ARXPS analysis of a GaAs/GalnP heterointerface with application in III-V multijunction solar cells

Similar documents
PHI 5000 Versaprobe-II Focus X-ray Photo-electron Spectroscopy

Temperature Dependent Current-voltage Characteristics of P- type Crystalline Silicon Solar Cells Fabricated Using Screenprinting

Auger Electron Spectroscopy

Optical Investigation of the Localization Effect in the Quantum Well Structures

Auger Electron Spectroscopy (AES)

The Benefit of Wide Energy Range Spectrum Acquisition During Sputter Depth Profile Measurements

Methods of surface analysis

QUESTIONS AND ANSWERS

X-Ray Photoelectron Spectroscopy (XPS) Prof. Paul K. Chu

Birck Nanotechnology Center XPS: X-ray Photoelectron Spectroscopy ESCA: Electron Spectrometer for Chemical Analysis

X-Ray Photoelectron Spectroscopy (XPS)-2

Advanced Lab Course. X-Ray Photoelectron Spectroscopy 1 INTRODUCTION 1 2 BASICS 1 3 EXPERIMENT Qualitative analysis Chemical Shifts 7

IV. Surface analysis for chemical state, chemical composition

Dopant and Self-Diffusion in Semiconductors: A Tutorial

The Inclusion of Impurities in Graphene Grown on Silicon Carbide

MS482 Materials Characterization ( 재료분석 ) Lecture Note 2: UPS

Photoelectron Spectroscopy. Xiaozhe Zhang 10/03/2014

ELECTRONIC STRUCTURE OF InAs/GaAs/GaAsSb QUANTUM DOTS

Surface analysis techniques

Local Anodic Oxidation of GaAs: A Nanometer-Scale Spectroscopic Study with PEEM

Lecture 5. X-ray Photoemission Spectroscopy (XPS)

Xing Sheng, 微纳光电子材料与器件工艺原理. Doping 掺杂. Xing Sheng 盛兴. Department of Electronic Engineering Tsinghua University

Fig 1: Auger Electron Generation (a) Step 1 and (b) Step 2

Temperature Dependent Optical Band Gap Measurements of III-V films by Low Temperature Photoluminescence Spectroscopy

Chemical Analysis in TEM: XEDS, EELS and EFTEM. HRTEM PhD course Lecture 5

Energy Spectroscopy. Ex.: Fe/MgO

Atomic Level Analysis of SiC Devices Using Numerical Simulation

3.1 Introduction to Semiconductors. Y. Baghzouz ECE Department UNLV

X-ray photoelectron spectroscopic characterization of molybdenum nitride thin films

Inelastic soft x-ray scattering, fluorescence and elastic radiation

Local Anodic Oxidation with AFM: A Nanometer-Scale Spectroscopic Study with Photoemission Microscopy

Ion sputtering yield coefficients from In thin films bombarded by different energy Ar + ions

X-Ray Photoelectron Spectroscopy (XPS)-2

Electron Spectroscopy

LOW-TEMPERATURE Si (111) HOMOEPITAXY AND DOPING MEDIATED BY A MONOLAYER OF Pb

Introduction to X-ray Photoelectron Spectroscopy (XPS) XPS which makes use of the photoelectric effect, was developed in the mid-1960

Auger Electron Spectroscopy (AES) Prof. Paul K. Chu

X-ray photoelectron spectroscopy investigation of the mixed anion GaSb/lnAs heterointerface

A semiconductor is an almost insulating material, in which by contamination (doping) positive or negative charge carriers can be introduced.

Surface compositional gradients of InAs/GaAs quantum dots

A DIVISION OF ULVAC-PHI

X-ray photoelectron spectroscopy - An introduction

Transient lattice dynamics in fs-laser-excited semiconductors probed by ultrafast x-ray diffraction

Secondary ion mass spectrometry (SIMS)

A COMPARATIVE CHEMICAL STUDY OF THE TOP LAYERS OF TWO DIFFERENT QUALITY SILICON SOLAR CELLS

High Resolution Photoemission Study of the Spin-Dependent Band Structure of Permalloy and Ni

3.155J/6.152J Microelectronic Processing Technology Fall Term, 2004

Reduced preferential sputtering of TiO 2 (and Ta 2 O 5 ) thin films through argon cluster ion bombardment.

Name: (a) What core levels are responsible for the three photoelectron peaks in Fig. 1?

Photoelectron Interference Pattern (PEIP): A Two-particle Bragg-reflection Demonstration

raw materials C V Mn Mg S Al Ca Ti Cr Si G H Nb Na Zn Ni K Co A B C D E F

Studying Metal to Insulator Transitions in Solids using Synchrotron Radiation-based Spectroscopies.

1 Introduction COPYRIGHTED MATERIAL. 1.1 HowdoweDefinetheSurface?

Reflection high energy electron diffraction and scanning tunneling microscopy study of InP(001) surface reconstructions

Photoelectron spectroscopy Instrumentation. Nanomaterials characterization 2

Transparent Electrode Applications

High-Precision Evaluation of Ultra-Shallow Impurity Profiles by Secondary Ion Mass Spectrometry

Spectromicroscopic investigations of semiconductor quantum dots. Stefan Heun, Laboratorio TASC INFM-CNR, Trieste, Italy.

Core Level Spectroscopies

XPS/UPS and EFM. Brent Gila. XPS/UPS Ryan Davies EFM Andy Gerger

SHG Spectroscopy. Clean surfaces Oxidation SOI wafer

MSE 321 Structural Characterization

Electrons are shared in covalent bonds between atoms of Si. A bound electron has the lowest energy state.

5) Surface photoelectron spectroscopy. For MChem, Spring, Dr. Qiao Chen (room 3R506) University of Sussex.

Chapter 7. Solar Cell

Fundamentals of Nanoscale Film Analysis

Characterization of Secondary Emission Materials for Micro-Channel Plates. S. Jokela, I. Veryovkin, A. Zinovev

ToF-SIMS or XPS? Xinqi Chen Keck-II

Auger Electron Spectroscopy Overview

EE 527 MICROFABRICATION. Lecture 5 Tai-Chang Chen University of Washington

Wide-gap Semiconducting Graphene from Nitrogen-seeded SiC

Xps Study of the Oxidation State of Uranium Dioxide

Nanotechnology and Solar Energy. Solar Electricity Photovoltaics. Fuel from the Sun Photosynthesis Biofuels Split Water Fuel Cells

Quantum Condensed Matter Physics Lecture 12

Effects of plasma treatment on the precipitation of fluorine-doped silicon oxide

Gaetano L Episcopo. Scanning Electron Microscopy Focus Ion Beam and. Pulsed Plasma Deposition

PHOTOLUMINESCENCE STUDY OF INGAAS/GAAS QUANTUM DOTS

Determining Chemical Composition. Of Sputtered Uranium Oxide Thin Films. through X-Ray Photoelectron Spectroscopy

Paper presentation. M S Bootha Raju Date: 28/11/09

Two-dimensional lattice

X-ray Photoelectron Spectroscopy (XPS)

Practical Surface Analysis

Mesoporous titanium dioxide electrolyte bulk heterojunction

Secondary Ion Mass Spectrometry (SIMS) Thomas Sky

X-ray Photoemission Spectroscopy (XPS - Ma4)

Photon Interaction. Spectroscopy

A new approach to AFM investigation of buried Al/In x Ga 1-x As/GaAs interfaces and quantum dots

Spectro-microscopic photoemission evidence of surface dissociation and charge uncompensated areas in Pb(Zr,Ti)O 3 (001) layers

Characterization of Ultra-Shallow Implants Using Low-Energy Secondary Ion Mass Spectrometry: Surface Roughening under Cesium Bombardment

Lecture 23 X-Ray & UV Techniques

Nanocrystalline Si formation inside SiN x nanostructures usingionized N 2 gas bombardment

Chapter 4 Scintillation Detectors

X- ray Photoelectron Spectroscopy and its application in phase- switching device study

EE495/695 Introduction to Semiconductors I. Y. Baghzouz ECE Department UNLV

Study of interface asymmetry in InAs GaSb heterojunctions

Physics of Semiconductors

IEEE JOURNAL OF PHOTOVOLTAICS 1. Vidya Ganapati, Chi-Sing Ho, and Eli Yablonovitch

Opportunities for Advanced Plasma and Materials Research in National Security

Practice question related to The wave nature of electrons Energy level diagrams for atoms, molecules and solids

Raman spectroscopy of self-assembled InAs quantum dots in wide-bandgap matrices of AlAs and aluminium oxide

Transcription:

ARPS analysis of a GaAs/GalnP heterointerface with application in III-V multijunction solar cells M. Gabás, M.C. López-Escalante, C. Algora, I. Rey-Stolle, B. Galiana, S. Palanco, J.R. Ramos- Barrado Abstract In this contribution, angle-resolved -ray photoelectron spectroscopy is used to explore the extension and nature of a GaAs/GalnP heterointerface. This bilayer structure constitutes a very common interface in a multilayered III-V solar cell. Our results show a wide indium penetration into the GaAs layer, while phosphorous diffusion is much less important. The physico-chemical nature of such interface and its depth could deleteriously impact the solar cell performance. Our results probe the formation of spurious phases which may profoundly affect the interface behavior. Index terms gallium arsenide, heterojunctions, III-V semiconductor materials, -ray photoelectron spectroscopy, interface analysis. I. INTRODUCTION Photoelectron spectroscopies (PES) are widely used in the surface and interface analysis. Usually, when incident photons are provided by -ray sources they yield information on the first few nanometers of the layer. However the information depth can be easily modulated by varying the take-off angle of the emitted photoelectrons. Angle-resolved -ray photoelectron spectroscopy (ARPS) is thus a non-destructive analysis technique and moreover, the provided information is not affected by sample experimental damage, as it could happen when Ar + sputtering is used in combination with PES, in order to study a buried surface or interface. An estimate of the sampling depth can be obtained taking into account that the photoelectrons mean free path is only dependent on both matrix effects and photoelectron kinetic energy. Thus, every core level will provide information up to a certain depth in the sample. ARPS allows the selection of the mean information depth since data taken at small take-off angles supply information of the more superficial layers, while photoelectrons coming out at take-off angles close or equal to 90 provide information from a deeper level in the sample. The interfaces between two layers of a III-V multijunction solar cell used in concentrator systems is a device critical part, since existing defects and impurities diffusion can profoundly affect the final device performance. III-V multijunction solar cells are made up of more than 20 different layers, with more than 6 different semiconductor elements, thicknesses varying from nanometer scale to 2 microns and with doping levels going from 10 17 to 10 20 cm" [1]. Multijunction solar cells based on such complex structures have been able to achieve efficiencies well over 40% [2]. Every surface and interface in this layered structure is a potential object of analysis using PES techniques. One of the key tasks in these cells is the optimization of the heteroepitaxial growth of III-V layers onto the former one. A fundamental problem in III-V solar cells is the crossdiffusion during the epitaxial growth of different atoms at the various interfaces in the structure. The interfaces between two III-V semiconductors have received much attention because of their fundamental role on the performance of the solar cell device. In that way, the indepth resolution that PS can supply is of great relevance in order to determine the abruptness of a heterojunction. Their advantages as non-destructive and with a subnanometer in-depth resolution make ARPS very competitive against secondary ion/neutral mass spectrometries (SIMS/SNMS) and the easy-handle sample management makes it more convenient than high resolution transmission electron microscopy (HRTEM). A first approach to the GaAs/GalnP interface was done using -ray photoelectron spectroscopy (PS) in combination with Ar + sputtering [3]. However, some of the effects on the sample surface due to the Ar + sputtering process (preferred sputtering, metal reduction and Ar implantation) were detected in our study. In order to avoid such undesirable effects, an ARPS analysis has been conducted and it is presented in this contribution.

II. EPERIMENTAL A multilayer III-V semiconductor structure was grown by MOVPE (Metal Organic Vapour Phase Epitaxy). It is made up of an undoped GaAs cap layer, a tellurium doped GalnP and a final undoped GaAs layer on a SI-GaAs substrate. The nominal layer thicknesses were 5, 338 and 407 nanometers, respectively. This structure contains a GaAs/GalnP heterointerface which is common in III-V multijunction solar cells. ARPS spectra were recorded on a Physical Electronics PHI 5700 spectrometer using non-monochromated Mg Ka and Al Ka radiation (hv = 1253.6 and 1486.6 ev, respectively). The acceptance angle of the analyzer has been set to 14 and the angle between the incident -rays and the analyzer is 54. The direction of the outcoming photoelectrons is given by the polar angle 0, referred to the sample surface and the azimuth. In order to obtain angle dependent PS results, the polar angle is varied from 30 to 90. The different take-off angles were used to vary the photoelectron path in the solid and hence the sampling depth, with the smaller take-off angle being more surface sensitive. The core level spectra were fitted using the PSPeak software package [4]. signal are in good agreement with those presented in previous literature [6]. 1 «i i ' i ' i i i «i > i i I 1130 1125 1120 1115 1110 BE(eV) III. RESULTS Photoelectrons leaving the sample surface have a different escape length depending on their kinetic energy. The corresponding inelastic mean free path (IMFP) multiplied by sino allows to estimate this escape length. Every core level is thus a probe from a different depth under the sample surface. Core levels 2p 3/2 from both, Ga and As elements have the smaller escape depth since the photoelectron kinetic energies coming out the surface layer are very low. In figure 1, the obtained PS signal from Ga 2p 3/2 (top) and As 2p 3/2 (bottom) at various take-off angles are depicted. For these two core levels the escape depths run from -0.65 to -1.35 nm, corresponding to polar angles 30 and 90, respectively. As it is shown in figure 1, As 2p 3/2 shape evolves as the escape depth does, while Ga 2p 3/2 maintains a very similar profile. A detailed analysis of these signals indicates that Ga is more oxidized than As at the surface layer which is in accordance with some other previous reports [5]. The deconvolution of Ga 2p 3/2 and As 2p 3/2 core level signals measured with a take-off angle of 30 are depicted in Figure 2 with their corresponding fits. The mean escape depth corresponding to these analyses is 0.65 nm. Oxidized Ga is in the form Ga 2 0 3 while As presents two oxidation states, As 2 0 3 and As 2 0 5. The binding energy shifts among the various constituents in the As 2p 3/2 Fig. 1: Ga 2p 3/2 (top) and As 2p 3/2 (bottom) core levels PS signal at various take-off angles. To investigate the diffusion of elements from the buried GalnP layer into the GaAs cap layer, the P 2p and the In 3d core levels have monitored at the different take-off angles. P 2p core level is not detectable up to 3.5 nm deep in the GaAs layer. Assuming the nominal thickness of 5 nm for the GaAs cap layer, phosphorus diffusion is limited to a small length across the interface.

contribution is probably due to the formation of an InAs phase or an InGaAs phase. They would be undistinguishable since the In3d core level binding energy should be very similar given that they both have the same crystallographic structure. The presence of the ternary phase GalnP should be discarded at this point, since the P 2p signal is negligible up to 3.5 nm deep in the layer. The signal-to-background ratio increases as the escape depth do, suggesting thus an enrichment of the In content in the layer when approaching the GaAs/GalnP interface. Fig. 2: deconvolution of Ga 2p 3/2 (top) and As 2p 3/2 (bottom) core levels PS signals. The different constituents are labeled in the figures. On the contrary, In 3d core level is measurable at the surface of the GaAs layer. The penetration of this element reaches the whole thickness of the GaAs cap layer. The analysis of the In 3d core level at 30 and 90 take-off angles shows that this element is partially oxidized, although the ln 2 0 3 quantity decreases quickly as the sampling depth does, which implies a thin In oxide layer at the film surface. In figure 3, the deconvolution of the In3d core level signal at two different take-off angles, 30 (top) and 90 (bottom), is presented. The spin orbit splitting (SOS) factor is 7.54 ev. For the two escape lengths -1.5 nm (30 ) and 3.1 nm (90 )- there are two contributions in the PE spectra. The one at higher binding energies represents the 30% of the global intensity for the data taken at 30, while it diminishes to 15% when data are collected at 90. That points to the presence of ln 2 0 3 as a thin layer at the topmost layer surface. The main Fig. 3: deconvolution of the In 3d core level signal, data taken at take-off angles 30 (top) and 90 (bottom) which correspond to escape depths of 1.5 and 3.1 nm, respectively. On the other hand, 3d core levels from Ga and As give information up to 1.9 nm (30 ) or 3.8 nm (90 ) deep under the film surface. Figure 4 shows the deconvolution of the 3d core level signal taken at 30, for both, As (top) and Ga (bottom). The different constituents are doublets with SOS values of 0.69 ev (As 3d) and 0.44 ev (Ga 3d). The As 3d signal has two contributions, which can be ascribed to As 2 0 3 (BE = 44.4 ev) and a mixture of both arsenides

GaAs and InAs or a InGaAs phase with an In content increasing with depth, according to what has been found in the analysis of In3d core level. The estimated escape depth at 30 for photoelectrons coming from these core levels are 1.5 nm and 1.9 nm, for In3d and As3d respectively. According to that, the information from these core levels is complementary. Ga 3d core level has a rather complicated spectrum since the In 4d core level (SOS = 0.86 ev) is in the same energy region (~17eV). Thus, it should be included in the signal deconvolution (see figure 4 bottom). In that way, Ga3d core level has 4 contributions, the one at bigger binding energies corresponds to the oxide Ga 2 0 3, the main one being the GaAs. The ones at lower binding energies correspond to the In4d core level from the InAs or InGaAs phase and the ln 2 0 3. similar to those taken at 30, and the deconvolution analysis (not shown here) varied only in the diminishing quantity of oxides contribution intensities. However, the data measured at 90 (mean escape depth -3.8 nm) show an important difference compared to the former ones. The main signal component diminishes its full width at half maximum: from 1.35 to 1.1 ev for the As 3d core level and from 1.4 to 1.1 ev for the Ga 3d core level (see figure 5). The intensity of the contribution from oxides in both core levels has diminished, being negligible for the ln 2 0 3. 3 3 CO - Q- GaAs / l + J InAs/lnGaAsfv 1 A *A BE {ev) - ' 1 r~ i i i i i i i i i 50 48 46 44 42 40 38 36 *->. co - a. GaAs / / \\ + --»x/ \\ InAs/lnGaAs/ jf 11 GaO I/ l\ \ \ JL InAs/lnGaAs D CO. Q_ I? I\ Ga 2 0 3 J\ V *v InAs/lnGaAs ' ' 1 1 < 1 1 1 ' 1 " " " " " " " " - - - - > 28 26 24 22 20 18 16 Fig. 5: deconvolution of 3d core level signals taken at 90 : As (top) and Ga (bottom). i 1 1 1 1 1 1 1 28 26 24 22 20 18 16 Fig. 4: deconvolution of 3d core level signals taken at 30 : As (top) and Ga (bottom). The data obtained from these core levels measured at 60 polar angle (mean escape depth -3.3 nm) looked very This fact is maybe related with the above mentioned In enrichment when approaching the interface and/or with the formation of new phases due to the presence of P at depths bigger than 3.5 nm. The composition of these phases would be uncertain. In that way, the quantity of pure GaAs phase would have diminished significantly close to the interface or it would be distorted.

IV. SUMMARY AND CONCLUSIONS [6] C.C. Surdu-Bob, S.O. Saied, J.L. Sullivan, "An -ray photoelectron spectroscopy study of the oxide of GaAs", ARPS has been used in the study of a GaAs/GalnP Appl. Surf. Sci. vol. 83, pp. 126-136,2001. heteroface which is very common in III-V multijunction solar cells. In spite of such interface was grown by MOVPE and was intended to be abrupt, the ARPS measurements show an In penetration into the cap GaAs layer. The formation of spurious phase like InAs or more probably an InGaAs intermediate compound is strongly suggested. Our experimental data evidences an In enrichment close to the "nominal" GaAs/GalnP interface, which would support the formation of the InGaAs phase. The formation of new spurious phases with unknown composition and/or the GaAs phase distortion cannot be discarded. Therefore, ARPS seems to be of great help in the study and experimental optimization of heterofaces of III-V multijunction solar cells. ACKNOWLEGMENTS This work has been supported by the Spanish Ministerio de Economía y Competitividad with the projects TEC2011-28639-C02-01 and -02 and with the INNPACTO program by means of the IPT-2011-1441- 920000 and IPT-2011-1408-420000 projects. This project has been also supported by the Comunidad de Madrid under the NUMANCIA II program (S2009/ENE1477). REFERENCES [1] I. Rey-Stolle, C. Algora, E. Barrigón, E. García-Tabarés, I. Garcia, P. Espinet, "Status of Ultra-High Concentrator Multijunction Solar Cell Development at IES-UPM", 5th World Conference on Photovoltaic Energy Conversion (Valencia, España), 2010. [2] M. A. Green, K. Emery, Y. Hishikawa, W. Warta, E. D. Dunlop, Solar cell efficiency tables (version 39), Progress in Photovoltaics: Research and Applications vol. 20, pp. 12-20, 2012. [3] M.C. López, B. Galiana, C. Algora, I. Rey-Stolle, M. Gabás, F. Martín, J.R. Ramos-Barrado "Chemical characterization of GaAs/InGaP heterointerfaces grown by metal organic vapor phase epitaxy (MOVPE) by PS and ARPS", 22nd Eur. Photovolt. Solar Energy Conf, 2007, pp. 253-255. [4] http://public.wsu.edu/~scudiero/index.html last access date 10/05/2012. [5] M. Lazzarino, M. Padovani, G. Mori, L. Sorba, M. Fanetti, M. Sancrotti "Chemical composition of GaAs oxides grown by local anodic oxidation: a spatially resolved Auger study", Chem. Phys. Lett. vol. 40, pp. 155-159, 2005.