Physics 476LW Advanced Physics Laboratory Michelson Interferometer
|
|
- Millicent Eaton
- 5 years ago
- Views:
Transcription
1 Physics 476LW Advanced Physics Laboratory Michelson Interferometer Introduction An optical interferometer is an instrument which splits a beam of light into two beams, each beam follows a different path and the beams are recombined. The difference in the optical path lengths yields an interference pattern. Interferometers have found many uses. Michelson and Morely used a Michelson interferometer to determine that there was no ether, and a huge Michelson interferometer is now being used to detect gravity waves. There are two basic types of interferometers, the wavefront -splitting interferometers as exemplified by the Young's experiment device, and the amplitude-splitting interferometers. The Michelson interferometer is an amplitude-splitting interferometer. There are many uses of the Michelson interferometer in this laboratory we will explore three. Caution DO NOT allow a collimated laser beam enter your eye either directly or from a mirror or other smooth reflecting surface. It may cause permanent damage. For the low power laser used in this lab, it is safe to view light reflected from a diffuse surface such as the alignment towers or paddles. Do not touch any of the optical surfaces such as the mirrors, lenses, or samples. The oil from your skin will permanently degrade the optical finish. Theory Read the relevant section in an optics textbook (e.g. Introduction to Optics by Pedrotti, Pedrotti and Pedrotti) and the attached documents. The Experiment Apparatus In order to perform the experiments of this laboratory we must first build and align a Michelson interferometer. The instrument consists of a monochromatic laser light source, two guiding mirrors, a beam splitter, two plane reflecting mirrors, and adjustment micrometers. The parts are laid out as illustrated in the diagram and picture below. See the appendix for labeled photographs of each of the components. As you can see from the photograph (1) (see appendix) the laser is powered by a special Department of Physics 8/22/11 1 of 6
2 power supply with the output port in the back. The components are attached to the optical table by cap screws. The attachments should be snug but not over tight. You should use the hex driver to tighten the screws. The flexure stage and differential micrometer is a remarkable arrangement. Instead of using gears or friction to control the length of the second arm of the interferometer, it uses potential energy stored as deflection stress in the metal of the flexure stage. This arrangement eliminates the backlash and slippage inherent in gears and friction devices. Figure 1 Department of Physics 8/22/11 2 of 6
3 Figure 2. Photograph of Michelson Interferometer Setup Notes: When setting up the interferometer cover the laser with the black cloth shroud while positioning the next component to minimize the possibility of eye injury. When you must use the laser when adjusting mirrors use caution! Be sure that you will not reflect the beam into anyone's eye. There are two alternate methods for building and aligning the your interferometer. You can follow the method outlined below. This method will take about an hour to build your interferometer and another hour to align it. Alternatively, you can take short cuts building the interferometer. This method will take about a half hour to build the interferometer and several days to align it, if you are lucky. Take your pick. 1. Set the power supply at a corner of the optical table. Do not plug it in yet. 2. Assemble the laser in its base. Do not over tighten the brass nuts. After leaving room for the first guiding mirror, use two bolts to fasten the laser base to the optical table. Skip one hole and align the laser with the holes in the table. See picture above.(figure 2) 3. Plug the laser power cord into the back of the power controller and plug the controller into the wall socket. 4. Place the alignment tower with the tall side facing the laser at roughly the place Department of Physics 8/22/11 3 of 6
4 where the first guide mirror will be. Turn on the laser power. It will take a few seconds for the laser beam to appear. Adjust the laser so that the beam passes through the hole in the tower. This will start the beam on a level course. 5. Cover the laser with the shroud so that the beam is not visible. 6. Place the first guiding mirror so that the beam strikes the center of the mirror. The beam will now make a 90 degree turn. Cover the laser. 7. After allowing sufficient room for all the intervening components, place the alignment tower where the second guiding mirror will go and adjust the first guiding mirror so that the beam again passes through the hole in the tower. Now put the second guiding mirror on the translation stage and position it so that the beam strikes the center of the mirror. Cover the laser. 8. Taking care with the beam, place the beam splitter at 45 degrees to the line of the beam and bolt it to the optical table so that the beam strikes the center of the beam splitter. Cover the laser. 9. Put an alignment paddle in front of the beam splitter. Adjust the guiding mirrors so that the beam passes though the hole in the paddle. Remove the paddle and cover the laser. 10. Assemble alignment mirror #1 on its base. Be sure to use mirror #1 which has the adjustment screw in the lower center of the back. Bolt the micrometer stage to the table so that its center is roughly on the line of the beam coming from the beam splitter. Attach the mirror and stage to the stage with the four short screws. 11. Place an alignment paddle on the beam splitter so that the beam passes through the hole in the paddle and strikes mirror #1. Adjust mirror #1 so that it returns the beam as close to the hole in the paddle as possible. 12. Carefully assemble mirror #2 and the flexure base. Bolt the flexure base to the optical table so that its center is as close as possible to the line of the beam. 13. Insert the flexure positioning rod into the flexure with the flat end in the flexure. Slide the guide onto the rod and bolt it to the table. 14. Now we are ready to put the stress on the flexure stage. Set the vernier on the Mitutoyo differential micrometer to 0.5. Carefully adjust the positioning rod so that it presses the ball inside the flexure against the inside wall. Position the differential micrometer so that it just touches the round end of the positioning rod and bolt it to the table. Turn the micrometer to zero. The flexure is now under stress. 15. Place one alignment paddle after the beam splitter and the other in front of the mirror on the flexure. Align the beam so that it passes through both holes. 16. At this point there should be one or possibly two beam spots on the white screen. If there are two spots adjust them until there is only one. 17. Place the mirror which is on the tall stand so that it reflects the spot onto another mirror placed on the wall away from the white screen. Adjust this mirror so that it reflects onto the white screen. 18. Use adjusting mirrors to adjust the spot on the white screen to be as solid as possible. You may also use the micrometer on the arm with mirror #1 to help achieve precise alignment. Department of Physics 8/22/11 4 of 6
5 Procedures Measuring the Wavelength of the laser light. 1. After you have precisely aligned the interferometer, slowly change the length of the arm with the flexure by carefully turning the differential micrometer while at the same time counting the dark fringes as they pass through the spot projected on the screen. 2. Count at least 100 fringes. Then use the formula: λ = 2Δd Δm where, λ is wavelength, 2Δd is the change in the optical path length for one of the beams of light (2*the micrometer reading), and Δm is number of fringes (100 for this case). 3. You should repeat this measurement at least ten times. Compare the wavelength you measured with the accepted value for a He-Ne laser. Measuring the Index of Refraction of Glass 1. Mount the glass sample on the rotating stage. 2. Bolt the sample between the beam splitter and mirror #1 taking pains to have it perpendicular to the beam. (Think about how to do it.) 3. Attach the stand off rotation rod to the rotation stage. 4. Realign the interferometer. 5. Slowly rotate the stage using the rotation rod. Count ten fringes passing through the projected spot. 6. Read the number of degrees which the stage has been rotated. 7. Calculate the index of refraction using the formula: n = (2t Mλ)(1 cosθ) 2t(1 cosθ) Mλ where n is refractive index, t the thickness of the glass, M the number of shifted fringes, and theta the angle of rotation of the glass plate. 1. You should repeat this measurement at least three times. 2. The glass sample is one millimeter thick. Analysis Department of Physics 8/22/11 5 of 6
6 Calculate the wavelength of the laser light and the refractive index of the glass using your data, deriving the equations that you used. Discuss the systematic and statistical errors that affect your determination of both the wavelength of the laser light and the refractive index of the glass. Department of Physics 8/22/11 6 of 6
Experiment O-2. The Michelson Interferometer
Experiment O-2 The Michelson Interferometer The Michelson interferometer is one of the best known and historically important interferometers. It is a very accurate length-measuring device and has been
More informationExperiment 3 1. The Michelson Interferometer and the He- Ne Laser Physics 2150 Experiment No. 3 University of Colorado
Experiment 3 1 Introduction The Michelson Interferometer and the He- Ne Laser Physics 2150 Experiment No. 3 University of Colorado The Michelson interferometer is one example of an optical interferometer.
More informationIntroduction. Procedure. In this experiment, you'll use the interferometer to EQUIPMENT NEEDED: Lens 18mm FL. Component holder.
12-7137A Precision Interferometer Experiment 1: Introduction to Interferometry EQUIPMENT NEEDED: Basic Interferometer (OS-9255A) Laser (OS-9171) Laser Alignment Bench (OS-9172) Interferometer Accessories
More informationLABORATORY WRITE-UP MICHELSON INTERFEROMETER LAB AUTHOR S NAME GOES HERE STUDENT NUMBER:
LABORATORY WRITE-UP MICHELSON INTERFEROMETER LAB AUTHOR S NAME GOES HERE STUDENT NUMBER: 111-22-3333 MICHELSON INTERFEROMETER 1. PURPOSE The purpose of this experiment is to give some practice in using
More informationExperiment 8 Michelson Interferometer
Experiment 8 Michelson Interferometer Introduction This week s experiment utilizes the Michelson interferometer. You are to measure the wavelength of the green mercury light, the wavelength of the sodium
More informationMichelson Interferometry and Measurement of the Sodium Doublet Splitting
Michelson Interferometry and Measurement of the Sodium Doublet Splitting PHYS 3330: Experiments in Optics Department of Physics and Astronomy, University of Georgia, Athens, Georgia 30602 (Dated: Revised
More informationMichelson Interferometer
Michelson Interferometer Objective Determination of the wave length of the light of the helium-neon laser by means of Michelson interferometer subsectionprinciple and Task Light is made to produce interference
More informationThe Michelson Interferometer as a Device for Measuring the Wavelength of a Helium-Neon Laser
Journal of Advanced Undergraduate Physics Laboratory Investigation Volume 3 2017-2018 Article 2 2018 The Michelson Interferometer as a Device for Measuring the Wavelength of a Helium-Neon Laser Carly E.
More informationMichelson Interferometer
Michelson Interferometer Farooq Hassan Roll no: 2012-10-0101 LUMS School of Science and Engineering November 13, 2010 1 Abstract Michelson Interferometer was first used in the classic experiment in 1887
More informationSpeed of Light in Air
Speed of Light in Air Electromagnetic waves represent energy in the form of oscillating electric and magnetic fields which propagate through vacuum with a speed c = 2.9979246x10 8 m/s. Electromagnetic
More informationPhysics 476LW. Advanced Physics Laboratory - Faraday Rotation
Physics 476LW Advanced Physics Laboratory The Faraday Effect Introduction In 1845 Michael Faraday suspected that there were connections between light and electromagnetism. He conducted a series of experiments
More informationThe Michelson Interferometer
Experiment #33 The Michelson Interferometer References 1. Your first year physics textbook. 2. Hecht, Optics, Addison Wesley - Chapter 9 in the 4th Ed. (2001). 3. Jenkins and White, Fundamentals of Optics
More informationExperiment 6: Interferometers
Experiment 6: Interferometers Nate Saffold nas2173@columbia.edu Office Hour: Mondays, 5:30PM-6:30PM @ Pupin 1216 INTRO TO EXPERIMENTAL PHYS-LAB 1493/1494/2699 NOTE: No labs and no lecture next week! Outline
More informationElectric Field Mapping
Electric Field Mapping Equipment: mapping board, U-probe, 5 resistive boards, templates, knob adjustable DC voltmeter, 4 long leads, 16 V DC for wall strip, 8 1/2 X 11 sheets of paper Reading: Topics of
More informationPhysics 476LW Advanced Physics Laboratory The Faraday Effect
Physics 476LW Advanced Physics Laboratory The Faraday Effect Introduction In 1845 Michael Faraday suspected that there were connections between light and electromagnetism. He conducted a series of experiments
More information4. Dispersion. The index of refraction of the prism at the input wavelength can be calculated using
4. Dispersion In this lab we will explore how the index of refraction of a material depends on the of the incident light. We first study the phenomenon of minimum deviation of a prism. We then measure
More informationElectric Field Mapping Lab 2. Precautions
TS 2-12-12 Electric Field Mapping Lab 2 1 Electric Field Mapping Lab 2 Equipment: mapping board, U-probe, resistive boards, templates, dc voltmeter (431B), 4 long leads, 16 V dc for wall strip Reading:
More informationChapter 1. Optical Interferometry. Introduction
Chapter 1 Optical Interferometry Experiment objectives: Assemble and align Michelson and Fabry-Perot interferometers, calibrate them using a laser of known wavelength, and then use them characterize the
More informationTHE DIFFRACTION GRATING SPECTROMETER
Purpose Theory THE DIFFRACTION GRATING SPECTROMETER a. To study diffraction of light using a diffraction grating spectrometer b. To measure the wavelengths of certain lines in the spectrum of the mercury
More informationMichelson Interferometer. crucial role in Einstein s development of the Special Theory of Relativity.
Michelson Interferometer The interferometer Michelson experiment Interferometer of Michelson and Morley played 0 a crucial role in Einstein s development of the Special Theory of Relativity. Michelson
More informationAssembly Manual for the Brevard Astronomical Society 16 inch F4.5 Dobsonian Telescope Brevard Astronomical Society P.O. Box 1084 Cocoa, FL 32922
BAS 16 Telescope Manual Rev 1 Assembly Manual for the Brevard Astronomical Society 16 inch F4.5 Dobsonian Telescope Brevard Astronomical Society P.O. Box 1084 Cocoa, FL 32922 TABLE OF CONTENTS SECTION
More informationInterferometers. PART 1: Michelson Interferometer The Michelson interferometer is one of the most useful of all optical instru
Interferometers EP421 Lab Interferometers Introduction: Interferometers are the key to accurate distance measurement using optics. Historically, when mechanical measurements dominated, interferometers
More information2. OPERATIONAL CONDITIONS
1. INTRODUCTION This device was designed for modern physics labs of colleges and graduate schools. It demonstrates the influence of a magnetic field on light, known as Zeeman Effect, and reveals the behavior
More informationHow to use a Micrometer
1 Introduction How to use a Micrometer By Marc Yarnall ENGL 202C A micrometer is a measuring device that uses a calibrated screw to measure small distances with high precision. All micrometers can measure
More informationAtomic Spectra HISTORY AND THEORY
Atomic Spectra HISTORY AND THEORY When atoms of a gas are excited (by high voltage, for instance) they will give off light. Each element (in fact, each isotope) gives off a characteristic atomic spectrum,
More informationMeasurments with Michelson interferometers
Please do not remove this manual from from the lab. It is available at www.cm.ph.bham.ac.uk/y2lab Optics Measurments with Michelson interferometers Objectives In this experiment you will: Understand the
More informationThe Michelson Interferometer and the He-Ne Laser Physics 2150 Experiment No. 3 University of Colorado
Experiment 3 1 Introduction The Michelson Interferometer and the He-Ne Laser Physics 2150 Experiment No. 3 University of Colorado In the experiment, two different types of measurements will be made with
More information10 - Celestron Telescope II: Operation
10 - Celestron Telescope II: Operation Purpose: Gain more experience setting up a 6 Celestron telescope, familiarize yourself with the software interface, and acquire an image with the CCD camera. Due:
More informationINTERFEROMETERS. There are 4 principal types of measurements that can be made with this type of interferometer.
INTERFEROMETERS NOTE: Most mirrors in the apparatus are front surface aluminized. Do not touch the surfaces nor wipe them. they can be easily permanently damaged. Introduction This experiment provides
More informationExperiment 2: The Speed of Light
Experiment 2: The Speed of Light Modern Physics Laboratory Department of Physics and Astronomy Austin Peay State University September 12, 2006 Abstract In this experiment you will determine the value of
More information8. The Michelson Interferometer
M 8. The Michelson Interferometer 8.1 Introduction Interference patterns from superposed coherent waves may be used for precise determination of wavelength or, if the wavelength is known, time-of-flight,
More information5 TH ERMAL GRADIENT INTERFEROMETRIC MEASUREMENT
5 TH ERMAL GRADIENT INTERFEROMETRIC MEASUREMENT Gradient Index Measurement with Temperature MODEL OEK-100 PROJECT #4 50 5.1 Introduction It is possible to measure the change in index of refraction of a
More informationExperiment #5: Cauchy s Formula
Experiment #5: Cauchy s Formula Carl Adams October 14, 2011 1 Purpose This experiment is a continuation of Experiment #4. It is assumed you have an aligned spectrometer. 2 Safety/Protocol 1. The gas discharge
More informationElectric Field Mapping
Electric Field Mapping Equipment: mapping board, U-probe, 5 resistive boards, templates, 4 long leads, Phywe 07035.00 voltmeter, DC wall voltage output, 3 pieces of paper Precautions 1. Before turning
More informationAtomic and nuclear physics
Atomic and nuclear physics Atomic shell Normal Zeeman effect LEYBOLD Physics Leaflets Observing the normal Zeeman effect in transverse and longitudinal Objects of the experiment Observing the line triplet
More informationOptics. Measuring the line spectra of inert gases and metal vapors using a prism spectrometer. LD Physics Leaflets P
Optics Spectrometer Prism spectrometer LD Physics Leaflets P5.7.1.1 Measuring the line spectra of inert gases and metal vapors using a prism spectrometer Objects of the experiment Adjusting the prism spectrometer.
More informationTHE HAVERFORD UNIVERSITY S STRAWBRIDGE OBSERVATORY S OF THE 16 MEADE. A quick guide to using the 16 Meade Schmidt-Cassegrain Telescope
THE S OF THE 16 MEADE HAVERFORD UNIVERSITY S STRAWBRIDGE OBSERVATORY A quick guide to using the 16 Meade Schmidt-Cassegrain Telescope First draft: Scott Engle, Fall 2010; Update: Steve Boughn, Fall 2012
More information4. Dispersion. The index of refraction of the prism at the input wavelength can be calculated using
4. Dispersion In this lab we will explore how the index of refraction of a material depends on the of the incident light. We first study the phenomenon of minimum deviation of a prism. We then measure
More informationPh 3455/MSE 3255 Experiment 2: Atomic Spectra
Ph 3455/MSE 3255 Experiment 2: Atomic Spectra Background Reading: Tipler, Llewellyn pp. 163-165 Apparatus: Spectrometer, sodium lamp, hydrogen lamp, mercury lamp, diffraction grating, watchmaker eyeglass,
More informationPHYSICS LAB Experiment 9 Fall 2004 THE TORSION PENDULUM
PHYSICS 83 - LAB Experiment 9 Fall 004 THE TORSION PENDULUM In this experiment we will study the torsion constants of three different rods, a brass rod, a thin steel rod and a thick steel rod. We will
More informationInterference- Michelson Interferometer. Interference lecture by Dr. T.Vishwam
Interference- Michelson Interferometer Interference lecture by Dr. T.Vishwam * Measurement of the coherence length of a spectral line * Measurement of thickness of thin transparent flakes * Measurement
More informationABSTRACT. The following values for the wavelength of the sodium doublet lines were calculated:
Determination of the wavelengths of the Sodium doublet lines and the measurement of the thickness of a thin transparent film using a Michelson interferometer Luke Pomfrey Tutor: Dr. P. Doel March 22, 2007
More informationRECON. How to Setup the Telescope to Observe. This guide will show you how to setup your telescope for observing. Written By: Brittany McCrigler
RECON How to Setup the Telescope to Observe This guide will show you how to setup your telescope for observing. Written By: Brittany McCrigler 2017 recon.dozuki.com Page 1 of 30 INTRODUCTION This guide
More informationTA/TI survey. Phy Phy
TA/TI survey https://webapps.pas.rochester.edu/secure/phpq/ Phy121 7 60 73 Phy123 1 6 11 Chapter 34 The Wave Nature of Light; Interference Units of Chapter 34 34-5 Interference in Thin Films 34-6 Michelson
More informationPS210 - Optical Techniques. Section VI
PS210 - Optical Techniques Section VI Section I Light as Waves, Rays and Photons Section II Geometrical Optics & Optical Instrumentation Section III Periodic and Non-Periodic (Aperiodic) Waves Section
More informationGalileo Telescope Solar Viewer Joseph Hora, Elizabeth Hora 2017/09/18
Galileo Telescope Solar Viewer Joseph Hora, Elizabeth Hora 2017/09/18 17 7.75 5 2 1.5 3 2 1.5 Materials: (all dimensions in inches) 3x plywood sheet 17 x 7.75 x ½ 3x wood block cut from 2x4: 5 x 2 x 1.5
More informationECEN 4606, UNDERGRADUATE OPTICS LAB
ECEN 4606, UNDERGRADUATE OPTICS LAB Lab 6: Polarization Original: Professor McLeod SUMMARY: In this lab you will become familiar with the basics of polarization and learn to use common optical elements
More informationMeasurements in Optics for Civil Engineers
Measurements in Optics for Civil Engineers I. FOCAL LENGTH OF LENSES The behavior of simplest optical devices can be described by the method of geometrical optics. For convex or converging and concave
More informationInterferometer for Squareness measurement
F Interferometer for Squareness measurement The deviation of squareness of two machine axes can be measured as follows: 1. The straightness of a machine axis is measured. 2. The Angular reflector stops
More informationMichelson Interferometry Hassan Mirza
Michelson Interferometry Hassan Mirza Queen Mary University, Department of Physics Mile End Road, London, England, E1 4NS Introduction Interferometry is a method of experiment in which electromagnetic
More informationEducational Objectives Determine which variable affects the frequency of a simple pendulum.
Physics Workshop Main Topic Subtopic Learning Level Technology Level Activity Type Motion Periodic Motion Middle Low Student Teacher s Notes Description: Test the length, mass, and amplitude of a pendulum
More informationPhysics 1020 Experiment 6. Equilibrium of a Rigid Body
1 2 Introduction Static equilibrium is defined as a state where an object is not moving in any way. The two conditions for the equilibrium of a rigid body (such as a meter stick) are 1. the vector sum
More informationSome Topics in Optics
Some Topics in Optics The HeNe LASER The index of refraction and dispersion Interference The Michelson Interferometer Diffraction Wavemeter Fabry-Pérot Etalon and Interferometer The Helium Neon LASER A
More informationExperiment 9. Emission Spectra. measure the emission spectrum of a source of light using the digital spectrometer.
Experiment 9 Emission Spectra 9.1 Objectives By the end of this experiment, you will be able to: measure the emission spectrum of a source of light using the digital spectrometer. find the wavelength of
More informationAtomic emission spectra experiment
Atomic emission spectra experiment Contents 1 Overview 1 2 Equipment 1 3 Measuring the grating spacing using the sodium D-lines 4 4 Measurement of hydrogen lines and the Rydberg Constant 5 5 Measurement
More informationPotential and Kinetic Energy
Lab VII Potential and Kinetic Energy 1 Introduction This is a lab about the interplay between kinetic and potential energy. While we can calculate forces and accelerations of an object as it moves along
More informationLab #13: Polarization
Lab #13: Polarization Introduction In this experiment we will investigate various properties associated with polarized light. We will study both its generation and application. Real world applications
More informationCircular Motion and Centripetal Force
[For International Campus Lab ONLY] Objective Measure the centripetal force with the radius, mass, and speed of a particle in uniform circular motion. Theory ----------------------------- Reference --------------------------
More informationLab 2: Mach Zender Interferometer Overview
Lab : Mach Zender Interferometer Overview Goals:. Study factors that govern the interference between two light waves with identical amplitudes and frequencies. Relative phase. Relative polarization. Learn
More informationDetermination of Cauchy s Contants
8. Determination of Cauchy s Contants 8.1 Objective: To determine Cauchy s Constants using a prism and spectrometer. Apparatus: Glass prism, spectrometer and mercury vapour lamp. 8. Theory: The wavelength
More informationDouble Slit is VERY IMPORTANT because it is evidence of waves. Only waves interfere like this.
Double Slit is VERY IMPORTANT because it is evidence of waves. Only waves interfere like this. Superposition of Sinusoidal Waves Assume two waves are traveling in the same direction, with the same frequency,
More informationOptical Interferometry
Optical Interferometry MIT Department of Physics The objective of this experiment is to observe the interference of light by combining coherent monochromatic light beams using a Michelson interferometer.
More informationAP Waves/Optics ~ Learning Guide
AP Waves/Optics ~ Learning Guide Name: Instructions: Using a pencil, answer the following questions. The guide is marked based on effort, completeness, thoughtfulness, and neatness (not accuracy). Do your
More informationParticle-Wave Duality and Which-Way Information
Particle-Wave Duality and Which-Way Information Graham Jensen and Samantha To University of Rochester, Rochester, NY 14627, U.S. September 25, 2013 Abstract Samantha To This experiment aimed to support
More informationMichelson Interferometer
Fakultät für Physik und Geowissenschaften Physikalisches Grundpraktikum O10e Michelson Interferometer Tasks 1. Adjust a Michelson interferometer and determine the wavelength of a He-Ne laser. 2. Measure
More informationMetrology Prof. Dr Kanakuppi Sadashivappa Bapuji Institute of Engineering and Technology Davangere
Metrology Prof. Dr Kanakuppi Sadashivappa Bapuji Institute of Engineering and Technology Davangere Lecture 32 Introduction To Comparators, Mechanical Comparators (Refer Slide Time: 00:15) I welcome you
More informationOptics Interference from Films Newton s Rings Michelson Interferometer
Optics Interference from Films Newton s Rings Michelson Interferometer Lana Sheridan De Anza College June 19, 2018 Last time diffraction patterns diffraction and interference resolution and Raleigh s criterion
More informationOPSE FINAL EXAM Fall 2016 YOU MUST SHOW YOUR WORK. ANSWERS THAT ARE NOT JUSTIFIED WILL BE GIVEN ZERO CREDIT.
CLOSED BOOK. Equation Sheet is provided. YOU MUST SHOW YOUR WORK. ANSWERS THAT ARE NOT JUSTIFIED WILL BE GIVEN ZERO CREDIT. ALL NUMERICAL ANSERS MUST HAVE UNITS INDICATED. (Except dimensionless units like
More informationExperiment #4: Optical Spectrometer and the Prism Deviation
Experiment #4: Optical Spectrometer and the Prism Deviation Carl Adams October 2, 2011 1 Purpose In the first part of this lab you will set up and become familiar with an optical spectrometer. In the second
More informationRuby crystals and the first laser A spectroscopy experiment
Introduction: In this experiment you will be studying a ruby crystal using spectroscopy. Ruby is made from sapphire (Al 2 O 3 ) which has been doped with chromium ions, Cr(3+). There are three sets of
More information1. Waves and Particles 2. Interference of Waves 3. Wave Nature of Light
1. Waves and Particles 2. Interference of Waves 3. Wave Nature of Light 1. Double-Slit Eperiment reading: Chapter 22 2. Single-Slit Diffraction reading: Chapter 22 3. Diffraction Grating reading: Chapter
More informationConstructive vs. destructive interference; Coherent vs. incoherent interference
Constructive vs. destructive interference; Coherent vs. incoherent interference Waves that combine in phase add up to relatively high irradiance. = Constructive interference (coherent) Waves that combine
More informationarxiv: v1 [physics.optics] 6 Jul 2009
v8 Measuring the Molecular Polarizability of Air M.J. Madsen, D.R. Brown, S.R. Krutz, and M.J. Milliman Department of Physics, Wabash College, Crawfordsville, IN 47933 (Dated: July 7, 2009) Abstract arxiv:0907.0782v1
More informationsaxon Instruction Manual saxon Grandeur Brass Telescope High quality optics
saxon High quality optics Instruction Manual saxon Grandeur Brass Telescope WARNING! Do not use the telescope to look at the sun without an appropriate solar filter. Looking at or near the sun can result
More informationHome Lab 15 Diffraction Gratings
Home Lab Lab 15 Diffraction Gratings Home Lab 15 Diffraction Gratings Activity 15 1: Diffraction from a Transmission Grating Objective: To accurately measure the wavelength of light from a laser pointer
More informationCoherence and width of spectral lines with Michelson interferometer
Coherence and width of spectral lines TEP Principle Fraunhofer and Fresnel diffraction, interference, spatial and time coherence, coherence conditions, coherence length for non punctual light sources,
More informationRevisiting Fizeau s Observations: Spectral study of Na source using Newton s rings. Abstract
Revisiting Fizeau s Observations: Spectral study of Na source using Newton s rings K S Umesh #, Denny Melkay, J Adithya, Sai Prem Shaji, N Ganesh, R Dharmaraj, Rajkumar Jain, S Nanjundan # Author for correspondence:
More informationTo determine the wavelengths of light emitted by a mercury vapour lamp by using a diffraction grating.
12. Diffraction grating OBJECT To determine the wavelengths of light emitted by a mercury vapour lamp by using a diffraction grating. INTRODUCTION: Consider a light beam transmitted through an aperture
More informationPhysics 313: Laboratory 8 - Polarization of Light Electric Fields
Physics 313: Laboratory 8 - Polarization of Light Electric Fields Introduction: The electric fields that compose light have a magnitude, phase, and direction. The oscillating phase of the field and the
More informationElastic Properties of Solids (One or two weights)
Elastic properties of solids Page 1 of 8 Elastic Properties of Solids (One or two weights) This is a rare experiment where you will get points for breaking a sample! The recommended textbooks and other
More informationTITLE: Interferometry: The Michelson Interferometer
TITLE: Interferometry: The Michelson Interferometer Contributed by: Yolanda Flores Baboquivari High School Summary: The lesson begins with a demonstration introducing students to interference fringes formed
More informationINSTRUCTION MANUAL. Laser Diode Sarcomere Length. Aurora Scientific Inc. 360 Industrial Parkway South, Unit 4 Aurora, Ontario, Canada L4G 3V7
INSTRUCTION MANUAL Model 902A Laser Diode Sarcomere Length May 6, 2013, Revision 3 Copyright 2008-2013 Aurora Scientific Inc. Aurora Scientific Inc. 360 Industrial Parkway South, Unit 4 Aurora, Ontario,
More informationE. K. A. ADVANCED PHYSICS LABORATORY PHYSICS 3081, 4051 FRAUNHOFER DIFFRACTION
E. K. A. ADVANCED PHYSICS LABORATORY PHYSICS 3081, 4051 FRAUNHOFER DIFFRACTION References for Fraunhofer Diffraction 1. Jenkins and White Fundamentals of Optics. Chapters on Fraunhofer diffraction and
More informationInterference. Reminder: Exam 2 and Review quiz, more details on the course website
Chapter 9 Interference Phys 322 Lecture 25 Reminder: Exam 2 and Review quiz, more details on the course website Interferometers Wavefront-splitting interferometers Amplitude-splitting interferometers ed
More informationLEAPERS, INC. RED/GREEN DOTS
LEAPERS, INC. 1 RED/GREEN DOTS range estimating scopes UTG reticle intensified scopes TOTAL SOLUTION TO YOUR NEEDS -COMMITMENT TO BEST QUALITY, BEST VALUE AND BEST SERVICEwww.LEAPERS.com 32700 Capitol
More informationn(λ) = c/v(λ). Figure 1: Dispersion curves for some common optical glass types.
Physics 2310 Lab 2: The Dispersion of Optical Glass Dr. Michael Pierce (Univ. of Wyoming) Based on a lab by Dr. M. Kruger (Univ. of Missouri, Kansas City) Purpose: The purpose of this lab is to introduce
More informationMASSACHUSETTS INSTITUTE OF TECHNOLOGY Department of Electrical Engineering and Computer Science
Student Name Date MASSACHUSETTS INSTITUTE OF TECHNOLOGY Department of Electrical Engineering and Computer Science 6.161 Modern Optics Project Laboratory Laboratory Exercise No. 3 Coherence and Interferometry
More informationCollimation Instructions Learn how to accurately collimate the optics in your telescope.
1 of 5 9/3/2008 5:10 AM Collimation Instructions Learn how to accurately collimate the optics in your telescope. Video Imaging Exciting real time imaging with your Obsession scope Cleaning your mirror
More informationElectron Microscopy Sciences INSTRUCTION MANUAL. Stereo Microscopes Non-illuminated Stands
Electron Microscopy Sciences 1 INSTRUCTION MANUAL Stereo Microscopes Non-illuminated Stands Model GL7-207: Binocular, 6.5:1 Zoom Ratio 10X to 65X, smooth ball bearing construction and Model GL7-307: Trinocular,
More informationOperating Instructions Spectro-Goniometer Student. 1 Functional Elements. 2 Safety Precautions. Figure 1: Spectro-Goniometer Student
Operating Instructions Spectro-Goniometer Student 1 Functional Elements Figure 1: Spectro-Goniometer Student 1. Adjustable entrance slit, holding screw for slit cover 2. Lock ring fixing entrance slit
More informationSimple Harmonic Motion - MBL
Simple Harmonic Motion - MBL In this experiment you will use a pendulum to investigate different aspects of simple harmonic motion. You will first examine qualitatively the period of a pendulum, as well
More informationScience Lab I Properties of Light
Art & Science of Light Fall 2007 Science Lab I Properties of Light Prepared by: Dr. Dharshi Bopegedera 1 Using the Filtergraph (15 minutes) 1. Turn on the filtergraph, place a card on it and look at the
More informationCAUTION! NEVER ATTEMPT TO LOOK AT THE SUN WITH UNLESS YOU HAVE A FULL-APERTURE SOLAR FILTER (NOT INCLUDED WITH
CAUTION! X NEVER ATTEMPT TO LOOK AT THE SUN WITH YOUR APERTURA DOBSONIAN TELESCOPE UNLESS YOU HAVE A FULL-APERTURE SOLAR FILTER (NOT INCLUDED WITH TELESCOPE) INSTALLED OVER THE OPEN END OF THE OPTICAL
More informationLab 8 Impulse and Momentum
b Lab 8 Impulse and Momentum Physics 211 Lab What You Need To Know: The Physics Today we will deal with two physical concepts: impulse and momentum. For both, it turns out to be harder to say what they
More informationPHYSICS 253 SAMPLE FINAL EXAM. Student Number. The last two pages of the exam have some equations and some physical constants.
PHYSICS 253 SAMPLE FINAL EXAM Name Student Number CHECK ONE: Instructor 1 10:00 Instructor 2 1:00 Note that problems 1-19 are worth 2 points each, while problem 20 is worth 15 points and problems 21 and
More informationThe Quantum Model of the Hydrogen Atom
Physics 109 Science 1 Experiment 1 1 The Quantum Model of the Hydrogen Atom In this experiment you will use a spectrometer to determine the wavelengths of the visible lines of atomic hydrogen. The goal
More informationNORTHERN ILLINOIS UNIVERSITY PHYSICS DEPARTMENT. Physics 211 E&M and Quantum Physics Spring Lab #9: Diffraction Spectroscopy
NORTHERN ILLINOIS UNIVERSITY PHYSICS DEPARTMENT Physics 211 E&M and Quantum Physics Spring 2018 Lab #9: Diffraction Spectroscopy Lab Writeup Due: Mon/Wed/Thu/Fri, April 30/ May 2/3/4, 2018 Background All
More informationPre-lab Quiz/PHYS 224 Coulomb s Law and Coulomb Constant. Your name Lab section
Pre-lab Quiz/PHYS 4 Coulomb s Law and Coulomb Constant Your name Lab section 1. What do you investigate in this lab?. Two identical parallel conducting plates in vacuum form a capacitor. The surface area
More informationAutomatic Level Maintenance Manual SAL-XX W/ AIR DAMPENED COMPENSATOR
Automatic Level Maintenance Manual SAL-XX W/ AIR DAMPENED COMPENSATOR CST/Berger 2001 SAL 20/24/28/32 PAGE 1 REV. C 071803 Automatic Level Maintenance Manual User Calibration and Testing... 3 Circular
More informationTHE ZEEMAN EFFECT PHYSICS 359E
THE ZEEMAN EFFECT PHYSICS 359E INTRODUCTION The Zeeman effect is a demonstration of spatial quantization of angular momentum in atomic physics. Since an electron circling a nucleus is analogous to a current
More information