ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8-0 Fax +9 798 8-0 info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen Amtsgericht (court of registration) Stuttgart HRA 590 General partner Elektrobau Mulfingen GmbH Headquarters Mulfingen Amtsgericht (court of registration) Stuttgart HRB 590 Nominal data Type Motor WS0-AA0- MS05-CA Phase ~ ~ ~ Nominal voltage VAC Frequency Hz Method of obtaining data fa fa fa Valid for approval/standard CE CE UL Speed (rpm) min - 800 Power consumption W 5 9 9 Current draw A 0.5 Max. back pressure Pa 80 0 0 Max. back pressure inho 0. 0.8 0.8 Min. ambient temperature C -5-5 -5 Max. ambient temperature C 70 70 Starting current A 0.5 0.0 ml = Max. load me = Max. efficiency fa = Free air cs = Customer specification ce = Customer equipment Subject to change Item no. 60-5-9980 ENU Change 8988 Approved 06-0-9 Page / 5
Technical description Weight Fan size Rotor surface Blade material Fan housing material Number of blades 7 Airflow direction Direction of rotation Degree of protection Insulation class Max. permitted ambient temp. for motor (transport/storage) Min. permitted ambient temp. for motor (transport/storage) Installation position Condensation drainage holes Mode Motor bearing Touch current according to IEC 990 (measuring circuit Fig., TN system) Electrical hookup Motor protection Protection class Conformity with standards Approval. kg 0 mm Rotor open, painted black Sheet steel, painted black Die-cast aluminum, painted black "V" Counterclockwise, viewed toward rotor IP0 "B" + 80 C - 0 C Any None, open rotor S Ball bearing < 0.75 ma With plug Thermal overload protector (TOP) internally connected I (if protective earth is connected by customer to the housing's connection point) CE UL 7; CSA C. No. ; VDE Item no. 60-5-9980 ENU Change 8988 Approved 06-0-9 Page / 5
Product drawing Direction of air flow "V" Connector housing with x flat plugs.8 x 0.5 mm M screw for fastening ground connector Connection diagram L N TOP = black = black = thermal overload protector Item no. 60-5-9980 ENU Change 8988 Approved 06-0-9 Page / 5
Curves: Air performance Hz Pfs Pa 0 0 0 0 in wg 0.05 0. 0.5 0. 0.5 0 0 80 0 00 00 00 ρ =.5 kg/m³ ± % cfm m³/h Measurement: LU-5875- Air performance measured according to ISO 580 installation category A. For detailed information on the measurement setup, contact ebm-papst. Intake sound level: Sound power level according to ISO 7 / sound pressure level measured at m distance from fan axis. The values given are valid under the specified measuring conditions and may vary due to conditions of installation. For deviations from the standard configuration, the parameters have to be checked on the installed unit. Measured values U V f Hz n min - 800 795 780 780 P e W 5 5 6 6 I A m /h 0 05 65 00 Pa 0 0 0 55 CFM 00 80 55 0 inho 0.00 0.08 0.6 0. U = Power supply f = Frequency n = Speed (rpm) P e = Power consumption I = Current draw = Air flow = Pressure increase Item no. 60-5-9980 ENU Change 8988 Approved 06-0-9 Page / 5
Curves: Air performance Hz Pfs Pa 80 0 0 0.05 0. 0.5 0. 0.5 0. in wg 0 0 80 0 00 00 00 00 cfm m³/h ρ =.5 kg/m³ ± % Measurement: LU-5876- Air performance measured according to ISO 580 installation category A. For detailed information on the measurement setup, contact ebm-papst. Intake sound level: Sound power level according to ISO 7 / sound pressure level measured at m distance from fan axis. The values given are valid under the specified measuring conditions and may vary due to conditions of installation. For deviations from the standard configuration, the parameters have to be checked on the installed unit. Measured values U V f Hz n min - 00 65 5 P e W 9 I A 0.5 0.5 0.6 0.6 m /h 90 55 05 5 Pa 0 5 70 CFM 0 80 5 inho 0.00 0.0 0.0 0.8 U = Power supply f = Frequency n = Speed (rpm) P e = Power consumption I = Current draw = Air flow = Pressure increase Item no. 60-5-9980 ENU Change 8988 Approved 06-0-9 Page 5 / 5