EXAM 1. OPEN BOOK AND CLOSED NOTES.
|
|
- Conrad Byrd
- 5 years ago
- Views:
Transcription
1 ME 35 - Machine Design I Summer Semester 013 Name of Student Lab Section Number EXAM 1. OPEN BOOK AND CLOSED NOTES. Wednesday, June 6th, 013 Use the blank paper provided for your solutions. Write on one side of the paper only. Where necessary, you can use the figures provided on the exam to show vectors and instant centers. Any work that cannot be followed is assumed to be in error. At the completion of your exam, please staple each problem separately and staple your crib sheet to the end of Problem 1. Problem 1 (5 Points). Part I. (15 Points). For the mechanism shown in Figure 1a: (i) Determine the mobility using the Kutzbach criterion. Clearly number each link and label the lower pairs and the higher pairs on the given figure. (ii) Define suitable vectors for a kinematic analysis. Label and show the direction of each vector clearly on the given figure. (iii) Write the vector loop equations that are required for a kinematic analysis of the mechanism. Clearly identify suitable input(s) for the mechanism. List: (a) the known quantities; (b) the unknown variables; and (c) any constraints. If you identified constraints in part (b) then write the constraint equations. Figure 1a. A planar mechanism. Part II. (10 Points). Using trigonometry, determine the mechanical advantage of the four-bar linkage in the position shown in Fig. 1b. The input link OA = 6in, link AB = 10 in, and output link BO = in. Figure 1b. A four-bar linkage. 1
2 ME 35 - Machine Design I Summer Semester 013 Name of Student Lab Section Number Problem (5 Points). For the mechanism in the position shown in Figure, the angular velocity of the input gear is ω = 15rad / s counterclockwise. Gear 3 is rolling, without slip, on gear at the point of contact E. The radius of gear is ρ = 00 mm, the radius of gear 3 is ρ 3 = 150 mm, and the distance from point C on link 3 to pin D connecting links 3 and is CD = 500 mm. (i) Draw vectors clearly on the given figure that are suitable for a kinematic analysis of the mechanism. Then write the vector loop equation for the mechanism. (ii) Using your vector loop equation determine the first-order kinematic coefficients for the mechanism. (iii) Determine the angular velocities of links 3 and. Give the magnitudes and directions of the vectors. Figure. A planar mechanism.
3 ME 35 - Machine Design I Summer Semester 013 Name of Student Lab Section Number Problem 3 (5 Points). For the mechanism in the position shown in Figure 3, the input link is moving downward with a constant velocity V = 90mm/s. (i) List the primary instant centers and the secondary instant centers for the mechanism. (ii) Using the given Kennedy circle, show the location of all the instant centers on the given figure. Using the location of the instant centers, determine: (iii) The first-order kinematic coefficients of links 3,, and 5. (iv) The magnitudes and the directions of the angular velocities of links 3,, and 5. (v) The magnitude and direction of the velocity of point D which is fixed in link. Figure 3. A planar mechanism. Scale: full size, that is, 1 mm = 1 mm. 3
4 ME 35 - Machine Design I Summer Semester 013 Name of Student Lab Section Number Problem (5 Points). For the mechanism in the position shown in Figure, the angular velocity of the input link is ω = 50 rad / s counterclockwise. The link lengths are OA = 500mm, AB = 00 mm, and the radius of the wheel which is rolling without slipping on link 1 is ρ = 10 mm. (i) Write a vector loop equation that is suitable for a kinematic analysis of this mechanism. Draw your vectors clearly on the given figure. (ii) Using your vector loop equation determine the first-order kinematic coefficients for the mechanism. (iii) Determine the angular velocities of links 3 and. Give the magnitude and direction of each vector. (iv) Determine the velocity of point B fixed in link. Give the magnitude and direction of this vector. Figure. A planar mechanism.
5 Solution to Problem 1. Part I. (i) points. The links of the mechanism and the joints are as shown in Figure 1(a). Figure 1(a). The links and joints of the mechanism. The Kutzbach mobility criterion can be written as M = 3(n 1) j1 1j (1) The number of links, the number of lower pairs (or j 1 joints), and the number of higher pairs (or j joints), respectively, are n = 7, j1 = 8, and j = 1 () Substituting Equation () into Equation (1), the mobility of the mechanism is M = 3(7 1) (8) 1= 1 (3) This is the correct answer for this mechanism, that is, for a single input there is a unique output. (ii) Points. Suitable vectors for a kinematic analysis of the mechanism are shown in Figure 1(b). Figure 1(b). Vectors for the mechanism. 5
6 (iii) 7 Points. (a) The input link is chosen to be link (see Figure 1a) and the input variable is the angle θ. Note that link would also be suitable as an input link since it pinned to the ground link. The slider (link 7) would also be suitable as an input link. Other choices for the input link are not really practical. (b) The six unknown variables are the four angles θ 3, θ, θ 5, and θ 6 and the two distances R 36 and R 7. (c) There are four constraints, the four constraint equations are θ33 = θ3 φ (5a) θ36 = θ33 + (180 α) (5b) and θ66 = θ6 β (5c) θ333 = θ3 + γ (5d) Since there are 6 unknown variables then three independent vector loop equations are required. The three vector loop equations can be written as = o Ι?? Loop 1: R1 R R3 R (a) Loop : Loop 3: = (b)? C1? C? C3 o Ι? R R R R R R R R = (c) Ι? C1? C?? C? R R R R R R R R o Part II. 10 points. The mechanical advantage of the four-bar linkage, see Chapters 1 and 3, is defined as where the angles ψ and φ are as shown in Figure 1(c). MA R sinψ BO sinψ R sin φ AO sin φ = = (1) Figure 1(c). The four-bar linkage. 6
7 From the triangle AO B, the angles can be written as and sin sin AO AB ψ = (a) BO AB φ = (b) Sustututing Equations () into Equation (1), the mechanical advantage of the four-bar linkage can be written as AO BO BO MA = AB = (3a) BO AO BO AB Therefore, the mechanical advantage of the four-bar linkage can be written as MA BO = (3b) BO Notice that the triangle AOB is a right-angled triangle with the angle AOB = 90. Therefore, the length of OB is BO = AB O A = = () inches Substituting Equation () and the known length of the output link, that is, BO = in, into Equation (3), the mechanical advantage of the four-bar linkage is MA = = 0.5 (5) 8 7
8 Solution to Problem. (i) 7 Points. A suitable choice of vectors for the mechanism are as shown on Figure. Figure. A planar mechanism. The vector loop equation (VLE) for the mechanism can be written as C?? R R R + R = 0 (1) where link 7 is the arm. The input of this mechanism is the angular position of gear. (ii) 1 points. The rolling contact constraint between gear and link 3 can be written as ρ Δθ Δθ 3 7 ± = () ρ3 Δ θ Δ θ7 The correct sign is positive because there is internal contact between the two gears. Differentiating Equation () with respect to the input position θ gives ρ θ θ = ρ3 θ θ7 (3a) Rearranging Equation (3a) and substituting the kinematic coefficient of the input link 1 θ = into the resulting equation, the first-order kinematic coefficient for the arm (that is, link 7) can be written as 8
9 ρ3θ 3 ρ θ 7 = ρ ρ 3 (3b) Substituting the given dimensions into Equation (3b), the first-order kinematic coefficient for the arm can be written as 150θ 3 00 θ 7 = (3c) The X and Y components of the VLE, see Equation (1), are and R7cosθ7 R3cosθ3 R cosθ + R1cosθ 1= 0 (a) R7sin θ7 R3sin θ3 Rsin θ + R1sin θ 1 = 0 (b) Differentiating Equations () with respect to the input position θ gives and R sin θ θ + R sin θ θ + R sin θ θ = 0 (5a) R cos θ θ R cosθ θ R cosθ θ = 0 (5b) Then substituting Equation (3b) into Equations (5) gives and ρθ 3 3 ρ R7sin θ 7 + R3sin θ3θ 3+ Rsin θθ = 0 ρ3 ρ ρθ 3 3 ρ R7cosθ7 R3cosθ3θ 3 Rcosθθ = 0 ρ3 ρ (6a) (6b) Then writing Equations (6) in matrix form gives ρ3r7 ρ sin θ 7 + R3sin θ 3 + Rsin θ θ 3 R7sin θ7 ρ3 ρ ρ3 ρ = ρ3r7 ρ cos + θ7 R3cos θ3 Rcos θ θ + R7cos θ 7 ρ3 ρ ρ3 ρ (7) Substituting the known data into Equation (7) gives mm mm θ 3 0 mm = mm mm θ 00 mm (8a) The determinant of the coefficient matrix in Equation (8a) is DET = ( mm)( mm) ( mm)( mm) = 831 mm (8b) 9
10 Using Cramer s rule, the first-order kinematic coefficient for link 3 from Equation (8a) is mm θ 3 = = 0.90 rad / rad 831 mm (9) The negative sign indicates that link 3 is rotating clockwise as link rotates counterclockwise. Also, the first-order kinematic coefficient for link is 110 mm θ = = rad / rad 831 mm (10) The positive sign indicates that link rotates counterclockwise as gear rotates counterclockwise. Substituting Equation (9) into Equation (3c), the first-order kinematic coefficient for the arm is 150( 0.90) 00 θ 7 = = rad/rad The positive sign indicates that the arm is rotating counterclockwise as gear rotates counterclockwise. (iii) 6 Points. The angular velocity of link 3 can be written as (11) ω 3 =θ 3 ω (1a) Substituting Equation (9) and the angular velocity of the input link into Equation (1a) gives ω 3 = ( 0.90 rad )( + 15rad / s) = 7.35 rad / s (1b) The negative sign indicates that link 3 is rotating clockwise. The angular velocity of link can be written as ω =θ ω (13a) Substituting Equation (10) and the angular velocity of the input link into Equation (13a) gives ω = ( rad) ( + 15 rad / s) =+ 7.6 rad / s (1b) The positive sign indicates that link is rotating counterclockwise. Note that the angular velocity of the arm (link 7) can be written as ω 7 =θ 7 ω (15a) Substituting Equation (11) and the angular velocity of the input link into Equation (15a) gives ω 7 = ( rad )( + 15 rad / s) = rad / s (15b) The positive sign indicates that the arm (link 7) is rotating counterclockwise. 10
11 Solution to Problem 3. (i) 1 Point. The number of links in the mechanism is four, therefore, the total number of instant centers for this mechanism is six; i.e., n( n 1) 5x N = = = 10 (1) There are 6 primary instant centers; namely, I 1, I 15, I 5, I 3, I 1, and I 3. Therefore, there are secondary instant centers; namely, I, I 5, I 13, and I 35. Note: The point of intersection of the line through I 15 I 5 and the line through the contact point and perpendicular to the sliding direction is the instant center I 1. The procedure to locate the secondary instant centers is: (i) The point of intersection of the line through I 3 I 3 and the line through I 1 I 1 is the instant center I. (ii) The point of intersection of the line through I 15 I 1 and the line through I 5 I is the instant center I 5. (iii) The point of intersection of the line through I 1 I 3 and the line through I 1 I 3 is the instant center I 13. (iv) The point of intersection of the line through I 5 I 3 and the line through I 5 I 3 is the instant center I 35. (ii) 10 Points. The locations of the 10 instant centers for this mechanism are shown on Figure 3. Figure 3. The locations of the instant centers. 11
12 (iii) 6 Points. The velocity of point A fixed in link 3 is equal to the velocity of point A fixed in link, that is V = V = V (1a) which can be written as A 3 A ( I I ) ω = R Rearranging this equation, the first-order kinematic coefficient of link 3 can be written as (1b) ω 1 3 θ 3 = = R I13I3 (1c) The distance I 13 I 3 is measured as I 13 I 3 = 33.3 mm. Therefore, the first-order kinematic coefficient of link 3 is 1 θ 3 = = rad/mm (a) 33.3 mm Note that the correct sign of this kinematic coefficient is positive because link 3 is rotating counterclockwise about the instant center I 13 as the length of the input vector is increasing, that is The velocity of link can be written as θ 3 = rad/mm (b) ( I I ) ω = R 1 (3a) Rearranging this equation gives the first-order kinematic coefficient of link, that is 1 θ = (3b) I I The distance I 1 I is measured as I 1 I = 10.7 mm. Therefore, the first-order kinematic coefficient of link is 1 θ = = rad / mm (a) 10.7 mm Note that the correct sign is negative because link is rotating clockwise about the instant center I 1 while the length of the input vector is increasing, that is The velocity of link can be written as 1 θ = rad/mm (b) ( I I ) ω = R (5a) Therefore, the first-order kinematic coefficient of link 5 can be written as 1 θ 5 = (5b) I I
13 The distance I 15 I 5 is measured as I15I 5 = 16.7 mm. Therefore, the first-order kinematic coefficient is 1 θ 5 = = rad / mm (6a) 16.7 mm Note that the correct sign is negative because link 5 is rotating clockwise about the instant center I 15 while the length of the input vector is increasing, that is (iv) 6 Points. The angular velocity of link 3 can be written as θ 5 = rad/mm (6b) ω = θ R (7) 3 3 The input vector R is defined here as downward, therefore, the vector is becoming longer for the given input velocity V ˆ = 90jmm/s. Therefore, the time rate of change of the input vector is Substituting Equations (b) and (8b) into Equation (7) gives R =+ 90 mm/s (8b) ω3 = θ 3 R = ( )( + 90) =+.7 rad sec (9) The positive sign implies that the direction of the angular velocity of link 3 is counterclockwise. The angular velocity of link can be written as ω = θ R (10a) Substituting Equations (b) and (8b) into Equation (10a) gives ω = ( )( + 90) = 8.0 rad sec (10b) The negative sign implies that the direction of the angular velocity of link is clockwise. The angular velocity of link 5 can be written as ω = θ R (11a) 5 5 Substituting Equations (6b) and (8b) into Equation (11a) gives ω 5 = ( 0.06)( + 90) = 5. rad sec (11b) The negative sign implies that the direction of the angular velocity of link 5 is clockwise. (v) Points. The velocity of point D (where D is fixed in link ) can be written as V = ( I D) ω = ( I D) θ R (1a) D 1 1 The distance I 1 D is measured as I 1 D = 95 mm. Substituting this measurement and Equation (10b) into Equation (1a), the velocity of point D is V D = (95 mm)( 8.0 rad/s) = 798 mm/s (1b) The negative sign indicates that the velocity of point D is directed to the left. 13
14 Solution to Problem. (i) 8 Points. A set of vectors for a kinematic analysis of the mechanism are shown in Fig. (a). The vector loop equation (VLE) can be written as Figure (a). Suitable vectors for the mechanism. I?? R + R + R + R + R = 0 (1) where the vector R 7 is the arm and the vector R 9 follows the path of pin B. (ii) 10 Points. The X and Y components of the VLE, see Equation (1), are and Rcos θ + R3cos θ 3+ R7cos θ 7 + R9cosθ 9 + R1cos θ 1 = 0 (a) Rsin θ + R3sin θ 3+ R7sin θ 7 + R9sin θ 9 + R1sin θ 1 = 0 (b) The angles for the given position of the mechanism are θ = 10, θ 3 = 10, θ 9 = 70, and θ 7 = 180 (3) Differentiating Equations () with respect to the input position θ gives and R sin θ R sin θ θ + R cosθ = 0 (a)
15 Writing Equations () in matrix form gives + R cosθ + R cosθ θ + R sin θ = 0 (b) R3sinθ 3 + cosθ9 θ 3 + Rsinθ R3cos 3 sin 9 R = 9 Rcos + θ + θ θ (5) Substituting the known data into Equation (5) gives 00sin(10 ) mm cos(70 ) rad θ sin(10 ) mm = + 00cos(10 ) mm sin(70 ) rad R 9 500cos(10 ) mm (6a) which simplifies to + 00 mm 0 rad θ mm = 36.1 mm 1 rad R mm (6b) The determinant of the coefficient matrix in Equation (6b) is DET = ( + 00 mm)( 1 rad) = 00 mm (7a) Using Cramer s rule, the first-order kinematic coefficient for the angle of link 3 is mm θ 3 = =+.165 rad / rad 00 mm (8) The positive sign indicates that link 3 is rotating counterclockwise for a counterclockwise rotation of the input link. From Cramer s rule, the first-order kinematic coefficient for point B is mm R 9 = = mm / rad 00 mm (9a) Therefore, the first-order kinematic coefficient for point B is R 9 = 1.0m/rad (9b) The negative sign indicates that the length of the vector R 9 is becoming shorter for a counterclockwise rotation of the input link, that is point B is moving downward. The rolling contact constraint between link and the ground link 1 can be written as ± Δ R = ρ ( Δθ Δ θ ) (10) 9 7 The correct sign is positive because as the wheel rotates counterclockwise the magnitude of the vector R 9 becomes longer. Also, the change in the angular position of the vector R 7 is zero, that is, Δ θ7 = 0, therefore, Equation (10) can be written as + Δ R9 = ρδ θ (11) 15
16 Differentiating Equation (11) with respect to the input position θ gives + R = ρ θ (1a) 9 Then rearranging this equation, the first-order kinematic coefficient for link can be written as θ R 9 =+ (1b) ρ Substituting Equation (9b) and the radius of link into Equation (1b), the first-order kinematic coefficient for link is ( mm) θ =+ = 7.13 rad/rad (13) 10 mm The negative sign indicates that link is rotating clockwise as the input link rotates counterclockwise. (iii) Points. The angular velocity of link 3 can be written as ω 3 =θ 3 ω (1a) Substituting Equation (8) and the given angular velocity of the input link into Equation (1a), the angular velocity of link 3 is ω 3 = ( rad / rad) ( 50 rad / s) = rad / s (1b) The positive sign indicates that link 3 is rotating counterclockwise as the input link rotates counterclockwise. The angular velocity of link can be written as ω =θ ω (15a) Substituting Equation (13b) and the given angular velocity of the input link into Equation (15a), the angular velocity of link 3 is ω = ( 7.13 rad / rad) (50 rad / s) = rad / s (15b) The negative sign indicates that link is rotating clockwise as the input link rotates counterclockwise. (iv) 3 Points. The velocity of point B fixed in link can be written as VB = R 9 ω (16a) Substituting Equation (9b) and the given angular velocity of the input link into Equation (16a), the velocity of point B is V = ( 1.0 m / rad)(50 rad / s) = 50 m / s (16b) B The negative sign indicates that the velocity of point B is directed downward from point B as the input link rotates counterclockwise, that is VB = 50 j m/s (17) 16
ME Machine Design I. EXAM 1. OPEN BOOK AND CLOSED NOTES. Wednesday, September 30th, 2009
ME - Machine Design I Fall Semester 009 Name Lab. Div. EXAM. OPEN BOOK AND CLOSED NOTES. Wednesday, September 0th, 009 Please use the blank paper provided for your solutions. Write on one side of the paper
More informationEXAM 1. OPEN BOOK AND CLOSED NOTES Thursday, February 18th, 2010
ME 35 - Machine Design I Spring Semester 010 Name of Student Lab. Div. Number EXAM 1. OPEN BOOK AND CLOSED NOTES Thursday, February 18th, 010 Please use the blank paper provided for your solutions. Write
More informationFigure 1. A planar mechanism. 1
ME 352 - Machine Design I Summer Semester 201 Name of Student Lab Section Number EXAM 1. OPEN BOOK AND CLOSED NOTES. Wednesday, July 2nd, 201 Use the blank paper provided for your solutions. Write on one
More informationNamee of Student. link and I R 2 ?? = 0. and Δ θ. Calculate the. in the next. iteration. 1. = 6cm and θ * 9 = 135.
ME 52 - Machine Design I Fall Semester 2010 EXAM 1. OPEN BOOK AND CLOSED NOTES. Namee of Student Lab. Div. Number Wednesday, September 29th, 2010 Use the blank paper provided for your solutions. Write
More information1. This is a CLOSED BOOK, CLOSED NOTES exam. A list of equations for your reference is provided below.
_ Instructions 1. This is a CLOSED BOOK, CLOSED NOTES exam. A list of equations for your reference is provided below. 2. Begin each problem on the printed sheet and continue on the lined paper provided.
More informationFigure 1a. A planar mechanism.
ME 5 - Machine Design I Fall Semester 0 Name f Student Lab Sectin Number EXAM. OPEN BOOK AND CLOSED NOTES. Mnday, September rd, 0 Write n ne side nly f the paper prvided fr yur slutins. Where necessary,
More informationof the four-bar linkage shown in Figure 1 is T 12
ME 5 - Machine Design I Fall Semester 0 Name of Student Lab Section Number FINL EM. OPEN BOOK ND CLOSED NOTES Wednesday, December th, 0 Use the blank paper provided for your solutions write on one side
More informationME Machine Design I
ME 5 - Machine Design I Summer Semester 008 Name Lab. Div. EXAM. OEN BOOK AND CLOSED NOTES. Wednesday, July 16th, 008 Write your solutions on the blank paper that is provided. Write on one side of the
More informationRELATIVE MOTION ANALYSIS: VELOCITY (Section 16.5)
RELATIVE MOTION ANALYSIS: VELOCITY (Section 16.5) Today s Objectives: Students will be able to: a) Describe the velocity of a rigid body in terms of translation and rotation components. b) Perform a relative-motion
More informationDynamics Plane kinematics of rigid bodies Section 4: TJW Rotation: Example 1
Section 4: TJW Rotation: Example 1 The pinion A of the hoist motor drives gear B, which is attached to the hoisting drum. The load L is lifted from its rest position and acquires an upward velocity of
More informationPlanar Rigid Body Kinematics Homework
Chapter 2 Planar Rigid ody Kinematics Homework Freeform c 2016 2-1 2-2 Freeform c 2016 Homework 2. Given: The pulley shown below freely rotates about point C and interacts with two rubber belts (one horizontal,
More informationExam 1 January 31, 2012
Exam 1 Instructions: You have 60 minutes to complete this exam. This is a closed-book, closed-notes exam. You are allowed to use a calculator during the exam. Usage of mobile phones and other electronic
More informationPlanar Rigid Body Kinematics Homework
Chapter 2: Planar Rigid ody Kinematics Homework Chapter 2 Planar Rigid ody Kinematics Homework Freeform c 2018 2-1 Chapter 2: Planar Rigid ody Kinematics Homework 2-2 Freeform c 2018 Chapter 2: Planar
More informationME Machine Design I. FINAL EXAM. OPEN BOOK AND CLOSED NOTES. Friday, May 8th, 2009
ME 5 - Machine Design I Spring Seester 009 Nae Lab. Div. FINAL EXAM. OPEN BOOK AND LOSED NOTES. Friday, May 8th, 009 Please use the blank paper for your solutions. Write on one side of the paper only.
More informationFinal Exam April 30, 2013
Final Exam Instructions: You have 120 minutes to complete this exam. This is a closed-book, closed-notes exam. You are allowed to use a calculator during the exam. Usage of mobile phones and other electronic
More informationME Machine Design I
ME 35 - Machine Design I Summer Semester 008 Name Lab. Div. FINAL EXAM. OPEN BOOK AND CLOSED NOTES. Wednesday, July 30th, 008 Please show all your work for your solutions on the blank white paper. Write
More informationFinal Exam December 15, 2014
Final Exam Instructions: You have 120 minutes to complete this exam. This is a closed-book, closed-notes exam. You are allowed to use the ME approved calculator only during the exam. Usage of mobile phones
More informationExam 1 September 11, 2013
Exam 1 Instructions: You have 60 minutes to complete this exam. This is a closed-book, closed-notes exam. You are allowed to use an approved calculator during the exam. Usage of mobile phones and other
More informationPLANAR RIGID BODY MOTION: TRANSLATION &
PLANAR RIGID BODY MOTION: TRANSLATION & Today s Objectives : ROTATION Students will be able to: 1. Analyze the kinematics of a rigid body undergoing planar translation or rotation about a fixed axis. In-Class
More informationUNIVERSITY OF SASKATCHEWAN GE MECHANICS III MIDTERM EXAM FEBRUARY 13, 2008 A. Dolovich & H. Huenison A CLOSED BOOK EXAMINATION TIME: 2 HOURS
UNIVERSITY OF SASKATCHEWAN GE 226.3 MECHANICS III MIDTERM EXAM FEBRUARY 13, 2008 A. Dolovich & H. Huenison A CLOSED BOOK EXAMINATION TIME: 2 HOURS LAST NAME (printed): FIRST NAME (printed): STUDENT NUMBER:
More informationRIGID BODY MOTION (Section 16.1)
RIGID BODY MOTION (Section 16.1) There are cases where an object cannot be treated as a particle. In these cases the size or shape of the body must be considered. Rotation of the body about its center
More informationFind: Determine the velocity and acceleration of end P. Write your answers as vectors.
Homework 2. Given: ar P rotates about a shaft passing through end of the bar. t the instant shown, the angular velocity and angular acceleration of P are given by ω and α. atics Homework Problems ME 274
More informationEDEXCEL NATIONAL CERTIFICATE/DIPLOMA ADVANCED MECHANICAL PRINCIPLES AND APPLICATIONS UNIT 18 NQF LEVEL 3
EDEXCEL NATIONAL CERTIFICATE/DIPLOMA ADVANCED MECHANICAL PRINCIPLES AND APPLICATIONS UNIT 18 NQF LEVEL 3 OUTCOME 3 BE ABLE TO DETERMINE RELATIVE AND RESULTANT VELOCITY IN ENGINEERING SYSTEMS Resultant
More informationPROBLEM rad/s r. v = ft/s
PROLEM 15.38 An automobile traels to the right at a constant speed of 48 mi/h. If the diameter of a wheel is 22 in., determine the elocities of Points, C,, and E on the rim of the wheel. A 48 mi/h 70.4
More informationLecture 18. PLANAR KINEMATICS OF RIGID BODIES, GOVERNING EQUATIONS
Lecture 18. PLANAR KINEMATICS OF RIGID BODIES, GOVERNING EQUATIONS Planar kinematics of rigid bodies involve no new equations. The particle kinematics results of Chapter 2 will be used. Figure 4.1 Planar
More informationUNIT 2 KINEMATICS OF LINKAGE MECHANISMS
UNIT 2 KINEMATICS OF LINKAGE MECHANISMS ABSOLUTE AND RELATIVE VELOCITY An absolute velocity is the velocity of a point measured from a fixed point (normally the ground or anything rigidly attached to the
More informationPlane Motion of Rigid Bodies: Forces and Accelerations
Plane Motion of Rigid Bodies: Forces and Accelerations Reference: Beer, Ferdinand P. et al, Vector Mechanics for Engineers : Dynamics, 8 th Edition, Mc GrawHill Hibbeler R.C., Engineering Mechanics: Dynamics,
More informationUNIVERSITY OF SASKATCHEWAN GE MECHANICS III FINAL EXAM APRIL 18, 2011 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS
UNIVERSITY OF SASKATCHEWAN GE 226.3 MECHANICS III FINAL EXAM APRIL 18, 2011 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS LAST NAME (printed): FIRST NAME (printed): STUDENT NUMBER: EXAMINATION
More informationReview of Engineering Dynamics
Review of Engineering Dynamics Part 1: Kinematics of Particles and Rigid Bodies by James Doane, PhD, PE Contents 1.0 Course Overview... 4.0 Basic Introductory Concepts... 4.1 Introduction... 4.1.1 Vectors
More informationEQUATIONS OF MOTION: CYLINDRICAL COORDINATES (Section 13.6)
EQUATIONS OF MOTION: CYLINDRICAL COORDINATES (Section 13.6) Today s Objectives: Students will be able to analyze the kinetics of a particle using cylindrical coordinates. APPLICATIONS The forces acting
More informationChapter 10 Rotational Kinematics and Energy. Copyright 2010 Pearson Education, Inc.
Chapter 10 Rotational Kinematics and Energy Copyright 010 Pearson Education, Inc. 10-1 Angular Position, Velocity, and Acceleration Copyright 010 Pearson Education, Inc. 10-1 Angular Position, Velocity,
More informationUnit Circle: The unit circle has radius 1 unit and is centred at the origin on the Cartesian plane. POA
The Unit Circle Unit Circle: The unit circle has radius 1 unit and is centred at the origin on the Cartesian plane THE EQUATION OF THE UNIT CIRCLE Consider any point P on the unit circle with coordinates
More informationEQUATIONS OF MOTION: ROTATION ABOUT A FIXED AXIS (Section 17.4) Today s Objectives: Students will be able to analyze the planar kinetics of a rigid
EQUATIONS OF MOTION: ROTATION ABOUT A FIXED AXIS (Section 17.4) Today s Objectives: Students will be able to analyze the planar kinetics of a rigid body undergoing rotational motion. APPLICATIONS The crank
More information20k rad/s and 2 10k rad/s,
ME 35 - Machine Design I Summer Semester 0 Name of Student: Lab Section Number: FINAL EXAM. OPEN BOOK AND CLOSED NOTES. Thursday, August nd, 0 Please show all your work for your solutions on the blank
More informationMoving Reference Frame Kinematics Homework
Chapter 3 Moving Reference Frame Kinematics Homework Freeform c 2016 3-1 3-2 Freeform c 2016 Homework 3. Given: n L-shaped telescoping arm is pinned to ground at point. The arm is rotating counterclockwise
More informationUNIT II Fig (1) Fig (1)
UNIVERSITY OF PUNE [4362]-116 S.E.(Mechanical / Automobile) Examination 2013 (2008 pattern) THEY OF MACHINES -1 [Total No. of Questions: 12] [Total No. of Printed pages: 7] [Time: 4 Hours] [Max. Marks:
More informationChapter 8 Lecture. Pearson Physics. Rotational Motion and Equilibrium. Prepared by Chris Chiaverina Pearson Education, Inc.
Chapter 8 Lecture Pearson Physics Rotational Motion and Equilibrium Prepared by Chris Chiaverina Chapter Contents Describing Angular Motion Rolling Motion and the Moment of Inertia Torque Static Equilibrium
More informationTAM 212 Worksheet 5: Car steering
Name: Group members: TM 212 Worksheet 5: ar steering This worksheet aims to understand how cars steer. The #avs webpage on Steering geometry illustrates the basic ideas. On the diagram below, the kingpins
More informationME 274 Spring 2017 Examination No. 2 PROBLEM No. 2 (20 pts.) Given:
PROBLEM No. 2 (20 pts.) Given: Blocks A and B (having masses of 2m and m, respectively) are connected by an inextensible cable, with the cable being pulled over a small pulley of negligible mass. Block
More informationExam 2 October 17, 2013
Exam 2 Instructions: You have 60 minutes to complete this exam. This is a closed-book, closed-notes exam. You are allowed to use an approved calculator during the exam. Usage of mobile phones and other
More informationThe University of Melbourne Engineering Mechanics
The University of Melbourne 436-291 Engineering Mechanics Tutorial Eleven Instantaneous Centre and General Motion Part A (Introductory) 1. (Problem 5/93 from Meriam and Kraige - Dynamics) For the instant
More informationCEE 271: Applied Mechanics II, Dynamics Lecture 25: Ch.17, Sec.4-5
1 / 36 CEE 271: Applied Mechanics II, Dynamics Lecture 25: Ch.17, Sec.4-5 Prof. Albert S. Kim Civil and Environmental Engineering, University of Hawaii at Manoa Date: 2 / 36 EQUATIONS OF MOTION: ROTATION
More information1. Trigonometry.notebook. September 29, Trigonometry. hypotenuse opposite. Recall: adjacent
Trigonometry Recall: hypotenuse opposite adjacent 1 There are 3 other ratios: the reciprocals of sine, cosine and tangent. Secant: Cosecant: (cosec θ) Cotangent: 2 Example: Determine the value of x. a)
More informationPLANAR KINETICS OF A RIGID BODY: WORK AND ENERGY Today s Objectives: Students will be able to: 1. Define the various ways a force and couple do work.
PLANAR KINETICS OF A RIGID BODY: WORK AND ENERGY Today s Objectives: Students will be able to: 1. Define the various ways a force and couple do work. In-Class Activities: 2. Apply the principle of work
More informationCEE 271: Applied Mechanics II, Dynamics Lecture 23: Ch.16, Sec.7
1 / 26 CEE 271: Applied Mechanics II, Dynamics Lecture 23: Ch.16, Sec.7 Prof. Albert S. Kim Civil and Environmental Engineering, University of Hawaii at Manoa Tuesday, Nov. 8, 2012 2 / 26 RELATIVE MOTION
More informationChapter 8 Acceleration in Mechanisms
Chapter 8 Acceleration in Mechanisms 1 2 8.2. Acceleration Diagram for a Link Example 8.1 3 The crank of a slider crank mechanism rotates cw at a constant speed of 300 rpm. The crank is 150 mm & the ConRod
More informationRigid Body Kinetics :: Virtual Work
Rigid Body Kinetics :: Virtual Work Work-energy relation for an infinitesimal displacement: du = dt + dv (du :: total work done by all active forces) For interconnected systems, differential change in
More informationPlease circle the name of your instructor: EB01: Beamish EB02: Fenrich EB03: Ruhl. EB04: Rahman EB05: Nedie EB06: Ropchan LAST NAME: FIRST NAME: ID#:
Faculty of Engineering and Department of Physics ENPH 131 Final Examination Saturday, April 20, 2013; 2:00 pm 4:30 pm Universiade Pavilion Section EB01 (BEAMISH): Rows 1, 3, 5(seats 1-45) Section EB02
More informationChapter 10 Practice Test
Chapter 10 Practice Test 1. At t = 0, a wheel rotating about a fixed axis at a constant angular acceleration of 0.40 rad/s 2 has an angular velocity of 1.5 rad/s and an angular position of 2.3 rad. What
More informationPosition: Angular position =! = s r. Displacement: Angular displacement =!" = " 2
Chapter 11 Rotation Perfectly Rigid Objects fixed shape throughout motion Rotation of rigid bodies about a fixed axis of rotation. In pure rotational motion: every point on the body moves in a circle who
More informationENGR DYNAMICS. Rigid-body Lecture 4. Relative motion analysis: acceleration. Acknowledgements
ENGR 2030 -DYNAMICS Rigid-body Lecture 4 Relative motion analysis: acceleration Acknowledgements These lecture slides were provided by, and are the copyright of, Prentice Hall (*) as part of the online
More informationMHS. Applied Math. Sample Questions. Exam to go from grade 11 to grade 12
MHS Applied Math Exam to go from grade 11 to grade 1 Sample Questions 1. OP + PA + AR = 1. OPAR. AR 3. OR. Given two vectors u and v in the box below, how can we correctly find their sum, u + v, using
More informationDYNAMICS ME HOMEWORK PROBLEM SETS
DYNAMICS ME 34010 HOMEWORK PROBLEM SETS Mahmoud M. Safadi 1, M.B. Rubin 2 1 safadi@technion.ac.il, 2 mbrubin@technion.ac.il Faculty of Mechanical Engineering Technion Israel Institute of Technology Spring
More informationName: SOLUTIONS Date: 09/07/2017. M20550 Calculus III Tutorial Worksheet 2
M20550 Calculus III Tutorial Worksheet 2 1. Find an equation of the plane passes through the point (1, 1, 7) and perpendicular to the line x = 1 + 4t, y = 1 t, z = 3. Solution: To write an equation of
More information6. Find the net torque on the wheel in Figure about the axle through O if a = 10.0 cm and b = 25.0 cm.
1. During a certain period of time, the angular position of a swinging door is described by θ = 5.00 + 10.0t + 2.00t 2, where θ is in radians and t is in seconds. Determine the angular position, angular
More informationME 274: Basic Mechanics II Spring April 18, Problem 1 (24 points):
Problem 1 (24 points): Given: The block shown in the figure slides on a smooth surface. A thin homogenous bar is attached to the block and is free to rotate about a pin joint at A. At the instant shown
More informationThe choice of origin, axes, and length is completely arbitrary.
Polar Coordinates There are many ways to mark points in the plane or in 3-dim space for purposes of navigation. In the familiar rectangular coordinate system, a point is chosen as the origin and a perpendicular
More informationComplete the table by filling in the symbols and equations. Include any notes that will help you remember and understand what these terms mean.
AP Physics Rotational kinematics Rotational Kinematics Complete the table by filling in the symbols and equations. Include any notes that will help you remember and understand what these terms mean. Translational
More informationKinematics of Machines Prof. A. K. Mallik Department of Mechanical Engineering Indian Institute of Technology, Kanpur
Kinematics of Machines Prof. A. K. Mallik Department of Mechanical Engineering Indian Institute of Technology, Kanpur Module - 5 Lecture - 1 Velocity and Acceleration Analysis The topic of today s lecture
More informationProblem 1 Problem 2 Problem 3 Problem 4 Total
Name Section THE PENNSYLVANIA STATE UNIVERSITY Department of Engineering Science and Mechanics Engineering Mechanics 12 Final Exam May 5, 2003 8:00 9:50 am (110 minutes) Problem 1 Problem 2 Problem 3 Problem
More informationChapter 10. Rotation of a Rigid Object about a Fixed Axis
Chapter 10 Rotation of a Rigid Object about a Fixed Axis Angular Position Axis of rotation is the center of the disc Choose a fixed reference line. Point P is at a fixed distance r from the origin. A small
More informationKinematics, Dynamics, and Vibrations FE Review Session. Dr. David Herrin March 27, 2012
Kinematics, Dynamics, and Vibrations FE Review Session Dr. David Herrin March 7, 0 Example A 0 g ball is released vertically from a height of 0 m. The ball strikes a horizontal surface and bounces back.
More informationTorque. Physics 6A. Prepared by Vince Zaccone For Campus Learning Assistance Services at UCSB
Physics 6A Torque is what causes angular acceleration (just like a force causes linear acceleration) Torque is what causes angular acceleration (just like a force causes linear acceleration) For a torque
More informationPrecalculus Notes: Unit 6 Vectors, Parametrics, Polars, & Complex Numbers. A: Initial Point (start); B: Terminal Point (end) : ( ) ( )
Syllabus Objectives: 5.1 The student will explore methods of vector addition and subtraction. 5. The student will develop strategies for computing a vector s direction angle and magnitude given its coordinates.
More informationReview for 3 rd Midterm
Review for 3 rd Midterm Midterm is on 4/19 at 7:30pm in the same rooms as before You are allowed one double sided sheet of paper with any handwritten notes you like. The moment-of-inertia about the center-of-mass
More informationP4 Kinematics Dr Alexander M. Korsunsky Hilary Term 2001
P4 Kinematics Dr Alexander M. Korsunsky Hilary Term 001 LR1 Thom Building Wk 5: M. 11, T. 1, Th. 1 Wk 6: M. 11-1 - Scope of the lecture course: 1. Kinematics of particles Basic definitions and revision
More informationFALL TERM EXAM, PHYS 1211, INTRODUCTORY PHYSICS I Thursday, 11 December 2014, 6 PM to 9 PM, Field House Gym
FALL TERM EXAM, PHYS 1211, INTRODUCTORY PHYSICS I Thursday, 11 December 2014, 6 PM to 9 PM, Field House Gym NAME: STUDENT ID: INSTRUCTION 1. This exam booklet has 13 pages. Make sure none are missing 2.
More information3. ANALYTICAL KINEMATICS
In planar mechanisms, kinematic analysis can be performed either analytically or graphically In this course we first discuss analytical kinematic analysis nalytical kinematics is based on projecting the
More informationENGR220 Dynamics. Final Exam
Spring Semester 2006 1 ENGR220 Dynamics Final Exam Instructions: 110 minutes to complete. Closed-book, 4 exam reference sheets allowed. Turn computations and exam in to instructor at the end of the exam
More informationMECHANICAL ENGINEERING
MECHNICL ENGINEERING ESE TOPICWISE OBJECTIVE SOLVED PPER-II FROM (1995-017) UPSC Engineering Services Examination State Engineering Service Examination & Public Sector Examination. IES MSTER PUBLICTION
More informationChapter 3. Radian Measure and Circular Functions. Copyright 2005 Pearson Education, Inc.
Chapter 3 Radian Measure and Circular Functions Copyright 2005 Pearson Education, Inc. 3.1 Radian Measure Copyright 2005 Pearson Education, Inc. Measuring Angles Thus far we have measured angles in degrees
More informationUNIT 15 ROTATION KINEMATICS. Objectives
UNIT 5 ROTATION KINEMATICS Objectives to understand the concept of angular speed to understand the concept of angular acceleration to understand and be able to use kinematics equations to describe the
More informationPreview from Notesale.co.uk Page 2 of 42
. CONCEPTS & FORMULAS. INTRODUCTION Radian The angle subtended at centre of a circle by an arc of length equal to the radius of the circle is radian r o = o radian r r o radian = o = 6 Positive & Negative
More informationUNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS International General Certificate of Secondary Education
UNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS International General Certificate of Secondary Education ADDITIONAL MATHEMATICS 0606/02 Paper 2 Examination from 2013 SPECIMEN PAPER 2 hours Candidates
More informationChapter 3 HW Solution
Chapter 3 HW Solution Problem 3.6: I placed an xy coordinate system at a convenient point (origin doesn t really matter). y 173 x The positions of both planes are given by r B = v B ti + 173j mi (1) r
More informationRobotics I. Figure 1: Initial placement of a rigid thin rod of length L in an absolute reference frame.
Robotics I September, 7 Exercise Consider the rigid body in Fig., a thin rod of length L. The rod will be rotated by an angle α around the z axis, then by an angle β around the resulting x axis, and finally
More informationDYNAMICS. Kinematics of Rigid Bodies VECTOR MECHANICS FOR ENGINEERS: Tenth Edition CHAPTER
Tenth E CHAPTER 15 VECTOR MECHANICS FOR ENGINEERS: DYNAMICS Ferdinand P. Beer E. Russell Johnston, Jr. Phillip J. Cornwell Lecture Notes: Brian P. Self California Polytechnic State University Kinematics
More informationChapter 3 Velocity Analysis
Chapter 3 Velocity nalysis The position of point with respect to 0, Fig 1 may be defined mathematically in either polar or Cartesian form. Two scalar quantities, the length R and the angle θ with respect
More informationTranslational vs Rotational. m x. Connection Δ = = = = = = Δ = = = = = = Δ =Δ = = = = = 2 / 1/2. Work
Translational vs Rotational / / 1/ Δ m x v dx dt a dv dt F ma p mv KE mv Work Fd / / 1/ θ ω θ α ω τ α ω ω τθ Δ I d dt d dt I L I KE I Work / θ ω α τ Δ Δ c t s r v r a v r a r Fr L pr Connection Translational
More informationRotational Motion. Lecture 17. Chapter 10. Physics I Department of Physics and Applied Physics
Lecture 17 Chapter 10 Physics I 11.13.2013 otational Motion Torque Course website: http://faculty.uml.edu/andriy_danylov/teaching/physicsi Lecture Capture: http://echo360.uml.edu/danylov2013/physics1fall.html
More informationKinematics of. Motion. 8 l Theory of Machines
8 l Theory of Machines Features 1. 1ntroduction.. Plane Motion. 3. Rectilinear Motion. 4. Curvilinear Motion. 5. Linear Displacement. 6. Linear Velocity. 7. Linear Acceleration. 8. Equations of Linear
More informationMath Section 4.3 Unit Circle Trigonometry
Math 10 - Section 4. Unit Circle Trigonometry An angle is in standard position if its vertex is at the origin and its initial side is along the positive x axis. Positive angles are measured counterclockwise
More informationPractice Test 3. Name: Date: ID: A. Multiple Choice Identify the choice that best completes the statement or answers the question.
Name: Date: _ Practice Test 3 Multiple Choice Identify the choice that best completes the statement or answers the question. 1. A wheel rotates about a fixed axis with an initial angular velocity of 20
More informationPHYSICS 149: Lecture 21
PHYSICS 149: Lecture 21 Chapter 8: Torque and Angular Momentum 8.2 Torque 8.4 Equilibrium Revisited 8.8 Angular Momentum Lecture 21 Purdue University, Physics 149 1 Midterm Exam 2 Wednesday, April 6, 6:30
More informationLecture 19. ROLLING WITHOUT SLIPPING. Figure 4.8 Gear rolling in geared horizontal guides. Figure 4.9 Wheel rolling on a horizontal surface.
Lecture 19. ROLLING WITHOUT SLIPPING Figure 4.8 Gear rolling in geared horizontal guides. Figure 4.9 Wheel rolling on a horizontal surface. The derivation and understanding of velocity and acceleration
More informationRotational Kinematics
Rotational Kinematics Rotational Coordinates Ridged objects require six numbers to describe their position and orientation: 3 coordinates 3 axes of rotation Rotational Coordinates Use an angle θ to describe
More informationPROBLEM 16.4 SOLUTION
PROBLEM 16.4 The motion of the.5-kg rod AB is guided b two small wheels which roll freel in horizontal slots. If a force P of magnitude 8 N is applied at B, determine (a) the acceleration of the rod, (b)
More informationDate: 1 April (1) The only reference material you may use is one 8½x11 crib sheet and a calculator.
PH1140: Oscillations and Waves Name: Solutions Conference: Date: 1 April 2005 EXAM #1: D2005 INSTRUCTIONS: (1) The only reference material you may use is one 8½x11 crib sheet and a calculator. (2) Show
More information7.1 Describing Circular and Rotational Motion.notebook November 03, 2017
Describing Circular and Rotational Motion Rotational motion is the motion of objects that spin about an axis. Section 7.1 Describing Circular and Rotational Motion We use the angle θ from the positive
More informationMath 30-1: Trigonometry One PRACTICE EXAM
Math 30-1: Trigonometry One PRACTICE EXAM 1. The angle 210 is equivalent to: degrees radians degrees radians 2. The reference angle of is: radians radians radians radians 3. The principal angle of 9.00
More informationPhys101 Lectures 19, 20 Rotational Motion
Phys101 Lectures 19, 20 Rotational Motion Key points: Angular and Linear Quantities Rotational Dynamics; Torque and Moment of Inertia Rotational Kinetic Energy Ref: 10-1,2,3,4,5,6,8,9. Page 1 Angular Quantities
More informationDate: 31 March (1) The only reference material you may use is one 8½x11 crib sheet and a calculator.
PH1140: Oscillations and Waves Name: SOLUTIONS AT END Conference: Date: 31 March 2005 EXAM #1: D2006 INSTRUCTIONS: (1) The only reference material you may use is one 8½x11 crib sheet and a calculator.
More informationMoving Reference Frame Kinematics Homework
Chapter 3 Moving Reference Frame Kinematics Homework Freeform c 2018 3-1 3-2 Freeform c 2018 Homework H.3. Given: The disk shown is rotating about its center with a constant rotation rate of Ω. Four slots
More informationFor the instant shown, a) determine the angular velocity of link OA. b) determine the speed of D. c) determine the angular acceleration of link OA.
ME 74 Fall 008 PROBLEM NO. 1 Given: mechanism is made up of lins O, B and BD, with all three lins joined at pin. Lin O is pinned to ground at end O, end D of D is constrained to vertical motion only, and
More informationGeneral Physics I. Lecture 8: Rotation of a Rigid Object About a Fixed Axis. Prof. WAN, Xin ( 万歆 )
General Physics I Lecture 8: Rotation of a Rigid Object About a Fixed Axis Prof. WAN, Xin ( 万歆 ) xinwan@zju.edu.cn http://zimp.zju.edu.cn/~xinwan/ New Territory Object In the past, point particle (no rotation,
More informationA2 Assignment zeta Cover Sheet. C3 Differentiation all methods. C3 Sketch and find range. C3 Integration by inspection. C3 Rcos(x-a) max and min
A Assignment zeta Cover Sheet Name: Question Done Backpack Ready? Topic Comment Drill Consolidation M1 Prac Ch all Aa Ab Ac Ad Ae Af Ag Ah Ba C3 Modulus function Bb C3 Modulus function Bc C3 Modulus function
More informationMechanism Design. Transmission angle of mechanism
Mechanism Design Transmission angle of mechanism Transmission angle of mechanism It would be useful to have a measure, criterion, or index of how well a mechanisms might run *. The transmission angle is
More informationPhysics 121, Final Exam Do not turn the pages of the exam until you are instructed to do so.
, Final Exam Do not turn the pages of the exam until you are instructed to do so. You are responsible for reading the following rules carefully before beginning. Exam rules: You may use only a writing
More informationChapter 8. Rotational Kinematics
Chapter 8 Rotational Kinematics 8.1 Rotational Motion and Angular Displacement In the simplest kind of rotation, points on a rigid object move on circular paths around an axis of rotation. 8.1 Rotational
More informationChapter 5 Trigonometric Functions of Angles
Chapter 5 Trigonometric Functions of Angles Section 3 Points on Circles Using Sine and Cosine Signs Signs I Signs (+, +) I Signs II (+, +) I Signs II (, +) (+, +) I Signs II (, +) (+, +) I III Signs II
More information