Name: Discussion Section:
|
|
- Mae McBride
- 5 years ago
- Views:
Transcription
1 CBE 141: Chemical Engineering Thermodynamics, Spring 2017, UC Berkeley Midterm 2 FORM A March 23, 2017 Time: 80 minutes, closed-book and closed-notes, one-sided 8 ½ x 11 equation sheet allowed Please show all work and clearly mark your answers. Write your name on any additional pages of scratch work. You must turn in your equation sheet with your exam. Point Totals: Problem Problem 5 15 Problem 6 15 Problem 7 15 Problem 8 20 Problem 9 20 Problem Problem Problem Total 185 1
2 Problem 1 (5 points) Consider a distillation (i.e. separation) of a heptane (boiling point C)/decane (boiling point C) mixture performed at constant pressure with multiple separation columns connected in series. There is only one inlet in the first column, and one outlet in the last column. Which of the following is always true? (Choose one) A. The volume of the liquid product at the outlet will increase if you increase the number of columns operated in series. B. The purity of the final separated product will decrease if you increase the number of columns operated in series. C. The vapor is enriched in the more volatile component, and the liquid is enriched in the less volatile component. D. The liquid is enriched in the more volatile component, and the vapor is enriched in the less volatile component. Problem 2 (5 points) Which of the following is NOT true? (Choose one) A. Multiple phases at the same temperature and pressure are in equilibrium when the chemical potential of each species is the same in all phases. B. For a pure species at equilibrium, the fugacities of the vapor and liquid phases are equal. C. The Poynting factor assumes that a fluid is incompressible. D. The Clausius-Clapeyron equation assumes that the vapor pressure of a gas is independent of temperature. Problem 3 (5 points) Pure species A exists as a mixture of liquid and vapor. The pressure for the liquid and vapor are the same (i.e. they are in mechanical equilibrium, P v = P l ), but the fugacity of the liquid is higher than the fugacity of the vapor (f l > f v ). What will happen? (Choose one) A. The amount of species A in the vapor phase will increase and the amount in liquid phase will decrease B. The amount of species A in the liquid phase will increase and the amount in the vapor phase will decrease C. Pressure will change so that chemical and mechanical forces balance D. Nothing will happen Problem 4 (5 points) For a refrigerator, the following are true (you may circle more than one answer): A) The coefficient of performance is larger than unity when 2Q absorbed>q rejected B) The coefficient of performance is always finite C) Q rejected is always larger than Q absorbed D) The work required to run a refrigeration cycle is always larger than zero E) The working fluid in a refrigeration cycle must have a low heat capacity 2
3 Problem 5: (15 points) For each of the statements below, mark whether they are true (T) or false (F): 1) For a system in which temperature and volume are held constant, equilibrium is reached when Gibbs free energy is minimized. 2) An adiabatic throttle is always an irreversible process. 3) As a fluid approaches ideal behavior, the fugacity coefficient approaches 1. 4) A refrigerator moves heat from a hot place to a cold place, extracting work in the process. 5) Fugacity is an extensive property. Problem 6 (15 points) a) Show that ( T V ) S = ( P S ) V b) Fill out the Maxwell relations below and state which Legendre transform of internal energy they can be derived from (hint: which combined first and second laws can represent these energy functions?): ( T P ) = S ( S V ) = T 3
4 Problem 7 (15 points) A tray of ice cubes is placed in a freezer having an ideal coefficient of performance of 10. If the room temperature is 32 C, will the ice cubes melt or remain frozen? 4
5 Problem 8 (20 points) a) Show that the definition for fugacity leads to f(p, T) Pe G R(P,T) RT f(p 2, T) f(p 1, T) = eg(p 2,T) G(P 1,T) RT where G R is the residual Gibbs free energy, G(P, T) is the total Gibbs free energy at pressure P and temperature T. The subscripts 1 and 2 denote an initial and final states respectively b) Estimate the fugacity coefficient (φ = f/p ) of methane at P = 5.0 MPa and T = 273 K AND, comment on what this result says about the interactions between methane molecules at these conditions (i.e. ideal? Non-ideal?). Tabulated values for methane at various pressures is given below. T (K) P (MPa) V (L/mol) H (kj/mol) S (J/mol*K) Note: R=8.31 J K -1 mol -1 5
6 Problem 9 (20 points) a) From the following definitions of residuals: P 0 H R = RT 2 ( Z dp ) T P P P 0 S R = RT ( Z dp ) T P P P 0 R (Z 1) dp P What is the expression for residual Gibbs free energy, G R, as a function of R,T,P, and Z? b) Find the residual Gibbs free energy for a fluid at pressure P, that obeys the truncated virial equation of state, which is Z = 1 + B (T)P 6
7 Problem 10 (30 points) a) Calculate the ideal work per mole needed to compress steam at 50 C and 10 KPa to 60 KPa. What is the temperature of the exiting stream? b) For a compressor that is 67% efficient, what is the actual work required for this process? c) What is the enthalpy of the exiting stream for the real process? You may use the following tabulated data (note, not all is needed) Temperature (C) Pressure (kpa) Volume (l/mol) Internal Energy (kj/mol) Enthalpy (kj/mol) Entropy (J/mol*K) Cv (J/mol*K) Cp (J/mol*K) liquid liquid liquid liquid liquid liquid liquid vapor vapor vapor vapor vapor vapor vapor vapor vapor vapor vapor vapor Phase Temperature (C) Pressure (kpa) Volume (l/mol) Internal Energy (kj/mol) Enthalpy (kj/mol) Entropy (J/mol*K) Cv (J/mol*K) Cp (J/mol*K) vapor vapor vapor vapor vapor vapor vapor vapor Phase 7
8 vapor vapor vapor vapor vapor vapor vapor vapor vapor vapor vapor vapor vapor Space provided for work. 8
9 Problem 11 (20 points) Below is a phase diagram for a mixture of heptane (more volatile) and decane (less volatile). The graph is plotted as a mole fraction of heptane. a) Label the y-axis with one of the following: [Enthalpy, Temperature, Pressure, Entropy, Miscibility] b) Label the dew line (point where condensation begins) and the bubble line (where liquid boiling begins) c) The liquid equilibrated from point A contains more (decane, heptane, or equal) than the liquid equilibrated from point B? d) The liquid equilibrated from point A boils at a (higher, lower, or same) temperature than the liquid equilibrated from point B? e) Draw the bubble line and the dew line on the graph below if we plot the molar composition (xaxis) as a function of decane mole fraction instead of heptane mole fraction. f) The area within the envelope (between dew and bubble lines) would [increase, decrease, stay the same] if we replace decane (boiling point C) with octane (boiling point 125 C). 9
10 Problem 12 (30 points) You are asked to build a vapor-compression refrigeration cycle. At your disposal, you have the following pieces of equipment: Condenser Evaporator Throttle Compressor a) On the T-S plot below, draw a vapor-compression refrigeration cycle b) Using arrows, label on the diagram the directionality of the cycle if you wanted to move heat from low to high temperature reservoirs c) For each segment of the cycle, label with one of the following: isobaric ; isochoric ; isothermal ; isentropic ; isenthalpic; athermal (each may be used more than once, or not at all) d) Draw an arrow labeled W for the segment of the cycle where work is either input into the cycle or where work is extracted from the cycle. Also: specify whether work is input into or extracted from the cycle at this segment. e) For each segment of the cycle, state which piece of equipment is used f) Running the vapor-compression cycle relies on the Joule-Thompson Effect. The Joule- Thompson coefficient is defined as: μ JT = ( T P ) H What step of the vapor-compression refrigeration cycle is this coefficient relevant for? What is the sign of the coefficient at this step? What would happen if the coefficient had the opposite sign? 10
11 Additional space provided for work. 11
12 Additional space provided for work. 12
13 Additional space provided for work. 13
Name: Discussion Section:
CBE 141: Chemical Engineering Thermodynamics, Spring 2017, UC Berkeley Midterm 2 FORM B March 23, 2017 Time: 80 minutes, closed-book and closed-notes, one-sided 8 ½ x 11 equation sheet allowed lease show
More informationName: Discussion Section:
CBE 141: Chemical Engineering Thermodynamics, Spring 2018, UC Berkeley Midterm 2 March 22, 2018 Time: 80 minutes, closed-book and closed-notes, one-sided 8 ½ x 11 equation sheet allowed Please show all
More informationChemical Engineering Thermodynamics Spring 2002
10.213 Chemical Engineering Thermodynamics Spring 2002 Test 2 Solution Problem 1 (35 points) High pressure steam (stream 1) at a rate of 1000 kg/h initially at 3.5 MPa and 350 ºC is expanded in a turbine
More informationName: Discussion Section:
CBE 141: Chemical Engineering Thermodynamics, Spring 2018, UC Berkeley Midterm 2 March 22, 2018 Time: 80 minutes, closed-book and closed-notes, one-sided 8 ½ x 11 equation sheet allowed Please show all
More informationDistinguish between an isothermal process and an adiabatic process as applied to an ideal gas (2)
1. This question is about thermodynamic processes. (a) Distinguish between an isothermal process and an adiabatic process as applied to an ideal gas.......... An ideal gas is held in a container by a moveable
More informationHandout 12: Thermodynamics. Zeroth law of thermodynamics
1 Handout 12: Thermodynamics Zeroth law of thermodynamics When two objects with different temperature are brought into contact, heat flows from the hotter body to a cooler one Heat flows until the temperatures
More information(1)5. Which of the following equations is always valid for a fixed mass system undergoing an irreversible or reversible process:
Last Name First Name ME 300 Engineering Thermodynamics Exam #2 Spring 2008 March 28, 2008 Form A Note : (i) (ii) (iii) (iv) Closed book, closed notes; one 8.5 x 11 sheet allowed. 60 points total; 60 minutes;
More informationFINAL EXAM. ME 200 Thermodynamics I, Spring 2013 CIRCLE YOUR LECTURE BELOW:
ME 200 Thermodynamics I, Spring 2013 CIRCLE YOUR LECTURE BELOW: Div. 5 7:30 am Div. 2 10:30 am Div. 4 12:30 am Prof. Naik Prof. Braun Prof. Bae Div. 3 2:30 pm Div. 1 4:30 pm Div. 6 4:30 pm Prof. Chen Prof.
More informationHandout 12: Thermodynamics. Zeroth law of thermodynamics
1 Handout 12: Thermodynamics Zeroth law of thermodynamics When two objects with different temperature are brought into contact, heat flows from the hotter body to a cooler one Heat flows until the temperatures
More informationThermodynamics of solids 5. Unary systems. Kwangheon Park Kyung Hee University Department of Nuclear Engineering
Thermodynamics of solids 5. Unary systems Kwangheon ark Kyung Hee University Department of Nuclear Engineering 5.1. Unary heterogeneous system definition Unary system: one component system. Unary heterogeneous
More informationUBMCC11 - THERMODYNAMICS. B.E (Marine Engineering) B 16 BASIC CONCEPTS AND FIRST LAW PART- A
UBMCC11 - THERMODYNAMICS B.E (Marine Engineering) B 16 UNIT I BASIC CONCEPTS AND FIRST LAW PART- A 1. What do you understand by pure substance? 2. Define thermodynamic system. 3. Name the different types
More informationA) 2.0 atm B) 2.2 atm C) 2.4 atm D) 2.9 atm E) 3.3 atm
Name: Date: 1. On a cold day ( 3 C), the gauge pressure on a tire reads 2.0 atm. If the tire is heated to 27 C, what will be the absolute pressure of the air inside the tire? A) 2.0 atm B) 2.2 atm C) 2.4
More informationThermodynamic Properties
Thermodynamic Properties (TP) Thermodynamic Properties Define and articulate some of the critical language and concepts of Thermodynamics Distinguish between the universe, system, surroundings, and boundary
More informationName: Discussion Section:
CBE 141: Chemical Engineering Thermodynamics, Spring 2018, UC Berkeley Midterm 1 February 13, 2018 Time: 80 minutes, closed-book and closed-notes, one-sided 8 ½ x 11 equation sheet allowed Please show
More informationME 200 Thermodynamics I, Spring 2015, Exam 3, 8 p.m. to 9 p.m. on April 14, 2015
ME 200 Thermodynamics I, Spring 2015, Exam 3, 8 p.m. to 9 p.m. on April 14, 2015 CIRCLE YOUR LECTURE BELOW: 7:30 a.m. 10:30 a.m. 12:30 p.m. 2:30 p.m. 4:30 p.m. Joglekar Chen Chen Kittel Naik INSTRUCTIONS
More informationME6301- ENGINEERING THERMODYNAMICS UNIT I BASIC CONCEPT AND FIRST LAW PART-A
ME6301- ENGINEERING THERMODYNAMICS UNIT I BASIC CONCEPT AND FIRST LAW PART-A 1. What is meant by thermodynamics system? (A/M 2006) Thermodynamics system is defined as any space or matter or group of matter
More informationUNIVERSITY OF SOUTHAMPTON
UNIVERSITY OF SOUTHAMPTON PHYS1013W1 SEMESTER 2 EXAMINATION 2014-2015 ENERGY AND MATTER Duration: 120 MINS (2 hours) This paper contains 8 questions. Answers to Section A and Section B must be in separate
More informationMass Transfer Operations I Prof. Bishnupada Mandal Department of Chemical Engineering Indian Institute of Technology, Guwahati
Mass Transfer Operations I Prof. Bishnupada Mandal Department of Chemical Engineering Indian Institute of Technology, Guwahati Module - 5 Distillation Lecture - 5 Fractional Distillation Welcome to the
More informationExam 3 Solutions. ClO g. At 200 K and a total pressure of 1.0 bar, the partial pressure ratio for the chlorine-containing compounds is p ClO2
Chemistry 360 Dr. Jean M. Standard Fall 2016 Name KEY Exam 3 Solutions 1.) (14 points) Consider the gas phase decomposition of chlorine dioxide, ClO 2, ClO 2 ( g) ClO ( g) + O ( g). At 200 K and a total
More information12. Heat of melting and evaporation of water
VS 12. Heat of melting and evaporation of water 12.1 Introduction The change of the physical state of a substance in general requires the absorption or release of heat. In this case, one speaks of a first
More informationChapter 12 PROPERTY RELATIONS. Department of Mechanical Engineering
Chapter 12 THERMODYNAMIC PROPERTY RELATIONS Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University it Objectives Develop fundamental relations between commonly encountered thermodynamic
More informationME 200 Final Exam December 12, :00 a.m. to 10:00 a.m.
CIRCLE YOUR LECTURE BELOW: First Name Last Name 7:30 a.m. 8:30 a.m. 10:30 a.m. 1:30 p.m. 3:30 p.m. Mongia Abraham Sojka Bae Naik ME 200 Final Exam December 12, 2011 8:00 a.m. to 10:00 a.m. INSTRUCTIONS
More informationUNIVERSITY OF SOUTHAMPTON
UNIVERSITY OF SOUTHAMPTON PHYS1013W1 SEMESTER 2 EXAMINATION 2014-2015 ENERGY AND MATTER Duration: 120 MINS (2 hours) This paper contains 8 questions. Answers to Section A and Section B must be in separate
More informationPractice Midterm Exam 1 March, 2011
NAME: MSE 508: Solid State Thermodynamics Department of Materials Science & Engineering Boise State University Spring 2011 Practice Midterm Exam 1 March, 2011 Problem Total Points Points Obtained 1. 2.
More informationChemical Engineering 141: Thermodynamics Spring 2012
Chemical Engineering 141: Thermodynamics Spring 2012 Thursday, February 23, 2011 Midterm I 80 minutes 115 points total Use of phone devices is not permitted Return your equation sheet with the exam 1.
More informationII/IV B.Tech (Regular) DEGREE EXAMINATION. (1X12 = 12 Marks) Answer ONE question from each unit.
Page 1 of 8 Hall Ticket Number: 14CH 404 II/IV B.Tech (Regular) DEGREE EXAMINATION June, 2016 Chemical Engineering Fourth Semester Engineering Thermodynamics Time: Three Hours Maximum : 60 Marks Answer
More informationPhysics 5D PRACTICE FINAL EXAM Fall 2013
Print your name: Physics 5D PRACTICE FINAL EXAM Fall 2013 Real Exam is Wednesday December 11 Thimann Lecture 3 4:00-7:00 pm Closed book exam two 8.5x11 sheets of notes ok Note: Avogadro s number N A =
More informationSpring_#8. Thermodynamics. Youngsuk Nam
Spring_#8 Thermodynamics Youngsuk Nam ysnam1@khu.ac.krac kr Ch.7: Entropy Apply the second law of thermodynamics to processes. Define a new property called entropy to quantify the secondlaw effects. Establish
More informationME 354 THERMODYNAMICS 2 MIDTERM EXAMINATION. Instructor: R. Culham. Name: Student ID Number: Instructions
ME 354 THERMODYNAMICS 2 MIDTERM EXAMINATION February 14, 2011 5:30 pm - 7:30 pm Instructor: R. Culham Name: Student ID Number: Instructions 1. This is a 2 hour, closed-book examination. 2. Answer all questions
More informationLecture 44: Review Thermodynamics I
ME 00 Thermodynamics I Lecture 44: Review Thermodynamics I Yong Li Shanghai Jiao Tong University Institute of Refrigeration and Cryogenics 800 Dong Chuan Road Shanghai, 0040, P. R. China Email : liyo@sjtu.edu.cn
More informationChemical Engineering Thermodynamics
Chemical Engineering Thermodynamics P Liquid P x 1 sat P 1 T sat T 2 T x 1 T x 1 T y 1 Liquid Vapour sat P 2 P x 1 P y 1 P y 1 Vapour sat T 1 x, y 1 1 x, y 1 1 Pradeep Ahuja Contents CHEMICAL ENGINEERING
More informationCHAPTER 7 ENTROPY. Copyright Hany A. Al-Ansary and S. I. Abdel-Khalik (2014) 1
CHAPTER 7 ENTROPY S. I. Abdel-Khalik (2014) 1 ENTROPY The Clausius Inequality The Clausius inequality states that for for all cycles, reversible or irreversible, engines or refrigerators: For internally-reversible
More informationThe first law of thermodynamics. U = internal energy. Q = amount of heat energy transfer
Thermodynamics Investigation of the energy transfer by heat and work and how natural systems behave (Q) Heat transfer of energy due to temp differences. (W) Work transfer of energy through mechanical means.
More informationUNIVERSITY OF VICTORIA CHEMISTRY 102 Midterm Test 2 March 13, pm (60 minutes) DISPLAY YOUR STUDENT ID CARD (ONECard) ON TOP OF YOUR DESK NOW
Version A UNIVERSITY OF VICTORIA CHEMISTRY 102 Midterm Test 2 March 13, 2015 5-6 pm (60 minutes) Version A DISPLAY YOUR STUDENT ID CARD (ONECard) ON TOP OF YOUR DESK NOW Answer all multiple choice questions
More informationUNIVERSITY OF VICTORIA CHEMISTRY 102 Midterm Test 2 March 13, pm (60 minutes) DISPLAY YOUR STUDENT ID CARD (ONECard) ON TOP OF YOUR DESK NOW
Version B UNIVERSITY OF VICTORIA CHEMISTRY 102 Midterm Test 2 March 13, 2015 5-6 pm (60 minutes) Version B DISPLAY YOUR STUDENT ID CARD (ONECard) ON TOP OF YOUR DESK NOW Answer all multiple choice questions
More informationChemistry Heat Review. Heat: Temperature: Enthalpy: Calorimetry: Activation energy:
Chemistry Heat Review Name Date Vocabulary Heat: Temperature: Enthalpy: Calorimetry: Activation energy: Formulas Heat of phase change Heat for temperature increase Heat of reaction Endothermic/Exothermic
More informationPractice Examinations Chem 393 Fall 2005 Time 1 hr 15 min for each set.
Practice Examinations Chem 393 Fall 2005 Time 1 hr 15 min for each set. The symbols used here are as discussed in the class. Use scratch paper as needed. Do not give more than one answer for any question.
More informationPHY214 Thermal & Kinetic Physics Duration: 2 hours 30 minutes
BSc Examination by course unit. Friday 5th May 01 10:00 1:30 PHY14 Thermal & Kinetic Physics Duration: hours 30 minutes YOU ARE NOT PERMITTED TO READ THE CONTENTS OF THIS QUESTION PAPER UNTIL INSTRUCTED
More informationBasic Thermodynamics Module 1
Basic Thermodynamics Module 1 Lecture 9: Thermodynamic Properties of Fluids Thermodynamic Properties of fluids Most useful properties: Properties like pressure, volume and temperature which can be measured
More information5/6/ :41 PM. Chapter 6. Using Entropy. Dr. Mohammad Abuhaiba, PE
Chapter 6 Using Entropy 1 2 Chapter Objective Means are introduced for analyzing systems from the 2 nd law perspective as they undergo processes that are not necessarily cycles. Objective: introduce entropy
More informationThis follows from the Clausius inequality as a consequence of the second law of thermodynamics. Therefore. (for reversible process only) (22.
Entropy Clausius inequality can be used to analyze the cyclic process in a quantitative manner. The second law became a law of wider applicability when Clausius introduced the property called entropy.
More informationEntropy & the Second Law of Thermodynamics
PHYS102 Previous Exam Problems CHAPTER 20 Entropy & the Second Law of Thermodynamics Entropy gases Entropy solids & liquids Heat engines Refrigerators Second law of thermodynamics 1. The efficiency of
More informationClassification following properties of the system in Intensive and Extensive
Unit I Classification following properties of the system in Intensive and Extensive Extensive : mass, weight, volume, potential energy, Kinetic energy, Internal energy, entropy, exergy, energy, magnetization
More informationExam 1 Solutions 100 points
Chemistry 360 Fall 018 Dr. Jean M. Standard September 19, 018 Name KEY Exam 1 Solutions 100 points 1.) (14 points) A chunk of gold metal weighing 100.0 g at 800 K is dropped into 100.0 g of liquid water
More informationName: Class: Date: SHORT ANSWER Answer the following questions in the space provided.
CHAPTER 10 REVIEW States of Matter SECTION 1 SHORT ANSWER Answer the following questions in the space provided. 1. Identify whether the descriptions below describe an ideal gas or a real gas. a. The gas
More informationChemistry 360 Spring 2017 Dr. Jean M. Standard April 19, Exam points
Chemistry 360 pring 2017 Dr. Jean M. tandard April 19, 2017 Name Exam 3 100 points Note: You must show your work on problems in order to receive full credit for any answers. You must turn in your equation
More informationCHEMICAL ENGINEERING THERMODYNAMICS. Andrew S. Rosen
CHEMICAL ENGINEERING THERMODYNAMICS Andrew S. Rosen SYMBOL DICTIONARY 1 TABLE OF CONTENTS Symbol Dictionary... 3 1. Measured Thermodynamic Properties and Other Basic Concepts... 5 1.1 Preliminary Concepts
More informationQUESTION BANK UNIT-1 INTRODUCTION. 2. State zeroth law of thermodynamics? Write its importance in thermodynamics.
QUESTION BANK UNIT-1 INTRODUCTION 1. What do you mean by thermodynamic equilibrium? How does it differ from thermal equilibrium? [05 Marks, June-2015] 2. State zeroth law of thermodynamics? Write its importance
More information1985B4. A kilogram sample of a material is initially a solid at a temperature of 20 C. Heat is added to the sample at a constant rate of 100
1985B4. A 0.020-kilogram sample of a material is initially a solid at a temperature of 20 C. Heat is added to the sample at a constant rate of 100 joules per second until the temperature increases to 60
More informationN h (6.02x10 )(6.63x10 )
CHEM 5200 - Final Exam - December 13, 2018 INFORMATION PAGES (Use for reference and for scratch paper) Constants and Conversion Factors: R = 8.31 J/mol-K = 8.31 kpa-l/mol-k = 0.00831 kj/mol-k 1 L-atm =
More informationStandards 2.4 and 3.4. Background Standard 2.4 Conservation of Energy (Standard 6.5)
This experiment aims to explain the concepts of States of Matter, Heat, and Changes in Matter and is applicable to Standards 2.4 and 3.4. The successful student will be able to explain the three common
More informationI. (20%) Answer the following True (T) or False (F). If false, explain why for full credit.
I. (20%) Answer the following True (T) or False (F). If false, explain why for full credit. Both the Kelvin and Fahrenheit scales are absolute temperature scales. Specific volume, v, is an intensive property,
More informationUNIVERSITY COLLEGE LONDON. University of London EXAMINATION FOR INTERNAL STUDENTS. For The Following Qualifications:-
UNIVERSITY COLLEGE LONDON University of London EXAMINATION FOR INTERNAL STUDENTS For The Following Qualifications:- B.Sc. M.Sci. Physics 1B28: Thermal Physics COURSE CODE : PHYSIB28 UNIT VALUE : 0.50 DATE
More informationTHERMODYNAMICS WRITTEN TEST PORTION GOPHER INVITATIONAL JANUARY 6TH 2018 NAMES TEAM NAME AND NUMBER SCHOOL
THERMODYNAMICS WRITTEN TEST PORTION GOPHER INVITATIONAL JANUARY 6TH 2018 NAMES TEAM NAME AND NUMBER SCHOOL TIME ALLOWED: 30 MINUTES DO NOT TURN THE PAGE UNTIL YOU ARE INSTRUCTED TO DO SO. Multiple Choice:
More informationAP PHYSICS 2 WHS-CH-15 Thermodynamics Show all your work, equations used, and box in your answers!
AP PHYSICS 2 WHS-CH-15 Thermodynamics Show all your work, equations used, and box in your answers! Nicolas Léonard Sadi Carnot (1796-1832) Sadi Carnot was a French military engineer and physicist, often
More informationChapter 7. Entropy. by Asst.Prof. Dr.Woranee Paengjuntuek and Asst. Prof. Dr.Worarattana Pattaraprakorn
Chapter 7 Entropy by Asst.Prof. Dr.Woranee Paengjuntuek and Asst. Prof. Dr.Worarattana Pattaraprakorn Reference: Cengel, Yunus A. and Michael A. Boles, Thermodynamics: An Engineering Approach, 5th ed.,
More information3.20 Exam 1 Fall 2003 SOLUTIONS
3.0 Exam 1 Fall 003 SOLUIONS Question 1 You need to decide whether to work at constant volume or constant pressure. Since F is given, a natural choice is constant volume. Option 1: At constant and V :
More informationMAHALAKSHMI ENGINEERING COLLEGE
MAHALAKSHMI ENGINEERING COLLEGE TIRUCHIRAPALLI 621 213. Department: Mechanical Subject Code: ME2202 Semester: III Subject Name: ENGG. THERMODYNAMICS UNIT-I Basic Concept and First Law 1. What do you understand
More informationLast Name or Student ID
10/06/08, Chem433 Exam # 1 Last Name or Student ID 1. (3 pts) 2. (3 pts) 3. (3 pts) 4. (2 pts) 5. (2 pts) 6. (2 pts) 7. (2 pts) 8. (2 pts) 9. (6 pts) 10. (5 pts) 11. (6 pts) 12. (12 pts) 13. (22 pts) 14.
More informationCHEM Exam 2 - October 11, INFORMATION PAGE (Use for reference and for scratch paper)
CHEM 5200 - Exam 2 - October 11, 2018 INFORMATION PAGE (Use for reference and for scratch paper) Constants and Conversion Factors: R = 0.082 L-atm/mol-K = 8.31 J/mol-K = 8.31 kpa-l/mol-k 1 L-atm = 101
More informationThermodynamics: An Engineering Approach Seventh Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, Chapter 7 ENTROPY
Thermodynamics: An Engineering Approach Seventh Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011 Chapter 7 ENTROPY Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction
More informationPhysics 1301, Exam 4 Review
c V Andersen, 2006 1 Physics 1301, Exam 4 Review The following is a list of things you should definitely know for the exam, however, the list is not exhaustive. You are responsible for all the material
More informationUNIVERSITY OF TORONTO FACULTY OF APPLIED SCIENCE AND ENGINEERING TERM TEST 2 17 MARCH First Year APS 104S
UNIERSIY OF ORONO Please mark X to indicate your tutorial section. Failure to do so will result in a deduction of 3 marks. U 0 U 0 FACULY OF APPLIED SCIENCE AND ENGINEERING ERM ES 7 MARCH 05 U 03 U 04
More informationChapter 1 Introduction and Basic Concepts
Chapter 1 Introduction and Basic Concepts 1-1 Thermodynamics and Energy Application Areas of Thermodynamics 1-2 Importance of Dimensions and Units Some SI and English Units Dimensional Homogeneity Unity
More informationThe Second Law of Thermodynamics (Chapter 4)
The Second Law of Thermodynamics (Chapter 4) First Law: Energy of universe is constant: ΔE system = - ΔE surroundings Second Law: New variable, S, entropy. Changes in S, ΔS, tell us which processes made
More informationFinal Examination. Multiple Choice Questions. 1. The Virial expansion of the Compressibility Factor for a van der Waals gas is:
CHEM 331 Physical Chemistry I Fall 2013 Name: Final Examination Multiple Choice Questions 1. The Virial expansion of the Compressibility Factor for a van der Waals gas is: Z = 1 + + The Boyle Temperature
More informationR13. II B. Tech I Semester Regular Examinations, Jan THERMODYNAMICS (Com. to ME, AE, AME) PART- A
SET - 1 II B. Tech I Semester Regular Examinations, Jan - 2015 THERMODYNAMICS (Com. to ME, AE, AME) Time: 3 hours Max. Marks: 70 Note 1. Question Paper consists of two parts (Part-A and Part-B) 2. Answer
More informationENTROPY. Chapter 7. Mehmet Kanoglu. Thermodynamics: An Engineering Approach, 6 th Edition. Yunus A. Cengel, Michael A. Boles.
Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008 Chapter 7 ENTROPY Mehmet Kanoglu Copyright The McGraw-Hill Companies, Inc. Permission required
More informationME 200 Final Exam December 14, :00 a.m. to 10:00 a.m.
CIRCLE YOUR LECTURE BELOW: First Name Last Name 7:30 a.m. 8:30 a.m. 10:30 a.m. 11:30 a.m. Boregowda Boregowda Braun Bae 2:30 p.m. 3:30 p.m. 4:30 p.m. Meyer Naik Hess ME 200 Final Exam December 14, 2015
More informationTHERMODYNAMICS CONCEPTUAL PROBLEMS
THERMODYNAMICS CONCEPTUAL PROBLEMS Q-01 Is the heat supplied to a system always equal to the increases in its internal energy? Ans Acc. to first law of thermo- dynamics If heat is supplied in such a manner
More informationThermodynamics. Inaugural University of Michigan Science Olympiad Invitational Tournament. Test length: Minutes
Inaugural University of Michigan Science Olympiad Invitational Tournament Thermodynamics Test length: 20-25 Minutes Team number: School name: Student names: Instructions: Show work for all problems. Partial
More informationS.E. (Chemical Engineering) (Second Semester)EXAMINATION, 2012 THERMODYNAMICS-I (2008 PATTERN) Time : Three Hours Maximum Marks : 100
Total No. of Questions 12] [Total No. of Printed Pages 7 Seat No. [4162]-189 S.E. (Chemical Engineering) (Second Semester)EXAMINATION, 2012 THERMODYNAMICS-I (2008 PATTERN) Time : Three Hours Maximum Marks
More informationCM 3230 Thermodynamics, Fall 2016 Lecture 16
CM 3230 Thermodynamics, Fall 2016 Lecture 16 1. Joule-Thomsom Expansion - For a substance flowing adiabatically through a throttle (valve or pourous plug): in > out and negligible change in kinetic and
More informationTopic 3 &10 Review Thermodynamics
Name: Date: Topic 3 &10 Review Thermodynamics 1. The kelvin temperature of an object is a measure of A. the total energy of the molecules of the object. B. the total kinetic energy of the molecules of
More informationR13 SET - 1 '' ''' '' ' '''' Code No RT21033
SET - 1 II B. Tech I Semester Supplementary Examinations, June - 2015 THERMODYNAMICS (Com. to ME, AE, AME) Time: 3 hours Max. Marks: 70 Note: 1. Question Paper consists of two parts (Part-A and Part-B)
More informationReview of differential and integral calculus and introduction to multivariate differential calculus.
Chemistry 2301 Introduction: Review of terminology used in thermodynamics Review of differential and integral calculus and introduction to multivariate differential calculus. The properties of real gases:
More informationPhysics 360 Review 3
Physics 360 Review 3 The test will be similar to the second test in that calculators will not be allowed and that the Unit #2 material will be divided into three different parts. There will be one problem
More informationME 200 Exam 2 October 16, :30 p.m. to 7:30 p.m.
CIRCLE YOUR LECTURE BELOW: First Name Solution Last Name 7:30 am 8:30 am 10:30 am 11:30 am Joglekar Bae Gore Abraham 1:30 pm 3:30 pm 4:30 pm Naik Naik Cheung ME 200 Exam 2 October 16, 2013 6:30 p.m. to
More informationTable of Contents. Experiment 1: Vapour Pressure of Water at High Temperature 2. Experiment 2: Heat Capacity of Gases 5
1 Table of Contents EXPERIMENT PAGE Experiment 1: Vapour Pressure of Water at High Temperature 2 Experiment 2: Heat Capacity of Gases 5 Experiment 3: Joule-Thomson Effect 11 Experiment 4: Thermal and Electrical
More informationAll rights reserved. Armando B. Corripio, PhD, PE Flash Distillation Flash Drum Variables and Specifications... 2
Flash Distillation All rights reserved. Armando B. Corripio, PhD, PE. 2013 Contents Flash Distillation... 1 1 Flash Drum Variables and Specifications... 2 2 Flash Drum Balances and Equations... 4 2.1 Equilibrium
More informationTwo mark questions and answers UNIT II SECOND LAW 1. Define Clausius statement. It is impossible for a self-acting machine working in a cyclic process, to transfer heat from a body at lower temperature
More informationThermodynamics II. Week 9
hermodynamics II Week 9 Example Oxygen gas in a piston cylinder at 300K, 00 kpa with volume o. m 3 is compressed in a reversible adiabatic process to a final temperature of 700K. Find the final pressure
More informationClasses at: - Topic: Thermodynamics. = E v. = G f T 1
PHYSICAL CHEMISTRY by: SHAILENDRA KR. Classes at: - SCIENCE TUTORIALS; Opp. Khuda Baksh Library, Ashok Rajpath, Patna PIN POINT STUDY CIRCLE; House No. 5A/65, Opp. Mahual Kothi, Alpana Market, Patna Topic:
More informationBusiness. Final Exam Review. Competencies. Schedule Today. Most missed on Exam 3. Review Exam #3
Business Final Exam Review Online course evaluation (19/32 = 59%) Counts as a homework assignment (by Thurs) Professional program application Past due! Case study due today by 5 pm Leadership evaluation
More informationThermodynamics: An Engineering Approach Seventh Edition in SI Units Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011.
Thermodynamics: An Engineering Approach Seventh Edition in SI Units Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011 Chapter 7 ENTROPY Mehmet Kanoglu University of Gaziantep Copyright The McGraw-Hill
More informationTHE SECOND LAW OF THERMODYNAMICS. Professor Benjamin G. Levine CEM 182H Lecture 5
THE SECOND LAW OF THERMODYNAMICS Professor Benjamin G. Levine CEM 182H Lecture 5 Chemical Equilibrium N 2 + 3 H 2 2 NH 3 Chemical reactions go in both directions Systems started from any initial state
More informationCHEMISTRY 443, Fall, 2014 (14F) Section Number: 10 Examination 2, November 5, 2014
NAME: CHEMISTRY 443, Fall, 2014 (14F) Section Number: 10 Examination 2, November 5, 2014 Answer each question in the space provided; use back of page if extra space is needed. Answer questions so the grader
More informationCHAPTER 4 Physical Transformations of Pure Substances.
I. Generalities. CHAPTER 4 Physical Transformations of Pure Substances. A. Definitions: 1. A phase of a substance is a form of matter that is uniform throughout in chemical composition and physical state.
More informationsolid IMF>liquid IMF>gas IMF Draw a diagram to represent the 3 common states of matter of a given substance: solid liquid gas
Thermochemistry Part 1 Notes States of Matter and Intermolecular Forces (IMF) Chemistry HP At the end of this unit, students should be able to: Describe the various states of matter in terms of kinetic
More informationBasic Thermodynamics Prof. S. K. Som Department of Mechanical Engineering Indian Institute of Technology, Kharagpur
Basic Thermodynamics Prof. S. K. Som Department of Mechanical Engineering Indian Institute of Technology, Kharagpur Lecture - 15 Joule-Kelvin Expansion; Properties of Pure Substances Good morning. Last
More informationPhysics 202 Homework 5
Physics 202 Homework 5 Apr 29, 2013 1. A nuclear-fueled electric power plant utilizes a so-called boiling water reac- 5.8 C tor. In this type of reactor, nuclear energy causes water under pressure to boil
More informationCHEM 305 Solutions for assignment #4
CEM 05 Solutions for assignment #4 5. A heat engine based on a Carnot cycle does.50 kj of work per cycle and has an efficiency of 45.0%. What are q and q C for one cycle? Since the engine does work on
More informationTtions, and its relation to states of matter. This chapter covers the
Related Commercial Resources CHAPTER 1 THERMODYNAMICS AND REFRIGERATION CYCLES THERMODYNAMICS... 1.1 First Law of Thermodynamics... 1.2 Second Law of Thermodynamics... 1.2 Thermodynamic Analysis of Refrigeration
More informationThe First Law of Thermodynamics
Thermodynamics The First Law of Thermodynamics Thermodynamic Processes (isobaric, isochoric, isothermal, adiabatic) Reversible and Irreversible Processes Heat Engines Refrigerators and Heat Pumps The Carnot
More informationClass 22 - Second Law of Thermodynamics and Entropy
Class 22 - Second Law of Thermodynamics and Entropy The second law of thermodynamics The first law relates heat energy, work and the internal thermal energy of a system, and is essentially a statement
More informationPhysics 119A Final Examination
First letter of last name Name: Perm #: Email: Physics 119A Final Examination Thursday 10 December, 2009 Question 1 / 25 Question 2 / 25 Question 3 / 15 Question 4 / 20 Question 5 / 15 BONUS Total / 100
More informationLecture 35: Vapor power systems, Rankine cycle
ME 00 Thermodynamics I Spring 015 Lecture 35: Vapor power systems, Rankine cycle Yong Li Shanghai Jiao Tong University Institute of Refrigeration and Cryogenics 800 Dong Chuan Road Shanghai, 0040, P. R.
More informationME 201 Thermodynamics
Spring 01 ME 01 Thermodynamics Property Evaluation Practice Problems II Solutions 1. Air at 100 K and 1 MPa goes to MPa isenthapically. Determine the entropy change. Substance Type: Ideal Gas (air) Process:
More informationLecture. Polymer Thermodynamics 0331 L First and Second Law of Thermodynamics
1 Prof. Dr. rer. nat. habil. S. Enders Faculty III for Process Science Institute of Chemical Engineering Department of hermodynamics Lecture Polymer hermodynamics 0331 L 337 2.1. First Law of hermodynamics
More informationTemperature and Thermometers. Temperature is a measure of how hot or cold something is. Most materials expand when heated.
Heat Energy Temperature and Thermometers Temperature is a measure of how hot or cold something is. Most materials expand when heated. Thermometers are instruments designed to measure temperature. In order
More information