ANALYSIS OF THE LIGHT WEIGHT DEFLECTOMETER IN-SITU STRESS AND STRAIN
|
|
- Emma Ryan
- 6 years ago
- Views:
Transcription
1 ANALYSIS OF THE LIGHT WEIGHT DEFLECTOMETER IN-SITU STRESS AND STRAIN Patrick K. Miller BSCE Tufts University MS Colorado School of Mines Project Engineer Olson Engineering
2 Purpose LWD Background To measure in-situ elastic modulus of soils QC/QA device Operation 1 person to operate 1-3 minutes per test Weighs approximately 20 kg Common Devices Prima 100 Zorn ZFG 2000 Prima 100 Zorn ZFG 2000
3 Current Analysis Technique Based upon Boussinesq s theoretical solution to a static load applied through a rigid circular plate on an elastic half-space. w = ( 1 ν ) F AGr 0 k = s F w peak peak 2 ( 1 ) 2ks ν E = Ar 0
4 Previous In-situ Stress and Strain Research Fleming (2000) Used in-situ stress sensors to measure stress induced by the LWD Did not explore drop height, plate diameter and soil type effects Did not measure in-situ strain Several Researchers have used stress sensors to measure in-situ stress levels from various loading conditions and devices. Few Researchers have used potentiometers, LVDT s, or accelerometers to measure in-situ displacement and/or strain produced by various devices.
5 Main Research Objectives Employ In-situ Sensors to Measure LWD Induced Stress and Strain Levels Characterize stress and strain state under LWD loading Determine how stress and strain vary with loading plate diameter and drop height (applied force) Compare Secant Modulus from in-situ stress and strain data to modulus value given by the current analysis method Characterize Influence Depth of the LWD
6 In-situ Stress and Strain Sensors Earth Pressure Cell (EPC) Linear-Variable-Differential- Transformer (LVDT) Displacement Transducer
7 Sensor Calibration EPC Calibration EPC s calibrated in a laboratory calibration device at UMN. Potential Issues include: stress concentrations, shadowing effects, variable temperature effects, etc. LVDT Calibration Factory calibration No known calibration issues
8 Sensor Placement Procedure EPC Placement Placed by hand in lightly compacted new lift Encased in a pocket of the calibration sand LVDT Placement Placed by hand in lightly compacted new lift
9 Soil Profiles Tested Test 1 Test 2 4 Locations tested for each profile (2 EPC, 2 LVDT) F F Buried EPCs
10 In-situ Stress Results Key Points Magnitude and duration of the stress pulse is greater in the sand than in the clay At the deepest layer, the homogeneous profile has a greater magnitude and duration than the layered profile
11 Contact Stress Distribution Terzaghi (1943) theorized that a rigid circular plate produces a: Inverse Parabolic Distribution on cohesive soils 2 ( 1 ) 2ks ν E = Ar A = 4 0 Parabolic Distribution on non-cohesive soils A = 3π / 4 Uniform Distribution on soils having mixed characteristics A = π Therefore: Uniform and Parabolic loadings produce E s of 127 and 170 % of the Inverse Parabolic loading
12 Employing Static Theory of Elasticity In-situ Stress Results The increase in stress at depth z due to a surface loading is given by: σ z(peak) = 2π 0 3 r q(r) z r drdα 2π / (r + z ) Experimental data verifies Terzaghi s theory of soil dependent contact stress Suggests that the LWD analysis should reflect the soil type tested
13 In-situ Stress Results Terzaghi also theorized that the contact stress between a rigid plate and soil is dependent upon the level of loading A cohesive material exhibits an inverse parabolic distribution at low levels of loading and trends toward a uniform distribution at loads producing failure The experimental data also appears to confirm this theory Therefore understanding the level of loading due to the LWD may also be important in the data analysis
14 Plate Diameter and Drop Height Effects Key Points Stress magnitude of 200 mm load plate is greater near the surface but not at depth The stress magnitude at each layer is proportional to the applied force (drop height)
15 Employing Static Theory of Elasticity The increase in strain at depth z is given by: Where: σ r In-situ Strain Results = σ θ = 2π 0 rq(r) 4π Using a constant modulus the insitu strain data was fit 2 r0 3zr z(1 2ν) 0 3/ / ( r + z ) ( r + z ) 1 ε z = [ σ z ν ( σ r + E drdα σ θ )] The strain decreased much more rapidly with depth than the stress Note that only the 200 mm plate and largest drop height produced measurable strain at the second layer of sensors
16 In-situ Strain Results An elastic modulus which increased with depth was utilized to fit the strain data It is well know that E increases with a decrease in deviator stress and an increase in confining stress, both cases exist here The exponentially increasing E provided the best fit The deviator and confining stress dependent E equation provided a much better fit than the constant E More data is needed to validate these findings
17 Stress/Strain Results The secant modulus of the vertical in-situ stress and strain data was calculated and deemed E r E r and E LWD values were significantly different, and displayed different trends E r vs. E LWD Values F peak (kn) C/C/C 200 mm E r (MPa) E LWD (MPa) S/C 300 mm E r (MPa) NA E LWD (MPa) NA
18 Conclusions Contact stress between the soil and LWD is dependent on the soil type and level of loading Cohesive soil ~ inverse parabolic distribution Non-cohesive soil ~ parabolic distribution Mixed characteristic soil ~ uniform distribution Strain decreased much more rapidly than stress with depth A modulus profile which increased with depth more closely matched the experimental strain data. The secant modulus values calculated from the in-situ stress and strain data did not compare well with values obtained from the LWD Continuing Research More data needed from all soil types, focusing near the surface Tactile sensors to measure pressure distribution Refinement/Laboratory calibration of strain sensors
19
20 LWD Prototype Key Components Piezoelectric Force Transducer Measures Applied Force Urethane Damper Effects Impulse Duration and Magnitude Geophone Measures Response of Loading Plate (velocity)
CHARACTERIZATION OF A TWO-LAYER SOIL SYSTEM USING A LIGHTWEIGHT DEFLECTOMETER WITH RADIAL SENSORS Paper #
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 CHARACTERIZATION OF A TWO-LAYER SOIL SYSTEM USING A LIGHTWEIGHT DEFLECTOMETER
More information1.8 Unconfined Compression Test
1-49 1.8 Unconfined Compression Test - It gives a quick and simple measurement of the undrained strength of cohesive, undisturbed soil specimens. 1) Testing method i) Trimming a sample. Length-diameter
More informationStandardizing Lightweight Deflectometer (LWD) Modulus Measurements for Compaction Quality Assurance LWD study TPF-5(285)
Standardizing Lightweight Deflectometer (LWD) Modulus Measurements for Compaction Quality Assurance LWD study TPF-5(285) Charles W. Schwartz University of Maryland College Park Project Status Meeting July-01-2014
More informationTC211 Workshop CALIBRATION OF RIGID INCLUSION PARAMETERS BASED ON. Jérôme Racinais. September 15, 2015 PRESSUMETER TEST RESULTS
Jérôme Racinais September 15, 215 TC211 Workshop CALIBRATION OF RIGID INCLUSION PARAMETERS BASED ON PRESSUMETER TEST RESULTS Table of contents 1. Reminder about pressuremeter tests 2. General behaviour
More informationNew light-weight device for measuring degree of compaction and dynamic load bearing capacity
New light-weight device for measuring degree of compaction and dynamic load bearing capacity Zoltán TOMPAI assistant lecturer Department of Highway and Railway Engineering Budapest University of Technology
More information2012 Road School Light Weight Deflectometer (LWD)
2012 Road School Light Weight Deflectometer (LWD) Nayyar Siddiki, M.S., P.E. Office of Geotechnical Services Outline Testing for Compaction NO 53 and chemically modified soils (Special Prov.) Changing
More informationCompressibility & Consolidation
CHAPTER Compressibility & Consolidation Settlement If a structure is placed on soil surface, then the soil will undergo an elastic and plastic deformation. In engineering practice, the deformation or reduction
More informationDynamic Analysis Contents - 1
Dynamic Analysis Contents - 1 TABLE OF CONTENTS 1 DYNAMIC ANALYSIS 1.1 Overview... 1-1 1.2 Relation to Equivalent-Linear Methods... 1-2 1.2.1 Characteristics of the Equivalent-Linear Method... 1-2 1.2.2
More informationNumerical Simulation of Intelligent Compaction Technology for Construction Quality Control
CAIT-UTC-029 Numerical Simulation of Intelligent Compaction Technology for Construction Quality Control Final Report December 2014 Cesar Carrasco Professor and Department Chair of Civil Engineering University
More informationThe University of Melbourne Engineering Mechanics
The University of Melbourne 436-291 Engineering Mechanics Tutorial Four Poisson s Ratio and Axial Loading Part A (Introductory) 1. (Problem 9-22 from Hibbeler - Statics and Mechanics of Materials) A short
More informationEvaluation of mechanistic-based compaction measurements for earthwork QC/QA
Graduate Theses and Dissertations Graduate College 21 Evaluation of mechanistic-based compaction measurements for earthwork QC/QA Jiake Zhang Iowa State University Follow this and additional works at:
More informationFlexible Pavement Stress Analysis
Flexible Pavement Stress Analysis Dr. Antonis Michael Frederick University Notes Courtesy of Dr. Christos Drakos, University of Florida Need to predict & understand stress/strain distribution within the
More informationProf. B V S Viswanadham, Department of Civil Engineering, IIT Bombay
56 Module 4: Lecture 7 on Stress-strain relationship and Shear strength of soils Contents Stress state, Mohr s circle analysis and Pole, Principal stressspace, Stress pathsin p-q space; Mohr-Coulomb failure
More informationExperimental Device for Measuring Sandy Soil Sinkage Parameters
Bull. Fac. Agr., Saga Univ. No Experimental Device for Measuring Sandy Soil Sinkage Parameters Nang Nguyen Van, Takaaki MATSUO, Tatsuya KOUMOTO * and Shigeki INABA ** (Laboratory of Agricultural Machinery,
More informationMechanical Engineering Ph.D. Preliminary Qualifying Examination Solid Mechanics February 25, 2002
student personal identification (ID) number on each sheet. Do not write your name on any sheet. #1. A homogeneous, isotropic, linear elastic bar has rectangular cross sectional area A, modulus of elasticity
More informationMechanical Properties of Materials
Mechanical Properties of Materials Strains Material Model Stresses Learning objectives Understand the qualitative and quantitative description of mechanical properties of materials. Learn the logic of
More informationA NEW TECHNIQUE FOR THE ESTIMATION OF THE ELASTIC MODULI OF PAVEMENT LAYERS FROM LIGHT WEIGHT DEFLECTOMETER DATA NICKEY AKBARIYEH
A NEW TECHNIQUE FOR THE ESTIMATION OF THE ELASTIC MODULI OF PAVEMENT LAYERS FROM LIGHT WEIGHT DEFLECTOMETER DATA by NICKEY AKBARIYEH Presented to the Faculty of the Graduate School of The University of
More informationDesign Procedures For Dynamically Loaded Foundations
Design Procedures For Dynamically Loaded Foundations 1/11 Choice of parameters for equivalent lumped systems Lumped mass : the mass of the foundation and supported machinery Damping : 1 Geometrical(or
More informationUse of the Light Falling Weight Deflectometer (LFWD) as a site investigation tool for residual soils and weak rock
Use of the Light Falling Weight Deflectometer (LFWD) as a site investigation tool for residual soils and weak rock Dr. David Lacey, Dr. Burt Look & Dave Marks Summary of Presentation Introduction Residual
More informationIMPACT RESPONSE ANALYSIS OF LARGE SCALE RC GIRDER WITH SAND CUSHION
-Technical Paper- IMPACT RESPONSE ANALYSIS OF LARGE SCALE RC GIRDER WITH SAND CUSHION Abdul Qadir BHATTI *1, Norimitsu KISHI *2, Shin-ya OKADA *3 and Hisashi KONNO *4 ABSTRACT In order to establish a proper
More informationHKIE-GD Workshop on Foundation Engineering 7 May Shallow Foundations. Dr Limin Zhang Hong Kong University of Science and Technology
HKIE-GD Workshop on Foundation Engineering 7 May 2011 Shallow Foundations Dr Limin Zhang Hong Kong University of Science and Technology 1 Outline Summary of design requirements Load eccentricity Bearing
More informationCubzac-les-Ponts Experimental Embankments on Soft Clay
Cubzac-les-Ponts Experimental Embankments on Soft Clay 1 Introduction In the 197 s, a series of test embankments were constructed on soft clay at Cubzac-les-Ponts in France. These full-scale field tests
More informationINTRODUCTION TO STRAIN
SIMPLE STRAIN INTRODUCTION TO STRAIN In general terms, Strain is a geometric quantity that measures the deformation of a body. There are two types of strain: normal strain: characterizes dimensional changes,
More informationExperimentally Calibrating Cohesive Zone Models for Structural Automotive Adhesives
Experimentally Calibrating Cohesive Zone Models for Structural Automotive Adhesives Mark Oliver October 19, 2016 Adhesives and Sealants Council Fall Convention contact@veryst.com www.veryst.com Outline
More informationStresses and Strains in flexible Pavements
Stresses and Strains in flexible Pavements Multi Layered Elastic System Assumptions in Multi Layered Elastic Systems The material properties of each layer are homogeneous property at point A i is the same
More informationEQUIVALENT FRACTURE ENERGY CONCEPT FOR DYNAMIC RESPONSE ANALYSIS OF PROTOTYPE RC GIRDERS
EQUIVALENT FRACTURE ENERGY CONCEPT FOR DYNAMIC RESPONSE ANALYSIS OF PROTOTYPE RC GIRDERS Abdul Qadir Bhatti 1, Norimitsu Kishi 2 and Khaliq U Rehman Shad 3 1 Assistant Professor, Dept. of Structural Engineering,
More informationSHEAR STRENGTH OF SOIL UNCONFINED COMPRESSION TEST
SHEAR STRENGTH OF SOIL DEFINITION The shear strength of the soil mass is the internal resistance per unit area that the soil mass can offer to resist failure and sliding along any plane inside it. INTRODUCTION
More informationACCELERATED IMPLEMENTATION OF INTELLIGENT COMPACTION TECHNOLOGY
ACCELERATED IMPLEMENTATION OF INTELLIGENT COMPACTION TECHNOLOGY FOR EMBANKMENT SUBGRADE SOILS, AGGREGATE BASE, AND ASPHALT PAVEMENT MATERIALS Draft Final Report Texas DOT FM6 Field Project July 2 to, 28
More information1.103 CIVIL ENGINEERING MATERIALS LABORATORY (1-2-3) Dr. J.T. Germaine Spring 2004 LABORATORY ASSIGNMENT NUMBER 6
1.103 CIVIL ENGINEERING MATERIALS LABORATORY (1-2-3) Dr. J.T. Germaine MIT Spring 2004 LABORATORY ASSIGNMENT NUMBER 6 COMPRESSION TESTING AND ANISOTROPY OF WOOD Purpose: Reading: During this laboratory
More informationPre-failure Deformability of Geomaterials. Hsin-yu Shan Dept. of Civil Engineering National Chiao Tung University
Pre-failure Deformability of Geomaterials Hsin-yu Shan Dept. of Civil Engineering National Chiao Tung University Strain Levels Strain at failure Sand Clay Rock Distribution of strain of soil in the field
More informationDevelopment and application of time-lapse ultrasonic tomography for laboratory characterisation of localised deformation in hard soils / soft rocks
Development and application of time-lapse ultrasonic tomography for laboratory characterisation of localised deformation in hard soils / soft rocks Erika Tudisco Research Group: Stephen A. Hall Philippe
More informationLecture 3: Stresses in Rigid Pavements
Lecture 3: Stresses in Rigid Pavements Nature of Responses under Flexible and Rigid Plates Flexible plate: Uniform Contact Pressure Variable Deflection Profile Flexible Plate Rigid Plate plate: Non-Uniform
More informationPullout Tests of Geogrids Embedded in Non-cohesive Soil
Archives of Hydro-Engineering and Environmental Mechanics Vol. 51 (2004), No. 2, pp. 135 147 Pullout Tests of Geogrids Embedded in Non-cohesive Soil Angelika Duszyńska, Adam F. Bolt Gdansk University of
More informationPart 7. Nonlinearity
Part 7 Nonlinearity Linear System Superposition, Convolution re ( ) re ( ) = r 1 1 = r re ( 1 + e) = r1 + r e excitation r = r() e response In the time domain: t rt () = et () ht () = e( τ) ht ( τ) dτ
More informationDynamics of structures
Dynamics of structures 2.Vibrations: single degree of freedom system Arnaud Deraemaeker (aderaema@ulb.ac.be) 1 Outline of the chapter *One degree of freedom systems in real life Hypothesis Examples *Response
More informationSoil strength. the strength depends on the applied stress. water pressures are required
Soil Strength Soil strength u Soils are essentially frictional materials the strength depends on the applied stress u Strength is controlled by effective stresses water pressures are required u Soil strength
More informationLecture 20. Measuring Pressure and Temperature (Chapter 9) Measuring Pressure Measuring Temperature MECH 373. Instrumentation and Measurements
MECH 373 Instrumentation and Measurements Lecture 20 Measuring Pressure and Temperature (Chapter 9) Measuring Pressure Measuring Temperature 1 Measuring Acceleration and Vibration Accelerometers using
More informationAnalysis of a single pile settlement
Engineering manual No. 14 Updated: 06/2018 Analysis of a single pile settlement Program: Pile File: Demo_manual_14.gpi The objective of this engineering manual is to explain the application of the GEO
More informationLateral Earth Pressure
1 of 11 6/2/2012 4:28 AM Lateral Earth Pressure The magnitude of lateral earth pressure depends on: 1. Shear strength characteristics of soil 2. Lateral strain condition 3. Pore water pressure 4. State
More informationEVALUATION OF DYNAMIC METHODS FOR EARTHWORK ASSESSMENT
Vol. 11, Issue 1/, 38-44 DOI:./cee--000 EVALUATION OF DYNAMIC METHODS FOR EARTHWORK ASSESSMENT Jozef VLČEK 1,*, Dominika ĎUREKOVÁ 2, Katarína ZGÚTOVÁ 2 1 Department of Geotechnics, Faculty of Civil Engineering,
More informationNORMAL STRESS. The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts.
NORMAL STRESS The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts. σ = force/area = P/A where σ = the normal stress P = the centric
More informationVERTICAL STRESS INCREASES IN SOIL TYPES OF LOADING. Point Loads (P) Line Loads (q/unit length) Examples: -Posts
VERTICAL STRESS INCREASES IN SOIL Point Loads (P) TYPES OF LOADING Line Loads (q/unit length) Revised 0/014 Figure 6.11. Das FGE (005). Examples: -Posts Figure 6.1. Das FGE (005). Examples: - Railroad
More informationDimension measurement. By Mr.Vuttichai Sittiarttakorn
Dimension measurement By Mr.Vuttichai Sittiarttakorn 1 LECTURE OUTLINE 1. Introduction 2. Standards and Calibration 3. Relative displacement : Translational and Rotational 4. displacement transducers Potentiometers
More informationLecture 19. Measurement of Solid-Mechanical Quantities (Chapter 8) Measuring Strain Measuring Displacement Measuring Linear Velocity
MECH 373 Instrumentation and Measurements Lecture 19 Measurement of Solid-Mechanical Quantities (Chapter 8) Measuring Strain Measuring Displacement Measuring Linear Velocity Measuring Accepleration and
More information20. Rheology & Linear Elasticity
I Main Topics A Rheology: Macroscopic deformation behavior B Linear elasticity for homogeneous isotropic materials 10/29/18 GG303 1 Viscous (fluid) Behavior http://manoa.hawaii.edu/graduate/content/slide-lava
More informationEE 5344 Introduction to MEMS CHAPTER 6 Mechanical Sensors. 1. Position Displacement x, θ 2. Velocity, speed Kinematic
I. Mechanical Measurands: 1. Classification of main types: EE 5344 Introduction MEMS CHAPTER 6 Mechanical Sensors 1. Position Displacement x, θ. Velocity, speed Kinematic dx dθ v =, = ω 3. Acceleration
More informationSoil and Rock Strength. Chapter 8 Shear Strength. Steel Strength. Concrete Strength. Dr. Talat Bader May Steel. Concrete.
Chapter 8 Shear Strength Dr. Talat Bader May 2006 Soil and Rock Strength Unconfined compressive strength (MPa) Steel Concrete 20 100 250 750 0.001 0.01 Soil 0.1 1.0 10 Rock 100 250 F y = 250 to 750 MPa
More informationEMA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 2 Stress & Strain - Axial Loading
MA 3702 Mechanics & Materials Science (Mechanics of Materials) Chapter 2 Stress & Strain - Axial Loading MA 3702 Mechanics & Materials Science Zhe Cheng (2018) 2 Stress & Strain - Axial Loading Statics
More informationHardened Concrete. Lecture No. 16
Hardened Concrete Lecture No. 16 Fatigue strength of concrete Modulus of elasticity, Creep Shrinkage of concrete Stress-Strain Plot of Concrete At stress below 30% of ultimate strength, the transition
More informationIntroduction and Background
Introduction and Background Itasca Consulting Group, Inc. (Itasca) has been participating in the geomechanical design of the underground 118-Zone at the Capstone Minto Mine (Minto) in the Yukon, in northwestern
More informationStress Rotations Due to Moving Wheel Loads and Their Effects on Pavement Materials Characterization
Stress Rotations Due to Moving Wheel Loads and Their Effects on Pavement Materials Characterization Erol Tutumluer June 9, 2005 OMP Brown Bag Seminar Presentation FAA Center of Excellence for Airport Technology
More information15. Supplementary Notes Conducted in Cooperation with the U.S. Department of Transportation, Federal Highway Administration
FHWA/LA/406 4. Title and Subtitle Development of Models to Estimate the Subgrade and Subbase Layers Resilient Modulus from In situ Devices Test Results for Construction Control 7. Author(s) Louay N. Mohammad,
More informationBack Calculation of Rock Mass Modulus using Finite Element Code (COMSOL)
Back Calculation of Rock Mass Modulus using Finite Element Code (COMSOL) Amirreza Ghasemi 1. Introduction Deformability is recognized as one of the most important parameters governing the behavior of rock
More information1 MPa = 150 psi 10 kn = 1 ton 25 mm = 1 inch
INTELLIGENT COMPACTION: AN OVERVIEW Developed by Jean-Louis Briaud Department of Civil Engineering Texas A&M University Presented to the 5 th Idaho Asphalt Conference, October 27, 5 By Fouad Bayomy Department
More informationApplication of DCP in Prediction of Resilient Modulus of Subgrade Soils
Application of DCP in Prediction of Resilient Modulus of Subgrade Soils Louay Mohammad, Ph.D. Louisiana Transportation Research Center Louisiana State University 2006 Pavement Performance Seminar April
More informationStress and Strains in Soil and Rock. Hsin-yu Shan Dept. of Civil Engineering National Chiao Tung University
Stress and Strains in Soil and Rock Hsin-yu Shan Dept. of Civil Engineering National Chiao Tung University Stress and Strain ε 1 1 2 ε 2 ε Dimension 1 2 0 ε ε ε 0 1 2 ε 1 1 2 ε 2 ε Plane Strain = 0 1 2
More informationStress Concentration. Professor Darrell F. Socie Darrell Socie, All Rights Reserved
Stress Concentration Professor Darrell F. Socie 004-014 Darrell Socie, All Rights Reserved Outline 1. Stress Concentration. Notch Rules 3. Fatigue Notch Factor 4. Stress Intensity Factors for Notches 5.
More informationMechanistic Pavement Design
Seminar on Pavement Design System and Pavement Performance Models Reykjavik, 22. 23. March, 2007 Mechanistic Pavement Design A Road to Enhanced Understanding of Pavement Performance Sigurdur Erlingsson
More informationMEMORANDUM SUBJECT: CERTIFICATE IN ROCK MECHANICS PAPER 1 : THEORY SUBJECT CODE: COMRMC MODERATOR: H YILMAZ EXAMINATION DATE: OCTOBER 2017 TIME:
MEMORANDUM SUBJECT: CERTIFICATE IN ROCK MECHANICS PAPER 1 : THEORY EXAMINER: WM BESTER SUBJECT CODE: COMRMC EXAMINATION DATE: OCTOBER 2017 TIME: MODERATOR: H YILMAZ TOTAL MARKS: [100] PASS MARK: (60%)
More informationSPR-4230: Alternative Quality Assurance Methods for Compacted Subgrade
SPR-4230: Alternative Quality Assurance Methods for Compacted Subgrade Peter J. Becker, PhD Indiana Department of Transportation Division of Research & Development Presentation Layout Project background
More informationDevelopment of resilient modulus prediction models for base and subgrade pavement layers from in situ devices test results
Louisiana State University LSU Digital Commons LSU Master's Theses Graduate School 2004 Development of resilient modulus prediction models for base and subgrade pavement layers from in situ devices test
More informationImpact of Water on the Structural Performance of Pavements
Impact of Water on the Structural Performance of Pavements S. Erlingsson Highway Engineering, VTI The Swedish National Road and Transport Research Institute, Linköping, Sweden & Faculty of Civil and Environmental
More informationIn Situ Triaxial Tests
Page No.: 1 More than 40 years have passed since, with all due urgency, STINI and MÜLLER pointed out the absolute necessity of conducting large-scale tests in engineering geology and rock mechanics. The
More informationMechanical resonances in the low-frequency vibration spectrum of a cylindrically symmetric, anti-tank landmine
Mechanical resonances in the low-frequency vibration spectrum of a cylindrically symmetric, anti-tank landmine W. C K Alberts a, J. M. Sabatier b and R. Waxler b a U.S. Army Research Laboratory, 2800 Powder
More informationThe science of elasticity
The science of elasticity In 1676 Hooke realized that 1.Every kind of solid changes shape when a mechanical force acts on it. 2.It is this change of shape which enables the solid to supply the reaction
More informationPractical Algorithm for large diameter pile tip bearing capacity based on displacement control RUAN Xiang 1, a
Advances in ngineering Research (AR), volume 43 6th International Conference on nergy and nvironmental Protection (ICP 207) Practical Algorithm for large diameter pile tip bearing capacity based on displacement
More informationResonant Column and Torsional Cyclic Shear System
Resonant Column and Torsional Cyclic Shear System Combined Resonant Column (RC) & Torsional Cyclic Shear (TCS) Test apparatus to determinate with saturated soil : Shear Modulus Damping Modulus versus Shear
More informationStiffness Estimates Using Portable Deflectometers
Hoffmann, O. J-M., Guzina, B. B., Drescher, A. Paper No. 04-2304 Stiffness Estimates Using Portable Deflectometers Submission dates: July 31, 2003 November 13, 2003 Word count: 6258 (4508 words, plus 1
More informationREPRODUCTION OF A LARGE-SCALE 1G TEST ON UNSATURATED SAND DEPOSITS AND PILE FOUNDATIONS USING CENTRIFUGE MODELING
REPRODUCTION OF A LARGE-SCALE G TEST ON UNSATURATED SAND DEPOSITS AND PILE FOUNDATIONS USING CENTRIFUGE MODELING 293 Masayoshi SATO, Takaaki KAGAWA 2 And Chikahiro MINOWA 3 SUMMARY A dynamic centrifuge
More informationAxially Loaded Piles
Axially Loaded Piles 1 t- Curve Method using Finite Element Analysis The stress-strain relationship for an axially loaded pile can be described through three loading mechanisms: axial deformation in the
More informationME 515 Mechatronics. Overview of Computer based Control System
ME 515 Mechatronics Introduction to Sensors I Asanga Ratnaweera Department of Faculty of Engineering University of Peradeniya Tel: 081239 (3627) Email: asangar@pdn.ac.lk Overview of Computer based Control
More informationSENSORS and TRANSDUCERS
SENSORS and TRANSDUCERS Tadeusz Stepinski, Signaler och system The Mechanical Energy Domain Physics Surface acoustic waves Silicon microresonators Variable resistance sensors Piezoelectric sensors Capacitive
More information13 th World Conference on Earthquake Engineering Vancouver, B.C., Canada August 1-6, 2004 Paper No. 3016
13 th World Conference on Earthquake Engineering Vancouver, B.C., Canada August 1-6, 2004 Paper No. 3016 SOLUTIONS FOR MITIGATING SOIL LIQUEFACTION EFFECTS A NUMERICAL STUDUY AHMAD JAFARI MEHRABADI 1 AND
More informationChristian Linde Olsen Griffith University, Faculty of Engineering and Information Technology, Gold Coast Campus.
1 Introduction Test on Cyclic Lateral Loaded Piles in Sand Christian Linde Olsen Griffith University, Faculty of Engineering and Information Technology, Gold Coast Campus. Abstract The following paper
More informationEFFECT OF VARIOUS PARAMETERS ON DYNAMIC PROPERTIES OF BABOLSAR SAND BY CYCLIC SIMPLE SHEAR DEVICE
4 th International Conference on Earthquake Geotechnical Engineering June 25-28, 27 Paper No. 274 EFFECT OF VARIOUS PARAMETERS ON DYNAMIC PROPERTIES OF BABOLSAR SAND BY CYCLIC SIMPLE SHEAR DEVICE Fardin
More informationLesson 25. Static Pile Load Testing, O-cell, and Statnamic. Reference Manual Chapter 18
Lesson 25 Static Pile Load Testing, O-cell, and Statnamic Reference Manual Chapter 18 STATIC LOAD TESTING Most accurate method to determine static pile capacity Perform at design or construction stage
More informationSensors and transducers
Sensors and transducers Measurement is an important subsystem of a mechatronics system. Its main function is to collect the information on system status and to feed it to the micro-processor(s) for controlling
More informationSamantha Ramirez, MSE. Stress. The intensity of the internal force acting on a specific plane (area) passing through a point. F 2
Samantha Ramirez, MSE Stress The intensity of the internal force acting on a specific plane (area) passing through a point. Δ ΔA Δ z Δ 1 2 ΔA Δ x Δ y ΔA is an infinitesimal size area with a uniform force
More informationGeotechnical Properties of Soil
Geotechnical Properties of Soil 1 Soil Texture Particle size, shape and size distribution Coarse-textured (Gravel, Sand) Fine-textured (Silt, Clay) Visibility by the naked eye (0.05 mm is the approximate
More informationSeismic Evaluation of Tailing Storage Facility
Australian Earthquake Engineering Society 2010 Conference, Perth, Western Australia Seismic Evaluation of Tailing Storage Facility Jonathan Z. Liang 1, David Elias 2 1 Senior Geotechnical Engineer, GHD
More informationTransducers. EEE355 Industrial Electronics
Transducers EEE355 Industrial Electronics 1 Terminology Transducers convert one form of energy into another Sensors/Actuators are input/output transducers Sensors can be passive (e.g. change in resistance)
More informationThe effect of restraints type on the generated stresses in gantry crane beam
The effect of restraints type on the generated stresses in gantry crane beam Leszek Sowa 1,*, Wiesława Piekarska 1, Tomasz Skrzypczak 1, Paweł Kwiatoń 1 1 Czestochowa University of Technology, Institute
More informationThe theories to estimate lateral earth pressure due to a strip surcharge loading will
Chapter LITERATURE REVIEW The theories to estimate lateral earth pressure due to a strip surcharge loading will be introduced in this chapter. Commonly geotechnical engineers apply the equations suggested
More informationUNIVERSITY OF SASKATCHEWAN ME MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich
UNIVERSITY OF SASKATCHEWAN ME 313.3 MECHANICS OF MATERIALS I FINAL EXAM DECEMBER 13, 2008 Professor A. Dolovich A CLOSED BOOK EXAMINATION TIME: 3 HOURS For Marker s Use Only LAST NAME (printed): FIRST
More informationModule 2 Mechanics of Machining. Version 2 ME IIT, Kharagpur
Module 2 Mechanics of Machining Lesson 10 Dynamometers for measuring cutting forces Instructional objectives At the end of this lesson, the students would be able to (i) (ii) (iii) (iv) show the general
More informationDynamic Response of EPS Blocks /soil Sandwiched Wall/embankment
Proc. of Second China-Japan Joint Symposium on Recent Development of Theory and Practice in Geotechnology, Hong Kong, China Dynamic Response of EPS Blocks /soil Sandwiched Wall/embankment J. C. Chai 1
More informationField & Laboratory Evaluation of the Portable Falling Weight Deflectometer (PFWD) NETC Project No. 00-4
Field & Laboratory Evaluation of the Portable Falling Weight Deflectometer (PFWD) NETC Project No. 00-4 Principal Investigators: Dana N. Humphrey, Ph.D., P.E. Professor & Chairperson, Department of Civil
More informationLong-Term Strength Degradation Testing of DGR-3 and DGR-4 Core
Technical Report Title: Document ID: Authors: Long-Term Strength Degradation Testing of DGR-3 and DGR-4 Core TR-08-36 B. Gorski, T. Anderson and B. Conlon CANMET Mining and Mineral Sciences Laboratories,
More informationSubject Index. STP1026-EB/Nov. 1989
STP1026-EB/Nov. 1989 Subject Index A AASHTO and Unified Soil Classification System, 686, 687 (table) 1986 AASHTO Guide for Design of Pavement Structures, 64, 683-690 AASHTO Test Method T 274-82,640-643,
More informationProf. Dr.-Ing. Martin Achmus Institute of Soil Mechanics, Foundation Engineering and Waterpower Engineering. Monopile design
Prof. Dr.-Ing. Martin Achmus Institute of Soil Mechanics, Foundation Engineering and Waterpower Engineering Monopile design Addis Ababa, September 2010 Monopile design Presentation structure: Design proofs
More informationSTRESSES IN SOIL MASS
CHAPTER 4 Prepared by: Dr. Farouk Majeed Muhauwiss Civil Engineering Department College of Engineering Tikrit University STRESSES IN SOIL MASS 4.1 DEFIFINTIONS VERTTICAL STRESS Occurs due to internal or
More informationSMALL-DIAMETER TDR CABLES FOR MEASURING DISPLACEMENT IN PHYSICAL SOIL MODELS
SMALL-DIAMETER TDR CABLES FOR MEASURING DISPLACEMENT IN PHYSICAL SOIL MODELS C.M. McAlister 1 and C.E. Pierce 2 1 Graduate Research Assistant, Department of Civil and Environmental Engineering, University
More informationAN UNLOADING AND RELOADING STRESS-STRAIN MODEL FOR CONCRETE CONFINED BY TIE REINFORCEMENTS
AN UNLOADING AND RELOADING STRESS-STRAIN MODEL FOR CONCRETE CONFINED BY TIE REINFORCEMENTS Junichi SAKAI 1 And Kazuhiko KAWASHIMA SUMMARY This paper presents a series of uniaxial compressive loading tests
More informationUNIT I SIMPLE STRESSES AND STRAINS
Subject with Code : SM-1(15A01303) Year & Sem: II-B.Tech & I-Sem SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road 517583 QUESTION BANK (DESCRIPTIVE) UNIT I SIMPLE STRESSES
More informationPart 2. Sensor and Transducer Instrument Selection Criteria (3 Hour)
Part 2 Sensor and Transducer Instrument Selection Criteria (3 Hour) At the end of this chapter, you should be able to: Describe the definition of sensor and transducer Determine the specification of control
More informationInitial Stress Calculations
Initial Stress Calculations The following are the initial hand stress calculations conducted during the early stages of the design process. Therefore, some of the material properties as well as dimensions
More informationCHAPTER THREE SYMMETRIC BENDING OF CIRCLE PLATES
CHAPTER THREE SYMMETRIC BENDING OF CIRCLE PLATES * Governing equations in beam and plate bending ** Solution by superposition 1.1 From Beam Bending to Plate Bending 1.2 Governing Equations For Symmetric
More informationReciprocal of the initial shear stiffness of the interface K si under initial loading; reciprocal of the initial tangent modulus E i of the soil
Appendix F Notation a b B C c C k C N C s C u C wt C θ D r D 1 D 2 D 10 D 30 Reciprocal of the initial shear stiffness of the interface K si under initial loading; reciprocal of the initial tangent modulus
More information2. (a) Differentiate between rare metal thermocouples and base metal thermocouples.
Code No: R05410304 Set No. 1 1. (a) Distinguish between direct and indirect methods of measurement with suitable examples. (b) What are desired, modifying and interfering inputs for an instrumentation
More informationCanadian Geotechnical Journal SUBGRADE RESILIENT MODULUS PREDICTION FROM LIGHT WEIGHT DEFLECTOMETER
SUBGRADE RESILIENT MODULUS PREDICTION FROM LIGHT WEIGHT DEFLECTOMETER Journal: Manuscript ID cgj-2016-0062.r1 Manuscript Type: Article Date Submitted by the Author: 12-Jul-2016 Complete List of Authors:
More information