Thermo-Structural Analysis of Thermal Protection System for Re-Entry Module of Human Space Flight
|
|
- Richard Chapman
- 5 years ago
- Views:
Transcription
1 Thermo-Structural Analysis of Thermal Protection System for Re-Entry Module of Human Space Flight Manu. Jˡ, G. Vinod 2, Dr. Roy N Mathews 3 Abstract Advanced Space Transportation systems involve the reusable vehicles or modules which can be recovered from orbits of Earth or outer planets. The major challenge in the development of such modules is the design of the thermal protection system (TPS) which should withstand the high aerodynamic heating levels encountered during the atmospheric re-entry. The objective of the study was to conduct a thermo-structural analysis of the TPS of a re-entry module called Crew module developed by Indian Space Research Organisation (ISRO). Thermo-structural analysis consists of heat transfer analysis to obtain temperature distribution with its variation for the entire duration of the operation. It is followed by structural analysis for thermal and mechanical load to obtain structural deformations and stresses. Index Terms Aerodynamic heating, Re-entry vehicle, Thermal protection system, Thermo-structural analysis. I INTRODUCTION The development of atmospheric re-entry vehicles began in the late 1950's. Atmospheric re-entry refers to the movement of human made objects as they enter the atmosphere of a planet from outer space. The major challenge in the development of re-entry vehicle is the design of Thermal Protection System (TPS) which should withstand the high aerodynamic heating levels encountered during the atmospheric re-entry. Aerodynamic heating refers to the heating of a body produced by the passage of air or other gases over its surface. It is caused by friction and compression process and significant chiefly at high speeds. Due to aerodynamic heating external surfaces of the re-entry vehicle gets heated. Thermal Protection Systems are necessary in order to protect the internal structure of the vehicle from the elevated heat fluxes occurring on the external surfaces. The design of a Thermal Protection System is based on the principle that the energy released by the aerodynamic heating must be absorbed or rejected by the Thermal Protection System. Crew Module Atmospheric Re-entry Experiment (CARE) is an experimental test vehicle for the Indian Space Research Organisations future orbital vehicle. The TPS of crew module is made up of carbon-phenolic tiles. Schematic sketch of TPS for crew module is shown in Figure 1.1. The forward heat shield will be the leading edge during the re-entry; hence it will be subjected to maximum heat flux. Manu J PG Scholar, Department of Mechanical Engg, Mar Athanasius College of Engineering, Kothamangalam Figure 1.1: TPS of crew module Finite element model of the TPS was designed using ANSYS WORKBENCH. Transient thermal analysis has been carried out up to 200s. The temperature distribution corresponding 100s (which is the maximum heat flux condition), 180s (which is the maximum temperature condition) and 200s are obtained for thermo-structural analysis. Thermo-structural analysis has been carried out at all the above mentioned time instants by applying temperature and pressure as loads. II FINITE ELEMENT MODEL Three dimensional CAD geometry was generated and imported to the finite element software. Finite element modelling is done in ANSYS WORKBENCH. Hexahedral type of meshing is used for the forward heat shield, flare and conical heat shield which contains numbers of nodes and numbers of elements. Tetrahedral type of meshing is used for the inner metallic structure which contains numbers of nodes and numbers of elements Figure 2.1: Finite element model of forward heat shield and flare region ISSN: All Rights Reserved 2016 IJSETR 125
2 experienced by the TPS during re-entry. Heat flux at any point on outer surface of TPS follows a parabolic curve with respect to time, being zero at the start and attaining a maximum at time 100sec. Figure 2.2: Finite element model of conical heat shield 3.1 Material Properties The material properties required for the thermal analysis are thermal conductivity, specific heat and density. Carbon-phenolic tiles used for TPS are orthotropic in nature and the material properties are temperature dependent. Table 3.1: Variation of thermal conductivity with temperature Temperature(T) Thermal Conductivity [K] [W/mK] X-dierction Y-dierction Z-dierction Figure 2.3: Finite element model of inner metallic backup structure Fig. 2.1 shows the finite element model of forward heat shield and flare region, Fig. 2.2 shows the finite element model of conical heat shield and Fig. 2.3 shows the finite element model of inner metallic backup structure III TRANSIENT THERMAL ANALYSIS Transient thermal analysis determines temperatures and other thermal quantities that vary over time. Engineers commonly use temperatures that a transient thermal analysis calculates as input to structural analysis for thermal stress evaluations. A transient thermal analysis follows basically the same procedures as a steady state thermal analysis. The main difference is that most applied loads in a transient thermal analysis are functions of time. The transient temperature distribution T (x; y; z; t) throughout the domain is obtained by solving the three-dimensional heat conduction equation shown below in the substrate along with appropriate initial and boundary conditions. ρc p( T/ t) = / x (k x T/ x) + / y (k y T/ y) + / z(k z T/ z) (1) Where ρ Density. C p Specific Heat. k x, k y, k z Thermal Conductivities in x, y, z directions. All material properties are considered temperature dependent. Initial conditions applied to solve Eq.(1) is T (x; y; z; 0) = T 0 (2) Where T 0 is the ambient temperature. In the analysis, T 0 is set as 300K.Boundary condition applied is the heat flux Fig. 3.1: Temperature Vs Thermal Conductivity The properties are evaluated at room temperature as well as elevated temperatures. Table 3.1 gives the thermal conductivity at elevated temperature. The variation of thermal conductivity with temperature is shown in Fig.3.1. It can be seen that the thermal conductivity of carbon-phenolic composite increases with increase in temperature. Table 3.2 gives the specific heat at elevated temperature. The variation of specific heat with temperature is shown in Fig.3.2. It can be seen that specific heat initially increases with increase in temperature and maintain a maximum value in the temperature range of 700K to 1000K, after that specific heat decreases with increase in temperature. ISSN: All Rights Reserved 2016 IJSETR 126
3 Table 3.2: Variation of Specific Heat with temperature Temperature(T) Specific Heat(Cp) [K] [J/kgK] Fig. 3.3: Temperature distribution on TPS at 100s. Fig. 3.2: Temperature Vs Specific heat Fig. 3.4: Temperature distribution on inner metallic backup structure at 100s 3.3 Transient Thermal Analysis Results Transient thermal analysis has been carried out up to 200s. Temperature distribution corresponding to 100s (which is the maximum heat flux condition), 180s (which is the maximum temperature condition) and 200s are considered for structural analysis. Fig. 3.5: Temperature distribution on TPS at 180s ISSN: All Rights Reserved 2016 IJSETR 127
4 Fig. 3.6: Temperature distribution on inner metallic backup structure at 180s Fig. 3.3 shows the temperature distribution on TPS at 100s and the maximum temperature is K, which is below the maximum allowable design temperature. Fig. 3.4 shows the temperature distribution on the inner metallic backup structure at 100s, which is at room temperature throughout 100s. Therefore the function of TPS is satisfied. Fig. 3.5 shows the temperature distribution on TPS at 180s and the maximum temperature is found to be K, which is below the maximum allowable design temperature. Fig. 3.6 shows the temperature distribution on the inner metallic backup structure at 180s, which is at room temperature throughout 180s. Therefore the function of TPS is satisfied. Fig. 3.8: Temperature distribution on inner metallic backup structure at 200s Fig. 3.7 shows the temperature distribution on TPS at 200s and the maximum temperature is found to be K, which is below the maximum allowable design temperature. Fig. 3.8 shows the temperature distribution on the inner metallic structure at 200s, which is at room temperature throughout 200s.. Therefore the function of TPS is satisfied. IV THERMO-STRUCTURAL ANALYSIS Structural analysis is probably the most common application of the finite element method. It is the science, which ensures safety of structures and fulfils the functions for which they have been built. Here the temperature values obtained from the transient thermal analysis is imported and applied as load along with the pressure for carrying out thermo-structural analysis at 100s,180s and 200s.The governing equation for the analysis are given below Fig. 3.7: Temperature distribution TPS at 200s Thermal-mechanical strain x = α x T + σ x / E x μ xy σ y / E x μ xz σ z / E x (3) y = α y T + μ xy σ x / E x σ y / E y μ yz σ z / E y (4) z = α z T + μ xz σ x / E x μ yz σ y / E y σ z / E z (5) (6) xy = σ xy / G xy ISSN: All Rights Reserved 2016 IJSETR 128
5 (7) (8) yz = σ yz / G yz xz = σ xz / G xz Where typical terms are: x - direct strain in x direction xy - shear strain in the x-y plane σ x - direct stress in x direction σ xy - shear stress on x-y plane 4.1 Material Properties The material properties needed for thermo-structural analysis are coefficient of thermal expansion, Young's modulus, and Shear modulus. Table 4.1: Variation of Coefficient of thermal expansion with Temperature Temperature(T) Coefficient of thermal expansion(α ) [K] [K -1 ] X-direction Y-direction Z-direction E E E E E E E E E E E E E E E E E E E E-05 The properties are evaluated at room temperature as well as elevated temperatures. Table 4.1 gives the coefficient of thermal expansion at elevated temperature. The variation of coefficient of thermal expansion with temperature is shown in Fig.4. In x and y direction coefficient of thermal expansion decreases with increase in temperature during initial stages and reaches negative value at temperature 1473K, after that it increases steadily and reaches a positive value. In z direction the coefficient of thermal expansion have positive value only during initial stages. Fig. 4.1: Coefficient of thermal expansion Vs Temperature Table 4.2: Variation of Young's Modulus with Temperature Temperature(T) [K] Young's Modulus(E) [MPa] X-direction Y-direction Z-direction Fig. 4.2: Young's Modulus Vs Temperature The properties are evaluated at room temperature as well as elevated temperatures. Table 4.2 gives the Young's Modulus at elevated temperature. The variation of Young's Modulus with temperature is shown in Fig.4.2 Young s modulus in x and y direction goes on decreasing with increase in temperature but there is a sudden rise in the value when the temperature is 873K, after that the value decreases with increase in temperature. In z direction the value of Young s modulus decreases with increase in temperature. Table 4.3: Variation of Shear Modulus with Temperature Temperature(T) [K] Shear Modulus ISSN: All Rights Reserved 2016 IJSETR 129
6 Figure 4.4: Radial deformation on TPS at 100s Fig. 4.3: Shear Modulus Vs Temperature Table 4.3 gives the Shear Modulus at elevated temperature. The variation of Shear Modulus with temperature is shown in Fig.4.3. Fig.4.3 shows that with the increase in temperature from 300K the value of shear modulus decreases but the value remains constant for a temperature range of 373K to 573K and there after it increases with increase in temperature. 4.1 Thermo-Structural Analysis Results The finite element model is run for 200s with temperature and pressure as loads. Total deformation, directional deformation and equivalent stress are obtained corresponding to 100s (which is the maximum heat flux condition), 180s (which is the maximum temperature condition) and 200s. Fig.4.4 to Fig.4.6 shows the radial deformation, hoop deformation and axial deformation on TPS at 100s respectively. The maximum radial deformation is 0.759mm, where as the maximum hoop deformation is 0.237mm and the maximum axial deformation is 1.7mm.Fig.4.7 shows the radial stress on the forward heat shield at 100s and the maximum radial stress is 147MPa. On the forward heat shield for a thickness of 0.2mm the stress values exceeds the allowable strength of 41MPa and that region will be eroded in the subsequent time instant. Fig.4.8 shows the hoop stress on the forward heat shield at 100s and the maximum hoop stress is 78MPa. The stress values exceed the allowable strength of 41MPa locally at the bolt hole. On all other regions the stress values are within the allowable limit. Fig.4.9 shows the axial stress on the forward heat shield at 100s and the maximum axial stress is 55MPa. The stress values exceeds the allowable strength of 41MPa locally at the bolt hole. On all other regions the stress values are within the allowable limit. Figure 4.5: Hoop deformation on TPS at 100s Figure 4.6: Axial deformation on TPS at 100s Figure 4.7: Radial stress on forward heat shield at 100s ISSN: All Rights Reserved 2016 IJSETR 130
7 Figure 4.8: Hoop stress on forward heat shield at 100s Figure 4.10: Radial stress on flare region at 100s Figure 4.9: Axial stress on forward heat shield at 100s Fig.4.10 shows the radial stress on flare region at 100s and the maximum radial stress is 90MPa. On the flare region for a thickness of 0.2mm the stress values exceeds the allowable strength of 41MPa and that region will be eroded in the subsequent time instant.fig.4.11 shows the hoop stress on the flare region at 100s and the maximum hoop stress is 300MPa. The stress values exceed the allowable strength of 41MPa locally at some regions. On all other regions the stress values are within the allowable limit. Fig.4.12 shows the axial stress on flare region at 100s and the maximum axial stress is 138MPa. On the flare region for a thickness of 0.2mm the stress values exceeds the allowable strength of 41MPa and that region will be eroded in the subsequent time instant. Figure 4.11: Hoop stress on flare region at 100s Figure 4.12: Axial stress on flare region at 100s ISSN: All Rights Reserved 2016 IJSETR 131
8 Figure 4.13: Radial stress on conical heat shield at 100s Fig.4.13 shows the radial stress on conical heat shield at 100s and the maximum radial stress is 188MPa. The stress values exceed the allowable strength of 41MPa locally at the bolt hole. On all other regions the stress values are within the allowable limit. Fig.4.14 shows the hoop stress on the conical heat shield at 100s and the maximum hoop stress is 136MPa. On the conical heat shield for a thickness of 0.2mm the stress values exceeds the allowable strength of 41MPa and that region will be eroded in the subsequent time instant. Fig.4.15 shows the axial stress on conical heat shield at 100s and the maximum axial stress is 109MPa. The stress values exceed the allowable strength of 41MPa locally at the bolt hole. On all other regions the stress values are within the allowable limit.fig.4.16 shows the equivalent stress on inner metallic backup structure at 100s and the maximum value is found to be MPa which is below the allowable strength of 375MPa. Figure 4.14: Hoop stress on conical heat shield at 100s Figure 4.15: Axial stress on conical heat shield at 100s Figure 4.16: Equivalent stress on inner metallic backup structure at 100s Fig.4.17 to Fig.4.19 shows the radial deformation, hoop deformation and axial deformation on TPS at 180s respectively. The maximum radial deformation is 1.43mm, where as the maximum hoop deformation is 0.379mm and the maximum axial deformation is 1.96mm. Fig.4.20 shows the radial stress on the forward heat shield at 180s and the maximum radial stress is 110MPa. On the forward heat shield for a thickness of 0.5mm the stress values exceeds the allowable strength of 41MPa and that region will be eroded in the subsequent time instant. Fig.4.21 shows the hoop stress on the forward heat shield at 180s and the maximum hoop stress is 86MPa. The stress values exceed the allowable strength of 41MPa locally at the bolt hole. On all other regions the stress values are within the allowable limit. Fig.4.22 shows the axial stress on the forward heat shield at 180s and the maximum axial stress is 55MPa The stress values exceeds the allowable strength of 41MPa locally at the bolt hole. On all other regions the stress values are within the allowable limit. ISSN: All Rights Reserved 2016 IJSETR 132
9 Figure 4.17: Radial deformation on TPS at 180s Figure 4.20: Radial stress on forward heat shield at 180s Figure 4.18: Hoop deformation on TPS at 180s Figure 4.21: Hoop stress on forward heat shield at 180s Figure 4.19: Axial deformation on TPS at 180s Fig.4.23 shows the radial stress on flare region at 180s and the maximum radial stress is 178MPa. On the flare region for a thickness of 0.5mm the stress values exceeds the allowable strength of 41MPa and that region will be eroded in the subsequent time instant.fig.4.24 shows the hoop stress on the flare region at 180s and the maximum hoop stress is 384MPa. The stress values exceed the allowable strength of 41MPa locally at some regions. On all other regions the stress values are within the allowable limit. Fig.4.25 shows the axial stress on flare region at 180s and the maximum axial stress is 322MPa. On the flare region for a thickness of 0.5mm the stress values exceeds the allowable strength of 41MPa and that region will be eroded in the subsequent time instant. Figure 4.22: Axial stress on forward heat shield at 180s Fig.4.26 shows the radial stress on conical heat shield at 180s and the maximum radial stress is 238MPa. The stress values exceed the allowable strength of 41MPa locally at some regions. On all other regions the stress values are within the allowable limit. Fig.4.27 shows the hoop stress on the conical heat shield at 180s and the maximum hoop stress is 395MPa. On the conical heat shield for a thickness of 0.5mm the stress values exceeds the allowable strength of 41MPa and that region will be eroded in the subsequent time instant. Fig.4.28 shows the axial stress on conical heat shield at 180s and the maximum axial stress is 290MPa. On the conical heat shield for a thickness of 0.5mm the stress values exceeds the ISSN: All Rights Reserved 2016 IJSETR 133
10 allowable strength of 41MPa and that region will be eroded in the subsequent time instant. Figure 4.26: Radial stress on conical heat shield at 180s Figure 4.23: Radial stress on flare region at 180s Figure 4.27: Hoop stress on conical heat shield at 180s Figure 4.24: Hoop stress on flare region at 180s Figure 4.28: Axial stress on conical heat shield at 180s Figure 4.25: Axial stress on flare region at 180s Figure 4.29: Equivalent stress on inner metallic backup ISSN: All Rights Reserved 2016 IJSETR 134
11 structure at 180s Fig.4.29 shows the equivalent stress on inner metallic backup structure at 180s and the maximum value is found to be MPa which is below the allowable strength of 375MPa. bolt hole. On all other regions the stress values are within the allowable limit. Figure 4.30: Radial deformation on TPS at 200s Figure 4.33: Radial stress on forward heat shield at 200s Figure 4.31: Hoop deformation on TPS at 200s Figure 4.34: Hoop stress on forward heat shield at 200s Figure 4.32: Axial deformation on TPS at 200s Fig.4.30 to Fig.4.32 shows the radial deformation, hoop deformation and axial deformation on TPS at 180s respectively. The maximum radial deformation is 1.57mm, where as the maximum hoop deformation is 0.39mm and the maximum axial deformation is 2.04mm. Fig.4.33 shows the radial stress on the forward heat shield at 200s and the maximum radial stress is 110MPa. On the forward heat shield the stress values exceeds the allowable strength of 41MP for a thickness of 0.75mm, which is only 1.5% of total thickness 50mm. Therefore the forward heat shield configuration is safe. Fig.4.34 shows the hoop stress on the forward heat shield at 200s and the maximum hoop stress is 85MPa. The stress values exceed the allowable strength of 41MPa locally at the bolt hole. On all other regions the stress values are within the allowable limit. Fig.4.35 shows the axial stress on the forward heat shield at 200s and the maximum axial stress is 61MPa The stress values exceeds the allowable strength of 41MPa locally at the Figure 4.35: Axial stress on forward heat shield at 200s Fig.4.36 shows the radial stress on flare region at 200s and the maximum radial stress is 173MPa. On the flare region he stress values exceeds the allowable strength of 41MP for a thickness of 0.75mm, which is only 1.5% of total thickness 50mm. Therefore the flare region is safe. Fig.4.37 shows the hoop stress on the flare region at 200s and the maximum hoop stress is 380MPa. The stress values exceed the allowable strength of 41MPa locally at some regions. On all other regions the stress values are within the allowable limit. Fig.4.38 shows the axial stress on flare region at 200s and the maximum axial stress is 316MPa. On the flare region he stress values exceeds the allowable strength of 41MP for a thickness of 0.75mm, which is only 1.5% of total thickness 50mm. Therefore the flare region is safe. Fig.4.39 shows the radial stress on conical heat shield at 200s and the maximum radial stress is 246MPa. The stress ISSN: All Rights Reserved 2016 IJSETR 135
12 values exceed the allowable strength of 41MPa locally at some regions. On all other regions the stress values are within the allowable limit. Fig.4.40 shows the hoop stress on the conical heat shield at 200s and the maximum hoop stress is 392MPa. On the conical heat shield the stress values exceeds the allowable strength of 41MP for a thickness of 0.75mm, which is only 1.5% of total thickness 50mm. Therefore the conical heat shield configuration is safe. Fig.4.41 shows the axial stress on conical heat shield at 200s and the maximum axial stress is 298MPa. On the conical heat shield the stress values exceeds the allowable strength of 41MP for a thickness of 0.75mm, which is only 1.5% of total thickness 50mm. Therefore the conical heat shield configuration is safe. Figure 4.38: Axial stress on flare region at 200s Figure 4.36: Radial stress on flare region at 200s Figure 4.39: Radial stress on conical heat shield at 200s Figure 4.37: Hoop stress on flare region at 200s Figure 4.40: Hoop stress on conical heat shield at 200s ISSN: All Rights Reserved 2016 IJSETR 136
13 Thermo-structural analysis was carried out at 100s (which is the maximum heat flux condition), 180s (which is the maximum temperature condition) and 200s to assess the deformations and stresses. The maximum radial deformation, hoop deformation and axial deformations are 1.57mm, 0.39mm and 2.04mm respectively (at 200s) which are within the desired limit. At 200s the stress values on the TPS exceeds the allowable strength of 41MPa for a thickness of 0.75mm which is only 1.5% of total thickness 50mm.On all other regions the stress values are within the allowable limit. Therefore the carbon-phenolic TPS configuration is safe. Also the equivalent stress on inner metallic backup structure is below the allowable strength of 375MPa for the entire flight duration. Figure 4.41: Axial stress on conical heat shield at 200s Fig.4.42 shows the equivalent stress on inner metallic backup structure at 100s and the maximum value is found to be 353MPa which is below the allowable strength of 375MPa. REFERENCES [1] Santhosh,B., Thermo-Structural Analysis of 3D Composites for Reusable Applications, Proceedings of 2 nd International Conference on Materials for the Future(ICMF),2011. [2] Roberto,Silva., Direct Coupled Thermo- Structural analysis in ANSYS, Proceedings of ESSS Conference, Bourbon Atibaia,2013. [3] Thirapat,Kitinirunkul., Affecting Factors of the Mechanical Properties to Phenolic Fibre Composite, World Academy of Science, Engineering and Technology, International Journal of Chemical, Nuclear, Metallurgical and Materials Engineering Vol : 7 No: 10, [4] Zinchengo,V. I., Thermal degradation of a carbon phenolic composite in a high-temperature gas flow, January February, 1995, Volume 31, Issue 1,pp [5] Suneeth,Sukumaran., Design and Analysis of Metallic Thermal Protection Systems,International Journal of Scientific and Research Publications, Volume 1 ISSN , Issue 2, February Figure 4.42: Equivalent stress on inner metallic backup structure at 200s V CONCLUSION Transient thermal analysis was carried out to obtain temperature distribution in a TPS of re-entry module called Crew module which is developed by ISRO. The flight duration was 200s and temperature distribution corresponding 100s (which is the maximum heat flux condition), 180s (which is the maximum temperature condition) and 200s are obtained for structural analysis. The maximum temperature obtained is (at 180s) and is found to be below maximum allowable design temperature of the carbon-phenolic composite with which the TPS is made, also the inner metallic structure is maintained at room temperature during the entire flight duration. Therefore the function of the TPS is satisfied. ISSN: All Rights Reserved 2016 IJSETR 137
Analysis of a Casted Control Surface using Bi-Linear Kinematic Hardening
Analysis of a Casted Control Surface using Bi-Linear Kinematic Hardening Abdul Manan Haroon A. Baluch AERO, P.O Box 91, Wah Cantt. 47040 Pakistan Abstract Control Surfaces or Fins are very essential parts
More informationThermo-mechanical Investigation of Ventilated Disc Brake with Finite Element Analysis
Thermo-mechanical Investigation of Ventilated Disc Brake with Finite Element Analysis Arifin #1, Mohammad Tauviqirrahman #2, Muchammad *3, J. Jamari #, A.P. Bayuseno # # Laboratory for Engineering Design
More informationN = Shear stress / Shear strain
UNIT - I 1. What is meant by factor of safety? [A/M-15] It is the ratio between ultimate stress to the working stress. Factor of safety = Ultimate stress Permissible stress 2. Define Resilience. [A/M-15]
More informationAN ANALYSIS TO THERMAL LOAD AND MECHANICAL LOAD COUPLING OF A GASOLINE ENGINE PISTON
0 th February 013. Vol. 48 No. 005-013 JATIT & LLS. All rights reserved. ISSN: 199-8645 www.jatit.org E-ISSN: 1817-3195 AN ANALYSIS TO THERMAL LOAD AND MECHANICAL LOAD COUPLING OF A GASOLINE ENGINE PISTON
More informationThermo Mechanical Analysis of AV1 Diesel Engine Piston using FEM
Journal of Advanced Engineering Research ISSN: 2393-8447 Volume 2, Issue 1, 2015, pp.23-28 Thermo Mechanical Analysis of AV1 Diesel Engine Piston using FEM Subodh Kumar Sharma 1, *, P. K. Saini 2, N. K.
More informationFinite Element Modeling for Transient Thermal- Structural Coupled Field Analysis of a Pipe Joint
International Conference on Challenges and Opportunities in Mechanical Engineering, Industrial Engineering and Management Studies 88 Finite Element Modeling for Transient Thermal- Structural Coupled Field
More informationPYROLYSIS MODELLING AND EXPERIMENTATION FOR THERMO-PHYSICAL PROPERTIES OF CHAR FORMED FROM ABLATIVE MATERIAL
PYROLYSIS MODELLING AND EXPERIMENTATION FOR THERMO-PHYSICAL PROPERTIES OF CHAR FORMED FROM ABLATIVE 1 S.V. Aravind Pulickel, 2 Mangesh. B. Chaudhari 1,2 Vishwakarma Institute of Technology Pune, India
More informationDesign and Structural Analysis of Propulsion Module for Sample Return Mission to 2010TK7
Design and Structural Analysis of Propulsion Module for Sample Return Mission to 2010TK7 A Rathan Babu, Y Shwetha, G S D Madhav, R Suresh Kumar Department of Aeronautical Engineering, Institute of Aeronautical
More informationStresses Analysis of Petroleum Pipe Finite Element under Internal Pressure
ISSN : 48-96, Vol. 6, Issue 8, ( Part -4 August 06, pp.3-38 RESEARCH ARTICLE Stresses Analysis of Petroleum Pipe Finite Element under Internal Pressure Dr.Ragbe.M.Abdusslam Eng. Khaled.S.Bagar ABSTRACT
More informationThe Dynamical Loading of the WWER440/V213 Reactor Pressure Vessel Internals during LOCA Accident in Hot and Cold Leg of the Primary Circuit
The Dynamical Loading of the WWER440/V213 Reactor Pressure Vessel Internals during LOCA Accident in Hot and Cold Leg of the Primary Circuit ABSTRACT Peter Hermansky, Marian Krajčovič VUJE, Inc. Okružná
More informationSIMULATION STUDIES ON THE EFFECT OF PROJECTILE NOSE SHAPE IMPACTING ON ALUMINUM PLATES
Int. J. Mech. Eng. & Rob. Res. 2014 Sivaiah A et al., 2014 Research Paper ISSN 2278 0149 www.ijmerr.com Vol. 3, No. 1, January 2014 2014 IJMERR. All Rights Reserved SIMULATION STUDIES ON THE EFFECT OF
More informationUniversity of Sheffield The development of finite elements for 3D structural analysis in fire
The development of finite elements for 3D structural analysis in fire Chaoming Yu, I. W. Burgess, Z. Huang, R. J. Plank Department of Civil and Structural Engineering StiFF 05/09/2006 3D composite structures
More informationDesign and Analysis of Metallic Thermal Protection System (MTPS)
International Journal of Scientific and Research Publications, Volume 3, Issue 2, February 2013 1 Design and Analysis of Metallic Thermal Protection System (MTPS) Suneeth Sukumaran*, Dr.S.H.Anilkumar**
More informationAluminum shell. Brass core. 40 in
PROBLEM #1 (22 points) A solid brass core is connected to a hollow rod made of aluminum. Both are attached at each end to a rigid plate as shown in Fig. 1. The moduli of aluminum and brass are EA=11,000
More informationCHAPTER 7 FINITE ELEMENT ANALYSIS OF DEEP GROOVE BALL BEARING
113 CHAPTER 7 FINITE ELEMENT ANALYSIS OF DEEP GROOVE BALL BEARING 7. 1 INTRODUCTION Finite element computational methodology for rolling contact analysis of the bearing was proposed and it has several
More informationSamantha Ramirez, MSE. Stress. The intensity of the internal force acting on a specific plane (area) passing through a point. F 2
Samantha Ramirez, MSE Stress The intensity of the internal force acting on a specific plane (area) passing through a point. Δ ΔA Δ z Δ 1 2 ΔA Δ x Δ y ΔA is an infinitesimal size area with a uniform force
More informationTHERMO-MECHANICAL ANALYSIS OF A COPPER VAPOR LASER
THERMO-MECHANICAL ANALYSIS OF A COPPER VAPOR LASER E.mail: rchaube@cat.ernet.in R. CHAUBE, B. SINGH Abstract The thermal properties of the laser head such as temperature distribution, thermal gradient
More informationEARLY AGE THERMAL CRACK CONTROL IN MASS CONCRETE
EARLY AGE THERMAL CRACK CONTROL IN MASS CONCRETE A.W.R.M.G.W.D.B. Girihagama * and S.M.A. Nanayakkara University of Moratuwa, Colombo, Sri Lanka *E-mail: danu.girihagama.uom @ gmail.com, TP: +94711352729
More informationA PAPER ON DESIGN AND ANALYSIS OF PRESSURE VESSEL
A PAPER ON DESIGN AND ANALYSIS OF PRESSURE VESSEL P.Palanivelu 1, R.Siva Prasad 2, 1 PG Scholar, Department of Mechanical Engineering, Gojan School of Business and Technology, Redhills, Chennai, India.
More informationComparison of Ply-wise Stress-Strain results for graphite/epoxy laminated plate subjected to in-plane normal loads using CLT and ANSYS ACP PrepPost
Comparison of Ply-wise Stress-Strain results for graphite/epoxy laminated plate subjected to in-plane normal loads using CLT and ANSYS ACP PrepPost 1 Mihir A. Mehta, 2 Satyen D. Ramani 1 PG Student, Department
More informationFinite Element Method in Geotechnical Engineering
Finite Element Method in Geotechnical Engineering Short Course on + Dynamics Boulder, Colorado January 5-8, 2004 Stein Sture Professor of Civil Engineering University of Colorado at Boulder Contents Steps
More informationStructural Integrity Analysis of Propellant in Solid Rocket Motor
Structural Integrity Analysis of Propellant in Solid Rocket Motor Tejas Nikam 1, Mrunal Pardeshi 2, Amit Patil 3, Akshay Patkure 4, Manoday Ramteke 5 1 UG Student, Mechanical Engineering Department, Smt.
More informationModal and Static Structural Analysis of Exhaust Collector Box for Compressor test facility
Modal and Static Structural Analysis of Exhaust Collector Box for Compressor test facility Shankar Gouda 1, Praveen M P 2 P G student, Department of Mechanical Engineering, EPCET, Bangalore, Karnataka,
More informationPreliminary AD-Horn Thermomechanical and Electrodynamic Simulations
CERN-ACC-2016-0334 2016-12-12 edmundo.lopez.sola@cern.ch Preliminary AD-Horn Thermomechanical and Electrodynamic Simulations Edmundo Lopez Sola / EN-STI, David Horvath / EN-STI, Marco Calviani / EN-STI
More informationSpace mission environments: sources for loading and structural requirements
Space structures Space mission environments: sources for loading and structural requirements Prof. P. Gaudenzi Università di Roma La Sapienza, Rome Italy paolo.gaudenzi@uniroma1.it 1 THE STRUCTURAL SYSTEM
More informationMars Ascent Vehicle Hybrid Motor Structural Analysis
Mars Ascent Vehicle Hybrid Motor Structural Analysis MSFC - James Luce ER41 (Summer intern program) NASA Sensitive But Unclassified 1 Background: the MAV MAV: Mars Ascent Vehicle (MAV) is a small rocket
More informationA Numerical Study on Static and Dynamic Characteristics of Electromagnetic Air Compressor used in Household Refrigerators
Journal of Experimental & Applied Mechanics ISSN: 2230-9845 (online), ISSN: 2321-516X (print) Volume 5, Issue 3 www.stmjournals.com A Numerical Study on Static and Dynamic Characteristics of Electromagnetic
More informationCFD Analysis and Comparison of Different Ventilation Geometries for Brake Discs
CFD Analysis and Comparison of Different Ventilation Geometries for Brake Discs Vijay Gautam DTU, Delhi, India 110042 vijaygautam@dce.ac.in Ananya Bhardwaj DTU, Delhi, India 110042 ananyabhardwaj22@gmail.com
More informationAnalysis of Flow Regulating Pressure Valve by using Finite Element Analysis
IJIRST International Journal for Innovative Research in Science & Technology Volume 3 Issue 05 October 2016 ISSN (online): 2349-6010 Analysis of Flow Regulating Pressure Valve by using Finite Element Analysis
More informationFinite element simulation of residual stresses in laser heating
IAS-2008-66-546ST Finite element simulation of residual stresses in laser heating G. H. Farrahi 1, M. Sistaninia 2, H. Moeinoddini 3 1,2-School of Mechanical Engineering, Sharif University of Technology,
More informationSTRUCTURAL ANALYSIS OF THE LIFTING DEVICE DETECTOR SUPPORTS FOR THE LHCb VERTEX LOCATOR (VELO)
National Institute for Nuclear Physics and High Energy Physics Kruislaan 409 1098 SJ Amsterdam The Netherlands NIKHEF Reference no.: MT-VELO 04-2 EDMS no: 466608 OF THE LIFTING DEVICE DETECTOR SUPPORTS
More information[Maddu, 5(12): December2018] ISSN DOI /zenodo Impact Factor
GLOBAL JOURNAL OF ENGINEERING SCIENCE AND RESEARCHES ANALYSIS OF RADIATOR FAN OF WDM-2 LOCO ENGINE FOR EFFICIENCY IMPROVEMENT Yesu Ratnam. Maddu *1, K.Divakara Murthy 2 & Shaik Saidulu 3 *1,3 Assistant
More informationHEAT TRANSFER AND THERMAL STRESS ANALYSIS OF WATER COOLING JACKET FOR ROCKET EXHAUST SYSTEMS
HEAT TRANSFER AND THERMAL STRESS ANALYSIS OF WATER COOLING JACKET FOR ROCKET EXHAUST SYSTEMS Mihai MIHAILA-ANDRES 1 Paul Virgil ROSU 2 Ion FUIOREA 3 1 PhD., Structure Analysis and Simulation Division,
More informationCHAPTER 3 THE EFFECTS OF FORCES ON MATERIALS
CHAPTER THE EFFECTS OF FORCES ON MATERIALS EXERCISE 1, Page 50 1. A rectangular bar having a cross-sectional area of 80 mm has a tensile force of 0 kn applied to it. Determine the stress in the bar. Stress
More informationTutorial for the heated pipe with constant fluid properties in STAR-CCM+
Tutorial for the heated pipe with constant fluid properties in STAR-CCM+ For performing this tutorial, it is necessary to have already studied the tutorial on the upward bend. In fact, after getting abilities
More informationANALYSIS OF THERMAL STRESSES OF SOLAR PARABOLIC TROUGH COLLECTOR FOR SOLAR POWER PLANT BY FEM
Research Paper ISSN 2278 0149 www.ijmerr.com Vol. 3, No. 2, April, 2014 2014 IJMERR. All Rights Reserved ANALYSIS OF THERMAL STRESSES OF SOLAR PARABOLIC TROUGH COLLECTOR FOR SOLAR POWER PLANT BY FEM K
More informationNUMERICAL INVESTIGATION OF A THREE-DIMENSIONAL DISC-PAD MODEL WITH AND WITHOUT THERMAL EFFECTS
THERMAL SCIENCE: Year 2015, Vol. 19, No. 6, pp. 2195-2204 2195 NUMERICAL INVESTIGATION OF A THREE-DIMENSIONAL DISC-PAD MODEL WITH AND WITHOUT THERMAL EFFECTS by Ali BELHOCINE * Faculty of Mechanical Engineering,
More informationTHERMO-MECHANICAL ANALYSIS IN PERFORATED ANNULAR FIN USING ANSYS
THERMO-MECHANICAL ANALYSIS IN PERFORATED ANNULAR FIN USING ANSYS Kunal Adhikary 1, Dr. Ashis Mallick 2 1,2 Department of Mechanical Engineering, IIT(ISM), Dhanbad-826004, Jharkhand, India Abstract Thermal
More informationModule 2: Thermal Stresses in a 1D Beam Fixed at Both Ends
Module 2: Thermal Stresses in a 1D Beam Fixed at Both Ends Table of Contents Problem Description 2 Theory 2 Preprocessor 3 Scalar Parameters 3 Real Constants and Material Properties 4 Geometry 6 Meshing
More informationTransient Coupled Field Solution for a Pion / Muon Collector
Transient Coupled Field Solution for a Pion / Muon Collector Mike Yaksh Yaksh Magnetic Solutions 1 Some background on Pion/Muon Collection An axial magnetic field is generated by current flowing in circumferential
More informationThermo-Elastic Stress Analysis of the GHARR-1 Vessel during Reactor Operation Using ANSYS 13.0
Journal of Emerging Trends in Engineering and Applied Sciences (JETEAS) 6(5): 309-314 Scholarlink Research Institute Journals, 2015 (ISSN: 2141-7016) jeteas.scholarlinkresearch.com Journal of Emerging
More informationStress Analysis of Mandrel Used In Pilger Technology
Stress Analysis of Mandrel Used In Pilger Technology Ruchil A. Patel 1, Apurvkumar Patel 2, Rajesh Kumar 3, Dr. D. V. Patel 4 1, 2, 3,4 Mechanical Engineering, GTU, Ahmedabad Abstract Cold pilgering is
More informationJadavpur University, Kolkata
Finite Element Analysis of Transient Thermo Mechanical Stresses of Multilayered Composite Hollow Thick Cylindrical Pressure Vessel Arnab Choudhury 1, Samar Chandra Mondol 2, Susenjit Sarkar 3 1 Research
More informationSTRUCTURAL ANALYSIS OF A WESTFALL 2800 MIXER, BETA = 0.8 GFS R1. By Kimbal A. Hall, PE. Submitted to: WESTFALL MANUFACTURING COMPANY
STRUCTURAL ANALYSIS OF A WESTFALL 2800 MIXER, BETA = 0.8 GFS-411519-1R1 By Kimbal A. Hall, PE Submitted to: WESTFALL MANUFACTURING COMPANY OCTOBER 2011 ALDEN RESEARCH LABORATORY, INC. 30 Shrewsbury Street
More informationVEGA LAUNCH VEHICLE: PAYLOAD FAIRING SEPARATION ANALYSIS
VEGA LAUNCH VEHICLE: PAYLOAD FAIRING SEPARATION ANALYSIS P. F. Dezio, E. Mastrella, D. Fotino, G. Leto, M. Linari, F. Battie, D. Barbagallo The Payload Fairing (PLF) is the upper structural part of a launcher.
More informationTOPOLOGY OPTIMIZATION OF A CURVED THERMAL PROTECTION SYSTEM
TOPOLOGY OPTIMIZATION OF A CURVED THERMAL PROTECTION SYSTEM A thesis submitted in partial fulfillment of the requirements for the degree of Master of Science in Engineering By MUTHUMANIKANDAN PRITHIVIRAJ
More informationCritical Load columns buckling critical load
Buckling of Columns Buckling of Columns Critical Load Some member may be subjected to compressive loadings, and if these members are long enough to cause the member to deflect laterally or sideway. To
More informationOPTIMAL DESIGN OF CLUTCH PLATE BASED ON HEAT AND STRUCTURAL PARAMETERS USING CFD AND FEA
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 5, May 2018, pp. 717 724, Article ID: IJMET_09_05_079 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=5
More informationStress and Temperature Distribution Study in a Functionally Graded Brake Disk
Stress and Temperature Distribution Study in a Functionally Graded Brake Disk P. Hosseini Tehrani, M.Talebi2 Assistant professor, 2 MS c. Student, Center of excellence in railway transportation, School
More informationStrength analysis on load rejection working condition of steam turbine
Strength analysis on load rejection working condition of steam turbine WANG Gongyi, CHENG Kai, YANG Jiandao, YU Deqi, GU Luyin, PENG Zeying Shanghai Turbine Works Co., Ltd., Shanghai 201612, China Abstract:
More informationIntroduction to Atmospheric Flight. Dr. Guven Aerospace Engineer (P.hD)
Introduction to Atmospheric Flight Dr. Guven Aerospace Engineer (P.hD) What is Atmospheric Flight? There are many different ways in which Aerospace engineering is associated with atmospheric flight concepts.
More informationOn The Temperature and Residual Stress Field During Grinding
On The Temperature and Residual Stress Field During Grinding S. M. H-Gangaraj, G. H. Farrahi and H. Ghadbeigi Abstract Grinding is widely used for manufacturing of components that require fine surface
More informationProbabilistic design of helical coil spring for Translational invariance by using Finite Element Method
Probabilistic design of helical coil spring for Translational invariance by using Finite Element Method Sagar N Khurd, Prasad P Kulkarni, Samir D Katekar 1Research scholar, Department of mechanical Engineering,
More informationDesign and Dynamic Analysis of Flywheel
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684, p-issn : 2320 334X PP 51-56 www.iosrjournals.org Design and Dynamic Analysis of Flywheel T. Raja Santhosh Kumar 1, Suresh
More informationJeff Brown Hope College, Department of Engineering, 27 Graves Pl., Holland, Michigan, USA UNESCO EOLSS
MECHANICS OF MATERIALS Jeff Brown Hope College, Department of Engineering, 27 Graves Pl., Holland, Michigan, USA Keywords: Solid mechanics, stress, strain, yield strength Contents 1. Introduction 2. Stress
More informationTransient Analysis of Disk Brake By using Ansys Software
Transient Analysis of Disk Brake By using Ansys Software G. Babukanth & M. Vimal Teja Department of Mechanical Engineering, Nimra College of Engineering & Technology, Ibrahimpatnam, Vijayawada E-mail :
More informationComputational Fluid Dynamics Analysis of Advanced Rocket Nozzle
Research Article International Journal of Current Engineering and Technology E-ISSN 2277 4106, P-ISSN 2347-5161 2014 INPRESSCO, All Rights Reserved Available at http://inpressco.com/category/ijcet Computational
More informationSingle Stop Transient Thermal Coupled with Structural Analysis and Repeated Braking Analysis with Convective Cooling for Ventilated Rotor
Single Stop Transient Thermal Coupled with Structural Analysis and Repeated Braking Analysis with Convective Cooling for Ventilated Rotor Tirth Sodagar 1, Avadhoot Ahire 2 1Tirth Sodagar, Student, School
More informationFRICTION AND WEAR OF CARBON-CARBON COMPOSITE PART 2: TEMPERATURE AND STRESS FIELDS ANALYSIS
FRICTION AND WEAR OF CARBON-CARBON COMPOSITE PART 2: TEMPERATURE AND STRESS FIELDS ANALYSIS Kia-Moh Teo and Khalid Lafdi NSF-University-Industry Center For Advanced Friction Studies, Southern Illinois
More informationMECE 3321 MECHANICS OF SOLIDS CHAPTER 1
MECE 3321 MECHANICS O SOLIDS CHAPTER 1 Samantha Ramirez, MSE WHAT IS MECHANICS O MATERIALS? Rigid Bodies Statics Dynamics Mechanics Deformable Bodies Solids/Mech. Of Materials luids 1 WHAT IS MECHANICS
More informationINTERNATIONAL JOURNAL OF APPLIED ENGINEERING RESEARCH, DINDIGUL Volume 2, No 1, 2011
Interlaminar failure analysis of FRP cross ply laminate with elliptical cutout Venkateswara Rao.S 1, Sd. Abdul Kalam 1, Srilakshmi.S 1, Bala Krishna Murthy.V 2 1 Mechanical Engineering Department, P. V.
More informationTheory at a Glance (for IES, GATE, PSU)
1. Stress and Strain Theory at a Glance (for IES, GATE, PSU) 1.1 Stress () When a material is subjected to an external force, a resisting force is set up within the component. The internal resistance force
More informationArberi Ferraj. Wentworth Institute of Technology. Design of Machine Elements MECH 420
P a g e 1 Arberi Ferraj Wentworth Institute of Technology Design of Machine Elements MECH 420 P a g e 2 1. Executive Summary A scissor car jack was designed and must be reverse-engineered in order to discover
More informationStress Transformation Equations: u = +135 (Fig. a) s x = 80 MPa s y = 0 t xy = 45 MPa. we obtain, cos u + t xy sin 2u. s x = s x + s y.
014 Pearson Education, Inc., Upper Saddle River, NJ. All rights reserved. This material is protected under all copyright laws as they currently 9 7. Determine the normal stress and shear stress acting
More informationCrack Tip Plastic Zone under Mode I Loading and the Non-singular T zz -stress
Crack Tip Plastic Zone under Mode Loading and the Non-singular T -stress Yu.G. Matvienko Mechanical Engineering Research nstitute of the Russian Academy of Sciences Email: ygmatvienko@gmail.com Abstract:
More informationMembers Subjected to Torsional Loads
Members Subjected to Torsional Loads Torsion of circular shafts Definition of Torsion: Consider a shaft rigidly clamped at one end and twisted at the other end by a torque T = F.d applied in a plane perpendicular
More informationINVESTIGATION OF STRESSES IN MASTER LEAF OF LEAF SPRING BY FEM AND ITS EXPERIMENTAL VERIFICATION
INVESTIGATION OF STRESSES IN MASTER LEAF OF LEAF SPRING BY FEM AND ITS EXPERIMENTAL VERIFICATION * R. B. Charde, **Dr. D.V. Bhope, * P.G. Student, Department Of Mech. Engg., Rajiv Gandhi College Of Engineering
More informationNumerical Approach to Predict the Strength of St. Peter Sandstone Pillars acted upon by Vertical Loads A case study at Clayton, IA, USA.
IOSR Journal of Engineering (IOSRJEN) ISSN (e): 2250-3021, ISSN (p): 2278-8719 Vol. 05, Issue 01 (January. 2015), V2 PP 36-41 www.iosrjen.org Numerical Approach to Predict the Strength of St. Peter Sandstone
More informationA.0 IDUKKI ARCH DAM - ANALYSIS FOR VARIOUS LOAD CASES AND DISCRETISATIONS
Annexure A.0 IDUKKI ARCH DAM - ANALYSIS FOR VARIOUS LOAD CASES AND DISCRETISATIONS In this Annexure, Idukki arch dam chosen for case study is analyzed with the developed program for various load conditions
More informationROTATING RING. Volume of small element = Rdθbt if weight density of ring = ρ weight of small element = ρrbtdθ. Figure 1 Rotating ring
ROTATIONAL STRESSES INTRODUCTION High centrifugal forces are developed in machine components rotating at a high angular speed of the order of 100 to 500 revolutions per second (rps). High centrifugal force
More informationA Finite Element approach for the design of innovative ablative materials for space applications
6 TH EUROPEAN CONFERENCE FOR AERONAUTICS AND SPACE SCIENCES (EUCASS) A Finite Element approach for the design of innovative ablative materials for space applications Valerio Carandente*, Roberto Scigliano,
More informationSIMPLIFIED METHOD FOR PREDICTING DEFORMATIONS OF RC FRAMES DURING FIRE EXPOSURE
SIMPLIFIED METHOD FOR PREDICTING DEFORMATIONS OF RC FRAMES DURING FIRE EXPOSURE M.A. Youssef a, S.F. El-Fitiany a a Western University, Faculty of Engineering, London, Ontario, Canada Abstract Structural
More informationFinite Element Analysis of Web Type Flywheel Made of Composite Material
Finite Element Analysis of Web Type Flywheel Made of Composite Material Amol Chougule #1, S. B. Tuljapure *2, # Student, M.E (Design) #1, Associate Professor *2 Department of Mechanical Engineering Solapur
More informationUNIVERSITY OF SASKATCHEWAN ME MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich
UNIVERSITY OF SASKATCHEWAN ME 313.3 MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS For Marker s Use Only LAST NAME (printed): FIRST
More informationFig. 1. Circular fiber and interphase between the fiber and the matrix.
Finite element unit cell model based on ABAQUS for fiber reinforced composites Tian Tang Composites Manufacturing & Simulation Center, Purdue University West Lafayette, IN 47906 1. Problem Statement In
More informationDesign and Finite Element Analysis of Helmeted Head Form in Impact
, pp.15-24 http://dx.doi.org/10.14257/ijast.2016.93.02 Design and Finite Element Analysis of Helmeted Head Form in Impact Suddapalli Praneeth Babu* 1 and Dr. Chandana Srinivas 2 1 Mechanical Engineering,
More informationObservational Methods and
Observational Methods and NATM System for Observational approach to tunnel design Eurocode 7 (EC7) includes the following remarks concerning an observational method. Four requirements shall all be made
More informationReliability Prediction for a Thermal System Using CFD and FEM Simulations
Proceedings of IMECE2008 2008 ASME International Mechanical Engineering Congress and Exposition October 31 - November 6, 2008, Boston, Massachusetts, USA IMECE2008-68365 Reliability Prediction for a Thermal
More informationPractice Final Examination. Please initial the statement below to show that you have read it
EN175: Advanced Mechanics of Solids Practice Final Examination School of Engineering Brown University NAME: General Instructions No collaboration of any kind is permitted on this examination. You may use
More informationCFD Analysis of the Effect of Material Properties of Nose Cone on the Heat Flux and Thermal Field during Re-entry of Space Vehicle
CFD Analysis of the Effect of Material Properties of Nose Cone on the Heat Flux and Thermal Field during Re-entry of Space Vehicle [1] K.V.Sreenivas Rao, [2] Sujan.P, [3] Sachin H.S [1] Professor, [2][3]
More information16.20 HANDOUT #2 Fall, 2002 Review of General Elasticity
6.20 HANDOUT #2 Fall, 2002 Review of General Elasticity NOTATION REVIEW (e.g., for strain) Engineering Contracted Engineering Tensor Tensor ε x = ε = ε xx = ε ε y = ε 2 = ε yy = ε 22 ε z = ε 3 = ε zz =
More informationNumerical Analysis of Fluid Flow and Heat Transfer Characteristics of Ventilated Disc Brake Rotor Using CFD
International Journal of Engineering Inventions e-issn: 2278-7461, p-issn: 2319-6491 Volume 4, Issue 10 [June 2015] PP: 31-38 Numerical Analysis of Fluid Flow and Heat Transfer Characteristics of Ventilated
More informationAE3610 Experiments in Fluid and Solid Mechanics TRANSIENT MEASUREMENTS OF HOOP STRESSES FOR A THIN-WALL PRESSURE VESSEL
Objective AE3610 Experiments in Fluid and Solid Mechanics TRANSIENT MEASUREMENTS OF OOP STRESSES FOR A TIN-WA PRESSURE VESSE This experiment will allow you to investigate hoop and axial stress/strain relations
More informationName (Print) ME Mechanics of Materials Exam # 1 Date: October 5, 2016 Time: 8:00 10:00 PM
Name (Print) (Last) (First) Instructions: ME 323 - Mechanics of Materials Exam # 1 Date: October 5, 2016 Time: 8:00 10:00 PM Circle your lecturer s name and your class meeting time. Gonzalez Krousgrill
More informationInternational ejournals
Available online at www.internationalejournals.com International ejournals ABSTRACT: STRUCTURAL AND THERMAL ANALYSIS OF CONDENSER BY USING FINITE ELEMENT ANALYSIS Sk. Abdul Mateen 1 and N. Amar Nageswara
More information[5] Stress and Strain
[5] Stress and Strain Page 1 of 34 [5] Stress and Strain [5.1] Internal Stress of Solids [5.2] Design of Simple Connections (will not be covered in class) [5.3] Deformation and Strain [5.4] Hooke s Law
More informationAtmospheric Entry. Technology, Mathematical Model and Simulation
Atmospheric Entry Technology, Mathematical Model and Simulation Julian Köllermeier RWTH Aachen, August 26th 2016 Outline 1. Introduction to Atmospheric Reentry 2. Rarefied Gases: From Science Fiction to
More informationThermo-Mechanical Analysis of Automotive Disc Brake Composite Rotor
International Journal of Engineering Science Invention ISSN (Online): 2319 6734, ISSN (Print): 2319 6726 Volume 6 Issue 5 May 2017 PP. 40-48 Thermo-Mechanical Analysis of Automotive Disc Brake Composite
More informationFinite Element Simulation of the Liquid Silicon Oriented Crystallization in a Graphite Mold
Finite Element Simulation of the Liquid Silicon Oriented Crystallization in a Graphite Mold Alexey I. Borovkov Vadim I. Suprun Computational Mechanics Laboratory, St. Petersburg State Technical University,
More informationIntroduction and Background
Introduction and Background Itasca Consulting Group, Inc. (Itasca) has been participating in the geomechanical design of the underground 118-Zone at the Capstone Minto Mine (Minto) in the Yukon, in northwestern
More informationKudryavtsev A. Yu., Zhelezov S.A., (Sarov Engineering Center) Polovin M.M., Litvinov M.S. (Sukhoi Civil Aircraft)
Numerical Simulations of High Temperature Jets from the Main Propulsion System and Auxiliary Power Unit Impinging Against a Construction of the Passenger Plane Kudryavtsev A. Yu., Zhelezov S.A., (Sarov
More informationMechanical Behavior of Composite Tapered Lamina
International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 10, Issue 8 (August 2014), PP.19-27 Mechanical Behavior of Composite Tapered Lamina
More informationInternational Journal of Scientific & Engineering Research, Volume 8, Issue 2, February-2017 ISSN
ISSN 2229-5518 916 Laser Damage Effect Studies with Hollow Metallic Targets Satyender Kumar, S Jain, K C Sati, S Goyal, R Malhotra, R Rajan, N R Das & A K Srivastava Laser Science & Technology Centre Metcalfe
More informationAnalysis of Catalyst Support Ring in a pressure vessel based on ASME Section VIII Division 2 using ANSYS software
IJSRD - International Journal for Scientific Research & Development Vol. 1, Issue 3, 2013 ISSN (online): 2321-0613 Analysis of Catalyst Support Ring in a pressure vessel based on ASME Section VIII Division
More informationAnalysis of Electro-thermal Stress and Strain in a Functionally Graded Metal Line under Direct Current Field
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 78-68,p-ISSN: -X, Volume, Issue Ver. II (Sep. - Oct. ), PP 7-8 www.iosrjournals.org Analysis of Electro-thermal Stress and Strain in
More informationA Numerical Study on Prediction of BFS in Composite Structures under Ballistic Impact
VOL. 1, 2015 ISSN 2394 3750 EISSN 2394 3769 SCIENCE & TECHNOLOGY A Numerical Study on Prediction of BFS in Composite Structures under Ballistic Impact Bandaru Aswani Kumar 1, Suhail Ahmad 2 1. Research
More informationDesign and Analysis of Adjustable Inside Diameter Mandrel for Induction Pipe Bender
International Journal of Engineering Trends and Technology (IJETT) Volume0Number - Apr 0 Design and Analysis of Adjustable Inside Diameter Mandrel for Induction Pipe Bender S.Nantha Gopan, M.Gowtham J.Kirubakaran
More information1 Static Plastic Behaviour of Beams
1 Static Plastic Behaviour of Beams 1.1 Introduction Many ductile materials which are used in engineering practice have a considerable reserve capacity beyond the initial yield condition. The uniaxial
More information7.3 Design of members subjected to combined forces
7.3 Design of members subjected to combined forces 7.3.1 General In the previous chapters of Draft IS: 800 LSM version, we have stipulated the codal provisions for determining the stress distribution in
More informationStructural Analysis of Warehouse Rack Construction for Heavy Loads
Vol:6, No:7, Structural Analysis of Warehouse Rack Construction for Heavy Loads C. Kozkurt, A. Fenercioglu, M. Soyaslan International Science Index, Civil and Environmental Engineering Vol:6, No:7, waset.org/publication/89
More information