Known: long, aluminum cylinder acts as an extended surface.

Size: px
Start display at page:

Download "Known: long, aluminum cylinder acts as an extended surface."

Transcription

1 Prolem : A long, irular aluminium rod attahed at one end to the heated all and transers heat through onvetion to a old luid. (a) I the diameter o the rod is triples, y ho muh ould the rate o heat removal hange? () I a opper rod o the same diameter is used in plae o aluminium, y ho muh ould the rate o heat removal hange? Knon: long, aluminum ylinder ats as an extended surae. Find: (a) inrease in heat transer i diameter is tripled and () inrease in heat transer i opper is used in plae o aluminum. Shemati: T, h Aluminum Or opper D Assumptions: () steady-state onditions, () one-dimensional ondution, (3) onstant properties, (4) uniorm onvetion oeiient, (5)rod is ininitely long. Properties: aluminum (pure): k=40w/m. K; opper (pure): k=400w/m. K Analysis: (a) or an ininitely long in, the in rate is r = M = ( hpka ) θ = ( hπdkπd / 4) θ π = ( hk) D 3 θ Where P=πD and A =πd /4 or the irular ross-setion. Note that D 3 /. Hene, i the diameter is tripled, (3D) ( D) = 3 3 = 5. And there is a 50 % inrease in heat transer.

2 () in hanging rom aluminum to opper, sine k /, it ollos that ( ) Cu k 400 Cu = = ( ) Al k Al 40 =.9 And there is a 9 % inrease in the heat transer rate. Comments: () eause in eetiveness is enhaned y maximum P/A = 4/D. the use o a larger numer o small diameter ins is preerred to a single large diameter in. () From the standpoint o ost and eight, aluminum is preerred over opper.

3 Prolem : To long opper rods o diameter D= m are soldered together end to end, ith solder having melting point o C. The rods are in the air at 50C ith a onvetion oeiient o 0W/m. K. What is the minimum poer input needed to eet the soldering? Knon: Melting point o solder used to join to long opper rods. Find: Minimum poer needed to solder the rods. Shemati: Copper D=m Juntion T =650 0 C Air T = 5 0 C H=0W/m. K Assumptions: () steady-state onditions, () one-dimensional ondution along the rods, (3) onstant properties, (4) no internal heat generation, (5) negligile radiation exhange ith surroundings, (6) uniorm, h and (7) ininitely long rods. Properties: opper T = (650+5) 0 C 600K: k=379 W/m.K Analysis: the juntion must e maintained at C hile energy is transerred y ondution rom the juntion (along oth rods). The minimum poer is tie the in heat rate or an ininitely long in,

4 = = (hpka ) (T T ) min sustituting numerial values, W = 0 (π 0.0m) 379 min m.k thereore, min = 0.9W W m.k π (0.0m) 4 (650 5) 0 C. Comments: radiation losses rom the rod are signiiant, partiularly near the juntion, therey reuiring a larger poer input to maintain the juntion at C.

5 Prolem 3: Determine the perentage inrease in heat transer assoiated ith attahing aluminium ins o retangular proile to a plane all. The ins are 50mm long, 0.5mm thik, and are eually spaed at a distane o 4mm (50ins/m). The onvetion oeiient aeted assoiated ith the are all is 40W/m. K, hile that resulting rom attahment o the ins is 30W/m. K. Knon: Dimensions and numer o retangular aluminum ins. Convetion oeiient ith and ithout ins. Find: perentage inrease in heat transer resulting rom use o ins. Shemati: L=50mm N=50m - W=idth h = 30W/m.K(ith ins) h o =40W/m.K(ithout ins) Aluminium Assumptions: () steady-state onditions, () one-dimensional ondution, (3) onstant properties, (4) negligile in ontat resistane, (6) uniorm onvetion oeiient. Properties: Aluminum, pure: k 40W/m. K Analysis: evaluate the in parameters L = L + A L L 3/ p 3/ = L t = m (h (h / KA / KA t = m max / P ) / P ) it ollos that, η = = η = 0.7h (0.0505m) = hene Lθ 3/ m = = W / m.k 0.05m (θ 3 30W / m.k 40W / m.k ) = 6 m.6w / m / 6 m K(θ / )

6 With the ins, the heat transer rom the alls is = N + ( Nt)h θ W 4 = 50.6 (θ ) + (m m) 30W / m.k(θ m.k W = ( ) (θ ) = 566θ m.k = h m θ = 40θ Without the ins,. o Hene the perentage inreases in heat transer is o ) o 566θ = 40θ = 4.6 = 46% Comments: I the inite in approximation is made, it ollos that = / (hpka ) θ = [h kt] / θ = (30**40*5*0-4 ) / θ =.68 θ. Hene is overestimated.

Module 3, Learning Objectives:

Module 3, Learning Objectives: Heat and Mass Transer Pro. Pradip Dutta Module 3, Learning Ojetives: Students should reognize the in euation. Students should know the general solutions to the in euation. Students should e ale to write

More information

Part G-4: Sample Exams

Part G-4: Sample Exams Part G-4: Sample Exams 1 Cairo University M.S.: Eletronis Cooling Faulty of Engineering Final Exam (Sample 1) Mehanial Power Engineering Dept. Time allowed 2 Hours Solve as muh as you an. 1. A heat sink

More information

PERFORMANCE EVALUATION OF WIRE SPRING FIN FOR COMPACT PLATE-FIN HEAT EXCHANGERS

PERFORMANCE EVALUATION OF WIRE SPRING FIN FOR COMPACT PLATE-FIN HEAT EXCHANGERS Proeedings o Fith International Conerene on Enhaned, Compat and Ultra-Compat Heat Exhangers: Siene, Engineering and ehnology, Eds. R.K. Shah, M. Ishizuka,.M. Rudy, and V.V. Wadekar, Engineering Conerenes

More information

EFFECT OF PERFORATION AREA ON TEMPERATURE DISTRIBUTION OF THE RECTANGULAR FINS UNDER NATURAL CONVECTION

EFFECT OF PERFORATION AREA ON TEMPERATURE DISTRIBUTION OF THE RECTANGULAR FINS UNDER NATURAL CONVECTION RPN Journal o Engineering and pplied Sienes 2006-2016 sian Researh Publishing Network (RPN). ll rights reserved. www.arpnjournals.om EFFECT OF PERFORTION RE ON TEMPERTURE DISTRIBUTION OF THE RECTNGULR

More information

International Journal of Modern Trends in Engineering and Research e-issn No.: , Date: 2-4 July, 2015

International Journal of Modern Trends in Engineering and Research   e-issn No.: , Date: 2-4 July, 2015 International Journal o Modern Trends in Engineering and Researh www.ijmter.om e-issn No.:2349-9745, Date: 2-4 July, 2015 Numerial Analysis And Parametri Study o Miro-hannel Heat Exhanger For Single Phase

More information

Practice Exam 2 Solutions

Practice Exam 2 Solutions MASSACHUSETTS INSTITUTE OF TECHNOLOGY Department o Physis Physis 801T Fall Term 004 Problem 1: stati equilibrium Pratie Exam Solutions You are able to hold out your arm in an outstrethed horizontal position

More information

PROBLEM 3.10 KNOWN: Dimensions and surface conditions of a plate thermally joined at its ends to heat sinks at different temperatures. FIND: (a) Differential equation which determines temperature distribution

More information

EXTENDED SURFACES / FINS

EXTENDED SURFACES / FINS EXTENDED SURFACES / FINS Convection: Heat transer etween a solid surace and a moving luid is governed y the Newton s cooling law: q = ha(t s -T ). Thereore, to increase the convective heat transer, one

More information

EFFECT THE FORM OF PERFORATION ON THE HEAT TRANSFER IN THE PERFORATED FINS

EFFECT THE FORM OF PERFORATION ON THE HEAT TRANSFER IN THE PERFORATED FINS ISSN-L: 2223-9553, ISSN: 2223-9944 Vol. 4 No. 3 Ma 2013 Aademi Researh International EFFECT THE FORM OF PERFORATION ON THE HEAT TRANSFER IN THE PERFORATED FINS Raaid R. Jassem Department o Mehanial Engineering,

More information

Department of Mechanical Engineering

Department of Mechanical Engineering Department o Mehanial Engineering AMEE41 / ATO4 Aerodynamis Instrutor: Marios M. Fyrillas Email: eng.m@it.a.y Homework Assignment #4 QESTION 1 Consider the boundary layer low on a lat plate o width b (shown

More information

MHD Homogeneous-Heterogeneous Reactions in a Nanofluid due to a Permeable Shrinking Surface

MHD Homogeneous-Heterogeneous Reactions in a Nanofluid due to a Permeable Shrinking Surface Journal o Applied Fluid Mehanis, Vol. 9, No. 3, pp. 73-79, 6. Available online at www.jamonline.net, ISSN 735-357, EISSN 735-3645. DOI:.8869/aadpub.jam.68.8.344 MHD Homogeneous-Heterogeneous Reations in

More information

Acoustic Attenuation Performance of Helicoidal Resonator Due to Distance Change from Different Cross-sectional Elements of Cylindrical Ducts

Acoustic Attenuation Performance of Helicoidal Resonator Due to Distance Change from Different Cross-sectional Elements of Cylindrical Ducts Exerpt rom the Proeedings o the COMSOL Conerene 1 Paris Aousti Attenuation Perormane o Helioidal Resonator Due to Distane Change rom Dierent Cross-setional Elements o Cylindrial Duts Wojieh ŁAPKA* Division

More information

An Experimental Study of Heat Transfer Enhancement in the Perforated Rectangular Fin

An Experimental Study of Heat Transfer Enhancement in the Perforated Rectangular Fin J Integr Si Tenol, 016, 4(1, 5-9. Artile. Journal o Integrated SCIENCE & TECHNOLOGY An Eperimental Stud o Heat Transer Enanement in te Perorated Retangular Fin Lalta Prasad, * Sonika Tewari, Aswani Kumar

More information

Review for Exam #2. Specific Heat, Thermal Conductivity, and Thermal Diffusivity. Conduction

Review for Exam #2. Specific Heat, Thermal Conductivity, and Thermal Diffusivity. Conduction Review for Exam # Speifi Heat, Thermal Condutivity, and Thermal Diffusivity Speifi heat ( p ) A measure of how muh energy is required to raise the temperature of an objet Thermal ondutivity (k) A measure

More information

A novel Infrared Thermography (IRT) based experimental technique for distributed temperature measurements in hot gas flows

A novel Infrared Thermography (IRT) based experimental technique for distributed temperature measurements in hot gas flows QIRT 1 1 http://dx.doi.org/1.1611/qirt.1.45 th International Conerene on Quantitative InraRed Thermography July 7-3, 1, Québe (Canada A novel Inrared Thermography (IRT based experimental tehnique or distributed

More information

Homework Set 4. gas B open end

Homework Set 4. gas B open end Homework Set 4 (1). A steady-state Arnold ell is used to determine the diffusivity of toluene (speies A) in air (speies B) at 298 K and 1 atm. If the diffusivity is DAB = 0.0844 m 2 /s = 8.44 x 10-6 m

More information

EFFECTS OF AIRFLOW PARAMETERS ON AIRCRAFT ICING CHARACTERISTICS

EFFECTS OF AIRFLOW PARAMETERS ON AIRCRAFT ICING CHARACTERISTICS Proeedins o the Asian Conerene on Thermal Sienes 7, st ACTS Marh -, 7, Jeju Island, Korea EFFECTS OF AIRFLOW PARAMETERS ON AIRCRAFT ICING CHARACTERISTICS Xuan Zhan, Jinhun Min *, Xiaomin Wu Tsinhua University,

More information

f 2 f n where m is the total mass of the object. Expression (6a) is plotted in Figure 8 for several values of damping ( ).

f 2 f n where m is the total mass of the object. Expression (6a) is plotted in Figure 8 for several values of damping ( ). F o F o / k A = = 6 k 1 + 1 + n r n n n RESONANCE It is seen in Figure 7 that displaement and stress levels tend to build up greatly when the oring requeny oinides with the natural requeny, the buildup

More information

MICROSCALE SIMULATIONS OF CONDUCTIVE / RADIATIVE HEAT TRANSFERS IN POROUS MEDIA

MICROSCALE SIMULATIONS OF CONDUCTIVE / RADIATIVE HEAT TRANSFERS IN POROUS MEDIA MICROCALE IMULAION OF CONDUCIVE / RADIAIVE HEA RANFER IN POROU MEDIA J.-F. hovert, V.V. Mourzenko, C. Roudani Institut PPRIME-CNR Context, motivation moldering in porous media 400K (measured) Mirosale

More information

Heat exchangers: Heat exchanger types:

Heat exchangers: Heat exchanger types: Heat exhangers: he proess of heat exhange between two fluids that are at different temperatures and separated by a solid wall ours in many engineering appliations. he devie used to implement this exhange

More information

Homework Assignment Number Two. where, for the oxygen molecule κ = ,

Homework Assignment Number Two. where, for the oxygen molecule κ = , D. eer, MSE 506, Dept. o Materials Siene & Engineering, University o Tennessee, noville Homework Assignment Numer Two Prolem. Consider the Peng-Roinson Equation o state as given elow. The ritial temperature

More information

Example Calculations of Uncertainty

Example Calculations of Uncertainty nertainty Examples. Example alulations of nertainty Instrument Bias nertainty Example # A D voltage of -.65 volts is measured with an Agilent #05A Multimeter. Aording to the data sheet (p.5.) the D auray

More information

ARMA INTRODUCTION

ARMA INTRODUCTION ARMA 1-5 Coulomb stress hange during and ater tensile rature opening in a geothermal reservoir Urpi, L. GFZ German Researh Centre For Geosienes, Potsdam, Germany Blöher, G. and Zimmermann, G.. GFZ German

More information

Answers to test yourself questions

Answers to test yourself questions Answers to test yoursel questions Topi.1 Osilliations 1 a A n osillation is any motion in whih the displaement o a partile rom a ixed point keeps hanging diretion and there is a periodiity in the motion

More information

Chapter 2: One-dimensional Steady State Conduction

Chapter 2: One-dimensional Steady State Conduction 1 Chapter : One-imensional Steay State Conution.1 Eamples of One-imensional Conution Eample.1: Plate with Energy Generation an Variable Conutivity Sine k is variable it must remain insie the ifferentiation

More information

Microeconomic Theory I Assignment #7 - Answer key

Microeconomic Theory I Assignment #7 - Answer key Miroeonomi Theory I Assignment #7 - Answer key. [Menu priing in monopoly] Consider the example on seond-degree prie disrimination (see slides 9-93). To failitate your alulations, assume H = 5, L =, and

More information

DRAFT ANALYSIS OF PUMPING REQUIREMENTS FOR MICROCHANNEL COOLING SYSTEMS. Vishal Singhal, Dong Liu and Suresh V. Garimella

DRAFT ANALYSIS OF PUMPING REQUIREMENTS FOR MICROCHANNEL COOLING SYSTEMS. Vishal Singhal, Dong Liu and Suresh V. Garimella Proeedings of IPACK03 International Eletroni Pakaging Tehnial Conferene and Exhibition July 6 11, 003, Maui, Haaii, USA DRAFT InterPak003-3537 ANALYSIS OF PUMPING REQUIREMENTS FOR MICROCHANNEL COOLING

More information

For a classical composite material, the modulus change should follow the rule of mixtures:

For a classical composite material, the modulus change should follow the rule of mixtures: Eletroni Supplementary Material (ESI for Journal of Materials Chemistry C. This journal is The Royal Soiety of Chemistry 2017 Eletroni Supplementary Information (ESI Super ompatible funtional BN nanosheets/polymer

More information

Field and Wave Electromagnetic

Field and Wave Electromagnetic Field and Wave Eletromagneti Chapter Waveguides and Cavit Resonators Introdution () * Waveguide - TEM waves are not the onl mode o guided waves - The three tpes o transmission lines (parallel-plate, two-wire,

More information

Improving the worthiness of the Elder problem as a benchmark for buoyancy driven convection models

Improving the worthiness of the Elder problem as a benchmark for buoyancy driven convection models Improving the worthiness of the Elder problem as a benhmark for buoyany driven onvetion models Maarten van Reeuwijk, Simon A. Mathias The Department of Civil and Environmental Engineering Imperial College

More information

2. The Energy Principle in Open Channel Flows

2. The Energy Principle in Open Channel Flows . The Energy Priniple in Open Channel Flows. Basi Energy Equation In the one-dimensional analysis of steady open-hannel flow, the energy equation in the form of Bernoulli equation is used. Aording to this

More information

2015 American Journal of Engineering Research (AJER)

2015 American Journal of Engineering Research (AJER) American Journal o Engineering Research (AJER) 2015 American Journal o Engineering Research (AJER) e-issn: 2320-0847 p-issn : 2320-0936 Volume-4, Issue-7, pp-33-40.ajer.org Research Paper Open Access The

More information

Supplementary Information. Infrared Transparent Visible Opaque Fabrics (ITVOF) for Personal Cooling

Supplementary Information. Infrared Transparent Visible Opaque Fabrics (ITVOF) for Personal Cooling Supplementary Information Infrared Transparent Visible Opaque Fabris (ITVOF) for Personal Cooling Jonathan K. Tong 1,Ɨ, Xiaopeng Huang 1,Ɨ, Svetlana V. Boriskina 1, James Loomis 1, Yanfei Xu 1, and Gang

More information

THERMODYNAMICS Lecture 15: Heat exchangers

THERMODYNAMICS Lecture 15: Heat exchangers HERMODYNAMICS Leture 5: Heat exangers Pierwsza strona Introdution to Heat Exangers Wat Are Heat Exangers? Heat exangers are units designed to transfer eat from a ot flowing stream to a old flowing stream

More information

An Analytical Formulation of Stress-Block Parameters for Confined Concrete

An Analytical Formulation of Stress-Block Parameters for Confined Concrete The Open Constrution and Building Tehnology Journal, 8,, 37-8 37 Open Aess An Analytial Formulation o Stress-Blok Parameters or Conined Conrete Frano Braga, Rosario Gigliotti, Mihelangelo Laterza* and

More information

ANALYTICAL MODELING ON DEBONDING FAILURE OF FRP-STRENGTHENED RC FLEXURAL STRUCTURES. Abstract. Introduction

ANALYTICAL MODELING ON DEBONDING FAILURE OF FRP-STRENGTHENED RC FLEXURAL STRUCTURES. Abstract. Introduction ANALYTICAL MODELING ON DEBONDING FAILURE OF FR-STRENGTHENED RC FLEXURAL STRUCTURES Dr. Hedong Niu, Ibaraki University, Hitahi, Japan ro. Zhishen Wu, Ibaraki University, Hitahi, Japan Abstrat Eetive appliation

More information

Chemical Reaction and Particle Size Effects on Convective Heat and Mass Transfer Through a Nano Fluid

Chemical Reaction and Particle Size Effects on Convective Heat and Mass Transfer Through a Nano Fluid ISSN (Online): 319-764 Imat Fator (1): 3.358 Chemial Reation an Partile Size Eets on Convetive eat an Mass Transer Through a Nano Flui G. V. P. N. Srikanth 1, G. Srinivas 1 Deartment o Mathematis, Guru

More information

BOUNDARY LAYER ANALYSIS ALONG A STRETCHING WEDGE SURFACE WITH MAGNETIC FIELD IN A NANOFLUID

BOUNDARY LAYER ANALYSIS ALONG A STRETCHING WEDGE SURFACE WITH MAGNETIC FIELD IN A NANOFLUID Proceedings o the International Conerence on Mechanical Engineering and Reneable Energy 7 (ICMERE7) 8 December, 7, Chittagong, Bangladesh ICMERE7-PI- BOUNDARY LAYER ANALYSIS ALONG A STRETCHING WEDGE SURFACE

More information

Pin Fin Lab Report Example. Names. ME331 Lab

Pin Fin Lab Report Example. Names. ME331 Lab Pin Fin Lab Report Example Names ME331 Lab 04/12/2017 1. Abstract The purposes of this experiment are to determine pin fin effectiveness and convective heat transfer coefficients for free and forced convection

More information

Ph1c Analytic Quiz 2 Solution

Ph1c Analytic Quiz 2 Solution Ph1 Analyti Quiz 2 olution Chefung Chan, pring 2007 Problem 1 (6 points total) A small loop of width w and height h falls with veloity v, under the influene of gravity, into a uniform magneti field B between

More information

Effect of Droplet Distortion on the Drag Coefficient in Accelerated Flows

Effect of Droplet Distortion on the Drag Coefficient in Accelerated Flows ILASS Amerias, 19 th Annual Conerene on Liquid Atomization and Spray Systems, Toronto, Canada, May 2006 Eet o Droplet Distortion on the Drag Coeiient in Aelerated Flows Shaoping Quan, S. Gopalakrishnan

More information

ACE Engineering Academy. Hyderabad Delhi Bhopal Pune Bhubaneswar Lucknow Patna Bengaluru Chennai Vijayawada Vizag Tirupati Kukatpally Kolkata

ACE Engineering Academy. Hyderabad Delhi Bhopal Pune Bhubaneswar Lucknow Patna Bengaluru Chennai Vijayawada Vizag Tirupati Kukatpally Kolkata Hyderabad eli opal une ubaneswar uknow atna engaluru Cennai ijayawada izag Tirupati Kukatpally Kolkata : : Meanial Engg. _ ESE MAINS 0(a). Sol: 0(b). Sol: p F C.G. A F ga 9.8000 9 5 0.8 kn I M C G sin

More information

NON-LINEAR BENDING CHARACTERISTICS OF PHC PILES UNDER VARYING AXIAL LOAD

NON-LINEAR BENDING CHARACTERISTICS OF PHC PILES UNDER VARYING AXIAL LOAD 13 th World Conferene on Earthquake Engineering Vanouver, B.C., Canada August 1-6, 24 aper No. 356 NON-LINEAR BENDING CHARACTERISTICS OF HC ILES UNDER VARYING AXIAL LOAD Toshihiko ASO 1 Fusanori MIURA

More information

Acoustic Waves in a Duct

Acoustic Waves in a Duct Aousti Waves in a Dut 1 One-Dimensional Waves The one-dimensional wave approximation is valid when the wavelength λ is muh larger than the diameter of the dut D, λ D. The aousti pressure disturbane p is

More information

10.2 The Occurrence of Critical Flow; Controls

10.2 The Occurrence of Critical Flow; Controls 10. The Ourrene of Critial Flow; Controls In addition to the type of problem in whih both q and E are initially presribed; there is a problem whih is of pratial interest: Given a value of q, what fators

More information

ENGINEERING OF NUCLEAR REACTORS. Tuesday, October 9 th, 2014, 1:00 2:30 p.m.

ENGINEERING OF NUCLEAR REACTORS. Tuesday, October 9 th, 2014, 1:00 2:30 p.m. .31 ENGINEERING OF NUCLEAR REACTORS Tuesday, October 9 th, 014, 1:00 :30 p.m. OEN BOOK QUIZ 1 (solutions) roblem 1 (50%) Loss o condensate pump transient in a LWR condenser i) Consider the seaater in the

More information

Beams on Elastic Foundation

Beams on Elastic Foundation Professor Terje Haukaas University of British Columbia, Vanouver www.inrisk.ub.a Beams on Elasti Foundation Beams on elasti foundation, suh as that in Figure 1, appear in building foundations, floating

More information

Emergence of Superpeer Networks: A New Perspective

Emergence of Superpeer Networks: A New Perspective Emergene o Suereer Networs: A New Persetive Bivas Mitra Deartment o Comuter Siene & Engineering Indian Institute o Tehnology, Kharagur, India Peer to Peer arhiteture Node Node Node Internet Node Node All

More information

CONTROL OF THERMAL CRACKING USING HEAT OF CEMENT HYDRATION IN MASSIVE CONCRETE STRUCTURES

CONTROL OF THERMAL CRACKING USING HEAT OF CEMENT HYDRATION IN MASSIVE CONCRETE STRUCTURES CONROL OF HERMAL CRACKING USING HEA OF CEMEN HYDRAION IN MASSIVE CONCREE SRUCURES. Mizobuhi (1), G. Sakai (),. Ohno () and S. Matsumoto () (1) Department of Civil and Environmental Engineering, HOSEI University,

More information

Buckling loads of columns of regular polygon cross-section with constant volume and clamped ends

Buckling loads of columns of regular polygon cross-section with constant volume and clamped ends 76 Bukling loads of olumns of regular polygon ross-setion with onstant volume and lamped ends Byoung Koo Lee Dept. of Civil Engineering, Wonkwang University, Iksan, Junuk, 7-79, Korea Email: kleest@wonkwang.a.kr

More information

Mass Transfer (Stoffaustausch) Fall 2012

Mass Transfer (Stoffaustausch) Fall 2012 Mass Transfer (Stoffaustaush) Fall Examination 9. Januar Name: Legi-Nr.: Edition Diffusion by E. L. Cussler: none nd rd Test Duration: minutes The following materials are not permitted at your table and

More information

Thermal Power Density Barriers of Converter Systems

Thermal Power Density Barriers of Converter Systems Thermal Power Density Barriers of Converter Systems Uwe DOFENIK and Johann W. KOLA Power Eletroni Systems Laboratory (PES ETH Zurih ETH-Zentrum / ETL H CH-89 Zurih Switzerland Phone: +4--6-467 Fax: +4--6-

More information

Beam Stresses Bending and Shear

Beam Stresses Bending and Shear Beam Stresses Bending and Shear Notation: A = name or area A web = area o the web o a wide lange setion b = width o a retangle = total width o material at a horizontal setion = largest distane rom the

More information

MTH 142 Solution Practice for Exam 2

MTH 142 Solution Practice for Exam 2 MTH 4 Solution Pratie for Eam Updated /7/4, 8: a.m.. (a) = 4/, hene MID() = ( + + ) +/ +6/ +/ ( 4 ) =. ( LEFT = ( 4..). =.7 and RIGHT = (.. ). =.7. Hene TRAP =.7.. (a) MID = (.49 +.48 +.9 +.98). = 4.96.

More information

(SO/EC - 70-005 Certified) Model nswer: Summer 7 Code: 17 mportant nstrutions to examiners: 1) The answers should e examined y key words and not as word-to-word as given in the model answer sheme. ) The

More information

EFFECT OF PITCH NUMBER IN OVERALL HEAT TRANSFER RATE IN DOUBLE PIPE HELICAL HEAT EXCHANGER

EFFECT OF PITCH NUMBER IN OVERALL HEAT TRANSFER RATE IN DOUBLE PIPE HELICAL HEAT EXCHANGER Volume 116 No. 5 2017, 1-6 ISSN: 1311-8080 (printed version); ISSN: 1314-3395 (on-line version) url: http://www.ijpam.eu ijpam.eu EFFECT OF PITCH NUMBER IN OVERALL HEAT TRANSFER RATE IN DOUBLE PIPE HELICAL

More information

Q c, Q f denote the outputs of good C and F, respectively. The resource constraints are: T since the technology implies: Tc = Qc

Q c, Q f denote the outputs of good C and F, respectively. The resource constraints are: T since the technology implies: Tc = Qc Fall 2008 Eon 455 Ansers - Problem Set 3 Harvey Lapan 1. Consider a simpliied version o the Heksher-Ohlin model ith the olloing tehnology: To produe loth: three units o labor and one unit o land are required

More information

Software Verification

Software Verification Sotare Veriiation EXAMPLE NZS 3101-06 RC-BM-001 Flexural and Shear Beam Deign PROBLEM DESCRIPTION The purpoe o thi example i to veriy lab lexural deign in. The load level i adjuted or the ae orreponding

More information

4.4 Solving Systems of Equations by Matrices

4.4 Solving Systems of Equations by Matrices Setion 4.4 Solving Systems of Equations by Matries 1. A first number is 8 less than a seond number. Twie the first number is 11 more than the seond number. Find the numbers.. The sum of the measures of

More information

PHYSICS 212 FINAL EXAM 21 March 2003

PHYSICS 212 FINAL EXAM 21 March 2003 PHYSIS INAL EXAM Marh 00 Eam is losed book, losed notes. Use only the provided formula sheet. Write all work and answers in eam booklets. The baks of pages will not be graded unless you so ruest on the

More information

EXPERIMENTAL AND NUMERICAL STUDY OF EVAPORATING FLOW HEAT TRANSFER IN MICRO-CHANNEL HOKI LEE

EXPERIMENTAL AND NUMERICAL STUDY OF EVAPORATING FLOW HEAT TRANSFER IN MICRO-CHANNEL HOKI LEE EXPERIMENTAL AND NUMERICAL STUDY OF EVAPORATING FLOW HEAT TRANSFER IN MICRO-CHANNEL By HOKI LEE A thesis submitted in partial fulfillment of the requirements for the degree of DOCTOR OF PHILOSOPHY WASHINGTON

More information

Integrated dynamics modeling for supercavitating vehicle systems

Integrated dynamics modeling for supercavitating vehicle systems SNAK, 015 Int. J. Nav. Arhit. Oean ng. (015) 7:346~363 http://dx.doi.org/10.1515/ijnaoe-015-004 pissn: 09-678, eissn: 09-6790 Integrated dynamis modeling or superavitating vehile systems Seonhong Kim and

More information

Confinement of Reinforced Concrete Columns

Confinement of Reinforced Concrete Columns This artile was downloaded by: 10.3.98.93 On: 22 Nov 2018 Aess details: subsription number Publisher: CRC Press Inorma Ltd Registered in England and Wales Registered Number: 1072954 Registered oie: 5 Howik

More information

PREDICTION OF CONCRETE COMPRESSIVE STRENGTH

PREDICTION OF CONCRETE COMPRESSIVE STRENGTH PREDICTION OF CONCRETE COMPRESSIVE STRENGTH Dunja Mikuli (1), Ivan Gabrijel (1) and Bojan Milovanovi (1) (1) Faulty o Civil Engineering, University o Zagreb, Croatia Abstrat A ompressive strength o onrete

More information

Motor Sizing Application Note

Motor Sizing Application Note PAE-TILOGY Linear Motors 70 Mill orest d. Webster, TX 77598 (8) 6-7750 ax (8) 6-7760 www.trilogysystems.om E-mail emn_support_trilogy@parker.om Motor Sizing Appliation Note By Jak Marsh Introdution Linear

More information

Strauss PDEs 2e: Section Exercise 3 Page 1 of 13. u tt c 2 u xx = cos x. ( 2 t c 2 2 x)u = cos x. v = ( t c x )u

Strauss PDEs 2e: Section Exercise 3 Page 1 of 13. u tt c 2 u xx = cos x. ( 2 t c 2 2 x)u = cos x. v = ( t c x )u Strauss PDEs e: Setion 3.4 - Exerise 3 Page 1 of 13 Exerise 3 Solve u tt = u xx + os x, u(x, ) = sin x, u t (x, ) = 1 + x. Solution Solution by Operator Fatorization Bring u xx to the other side. Write

More information

CEN/TC 250/SC 3 N 2634

CEN/TC 250/SC 3 N 2634 CEN/TC 50/SC N 64 CEN/TC 50/SC Euroode - Design o steel strutures E-mail o Seretar: susan.kempa@din.de Seretariat: DIN EN 99--5 First Drat Date o doument 08-05-0 Expeted ation Comment Due Date 08-06-9

More information

Blackbody radiation and Plank s law

Blackbody radiation and Plank s law lakbody radiation and Plank s law blakbody problem: alulating the intensity o radiation at a given wavelength emitted by a body at a speii temperature Max Plank, 900 quantization o energy o radiation-emitting

More information

TORSION By Prof. Ahmed Amer

TORSION By Prof. Ahmed Amer ORSION By Prof. Ahmed Amer orque wisting moments or torques are fores ating through distane so as to promote rotation. Example Using a wrenh to tighten a nut in a bolt. If the bolt, wrenh and fore are

More information

Mechanical waves, acoustics and ultrasounds

Mechanical waves, acoustics and ultrasounds Mehanial waves, aoustis and ultrasounds Leture or reshmen medial students Péter Maróti Preparation or the exam Leture (slide show, see the home page o the Institute) Handout (more text, see the home page

More information

Problem 3.73 Known: Composite wall with outer surfaces exposed to convection process while the inner wall experiences uniform heat generation

Problem 3.73 Known: Composite wall with outer surfaces exposed to convection process while the inner wall experiences uniform heat generation Problem 3.73 Known: omposite wall with outer surfaces eposed to ection process while the inner wall eperiences uniform heat generation Unnown: Volumetric heat generation and thermal conductivity for material

More information

2. Mass transfer takes place in the two contacting phases as in extraction and absorption.

2. Mass transfer takes place in the two contacting phases as in extraction and absorption. PRT 11- CONVECTIVE MSS TRNSFER 2.1 Introdution 2.2 Convetive Mass Transfer oeffiient 2.3 Signifiant parameters in onvetive mass transfer 2.4 The appliation of dimensional analysis to Mass Transfer 2.4.1

More information

Reliability Estimation of Solder Joints Under Thermal Fatigue with Varying Parameters by using FORM and MCS

Reliability Estimation of Solder Joints Under Thermal Fatigue with Varying Parameters by using FORM and MCS Proeedings o the World Congress on Engineering 2007 Vol II Reliability Estimation o Solder Joints Under Thermal Fatigue with Varying Parameters by using FORM and MCS Ouk Sub Lee, Yeon Chang Park, and Dong

More information

Numerical Simulation of Fluid Flow and Heat transfer in a Rotary Regenerator

Numerical Simulation of Fluid Flow and Heat transfer in a Rotary Regenerator Numerical Simulation o Fluid Flo and Heat transer in a Rotary Regenerator M. Mousavi 1, M. Passandideh-Fard and M. Ghazikhani 3 1 Graduate Student,, 3 Assistant Proessors Department o Mechanical Engineering,

More information

Numerical Analysis of Electroconvection Phenomena in Cross-flow

Numerical Analysis of Electroconvection Phenomena in Cross-flow Numerial Analysis o Eletroonvetion Phenomena in Cross-low Yiei Guan and Igor Novosselov Department o Mehanial Engineering, University o Washington, Seattle, U.S.A. 98195 Deember 018 Eletroonvetive phenomena

More information

A Study of Dufour and Soret Effect on MHD Mixed Convection Stagnation Point Flow towards a Vertical Plate in a Porous Medium

A Study of Dufour and Soret Effect on MHD Mixed Convection Stagnation Point Flow towards a Vertical Plate in a Porous Medium International Journal of Fluids Engineering. ISSN 0974-3138 Volume 9, Number 1 (017), pp. 1-8 International Researh Publiation House http://www.irphouse.om A Study of Dufour and Soret Effet on MHD Mixed

More information

1. Which two values of temperature are equivalent to the nearest degree when measured on the Kelvin and on the

1. Which two values of temperature are equivalent to the nearest degree when measured on the Kelvin and on the . Whih two values of teperature are equivalent to the nearest degree when easured on the Kelvin and on the Celsius sales of teperature? Kelvin sale Celsius sale A. 40 33 B. 273 00 C. 33 40 D. 373 0 2.

More information

Study of Thermally Induced Vibration of Non-Homogeneous Trapezoidal Plate with Varying Thickness and Density

Study of Thermally Induced Vibration of Non-Homogeneous Trapezoidal Plate with Varying Thickness and Density Amerian Journal of Computational and Applied Mathematis, (6: 65-75 DOI:.59/j.ajam.6.5 Study of Thermally Indued Viration of Non-Homogeneous Trapezoidal Plate ith Varying Thikness and Density Arun Kumar

More information

Determination of the rotational restraint coefficient and local buckling of orthotropic box columns

Determination of the rotational restraint coefficient and local buckling of orthotropic box columns etermination of the rotational restraint oeffiient and loal ukling of orthotropi o olumns A. A. Maghsoudi, H. Saffari & H. Rezaeian epartment of Civil Engineering, Shahid Bahonar University, Iran Astrat

More information

Evaluation of an integrated photovoltaic thermal solar (IPVTS) water heating system for various configurations at constant collection temperature

Evaluation of an integrated photovoltaic thermal solar (IPVTS) water heating system for various configurations at constant collection temperature Evaluation o an integrated photovoltai thermal solar (IPVTS) water heating system or various onigurations at onstant olletion temperature Rajeev Kumar Mishra 1,*, G.N.Tiwari 1 1 Centre or Energy Studies,

More information

Numerical modeling of the thermoelectric cooler with a complementary equation for heat circulation in air gaps

Numerical modeling of the thermoelectric cooler with a complementary equation for heat circulation in air gaps Open Phys. 17; 15:7 34 Researh Artile Open Aess En Fang*, Xiaojie Wu, Yuesen Yu, and Junrui Xiu Numerial modeling of the thermoeletri ooler with a omplementary equation for heat irulation in air gaps DOI

More information

Principles of Food and Bioprocess Engineering (FS 231) Solutions to Example Problems on Freezing

Principles of Food and Bioprocess Engineering (FS 231) Solutions to Example Problems on Freezing Principles o Food and Bioprocess Engineering (FS 21) Solutions to Example Problems on Freezing 1. In order to determine the a to be used in the above equation, e recall that Plank s equation is valid or

More information

DIGITAL DISTANCE RELAYING SCHEME FOR PARALLEL TRANSMISSION LINES DURING INTER-CIRCUIT FAULTS

DIGITAL DISTANCE RELAYING SCHEME FOR PARALLEL TRANSMISSION LINES DURING INTER-CIRCUIT FAULTS CHAPTER 4 DIGITAL DISTANCE RELAYING SCHEME FOR PARALLEL TRANSMISSION LINES DURING INTER-CIRCUIT FAULTS 4.1 INTRODUCTION Around the world, environmental and ost onsiousness are foring utilities to install

More information

INFORMATION CONCERNING MATERIALS TO BE USED IN THE DESIGN

INFORMATION CONCERNING MATERIALS TO BE USED IN THE DESIGN TITLE 5 DESIGN CHAPTER 8 INFORMATION CONCERNING MATERIALS TO BE USED IN THE DESIGN Artile 38. Charateristis o steel or reinorements 38.1 General The harateristis o the steel used or the design desribed

More information

Stress triaxiality to evaluate the effective distance in the volumetric approach in fracture mechanics

Stress triaxiality to evaluate the effective distance in the volumetric approach in fracture mechanics IOSR Journal of ehanial and Civil Engineering (IOSR-JCE) e-issn: 78-1684,p-ISSN: 30-334X, Volume 11, Issue 6 Ver. IV (Nov- De. 014), PP 1-6 Stress triaxiality to evaluate the effetive distane in the volumetri

More information

CONVECTION AT A.MODEL ICE EDGE

CONVECTION AT A.MODEL ICE EDGE JACK CALMAN CONVECTION AT A.MODEL ICE EDGE The flow pattern near the edge of a melting ie blok is modeled by heating a metal edge in a saltstratified fluid. An unexpetedly strong, horizontal boundary urrent

More information

COMBINED EFFECTS OF RADIATION AND HEAT GENERATION ON MHD NATURAL CONVECTION FLOW ALONG A VERTICAL FLAT PLATE IN PRESENCE OF HEAT CONDUCTION

COMBINED EFFECTS OF RADIATION AND HEAT GENERATION ON MHD NATURAL CONVECTION FLOW ALONG A VERTICAL FLAT PLATE IN PRESENCE OF HEAT CONDUCTION BRAC University Journal, vol.vi, no., 9, pp 11- COMBINED EFFECTS OF RADIATION AND HEAT GENERATION ON MHD NATURAL CONVECTION FLOW ALONG A VERTICAL FLAT PLATE IN PRESENCE OF HEAT CONDUCTION Mohammad Mokaddes

More information

Topics Adiabatic Combustion Adiabatic Flame Temperature Example Combustion Efficiency Second and First Law Efficiencies Contrasted Example Problem

Topics Adiabatic Combustion Adiabatic Flame Temperature Example Combustion Efficiency Second and First Law Efficiencies Contrasted Example Problem ME 410 Day 12 opis diabati Combustion diabati Flame emperature Example Combustion Eiieny Seond and First Law Eiienies Contrasted Example roblem 1. he Case o diabati Combustion Here is it assumed that there

More information

Notation 2, 8, 1 2, 8, 2 2, 8

Notation 2, 8, 1 2, 8, 2 2, 8 Page 90 Atomi struture 2 1 a Contains 3 protons (1); and 4 neutrons (1) Page 90 Eletroni struture 2 a 2, 8 Type of reation Ionisation Nulear fission Nulear fusion Change in mass of nuleus Stays the same

More information

Appendix A Market-Power Model of Business Groups. Robert C. Feenstra Deng-Shing Huang Gary G. Hamilton Revised, November 2001

Appendix A Market-Power Model of Business Groups. Robert C. Feenstra Deng-Shing Huang Gary G. Hamilton Revised, November 2001 Appendix A Market-Power Model of Business Groups Roert C. Feenstra Deng-Shing Huang Gary G. Hamilton Revised, Novemer 200 Journal of Eonomi Behavior and Organization, 5, 2003, 459-485. To solve for the

More information

UNIVERSAL RELATIONSHIP BETWEEN COLLECTION EFFICIENCY AND THE CORONA POWER OF THE ELECTROSTATIC PRECIPITATOR

UNIVERSAL RELATIONSHIP BETWEEN COLLECTION EFFICIENCY AND THE CORONA POWER OF THE ELECTROSTATIC PRECIPITATOR Australia 006 Paper 5B UNIVERSAL RELATIONSHIP BETWEEN COLLECTION EFFICIENCY AND THE CORONA POWER OF THE ELECTROSTATIC PRECIPITATOR YAKOV S. KHODORKOVSKY & MICHAEL R. BELTRAN Beltran, In., U.S.A. ABSTRACT

More information

PROBLEM 3.8 ( ) 20 C 10 C m m m W m K W m K 1.4 W m K. 10 W m K 80 W m K

PROBLEM 3.8 ( ) 20 C 10 C m m m W m K W m K 1.4 W m K. 10 W m K 80 W m K PROBLEM 3.8 KNOWN: Dimensions of a thermopane window. Room and ambient air conditions. FIND: (a) Heat loss through window, (b) Effect of variation in outside convection coefficient for double and triple

More information

EFFECTS OF CHEMICAL REACTION ON MHD BOUNDARY LAYER FLOW OVER AN EXPONENTIALLY STRETCHING SHEET WITH JOULE HEATING AND THERMAL RADIATION

EFFECTS OF CHEMICAL REACTION ON MHD BOUNDARY LAYER FLOW OVER AN EXPONENTIALLY STRETCHING SHEET WITH JOULE HEATING AND THERMAL RADIATION International Research Journal o Engineering and Technology (IRJET) e-issn: 395-56 Volume: Issue: 9 Dec-5.irjet.net p-issn: 395-7 EFFECTS OF CHEMICAL REACTION ON MHD BOUNDARY LAYER FLOW OVER AN EXPONENTIALLY

More information

Controlling the Heat Flux Distribution by Changing the Thickness of Heated Wall

Controlling the Heat Flux Distribution by Changing the Thickness of Heated Wall J. Basic. Appl. Sci. Res., 2(7)7270-7275, 2012 2012, TextRoad Publication ISSN 2090-4304 Journal o Basic and Applied Scientiic Research www.textroad.com Controlling the Heat Flux Distribution by Changing

More information

The effects of suction and injection on a moving flat plate in a parallel stream with prescribed surface heat flux

The effects of suction and injection on a moving flat plate in a parallel stream with prescribed surface heat flux Noriah Bachok Anuar Ishak The eects o suction inection on a moving lat plate in a parallel stream ith prescribed surace heat lux NORFIFAH BACHOK & ANUAR ISHAK Department o Mathematics Faculty o Science

More information

Chapter 3 Lecture 7. Drag polar 2. Topics. Chapter-3

Chapter 3 Lecture 7. Drag polar 2. Topics. Chapter-3 hapter 3 eture 7 Drag polar Topis 3..3 Summary of lift oeffiient, drag oeffiient, pithing moment oeffiient, entre of pressure and aerodynami entre of an airfoil 3..4 Examples of pressure oeffiient distributions

More information

Minimum flexural reinforcement in rectangular and T-section concrete beams

Minimum flexural reinforcement in rectangular and T-section concrete beams Tehnial Paper lberto Carpinteri Eria Cadamuro Mauro Corrado* DOI: 10.1002/suo.201300056 Minimum lexural reinorement in retangular and T-setion onrete beams The presriptions provided by odes o pratie or

More information

Characterisation of Balcony Spill Plume Entrainment using Physical Scale Modelling

Characterisation of Balcony Spill Plume Entrainment using Physical Scale Modelling Charaterisation of Balony Spill Plume Entrainment using Physial Sale Modelling ROGER HARRISON and MICHAEL SPEARPOINT Department of Civil and Natural Resoures Engineering University of Canterury Christhurh,

More information

SEDIMENT TRANSPORT CALCULATION CONSIDERING COHESIVE EFFECTS AND ITS APPLICATION TO WAVE-INDUCED TOPOGRAPHIC CHANGE

SEDIMENT TRANSPORT CALCULATION CONSIDERING COHESIVE EFFECTS AND ITS APPLICATION TO WAVE-INDUCED TOPOGRAPHIC CHANGE Proeedings of the 7 th International Conferene on Asian and Paifi Coasts (APAC 03) Bali, Indonesia, September 4-6, 03 SEDIMENT TRANSPORT CALCULATION CONSIDERING COHESIVE EFFECTS AND ITS APPLICATION TO

More information

Physics (Theory) There are 30 questions in total. Question Nos. 1 to 8 are very short answer type questions and carry one mark each.

Physics (Theory) There are 30 questions in total. Question Nos. 1 to 8 are very short answer type questions and carry one mark each. Physis (Theory) Tie allowed: 3 hours] [Maxiu arks:7 General Instrutions: (i) ll uestions are opulsory. (ii) (iii) (iii) (iv) (v) There are 3 uestions in total. Question Nos. to 8 are very short answer

More information