, A, B, C Designed for Complementary Use with the BD26 Series W at 25 C Case Temperature 0 A Continuous Collector Current 5 A Peak Collector Current Customer-Specified Selections Available B C E SOT-9 PACKAGE (TOP IEW) 2 Pin 2 is in electrical contact with the mounting base. MDTRAAA absolute maximum ratings at 25 C case temperature (unless otherwise noted) voltage (R BE = Ω) voltage ( = 0 ma) RATING SYMBOL ALUE UNIT A B C A B C Emitter-base voltage EBO 5 Continuous collector current 0 A Peak collector current (see Note ) M 5 A Continuous base current I B A Continuous device dissipation at (or below) 25 C case temperature (see Note 2) P tot W Continuous device dissipation at (or below) 25 C free air temperature (see Note ) P tot W Unclamped inductive load energy (see Note ) ½LI 2 C 62.5 mj Operating junction temperature range T j -65 to +50 C Storage temperature range T stg -65 to +50 C Lead temperature.2 mm from case for 0 seconds T L 250 C NOTES:. This value applies for 0. ms, duty cycle 0%. 2. Derate linearly to 50 C case temperature at the rate of 0.6 W/ C.. Derate linearly to 50 C free air temperature at the rate of 2 mw/ C.. This rating is based on the capability of the transistor to operate safely in a circuit of: L = 20 mh, I B(on) = A, R BE = Ω, BE(off) = 0, R S = 0. Ω, CC = 20. CER CEO 55 70 90 5 5
, A, B, C electrical characteristics at 25 C case temperature (BR)CEO ES EO I EBO h FE CE(sat) BE h fe h fe PARAMETER TESONDITIONS MIN TYP MAX UNIT breakdown voltage cut-off current Collector cut-off current Emitter cut-off current Forward current transfer ratio saturation voltage Base-emitter voltage Small signal forward current transfer ratio Small signal forward current transfer ratio = 0 ma (see Note 5) CE = 55 CE = 70 CE = 90 CE =5 CE = 0 CE = I B = 0 BE =0 BE =0 BE =0 BE =0 I B =0 I B =0 A B C A B C /25A B/25C EB = 5 =0 ma CE = CE = CE = I B = I B = CE = CE = 0. A 2.5 A = A = A = 0 A = A = 0A = A = 0 A CE = 0 = 0.5 A f = khz 20 CE = 0 = 0.5 A f = MHz NOTES: 5. These parameters must be measured using pulse techniques, = 00 µs, duty cycle 2%. 6. These parameters must be measured using voltage-sensing contacts, separate from the current carrying contacts. 5 0 20 0.7 0.7.6 ma ma thermal characteristics PARAMETER MIN TYP MAX UNIT R θjc Junction to case thermal resistance.56 C/W R θja Junction to free air thermal resistance 2 C/W resistive-load-switching characteristics at 25 C case temperature PARAMETER TESONDITIONS MIN TYP MAX UNIT t on Turn-on time = A I B(on) = 0. A I B(off) = -0. A 0. µs t off Turn-off time BE(off) = -.7 R L = 20 Ω = 20 µs, dc 2% µs oltage and current values shown are nominal; exact values vary slightly with transistor parameters. 2
, A, B, C TYPICAL CHARACTERISTICS h FE - DC Current Gain 0 0 TYPICAL DC CURRENT GAIN COLLECTOR CURRENT CE = = 25 C = 00 µs, duty cycle < 2% TCS6AG CE(sat) - Collector-Emitter Saturation oltage - COLLECTOR-EMITTER SATURATION OLTAGE BASE CURRENT 0 0 TCS6AB = A = A = 6 A = 0 A 0 0 0 0 0 0 0 0 I B - Base Current - A Figure. Figure 2. BE - Base-Emitter oltage - 8 6 2 0 8 CE = = 25 C BASE-EMITTER OLTAGE COLLECTOR CURRENT TCS6AC 0 6 0 0 Figure.
, A, B, C MAXIMUM SAFE OPERATING REGIONS 0 0 MAXIMUM FORWARD-BIAS SAFE OPERATING AREA A B C 0 0 0 0 CE - Collector-Emitter oltage - Figure. THERMAL SAS6AC = 00 µs, d = 0. = 0% = ms, d = 0. = 0% = 0 ms, d = 0. = 0% DC Operation MAXIMUM POWER DISSIPATION CASE TEMPERATURE TIS6AA P tot - Maximum Power Dissipation - W 0 20 0 0 25 50 75 25 50 - Case Temperature - C Figure 5.
, A, B, C MECHANICAL DATA SOT-9 -pin plastic flange-mounackage This single-in-line package consists of a circuit mounted on a lead frame and encapsulated within a plastic compound. The compound will withstand soldering temperature with no deformation, and circuierformance characteristics will remain stable when operated in high humidity conditions. Leads require no additional cleaning or processing when used in soldered assembly. SOT-9,90,70 ø,,0 5,2,7,95,5,7,7 2,2 MAX. 6,2 MAX.,0 TYP. 8,0 TYP. 2,0,0 0,78 0,50, 0,8 2,50 TYP. ALL LINEAR DIMENSIONS IN MILLIMETERS NOTE A: The centre pin is in electrical contact with the mounting tab. MDXXAW 5