Flow control on a 3D backward facing ramp by pulsed jets

Transcription

1 Acknowledgements: This work was carried out in the framework of the FOSCO project, supported by ic ARTS Flow control on a 3D backward facing ramp by pulsed jets 3 rd GDR Symposium P. Joseph a, D. Bortolus a, F. Grasso a b a Institut AéroTechnique (IAT-CNAM), 15 rue Marat, Saint-Cyr-l Ecole (France) b CNAM, Laboratoire DynFluid, 151 Boulevard de l'hôpital, Paris (France) pierric.joseph@cnam.fr

2 FOSCO Project Introduction «FOrcing for Separation COntrol» Sequel of CARAVAJE project (flow control by pulsed jets applied to automotive vehicles) Objective: comprehension of the physical mechanisms associated with periodic forcing Test case: simple geometry but close to industrial preoccupations 2

3 Experimental setup Test case Wind tunnel arrangement Instrumentation Base flow characterization Mean flow topology Mean pressure distribution Incoming flow characterization PIV investigations Flow control experiments Control strategy Control system Jets characterization Parametric study Mean flow modifications Conclusions and perspectives Summary 3

4 Experimental setup Test case : the 3D backward facing ramp Why not the classical Ahmed body? Classical 25 slant angle Ahmed body (Ahmed et al. 1984) Critical, bi-stable angle High drag case unfavorable Underbody without moving floor Etc. Geometry well adapted for control studies related to notchback configuration 4

5 Wind tunnel arrangement Experimental setup Automotive wind tunnel (S4) with test chamber of 5 m x 3 m, U 0 up to 44 m.s -1 and turbulence intensity 1.2% Model installed on raised floor to deal with the natural boundary layer of the wind tunnel Model Naca 0018 leading edge Additional instrumented area on the raised floor due to the expected flow topology Expected flow topology 5

6 Instrumentation PIV system (2D2C 2D3C) Experimental setup 200 mj, 15Hz Nd:YAG Laser 4 Mpx cameras Seeding with oil droplets (2µm) Adaptive correlation algorithm 16 x 16 pixels with 50% overlap Steady pressure measurements Flow symmetric in the mean 141 pressure taps on half of the model Scanivalve pressure scanner Accuracy: 0.03% Results expressed as pressure coefficient: 6

7 Experimental setup Test case Wind tunnel arrangement Instrumentation Base flow characterization Mean flow topology Mean pressure repartition Incoming flow characterization PIV investigations Flow control experiments Control strategy Control system Jets characterization Parametric study Mean flow modifications Conclusions and perspectives Summary 7

8 Base flow characterization Mean Flow topology Oil flow visualizations* at Re L = 1.4 x 10 6 (U 0 = 20 m.s -1 ) Flow pattern reconstructed through friction lines Flow pattern proposed by Gilhome et al. (2006) Similar flow pattern with notchback car *dodecan, silicon oil, oleic acid and titanium oxide 8

9 Base flow characterization Mean pressure distribution Pressure coefficient (C p ) iso-contours (Re L = 1.4 x 10 6 ; U 0 = 20 m.s -1 ) Print of the mean recirculation area Lack of information regarding side regions (both for the top and the lateral edges of the slant) 9

10 Z (mm) Base flow characterization Incoming flow characterization Boundary layer measurement at X = - 5 x 10-2 m, Y = 9.5 x 10-2 m Re L = 1.4 x 10 6 (U 0 = 20 m.s -1 ) Exp. Data Th. model (1/7 power law) δ 99 = 26 x 10-3 m δ* = 2.8 x 10-3 m θ = 2.3 x 10-3 m H = 1.24 Measurements location u/u 0 Similarities with the boundary layer developing on the roof of the Ahmed body 10

11 PIV investigations Base flow characterization Longitudinal plane (Y = 0, Re L = 1.4 x 10 6, U 0 = 20 m.s -1 ) L R L R 0.26 m, independent from Reynolds number but strongly affected by edge sharpness 11

12 PIV investigations Base flow characterization Transversal plane (X = m, Re L = 1.4 x 10 6, U 0 = 20 m.s -1 ) Ramp location (U 2 Y + U Z2 ) 1/2 (m.s -1 ) Vortex core location independent from Reynolds number 12

13 Experimental setup Test case Wind tunnel arrangement Instrumentation Base flow characterization Mean flow topology Mean pressure repartition Incoming flow characterization PIV investigations Flow control experiments Control strategy Control system Jets characterization Parametric study Mean flow modifications Conclusions and perspectives Summary 13

14 Control strategy Flow control experiments Objective: suppression or reduction of the mean recirculation area Introduction of counter - rotating vortex pairs (CRV) Jet in cross flow (Cortelezzi & Karagozian 2001) Passive vortex generators (Duriez et al. 2009) Momentum transfer between free flow and low velocity area CRV created through pulsed jets Dynamic vortex generators (Ortmanns et al. 2008) 14

15 Control system Flow control experiments Pulsed jets produced by magnetic valves (see Joseph et al. 2012) Valves driven by TTL (rectangular, 0 5V) signal with variable frequency and duty cycle 89 rectangular jets located at X = - 1 x 10-2 m upstream of the separation point 15

16 Flow control experiments Jets characterization Strong variations of spatio-temporal characteristics with the command parameters: supply pressure p S, duty cycle DC and command frequency f J Hot wire measurements with 1D probe at Z = 1 x 10-3 m 16

17 Flow control experiments Mean flow modifications Parametric study (Cµ, St J and U 0 ) Monitoring of pressure recovery on a single point Re L = 1.4 x 10 6 (U 0 = 20 m.s -1 ) p S = 6 bar Addional measurements Interaction with flow instabilities? Special functioning mode of the actuators? 190 Hz implies only overshoot on the temporal history of the jet velocity 17

18 Flow control experiments Mean flow modifications PIV measurements (XZ plane, Y = 0, Re L = 1.4 x 10 6, U 0 = 20 m.s -1 ) Cμ = 19 x 10-3, St J = 0.89 and DC = 50% Controlled flow Base flow Suppression of the recirculation area 18

19 Flow control experiments Mean flow modifications Pressure coefficient C p mapping (Re L = 1.4 x 10 6, U 0 = 20 m.s -1 ) Cμ = 19 x 10-3, St J = 0.89 and DC = 50% Controlled flow Base flow Global pressure recovery but lack of information on the side area (low pressure expected) C X? 19

20 Flow control experiments Mean flow modifications PIV measurements (YZ plane, X = m, Re L = 1.4 x 10 6, U 0 = 20 m.s -1 ) Cμ = 19 x 10-3, St J = 0.89 and DC = 50% Controlled flow Base flow Displacement of vortex cores location and increase in size Additional flow structures : Görtler vortices? 20

21 Flow control experiments Mean flow modifications PIV measurements (YZ plane, X = m, Re L = 1.4 x 10 6, U 0 = 20 m.s -1 ) Cμ = 19 x 10-3 St J = 0.83 DC = 50% St J = 0.28 DC = 50% Strong influence of the actuation frequency on the additional flow structure (still under investigation) 21

22 Conclusions Base flow consistent with wake of a notchback automotive Separated bulb along with pair of longitudinal vortices Control action leads to reattachment Pressure increases globally, but effect on C X still to be adressed Control action mainly driven by actuator characteristics rather than by interaction with flow instabilities However local influence on mean flow topology 22

23 Perspectives Unsteady measurements C X evaluation through conservation of momentum Numerical simulation (research code developed for DNS with high order resolution) Instantaneous Q criterion (Re L = 1.4 x 10 6 ) Preliminary numerical results (isosurface U/U 0 = 0.88, Re L = 2.1 x 10 6 ) 23

24 References Ahmed, S., Ramm, G. & Faltin, G., Some Salient Features of the Time-Averaged Ground Vehicle Wake. SAE Cortelezzi, L. & Karagozian, A.R., On the formation of the counter-rotating vortex pair in transverse jets. Journal of Fluid Mechanics, 446, pp Duriez, T., Aider, J.-L. & Wesfreid, J.-E., Self-Sustaining Process through Streak Generation in a Flat-Plate Boundary Layer. Physical Review Letters, 103(14). Gilhome, B., Saunders, J. & Sheridan, J., Time Averaged and Unsteady Near-Wake Analysis of Cars. SAE Technical Paper Joseph, P., Amandolèse, X. & Aider, J.-L., Drag reduction on the 25 slant angle Ahmed reference body using pulsed jets. Experiments in Fluids, 52(5), pp Ortmanns, J., Bitter, M. & Kähler, C.J., Dynamic vortex structures for flow-control applications. Experiments in Fluids, 44(3), pp