RF (Radio Frequency) C R Type (by) PhotoMOS RELAYS.±..69±.8.±..7±.8.±..8±.8 mm inch FEATURES. Low output capacitance between output terminals and low ON-resistance capacitance(c):.pf (typ.) ON resistance(r): 9.8Ω (typ.). High speed switching Turn on time: µs Turn off time: 6µs. SO package -pin type in super miniature design Size: (W). (L). (H). mm (W).69 (L).7 (H).8 inch. Low-level off state leakage current The SSR has an off state leakage current of several milliamperes, where as this PhotoMOS relay has only pa (typical) even with the rated load voltage. Controls low-level analog signals 6. Low thermal electromotive force (Approx. µv) TYPICAL APPLICATIONS Measuring and testing equipment. Testing equipment for semiconductor performance IC tester, Liquid crystal driver tester, semiconductor performance tester. Board tester Bear board tester, In-circuit tester, function tester. Medical equipment Ultrasonic wave diagnostic machine. Multi-point recorder (warping, thermo couple) TYPES Type AC/DC * Indicates the peak AC and DC values. Notes:. Tape package is the standard packing style. Also available in tube. (Part No. suffix X or Z is not needed when ordering Inner carton: pcs. Outer carton:, pcs.). For space reasons, the initial letters of the product number AQY and S, the package type indicator X and Z are omitted from the seal. RATING voltage rating* current V ma Picked from the /-pin side AQYNSX Tape and reel packing style Picked from the /-pin side AQYNSZ Tube, pcs. Packing quantity Tape and reel, pcs.. Absolute maximum ratings (Ambient temperature: C 77 F) Item LED forward current Symbol I F AQYNS ma Remarks Input LED reverse voltage V R V Peak forward current I FP A f = Hz, Duty factor =. % Power dissipation voltage (peak AC) P in V L 7 mw V Continuous load current I L. A Peak AC, DC Peak load current I peak. A ms ( shot), V L =DC Power dissipation Total power dissipation I/O isolation voltage P out P T V iso mw mw, V AC Temperature limits Operating T opr C to +8 C F to +8 F Non-condensing at low temperatures Storage T stg C to + C F to + F is the worldwide brand name of automation control products from Matsushita Electric Works.
. Electrical (Ambient temperature: C 77 F) Item Symbol AQYNS Condition Input LED operate current LED turn off current I Fon I Foff.9 ma. ma. ma.8 ma I L = ma I L = ma LED dropout voltage V F. V (.V at I F = ma). V I F = ma On resistance R on 9.8 Ω. Ω I F = ma I L = ma Within s on time capacitance C out. pf. pf I F = V B = V f = MHz Off state leakage current I Leak. na na I F = V L = Max. Transfer Switching speed I/O capacitance Turn on time* Turn off time* T on T off C iso. ms. ms.6 ms. ms.8 pf. pf I F = ma V L = V R L = Ω I F = ma V L = V R L = Ω f = MHz V B = Initial I/O isolation resistance R iso, MΩ V DC *Turn on/turn off time Input 9% % Ton Toff Other types of products than the C out (typ..pf) and R on (A connection typ. 9.8 ohm) combinations carried in this catalog are also available. (There is a trade-off between R on and C out both cannot be reduced at the same time.) For more information, please contact our sales office in your area.
REFERENCE DATA. current vs. ambient temperature Allowable ambient temperature: C to +8 C F to +8 F. On resistance vs. ambient temperature Measured portion: between terminals and. LED current: ma voltage: Max. (DC) Continuous load current: Max. (DC). Turn on time vs. ambient temperature LED current: ma voltage: Max. (DC) Continuous load current: Max. (DC). current, ma 8 6 On resistance, Ω Turn on time, ms.8.6.. 6 88. Turn off time vs. ambient temperature LED current: ma voltage: Max. (DC) Continuous load current: Max. (DC). 6 8 8. LED operate current vs. ambient temperature voltage: Max. (DC) Continuous load current: Max. (DC) 6 88 6. LED turn off current vs. ambient temperature voltage: Max. (DC) Continuous load current: Max. (DC) Turn off time, ms.8.6.. LED operate current, ma.. LED turn off current, ma.. 6 88 7. LED dropout voltage vs. ambient temperature LED current: to ma LED dropout voltage, V...... 6 88.. LED forward current vs. turn on time voltage: Max. (DC) Continuous load current: Max. (DC) Ambient temperature: C 77 F ma ma ma ma ma 6 88 8. Voltage vs. current of output at MOS portion Ambient temperature: C 77 F Current, ma 8 6........... Voltage, V 6 8. LED forward current vs. turn off time voltage: Max. (DC) Continuous load current: Max. (DC) Ambient temperature: C 77 F. 9. Off state leakage current Ambient temperature: C 77 F Off state leakage current, A 6 9. 6 88 voltage, V. Applied voltage vs. output capacitance Frequency: MHz, m Vrms Ambient temperature: C 77 F Turn on time, ms.. Turn off time, ms.8.6. capacitance, pf.... 6 LED forward current, ma 6 LED forward current, ma Applied voltage, V
. Isolation (Ω impedance) Ambient temperature: C 77 F Isolasion, db 8 6 6 7 8 Frequency, Hz. Insertion loss (Ω impedance) Ambient temperature: C 77 F Insertion loss, db.. 6 7 Frequency, Hz. On resistance distribution Continuous load current: ma(dc) = Ambient temperature: C 77 F 8.6 9 9. 9.8. On resistance, Ω 6. Turn on time distribution voltage: V(DC) Continuous load current: ma(dc) = Ambient temperature: C 77 F...6.8. Turn on time, ms 7. Turn off time distribution voltage: V(DC) Continuous load current: ma(dc) = Ambient temperature: C 77 F...6.8. Turn off time, ms 8. LED operate current distribution voltage: V(DC) Continuous load current: ma(dc) = Ambient temperature: C 77 F..8..6 LED operate current, ma DIMENSIONS mm inch.. Recommended mounting pad (Top view).±..7±.9 6.8±..68±.6 6...6.7.±..69±.9.±..79±.9...8.....6......6 Terminal thickness =..6 General tolerance: ±. ±. Tolerance:±. ±. SCHEMATIC AND WIRING DIAGRAMS Schematic configuration Wiring diagram a AC/DC E IF IL VL (AC,DC) IL VL (AC,DC)
CAUTIONS FOR USE. Short across terminals Do not short circuit between terminals when relay is energized, since there is the possibility of breaking the internal IC.. Surge voltages at the input If reverse surge voltages are present at the input terminals, connect a diode in reverse parallel across the input terminals and keep the reverse voltages below the reverse breakdown voltage. Emin.. Recommended LED forward current (IF) It is recommended that the LED forward current (IF) should be kept at ma.. Ripple in the input power supply If ripple is present in the input power supply, observe the following: ) For LED operate current at E min, maintain the value mentioned in the table of Note. Recommended LED forward current (IF). ) Keep the LED operate current at ma or less at E max. Emax.. spike voltages ) If an inductive load generates spike voltages which exceed the absolute maximum rating, the spike voltage must be limited. circuits are shown below. Add a clamp diode to the load Add a CR snubber circuit to the load ) Even if spike voltages generated at the load are limited with a clamp diode if the circuit wires are long, spike voltages will occur by inductance. Keep wires as short as possible to minimize inductance. 6. Cleaning solvents compatibility Dip cleaning with an organic solvent is recommended for removal of solder flux, dust, etc. Select a cleaning solvent from the following table. If ultrasonic cleaning must be used, the severity of factors such as frequency, output power and cleaning solvent selected may cause loose wires and other defects. Make sure these conditions are correct before use. For details, please consult us. Adueous Chlorinebase Alcoholbase Others Cleaning solvent I.I.I. Trichloroethlene (Chloroethlene) Trichloroethlene (Trichlene) Perchloroethlene Methlene chloride Indusco 6, Hollis Lonco Terg IPA Ethanol Thinner Gasoline Compatibility : Yes ( : No ) 7. Input wiring pattern This relays, avoid installing the input (LED side) wiring pattern to the bottom side of the package if you require the specified I/O isolation voltage (Viso) after mounting the PC board. Since part of the frame on the output side is exposed, it may cause fluctuations in the I/O isolation voltage. Portion of output side frame ( terminal side) Input wiring pattern (Input terminal side) May not allow the prescribed I/O withstand voltage (Viso) to be achieved 8. Soldering When soldering this terminals, the following conditions are recommended. () IR (Infrared reflow) soldering method T T T t T = to 6 C to 9 F T = 8 C C 6 to 9 F T = C 7 F or less t = s or less t = s or less () Vapor phase soldering method T T t T = 8 to C 66 to 9 F T = C 9 F or less t = s t = s or less () Double wave soldering method T T T = to 6 C to 9 F T = 6 C F or less t = 6 s or less t+t = s or less t t t t t () Soldering iron method Tip temperature: 8 to C 6 to 7 F Wattage: to 6 W Soldering time: within s () Others Check mounting conditions before using other soldering methods (hot-air, hot plate, pulse heater, etc.) The temperature profile indicates the temperature of the soldered terminal on the surface of the PC board. The ambient temperature may increase excessively. Check the temperature under mounting conditions. The conditions for the infrared reflow soldering apply when preheating using the VPS method.
9. The following shows the packaging format ) Tape and reel mm inch Type Tape dimensions Dimensions of paper tape reel SO package -pin type Tractor feed holes.±. dia..±..6±. dia..±. Device mounted on tape.8±..±. ±..7±. Direction of picking 7.±..8±. ±..7±. ±..79±..7±..69±..±..7±..7±. ±..8±..7±..±. dia..6±. dia. ±..79±. ±.8.87±. 8± dia..±.9 dia. ± dia. 9.8±.79 dia. 8± dia..±.9 dia. () When picked from /-pin side: Part No. AQY SX (Shown above) () When picked from /-pin side: Part No. AQY SZ ±. dia..±. dia. ±..±.9 ±..79±. (SOP type) StopperB (green) ) Tube () Devices are packaged in a tube so pin No. is on the stopper B side. Observe correct orientation when mounting them on PC boards. () Storage StopperA (gray) PhotoMOS relays implemented in SO packages are sensitive to moisture and come in sealed moisture-proof packages. Observe the following cautions on storage. After the moisture-proof package is unsealed, take the devices out of storage as soon as possible (within month at the most). If the devices are to be left in storage for a considerable period after the moisture-proof package has been unsealed, it is recommended to keep them in another moisture-proof bag containing silica gel (within months at the most).. Transportation and storage ) Extreme vibration during transport will warp the lead or damage the relay. Handle the outer and inner boxes with care. ) Storage under extreme conditions will cause soldering degradation, external appearance defects, and deterioration of the. The following storage conditions are recommended: Temperature: to C to F Humidity: Less than 7% R.H. Atomosphere: No harmful gasses such as sulfurous acid gas, minimal dust.. Matsushita Electric Works Group Europe