Bushless version P- FETURES mm arbon Potentiometer arbon resistive element Dust proof enclosure Polyester substrate Modular gang type (up to ) Self extinguishable material U -V0 Upon request: Metalic support Stereo matching Switch Nut & washer Bushless option available MEHNI SPEIFITIONS Mechanical rotation angle: 00 ± Electrical rotation angle: ± Torque: 0. to. Ncm. (0.7 to 2. in-oz) Stop torque: > 0 Ncm. ( > in-oz) Max. torque nut (binding out): < 0 Ncm. ( in-oz) Thrust and pull in the shaft: > 2 N EETRI SPEIFITIONS Range of values (*) Tolerance (*): ± % ± 0% Max. Voltage: VD (lin) VD (no lin) Nominal Power 0 (2 F) (see power rating curve) 0.2 W (lin) 0. W (no lin) Taper (*) (og. & log. only Rn > K) in ; og; log. Residual resistance: Equivalent Noise Resistance: Operating temperature**: 2 + 70 ( F + F) * Others upon request ** Up to depending on application HOW TO ORDER STNDRD OPTION EXTRS P- D H I M0 0 Serie P- Model S =Single D =Tandem T =Triple =Quad. NOTES: QS 000 ertificate Nº 77 Mounting style H= Horizontal V = Vertical (See note ) Bushing diameter 07 = M7 = M S = Bushless (See note 2) ISO 0 ertificate Nº Terminals I = PB = Solder ugs Shafts M0 M0 M07 M M7 P0 P22 --- (See note ) Value (See note ) Taper = inear B = og. = log. (See note ) Others tapers on request NOTE: The information contained here should be used for reference purposes only. 7 Tolerance = +/- % 00 = +/- 0% (See note ) Shafts spec. leng. XX.X (See notes,) Mounting brackets M M2 (See note 7) Stereo matching D = db D = db D = db (See note ) Switch I = PB = Solder lugs (See note ) Nuts & Washers -T = loose nut & washer MT=assembled nut & washer -T- = loose nut MT- = assembled nut (See note ) () Mounting style: Type "V" is only available in model "S" potentiometer and with printed circuit terminals. (2) Bushings: Type "" has two paralell flat surfaces for avoiding rotation. Bushless option only available for single model. () M07 shaft is only available with M bushing. --- = no shaft () Value: ode: Number of zeros 2 first digits of the value. In models "D", "T", "", with different values, they will be asked by drawings. () Tolerance (non standard), upon request. Example: +7% ode: 07 0 -% negative tolerance () Shaft special length: positive tolerance Only for special length and plain shafts (not knurled). Example: Shaft Ø. = 2. M07... 2. NOTE: Maximun length recommended: = (7) Mounting brackets: Only applicable for model "S", mounting "H" and without switch. special length shafts () Stereo matching: not available for single models. Maximun will be: db for model "D" db for model "T" db for model "" () Not available for Bushless version. () Switch option not available with antilog taper.
HOW TO ORDER USTOM DRWING P- S V + DRWING NUMBER (Max. digits) This way of ordering should be used for options which are not included in the "How to order" standard and optional extras. MODES M x 0.7. 7. 7. 7.. E S. STNDRD OPTIONS Shaft length... 0 Standard ength Mounting brackets... Without mounting brackets Stereo matching... Only on request (see note ) Switch... No switch Nut & washer... Without nut and washer PIHE M x 0.7 S E.. +0. 0. +0. +0.. 7. 7. 7. = Initial S = Wiper E = Final. +0.. +0. S D T P- S/D/T/..H... P- SV... METI SUPPORT. 2. 7. -0... +0. P- SH...M P- SH...M2 0. M x 0.7. M x 0.7. M x 0.7.. +0.. 2. 7... +0.. +0. BUSHINGS 0. M7 x 0.7 07 7 EXMPES OF BUSHESS VERSION 7. 7. 7.. thickness = 0. 7
TERMINS Hole for heat dissipation Hole for heat dissipation +0. 2. -0.0. 2. I TPERS POWER RTING URVE NUTS & WSHERS Standard Bushing Bushing 07 0 0 0 0 0 B = inear B = og. = log. E 2 0 7 0 0 % 0 % W (%) 0 70 2. 0. M x 0.7. 2. 0. M7 x 0.7. 7.2 NOTE = Please note relative terminal positions when ordering non linear tapers. TESTS EETRI IFE MEHNI IFE : POT. SWITH.000 h. @ 0 ; 0.2 W 2.000 (- PM).000 (, 0 V) TYPI VRITIONS ± % ± % (Rn < M ) SWITH. PB TERMIN -0.2 M x 0.7.. +0. +0.2. SODER UG TERMIN +0.. +0. TEMPERTURE OEFFIIENT 2 ; +70 ±00 ppm/ O (Rn <0 K ) THERM YING DMP HET VIBRTION (for each plane X,Y,Z) h. @ ; 2h. @ 2 00 h. @ 0 @ % HR 2 h. @ Hz.... Hz. ±2. % ± % ±2 % M x 0.7.. P-S... H... I / +0.. P-SV... I 7
SWITH SPEIFITIONS NOMIN URRENT ONTT RESISTNE (initial) OPERTING TORQUE OPERTING NGE TEST VOTGE PKGING Boxes of 0 pieces ( x x mm.) METI SHFTS STNDRD ODE M0 M0 +0.. M07 B ODE B 2 7 M 2 M 2 M 0 M M 0 M SPEI M7.2 +0. +0.. PSTI SHFTS Ø.. 0 o 0 o 7. +0. 7 +0. +0. P0 P02 P0 7
PSTI SHFTS Ø o 22,. +0. P0 +0. P0. 0 o.2 +0. P. 7 o 2 +0. P 27. +0. o P.. 2 +0. P 2. +0. P ±0. P7 0 +0. +0. P0 P0 7 o.7 2. 0 o +0.. P0 7 +0. P.7 +0. P2 PSTI SHFTS Ø 7 +0. 0 o P07. 2. +0. 0 o P. +0. P +0. P. +0. P NOTE: Shaft position shown full W. ny other position for plastic shafts has to be shiftted n times 2 Other positions upon request.. 2 ±0. P22 77