Location-Dependent Impacts of Resource Inertia on Power System Oscillations
|
|
- Maurice Glenn
- 5 years ago
- Views:
Transcription
1 Proceedings of the 51 st Hawaii International Conference on System Sciences 2018 Location-Dependent Impacts of Resource Inertia on Power System Oscillations Ti Xu, Wonhyeok Jang, Thomas Overbye Department of Electrical and Computer Engineering Texas A&M University, College Station, TX, USA {txu, wjang777, Abstract Inertial responses are seen by the system as the injection or withdrawal of electrical energy, corresponding to a change of frequency. The inertia of a machine primarily contributes to the power system transient stability. Oscillations are always present in the bulk power system due to the electromechanical nature of the grid. Poorly damped oscillations may cause system instability. Thus, this paper aims to study inertia s impacts on system primary frequency response, in particular on system oscillation modes. Both transient stability simulations and modal analysis are performed to provide insights into the extent to which inertia and its location influence the system oscillation behavior. Simulation results using both a small-scale test system and a large-scale synthetic network dynamic model are presented to verify the locational impacts of resource inertia. 1. Introduction Primary frequency response (PFR) is largely determined by generators inertia and governor responses. As the power system generation side is changing to include more renewable resources connected by power electronics and more light-weight generators, the system is shifting towards less inertia. With lower grid inertia, small events may result in larger frequency excursions than before. Reports [1], [2] by the North American Electric Reliability Corporation (NERC) indicated a declining frequency response in both the Eastern Interconnection (EI) and the Electric Reliability Council of Texas (ERCOT) footprints. In references [3], [4], authors performed time-domain simulations to analyze the inertia s impacts on transient stability. Previous work [5] investigated the locationdependent impacts of inertia on power system primary frequency response. Post-disturbance system oscillation modes are of interest for evaluating the system transient stability, in addition to minimum/maximum rate of change of frequency (RoCoF) and minimum/maximum frequency during the first several seconds after disturbances. URI: ISBN: (CC BY-NC-ND 4.0) Power systems can experience a wide range of oscillations, ranging from high-frequency switching transients to sustained low frequency (< 2 Hz) inter-area oscillations affecting an entire interconnect. A system oscillation mode is a natural property of electromechanical system, and characterized by its oscillating frequency, damping performance and effect area [6]. An oscillation can be either undamped, positively damped (decaying with time) or negatively damped (growing with time). However, there are few works studying the impacts of resource inertia on system oscillation frequency and damping behavior. Modal analysis was used in [7] for analysing phase angle-based power system inter-area oscillation. Works [8], [9] applied modal analysis for studies on inertia in consideration of deep solar energy penetration. Authors also extracted modal information to investigate damping of inter-area oscillations in large interconnected power systems [10]. As such, we aim to investigate how system oscillation modes vary with inertia being reduced and how this oscillation mode variation is related to inertia s location. This paper first uses a straight-forward smallscale test system for illustration. To obtain realistic simulation results, this paper also performs studies on a large-scale synthetic network model [11] [14]. A set of scenarios with various inertia at different sites are constructed to show, for a power system, what aspects the inertia and its location have effects on. The test system in some cases experiences natural oscillations, and forced ones in other cases. In this work, we focus on local plant oscillations. The major effect area of the local plant oscillation is localized to a small set of generators close to each other and lines connecting them [15]. Specifically, we perform time-domain simulations and modal analysis for inertia studies. In this paper, four more sections come as follows. Section II provides some background knowledges on transient stability formulation and modal analysis techniques. In Section III, a simple example is applied to illustrate inertia s locational impacts. Simulations results on a large-scale synthetic system model with varying regional inertia are presented in Section IV. Conclusion and future work direction are provided in Section V. Page 2710
2 2. Background In this section, we give an overview of transient stability formulation and the role of inertia in the formation. We also briefly discuss about the basic idea of all techniques to extract power system modal information The Machine Swing Equation in System Transient Stability Formulation To determine response of the system over a time period of seconds to perhaps a minute after a contingency, a set of differential and algebraic equations is formulated in a general form as follows: ẋ = f(x, y, u) (1) 0 = g(x, y) (2) where x is the vector of the state variables, y is the vector of the algebraic variables, and u is the input vector. Those equations are integrated using either explicit or implicit methods [16]. Through network impedance, machine characteristics, load characteristics and transient stability controls all play their parts in system dynamic responses. For each synchronous machine i, there are two differential equations in (1), known as the swing equation: The damping ratio is then calculated as 100σ k, σ 2 k +ωk 2 where σ k and ω k = 2πf k are the real and imaginary parts of the eigenvalue λ k associated with each mode k. f k is mode k oscillation frequency. For each mode, unique relationships among the four parameters are: a) when damping of a mode increases, the real part σ k changes from positive to negative, and vice versa; b) when frequency of a mode increases, the imaginary part ω k increases, and vice versa. In this paper, the variable projection method (VPM) is used to determine the characteristic modes observed from time series analysis [19]. We use oscillation frequency and damping ratio as metrics to analyze the locational impacts of inertia on system oscillation modes. 3. Preliminary Studies In this section, we apply a simple, straightforward 138-kV test system with three generators for illustrating resource inertia s locational impacts on system oscillation and damping behavior. δ i = ω i ω B = ω i (3) 2H i ω s dω i dt = 2H i d ω i = T Mi T Ei D i ω i (4) ω s dt T Mi and T Ei are mechanical and electrical torques, between which the difference results in the change of rotor angular velocity ω i and position δ i. H i is the normalized inertia value H i = Ji(ω B) 2 2S B, with a MVA base S B and rotor s actual moment of inertia J i. Given a fixed difference between a generator s mechanical input and electrical output, rotor accelerates or decelerates faster if inertia is lower, and vice versa Modal Analysis Post-contingency system responses may experience oscillations that either damp out, sustain or grow. Those oscillatory responses can be measured and analyzed to extract modal information of the system. Idea of modal analysis is to approximate a signal z(t) by the sum of exponential functions ẑ(t) = k a k exp(λ k t) that could preserve the original signal s properties such as oscillation frequency and damping. ẑ(t) is typically obtained by solving the following minimization problem for a set of sampling points [17], [18]. min a k,λ k t T (z(t) ẑ(t)) 2 (5) Fig. 1: Oneline diagram of a three-bus test system 3.1. Simulation Setup and Results The three-bus test system as shown in Fig.1 supplies a load connected to bus 3. Each bus is connected to a generator. A balanced 3-phase fault is applied to bus 1 at 1 second and cleared 0.01 seconds later. We reduce the inertia of gen 3 by amounts from 0 MWs to 300 MWs in increment of 100 MWs (Case 1) 1. Fig.2 shows the rotor speeds of generators at buses 1 and 3 in Case 1. For comparisons, Case 2 reduces the inertia of gen 1 by amounts from 0 MWs to 300 MWs in increment of 100 MWs. The rotor speeds of generators at buses 1 and 3 in Case 2 are displayed in Fig Inertia is often expressed in unit of second on the machine MVA base that varies by generator. Thus, we express inertia in MWs ( = MVA base inertia in s) for convenient comparisons among different generators. For instance, given a base of 100 MVA, an inertia of 1 s is equivalent to an inertia of 100 MWs. Page 2711
3 Fig. 2: Simulation results of a bus fault event on the three-bus test system with varying inertia of gen 3 and frequency at bus 1. Those results indicate that local inertia has large effects on local oscillation modes. We also note that the inertia reduction at each generator also impacts its nearby generator s oscillation. In Fig.2 (Fig.3), inertia reduction at bus 3 (1) slightly increases the oscillation magnitude of gen 1 (3). Furthermore, with 300-MWs inertia reduction in Case 2, more than one oscillation mode are observed for the gen 3 rotor speed. To provide insights into changes in oscillation modes, Table 1 displays the modal analysis results on the three-bus test system with varying inertia. The original system oscillates at 2.1 Hz. We observe one slow mode (2.106 Hz with damping ratio of %) and one fast mode (2.122 Hz with damping ratio of %). Inertia reduction in Case 1 slightly changes the slow oscillation mode, and significantly speed up and amplify the fast oscillation. In contrast, the slow oscillation mode oscillates faster with a higher magnitude and the fast one changes little, as inertia in bus 1 is reduced. Furthermore, in Case 2, 300-MWs inertia reduction at Gen 1 results in unstable system frequency with a negative damping ratio. This mode at Hz is also observed at Gen 3 rotor speed, as shown in the bottom figure of Fig.3. Table 1: Modal analysis results on the three-bus test system with varying inertia Case 1 2 Mode Slow Fast Inertia Ch- Freq Damping Freq Damping ange(mws) (Hz) Ratio (%) (Hz) Ratio (%) Fig. 3: Simulation results of a bus fault event on the three-bus test system with varying inertia of gen Discussion The inertia reduction at each generator significantly changes the local oscillation magnitude. In Case 1, the local oscillation magnitude at bus 3 becomes smaller first and then increases as the gen 3 s inertia is reduced. Meanwhile, the local oscillation frequency at bus 3 has similar behavior. Rather, gen 1 s inertia reduction in Case 2 always enlarges the local oscillation magnitude Both cases demonstrate that inertia contributes to the system oscillation modes. The locational dependence of resource inertia s impacts on power system oscillation modes is also observed in this small-test case system. In the remaining of this paper, we focus our simulations studies on system dynamic responses using a synthetic large-scale test system. 4. Illustrative Studies using Synthetic Network Models To provide insightful and realistic results, we perform more simulations using synthetic network models that are built by applying statistics summarized from Page 2712
4 actual system models and data available to public [11] [13]. Those synthetic models available at [14] are entirely fictitious, but are able to capture structural and functional features of actual power grids Simulation Setup This section adopts a 2000-bus synthetic network - ACTIVSg2k - on the Electric Reliability Council of Texas (ERCOT) footprint, as shown in Fig.4. Given a load level set to 67 GW, the system has a total inertia of 390 GWs from online generation units. This test system has eight areas. Table. 2 summarizes the total resource inertia of online units in each area. We consider three regions (R1 with COAST, R2 with SCENT and SOUTH, and R3 with NORTH, NCENT and FWEST) in the following case studies. R2 and R3 have similar total regional inertia, which is lower than that of R1. the original system. Cases (b) and (c) reduce remote inertia in one region by 50 GWs. Nearby inertia that does not include that of generators in O is reduced by 50 GWs in Case (d). Inertia of generators in O is decreased by 50 % in Case (e). Table 3: Case Set I Detail Case I.1 I.2 Event Type three-phase bus fault line outage Event Location R1 R3 Oscillation Origin R3 R1 Local Inertia O 1 O 2 R3 R1 Nearby Inertia (O 1 excluded) (O 2 excluded) Remote Inertia R1 & R2 R2 & R3 Fig. 4: Eight areas in the ACTIVSg2k model Table 2: Total resource inertia of online generation units of each area in the synthetic network dynamic model Area Name COAST EAST FWEST WEST Inertia (MWs) Area Name NCENT NORTH SCENT SOUTH Inertia (MWs) Case Study Set I Table.3 provides details on Case Set I. Each subset in Set I has a local oscillation caused by a few generators, defined as a set O. Set I aims to study how local oscillations are impacted by the amount and location of inertia of generator set O (local inertia), nearby generators in the same region as O (nearby inertia) and ones far away from O (remote inertia). In both Case Sets I.1 and I.2, Case (a) performs studies using Fig. 5: Simulated bus frequencies in Case Set I.1 Case Set I.1 considers a three-bus fault in R1. As shown in Fig.5(a), the original system experiences a 0.66-Hz local oscillation of the generator set O 1 in R3. Fig.5(b) and (c) present bus frequencies with a 50-GWs regional inertia reduction in R1 and R2, respectively. Results in Fig.5(d) are obtained after R3 regional inertia of online generators (O 1 excluded) is reduced by 50 GWs, while those in Fig.5(e) are obtained after only inertia of generator set O 1 is reduced by 50%. Oscillation frequency and damping ratio are also displayed in Fig.5(a)-(e). Nearby and remote inertia reduction slows down this oscillation and improves its damping performance. However, impacts of both nearby and remote inertia reduction on this Page 2713
5 local oscillation are trivial. In contrast, the local inertia reduction significantly worsens this local oscillation. Due to decreased local inertia, this mode oscillates faster and its damping ratio becomes negative, which causes an unstable system condition. In Case Set I.2, after a transmission line in R3 is open, this test system experiences a 1.24-Hz local oscillation caused by the generator set O 2 in R1. Similar to case design in Set I.1, Case I.2.b and Case I.2.c study the impact of remote inertia, by running simulation with a 50-GWs regional inertia reduction in R2 and R3, respectively. Case I.2.d reduces the R1 regional inertia of online generators (O 2 excluded) by 50 GWs, and Case I.2.e decreases inertia only of generators in O 2 by 50%. Comparing with Case Set I.1, we observe very different results in Case Set I.2. The well-damped oscillations in Fig.6(e) shows that local inertia reduction significantly improves local oscillation. Nearby and remote inertia reduction significantly worsen this oscillation. In particular, oscillations in Cases I.2.b- I.2.d are growing with negative damping ratios. This is because the generators near the local oscillation origin are less capable to prevent the oscillation from spreading over the network and disturbing the network as their inertia is reduced. depending on the current system operating condition Case Study Set II To further study the effects of the inertia and its location on system oscillation modes, we perform sensitivity studies with a forced oscillation to trigger system oscillations. In Case Set II, we subject this system to a 1-Hz forced oscillation for a generator in R1. For each region, we proportionally reduce the inertia of each unit in that region such that the reduction in the regional total inertia varies from 0 MWs to 50,000 MWs in increment of 5,000 MWs. For comparisons, we perform the same simulations using the synthetic model with the reduced total inertia of the system varying from 0 MWs to 50,000 MWs in increment of 5,000 MWs (reference case 0). Fig. 7: Modal analysis results in Case Set II Fig. 6: Simulated bus frequencies in Case Set I.2 Both case sets indicate an important role of local inertia in the local oscillations. Local inertia reduction may largely deteriorate or alleviate oscillations. Decreased nearby and remote inertia typically worsen local oscillations, and its severeness varies by location. Furthermore, the locational variation in the impacts of local inertia, nearby inertia and remote inertia is also Fig.7 displays the change of oscillation frequency and damping ratio with respect to the reduction in regional inertia. We note that the inertia reduction in different regions have distinguishable impacts on the system modes. In particular, inertia reduction in R2 causes the 2-Hz mode moving from poorly damping to negatively damping. We note discontinuity in oscillation mode change as the inertia reduces. Some modes always exist from 0 GWs all the way up to 50 GWs of inertia reduction, while other modes only show up in a particular period of inertia reduction. This is because the VPM is a measurement-based approach and hence the modes with a trivial magnitude are not observable for a certain period of inertia reduction. For instance, when the regional inertia in R1 is reduced by more than 15 GWs, the 2.1-Hz mode vanishes. Page 2714
6 In summary, we carried out several studies to reveal the sensitivity of modal analysis results with respect to the inertia reduction in different regions. Simulation results demonstrate that the impacts of inertia on system oscillation behavior vary by inertia s location. 5. Conclusion In this paper, both a small-scale test system and a large-scale synthetic dynamic model were used to study the inertia s impacts on system oscillation modes. Natural oscillation modes were triggered by either a three-phase bus fault, a transmission line outage or a forced oscillation. We performed time-domain simulations and modal analysis, and observed the locational dependence of impacts of inertia. As such, inertia should be an important factor to be taken into consideration during activities related to power system transient stability. Replacement of conventional units by light- or zeroinertia units will be considered to study the locational impacts of inertia. Both frequency/rocof ranges and oscillation modes should be considered as essential metrics for assessment of system dynamic responses. Given the location-dependent values and impacts of inertia, it is also of interest to construct a comprehensive market simulation tool with integration of transient stability constraints. We will report these studies in future work. Acknowledgment The authors would like to thank the U.S. Department of Energy Consortium for Electric Reliability Technology Solutions (CERTS) for their support in this research. References [1] NERC, Balancing and frequency control, January [Online]. Available: http: // %20Frequency\%20Control\% pdf. [2], Frequency response initiative report, October [Online]. Available: Report Master w-appendices.pdf. [3] D. Gautam, V. Vittal, and T. Harbour, Impact of increased penetration of dfig-based wind turbine generators on transient and small signal stability of power systems, IEEE Transactions on Power Systems, vol. 24, no. 3, pp , Aug [4] J. McLoughlin, Y. Mishra, and G. Ledwich, Estimating the impact of reduced inertia on frequency stability due to largescale wind penetration in australian electricity network, in Power Engineering Conference (AUPEC), 2014 Australasian Universities, Sept 2014, pp [5] T. Xu, A. B. Birchfield, K. S. Shetye, and T. J. Overbye, Creation of synthetic electric grid models for transient stability studies, accepted by 2017 IREP Symposium Bulk Power System Dynamics and Control, [6] NERC, Reliability guideline - forced oscillation monitoring & mitigation, June [Online]. Available: Guideline\ -\ Forced\ Oscillations\ -\ 2017.pdf [7] T. Xia, Y. Zhang, L. Chen, Z. Yuan, P. N. Markham, Y. Ye, and Y. Liu, Phase angle-based power system inter-area oscillation detection and modal analysis, European Transactions on Electrical Power, vol. 21, no. 4, pp , [8] S. Eftekharnejad, V. Vittal, G. T. Heydt, B. Keel, and J. Loehr, Impact of increased penetration of photovoltaic generation on power systems, IEEE Transactions on Power Systems, vol. 28, no. 2, pp , May [9], Small signal stability assessment of power systems with increased penetration of photovoltaic generation: A case study, IEEE Transactions on Sustainable Energy, vol. 4, no. 4, pp , Oct [10] R. Witzmann, Damping of interarea oscillations in large interconnected power systems, in International Conference on Power Systems Transients, [11] A. B. Birchfield, K. M. Gegner, T. Xu, K. S. Shetye, and T. J. Overbye, Statistical considerations in the creation of realistic synthetic power grids for geomagnetic disturbance studies, IEEE Transactions on Power Systems, vol. 32, no. 2, pp , March [12] A. B. Birchfield, T. Xu, K. M. Gegner, K. S. Shetye, and T. J. Overbye, Grid structural characteristics as validation criteria for synthetic networks, IEEE Transactions on Power Systems, vol. PP, no. 99, pp. 1 1, [13] T. Xu, A. B. Birchfield, K. M. Gegner, K. S. Shetye, and T. J. Overbye, Application of large-scale synthetic power system models for energy economic studies, in Hawaii International Conference on System Sciences (HICSS-50), Jan 2017, pp [14] Electric Grid Test Case Repository - Synthetic Electric Grid Cases. [Online]. Available: [15] G. Rogers, Power System Oscillation. New York, NY, USA: 2000, [16] J. D. Glover, M. S. Sarma, and T. Overbye, Power System Analysis and Design, 5th ed. Cengage Learning, [17] P. Kundur, Power System Stability and Control. New York, NY: McGraw-Hill, [18] P. Sauer and M. Pai, Power System Dynamics and Stability. Champagin, IL: Stripes Publishing L.L.C., [19] J. G. A. Borden, B.C. Lesieutre, Power system modal analysis tool developed for industry use, in Proc North American Power Symposium, Sept Ti Xu (S 12) received the B.S. degree in 2011 from Tsinghua University, Beijing, P.R.C.. He received the M.S. and Ph.D. degrees from the University of Illinois at Urbana-Champaign, Urbana, IL, USA, in 2014 and He is currently a postdoctoral researcher in Electrical and Computer Engineering at the Texas A&M University, College Station, TX, USA. Wonhyeok Jang (S 10) received the B.S. and M.S. degrees in Electrical Engineering from Sungkyunkwan University, Seoul, Korea. He received the Ph.D. degree in 2017 from the University of Illinois at Urbana-Champaign, Urbana, IL, USA. He is currently a postdoctoral researcher in Electrical and Computer Engineering at the Texas A&M University, College Station, TX, USA. Thomas J. Overbye (S 87 M 92 SM 96 F 05) received the B.S., M.S., and Ph.D. degrees in electrical engineering from the University of Wisconsin-Madison, Madison, WI, USA. He is currently the TEES Distinguished Research Professor in Electrical and Computer Engineering at the Texas A&M University, College Station, TX, USA. Page 2715
Investigation of Inertia s Locational Impacts on Primary Frequency Response using Large-scale Synthetic Network Models
Investigation of Inertia s Locational Impacts on Primary Frequency Response using Large-scale Synthetic Network Models Ti Xu, Student Member, IEEE, Wonhyeok Jang, Student Member, IEEE, and Thomas J. Overbye,
Predicting, controlling and damping inter-area mode oscillations in Power Systems including Wind Parks
3rd IASME/WSEAS Int. Conf. on Energy & Environment, University of Cambridge, UK, February 3-5, 008 Predicting, controlling and damping inter-area mode oscillations in Power Systems including Wind Parks
Minimax Approximation Synthesis in PSS Design by Embedding
Minimax Approximation Synthesis in PSS Design by Embedding Gravitational Search Algorithm Dr. Akash Saxena Department of Electrical Engineering Swami Keshvanand Institute of Technology Jaipur, India Power
Power System Stability and Control. Dr. B. Kalyan Kumar, Department of Electrical Engineering, Indian Institute of Technology Madras, Chennai, India
Power System Stability and Control Dr. B. Kalyan Kumar, Department of Electrical Engineering, Indian Institute of Technology Madras, Chennai, India Contents Chapter 1 Introduction to Power System Stability
Impact of Photovoltaic Generation On The Power System Stability
Impact of Photovoltaic Generation On The Power System Stability Eng. Abdelmoezz Ahmed Eid Dept. of Electrical Engineering Al-Azhar University Cairo, Egypt engabdelmoezz@gmail.com Dr. Tarek Mahmoud Dept.
11.1 Power System Stability Overview
11.1 Power System Stability Overview This introductory section provides a general description of the power system stability phenomena including fundamental concepts, classification, and definition of associated
ECEN 667 Power System Stability Lecture 20: Oscillations, Small Signal Stability Analysis
ECEN 667 Power System Stability Lecture 20: Oscillations, Small Signal Stability Analysis Prof. Tom Overbye Dept. of Electrical and Computer Engineering Texas A&M University, overbye@tamu.edu 1 Announcements
Transient Stability Analysis of Single Machine Infinite Bus System by Numerical Methods
International Journal of Electrical and Electronics Research ISSN 348-6988 (online) Vol., Issue 3, pp: (58-66), Month: July - September 04, Available at: www.researchpublish.com Transient Stability Analysis
Small Signal Stability Analysis of Power System with Increased Penetration of PV Generation
Kalpa Publications in Engineering Volume, 207, Pages 200 207 ICRISET207. International Conference on Research and Innovations in Science, Engineering &Technology. Selected Papers in Engineering Small Signal
Real-Life Observations of Power System Dynamic Phenomena Some Interesting Aspects
Real-Life Observations of Power System Dynamic Phenomena Some Interesting Aspects A.M.Kulkarni Department of Electrical Engineering, IIT Bombay and Visiting Professor, University of Manitoba The Indian
ECE 585 Power System Stability
Homework 1, Due on January 29 ECE 585 Power System Stability Consider the power system below. The network frequency is 60 Hz. At the pre-fault steady state (a) the power generated by the machine is 400
FLEXIBLE ac transmission system (FACTS) devices give
694 IEEE TRANSACTIONS ON POWER DELIVERY, VOL. 19, NO. 2, APRIL 2004 A Newton-Type Current Injection Model of UPFC for Studying Low-Frequency Oscillations Kwang M. Son, Member, IEEE, and Robert H. Lasseter,
Generalized Injection Shift Factors and Application to Estimation of Power Flow Transients
Generalized Injection Shift Factors and Application to Estimation of Power Flow Transients Yu Christine Chen, Alejandro D. Domínguez-García, and Peter W. Sauer Department of Electrical and Computer Engineering
ECE 422/522 Power System Operations & Planning/Power Systems Analysis II : 7 - Transient Stability
ECE 4/5 Power System Operations & Planning/Power Systems Analysis II : 7 - Transient Stability Spring 014 Instructor: Kai Sun 1 Transient Stability The ability of the power system to maintain synchronism
DYNAMIC RESPONSE OF A GROUP OF SYNCHRONOUS GENERATORS FOLLOWING DISTURBANCES IN DISTRIBUTION GRID
Engineering Review Vol. 36 Issue 2 8-86 206. 8 DYNAMIC RESPONSE OF A GROUP OF SYNCHRONOUS GENERATORS FOLLOWING DISTURBANCES IN DISTRIBUTION GRID Samir Avdaković * Alija Jusić 2 BiH Electrical Utility Company
GMD Impacts on Power System Voltage Stability. Komal S. Shetye Research Engineer University of Illinois at Urbana-Champaign
1 GMD Impacts on Power System Voltage Stability Komal S. Shetye Research Engineer University of Illinois at Urbana-Champaign shetye1@illinois.edu 2 Overview of GMDs and GICs GMD: Geomagnetic Disturbances
Impact of Model Detail of Synchronous Machines on Real-time Transient Stability Assessment
2013 IREP Symposium-Bulk Power System Dynamics and Control IX (IREP), August 25-30, 2013, Rethymnon, Greece Impact of Model Detail of Synchronous Machines on Real-time Transient Stability Assessment Tilman
ANALYSIS OF SUBSYNCHRONOUS RESONANCE EFFECT IN SERIES COMPENSATED LINE WITH BOOSTER TRANSFORMER
ANALYSIS OF SUBSYNCHRONOUS RESONANCE EFFECT IN SERIES COMPENSATED LINE WITH BOOSTER TRANSFORMER G.V.RAJASEKHAR, 2 GVSSNS SARMA,2 Department of Electrical Engineering, Aurora Engineering College, Hyderabad,
Effect of Inertia Constant on Generator Frequency and Rotor Angle
Engineering and Applied Sciences 2018; 3(1): 6-11 http://www.sciencepublishinggroup.com/j/eas doi: 10.11648/j.eas.20180301.12 ISSN: 2575-2022 (Print); ISSN: 2575-1468 (Online) Effect of Inertia Constant
POWER SYSTEM STABILITY
LESSON SUMMARY-1:- POWER SYSTEM STABILITY 1. Introduction 2. Classification of Power System Stability 3. Dynamic Equation of Synchronous Machine Power system stability involves the study of the dynamics
Control Lyapunov Functions for Controllable Series Devices
IEEE TRANSACTIONS ON POWER SYSTEMS, VOL. 16, NO. 4, NOVEMBER 2001 689 Control Lyapunov Functions for Controllable Series Devices Mehrdad Ghandhari, Member, IEEE, Göran Andersson, Fellow, IEEE, and Ian
Transient Stability Assessment of Synchronous Generator in Power System with High-Penetration Photovoltaics (Part 2)
Journal of Mechanics Engineering and Automation 5 (2015) 401-406 doi: 10.17265/2159-5275/2015.07.003 D DAVID PUBLISHING Transient Stability Assessment of Synchronous Generator in Power System with High-Penetration
SCHOOL OF ELECTRICAL, MECHANICAL AND MECHATRONIC SYSTEMS. Transient Stability LECTURE NOTES SPRING SEMESTER, 2008
SCHOOL OF ELECTRICAL, MECHANICAL AND MECHATRONIC SYSTEMS LECTURE NOTES Transient Stability SPRING SEMESTER, 008 October 7, 008 Transient Stability Transient stability refers to the ability of a synchronous
Comparing the Impact of HEMP Electric Field Waveforms on a Synthetic Grid
Comparing the Impact of HEMP Electric Field Waveforms on a Synthetic Grid Raymund Lee and Thomas J. Overbye Department of Electrical and Computer Engineering Texas A&M University College Station, TX, USA
ECEN 667 Power System Stability Lecture 15: PIDs, Governors, Transient Stability Solutions
ECEN 667 Power System Stability Lecture 15: PIDs, Governors, Transient Stability Solutions Prof. Tom Overbye Dept. of Electrical and Computer Engineering Texas A&M University, overbye@tamu.edu 1 Announcements
Oscillation energy based sensitivity analysis and control for multi-mode oscillation systems
Oscillation energy based sensitivity analysis and control for multi-mode oscillation systems Horacio Silva-Saravia, Yajun Wang, Héctor Pulgar-Painemal, Kevin Tomsovic Department of Electrical Engineering
Chapter 9: Transient Stability
Chapter 9: Transient Stability 9.1 Introduction The first electric power system was a dc system built by Edison in 1882. The subsequent power systems that were constructed in the late 19 th century were
COMPARISON OF DAMPING PERFORMANCE OF CONVENTIONAL AND NEURO FUZZY BASED POWER SYSTEM STABILIZERS APPLIED IN MULTI MACHINE POWER SYSTEMS
Journal of ELECTRICAL ENGINEERING, VOL. 64, NO. 6, 2013, 366 370 COMPARISON OF DAMPING PERFORMANCE OF CONVENTIONAL AND NEURO FUZZY BASED POWER SYSTEM STABILIZERS APPLIED IN MULTI MACHINE POWER SYSTEMS
A Power System Dynamic Simulation Program Using MATLAB/ Simulink
A Power System Dynamic Simulation Program Using MATLAB/ Simulink Linash P. Kunjumuhammed Post doctoral fellow, Department of Electrical and Electronic Engineering, Imperial College London, United Kingdom
CURENT Course Power System Coherency and Model Reduction
CURENT Course Power System Coherency and Model Reduction Prof. Joe H. Chow Rensselaer Polytechnic Institute ECSE Department November 1, 2017 Slow Coherency A large power system usually consists of tightly
Reliability of Bulk Power Systems (cont d)
Reliability of Bulk Power Systems (cont d) Important requirements of a reliable electric power service Voltage and frequency must be held within close tolerances Synchronous generators must be kept running
Transient Stability Analysis with PowerWorld Simulator
Transient Stability Analysis with PowerWorld Simulator T1: Transient Stability Overview, Models and Relationships 2001 South First Street Champaign, Illinois 61820 +1 (217) 384.6330 support@powerworld.com
IEEE PES Task Force on Benchmark Systems for Stability Controls
IEEE PES Task Force on Benchmark Systems for Stability Controls Ian Hiskens November 9, 3 Abstract This report summarizes a study of an IEEE -generator, 39-bus system. Three types of analysis were performed:
DESIGN OF POWER SYSTEM STABILIZER USING FUZZY BASED SLIDING MODE CONTROL TECHNIQUE
DESIGN OF POWER SYSTEM STABILIZER USING FUZZY BASED SLIDING MODE CONTROL TECHNIQUE LATHA.R Department of Instrumentation and Control Systems Engineering, PSG College of Technology, Coimbatore, 641004,
EVALUATION OF THE IMPACT OF POWER SECTOR REFORM ON THE NIGERIA POWER SYSTEM TRANSIENT STABILITY
EVALUATION OF THE IMPACT OF POWER SECTOR REFORM ON THE NIGERIA POWER SYSTEM TRANSIENT STABILITY F. I. Izuegbunam * Department of Electrical & Electronic Engineering, Federal University of Technology, Imo
Performance of Flocking-Based Control Schemes in Smart Grid Applications
Performance of Flocking-Based Control Schemes in Smart Grid Applications Abdallah K. Farraj Eman M. Hammad Jin Wei Deepa Kundur Karen L. Butler-Purry Department of Electrical and Computer Engineering,
Analysis of Coupling Dynamics for Power Systems with Iterative Discrete Decision Making Architectures
Analysis of Coupling Dynamics for Power Systems with Iterative Discrete Decision Making Architectures Zhixin Miao Department of Electrical Engineering, University of South Florida, Tampa FL USA 3362. Email:
1. Introduction. Keywords Transient Stability Analysis, Power System, Swing Equation, Three-Phase Fault, Fault Clearing Time
Energy and Power 17, 7(1): -36 DOI: 1.593/j.ep.1771.3 Numerical Simulations for Transient Stability Analysis of Two-Machine Power System Considering Three-Phase Fault under Different Fault Clearing Times
Examples of Applications of Potential Functions in Problem Solving (Web Appendix to the Paper)
Examples of Applications of otential Functions in roblem Solving (Web Appendix to the aper) Ali Mehrizi-Sani and Reza Iravani May 5, 2010 1 Introduction otential functions may be exploited to formulate
Cascading Outages in Power Systems. Rui Yao
Cascading Outages in Power Systems Rui Yao yaorui.thu@gmail.com Outline Understanding cascading outages Characteristics of cascading outages Mitigation of cascading outages Understanding cascading outages
A Decoupling Based Direct Method for Power System Transient Stability Analysis
A Decoupling Based Direct Method for Power System Transient Stability Analysis Bin Wang, Kai Sun Electrical Engineering and Computer Science University of Tennessee, Knoxville, TN USA bwang13@utk.edu,
WIDE AREA CONTROL THROUGH AGGREGATION OF POWER SYSTEMS
WIDE AREA CONTROL THROUGH AGGREGATION OF POWER SYSTEMS Arash Vahidnia B.Sc, M.Sc in Electrical Engineering A Thesis submitted in partial fulfilment of the requirements for the degree of Doctor of Philosophy
Eigenvalue Analysis of Subsynchronous Resonance Study in Series Compensated Wind Farm
e-issn: 2349-9745 p-issn: 2393-8161 Scientific Journal Impact Factor (SJIF): 1.711 International Journal of Modern Trends in Engineering and Research www.ijmter.com Eigenvalue Analysis of Subsynchronous
IJSER. 1. Introduction
International Journal of Scientific & Engineering Research, Volume 7, Issue 5, May-2016 1543 Transient Stability Analysis of Generation and Transmission system of a thermal power plant of Pakistan. Izhar
Parameter Sensitivity Analysis for Sub-Synchronous Oscillations in Wind-Integrated Power Systems
LOGO Parameter Sensitivity Analysis for Sub-Synchronous Oscillations in Wind-Integrated Power Systems Meng Wu 1, Rongfu Sun 2, Lin Cheng 3, and Le Xie 1 1: Texas A&M University, 2: China Jibei Power Grid,
Document Version Publisher s PDF, also known as Version of Record (includes final page, issue and volume numbers)
Impacts of distributed generation penetration levels on power system transient stability Reza, M.; Schavemaker, P.H.; Slootweg, J.G.; Kling, W.L.; Sluis, van der, L. Published in: Proc. IEEE PES General
MITIGATION OF POWER SYSTEM SMALL SIGNAL OSCILLATION USING POSICAST CONTROLLER AND EVOLUTIONARY PROGRAMMING
Journal of Engineering Science and Technology Special Issue on Applied Engineering and Sciences, October (2014) 39-50 School of Engineering, Taylor s University MITIGATION OF POWER SYSTEM SMALL SIGNAL
Critical clearing time evaluation of Nigerian 330kV transmission system
American Journal of Electrical Power and Energy Systems 2013; 2(6): 123-128 Published online October 20, 2013 (http://www.sciencepublishinggroup.com/j/epes) doi: 10.11648/j.epes.20130206.11 Critical clearing
Comparative Study of Synchronous Machine, Model 1.0 and Model 1.1 in Transient Stability Studies with and without PSS
Comparative Study of Synchronous Machine, Model 1.0 and Model 1.1 in Transient Stability Studies with and without PSS Abhijit N Morab, Abhishek P Jinde, Jayakrishna Narra, Omkar Kokane Guide: Kiran R Patil
Research Paper ANALYSIS OF POWER SYSTEM STABILITY FOR MULTIMACHINE SYSTEM D. Sabapathi a and Dr. R. Anita b
Research Paper ANALYSIS OF POWER SYSTEM STABILITY FOR MULTIMACHINE SYSTEM D. Sabapathi a and Dr. R. Anita b Address for Correspondence a Research Scholar, Department of Electrical & Electronics Engineering,
Power System Stability GENERATOR CONTROL AND PROTECTION
Power System Stability Outline Basis for Steady-State Stability Transient Stability Effect of Excitation System on Stability Small Signal Stability Power System Stabilizers Speed Based Integral of Accelerating
POWER SYSTEM DYNAMIC SECURITY ASSESSMENT CLASSICAL TO MODERN APPROACH
Abstract POWER SYSTEM DYNAMIC SECURITY ASSESSMENT CLASSICAL TO MODERN APPROACH A.H.M.A.Rahim S.K.Chakravarthy Department of Electrical Engineering K.F. University of Petroleum and Minerals Dhahran. Dynamic
ECEN 667 Power System Stability Lecture 25: FFT, Energy Methods
ECEN 667 Power System Stability Lecture 5: FFT, Energy Methods Prof. Tom Overbye Dept. of Electrical and Computer Engineering Texas A&M University, overbye@tamu.edu 1 Announcements Read Chapter 9 Final
Micro-grid to System Synchronization Based on Pre-Insertion Impedance Method (Version 1.0) By Peter Zhou University of Alberta Jan 30 th, 2015
Micro-grid to System Synchronization Based on Pre-Insertion Impedance Method (Version 1.0) By Peter Zhou University of Alberta Jan 30 th, 2015 Outline 1. What is Synchronization? 2. Synchronization Concerns?
Power Grid Partitioning: Static and Dynamic Approaches
Power Grid Partitioning: Static and Dynamic Approaches Miao Zhang, Zhixin Miao, Lingling Fan Department of Electrical Engineering University of South Florida Tampa FL 3320 miaozhang@mail.usf.edu zmiao,
Robust Tuning of Power System Stabilizers Using Coefficient Diagram Method
International Journal of Electrical Engineering. ISSN 0974-2158 Volume 7, Number 2 (2014), pp. 257-270 International Research Publication House http://www.irphouse.com Robust Tuning of Power System Stabilizers
KINGS COLLEGE OF ENGINEERING Punalkulam
KINGS COLLEGE OF ENGINEERING Punalkulam 613 303 DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING POWER SYSTEM ANALYSIS QUESTION BANK UNIT I THE POWER SYSTEM AN OVERVIEW AND MODELLING PART A (TWO MARK
TCSC-Based Wide Area Damping Controller (WADC) for Inter-area oscillations in Saudi Power Network
-Based Wide Area Damping Controller (WADC) for Inter-area oscillations in Saudi Power Network Saleh M. Bamasak (1)(2) *, Yusuf A. Al-Turki (1), Sreerama Kumar R. (1) & Malek M. Al-Hajji (2) 1 King Abdulaziz
SYNCHRONOUS GENERATOR s ROTOR INVESTIGATION OF A HYBRID POWER SYSTEM INCLUDING A.G.
Proc. of the 5th WSEAS/IASME Int. Conf. on Electric Power Systems, High Voltages, Electric Machines, Tenerife, Spain, December 16-18, 25 (pp59-514) SYNCHRONOUS GENERATOR s ROTOR INVESTIGATION OF A HYBRID
ECEN 667 Power System Stability Lecture 23:Measurement Based Modal Analysis, FFT
ECEN 667 Power System Stability Lecture 23:Measurement Based Modal Analysis, FFT Prof. Tom Overbye Dept. of Electrical and Computer Engineering Texas A&M University, overbye@tamu.edu 1 Announcements Read
Sensitivity-Based Line Outage Angle Factors
Sensitivity-Based Line Outage Angle Factors Kai E. Van Horn, Alejandro D. Domínguez-García, and Peter W. Sauer Department of Electrical and Computer Engineering University of Illinois at Urbana-Champaign
Design Principles of Wind Turbine Inertia Emulators for Autonomous Systems
Preprints of the 19th World Congress The International Federation of Automatic Control Design Principles of Wind Turbine Inertia Emulators for Autonomous Systems Lampros N. Papangelis*. Costas D. Vournas*
Trajectory Sensitivity Analysis as a Means of Performing Dynamic Load Sensitivity Studies in Power System Planning
21, rue d Artois, F-75008 PARIS CIGRE US National Committee http : //www.cigre.org 2014 Grid of the Future Symposium Trajectory Sensitivity Analysis as a Means of Performing Dynamic Load Sensitivity Studies
Mitigating Subsynchronous resonance torques using dynamic braking resistor S. Helmy and Amged S. El-Wakeel M. Abdel Rahman and M. A. L.
Proceedings of the 14 th International Middle East Power Systems Conference (MEPCON 1), Cairo University, Egypt, December 19-21, 21, Paper ID 192. Mitigating Subsynchronous resonance torques using dynamic
Power System Model Reduction. Fall 2014 CURENT Course
Power System Model Reduction Fall 04 CURENT Course October 9, 04 Joe H. Chow Rensselaer Polytechnic Institute, Troy, New York, USA www.ecse.rpi.edu/homepages/chowj Model Reduction of Large Power Systems.
POWER systems are increasingly operated closer to their
1438 IEEE TRANSACTIONS ON POWER SYSTEMS, VOL. 19, NO. 3, AUGUST 2004 Scaling of Normal Form Analysis Coefficients Under Coordinate Change Ian Dobson, Senior Member, IEEE, and Emilio Barocio, Member, IEEE
Adaptive under frequency load shedding using synchrophasor measurement
Adaptive under load shedding using synchrophasor measurement Abstract - The imbalance between the generation and the demand is the major factor that causes instability in a power system. Conventional Under
Renewables and the Smart Grid. Trip Doggett President & CEO Electric Reliability Council of Texas
Renewables and the Smart Grid Trip Doggett President & CEO Electric Reliability Council of Texas North American Interconnected Grids The ERCOT Region is one of 3 North American grid interconnections. The
POWER SYSTEM STABILIZER CONTROL FOR WIND POWER TO ENHANCE POWER SYSTEM STABILITY
PHYSCON 2011, León, Spain, September, 5 September, 8 2011 POWER SYSTEM STABILIZER CONTROL FOR WIND POWER TO ENHANCE POWER SYSTEM STABILITY José Luis Domínguez-García Electrical Engineering Area IREC Spain
Variable Projection Method for Power System Modal Identification
IEEE TRANSACTIONS ON POWER SYSTEMS, VOL. 29, NO. 6, NOVEMBER 2014 2613 Variable Projection Method for Power System Modal Identification Alexander R. Borden, Student Member, IEEE, and Bernard C. Lesieutre,
Coordinated Variable Structure Switching in Smart Power Systems: Attacks and Mitigation
Coordinated Variable Structure Switching in Smart Power Systems: Attacks and Mitigation Shan Liu, Deepa Kundur, Takis Zourntos and Karen Butler-Purry Department of Electrical and Computer Engineering Texas
Minimization of Shaft Torsional Oscillations by Fuzzy Controlled Braking Resistor Considering Communication Delay
Proceedings of the 7th WSEAS International Conference on Power Systems, Beijing, China, September 15-17, 2007 174 Minimization of Shaft Torsional Oscillations by Fuzzy Controlled Braking Resistor Considering
CHAPTER 3 SYSTEM MODELLING
32 CHAPTER 3 SYSTEM MODELLING 3.1 INTRODUCTION Models for power system components have to be selected according to the purpose of the system study, and hence, one must be aware of what models in terms
Torques 1.0 Two torques We have written the swing equation where speed is in rad/sec as:
Torques 1.0 Two torques We have written the swing equation where speed is in rad/sec as: 2H Re ( t) T au T mu T eu (1) and when speed is in per-unit as 2H u ( t) Tau Tmu Teu (2) We note that in both cases
Performance Evaluation of DFIG to Changes in Network Frequency
019 CIENCELINE Journal of World s Electrical Engineering and Technology J. World. Elect. Eng. Tech. 8(1): 01-06, 019 JWEET Performance Evaluation of DFIG to Changes in Network Frequency Ramin Tayebi-Derazkolaie
APPLICATIONS OF CONTROLLABLE SERIES CAPACITORS FOR DAMPING OF POWER SWINGS *
APPLICATIONS OF CONTROLLABLE SERIES CAPACITORS FOR DAPING OF POWER SWINGS *. Noroozian P. Halvarsson Reactive Power Compensation Division ABB Power Systems S-7 64 Västerås, Sweden Abstract This paper examines
Centralized Supplementary Controller to Stabilize an Islanded AC Microgrid
Centralized Supplementary Controller to Stabilize an Islanded AC Microgrid ESNRajuP Research Scholar, Electrical Engineering IIT Indore Indore, India Email:pesnraju88@gmail.com Trapti Jain Assistant Professor,
Real-Time Wide-Area Dynamic Monitoring Using Characteristic Ellipsoid Method
Real-Time Wide-Area Dynamic Monitoring Using Characteristic Ellipsoid Method Funded by DOE through CERTS Presented by Dr. Yuri V. Makarov on behalf of the project team NASPI Meeting Orlando, FL February
QUESTION BANK ENGINEERS ACADEMY. Power Systems Power System Stability 1
ower ystems ower ystem tability QUETION BANK. A cylindrical rotor generator delivers 0.5 pu power in the steady-state to an infinite bus through a transmission line of reactance 0.5 pu. The generator no-load
A STATIC AND DYNAMIC TECHNIQUE CONTINGENCY RANKING ANALYSIS IN VOLTAGE STABILITY ASSESSMENT
A STATIC AND DYNAMIC TECHNIQUE CONTINGENCY RANKING ANALYSIS IN VOLTAGE STABILITY ASSESSMENT Muhammad Nizam Engineering Faculty Sebelas Maret University (Ph.D Student of Electrical, Electronic and System
Determination of stability limits - Angle stability -
Workshop Increased Utilisation of the Nordic Power Transmission System NTNU/SINTEF 30-31. October 2002 Determination of stability limits Magni Þ. Pálsson AS Trondheim 1 Contents Definitions and descriptions
Effects of Various Uncertainty Sources on Automatic Generation Control Systems
Effects of Various Uncertainty Sources on Automatic Generation Control Systems D. Apostolopoulou, Y. C. Chen, J. Zhang, A. D. Domínguez-García, and P. W. Sauer University of Illinois at Urbana-Champaign
Stability studies of different AC collection network topologies in wind farms connected to weak grids
Stability studies of different A collection network topologies in wind farms connected to weak grids K Givaki, D hen, O Anaya-Lara Department of Electronic and Electrical Engineering, University of Strathclyde,
CHAPTER 2 MODELING OF POWER SYSTEM
38 CHAPTER 2 MODELING OF POWER SYSTEM 2.1 INTRODUCTION In the day to day scenario, power is an essential commodity to the human beings. The demand is more in developed countries and there is increase in
SUPPLEMENTARY INFORMATION
DOI: 1.138/NPHYS535 Spontaneous synchrony in power-grid networks Adilson E. Motter, Seth A. Myers, Marian Anghel and Takashi Nishikawa Supplementary Sections S1. Power-grid data. The data required for
IEEE PES Task Force on Benchmark Systems for Stability Controls
IEEE PES Task Force on Benchmark Systems for Stability Controls Report on Benchmark #2 The Brazilian 7 Bus (Equivalent Model) Version 1 - October 23 rd, 214 Fernando J. de Marco, Leonardo Lima and Nelson
B.E. / B.Tech. Degree Examination, April / May 2010 Sixth Semester. Electrical and Electronics Engineering. EE 1352 Power System Analysis
B.E. / B.Tech. Degree Examination, April / May 2010 Sixth Semester Electrical and Electronics Engineering EE 1352 Power System Analysis (Regulation 2008) Time: Three hours Answer all questions Part A (10
Aldi Mucka Tonin Dodani Marjela Qemali Rajmonda Bualoti Polytechnic University of Tirana, Faculty of Electric Engineering, Republic of Albania
8. СОВЕТУВАЊЕ Охрид, 22 24 септември Aldi Mucka Tonin Dodani Marjela Qemali Rajmonda Bualoti Polytechnic University of Tirana, Faculty of Electric Engineering, Republic of Albania REHABILITATIONS OF EXCITATION
Performance Of Power System Stabilizerusing Fuzzy Logic Controller
IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, Volume 9, Issue 3 Ver. I (May Jun. 2014), PP 42-49 Performance Of Power System Stabilizerusing Fuzzy
7. Transient stability
1 7. Transient stability In AC power system, each generator is to keep phase relationship according to the relevant power flow, i.e. for a certain reactance X, the both terminal voltages V1and V2, and
PMU-Based Power System Real-Time Stability Monitoring. Chen-Ching Liu Boeing Distinguished Professor Director, ESI Center
PMU-Based Power System Real-Time Stability Monitoring Chen-Ching Liu Boeing Distinguished Professor Director, ESI Center Dec. 2015 Real-Time Monitoring of System Dynamics EMS Real-Time Data Server Ethernet
Virtual Inertia: Current Trends and Future Directions
applied sciences Review Virtual Inertia: Current Trends and Future Directions Ujjwol Tamrakar 1, Dipesh Shrestha 1, Manisha Maharjan 1, Bishnu P. Bhattarai 2, Timothy M. Hansen 1 and Reinaldo Tonkoski
SSSC Modeling and Damping Controller Design for Damping Low Frequency Oscillations
SSSC Modeling and Damping Controller Design for Damping Low Frequency Oscillations Mohammed Osman Hassan, Ahmed Khaled Al-Haj Assistant Professor, Department of Electrical Engineering, Sudan University
On-Line TSA and Control at EMS Control Centers for Large Power Grids
On-Line TSA and Control at EMS Control Centers for Large Power Grids Dr. Hsiao-Dong Chiang (i) Prof. of School of Electrical and Computer Engineering, Cornell University, Ithaca, NY (ii) President of BSI,
Harmonic Modeling of Networks
Harmonic Modeling of Networks Thomas H. Ortmeyer ECE Dept. Clarkson University Potsdam, NY 13699-5720 M. Fayyaz Akram Dept. of Elec. Eng. Univ. of Engineering and Technology Lahore, Pakistan Takashi Hiyama
Automatic Generation Control. Meth Bandara and Hassan Oukacha
Automatic Generation Control Meth Bandara and Hassan Oukacha EE194 Advanced Controls Theory February 25, 2013 Outline Introduction System Modeling Single Generator AGC Going Forward Conclusion Introduction
Self-Tuning Control for Synchronous Machine Stabilization
http://dx.doi.org/.5755/j.eee.2.4.2773 ELEKTRONIKA IR ELEKTROTECHNIKA, ISSN 392-25, VOL. 2, NO. 4, 25 Self-Tuning Control for Synchronous Machine Stabilization Jozef Ritonja Faculty of Electrical Engineering
Geometry-based Estimation of Stability Region for A Class of Structure Preserving Power Grids
1 Geometry-based Estimation of Stability Region for A Class of Structure Preserving Power Grids Thanh Long Vu and Konstantin Turitsyn, Member, IEEE Abstract The increasing development of the electric power
Modeling of Hydraulic Turbine and Governor for Dynamic Studies of HPP
Modeling of Hydraulic Turbine and Governor for Dynamic Studies of HPP Nanaware R. A. Department of Electronics, Shivaji University, Kolhapur Sawant S. R. Department of Technology, Shivaji University, Kolhapur
Transient stability improvement by using PSS and increasing inertia of synchronous machine
American Journal of Electrical Power and Energy Systems 2014; 3(2): 45-49 Published online April 20, 2014 (http://www.sciencepublishinggroup.com/j/epes) doi:10.11648/j.epes.20140302.15 Transient stability