L + Stroke + Stroke ZY + 2 x Stroke VD L2 L Series CP l h h + L + + 2 x Stroke f With rod boot at both ends ød øe øe ød Series C h l f L + Stroke 2 x h + L + 2 x Stroke f l + Stroke h + Stroke ø ød EE PL RT L KK SW G G L VD W W W ZY d 0 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 Up 00 2 3 G / G / G / G 3/ G 3/ G /2 G /2 3.. M x M x M x. M x. M x. M x. M x.. 3 M x. M x. M x. M x. M x. M x. M2 x 2 3 2 3. 3. 3 0. Minimum stroke for trunnion mounting are below. Tube I.D. : 0 mm, Tube I.D. 0: mm, Tube I.D. : mm 0 Stroke range l h ød øe f 0 0 0 0 0 0 0 0 0 0 00 0 00 00 0 0 0 0 0 0 00 0 00 00.. 3. 3. 0 0 2 2 0 0 2 2 0 3 3 3 23 2 2 33 0 3 3 3 23 2 2 33.. 3. 3. 0 0 2 2 0 0 2 2 0 0 2 2 2 0 0 0 2 2 2 0 2.. 3. 3. 0 0 2 2 3 2 2 2 2 3 3 0 0 2 2 3 2 2 2 2 3 3 0 0 0 0 0 2 2 2 2 0 0. 2 3 3 0 23 2 0 0 3 L2 2 2 L Series C
Series C Dimensions xial foot (L) X + Stroke x ø TR E T O S + Stroke O Center trunnion (T) Z + /2 Stroke XV +/2 Stroke UW øtd Rod flange (F) x F L TL TM TL E2 R TF UF W MF ead flange (G) ZF + Stroke MF CD Single clevis (C) Double clevis (D) E 0 0 Max. 2 XD + Stroke TR O T S X TM TL TD e UW.... 3 0 0 0 2. 2 2 3.. 2 2 0 0 Max. Max. 2 20 0 0 L L MR EW C U E XV Z R TF F E2 UF U C CD W MF ZF EW h L MR XD E 3 2 2 0.. 2.. 2 0 2 2 2 0. 0 0 2 0 0 0. 0.. 0 0 0 0. 0 0 0 3 0 0 0. 2 0 3 2 0 Max. Max. 0 0 0. 0..2 Min. Max. 2 2 Max.
Minimum Stroke for u Switch Mounting u switch model D- D-V D-M D-MW D-MV D-MWV D-M D-MV D-3 D-G3 D-K3 D- D- D- D-W D-F D-J D-FW D-JW D-F D-FF D-FNT D-Z D-Z D-Y D-YP D-YW D-Y D-YPV D-YWV D-Y D-PDW 2 Number of au switches With 2 pcs. (Different surfaces, Same surface) With pc. With n pcs. With 2 pcs. (Different surfaces, Same surface) With pc. With n pcs. With 2 pcs. (Different surfaces, Same surface) With pc. With n pcs. With 2 pcs. (Different surfaces, Same surface) With pc. With n pcs. With 2 pcs. (Different surfaces, Same surface) With pc. With n pcs. With 2 pcs. (Different surfaces, Same surface) With pc. With n pcs. With 2 pcs. (Different surfaces) With 2 pcs. (Same surface) With n pcs. (Different surfaces) With n pcs. (Same surface) With pc. With 2 pcs. (Different surfaces) With 2 pcs. (Same surface) With n pcs. (Different surfaces) With n pcs. (Same surface) With pc. With 2 pcs. (Different surfaces, Same surface) With pc. With n pcs. (Same surface) With 2 pcs. (Different surfaces, Same surface) With n pcs. (Same surface) With pc. With 2 pcs. (Different surfaces, Same surface) With n pcs. (Same surface) With n pcs. With n pcs. With 2 pcs. (Different surfaces, Same surface) With pc. With n pcs. Center trunnion ø ø ø ø ø ø0 ø 0 0 + (n )/2 n =,,, + (n )/2 n =,,, + (n )/2 n =,,, + (n )/2 n =,,, + (n )/2 n =,,, + (n )/2 0 + (n )/2 n =,,, n =,,, Support bracket other than center trunnion ø, ø, ø, ø ø, ø0 ø 0 + (n )/2 n =,,, + (n )/2 n =,,, + (n )/2 + (n )/2 + (n )/2 n =,,, n =,,, n =,,, + (n )/2 n =,,, + (n 2)/2 n =,,, + (n 2)/2 n =,,, + (n )/2 n =,,, + (n 2)/2 n =,,, + (n 2)/2 n =,,, + (n )/2 n =,,, + (n )/2 n =,,, 0 + (n )/2 n =,,, + (n )/2 n =,,, 0 + (n )/2 n =,,, + (n )/2 n =,,, + (n )/2 + (n )/2 n =,,, n =,,, 0 + (n )/2 n =,,, + (n )/2 n =,,, 0 + (n 2)/2 + (n 2)/2 0 + (n 2)/2 + (n 2)/2 n =,,, n =,,, n =,,, n =,,, + (n 2)/2 n =,,, 0 + (n 2)/2 n =,,, + (n 2)/2 n =,,, + (n 2)/2 n =,,, + (n 2)/2 n = 2,,, 0 + (n 2)/2 n = 2,,, 0 + (n )/2 n =,,, + (n )/2 n =,,, 0 + (n )/2 n =,,, + (n )/2 n =,,, + (n )/2 n =,,, + (n )/2 + (n )/2 n =,,, n =,,, + (n )/2 + (n )/2 n =,,, n =,,, + (n )/2 n =,,, + (n )/2 n =,,, + (n 2)/2 n = 2,,, + (n 2)/2 n = 2,,, 0 + (n 2)/2 n = 2,,, 0 0 + (n 2)/2 n = 2,,, 0 + (n 2)/2 n = 2,,, 0 3 0 0 0 + (n 2) n = 2,,, 0 + 0 (n 2) n = 2,,, + (n 2) n = 2,,, + 0 (n 2) n = 2,,, + (n 2) n = 2,,, 0 + 0 (n 2) n = 2,,, + (n 2) n = 2,,, + 0 (n 2) n = 2,,, + (n 2) n = 2,,, 0 + (n 2) n = 2,,, + 0 (n 2) + 0 (n 2) n = 2,,, n = 2,,, + (n 2)/2 n = 2,,, 3 + (n 2) n = 2, 3, 0 + 0 (n 2) n = 2, 3, 0 0 0 3 0 0 0 + (n 2) n = 2,,, 0 + (n 2) n = 2,,, + (n 2)/2 n = 2,,, 0 0 0 + (n )/2 n =,,, + (n 2) n = 2,,, + (n 2) n = 2,,, + (n )/2 n =,,, + (n 2) n = 2,,, + (n 2) n = 2,,, + (n 2) n = 2,,, + (n 2) n = 2,,, 0 + (n 2) n = 2,,, 0 + (n 2) n = 2,,, + (n 2)/2 n = 2,,, 0 + (n )/2 + (n )/2 + (n )/2 + (n )/2 n =,,, n =,,, n =,,, n =,,, + (n 2)/2 n = 2,,, 3 + (n 2) n = 2, 3, + (n 2) n = 2, 3, 0 0 + (n 2)/2 n = 2,,, With pc. 0 With 2 pcs. (Different surfaces, 0 Same surface) With n pcs. 0 + (n )/2 + (n )/2 + (n )/2 + (n )/2 + (n )/2 + (n )/2 + (n 2)/2 + (n 2)/2 + (n 2)/2 (Same surface) n =,,, n =,,, n =,,, n =,,, n =,,, n =,,, n = 2,,, n = 2,,, n = 2,,, With pc. 0 With 2 pcs. (Different surfaces, Same surface) 0 0 With pc. With n pcs. + (n )/2 + (n )/2 0 + (n )/2 + (n )/2 0 + (n )/2 + (n )/2 + (n 2)/2 n =,,, n =,,, n =,,, n =,,, n =,,, n =,,, n = 2,,, With 2 pcs. (Different surfaces, Same surface) With pc. With 2 pcs. (Different surfaces, Same surface) With pc. Series C u Switch Mounting + (n )/2 n =,,, + (n )/2 n =,,, + (n )/2 n =,,, 0 + (n )/2 n =,,, 0 + (n )/2 + (n )/2 n =,,, n =,,, + (n )/2 n =,,, 0 + (n )/2 + (n )/2 + (n )/2 + (n )/2 n =,,, n =,,, n =,,, n =,,, + (n 2)/2 n = 2,,, 0 0 0 + (n )/2 n =,,, + (n )/2 n =,,, + (n )/2 n =,,, + (n )/2 n =,,, + (n 2)/2 n = 2,,, + (n 2)/2 n = 2,,, + (n 2)/2 n = 2,,,
u Switch Mounting Series C u Switch Proper Mounting Position (Detection at stroke end) and Its Mounting eight u switch t s Series C u Switch Proper Mounting Position u switch model 0 D- D-V...... D-M D-MV D-MW D-MWV D-MV...... D- D- 0. 0. Note) djust the au switch after confirming the operating condition in the actual setting. u Switch Mounting eight u switch model 0 D- D-M D-MW D-M s 2. 2. 33. 3... t. 3 3.. D-V s 2. 3... t. 3 3.. 0 0 0 0 2. 2. D-MV D-MWV D-MV s. 3 3. 3 2. t. 3 3.. D-W.. 2 2 2. 2... D- D- D-W s 3 3. 3.. 2. t 2. 2. 3. 3... D-FW D-JW D-F D-J D-F D-FF........ D-F D-J D-FF D-FW D-JW D-F D-FNT s t.. 2. 3 3 2... 0.. D-FNT........ D-3 D-G3 D-K3 s. 3. 2. 3 t 2. 2. D-3 D- D-G3 D-K3 0. 0. 0 0 0 0 2. 2. D- s. 3. 3 3. t 2. 2. D-Z D-Z D-Y D-Y D-YP D-YPV D-YW D-YWV D-Y... 2. 2.... D-Z D-Z D-Y D-YP D-YW D-Y s. 2. 33. 3... t 2 3 3. D-PDW 3. 3..... D-Y D-YPV D-YWV s 2. 3.... t 2 3 3. D-PDW s 3 2.... t 3 33 3.. 2 Series CP Series C Series C 3
Series C u Switch Mounting rackets/part No. u switch model ø ø ø ø ø ø0 ø D-/V D-M/MV D-MW/MWV D-M/MV M-0 M-0-0 -0-0 -0-0 D-3/ D-G3/K3 M2-0 M2-0 M-0 M-0 M-0 M-0 S- D-/ D-W D-F/J D-FW/JW D-FF D-F D-FNT D-PDW T-03 M3T-0 T-03 M3T-0 T-0 M3T-0 T-0 M3T-0 T-0 M3T-0 T-0 M3T-0 T-0 P2T-0 Mounting example for D-(V), M(V), MW(V), M(V) D-Z/Z D-Y/Y D-YP/YPV D-YW D-YWV D-Y M-0 M-0 M-0 M-0-0 -0-0 [Stainless Steel Mounting Screw] The following stainless steel mounting screw kit (including set screws) is available. Use it in accordance with the operating environment. (Since the au switch mounting bracket is not included, order it separately.) : For D-//F/J Note ) For details on, refer page. D-F switch is set on the cylinder with the stainless steel screws above when shipped from facry. When only an au switch is shipped independently, the is attached. Note 2) When using type D-M(V) or Y, please do not use the iron set screws included with the au switch mounting bracket (M-0, -, M-, -) shown above, instead order the set of stainless steel set screws (), and please use the stainless steel set screws (M x L) included in. Operating Range u switch model 0 D-/V..... D-M/MV D-MW/MWV D-M/MV. D-Z/Z D-/ D-W D-3/. 3. 3. 3... 3 D-Y/Y D-YP/YV D-YW/YWV D-Y..... D-F/J D-FW/JW D-F/FNT D-FF 3.... D-G3/K3 D-PDW... Values which include hysteresis are for guideline purposes only, they are not a guarantee (assuming approximately ±% dispersion) and may change substantially depending on the ambient environment.
u Switch Mounting Series C Other than the applicable au switches listed in ow Order, the following au switches are mountable. Refer the est Pneumatics No. 2 for the detailed specifications. Type Sold state Reed Part no. D-MNV, MPV, MV D-Y, Y, YPV D-MNWV, MPWV, MWV D-YNWV, YPWV, YWV D-MNV, MPV, MV D-Y, Y, YP D-F, FP, J D-YNW, YPW, YW D-FW, FPW, JW D-F, Y D-FNT D-PDW D-3V, V D-0V D-, Z D-3,, Z3, Z Electrical entry Grommet (Perpendicular) Grommet (In-line) Grommet (Perpendicular) Grommet (In-line) Normally closed (NC = b contact) solid state au switches (D-FG/F/YG/Y) are also available. For details, refer the est Pneumatics No. 2. With pre-wired connecr is also available for solid state au switches. For details, refer the est Pneumatics No. 2. Features Diagnostic indication (2-color indication) Water resistant (2-color indication) Diagnostic indication (2-color indication) Water resistant (2-color indication) With timer Magnetic field resistant (2-color indication) Without indicar light Series C Series CP Warning. Do not open the cushion valve above the spper. Cushion valves are provided with a crimp (ø) or a retaining ring (ø ø0) as a spping mechanism, and the cushion valve should not be opened above that point. If air is supplied and operation started without confirming the above condition, the cushion valve may be ejected from the cover. 2. e certain activate the air cushion at the stroke end. When it is intended use the cushion valve in the fully opened position, select a style with a damper. If this is not done, the tie-rods or pisn rod assembly will be damaged. Specific Product Precautions djustment 3. When replacing brackets, use the hexagon wrenches shown below.,,, 0 Width across flats Tightening rque (N m)..2. Series C Series C
Series C ow Mount and Move the u Switch Mounting racket ow Mount and Move the u Switch u switch Tie-rod Mounting Type <pplicable u Switch> Solid state switch D-G3, D-K3 Reed switch D-33, D-3, D- D-3, D-G3/K3 type u switch mounting screw M x 0. x L ook <pplicable u Switch> Solid state switch D-MN(V), D-MP(V), D-M(V) D-MNW(V), D-MPW(V), D-MW(V) D-MN(V), D-MP(V), D-M(V) Reed switch D-0(V), 3(V), (V) ow Mount and Move the u Switch u switch mounting screw M2. x 0. x L exagon socket head set screw M r Watchmaker s (precision) screwdriver w e Put the au switch on the surface of the cylinder tube. u switch mounting band u switch q u switch mounting bracket D- type u switch u switch mounting screw M x 0. x L Tie-rod Cylinder tube ook. Loosen the au switch mounting screws at both sides pull down the hook. 2. Put an au switch mounting band on the cylinder tube and set it at the au switch mounting position, and then hook the band. 3. Screw lightly the au switch mounting screw (M x 0. x L).. Set the whole body the detecting position by sliding, tighten the mounting screw (M x 0. x L) secure the au switch. (The tightening rque should be about 2 3 N m.). Modification of the detecting position should be made in the state of 3. u Switch Mounting racket Part No. (and) Cylinder series C M2-0 M2-0 pplicable bore size M -0 M -0 M -0 u switch mounting band 0 M -0 S -. Fix it the detecting position with a set screw by installing an au switch mounting bracket in cylinder tie-rod and letting the botm surface of an au switch mounting bracket contact the cylinder tube firmly. 2. Fix it the detecting position with a set screw (M). (Use a hexagon wrench.) 3. Fit an au switch in the au switch mounting groove set it roughly the mounting position for an au switch.. fter confirming the detecting position, tighten up the mounting screw (M2. x 0. x L) attached an au switch, and secure the au switch.. When changing the detecting position, carry out in the state of 3. Note ) To protect au switches, ensure that main body of an au switch should be embedded in au switch mounting groove with a depth of mm or more. Note 2) Set the tightening rque of a hexagon socket head set screw (M) be.0.2 N m. Note 3) When tightening an au switch mounting screw (M2. x 0. x L), use a watchmaker s screwdriver with a grip diameter of mm. lso, set the tightening rque be 0.0 0. N m. s a guide, turn 0 from the position where it comes feel tight. u Switch Mounting racket Part No. (Including racket, Set Screw) Cylinder series C M -0 M -0 pplicable bore size -0-0 -0 0-0 -0 Note ) When using D-M(V) type, please order stainless steel screw set separately (page ), and use the stainless steel set screws, after selecting set screws of the appropriate length for the cylinder seriesas shown in the table above. Note 2) Color or gloss differences in the metal surfaces have no effect on metal performance. The special properties of the chromate (trivalent) applied the main body of the au switch mounting bracket for - and M- result in differences in coloration depending on the production lot, but these have no adverse impact on corrosion resistance.
Series C ow Mount and Move the u Switch 2 Mounting racket Tie-rod Mounting Type <pplicable u Switch> Solid state switch D-Y, Y, D-YP(V) D-YNW(V), YPW(V), YW(V) D-Y Reed switch D-Z3, Z, Z <pplicable u Switch> Solid state switch D-PDW Series C ow Mount and Move the u Switch Watchmaker s (precision) screwdriver Note 2) exagon socket head set screw M x 0. x L u switch u switch mounting screw u switch mounting bracket ow Mount and Move the u Switch exagon socket head cap screw M x 0. x L Tie-rod u switch mounting bracket u switch Series CP Note ) When tightening an au switch mounting screw, use a watchmaker s screwdriver with a handle diameter of mm. lso, set the tightening rque be 0.0 0. N m. s a guide, turn 0 from the position where it comes feel tight. Set the tightening rque of a hexagon socket head set screw (M x 0. x L) be.0.2 N m.. Fix it the detecting position with a set screw by installing an au switch mounting bracket in cylinder tie-rod and letting the botm surface of an au switch mounting bracket contact the cylinder tube firmly. (Use a hexagon wrench.) 2. Fit an au switch in the au switch mounting groove set it roughly the mounting position for an au switch. 3. fter confirming the detecting position, tighten up the mounting screw attached an au switch, and secure the au switch.. When changing the detecting position, carry out in the state of 2. To protect au switches, ensure that main body of an au switch should be embedded in au switch mounting groove with a depth of mm or more. u Switch Mounting racket Part No. (Including racket, Set Screw) Cylinder series C M -0 M -0 Tie-rod pplicable bore size M -0 M -0-0 0-0 -0 Note 2) When using D-Y type, please order stainless steel screw set separately (page ), and use the stainless steel set screws, after selecting set screws of the appropriate length for the cylinder series as shown in the table above.. Slightly screw the hexagon socket head cap screw (M x 0. x L) in the M tapped portion of au switch mounting bracket. (2 locations) Use caution that the tip of the hexagon socket head cap screw should not stick out the concave portion of au switch mounting bracket. 2. Put a hexagon socket head cap screw (M3 x 0. x L) through the au switch's through-hole (2 locations), and then push it down in the M3 tapped part on the au switch mounting bracket while turning it lightly. 3. Place the concave part of the au switch mounting bracket in the cylinder tie-rod, and slide the au switch mounting bracket in order set roughly the detecting position.. fter reconfirming the detecting position, tighten the M3 mounting screw secure the au switch by making the botm face of au switch attached the cylinder tube. (Tightening rque of M3 screw should be 0. 0. N m.). Tighten up M screw of au switch mounting bracket secure the au switch mounting bracket. (Ensure that tightening rque of M screw should be set.0.2 N m.) u Switch Mounting racket Part No. (Including racket, Screw) Cylinder series C M3T -0 M3T -0 pplicable bore size M3T -0 M3T -0 M3T -0 exagon socket head cap screw M3 x 0. x L 0 M3T -0 P2T -0 Series C Series C
Series C Mounting racket Tie-rod Mounting Type <pplicable u Switch> Solid state switch D-F, D-FP D-J, D-J, D-F D-FW, D-FPW, D-JW D-FF, D-FNT Reed switch D-3, D-, D-, D-, D- D-W. Fix the au switch on the au switch mounting bracket with the au switch mounting screw (M) and install the set screw (M). 2. Fit the au switch mounting bracket in the cylinder tie-rod and then fix the au switch at the detecting position with a set screw (M). (e sure put the au switch on the surface of cylinder tube.) (Use a hexagon wrench.) 3. When changing the detecting position, loosen the set screw move the au switch and then re-fix the au switch on the cylinder tube. (Tightening rque of M screw should be.0.2 N m.) Set screw (M) Tie-rod u switch mounting screw (M) u switch u switch mounting bracket u Switch Mounting racket Part No. (Including racket, Screw, Set Screw) Cylinder series C T-03 T-03 pplicable bore size T-0 T-0 T-0 0 T-0 T-0 The following stainless steel mounting screw kit (including set screws) is available. Use it in accordance with the operating environment. (Since the au switch mounting bracket is not included, order it separately.) : For D-//F/J D-F switch is set on the cylinder with the stainless steel screws above when shipped from facry. When only an au switch is shipped independently, the is attached. Stainless Steel Mounting Screw Set Part no. No. 2 Contents Description u switch mounting screw Set screw Size M x 0. x L M x 0. x L pplicable au switch Q'ty mounting bracket part no. T- T-03, T-0, T-0 T-0, T-0, T- -0, -0, -0 2 M-0, M-0 M-0-0, -0, -0 T-, T-, T- 3 Set screw M x 0. x L 2 S-, S-0 S-, S-0 S-, S-0 S-, S-0 Note) Use the set screw after selecting the appropriate length for the au switch mounting bracket. (Example) When using the -0, select the L type. L type is not required. pplicable au switch D-, D-F, J D-Z, Z D-Y, Y, Y D- D-M D-, D-F, J D-Z, Z D-Y, Y, Y D- D-M
Prior Use u Switch Connection and Example Sink Input Specifications Source Input Specifications 3-wire, NPN u switch rown Input lack lue COM (PLC internal circuit) 3-wire, PNP u switch rown lack lue Input COM (PLC internal circuit) Series C 2-wire rown Input 2-wire rown COM u switch u switch lue lue COM Input (PLC internal circuit) (PLC internal circuit) Connect according the applicable PLC input specifications, as the connection method will vary depending on the PLC input specifications. Example of ND (Series) and OR (Parallel) Connection * When using solid state au switches, ensure the application is set up so the signals for the first ms are invalid. 3-wire ND connection for NPN output 3-wire OR connection for NPN output (Using relays) (Performed with au switches only) rown rown rown Relay Load lack lack Load lack Load u switch u switch u switch lue lue lue Series CP rown lack u switch 2 lue 3-wire ND connection for PNP output (Using relays) rown Relay lack u switch rown lack u switch 2 lue (Performed with au switches only) rown lack u switch rown lack u switch 2 lue 3-wire OR connection for PNP output rown lack u switch Series C lue lue lue rown rown rown u switch 2 u switch u switch 2 lack lue 2-wire ND connection rown lue rown lue Load Load When two au switches are connected in series, a load may malfunction because the load voltage will decline when in the ON state. The indicar lights will light up when both of the au switches are in the ON state. u switches with load voltage less than V cannot be used. Load voltage at ON = Power supply voltage Residual voltage x 2 pcs. = 2 V V x 2 pcs. = V Example: Power supply is 2 VDC Internal voltage drop in au switch is V. u switch 2 u switch u switch 2 lack Load lue 2-wire OR connection rown lue rown lue Load u switch 2 (Solid state) When two au switches are connected in parallel, malfunction may occur because the load voltage will increase when in the OFF state. Load voltage at OFF = Leakage current x 2 pcs. x Load impedance = m x 2 pcs. x 3 kw = V Example: Load impedance is 3 kw. Leakage current from au switch is m. lack lue Load (Reed) ecause there is no current leakage, the load voltage will not increase when turned OFF. owever, depending on the number of au switches in the ON state, the indicar lights may sometimes grow dim or not light up, due the dispersion and reduction of the current flowing the au switches. Series C
Series CP/C ccessories Cylinder Mounting ccessories/part No. Rod/ead flange Double clevis (Corresponds E accessory) F D C Single clevis ore size Supplied with screws. 0 Supplied with screws. F F F F F F0 F Refer page 2 for dimensions. Supplied with screws, clevis pin, and safety device. D D D D D D0 D Refer page for dimensions. Plain With ball joint C CS C CS C CS C C C CS C0 CS0 C CS Refer page for dimensions. Foot Double clevis (for ES accessory) Clevis pivot bracket with ball joint L DS ES E Clevis pivot bracket ore size 0 Supplied with 2 pieces and screws. L L L L L L0 L Refer page 2 for dimensions. DS DS DS DS DS DS0 DS Refer page 2 for dimensions. ES ES ES ES ES ES0 ES Refer page 2 for dimensions. E E E E E E0 E Refer page for dimensions. Pisn Rod Mounting ccessories/part No. Rod clevis (ISO ) Pisn rod ball joint (ISO 3) GKM KJ J Floating joint ore size 0 Supplied with clevis pin and safety device. GKM- GKM-2 GKM- GKM- GKM- GKM- GKM- Refer page 3 for dimensions. KJD KJD KJD KJD KJD KJD KJ2D Refer page 3 for dimensions. J-- J-- J-- J-- J-- J-- J-2-0 Refer page 3 for dimensions.
øcd l2 l ø l3 l l2 l Dimensions: Cylinder Mounting ccessories Single clevis (C) Clevis pivot bracket (E) Single clevis with ball joint (CS) Double clevis (D) 0 C 2 2 0 øcd ød 3 ød2.. 3. E 3 Max. FL 2 l2.... L l MR. 2 R.... TG. 3.. 2 U 2 0 0 E2 Max. EW 0. 0. 0. 0. 0. 0. 0..2 2 2 0 0 øck C 0 ød2 G 2 2 33 3 0 G2 3 l. 3. R. øs.. EM 0. 0. 0. 0. 0. 0. 0.. 2 2 0 K 3 2 3 3 0 0 lack color 0. 3.. 2. C 2 ød 2 2 3 2 øf 3 L øm. N.... P EN øe.. 3. 0 0 ±0. 0 0. K2 (Max.) l3 (Max.) G3 (Max.) (Max.) ER (Max.) ccessories Series CP/C Series C Series CP Series C Series C
l l2 L +0.3 0 Dimensions: Cylinder Mounting ccessories Double clevis (DS) Clevis pivot bracket with ball joint (ES) 0 lack color C 0 øcn ød3 EN 2 2 3 2 EU. G 2 2 33 3 0 G2 3 3 3 0 0 l2...... K 3 2 øs.. 3. 0 2 2 3 2 3 3 3.3.3.3.3.3.3.3 øcn ød 3 ød2. ød3.. 3. E 2 FL l2.... L. 2 R 2 3 T 3 TG. 3.. 2 lack color l (Min.) (Max.) ER (Max.) SR (Max.) K2 (Max.) G3 (Max.) 2 Series CP/C
ccessories Series CP/C Dimensions: Pisn Rod Mounting ccessories Floating Joint J,, 0 lack color M Part no. C ød E F G P U M x. J--.. 2 0. M x. J-- 3 3 0. M x. J--.. 3. 2 M x. J-- 2 3.. 2 2 M2 x 2 J-2-0 3 3 3 3 2 2 2 Rod Clevis GKM (ISO ), Supplied with clevis pin and Safety Device Load (kn) Weight (g) 2. 0. 0 0 2 ngle ±0. Series CP l Series C Series C,, 0 e Part no. b d (Shaft) (ole) l M x. GKM- 2 M x. GKM-2 2 M x. GKM- 3 M x. GKM- M2 x 2 GKM- Pisn Rod all Joint KJ (ISO 3) l +0. +0. +0. +0. +0. +0. +0. +0. +0. +0. øf h øf c (Min.) 2 a (Max.) 2 Series C l3,, 0 d3 d Part no. ød h b h (Max.) (Min.) α M x. 3 2 M x. M x. 2 2 2 M x. 33 M2 x 2 0 3 KJD KJD KJD KJD KJ2D l l3 2 3
Series CP/C Simple Specials These changes are dealt with Simple Specials System. Change of Rod End Shape Symbol -X0 -X pplicable Series Series C CP Description Standard type Smooth type Standard type Model CS CSW CY CPS CPSW ction Double acting, Single rod Double acting, Double rod Double acting, Single rod Double acting, Single rod Double acting, Double rod Symbol for change of rod end shape X0 X0 X0 X0 X0 Precautions. SMC will make appropriate arrangements if no dimension, lerance, or finish instructions are given in the diagram. 2. Standard dimensions marked with will be as follows the rod diameter (D). Enter any special dimension you desire. D D- mm < D D-2 mm D > D- mm 3. In the case of double rod type and single acting retraction type, enter the dimensions when the rod is retracted.. Only the single side of a double rod is able manufacture. Symbol: 0 Symbol: Symbol: 2 Symbol: 3 Symbol: C C0. ød ørd T W L Symbol: Symbol: Symbol: Symbol: Symbol: ørd MM L MM L MM L C0. file chamfer C W W L Symbol: R sphere TP Symbol: R sphere ødc Symbol: Symbol: 3 Symbol: C0. R sphere ød C ød T W L ød MM Symbol: Symbol: Symbol: Symbol: Symbol: C ød L ød MM T W MM MM C MM C Symbol: Symbol: 2 Symbol: Symbol: MM MM ød MM ød ørd L Symbol: 2 MM L K ød Symbol: Symbol: 2 Symbol: 2 MM MM T ød ød MM MM ød T C W Symbol: 2 ød L Symbol: 2 W L L L K Symbol: L L K L L MM T L MM W T
Simple Specials Series CP/C 2 Change of Trunnion racket Mounting Position The position for mounting the trunnion pivot bracket on the cylinder can be moved from the standard mounting position any desired position. pplicable Series Series C Description Standard type Model C CW ction Double acting, Single rod Double acting, Double rod Note Symbol -XC Series C (Z + /2 stroke) = Precautions Trunnion position for -XC Trunnion position for -XC. Specify Z + /2 stroke in the case the trunnion bracket position is not -XC, or trunnion is not a center trunnion. 2. SMC will make appropriate arrangements if no dimension, lerance, or finish instructions are given in the diagram. 3. The possible range of trunnion bracket mounting position is indicated in the table below.. Some trunnion mounting positions do not allow au switch mounting. Please consult with SMC for more information. Series CP Series C Symbol Trunnion bracket position 0 Minimum 3... 2. For -XC Maximum + Stroke + Stroke + Stroke. + Stroke. + Stroke. + Stroke. + Stroke Reference: Standard (Center trunnion) + 0. stroke. + 0. stroke 2 + 0. stroke. + 0. stroke + 0. stroke 0 + 0. stroke + 0. stroke Minimum stroke 0 Series C Series C
Series CP/C Made Order Please contact SMC for detailed dimensions, specifications and lead times. 3 eat Resistant Cylinder ( C) Symbol -X ir cylinder which changed the seal material and grease, so that it could be used even at higher temperature up from C. pplicable Series Series CP C Description ir cylinder ir cylinder Model CPS CPSW CS CSW ction Double acting, Single rod Double acting, Double rod Double acting, Single rod Double acting, Double rod Note Page for the standard type Page 3 Page ow Order Standard model no. X Specifications eat resistant cylinder mbient temperature range C Seal material Fluororubber Grease eat resistant grease Note ) Operate without lubrication from a pneumatic system lubricar. Note 2) Please contact SMC for details on the maintenance intervals for this cylinder, which differ from those of the standard cylinder. Note 3) In principle, it is impossible make built-in magnet type and the one with au switch. ut, as for the one with au switch, and the heat resistant cylinder with heat resistant au switch, since it will be differed depending on the series, please contact SMC. Note ) Pisn speed is ranged from 0 mm/s. Specifications other than above and external dimensions Same as standard type Warning Precautions e aware that smoking cigarettes etc. after your hands have come in contact with the grease used in this cylinder can create a gas that is hazardous humans. Cold Resistant Cylinder ( 0 C) Symbol -X ir cylinder which changed the seal material and grease, so that it could be used even at lower temperature down C. pplicable Series Series C Description ir cylinder Model CS ction Double acting, Single rod Note Except with au switch. Mounting bracket: asic type only. Minimum operating pressure 0.2 MPa Page for the standard type Page ow Order Standard model no. X Specifications Cold resistant cylinder mbient temperature range 0 C Seal material Low nitrile rubber Grease Cold resistant grease u switch Not mountable Dimensions Same as standard type Note ) Operate without lubrication from a pneumatic system lubricar. Note 2) Use dry air which is suitable for heatless air dryer etc. not cause the moisture be frozen. Note 3) Please contact SMC for details on the maintenance intervals for this cylinder, which differ from those of the standard cylinder. Note ) Mounting au switch is impossible. Specifications other than above Same as standard type Warning Precautions e aware that smoking cigarettes etc. after your hands have come in contact with the grease used in this cylinder can create a gas that is hazardous humans.
Made Order Series CP/C With eavy Duty Scraper Symbol -XC It is suitable for using cylinders under the environment, where there are much dusts in a surrounding area by using a heavy duty scraper on the wiper ring, or using cylinders under earth and sand exposed the die-casted equipment, construction machinery, or industrial vehicles. pplicable Series Series CP C Description ir cylinder ir cylinder ow Order Standard model no. Model CPS CPSW CS CSW With heavy duty scraper (SC scraper) XC Specifications: Same as standard type Dimensions: Same as standard type ction Double acting, Single rod Double acting, Double rod Double acting, Single rod Double acting, Double rod Note ø ø0 ø ø0 ø ø0 ø ø0 Page for the standard type Page 3 Page Series C Series CP Caution Do not replace heavy duty scrapers. Since heavy duty scrapers are press-fit, do not replace the cover only, but rather the entire rod cover assembly. pplicable Series Series CP C Tie-rod, Cushion Valve, Tie-rod Nut, etc. Made of Stainless Steel Description ir cylinder ir cylinder ow Order Standard model no. Tie-rod, cushion valve, tie-rod nut, etc. made of stainless steel Model ction Page for the standard type CPS CS Double acting, Single rod Double acting, Single rod CPSW CSW Double acting, Double rod Double acting, Double rod Page 3 Page XC Symbol -XC When using in locations where the rust generation or corrosion likelihood exists, the standard parts material have been partly changed the stainless steel. Series C Series C Specifications Parts changed stainless steel Specifications other than above Dimensions Tie-rod, Tie-rod nut, Mounting bracket nut, Spring washer, Cushion valve, Lock nut Same as standard type Same as standard type
Series CP/C Dual Stroke Cylinder/Double Rod Type Symbol -XC Two cylinders are constructed as one cylinder in a back--back configuration allowing the cylinder stroke be controlled in three steps. pplicable Series Series CP C Description ir cylinder ir cylinder Model ction Note Page for the standard type CPS Double acting, Single rod Except clevis and trunnion types Page 3 CS Double acting, Single rod Except clevis and trunnion types Page ow Order CPS Mounting style Stroke + Stroke XC CS Specifications Series CP C Dual stroke cylinder Maximum manufacturable stroke 00 Function DC When air pressure is supplied ports stroke D C and, both and strokes retract. When air pressure is supplied ports and D, out strokes. D C stroke When air pressure is supplied ports and C, out strokes. stroke D C stroke When air pressure is supplied ports C and D, both strokes and out strokes. Dimensions (Dimensions other than below are the same as standard type.) Stroke Stroke N GC N L + Stroke ( + ) ZZ + Stroke ( + ) Stroke Stroke N GC N L + Stroke ( + ) ZZ + Stroke ( + ) ø ø ø ø ø ø0 ø L 2 2 2 20 20 33 ZZ 2 0 30 2 2 2 N 0 N GC 3 3 2 2 2
Made Order Series CP/C pplicable Series Series CP C Dual Stroke Cylinder/Single Rod Type Two cylinders can be integrated by connecting them in line, and the cylinder stroke can be controlled in two stages in both directions. Description ir cylinder ir cylinder Model ction Note Page for the standard type CPS Double acting, Single rod Except trunnion type Page 3 CS Double acting, Single rod Except trunnion type Page ow Order CPS Mounting style Stroke + Stroke - XC CS Specifications: Same as standard type Function Functional description of dual stroke cylinder C ) Initial state (0 stroke position) Dual stroke cylinder/single rod type Symbol -XC Series C Series CP stroke stroke - stroke stroke stroke C C C stroke 2) st stage: stroke operation When the air pressure is supplied from the port, the rod operates the stroke. 3) 2nd stage: - stroke operation Following the st stage, when the air pressure is supplied from the C port, the rod operates the - stroke. ) Cylinder retraction When the air pressure is supplied from the port, the rod retracts completely. Series C stroke or stroke operation can be made individually. C stroke operation stroke stroke stroke stroke C C C stroke stroke ) Initial state (0 stroke position) 2) Operation When the air pressure is supplied from the port, the rod operates the stroke. stroke operation ) Initial state (0 stroke position) 2) Operation When the air pressure is supplied from the C port, the rod operates the stroke. Series C Double output is possible. stroke W W stroke C stroke C ) Initial state (0 stroke position) 2) Double output When the air pressure is supplied the and C ports at the same time, the double output can be obtained in the stroke range. Precautions Caution. Do not supply air until the cylinder is fixed with the attached bolt. 2. If air is supplied without securing the cylinder, the cylinder could lurch, posing the risk of bodily injury or damage the peripheral equipment.