To successfully square an HD series machine, you will need the following tools:
|
|
- Gerard Payne
- 5 years ago
- Views:
Transcription
1 To successfully square an HD series machine, you will need the following tools: Dial Indicator Machine Square Allen Keys Background: 1 st we align the square parallel to the Y-axis of travel so the X-axis is the only axis we will need to adjust. By lining the square up along the Y-axis, we can see and fix deviations that develop in the X-axis through manipulation or movement of the gantry. 1. Place the machine square on the process table of the machine. Orient the long side with the Y-axis and the short side with the X-axis. [1]
2 2. Using the appropriate collet, insert the dial indicator into the spindle and begin to move the spindle to the left side of the square. WARNING: It is recommended to unplug the spindle in case you accidentally depress the spindle on button. [2]
3 3. Using step mode, move the dial indicator to touch the left side of the square near the front. Rotate the spindle by hand to find the high point of the indicator. Zero the indicator or take note of the reading on the indicator. [3]
4 4. Now move the spindle down the Y-axis, along the edge of the machine square. You will notice that the dial indicator will move depending on whether or not the square is properly aligned. [4]
5 5. When the dial indicator is at the end of the edge of the square, you will need to move the square so that the indicator reads zero, or whatever reading was at the front. 6. Repeat this process going up and down the Y-axis as needed until both the front and rear of the square read the same on the dial indicator. Once this is done, you have now prepared the square for reading the alignment on the X-axis. 7. Align the spindle and dial indicator on the front edge of the square on the left hand side. Touch the edge with the dial indicator and zero the dial. Again rotate the spindle by hand to find the high point of the indicator. [5]
6 8. Move the indicator across the front of the square in the X-axis. When you get to the edge of the square, stop and note the reading on the indicator. This is the offset between the gantry uprights and therefore how out of square your machine is. [6]
7 9. To fix this offset, you will need to mechanically move the machine. To do so you must loosen a series of screws to correctly remedy the problem. 10. First remove the covers as indicated by your machine model: HD Mini: [7]
8 HD Series: [8]
9 11. You will need to loosen the screws holding the X-axis to these uprights in order to successfully square the machine. Please note the locations of these screws. HD Mini: [9]
10 HD Series: [10]
11 [11]
12 12. Loosen these screws, but keep at least one snug on the left side, this will act as a pivot point in squaring. 13. Now using your hand, push or pull the right side of the gantry to attempt to bring the dial indicator to its zero position. [12]
13 14. Once the zero has been found, tighten all the screws to correctly set the square of the machine. 15. Run the dial indicator back and forth across the front edge of the square to confirm. 16. You may need to repeat this procedure several times to bring the axis square around with a combination of pushing and pulling both sides to correctly square the machine. NOTE: Using a small rubber mallet to light tap the axis may help with the fine adjustment in the axis movement. This procedure may take several attempts to get it in place. 17. When finished, replace the side covers and make sure everything is tight. NOTE: Another way to check if the machine is square cut a large square and measure diagonally across the corners. They should match dimensionally. [13]
Squaring HD/HDS machine.
This document will detail how to square a Techno HD/HDS To preform this task you will need: -A set of metric allen wrentches. -A precision square. -A mallet. -A dial indicator. HTT00000000 Tel: 516/328-3970
More informationST - DS - Toolholders to the Spindle Centerline - Correction
LAST UPDATED: 11/28/2018 Page 1 of 9 pages Toolholders to the Spindle Centerline - Correction Page 2 of 9 pages This section tells you how to align the toolholders [1] to the spindle centerline [2]. 1
More informationproduct manual H-3220A Benkelman Beam
05.12 product manual H-3220A Benkelman Beam General The H-3220A Benkelman Beam Apparatus is a convenient and accurate device used for measuring the deflection of flexible pavements under moving wheel
More informationCASSINI CQR-800 OPERATING INSTRUCTIONS INTRODUCTION
HQR-800 CASSINI CQR-800 OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS ON YOUR PURCHASE OF THE CASSINI CQR-800 TELESCOPE. THIS TELESCOPE HAS BEEN PRODUCED TO PRECISE SPECIFICATIONS. PRIOR TO USING
More informationObserving Procedure for C11 GPS
Observing Procedure for C11 GPS By T. W. Fuller Preparation Customize observing list You can install a list of up to 25 custom objects in the telescope database ahead of time, so that you will have them
More information10-10 DIIAUS. Precision Reloading Scale
DIIAUS 10-10 Precision Reloading Scale 1010 grain capacity Micrometer paise Approach to weight Indication Tip proof scoop 1/10 grain accuracy Magnetic damping Dustproof cover/case No parallax errors Pour-easy
More informationFace Runout (Axial Eccentricity) of the Flywheel Housing
Page 1 of 5 7HVWLQJDQG$GMXVWLQJ &&DQG&2QKLJKZD\(QJLQHV 0HGLD1XPEHU5(15 3XEOLFDWLRQ'DWH 'DWH8SGDWHG Flywheel Housing - Inspect SMCS - 1157-040 Table 1 Tools Needed Part Number Part Name Quantity 8T-5096
More informationBallistic Pendulum. Equipment. Introduction. Setup
35 Ballistic Pendulum 35 - Page 1 of 5 Equipment Ballistic Pendulum 1 Rotary Motion Sensor PS-2120A 2 Photogate Head ME-9498A 1 Mounting Bracket ME-6821A 1 Large Table Clamp ME-9472 1 90 cm rod ME-8738
More informationC A S S I N I TRACKER
C A S S I N I TRACKER ASTRONOMICAL REFLECTOR T ELESCOPE SERIES #C-80080TR #C-1100102TR #C-1000120TR #C-1000120TREF #C-900135TR COSMO BRANDS INC. WWW.COSMOSOPTICS.COM 2 CASSINI REFLECTING TELESCOPE OPERATING
More informationASTRO-PHYSICS, INC. POLAR ALIGNMENT TELESCOPE
Polar Alignment Telescope ASTRO-PHYSICS, INC. POLAR ALIGNMENT TELESCOPE This polar axis telescope will help you align your mount with the Celestial Poles. When your mount is properly aligned, your telescope's
More informationTrunnion Hook-up (Tilt & Rotary = Full Axis)
. Trunnion Rotary Series March 2004 Trunnion Hook-up (Tilt & Rotary = Full Axis).......... Haas Automation Training MINIMUM MACHINE REQUIREMENTS TO USE THIS PROCEDURE: Haas CNC Mills with 5 axis capability.
More informationAutomatic Level Maintenance Manual SAL-XX W/ AIR DAMPENED COMPENSATOR
Automatic Level Maintenance Manual SAL-XX W/ AIR DAMPENED COMPENSATOR CST/Berger 2001 SAL 20/24/28/32 PAGE 1 REV. C 071803 Automatic Level Maintenance Manual User Calibration and Testing... 3 Circular
More informationTHE HAVERFORD UNIVERSITY S STRAWBRIDGE OBSERVATORY S OF THE 16 MEADE. A quick guide to using the 16 Meade Schmidt-Cassegrain Telescope
THE S OF THE 16 MEADE HAVERFORD UNIVERSITY S STRAWBRIDGE OBSERVATORY A quick guide to using the 16 Meade Schmidt-Cassegrain Telescope First draft: Scott Engle, Fall 2010; Update: Steve Boughn, Fall 2012
More informationASTRO-PHYSICS, INC. POLAR ALIGNMENT TELESCOPE (PASILL2)
OBJECTIVE LENS ASTRO-PHYSICS, INC. POLAR ALIGNMENT TELESCOPE (PASILL2) This model shipped from January 2001 through July 2002. It fits all 400, 600, 600E, 800, 900 and 1200 models (except the original
More informationCASSINI CQR-120 OPERATING INSTRUCTIONS
CASSINI CQR-120 OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS ON YOUR PURCHASE OF THE CASSINI CQR-120 TELESCOPE. THIS TELESCOPE HAS BEEN PRODUCED TO PRECISE SPECIFICATIONS. PRIOR TO USING YOUR NEW
More informationRIGHT-ANGLE POLAR ALIGNMENT SCOPE (RAPAS) INSTRUCTIONS
RIGHT-ANGLE POLAR ALIGNMENT SCOPE (RAPAS) INSTRUCTIONS Congratulations on your receipt of our new polar alignment scope and your new-found freedom from neck strain. The Astro-Physics Right-Angle Polar
More informationB Left-hand case side (x1) F
MD693/ HD-1688 WOODEN RADIO-CONTROLLED GRANDFATHER CLOCK WITH WESTMINSTER CHIMES INSTRUCTIONS PLEASE READ ALL THE INSTRUCTIONS CAREFULLY BEFORE YOU SET YOUR CLOCK GOING AND ENSURE YOU KEEP HOLD OF THESE
More informationConservation of Energy
rev 05/2018 Conservation of Energy Equipment Qty Item Part Number 1 Mini Launcher ME-6800 1 Metal Sphere Projectile 1 and 2 Meter Sticks 1 Large Metal Rod ME-8741 1 Small Metal Rod ME-8736 1 Support Base
More informationSCHIEBER TELESCOPES. Unique, High-Quality Telescopes
SCHIEBER TELESCOPES Unique, High-Quality Telescopes 3.5 Refractor Astrophotography Bundle - Strike 90 PLUS Telescope Assembly Instructions and Digital Eyepiece Camera Instructions. (1) telescope assembly
More informationRST INSTRUMENTS LTD.
RST INSTRUMENTS LTD. RST Tape Extensometer Instruction Manual Copyright Ltd. All Rights Reserved. Ltd. Kingston St., Maple Ridge, B.C. Canada VX Z Tel: () - Fax: () - Email: info@rstinstruments.com Website:
More informationRECON. How to Setup the Telescope to Observe. This guide will show you how to setup your telescope for observing. Written By: Brittany McCrigler
RECON How to Setup the Telescope to Observe This guide will show you how to setup your telescope for observing. Written By: Brittany McCrigler 2017 recon.dozuki.com Page 1 of 30 INTRODUCTION This guide
More informationService Information Letter SIL # 017
Service Information Letter SIL # 017 Trunnion Adjustment - Double Barrels Only Equipment: Double Barrels With Sloped Trunnions Date Issued: 9-24-03 Additional Reference: SIL # 016 Revised: Revision #:
More informationThermodynamics. We can summarize the four laws of thermodynamics as follows:
Thermodynamics Objective: To investigate the zeroth and first laws of thermodynamics. To calculate properties such as specific heat. To investigate the ideal gas law. To become familiar with basic P-V
More informationObservatory 8 inch Telescopes: Tips, Tools & Quick Fixes
Observatory 8 inch Telescopes: Tips, Tools & Quick Fixes Rhiannon Griffin August 7, 2014 1 Tools Needed Allen wrenches for set screws, 2 sizes For collimating: Phillips head screwdriver & slotted screwdriver
More informationMotion on a linear air track
Motion on a linear air track Introduction During the early part of the 17 th century, Galileo experimentally examined the concept of acceleration. One of his goals was to learn more about freely falling
More informationElectric Field Mapping
Electric Field Mapping Equipment: mapping board, U-probe, 5 resistive boards, templates, 4 long leads, Phywe 07035.00 voltmeter, DC wall voltage output, 3 pieces of paper Precautions 1. Before turning
More informationElectric Field Mapping
Electric Field Mapping Equipment: mapping board, U-probe, 5 resistive boards, templates, knob adjustable DC voltmeter, 4 long leads, 16 V DC for wall strip, 8 1/2 X 11 sheets of paper Reading: Topics of
More informationPOWER PUSHER Snowplow
May 15, 2013 Lit. No. 43682, Rev. 00 POWER PUSHER Snowplow 8' 72040; 10' 72045; Box Plow for Skid-Steer Loaders Owner's Manual and Installation Instructions Original Instructions CAUTION Read this manual
More informationElectric Field Mapping Lab 2. Precautions
TS 2-12-12 Electric Field Mapping Lab 2 1 Electric Field Mapping Lab 2 Equipment: mapping board, U-probe, resistive boards, templates, dc voltmeter (431B), 4 long leads, 16 V dc for wall strip Reading:
More informationGalileo Telescope Solar Viewer Joseph Hora, Elizabeth Hora 2017/09/18
Galileo Telescope Solar Viewer Joseph Hora, Elizabeth Hora 2017/09/18 17 7.75 5 2 1.5 3 2 1.5 Materials: (all dimensions in inches) 3x plywood sheet 17 x 7.75 x ½ 3x wood block cut from 2x4: 5 x 2 x 1.5
More information'-. MICROMEr II. The MICROMET8 II is shipped assembled except for the Filar Eyepiece, Micrometer Stage, and Standard Vise.
MICROMEr II '-. UNPACKING: Carefully unpack and check contents. If any components are missing or damaged, save the packing list and material, and advise the carrier and Buehler Ltd. of the discrepancy.
More informationThe force on a straight current-carrying conductor in a magnetic field is given by,
EXPERIMENT 12 Current Balance Introduction The current balance is used to measure the force of repulsion between identical, oppositely directed, currents in parallel conductors. In this experiment you
More informationImportant Instructions
Important Instructions Subject Use With Cabinet Hardmount Trunnion Replacement Cabinet Hardmount 8-60 Pound Washer-Extractors and Kits F77000, F7700, F7700, F7700, F7700, F7700, F9P and F9P WARNING This
More informationTelescope. 1. Read these instructions carefully and familiarise yourself with the procedure before assembling the unit.
Telescope a Simple assembly instructions- Please keep for future reference IMPORTANT 1. Read these instructions carefully and familiarise yourself with the procedure before assembling the unit. 2. Check
More informationMust Read Before Installation TadPoleTM Safety and Warnings
Must Read Before Installation TadPoleTM Safety and Warnings The recommendations, requirements, rules, and instructions of your Vehicle's Roof-Top Rack System should ALWAYS be followed. The TadPole TM,
More informationC A S S I N I. MODEL : C EQ3 900mm X 135mm COSMO BRANDS INC.
C A S S I N I MODEL : C-900135EQ3 900mm X 135mm COSMO BRANDS INC. WWW.COSMOSOPTICS.COM 2 C A S S I N I C-900135EQ3 TELESCOPE OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS ON YOUR PURCHASE OF THE
More informationCoulomb s Law. Coloumb s law Appratus Assembly
Coulomb s Law Objectives To demonstrate the veracity of Coulomb's Law. To do this you will show that the Electrostatic Force between two charged bodies is directly proportional to the product of their
More informationDouble-foliot Japanese Clock
How to Assemble and Use the Supplement Double-foliot Japanese Parts in the Kit Assembly time: Approx. 1 hour and 30 minutes Second for speed adjustment hand receiver Front plate Pillar for the foliots
More informationE Service E-Series Padlock seires PadlockManual No. Part No. Part No. Part
E-Series Padlock E Service seires Manual Padlock 0 No. Part No. Part No. Part Padlock body Locking plate Ball bearing 0 Shackle Bumper 0 Socket head screw Mx0 Activator cam Identification plate Spring
More informationCAUTION: BEFORE YOU BEGIN, ALWAYS MAKE SURE THE WEAPON IS UNLOADED AND SAFE TO HANDLE.
CAUTION: BEFORE YOU BEGIN, ALWAYS MAKE SURE THE WEAPON IS UNLOADED AND SAFE TO HANDLE. ON Press either brightness button ( + or - ) to turn on the sight. The sight is also programmed to turn on when it
More informationPLOW MOUNT KIT FOR POLARIS RANGER P/N ASSEMBLY / OWNERS MANUAL
PLOW MOUNT KIT FOR POLARIS RANGER P/N 34-3010 ASSEMBLY / OWNERS MANUAL Application PLOW PUSH FRAME NO. 34-0000 or 34-0070 Before you begin, please read these instructions and check to be sure all parts
More informationOperating Instructions Validation Tool Kit, KT2 For use with USP Apparatus #1 & #2
Operating Instructions Validation Tool Kit, KT2 For use with USP Apparatus #1 & #2 P/N VALTOL-KT2 Revision 2.0 October 7, 2014 Prepared by: Quality Lab Accessories, LLC 100 Emlen Way, Suite 108 Telford,
More informationTHE LOSMANDY G-11 MOUNT
Checking the parts THE LOSMANDY G-11 MOUNT Depending on which accessories you ordered, your G-11 mount was shipped in four or more boxes. The contents of each box are as follows: Equatorial Mount Adjustable
More informationCircular Motion and Centripetal Force
[For International Campus Lab ONLY] Objective Measure the centripetal force with the radius, mass, and speed of a particle in uniform circular motion. Theory ----------------------------- Reference --------------------------
More informationWHEN BRIGHTNESS COUNTS
WHEN BRIGHTNESS COUNTS CAUTION: BEFORE INSTALLATION, CONFIRM THAT FIREARM IS UNLOADED AND IN SAFE OPERABLE CONDITION. MOUNTING (Handgun Slide/Plate mount) To mount the TRU TEC MICRO on the slide of an
More informationKalinka Optics Warehouse User Manual Kobra AK Side Mount Red Dot Sight Manual
Kalinka Optics Warehouse User Manual www.kalinkaoptics.com Kobra AK Side Mount Red Dot Sight Manual CONTENTS 1. Introduction... 4 2. Purpose... 4 3. Specifications... 4 4. Components and Equipment Provided...
More informationproduct manual H-4204 Proving Ring Penetrometer
05.09 product manual H-4204 Proving Ring Penetrometer nnmm Handle Proving Ring Extension Rod Coupler Penetration Rod Cone Figure #1 General Information The Proving Ring Penetrometer is a cone type of penetrometer
More informationOwner's Manual NSL100B BUILDERS LEVEL NSL500B TRANSIT LEVEL
Owner's Manual NSL100B BUILDERS LEVEL NSL500B TRANSIT LEVEL 1 1. CONTENTS 2. Nomenclature page 3 3. Care and Maintenance page 4 4. Using your Instrument 4.1 Setting up your Instrument page 5 4.2 Stadia
More informationSHARK Snow Plow. 52 (132 cm) / 60 (152 cm) Complete system blade INSTRUCTIONS / ESTABLISHMENT
SHARK Snow Plow 52 (132 cm) / 60 (152 cm) Complete system blade INSTRUCTIONS / ESTABLISHMENT OPERATING INSTRUCTIONS Congratulations! You ve just purchased the most durable plow system in the industry.
More informationOPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS for the Perkin Elmer Model 650-10S Fluorescence Spectrophotometer Re: Operating Instructions PE 650 2 The following flow diagram should help to guide you through the steps necessary
More informationAppendix 2: Disassembling and Assembling the Telescopes and the Celestron Equatorial Mounts
Appendix 2: Disassembling and Assembling the Telescopes and the Celestron Equatorial Mounts Disassembling (classroom) 1. The mount must be locked with the telescope situated horizontally. Note the telescope
More informationPlease complete this form and enclose it with your carefully packed watch for repair. Add a check for postage and handling.
Watch Repair Please complete this form and enclose it with your carefully packed watch for repair. Add a check for postage and handling. ($12.95 within the U.S. and $38.00 outside of the U.S.) Name: Address:
More informationCourse: Technology II Training course topic: Metrology
Department of machining, process planning and metrology ver.2017-01 Following problems and tasks will be solved during the first two weeks of the training courses of Technology II. Detailed information
More informationDual Use: Shooting Tactical / Hunting US Patent 8,166,696 US Patent 7,937,879. Radius Bar. Reticle Focus. Elevation Adjustment Knob
The Vortex Viper PST tm Riflescope Specifically designed for the tactical, law enforcement and committed precision shooting communities, the Viper PST TM series of riflescopes offer the highest levels
More informationNewton s Second Law Knex cars. Vanderbilt Student Volunteers for Science VINSE/VSVS Rural Training Presentation
Newton s Second Law Knex cars Vanderbilt Student Volunteers for Science 2018-2019 VINSE/VSVS Rural Training Presentation Important!!! Please use this resource to reinforce your understanding of the lesson!
More information10 - Celestron Telescope II: Operation
10 - Celestron Telescope II: Operation Purpose: Gain more experience setting up a 6 Celestron telescope, familiarize yourself with the software interface, and acquire an image with the CCD camera. Due:
More informationAlphaLab Gaussmeter Model VGM -- Instructions
AlphaLab Gaussmeter Model VGM -- Instructions Power: As shipped, a standard 9 volt battery is installed. Battery life is about 10 hours (25 ma drain; 6.5 volt dropout). Low battery appears when about one
More informationINSTALLATION INSTRUCTIONS ATV Plow Blade Part Number: (50 ), (54 ), or (60 ) Application: All Terrain Vehicles
INSTALLATION INSTRUCTIONS ATV Plow Blade Part Number: 78950 (50 ), 78954 (54 ), or 78960 (60 ) Application: All Terrain Vehicles Your safety, and the safety of others, is very important. To help you make
More informationWARNING. INJURY HAZARD Failure to observe these instructions could lead to severe injury or death.
INSTALLATION INSTRUCTIONS Kawasaki Mule Plow Mounting Kit WARN Part Number: 71983 Application: Kawasaki Mule 2002-2006 Your safety, and the safety of others, is very important. To help you make informed
More informationReference number: Worksheet/Receipt. Owners name: - Telephone: Description of item(s) received, including accessories:
Worksheet/Receipt Owners name: - Address: n/a Telephone: n/a Description of item(s) received, including accessories: Jaguar E-Type Smiths car clock marked CE 1114/00 (negative earth). Work required based
More informationFOCUS 30/FOCUS 35 Field Calibration with Survey Pro Field Software
GeoInstruments Application Note June 25th, 2015 FOCUS 30/FOCUS 35 Field Calibration with Survey Pro Field Software Summary: This support note outlines the procedure which should be followed to calibrate
More information50 Gordon Drive, Rockland, Maine sherplows.com. STORM BOXX Snowplow. 10' and 12' Box Plow for Backhoe Loaders
Fisher Engineering 50 Gordon Drive, Rockland, Maine 04841-2139 www.fi sherplows.com 83180, 83185 May 15, 2013 Lit. No. 43687, Rev. 00 STORM BOXX Snowplow 10' and 12' Box Plow for Backhoe Loaders Owner's
More informationCoulomb s Law PHYS 296
Coulomb s Law PHYS 296 Your name Lab section PRE-LAB QUIZZES 1. What is the purpose of this lab? 2. Two conducting hollow balls of diameter 3.75 cm are both initially charged by a bias voltage of +5000
More informationGravity: How fast do objects fall? Teacher Advanced Version (Grade Level: 8 12)
Gravity: How fast do objects fall? Teacher Advanced Version (Grade Level: 8 12) *** Experiment with Audacity and Excel to be sure you know how to do what s needed for the lab*** Kinematics is the study
More informationT1 and E1 Feature Cards
CHAPTER 3 This chapter provides procedures for installing and removing the T1 and E1 feature cards and includes the following sections: Overview, page 3-1 Online Installation and Removal of the T1 or E1
More informationCOLLIMATING THE ASTROTRAC POLAR SCOPE By Darryl Hedges
COLLIMATING THE ASTROTRAC POLAR SCOPE By Darryl Hedges Why Collimate The AstroTrac Polar Scope? The word collimate means to accurately align, typically used when talking about light. The purpose of collimating
More informationHB Coupled Pendulums Lab Coupled Pendulums
HB 04-19-00 Coupled Pendulums Lab 1 1 Coupled Pendulums Equipment Rotary Motion sensors mounted on a horizontal rod, vertical rods to hold horizontal rod, bench clamps to hold the vertical rods, rod clamps
More informationINSTALLATION INSTRUCTIONS ATV SNOW PLOW Mounting Kit: PN Application: HONDA 400
INSTALLATION INSTRUCTIONS ATV SNOW PLOW Mounting Kit: PN 37851 Application: HONDA 400 Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have
More informationThe Vortex Razor HD Gen II-E 1 6x24 Riflescope
The Vortex Razor HD Gen II-E 1 6x24 Riflescope At Vortex Optics, the need for high-performance, precision optics is the driving force behind all that we do. We carefully built the Razor HD Gen II-E riflescope
More informationPARTS CATALOGUE / TECHNICAL GUIDE Cal. 4F32A, 8F32A Cal. 8F33A, 8F35A
PARTS CATALOGUE / TECHNICAL GUIDE Cal. 4F32A, 8F32A Cal. 8F33A, 8F35A PARTS CA TALOGUE / TECHNICAL GUIDE (p. 1 22) CATÁLOGO DE PARTES / GUÍA TÉCNICA (p. 23 44) [SPECIFICATIONS] (Revised: 2008 Apr.) Item
More informationConnect the Vernier spectrometer to your lap top computer and power the spectrometer if necessary. Start LoggerPro on your computer.
Connect the Vernier spectrometer to your lap top computer and power the spectrometer if necessary. Start LoggerPro on your computer. The screen shown in Fig. 1 may be displayed. If status line displays
More informationIssue date: 30. Apr TECHNICAL GUIDE PARTS CATALOGUE. Cal.NH25/26 AUTOMATIC MECHANICAL. SII Products
Issue date: 30. Apr. 2008 TECHNICAL GUIDE & PARTS CATALOGUE AUTOMATIC MECHANICAL [SPECIFICATION] Item PARTS CATALOGUE / TECHNICAL GUIDE Cal. No. NH25 NH26 Movement Movement size Time indication Basic function
More informationPlatinum Series. 6-30x56 Front Focal Plane Scope. with Patent Pending DEKA MIL Reticle. DEKA MIL reticle for unsurpassed accuracy at long range
6-30x56 Front Focal Plane Scope with Patent Pending DEKA MIL Reticle DEKA MIL reticle for unsurpassed accuracy at long range PA6-30X56FFP-DEKA-AMS Platinum Series 1. Turn the Power Ring to a high setting,
More informationSurface Zeta Potential Cell (ZEN1020)
Surface Zeta Potential Cell (ZEN1020) MAN0483 Issue 1.0 September 2011 English Copyright Malvern Instruments Ltd. 2011 Malvern Instruments makes every effort to ensure that this document is correct. However,
More informationROTARY CONTROLS. Rotary controls 1. GENERAL FEATURES 2. POSITION INDICATORS
ROTARY CONTROLS 1. GENERAL FEATURES ELESA-CLAYTON rotary controls are used to set and regulating a wide variety of machine functions. The device consists of: - a handwheel/knob, to manoeuvre the control
More informationv ox Motion in Two Dimensions (Projectile Motion)
Motion in Two Dimensions (Projectile Motion) In this experiment we will study motion in two-dimensions. An object which has motion in both the X and Y direction has a two dimensional motion. We will first
More informationFOR POLARIS ATV s P/N ASSEMBLY / OWNERS MANUAL
MID-MOUNT KIT FOR POLARIS ATV s P/N 15-3591 ASSEMBLY / OWNERS MANUAL Application PLOW PUSH FRAME NO. 15-0070, 33-0000 or 33-0070 Before you begin, please read these instructions and check to be sure all
More informationRP-300 TELESCOPE Instruction Manual
RP-300 TELESCOPE Instruction Manual 2070 5th Avenue Ronkonkoma, NY 11779 Phone: 631-963-5000 Fax: 631-427-6749 For information, call toll-free: 1-800-967-8427 info@carson.com / sales@carson.com / www.carson.com
More informationPotential and Kinetic Energy
Lab VII Potential and Kinetic Energy 1 Introduction This is a lab about the interplay between kinetic and potential energy. While we can calculate forces and accelerations of an object as it moves along
More informationCardiff Astronomical Observatory
Rules for using the Cardiff Astronomical Observatory at Dyffryn Gardens Contents Menu Rules for accessing Dyffryn Gardens and using the Observatory 2 Access to Dyffryn Gardens out of hours 2 Access to
More informationCollimation with a Takahashi collimating scope
Collimation with a Takahashi collimating scope These instructions describe how you can adjust your Alluna Ritchey-Chrétien telescope to perfection in just a few steps and just a few minutes using a Takahashi
More informationHey, that wasn t so hard. INSTRUCTION MANUAL AND WARRANTY
Hey, that wasn t so hard. INSTRUCTION MANUAL AND WARRANTY THANK YOU FOR CHOOSING AN INVICTA TIMEPIECE Long ago, we set out to continue Invicta s original 1837 mission to offer magnificent Swiss timepieces
More informationZ650HR SERIES MANUAL ZOOM STEREO MICROSCOPE. 73 Mall Drive, Commack, NY (P) (F)
Z650HR SERIES ZOOM STEREO MICROSCOPE MANUAL 73 Mall Drive, Commack, NY 11725 631-543-2000 (P) 631-589-6975 (F) www.unitronusa.com info@unitronusa.com CONTENTS SAFETY NOTES... 3 CARE AND MAINTENANCE...
More informationShaft Alignment and Couplings
Industrial Maintenance Shaft Alignment and Couplings Course Sample 49138-3C Order no.: 49138-3C First Edition Revision level: 03/2018 By the staff of Festo Didactic Festo Didactic Ltée/Ltd, Quebec, Canada
More informationWinding the mainspring, adjusting the hand, day/date is done by the below procedure. day adjustment hand adjustment date adjustment
method Winding the mainspring, adjusting the hand, day/date is done by the below procedure. day adjustment hand adjustment date adjustment (1) Winding the mainspring Automatic winding watch can also be
More informationIntroduction to Fluid Mechanics - Su First experiment: Flow through a Venturi
530.327 - Introduction to Fluid Mechanics - Su First experiment: Flow through a Venturi 1 Background and objectives. In this experiment, we will study the flow through a Venturi section using both flow
More informationHaas trunnions have more than one configuration. Thus, to make a program for the trunnion, you must know these facts:
Haas Technical Documentation Trunnion Information Scan code to get the latest version of this document Translation Available Trunnion Features Haas trunnions have more than one configuration. Thus, to
More informationINSTALLATION INSTRUCTIONS ATV SNOW PLOW Mounting Kit: PN Application: HONDA MODELS: 450S AND 450ES
INSTALLATION INSTRUCTIONS ATV SNOW PLOW Mounting Kit: PN 37852 Application: HONDA MODELS: 450S AND 450ES Your safety, and the safety of others, is very important. To help you make informed decisions about
More informationDual Red or Green Electronic Dot Sight Instruction Manual
Dual Red or Green Electronic Dot Sight Instruction Manual 2007 VisionPlus INTRODUCTION: Congratulations on your purchase of a VisionPlus Dual Red/Green Electronic Dot Sight. This is a quality product engineered
More informationElectrostatics: Coulomb's Law
Electrostatics: Coulomb's Law Objective: To learn how excess charge is created and transferred. To measure the electrostatic force between two objects as a function of their electrical charges and their
More informationGY 301: Geomorphology Lab 5: Total Station Mapping Project
Introduction This is the capstone lab project for GY 301. With the assistance of your team member (4 people per team), you will use the Total Station to survey a topographic map of the campus area (see
More informationINSTALLING TRAK SPORT TIRE CHAINS ON 20 MODEL 3 TIRES
INSTALLING TRAK SPORT TIRE CHAINS ON 20 MODEL 3 TIRES 2018 TESLA, INC. All rights reserved. All information in this document and all MODEL 3 software is subject to copyright and other intellectual property
More informationPLOW MOUNT KIT FOR YAMAHA VIKING P/N ASSEMBLY / OWNERS MANUAL. Application PLOW PUSH FRAME NO or
PLOW MOUNT KIT FOR YAMAHA VIKING P/N 34-5020 ASSEMBLY / OWNERS MANUAL Application PLOW PUSH FRAME NO. 34-0000 or 34-0070 Before you begin, please read these instructions and check to be sure all parts
More informationMonolayer Grazing Angle Specular Reflectance Accessory User Manual
Monolayer Grazing Angle Specular Reflectance Accessory User Manual 2I-19650-7 Monolayer Grazing Angle Specular Reflectance Accessory User Manual 2I-19650-7 User Manual Monolayer Grazing Angle Specular
More informationBATTERY REPLACEMENT MANUAL FOR CAL. 4F (LADIES ) / 8F (GENT S) SERIES WATCHES
BATTERY REPLACEMENT MANUAL FOR CAL. 4F (LADIES ) / 8F (GENT S) SERIES WATCHES NOTE: When replacing the battery for Cal. 4F and Cal. 8F Series watches, please be sure to use and batteries having a seal-type
More informationMees Observatory telescope checklist
Mees Observatory telescope checklist Last revised 30 April 2003 DMW Startup 1. Turn on all circuit breakers in the breaker box by the front door. (Those with tape on them are always on; don t turn them
More informationExperiment 19: The Current Balance
Experiment 19: The Current Balance Figure 19.1: Current Balance Arrangement for Varying Current or Length From Left to Right: Power Supply, Current Balance Assembly, Ammeter (20A DCA scale, 20A jack).
More information14010 Force Table Student Guide
Recommended Accessories: Scissors Level (to adjust the legs of the apparatus) Blank paper or graph paper Pencil Ruler Protractor Calculator Optional Accessories: Paper clips 14010 Force Table Student Guide
More informationHD Gen II 1 6x24 Riflescope. The Vortex Razor
Razor HD Gen II 1-6x24 Specifications Waterproof Yes Fogproof Argon Gas Tube Diameter 30 mm Length 10.0 Inches (254 mm) Mounting Length 6.0 Inches (162.6 mm) Weight 18.4 Ounces (521.6 g) Eye Relief 4.0
More informationRP-200 TELESCOPE Instruction Manual
2070 5th Avenue Ronkonkoma, NY 11779 Phone: 631-963-5000 Fax: 631-427-6749 For information, call toll-free: 1-800-967-8427 info@carson.com / sales@carson.com / www.carson.com RP-200 TELESCOPE Instruction
More information