Fault Detection and Isolation of the Wind Turbine Benchmark: an Estimation-based Approach
|
|
- Molly Barber
- 5 years ago
- Views:
Transcription
1 Milano (Italy) August - September, 11 Fault Detection and Isolation of the Wind Turbine Benchmark: an Estimation-based Approach Xiaodong Zhang, Qi Zhang Songling Zhao Riccardo Ferrari Marios M. Polycarpou,andThomas Parisini Dept. of Electrical Engineering, Wright State University, USA Danieli Automation, Buttrio (UD), Italy Dept. of Electrical and Computer Engineering, University of Cyprus, Cyprus Imperial College London (UK) and University of Trieste (Italy) Abstract: In this paper, a fault detection and isolation (FDI) method is developed for wind turbines based on a benchmark system model. The FDI method follows a general architecture developed in previous papers, where a fault detection estimator is used for fault detection, and a bank of fault isolation estimators are employed to determine the particular fault type/location. Each isolation estimator is designed based on a particular fault scenario under consideration. Some representative simulation results are given to show the effectiveness of the FDI method. 1. INTRODUCTION. BENCHMARK SYSTEM DESCRIPTION.1 System Overview As one of the alternative energy sources, wind turbines are starting to contribute to a more significant part of the world s power production. The wind turbines need to operate reliably at all times, despite the possible occurrence of faulty system components and sensors. Therefore, the design of fault diagnosis and accommodation techniques is a crucial step in achieving reliable operations of wind turbines. During the last two decades, there has been significant research activity in the design and analysis of fault diagnosis and accommodation schemes (see, for instance, Blanke, et al. [], Gertler [199]). Several researchers have also investigated wind turbine fault diagnostics (e.g., Dobrila and Stefansen [7], Hameeda et al. [9], Odgaard and Stoustrup [9], Wei et al. []). The main challenges of FDI design for wind turbines include: (1) the aerodynamic rotor torque is not measured; and () the wind speed is only measured at the hub position with high noise. In this paper, a fault diagnosis method is presented for wind turbines by utilizing the benchmark system model developed by Odgaard et al. [9]. The FDI architecture follows the general methodology presented in previous papers by Zhang et al. [, ]. A fault detection estimator is used to monitor the occurrence of a fault, and a bank of fault isolation estimators are employed to determine the particular fault type/location. Each isolation estimator is designed based on a particular fault scenario under consideration. The paper is organized as follows. Section introduces the wind turbine benchmark system used for this research work. The general FDI architecture is given in Section 3. Sections - describe the FDI method for the pitch systems, the drive train, and converter, respectively. Some representative simulation results are given in Section 7. Finally, some concluding remarks are given in Section. A wind turbine converts wind energy to electrical energy. In the benchmark model developed by Odgaard et al. [9], a three blade horizontal axis turbine is considered. The wind turbine benchmark model mainly consists of four components: blade and pitch system, drive train, generator and converter, and controller. The blades connected to the rotor shaft are facing the wind direction, and the wind turns the wind turbine blades around. A generator fully coupled to a converter is used to convert the mechanical energy to electrical energy. In order to upscale the rotational speed to the needed value at the generator, a drive train is introduced. The converter can be used to set the generator torque, which consequently can be used to control the rotational speeds of the generator and the rotor. The conversion from wind energy to mechanical energy is controlled by pitching the blades or by controlling the rotational speed of the turbine relative to the wind speed. The controller is designed to make the system track a given power reference.. System Model Each of the three hydraulic pitch systems is represented by its closed-loop system dynamics. The state space representation of the nominal pitch system dynamics is: ẋ pb = A pb x pb + B pb (β r + β f ) y pb = C pb x pb (1) where the state vector x pb =[ βi β i ] is comprised of the pitch angular speed β i and position β i (i =1,, 3), and y pb R is the measured pitch position, β r R is the reference position signal provided by the controller, and β f R is an internal variable used to model the pitch position error caused by sensor faults. The values of the (A pb,b pb,c pb ) triple are defined in the benchmark model. For redundancy consideration, each of three pitch positions Copyright by the International Federation of Automatic Control (IFAC) 95
2 Milano (Italy) August - September, 11 is measured with two identical sensors, represented by β i,m1 and β i,m, i =1,, 3, respectively. The nominal dynamics of the drive train are described by [ ] τr ẋ dt = A dt x dt + B dt τ g () y dt = C dt x dt where the state vector x dt = [ωr ω g θ Δ ] includes the rotor speed ω r, the generator speed ω g, and the torsion angle of the drive train θ Δ. The input signals are the aerodynamic rotor torque τ r and the generator torque τ g. The output y dt represents measured speeds of the rotor and the generator. For redundancy consideration, the generator speed and rotor speed are measured with two identical sensors, respectively. Specifically, ω r,m1 and ω r,m are the two rotor speed measurements; and ω g,m1 and ω g,m are the two generator speed measurements..3 Fault Scenarios The following faults are considered in the wind turbine benchmark model. Faults in the pitch systems. Sensor faults in the pitch position measurements are either electrical or mechanical faults in the position sensors. Fault 1 is a fixed value sensor fault on pitch 1 position sensor 1(β 1,m1 ); Fault is a scaling error sensor fault on pitch position sensor (β,m ); Fault 3 is a fixed value sensor fault on pitch 3 position sensor 3 (β 3,m1 ). In addition, two actuator faults in the pitch systems are defined: Fault associated with pitch actuator caused by high air content in oil, and Fault 7 is associated with pitch actuator 3 caused by dropped main line pressure. Faults in the drive train system. Fault is a fixed value sensor fault on rotor speed sensor 1 (ω r,m1 ), and Fault 5 is a scaling error sensor affecting both rotor speed sensor and generator speed sensor (ω r,m, ω g,m ). Faults in the generator and converter system. Fault is a converter fault, representing an offset in the internal converter control loops. 3. FDI ARCHITECTURE In the benchmark model, it is assumed that only a single fault can possibly occur at any time. The presented FDI method is based on the general architecture developed in Zhang et al. []. The FDI architecture consists of a fault detection estimator (FDE) and a bank of N fault isolation estimators (FIEs), where N is the number of faults under consideration. The FDE is used to detect the occurrence of a fault, and the FIEs are used to determine the particular fault type/location that has occurred. Each FIE is designed based on a particular fault scenario or hypothesis under consideration. Fault Detection Decision Scheme: The decision on the occurrence of a fault (detection) is made when the modulus of at least one component of the fault detection residual exceeds its threshold. The fault isolation decision scheme is based on the following intuitive principle: for s = 1,, N, iffaults occurs at time T and is detected at time T d,thenasetof threshold can be designed for the s-th isolation estimator, such that each component of its output estimation error remains below its corresponding threshold, for all t>t d. Consequently, for each isolation estimator, such a set of thresholds can be associated with its output estimation error. In the fault isolation procedure, if for each isolation estimator r {1,,N}\{s}, at least one component of its output estimation error exceeds its threshold, then the possibility of the occurrence of fault r can be excluded. To summarize, we have the following: Fault Isolation Decision Scheme: Assume that fault s {1,...,N} occurs at time T andisdetectedattime T d. If, for each FIE r, r {1,,N}\{s},thereexist some finite time t r >T d, such that at least one component of its output estimation error exceeds the corresponding threshold, then the occurrence of fault s is concluded.. FDI METHOD FOR PITCH SYSTEMS In this section, we will present the FDI design for each pitch system by using the general architecture described above..1 Pitch System Faults The potential faults considered in the pitch systems include several sensor faults and actuator faults. Specifically, the faults considered in each pitch system of the benchmark model are: sensor fault 1 in pitch system 1, sensor fault and actuator fault in pitch system, as well as sensor fault 3 and actuator fault 7 in pitch system 3.. FDI Method for Pitch System 1 The objective of FDI design for Pitch system 1 is to timely detect and isolate a fixed value position fault in one of the two pitch position sensor signals (i.e., fault 1 in β 1,m1 or β 1,m ). Fault detection can be achieved by simply checking the consistency between these two sensor signals based on β 1,m1 β 1,m. After fault detection, in order to determine which sensor is faulty, two FIEs are designed. Each FIE is based on one of the following two possible fault scenarios: Case 1: Sensor is faulty, and sensor 1 is healthy; Case : Sensor 1 is faulty, and sensor is healthy As described above, the variable β f is used to model pitch position error as a result of sensor faults. For the ith pitch system, i =1,, 3, β f is given by β f = βi 1 (β i,m1 + β i,m ). (3) By substituting (3) into (1), we obtain ẋ pb = A pb x pb + B pb β r + B pb [β i 1 ] (β i,m1 + β i,m ) () Under the fault scenario 1 described above, we have β 1,m1 = β 1 = C pb x pb. (5) 9
3 Milano (Italy) August - September, 11 Thus, by using (1), (), and (5), the dynamics of pitch system 1 under fault scenario 1 is ẋ pb =(A pb +.5B pb C pb )x pb + B pb (β r.5β 1,m ) () β 1,m1 = C pb x pb. Analogously, under fault scenario, we have β 1,m = β 1 = C pb x pb, (7) and the dynamics of pitch system 1 under fault scenario is given by ẋ pb =(A pb +.5B pb C pb )x pb + B pb (β r.5β 1,m1 ) () β 1,m = C pb x pb. Therefore, based on () and (), the following two FIEs for pitch system 1 are chosen: ˆx 1 pb =(A pb +.5B pb C pb )ˆx 1 pb + B pb (β r.5β 1,m ) + L pb (β 1,m1 ˆβ 1,m1 ) ˆβ 1,m1 = C pbˆx 1 pb, (9) and ˆx pb =(A pb +.5B pb C pb )ˆx pb + B pb (β r.5β 1,m1 ) + L pb (β 1,m ˆβ 1,m ) ˆβ 1,m = C pbˆx pb, (1) where ˆβ 1,m1 is the estimate of output β 1,m1 provided by FIE 1, and ˆβ 1,m is the estimate of output β 1,m provided by FIE, and L pb is an observer gain matrix designed to make the matrix A pb +.5B pb C pb L pb C pb Hurwitz. Clearly, if sensor is faulty (i.e., fault scenario 1 is true), then the output estimation error β 1,m1 = β1,m1 ˆβ 1,m1 associated with FIE 1 converges to zeros. Analogously, if sensor 1 is faulty (i.e., fault scenario is true), then the output estimation error β 1,m = β1,m ˆβ 1,m associated with FIE converges to zeros. Hence, by following the fault isolation decision scheme described in Section 3, we have: If β 1,m1 is close to zero, and β 1,m significantly deviates from zero, then it is concluded that sensor is faulty; If β 1,m is close to zero, and β 1,m1 significantly deviates from zero, then it is concluded that sensor 1 is faulty..3 FDI Method for Pitch System The objective of FDI design for Pitch system is to timely detect and isolate the following two faults: A scaling error fault in one of the two pitch position sensor signals (i.e., fault in β,m1 or β,m ), An actuator fault caused by high air content in oil (i.e., fault ). Based on the FDI architecture described in Section 3, a FDE and two FIEs are designed. In the absence of faults, β f =. Thus, by using (1), the FDE is chosen as ˆx pb = A pb x pb + B pb β r + H pb (y pb ŷ pb ) (11) ŷ pb = C pbˆx pb, where ˆx pb and ŷ pb are the estimated system states and output, respectively, and H pb is the observer gain chosen to ensure the stability of the matrix A pb H pb C pb. Clearly, the output estimation error ỹ pb = ypb ŷ pb converges to zero in the absence of faults. By using similar methods as reported in Section., two FIEs are designed for pitch system. FIE 1 corresponds to the fault scenario of faulty sensor and generates a residual β,m1, and FIE corresponds to the fault scenario of faulty sensor 1 and generates a residual β,m (see (9) and (1)). Note that, for this specific problem under consideration, the fault isolation architecture is simplified by using two FIEs instead of three FIEs. After fault detection, if we can exclude the two cases of potential faulty sensors, then the occurrence of the third fault (i.e., actuator fault) considered is concluded. Specifically, the following fault isolation decision logic for pitch system is employed: If the residual β,m1 is close to zero, and β,m significantly deviates from zero, then it is concluded that sensor is faulty; If β,m is close to zero, and β,m1 significantly deviates from zero, then it is concluded that sensor 1 is faulty; If both β,m1 and β,m are significantly non-zero, then it is concluded that the actuator is faulty.. FDI Method for Pitch System 3 The objective of FDI design for Pitch system 3 is to timely detect and isolate the following two faults: A fixed error fault in one of the two pitch position sensor signals (i.e., fault 3 in β 3,m1 or β 3,m ). An actuator fault caused by low presure (i.e., fault 7) The FDI design can be carried out by following a similar method to that of pitch reported above. 5. FDI METHOD FOR DRIVE TRAIN SYSTEM 5.1 Drive Train Faults For the rotor and generator speed measurements in the drive train system, we consider the following sensor faults in the drive train system: A fixed value sensor fault on one of the rotor speed sensor (i.e., fault on ω r,m1 or ω r,m ), A scaling error sensor affecting one of the generator speed sensor (i.e., fault 5 on ω g,m1 or ω g,m ). 5. FDI Method for Rotor Speed Sensor Fault One of the difficult issues of FDI design for the drive train system is that the rotor speed ω r in () is controlled by the unknown aerodynamic rotor torque τ r. It is also difficult to accurately estimate τ r, since it involves the wind speed, which is only measured at the hub position with high noise. To overcome this issue, we note that in model (), the input matrix B dt and output matrix C dt take the forms of 97
4 Milano (Italy) August - September, 11 and B dt = C dt = 1 J r 1 J g, (1) [ ] 1, (13) 1 where J g and J r are the moment of inertia of the high speed shaft and rotor shaft. From (), (1), and (13), it is observed that the τ r only directly affects the first state variable ω r, which is measured. Therefore, by partitioning the state matrix A dt R 3 3 in () into: [ ] Adt1 A A dt = dt, A dt3 A dt where A dt R and A dt3 R 1,wehave [ ] [ ] ωg ωg = A θ dt + B Δ θ 1 τ g + B ω r (1) Δ with B 1 = [ 1 J g ] and B = A dt3. By defining the state vector z dt = [ωg θ Δ ] and by taking into account the measurable generator speed signal ω g,wehave ż dt = A dt z dt + B 1 τ g + B ω r ω g = C (15) dt z dt, where C dt = [1 ]. Now, the inputs τ g and ω r in (15) are both available, and the pair (A dt, Cdt ) is observable. It is worth noting that the rotor speed sensor fault shows up in (15) as an actuator fault (associated with the input signal ω r ). Then, FDI design in the drive train can be carried out based on (15). The rotor speed sensor fault can be detected by designing a FDE based on (15) or by simply checking the consistency between the two sensor measurements ω r,m1 and ω r,m. Two FIEs are designed based on the following two possible fault scenarios: Case 1: Sensor (i.e., ω r,m ) is faulty, and sensor 1 (i.e., ω r,m1 ) is healthy. Thus, by using (15), we obtain ż dt = A dt z dt + B 1 τ g + B ω r,m1 ω g = C (1) dt z dt. Case : Sensor 1 (i.e., ω r,m1 ) is faulty, and sensor (i.e., ω r,m ) is healthy. Analogously, we have ż dt = A dt z dt + B 1 τ g + B ω r,m ω g = C (17) dt z dt. Then, based on (1) and (17), the two FIEs are chosen as: and ẑ 1 dt = A dt ẑ 1 dt + B 1τ g + B ω r,m1 + L dt (ω g ˆω 1 g ) ˆω 1 g = C dt ẑ 1 dt, ẑ dt = A dt ẑdt + B 1τ g + B ω r,m + L dt (ω g ˆω g ) ˆω g = C dt ẑdt, where ˆω g 1 and ˆω g are the generator speed estimates provided by FIE 1 and FIE, respectively, and L dt is an observer gain designed to make the matrix A dt L dt Cdt stable. Clearly, in the presence of a rotor sensor fault, the output estimation error associated with the matched FIE should converge to zero. Then, by defining ω g 1 = ω g ˆω g 1 and ω g = ω g ˆω g, the following isolation decision scheme is used: If ω g 1 is close to zero, and ω g significantly deviates from zero, then it is concluded that sensor is faulty; If ω g is close to zero, and ω g 1 significantly deviates from zero, then it is concluded that sensor 1 is faulty. 5.3 FDI Method for Generator Speed Sensor Fault The generator speed sensor fault (i.e., fault 5 in the benchmark model) can be detected and isolated using a simple method based on the system dynamics given in Odgaard et al. [9]. Specifically, we have P g = η gc τ g ω g, where P g is the electric power and η gc is the generator efficiency. Since P g, η gc, τ g are all measured or known, an estimate of the generator speed is given by ˆω g = P g, η gc τ g where ˆω g is the estimated generator speed. By comparing ˆω g with the two sensor measurements ω g,m1 and ω g,m1, the generator speed sensor fault can be diagnosed. It is worth noting that the generator speed sensor fault may also affect the residuals ω g 1 and ω g used for FDI of rotor speed sensor. From simulation studies of the benchmark model, it is observed that such effect is very small for the generator speed sensor fault magnitude considered. Nevertheless, even in the presence of a very significant generator speed sensor fault, we can always first apply the FDI method presented here to decide the presence of a generator sensor fault before diagnosing the rotor speed sensor, hence avoiding false alarms.. FDI METHOD FOR CONVERTER SYSTEM In the benchmark model, a converter fault (i.e., fault ) is considered, representing an offset in the internal converter control. The converter dynamics is described by τ g = α gc τ g + α gc τ gr + θα gc τ gr, (1) where α gc = 5, τ g is generator torque, τ gr is the generator torque reference, and θ is a constant offset as a result of the fault (θ = in the absence of the fault). Since τ g is measured, a fault detection estimator can be designed as ˆτ g = λ(ˆτ g τ g ) α gc τ g + α gc τ gr, (19) where ˆτ g is an estimate of τ g,andλ>isafilterpole. Clearly, in the absence of not only faults but also modeling error and noise, the estimation error τ g = τg ˆτ g converges to zero, which can be used for fault detection. Note that among all the faults under consideration, only this fault will affect the residual τ g. Hence, this fault can also be isolated by using τ g. 9
5 Milano (Italy) August - September, SIMULATION RESULTS Next, some FDI simulation results are given to show the effectiveness of the FDI method. A wind speed profile of seconds defined in the benchmark model is used. 7.1 FDI Results in Converter System residual for fault Figure 1 shows the FDI results of an offset in converter torque control (i.e., fault ). The fault occurs between 3 and 39 seconds. As described in Section, the single residual chosen is sufficient to detect and isolate this fault. The top plot in Figure 1 illustrates the behaviors of the residual throughout the simulation run, and the bottom plot gives an enlarged view of the residual in a shorter time interval within which the fault is present. As we can see, due to the presence of sensor noise, the residual is not zero in the absence of the fault. The residual significantly increases after the fault occurs. The fault is detected and isolated in approximately.1 seconds. 7. FDI Results in Drive Train System Figures - 5 describe the FDI results in the drive train system. Specifically, Figure and Figure 3 correspond to the case of a fixed value fault on rotor speed sensor 1 (fault ), which occurs between 15 and 1 seconds. The timebehaviors of the residual throughout the simulation run is shown in Figure, and an enlarged view of the residuals in a shorter time interval within which the fault is present is shown in Figure 3. As can be seen, the fault is timely detected by the detection residual (top plot in each of the two figures). Additionally, the first isolation residual takes significantly large value after fault occurrence, while the second isolation residual remain around zero. Based on the presented isolation decision scheme, we can determine that the fault is on sensor 1. The fault is detected and isolated in approximately.35 seconds. Figure and Figure 5 correspond to the case of a scaling error fault on generator speed sensor (fault 5), which occurs between 1 and 11 seconds. As described in Section 5.3, a simplified FDI method with two residuals is used for diagnosing this fault. The time-behaviors of the residuals throughout the simulation run are shown in Figure, and an enlarged plot is given in Figure 5. As we can see, the FDI results are satisfactory. The fault is detected and isolated in approximately.1 seconds. 7.3 FDI Results in Pitch Systems As described in Section, the FDI method for the three pitch systems are similar. For the sake of space limitations, here only the simulation results of pitch 3 are presented. Two faults in pitch 3 are considered during the simulation run of seconds, including a fixed value fault (i.e., fault 3) on position sensor 1 in the interval of - 7 seconds and an incipient actuator fault (i.e., fault 7) developing gradually in the interval of 3-35 seconds. Figure and Figure 7 are plots for the overall simulation run and an enlarged short time interval, respectively. Both faults are timely detected. The fault detection times for fault 3 an fault 7 are approximately. seconds and residual for fault (englared) Fig. 1. Case of an offset in converter torque control: complete plot (top), enlarged plot (bottom). seconds, respectively. Additionally, when the sensor fault is detected in the interval of - 7 seconds, the isolation residual generated by FIE 1 significantly increases (middle plot), while the other isolation residual generated by FIE always remain around zero (bottom plot), hence allowing the isolation of the fault in sensor 1. It is worth noting that, even though the residual generated by FIE 1 goes to zero after a transient, this is sufficient to exclude the fault case corresponding to FIE 1 based on the isolation decision scheme. Moreover, in the presence of the actuator fault (3-35 seconds), we can see both isolation residuals significantly increase. Therefore, the cases of a fault in sensor 1 or sensor can be excluded, which indicates the occurrence of the third fault type (i.e., actuator fault). The fault isolation times for fault 3 an fault 7 are approximately.5 seconds and 1 seconds, respectively.. CONCLUSIONS In this paper, a FDI method is presented for wind turbines by following the general methodology presented in Zhang et al. [, ]. By utilizing certain structure of system model, the FDE and FIEs are designed without the need of estimating the unknown wind speed and aerodynamic rotor torque. Future research work will include the integration of diagnosis and fault-tolerant control design. REFERENCES M. Blanke, M. Kinnaert, J. Lunze, and M. Staroswiecki. Diagnosis and Fault-Tolerant Control. Springer, Berlin,. C. Dobrila and R. Stefansen. Fault Tolerant Wind Turbine Control. Masters thesis, Technical University of Denmark, Kgl, Lyngby, Denmark, 7. 99
6 Milano (Italy) August - September, 11 1 fault detection residual for rotor speed sensor fault (fault ) 5 detection residual for pitch 3 (faults #3 & #7) residual generated by FIE 1 for fault residual generated by FIE for fault Fig.. Case of a fixed value on rotor speed sensor 1. 1 fault detection residual for rotor speed sensor fault (fault ) isolation residual generated by FIE 1 for pitch 3 (faults #3 & #7) isolation residual generated by FIE for pitch 3 (faults #3 & #7) Fig.. Case of a fixed value fault on position sensor 1 and an actuator fault in pitch residual generated by FIE 1 for fault residual generated by FIE for fault Fig. 3. Enlarged plot for the case of a fixed value on rotor speed sensor 1. residual 1 for fault residual for fault Fig.. Case of a scaling error on generator speed sensor. residual 1 for fault 5 (englared) residual for fault 5 (englared) Fig. 5. Enlarged plot for the case of a scaling error on generator speed sensor. 5 detection residual for pitch 3 (faults #3 & #7) isolation residual generated by FIE 1 for pitch 3 (faults #3 & #7) isolation residual generated by FIE for pitch 3 (faults #3 & #7) Fig. 7. Enlarged plot for the case of a fixed value fault on position sensor 1 and an actuator fault in pitch 3. J. J. Gertler, Fault Detection and Diagnosis in Engineering Systems. Marcel Dekker, New York, NY, 199. Z. Hameeda, Y. Honga, Y. Choa, S. Ahnb, and C. Song, Condition monitoring and fault detection of wind turbines and related algorithms: a review, Renewable and Sustainable Energy Reviews, 13(1):139, January 9. P. F. Odgaard, J. Stoustrup and M. Kinnaert, Fault Tolerant Control of Wind Turbines a benchmark model, Proceedings of IFAC Symp. on Fault Detection, Supervision and Safety for Technical Processes: SAFEPRO- CESS, pp , Barcelona, Spain, 9. P. F. Odgaard and J. Stoustrup, Unknown input observer based scheme for detecting faults in a wind turbine converter, Proceedings of IFAC Symp. on Fault Detection, Supervision and Safety for Technical Processes: SAFEPROCESS, pp. 11-1, Barcelona, Spain, 9. X. Wei, M. Verhaegen, and T. van den Engelen, Sensor fault diagnosis of wind turbines for fault tolerant, Proceedings of the 17th IFAC World Congress, pp. 3 37, Seoul, South Korea,. X. Zhang, M. M. Polycarpou, and T. Parisini, Design and analysis of a fault isolation scheme for a class of uncertain nonlinear systems, IFAC Annual Reviews in Control, vol. 3, pp ,. X. Zhang, M. M. Polycarpou, and T. Parisini, A robust detection and isolation scheme for abrupt and incipient faults in nonlinear systems, IEEE Trans. on Automatic Control, vol. 7, pp ,. 3
Unknown Input Observer Based Detection of Sensor Faults in a Wind Turbine
Unknown Input Observer Based Detection of Sensor Faults in a Wind Turbine Peter F Odgaard, Member, IEEE and Jakob Stoustrup, Senior Member IEEE Abstract in this paper an unknown input observer is designed
More informationUnknown input observer based scheme for detecting faults in a wind turbine converter Odgaard, Peter Fogh; Stoustrup, Jakob
Aalborg Universitet Unknown input observer based scheme for detecting faults in a wind turbine converter Odgaard, Peter Fogh; Stoustrup, Jakob Published in: Elsevier IFAC Publications / IFAC Proceedings
More informationFault Tolerant Control of Wind Turbines using Unknown Input Observers
Fault Tolerant Control of Wind Turbines using Unknown Input Observers Peter Fogh Odgaard Jakob Stoustrup kk-electronic a/s, 7430 Ikast, Denmark (Tel: +45 21744963; e-mail: peodg@kk-electronic.com). Aalborg
More informationFault detection of a benchmark wind turbine using interval analysis
212 American Control Conference Fairmont Queen Elizabeth, Montréal, Canada June 27-June 29, 212 Fault detection of a benchmark wind turbine using interval analysis Seyed Mojtaba Tabatabaeipour and Peter
More informationWind Turbine Fault Detection Using Counter-Based Residual Thresholding
Wind Turbine Fault Detection Using Counter-Based Residual Thresholding Ahmet Arda Ozdemir, Peter Seiler, and Gary J. Balas Department of Aerospace Engineering and Mechanics, University of Minnesota, Minneapolis,
More informationFault Detection and Isolation for a Wind Turbine Benchmark using a mixed Bayesian/Set-membership Approach
Fault Detection and Isolation for a Wind Turbine Benchmark using a mixed Bayesian/Set-membership Approach Rosa M. Fernandez-Canti a, Joaquim Blesa a,b, Sebastian Tornil-Sin a, Vicenç Puig a,b, a Research
More informationAFAULT diagnosis procedure is typically divided into three
576 IEEE TRANSACTIONS ON AUTOMATIC CONTROL, VOL. 47, NO. 4, APRIL 2002 A Robust Detection and Isolation Scheme for Abrupt and Incipient Faults in Nonlinear Systems Xiaodong Zhang, Marios M. Polycarpou,
More informationFDI and FTC of Wind Turbines using the Interval Observer Approach and Virtual Actuators/Sensors
FDI and FTC of Wind Turbines using the Interval Observer Approach and Virtual Actuators/Sensors Joaquim Blesa a,b, Damiano Rotondo a, Vicenç Puig a,b, Fatiha Nejjari a a Automatic Control Department, Universitat
More informationKarhunen Loeve basis used for Detection of Gearbox Faults in a Wind Turbine
Preprints of the 19th World Congress The International Federation of Automatic Control Cape Town, South Africa. August 24-29, 214 Karhunen Loeve basis used for Detection of Gearbox Faults in a Wind Turbine
More informationFault Detection of Wind Turbines with Uncertain Parameters Tabatabaeipour, Seyed Mojtaba; Odgaard, Peter Fogh; Bak, Thomas; Stoustrup, Jakob
Aalborg Universitet Fault Detection of Wind Turbines with Uncertain Parameters Tabatabaeipour, Seyed Mojtaba; Odgaard, Peter Fogh; Bak, Thomas; Stoustrup, Jakob Published in: Energies DOI (link to publication
More informationIntelligent Fault Diagnosis Techniques Applied to an Offshore Wind Turbine System **
Article Intelligent Fault Diagnosis Techniques Applied to an Offshore Wind Turbine System ** Silvio Simani 1, Paolo Castaldi 2 1 Dipartimento di Ingegneria, Università degli Studi di Ferrara. Via Saragat
More informationMODEL-BASED fault detection and isolation
Robust Fault Diagnosis of Non-linear Systems using Interval Constraint Satisfaction and Analytical Redundancy Relations Sebastian Tornil-Sin, Carlos Ocampo-Martinez, Vicenç Puig and Teresa Escobet Abstract
More informationModel Based Fault Detection and Diagnosis Using Structured Residual Approach in a Multi-Input Multi-Output System
SERBIAN JOURNAL OF ELECTRICAL ENGINEERING Vol. 4, No. 2, November 2007, 133-145 Model Based Fault Detection and Diagnosis Using Structured Residual Approach in a Multi-Input Multi-Output System A. Asokan
More informationCombination of Model-based Observer and Support Vector Machines for Fault Detection of Wind Turbines
International Journal of Automation and Computing 11(3), June 2014, 274-287 DOI: 10.1007/s11633-014-0790-9 Combination of Model-based Observer and Support Vector Machines for Fault Detection of Wind Turbines
More informationINTEGRATED ARCHITECTURE OF ACTUATOR FAULT DIAGNOSIS AND ACCOMMODATION
INTEGRATED ARCHITECTURE OF ACTUATOR FAULT DIAGNOSIS AND ACCOMMODATION Rim Hamdaoui, Safa Guesmi, Rafika Elharabi and Med Naceur Abdelkrim UR. Modelling, Analysis and Systems Control, University of Gabes,
More informationActuator Fault Tolerant PID Controllers
Actuator Fault Tolerant PID Controllers César Castro Rendón Cristina Verde Alejandro Mora Hernández Instituto de Ingeniería-Universidad Nacional Autónoma de México Coyoacán DF, 04510, México cesarcasren@yahoo.com.mx
More informationA ROBUST ITERATIVE LEARNING OBSERVER BASED FAULT DIAGNOSIS OF TIME DELAY NONLINEAR SYSTEMS
Copyright IFAC 15th Triennial World Congress, Barcelona, Spain A ROBUST ITERATIVE LEARNING OBSERVER BASED FAULT DIAGNOSIS OF TIME DELAY NONLINEAR SYSTEMS Wen Chen, Mehrdad Saif 1 School of Engineering
More informationIdentification of a Chemical Process for Fault Detection Application
Identification of a Chemical Process for Fault Detection Application Silvio Simani Abstract The paper presents the application results concerning the fault detection of a dynamic process using linear system
More informationSimultaneous State and Fault Estimation for Descriptor Systems using an Augmented PD Observer
Preprints of the 19th World Congress The International Federation of Automatic Control Simultaneous State and Fault Estimation for Descriptor Systems using an Augmented PD Observer Fengming Shi*, Ron J.
More informationVariable structure strategy to avoid torque control saturation of a wind turbine in the presence of faults
International Conference on Renewable Energies and Power Quality (ICREPQ 16) Madrid (Spain), 4 th to 6 th May, 216 Renewable Energy and Power Quality Journal (RE&PQJ) ISSN 2172-38 X, No.14 May 216 Variable
More informationApplication of Adaptive Thresholds in Robust Fault Detection of an Electro- Mechanical Single-Wheel Steering Actuator
Preprints of the 8th IFAC Symposium on Fault Detection, Supervision and Safety of Technical Processes (SAFEPROCESS) August 29-31, 212. Mexico City, Mexico Application of Adaptive Thresholds in Robust Fault
More informationFault Detection and Isolation in DFIG Driven by a Wind Turbine with a Variable Rotor Resistance
Sustainability in Energy and Buildings: Research Advances http://nimbusvault.net/publications/koala/sebra Special Edition - Mediterranean Green Energy Forum 23 (MGEF-3) : Vol.2 : pp.3-22 : mgf3s-4 Fault
More informationSuper-twisting controllers for wind turbines
International Conference on Renewable Energies and Power Quality (ICREPQ 16) Madrid (Spain), 4 th to 6 th May, 16 Renewable Energy and Power Quality Journal (RE&PQJ) ISSN 17-38 X, No.14 May 16 Super-twisting
More informationISSN Article
Energies 215, 8, 43-4316; doi:1.339/en8543 OPEN ACCESS energies ISSN 1996-173 www.mdpi.com/journal/energies Article Fault Diagnosis and Fault-Tolerant Control of Wind Turbines via a Discrete Time Controller
More informationAFRL-PR-WP-TP
AFRL-PR-WP-TP-2006-275 SENSOR VALIDATION USING NONLINEAR MINOR COMPONENT ANALYSIS (PREPRINT) Roger Xu, Guangfan Zhang, Xiaodong Zhang, Leonard Haynes, Chiman Kwan, and Kenneth Semega MAY 2006 Approved
More informationRobust Fault Tolerant Control Framework using Uncertain. Takagi-Sugeno Fuzzy Models
Robust Fault Tolerant Control Framework using Uncertain Takagi-Sugeno Fuzzy Models Damiano Rotondo, Fatiha Nejjari and Vicenç Puig Abstract This chapter is concerned with the introduction of a fault tolerant
More informationTHE development of wind energy conversion systems
IEEE TRANSACTIONS ON CONTROL SYSTEMS TECHNOLOGY, VOL. 23, NO. 1, JANUARY 2015 245 A Set-Valued Approach to FDI and FTC of Wind Turbines Pedro Casau, Paulo Rosa, Seyed Mojtaba Tabatabaeipour, Carlos Silvestre,
More informationFault Detection and Diagnosis for a Three-tank system using Structured Residual Approach
Fault Detection and Diagnosis for a Three-tank system using Structured Residual Approach A.Asokan and D.Sivakumar Department of Instrumentation Engineering, Faculty of Engineering & Technology Annamalai
More informationA Unified Nonlinear Adaptive Approach for the Fault Diagnosis of Aircraft Engines
Wright State University CORE Scholar Browse all Theses and Dissertations Theses and Dissertations 212 A Unified Nonlinear Adaptive Approach for the Fault Diagnosis of Aircraft Engines Remus C. Avram Wright
More informationStructured LPV Control of Wind Turbines
fda@es.aau.dk Department of Electronic Systems, November 29, 211 Agenda Motivation Main challenges for the application of wind turbine control: Known parameter-dependencies (gain-scheduling); Unknown parameter
More informationSTRUCTURAL DESIGN OF SYSTEMS WITH SAFE BEHAVIOR UNDER SINGLE AND MULTIPLE FAULTS. and Marcel Staroswiecki
STRUCTURAL DESIGN OF SYSTEMS WITH SAFE BEHAVIOR UNDER SINGLE AND MULTIPLE FAULTS Mogens Blanke and Marcel Staroswiecki Automation at Ørsted DTU, Build. 326, Technical University of Denmark, Kgs. Lyngby,
More informationRobust Actuator Fault Detection and Isolation in a Multi-Area Interconnected Power System
Proceedings of the World Congress on Engineering 2011 Vol II, July 6-8, 2011, London, U.K. Robust Actuator Fault Detection and Isolation in a Multi-Area Interconnected Power System Istemihan Genc, and
More informationA Multiple-Observer Scheme for Fault Detection, Isolation and Recovery of Satellite Thrusters
Proceedings of the EuroGNC 3, nd CEAS Specialist Conference on Guidance, Navigation & Control, Delft University of Technology, Delft, The Netherlands, April -, 3 FrBT.3 A Multiple-Observer Scheme for Fault
More informationDistributed Fault Diagnosis using Sensor Networks and Consensus-based Filters
Proceedings of the 45th IEEE Conference on Decision & Control Manchester Grand Hyatt Hotel San Diego, CA, USA, December 3-5, 26 WeA.4 Distributed Fault Diagnosis using Sensor Networks and Consensus-based
More informationCautious Data Driven Fault Detection and Isolation applied to the Wind Turbine Benchmark
Driven Fault Detection and Isolation applied to the Wind Turbine Benchmark Prof. Michel Verhaegen Delft Center for Systems and Control Delft University of Technology the Netherlands November 28, 2011 Prof.
More informationFAULT DETECTION OF A CONTROL VALVE USING STRUCTURED PARITY EQUATIONS
FAULT DETECTION OF A CONTROL VALVE USING STRUCTURED PARITY EQUATIONS Felipe Nunes Radtke, Fernando Lizarralde Dept. of Electrical Eng., COPPE, Federal University of Rio de Janeiro Rio de Janeiro, RJ, Brazil
More informationA Bayesian Approach to Efficient Diagnosis of Incipient Faults
A Bayesian Approach to Efficient Diagnosis of Incipient Faults Indranil Roychoudhury, Gautam Biswas and Xenofon Koutsoukos Institute for Software Integrated Systems (ISIS) Department of Electrical Engineering
More informationNeural Networks Lecture 10: Fault Detection and Isolation (FDI) Using Neural Networks
Neural Networks Lecture 10: Fault Detection and Isolation (FDI) Using Neural Networks H.A. Talebi Farzaneh Abdollahi Department of Electrical Engineering Amirkabir University of Technology Winter 2011.
More informationONGOING WORK ON FAULT DETECTION AND ISOLATION FOR FLIGHT CONTROL APPLICATIONS
ONGOING WORK ON FAULT DETECTION AND ISOLATION FOR FLIGHT CONTROL APPLICATIONS Jason M. Upchurch Old Dominion University Systems Research Laboratory M.S. Thesis Advisor: Dr. Oscar González Abstract Modern
More informationAdaptive Control of Variable-Speed Variable-Pitch Wind Turbines Using RBF Neural Network
Schulich School of Engineering Department of Mechanical and Manufacturing Engineering Adaptive Control of Variable-Speed Variable-Pitch Wind Turbines Using RBF Neural Network By: Hamidreza Jafarnejadsani,
More informationActuator Fault-Tolerant Control based on Invariant Set Separation
Proceedings of the 7th World Congress The International Federation of Automatic Control Seoul, Korea, July 6-, 28 Actuator Fault-Tolerant Control based on Invariant Set Separation Carlos Ocampo-Martínez
More informationErik Frisk and Lars Nielsen
ROBUST RESIDUAL GENERATION FOR DIAGNOSIS INCLUDING A REFERENCE MODEL FOR RESIDUAL BEHAVIOR Erik Frisk and Lars Nielsen Dept. of Electrical Engineering, Linköping University Linköping, Sweden Email: frisk@isy.liu.se,
More informationAn Architecture for Fault Tolerant Controllers
An Architecture for Fault Tolerant Controllers Henrik Niemann Ørsted DTU, Automation Technical University of Denmark Building 326, DK2800 Lyngby, Denmark Email: hhn@oersted.dtu.dk www.oersted.dtu.dk/staff/all/hhn/
More informationFAULT DETECTION for SPACECRAFT ATTITUDE CONTROL SYSTEM. M. Amin Vahid D. Mechanical Engineering Department Concordia University December 19 th, 2010
FAULT DETECTION for SPACECRAFT ATTITUDE CONTROL SYSTEM M. Amin Vahid D. Mechanical Engineering Department Concordia University December 19 th, 2010 Attitude control : the exercise of control over the orientation
More informationFAULT DETECTION AND FAULT TOLERANT APPROACHES WITH AIRCRAFT APPLICATION. Andrés Marcos
FAULT DETECTION AND FAULT TOLERANT APPROACHES WITH AIRCRAFT APPLICATION 2003 Louisiana Workshop on System Safety Andrés Marcos Dept. Aerospace Engineering and Mechanics, University of Minnesota 28 Feb,
More informationChange Detection with prescribed false alarm and detection probabilities. Mogens Blanke
CeSOS Workshop NTNU May 27-29 2013 Change Detection with prescribed false alarm and detection probabilities Mogens Blanke Adjunct Professor at Centre for Ships and Ocean Structures, NTNU, Norway Professor
More informationHybrid automaton incremental construction for online diagnosis
Hybrid automaton incremental construction for online diagnosis Jorge Vento, Louise Travé-Massuyès 2,3, Ramon Sarrate and Vicenç Puig Advanced Control Systems (SAC), Universitat Politècnica de Catalunya
More informationROBUST REDUNDANCY RELATIONS FOR FAULT DIAGNOSIS IN NONLINEAR DESCRIPTOR SYSTEMS
Proceedings of te IASTED International Conference Modelling Identification and Control (AsiaMIC 23) April - 2 23 Puket Tailand ROBUST REDUNDANCY RELATIONS FOR FAULT DIAGNOSIS IN NONLINEAR DESCRIPTOR SYSTEMS
More informationFault-Tolerant Switching Scheme with Multiple Sensor-Controller Pairs
Proceedings of the 17th World Congress The International Federation of Automatic Control Seoul, Korea, July 6-11, 8 Fault-Tolerant Switching Scheme with Multiple Sensor-Controller Pairs John J. Martínez,1
More informationSecond Order Step by Step Sliding mode Observer for Fault Estimation in a Class of Nonlinear Fractional Order Systems
Second Order Step by Step Sliding mode Observer for Fault Estimation in a Class of Nonlinear Fractional Order Systems Seyed Mohammad Moein Mousavi Student Electrical and Computer Engineering Department
More informationGain-scheduled Linear Quadratic Control of Wind Turbines Operating at High Wind Speed
16th IEEE International Conference on Control Applications Part of IEEE Multi-conference on Systems and Control Singapore, 1-3 October 7 Gain-scheduled Linear Quadratic Control of Wind Turbines Operating
More informationRobust Control For Variable-Speed Two-Bladed Horizontal-Axis Wind Turbines Via ChatteringControl
Robust Control For Variable-Speed Two-Bladed Horizontal-Axis Wind Turbines Via ChatteringControl Leonardo Acho, Yolanda Vidal, Francesc Pozo CoDAlab, Escola Universitària d'enginyeria Tècnica Industrial
More informationAn Efficient Algorithm for Finding Over-constrained Sub-systems for Construction of Diagnostic Tests
An Efficient Algorithm for Finding Over-constrained Sub-systems for Construction of Diagnostic Tests Mattias Krysander, Jan Åslund, Mattias Nyberg Linköpings universitet, Dept. of Electrical Engineering
More informationOnboard Engine FDI in Autonomous Aircraft Using Stochastic Nonlinear Modelling of Flight Signal Dependencies
Onboard Engine FDI in Autonomous Aircraft Using Stochastic Nonlinear Modelling of Flight Signal Dependencies Dimitrios G. Dimogianopoulos, John D. Hios and Spilios D. Fassois Stochastic Mechanical Systems
More informationAn Actuator Failure Tolerant Robust Control Approach for an Underwater Remotely Operated Vehicle
5th IEEE Conference on Decision and Control and European Control Conference (CDC-ECC) Orlando, FL, USA, December -5, An Actuator Failure Tolerant Robust Control Approach for an Underwater Remotely Operated
More informationFAULT DETECTION AND ISOLATION FOR ROBOT MANIPULATORS USING ANFIS AND WAVELET
FAULT DETECTION AND ISOLATION FOR ROBOT MANIPULATORS USING ANFIS AND WAVELET Tolga YÜKSEL, Abdullah SEZGİN, Department of Electrical and Electronics Engineering Ondokuz Mayıs University Kurupelit Campus-Samsun
More informationAalborg Universitet. Publication date: Document Version Også kaldet Forlagets PDF. Link to publication from Aalborg University
Aalborg Universitet Model Based Fault Diagnosis in a Centrifugal Pump Application using Structural Analysis Kallesøe, C. S.; Izadi-Zamanabadi, Roozbeh; Rasmussen, Henrik; Cocquempot, V. Publication date:
More informationA nonlinear fault-tolerant thruster allocation architecture for underwater remotely operated vehicles
Preprints, th IFAC Conference on Control Applications in Marine Systems September 3-6, 26. Trondheim, Norway A nonlinear fault-tolerant thruster allocation architecture for underwater remotely operated
More informationNorm invariant discretization for sampled-data fault detection
Automatica 41 (25 1633 1637 www.elsevier.com/locate/automatica Technical communique Norm invariant discretization for sampled-data fault detection Iman Izadi, Tongwen Chen, Qing Zhao Department of Electrical
More informationRobust Fault Diagnosis of Uncertain One-dimensional Wave Equations
Robust Fault Diagnosis of Uncertain One-dimensional Wave Equations Satadru Dey 1 and Scott J. Moura Abstract Unlike its Ordinary Differential Equation ODE counterpart, fault diagnosis of Partial Differential
More informationA COMPARISON OF TWO METHODS FOR STOCHASTIC FAULT DETECTION: THE PARITY SPACE APPROACH AND PRINCIPAL COMPONENTS ANALYSIS
A COMPARISON OF TWO METHODS FOR STOCHASTIC FAULT DETECTION: THE PARITY SPACE APPROACH AND PRINCIPAL COMPONENTS ANALYSIS Anna Hagenblad, Fredrik Gustafsson, Inger Klein Department of Electrical Engineering,
More informationActive fault-tolerant control design for Takagi-Sugeno fuzzy systems
BULLETIN OF THE POLISH ACADEMY OF SCIENCES TECHNICAL SCIENCES Vol. 59 No. 1 2011 DOI: 10.2478/v10175-011-0013-2 Varia Active fault-tolerant control design for Takagi-Sugeno fuzzy systems Ł. DZIEKAN M.
More informationA time-delayed observer for fault detection and isolation in
Robotica (6) volume 4, pp. 557 565. 6 Cambridge University Press doi:.7/s635747564 Printed in the United Kingdom A time-delayed observer for fault detection and isolation in industrial robots F. Caccavale,
More informationNonlinear Control of Variable Speed Wind Turbines without wind speed measurement
Proceedings of the 44th IEEE Conference on Decision and Control, and the European Control Conference 5 Seville, Spain, December 12-15, 5 TuIB21.4 Nonlinear Control of Variable Speed Wind Turbines without
More informationEvaluation of Observer Structures with Application to Fault Detection
Evaluation of Observer Structures with Application to Fault Detection A Thesis Presented by Ju Zhang to The Department of Electrical and Computer Engineering in Partial Fulfillment of the Requirements
More informationSensor Placement for Fault Diagnosis Based On Causal Computations
Preprints of the 7th IFAC Symposium on Fault Detection, Supervision and Safety of Technical Processes Barcelona, Spain, June 30 - July 3, 2009 Sensor Placement for Fault Diagnosis Based On Causal Computations
More informationRECONFIGURABILITY ANALYSIS FOR RELIABLE FAULT TOLERANT CONTROL DESIGN
Int. J. Appl. Math. Comput. Sci., 2, Vol. 2, No. 3, 43 439 DOI:.2478/v6--32-z RECONFIGURABILITY ANALYSIS FOR RELIABLE FAULT TOLERANT CONTROL DESIGN AHMED KHELASSI, DIDIER THEILLIOL, PHILIPPE WEBER Research
More informationDistributed fault-tolerant strategy for networked robots with both cooperative and reactive controls
Distributed fault-tolerant strategy for networked robots with both cooperative and reactive controls Filippo Arrichiello, Alessandro Marino, Francesco Pierri Abstract The paper presents a controller-observer
More informationData Driven Fault Detection and Isolation of a Wind Turbine Benchmark
Data Driven Fault Detection and Isolation of a Wind Turbine Benchmark Jianfei Dong Michel Verhaegen Delft University of Technology, 2628CD, Delft, the Netherlands Email: jdong@tudelftnl, MVerhaegen@moesporg
More informationLinear Model Based Diagnostic Framework of Three Tank System
Proceedings of the th WEA International Conference on YTEM, Agios Nikolaos, Crete Island, Greece, July -5, 7 7 Linear Model Based Diagnostic Framework of Three Tank ystem M. Iqbal Department of Computer
More informationIndividual pitch control of wind turbines using local inflow measurements
Proceedings of the 17th World Congress The International Federation of Automatic Control pitch control of wind turbines using local inflow measurements S. C. Thomsen H. Niemann N. K. Poulsen Department
More informationResearch Article Robust Fault Diagnosis Design for Linear Multiagent Systems with Incipient Faults
Mathematical Problems in Engineering Volume 215, Article ID 436935, 7 pages http://dx.doi.org/1.1155/215/436935 Research Article Robust Fault Diagnosis Design for Linear Multiagent Systems with Incipient
More informationRobustness analysis of sensor placement for leak detection and location under uncertain operating conditions
Robustness analysis of sensor placement for leak detection and location under uncertain operating conditions Joaquim Blesa a, Fatiha Nejjari b, Ramon Sarrate b a Institut de Robòtica i Informàtica Industrial
More informationLINEAR OPTIMIZATION OF PARAMETERS IN DYNAMIC THRESHOLD GENERATORS
LINEAR OPTIMIZATION OF PARAMETERS IN DYNAMIC THRESHOLD GENERATORS Michael Bask, Andreas Johansson Control Engineering Group Luleå University of Technology SE-971 87 Luleå, Sweden Email: Michael.Bask@csee.ltu.se
More informationEngineering Tripos Part IB. Part IB Paper 8: - ELECTIVE (2)
Engineering Tripos Part IB SECOND YEAR Part IB Paper 8: - ELECTIVE (2) MECHANICAL ENGINEERING FOR RENEWABLE ENERGY SYSTEMS Examples Paper 2 Wind Turbines, Materials, and Dynamics All questions are of Tripos
More informationWind Turbine Control
Wind Turbine Control W. E. Leithead University of Strathclyde, Glasgow Supergen Student Workshop 1 Outline 1. Introduction 2. Control Basics 3. General Control Objectives 4. Constant Speed Pitch Regulated
More informationReconfigurable Fault Tolerant Control Using GIMC Structure
Reconfigurable Fault Tolerant Control Using GIMC Structure Daniel U. Campos Delgado College of Sciences UASLP Mexico ducd@galia.fc.uaslp.mx Kemin Zhou Dept. of Elec. & Comp. Eng. Louisiana State University
More informationFault Diagnosis of Interconnected Cyber-Physical Systems
Fault Diagnosis of Interconnected Cyber-Physical Systems Marios M. Polycarpou Professor, IEEE Fellow, IFAC Fellow Director, KIOS Research and Innovation Center of Excellence Dept. Electrical and Computer
More informationActuator fault diagnosis and fault-tolerant control: Application to the quadruple-tank process
Journal of Physics: Conference Series OPEN ACCESS Actuator fault diagnosis and fault-tolerant control: Application to the quadruple-tank process To cite this article: Mariusz Buciakowski et al 1 J. Phys.:
More informationFAULT diagnosis is crucial for ensuring the safe operation
A Qualitative Event-based Approach to Continuous Systems Diagnosis Matthew J. Daigle Member, IEEE, Xenofon D. Koutsoukos Senior Member, IEEE, and Gautam Biswas Senior Member, IEEE Abstract Fault diagnosis
More informationAnomaly detection of a horizontal wind turbine using an Extended Kalman Filter
. Title Anomaly detection of a horizontal wind turbine using an Extended Kalman Filter 1. Introduction Loads that have a disproportionate impact on the components and structure of a wind turbine can be
More informationNonlinear FDI based on state derivatives, as provided by inertial measurement units
Preprints of the 8th IFAC Symposium on Nonlinear Control Systems ThP02.4 University of Bologna, Italy, September 1-3, 2010 Nonlinear FDI based on state derivatives, as provided by inertial measurement
More informationKarhunen-Loéve (PCA) based detection of multiple oscillations in multiple measurement signals from large-scale process plants
Karhunen-Loéve (PCA) based detection of multiple oscillations in multiple measurement signals from large-scale process plants P. F. Odgaard and M. V. Wickerhauser Abstract In the perspective of optimizing
More informationHW VS SW SENSOR REDUNDANCY: FAULT DETECTION AND ISOLATION OBSERVER BASED APPROACHES FOR INERTIAL MEASUREMENT UNITS
HW VS SW SENSOR REDUNDANCY: FAULT DETECTION AND ISOLATION OBSERVER BASED APPROACHES FOR INERTIAL MEASUREMENT UNITS Abstract Immacolata Notaro*, Marco Ariola**, Egidio D Amato*, Massimiliano Mattei* *Dipartimento
More informationDIAGNOSIS OF DISCRETE-TIME SINGULARLY PERTURBED SYSTEMS BASED ON SLOW SUBSYSTEM
acta mechanica et automatica, vol.8 no.4 (4), DOI.478/ama-4-3 DIAGNOSIS OF DISCRETE-TIME SINGULARLY PERTURBED SYSTEMS BASED ON SLOW SUBSYSTEM Adel TELLILI *,***, Nouceyba ABDELKRIM *,**, Bahaa JAOUADI
More informationWind turbine modeling by friction effects
Proceedings of the 7th World Congress The International Federation of Automatic Control Seoul, Korea, July 6-, 8 Wind turbine modeling by friction effects Juvenal Villanueva Luis Alvarez-Icaza Instituto
More informationWhy fault tolerant system?
Why fault tolerant system? Non Fault-Tolerant System Component 1 Component 2 Component N The reliability block diagram of a series systemeach element of the system must operate correctly for the system
More informationA COMBINED QUALITATIVE/QUANTITATIVE APPROACH FOR FAULT ISOLATION IN CONTINUOUS DYNAMIC SYSTEMS
A COMBINED QUALITATIVE/QUANTITATIVE APPROACH FOR FAULT ISOLATION IN CONTINUOUS DYNAMIC SYSTEMS EricJ. Manders Sriram Narasimhan Gautam Biswas Pieter J. Mosterman Department of Electrical Engineering and
More informationUncertainty Quantification for Robust Control of Wind Turbines using Sliding Mode Observer
Journal of Physics: Conference Series PAPER OPEN ACCESS Uncertainty Quantification for Robust Control of Wind Turbines using Sliding Mode Observer To cite this article: Horst Schulte 16 J Phys: Conf Ser
More informationIntegrating Reliability into the Design of Power Electronics Systems
Integrating Reliability into the Design of Power Electronics Systems Alejandro D. Domínguez-García Grainger Center for Electric Machinery and Electromechanics Department of Electrical and Computer Engineering
More informationFault-Tolerant Control Strategies for a Class of Euler-Lagrange Nonlinear Systems Subject to Simultaneous Sensor and Actuator Faults
Fault-Tolerant Control Strategies for a Class of Euler-Lagrange Nonlinear Systems Subject to Simultaneous Sensor and Actuator Faults Maryam Abdollahi A Thesis in The Department of Electrical and Computer
More informationHIGHER-ORDER SLIDING MODE TECHNIQUES FOR FAULT DIAGNOSIS
Ph.D. in Electronic and Computer Engineering Dept. of Electrical and Electronic Engineering University of Cagliari HIGHER-ORDER SLIDING MODE TECHNIQUES FOR FAULT DIAGNOSIS Nicola Orani Advisor: Elio Usai
More informationCharacterization of the Minimum Detectable Fault of Interval Observers by using Set-invariance Theory
Characterization of the Minimum Detectable Fault of Interval Observers by using Set-invariance Theory Masoud Pourasghar 1,2, Vicenç Puig 1,2 and Carlos Ocampo-Martinez 1,2 Abstract This paper addresses
More informationRobust model based control method for wind energy production
Robust model based control method for wind energy production Andreea Pintea, Dumitru Popescu, Ioana Pisica To cite this version: Andreea Pintea, Dumitru Popescu, Ioana Pisica. Robust model based control
More informationMultilevel Analysis of Continuous AE from Helicopter Gearbox
Multilevel Analysis of Continuous AE from Helicopter Gearbox Milan CHLADA*, Zdenek PREVOROVSKY, Jan HERMANEK, Josef KROFTA Impact and Waves in Solids, Institute of Thermomechanics AS CR, v. v. i.; Prague,
More informationWind Turbine Model and Observer in Takagi- Sugeno Model Structure
Journal of Physics: Conference Series OPEN ACCESS Wind Turbine Model and Observer in Takagi- Sugeno Model Structure To cite this article: Sören Georg et al 214 J. Phys.: Conf. Ser. 555 1242 View the article
More informationTECHNICAL systems are invariably subject to faults. In
1590 IEEE TRANSACTIONS ON AUTOMATIC CONTROL, VOL. 51, NO. 10, OCTOBER 2006 Control Reconfiguration After Actuator Failures Using Disturbance Decoupling Methods Jan Lunze, Member, IEEE, and Thomas Steffen
More informationA Particle-Filtering Based Approach for Distributed Fault Diagnosis of Large-Scale Interconnected Nonlinear Systems
A Particle-Filtering Based Approach for Distributed Fault Diagnosis of Large-Scale Interconnected Nonlinear Systems Elaheh Noursadeghi, Ioannis Raptis Mechanical Engineering Department, University of Massachusetts
More informationA SYSTEMATIC INCLUSION OF DIAGNOSIS PERFORMANCE IN FAULT TREE ANALYSIS
SYSTEMTIC INCLUSION OF DIGNOSIS PERFORMNCE IN FULT TREE NLYSIS Jan Åslund, Jonas Biteus, Erik Frisk, Mattias Kryser, Lars Nielsen Department of Electrical Engineering, Linköpings universitet, 58 83 Linköping,
More informationAn Improved Nonlinear Speed Controller for Series DC Motors
Proceedings of the 17th World Congress The International Federation of Automatic Control Seoul, Korea, July 6-11, 8 An Improved Nonlinear Speed Controller for Series DC Motors Dongbo Zhao Ning Zhang Department
More information