S-7000 ROTARY CODED SWITCHES (SMD) S E T A FEATURES PART NUMBER DESIGNATION. Please refer to the LIST OF PART NUMBERS when placing orders.

Transcription

1 S- RoHS compliant INTERNL STRUCTURE Part name Material lammability ETURES Cover Stainless steel (SUS ) O ring Rotor Spacer Moving contact ixed contact Silicone rubber Polyphenylenesulphide Stainless steel (SUS ) Copper alloy, Gold-plated ULHB ULV- Housing Epoxy ULV- Terminal pin Copper alloy, Gold-plated PRT NUMBER DESIGNTION S - E T Series name Shape of rotor Without knob Code format positions, real code positions, complementary code positions, real code positions, real code positions, complementary code Setting position Top setting Side setting Except for positions type orm of packaging Shape of terminal J-hook BGull wing CThrough hole pins Except for positions type TTaping (Reel) WTray packaging (Through hole pins only) BlankBulk in plastic bag Terminal pin Eu () Please refer to the LIST O PRT NUMBERS when placing orders.

2 S- CODE ORMT Code positions No. of positions positions positions Position Real code Complementary code Contact closed LIST O PRT NUMBERS Setting position Shape of terminal orm of packaging Binary coded hexal Real code Binary coded decimal Real code Complementary code Binary coded hexadecimal Real code Complementary code Pieces in package J-hook) Taping S-ET S-ET S-ET S-ET S-ET pcs. / reel S-E S-E S-E S-E S-E pcs. / pack Top setting B Gull wing) Taping S-ETB S-ETB S-ETB S-ETB S-ETB pcs. / reel S-EB S-EB S-EB S-EB S-EB pcs. / pack C Through hole pin) Tray packaging S-EWC S-EWC S-EWC S-EWC pcs. / tray S-EC S-EC S-EC S-EC pcs. / pack J-hook) Taping S-ET S-ET S-ET S-ET pcs. / reel S-E S-E S-E S-E pcs. / pack Side setting B Gull wing) Taping S-ETB S-ETB S-ETB S-ETB pcs. / reel S-EB S-EB S-EB S-EB pcs. / pack C Through hole pin) Tray packaging S-EWC S-EWC S-EWC S-EWC pcs. / tray S-EC S-EC S-EC S-EC pcs. / pack Not manufactured Verify the above part numbers when placing orders. Taping and tray version can be supplied only in reel or tray unit. The products indicated by mark are manufactured upon receipt of order basis.

3 S- STNDRD SPECIICTIONS ELECTRICL CHRCTERISTICS Circuit type Operating temperature range Storage temperature range BCD (Real code, complementary code) BCH (Real code, complementary code) ~ C Contact rating Non-switching Switching Minimum DC V m DC V m DC mv μ Contact resistance mω maximum Sealing Washable by O ring Please refer to page, Insulation resistance MΩ (DC V) minimum Net weight pprox.. g ( or B type in top setting) pprox.. g (C type in top setting) pprox.. g (Side setting type) Dielectric strength C V, s MECHNICL CHRCTERISTICS ENVIRONMENTL CHRCTERISTICS No. of positions djustment torque,, mn m { gf cm} maximum Vibration (mplitude). mm or (cceleration) m/s, -- Hz, directions for h each Stepping angle Solderability Soldering heat ( positions) ( positions). ( positions) ± C, ~ s Reflow C (Peak temperature) Please refer to the profile below low : ± C, ~ s, two times maximum Manual soldering : ± C, ~ s Shock Load life Humidity (Steady state) High temperature exposure Low temperature exposure m/s, ms directions for times each steps minimum, DC V, m C,Relative humidity ~ %, h C, h C, h Shear (adhesion) N {. kgf}, s Thermal shock (. h) ~ C (. h ), cycles Substrate bending Width mm, bend mm, s, time Pull-off strength N {. kgf}, s { } : Reference only Reflow profile for soldering heat evaluation Temperature () + Peak : Over Pre Heating Zone ± s ± s Heating time Soldering Zone Reflow : two times maximum

4 S- OUTLINE DIMESIONS S-E (Real code) S-E (Complementary code) Unless otherwise specified, tolerance: ±. (Unit: mm) S-E (Real code) S-E (Complementary code) C. W. L. D. t =. C. W. L. D. t = C.... C.... S-EB (Real code) S-EB (Complementary code) S-EB (Real code) S-EB (Complementary code) C. W. L. D. min.. t =. C. W. L. D. min.. t =..... C. min..... C.. min.... S-EC (Real code) S-EC (Complementary code) S-EC (Real code) S-EC (Complementary code) C. t =. C. t =..... C W. L. D Projection. C.. W. L. D Projection.....

5 S- OUTLINE DIMESIONS S-E (Real code) S-E (Complementary code) Unless otherwise specified, tolerance: ±. (Unit: mm) S-E (Real code) S-E (Complementary code) C. W. L. D min... t =... C. W. L. D min... t =..... C min. C min. S-EB (Real code) S-EB (Complementary code) S-EB (Real code) S-EB (Complementary code) C. W. L. D. min... t =... C. W. L. D. min... t =..... C. min. C. min. S-EC (Real code) S-EC (Complementary code) S-EC (Real code) S-EC (Complementary code) C. W. L. D... t =... C. W. L. D... t =... C C

6 S- OUTLINE DIMESIONS S-E (Real code) Unless otherwise specified, tolerance: ±. (Unit: mm) S-EB (Real code) C. t =. C. min.. t =. RECOMMENDED P.C.B. PD OUTLINE DIMENSIONS <Top setting> type. B type (Unit: mm) φ. φ NO C..... W. L. D NO C. min W. L. D <Side setting> type B type SIZE O P.C.B. PROCESSING <Top setting> C type <Side setting> C type Operating face....

7 S- PCKGING SPECIICTIONS <Taping packaging specifications> Reel dimensions (Conforms to JIS C -) (In accordance with EIJ ET-) (Unit: mm) Empty illed Empty. End mm min. pitches min. mm min. Head... min. (Top setting type) (Side setting type) (Top setting type) (Side setting type).

8 S- S-ET <Top setting> <Side setting> (Conforms to JIS C -) (Unit: mm) ±. D E ±. ±. φ. +..±..±..±. ±. ±. ±. φ. +..±..±...±. B. S-ETB < Top setting > <Side setting> ±. D E ±. ±. φ. +..±..±..±. ±. ±. ±. φ. +...±. C C.±..±. B. <Tray packaging specifications> <Bulk pack specifications>