Bending and Shear in Beams
|
|
- Dylan Wilcox
- 6 years ago
- Views:
Transcription
1 Bending and Shear in Beams Lecture 3 5 th October 017 Contents Lecture 3 What reinforcement is needed to resist M Ed? Bending/ Flexure Section analysis, singly and doubly reinforced Tension reinforcement, A s neutral axis depth limit & K x = Neutral axis depth Compression reinforcement, A s Flexure Worked Example Doubly reinforced What shear links are needed to resist V Ed? Shear in Beams - Variable strut method Beam Examples Bending, Shear & High shear Exercise - Design a beam for flexure and shear EC Webinar Autumn 017 Lecture 3/1
2 Bending/ Flexure Section Design: Bending In principal flexural design is generally the same as BS8110 EC presents the principles only Design manuals will provide the standard solutions for basic design cases. There are modifications for high strength concrete ( f ck > 50 MPa ) Note: TCC How to guide equations and equations used on this course are based on a concrete f ck 50 MPa EC Webinar Autumn 017 Lecture 3/
3 Section Analysis to determine Tension & Compression Reinforcement EC contains information on: Information needed to derive equations Concrete stress blocks to find A s for a given M Ed. Reinforcement stress/strain curves The maximum depth of the neutral axis, x. This depends on the moment redistribution ratio used, δ. The design stress for concrete, f cd and reinforcement, f yd In EC there are no equations to determine A s, tension steel, and A s, compression steel, for a given ultimate moment, M, on a section. Equations, similar to those in BS 8110, are derived in the following slides. As in BS8110 the terms K and K are used: M K = bd f ck If K > K Compression steel required Value of K for maximum value of M with no compression steel and when x is at its maximum value. Rectangular Concrete Stress Block EC: Cl 3.1.7, Fig 3.5 Ac εcu3 η fcd x λx Fc Concise: Fig 6.1 d Parabolic stress block As Fs f ck 50 MPa εs 50 < f ck 90 MPa λ 0.8 = 0.8 (f ck 50)/400 η 1.0 = 1,0 (f ck 50)/00 f cd = α cc f ck /γ c = 0.85 f ck /1.5 f ck λ η For f ck 50 MPa failure concrete strain, ε cu, = EC Webinar Autumn 017 Lecture 3/3
4 Reinforcement Design Stress/Strain Curve EC: Cl 3..7, Fig 3.8 σ Idealised kfyk In UK f yk = 500 MPa fyk kfyk/γs fyd = fyk/γs f yd = f yk /γ s = 500/1.15 = 435 MPa Design E s may be taken to be 00 GPa Steel yield strain = f yd /E s (ε s at yield point) = 435/00000 = 0.00 fyd/ Es ε ud ε uk ε At failure concrete strain is for f ck 50 MPa. If x/d is 0.6 steel strain is and this is past the yield point. Design steel stress is 435 MPa if neutral axis, x, is less than 0.6d. Analysis of a singly reinforced beam EC: Cl Design equations can be derived as follows: b M For grades of concrete up to C50/60, ε cu = , η = 1 and λ = 0.8. f cd = 0.85f ck/1.5 f yd = f yk/1.15 = 0.87 f yk F c = (0.85 f ck / 1.5) b (0.8 x) = f ck b x For no compression F st = 0.87A s f yk reinforcement F sc = 0 Methods to find As: Iterative, trial and error method simple but not practical Direct method of calculating z, the lever arm, and then A s EC Webinar Autumn 017 Lecture 3/4
5 Analysis of a singly reinforced beam Determine A s Iterative method b M For horizontal equilibrium F c = F st f ck b x = 0.87A s f yk Guess A s Solve for x z = d x M = F c z Stop when design applied BM, M Ed M Analysis of a singly reinforced beam Determine A s Direct method Take moments about the centre of the tension force, F st : M = F c z = f ck b x z (1) (1) Now z = d x x =.5(d - z) M = f ck b.5(d - z) z = (f ck b z d - f ck b z ) M Let K = M / (f ck b d ) K M f bd f bdz = f bd ck ck = - ck ck ck (K may be considered as the normalised bending resistance) 0 = [(z/d) (z/d)] + K 0 = (z/d) (z/d) K f bz f bd EC Webinar Autumn 017 Lecture 3/5
6 0 = (z/d) (z/d) K Solving the quadratic equation: z/d = [1 + (1-3.53K) 0.5 ]/ z = d [ 1 + (1-3.53K) 0.5 ]/ M The lever arm for an applied moment is now known Quadratic formula Higher Concrete Strengths f ck 50MPa z = d[1+ (1 3.59K )]/ Normal strength f ck = 60MPa z = d[1+ ( K )]/ f ck = 70MPa z = d[1+ (1 3.9K )]/ f ck = 80MPa z = d[1+ (1 4.15K )]/ f ck = 90MPa z = d[1+ (1 4.41K )]/ EC Webinar Autumn 017 Lecture 3/6
7 Tension steel, A s Concise: 6..1 Take moments about the centre of the compression force, F c : M = F st z = 0.87A s f yk z Rearranging A s = M /(0.87 f yk z) The required area of reinforcement can now be found using three methods: a) calculated using these expressions b) obtained from Tables of z/d (eg Table 5 of How to beams or Concise Table 15.5, see next slide) c) obtained from graphs (eg from the Green Book or Fig B.3 in Concrete Buildings Scheme Design Manual, next slide but one) Design aids for flexure - method (b) K = M / (f ck b d ) Concise: Table Traditionally z/d was limited to 0.95 max to avoid issues with the quality of covercrete. Normal tables and charts are only valid up to C50/60 EC Webinar Autumn 017 Lecture 3/7
8 Design aids for flexure- method (c) TCC Concrete Buildings Scheme Design Manual, Fig B.3 K = M / (f ck b d ) 1.4 Design chart for singly reinforced beam Maximum neutral axis depth EC: Cl 5.5 Linear elastic analysis with limited redistribution Concise: Table 6.1 According to Cl 5.5(4) the depth of the neutral axis is limited, viz: δ k 1 + k x u /d where k 1 = 0.4 k = / ε cu = / = 1 x u = depth to NA after redistribution δ = Redistributed Bending Moment Elastic Bending Moment = Redistribution ratio x u d (δ - 0.4) Therefore there are limits on K and this limit is denoted K For K > K Compression steel needed EC Webinar Autumn 017 Lecture 3/8
9 K and Beams with Compression Reinforcement, A s The limiting value for K (denoted K ) can be calculated as follows: As before M = f ck b x z (1) and K = M / (f ck b d ) & z = d 0.4 x & x u = d (δ 0.4) Substituting x u for x in eqn (1) and rearranging: M = b d f ck (0.6 δ 0.18 δ - 0.1) Concise: 6..1 K = M /(b d f ck ) = (0.6 δ 0.18 δ - 0.1) Min δ = 0.7 (30% redistribution). Steel to be either Class B or C for 0% to 30% redistribution. Some engineers advocate taking x/d < 0.45, and K < It is often considered good practice to limit the depth of the neutral axis to avoid over-reinforcement to ensure a ductile failure. This is not an EC requirement and is not accepted by all engineers. Note: For plastic analysis x u /d must be 0.5 for normal strength concrete, EC cl 5.6. (). Compression steel, A s EC: Fig 3.5 Concise: 6..1 For K > K compression reinforcement A s is required. A s can be calculated by taking moments about the centre of the tension force: Rearranging M = K f ck b d f yk A s (d - d ) A s = (K - K ) f ck b d / (0.87 f yk (d - d )) EC Webinar Autumn 017 Lecture 3/9
10 Tension steel, A s for beams with Compression Reinforcement, The concrete in compression is at its design capacity and is reinforced with compression reinforcement. So now there is an extra force: F sc = 0.87A s f yk The area of tension reinforcement can now be considered in two parts. The first part balances the compressive force in the concrete (with the neutral axis at x u ). The second part balances the force in the compression steel. The area of reinforcement required is therefore: A s = K f ck b d /(0.87 f yk z) + A s where z is calculated using K instead of K Design Flowchart The following flowchart outlines the design procedure for rectangular beams with concrete classes up to C50/60 and grade 500 reinforcement Carry out analysis to determine design moments (M) Determine K and K from: M K = & K' = 0.6δ 0.18δ 0. 1 bd f ck Note: δ =1.0 means no redistribution and δ = 0.8 means 0% moment redistribution. Yes No Is K K? δ K No compression steel needed singly reinforced Compression steel needed - doubly reinforced It is often recommended in the UK that K is limited to to ensure ductile failure EC Webinar Autumn 017 Lecture 3/10
11 Flow Chart for Singly-reinforced Beam/Slab K K Calculate lever arm z from: d z = (Or look up z/d from table or from chart.) [ K ] 0.95d * * A limit of 0.95d is considered good practice, it is not a requirement of Eurocode. Calculate tension steel required from: A s = M f z yd Check minimum reinforcement requirements: 0.6f b d A ctm t s,min bt d f yk (Cl ) Exp. (9.1N) Check max reinforcement provided A s,max 0.04A c (Cl ) Check min spacing between bars > Ø bar > 0 > A gg + 5 Check max spacing between bars Minimum Reinforcement Area EC: Cl , Exp. 9.1N The minimum area of reinforcement for beams and slabs is given by: 0.6f b d A ctm t s,min b f yk t d EC Webinar Autumn 017 Lecture 3/11
12 Flow Chart for Doubly- Reinforced Beam K > K Calculate lever arm z from: d z = [ K' ] Calculate excess moment from: M ' = bd f ( K K' ) ck Calculate compression steel required from: M' As = f d d yd ( ) Calculate tension steel required from: K' fck bd As = + A f z yd s Check max reinforcement provided A s,max 0.04A c (Cl ) Check min spacing between bars > Ø bar > 0 > A gg + 5 Flexure Worked Example (Doubly reinforced) EC Webinar Autumn 017 Lecture 3/1
13 Worked Example 1 Design the section below to resist a sagging moment of 370 knm assuming 15% moment redistribution (i.e. δ = 0.85). Take f ck = 30 MPa and f yk = 500 MPa. d Worked Example 1 Initially assume 3 mm φ for tension reinforcement with 30 mm nominal cover to the link all round (allow 10 mm for link) and assume 0mm φ for compression reinforcement. = 50 d = h c nom - Ø link - 0.5Ø = = 444 mm = 444 d = c nom + Ø link + 0.5Ø = = 50 mm EC Webinar Autumn 017 Lecture 3/13
14 Worked Example 1 K' = δ K M K = bd f ck = = > K' provide compression steel [ '] d z = K 444 = = 363 mm [ ] Worked Example 1 M ' = bd f ck ( K K' ) = ( ) 10 = 7.7 knm A s = f yd M ' ( d d ) x 10 = 435 (444 50) = 44 mm 6 M M ' As = + A f z yd = 307 mm s ( ) 10 = K ' bd f = f z 6 yd + 44 ck + A s EC Webinar Autumn 017 Lecture 3/14
15 Worked Example 1 Provide H0 for compression steel = 68mm (44 mm req d) and 3 H3 tension steel = 41mm (307 mm req d) By inspection does not exceed maximum area (0.04 A c ) or maximum spacing of reinforcement rules (cracking see week 6 notes) Check minimum spacing, assuming H10 links Space between bars = ( x - 10 x - 3 x 3)/ = 6 mm > 3 mm* OK * EC Cl 8. () Spacing of bars for bond: Clear distance between bars > Ф bar > 0 mm > Agg + 5 mm Poll Q1: Design reinforcement strength, f yd For H type bar reinforcement what is f yd? a. 435 MPa b. 460 MPa c. 476 MPa d. 500 MPa EC Webinar Autumn 017 Lecture 3/15
16 Poll Q: Neutral axis depth, x A beam section has an effective depth of 500mm and the ultimate elastic bending moment has been reduced by 30%. What is the maximum depth of the neutral axis, x u? a. 150 mm b. 50 mm c. 300 mm d. 450 mm Shear in Beams Variable strut method EC Webinar Autumn 017 Lecture 3/16
17 Shear EC: Cl 6.., 6..3, 6.4 Concise: 7., 7.3, 8.0 There are three approaches to designing for shear: When shear reinforcement is not required e.g. slabs, week 5 Shear check uses V Rd,c When shear reinforcement is required e.g. Beams Variable strut method is used to check shear in beams Strut strength check using V Rd,max Links strength using V Rd,s Punching shear requirements e.g. flat slabs, week 5 The maximum shear strength in the UK should not exceed that of class C50/60 concrete. Cl 3.1. () P and NA. Shear in Beams EC: Cl 6..3 Concise: 7.3 Shear design is different from BS8110. EC uses the variable strut method to check a member with shear reinforcement. Definitions: V Ed V Rd,c V Rd,s - Applied shear force. For predominately UDL, shear may be checked at d from face of support Resistance of member without shear reinforcement - Resistance of member governed by the yielding of shear reinforcement V Rd,max - Resistance of member governed by the crushing of compression struts Whilst Eurocode deals in Resistances (capacities), V Rd,c,V Rd,s,V Rd,max and Effect of actions, V Ed in kn, in practice, it is often easier to consider shear strengths v Rd, v Rd,max and shear stresses, v Ed, in MPa. EC Webinar Autumn 017 Lecture 3/17
18 Members Requiring Shear Reinforcement EC: 6..3(1) Concise: Fig 7.3 compression chord compression chord strut F cd V(cot θ - cotα ) d α θ V ½ z ½ z z = 0.9d N V M s shear reinforcement tension chord F td α θ z angle between shear reinforcement and the beam axis Normally links are vertical. α = 90 o and cot α is zero angle between the concrete compression strut and the beam axis inner lever arm. In the shear analysis of reinforced concrete without axial force, the approximate value z = 0,9d may normally be used. Members Requiring Shear Reinforcement EC: 6..3(1) Concise: Fig 7.3 b w A sw is the minimum width Area of the shear reinforcement f ywd design yield strength = f yk /1.15 f cd design compressive strength = α cc f ck /1.5 = f ck /1.5 (α cc = 1.0 for shear) α cw = 1.0 Coefficient for stress in compression chord ν 1 strength reduction factor concrete cracked in shear ν 1 = ν = 0.6(1-f ck /50) Exp (6.6N) EC Webinar Autumn 017 Lecture 3/18
19 Strut Inclination Method EC: Equ. 6.8 & 6.9 for Vertical links Equ 6.9 αcw bw z ν 1 fcd VRd,max = cotθ + tanθ V Ed Strut angle limits 1.8 < θ < 45 Cot θ =.5 Cot θ = 1 V = Rd, s A sw s Equ 6.8 z fywd cotθ Eurocode vs BS8110: Shear Safer Shear reinforcement density A s f yd /s BS8110: V R = V C + V S Eurocode : V Rmax Fewer links (but more critical) Test results V R Minimum links Shear Strength, V R EC Webinar Autumn 017 Lecture 3/19
20 Shear Design: Links Variable strut method allows a shallower strut angle hence activating more links. As strut angle reduces concrete stress increases Min curtailment for 45 o strut V high s V low z d θ z d x Angle = 45 V carried on 3 links Max angle - max shear resistance x Angle = 1.8 V carried on 6 links Min strut angle - Minimum links Shear Resistance of Sections with Vertical Shear Reinforcement Concise: V s V x Basic equations shear reinforcement control Exp (6.8) V Rd,s = A sw z f ywd cot θ /s 1 cotθ,5 concrete strut control Exp (6.9) z θ = 45 θ = 1.8 V Rd,max = α cw z b w ν 1 f cd /(cotθ + tanθ) d x θ z where: f ywd = f yk /1.15 = 0.5 z b w ν 1 f cd sin θ d ν 1 = ν = 0.6(1-f ck /50) α cw = 1.0 EC Webinar Autumn 017 Lecture 3/0
21 Shear links EC: Cl 6..3 Equation 6.9 is first used to determine the strut angle θ and then equation 6.8 is used to find the shear link area, A sw, and spacing s. Equation 6.9 gives V Rd,max values for a given strut angle θ e.g. when cot θ =.5 (θ = 1.8 ) Equ 6.9 becomes V Rd,max = b w z f ck (1 - f ck /50) or in terms of stress: v Rd,max = f ck (1 - f ck /50) Values are in the middle column of the table. Re-arranging equation 6.9 to find θ: θ = 0.5 sin -1 [v Rd /(0.0 f ck (1 - f ck /50))] Suitable shear links are found from equation 6.8: A sw /s = v Ed b w /( f ywd cot θ) v Rd, cot θ v Rd, cot θ f ck =.5 = v Rd,max values, MPa, for cot θ = 1.0 and.5 EC Shear Flow Chart for vertical links Determine v Ed where: v Ed = design shear stress [v Ed = V Ed /(b w z) = V Ed /(b w 0.9d)] Determine the concrete strut capacity v Rd when cot θ =.5 v Rdcot θ =.5 = 0.138f ck (1-f ck /50) (or look up from table) Is v Rd,cot θ =.5 > v Ed? No Is v Rd,cot θ = 1.0 > v Ed? No Re-size Yes (cot θ =.5) Calculate area of shear reinforcement: A sw /s = v Ed b w /(f ywd cot θ) Check minimum area, cl 9..: A sw /s b w ρ w,min ρ w,min = (0.08 f ck )/f yk Yes (cot θ > 1.0) Determine θ from: θ = 0.5 sin -1 [(v Ed /(0.0f ck (1-f ck /50))] Check maximum spacing of shear reinforcement, cl 9..: s l,max = s t,max = 0.75 d EC Webinar Autumn 017 Lecture 3/1
22 Design aids for shear Concise Fig 15.1 a) V Ed = 4.3 MPa A sw /s = 5.3 per m width Short Shear Spans with Direct Strut Action EC: 6..3 d d a v a v Where a v d the applied shear force, V Ed, for a point load (eg, corbel, pile cap etc) may be reduced by a factor a v /d where 0.5d a v d provided: The longitudinal reinforcement is fully anchored at the support. Only that shear reinforcement provided within the central 0.75a v is included in the resistance. Note: see PD6687-1:010 Cl.14 for more information EC Webinar Autumn 017 Lecture 3/
23 Beam examples Bending, Shear and High Shear Beam Example 1 G k = 75 kn/m, Q k = 50 kn/m, assume no redistribution and use EC0 equation 6.10 to calculate ULS loads. 8 m Nominal cover = 40mm to each face f ck = 30 Determine the flexural and shear reinforcement required (try 10mm links and 3mm main steel) EC Webinar Autumn 017 Lecture 3/3
24 Beam Example 1 Bending ULS load per m = (75 x x 1.5) = M ult = x 8 /8 = 1410 knm How to Ch 4 - Beams d = / = 934 M K = bd = f = ck 0.10 K = 0.08 K < K No compression reinforcement required 934 [ K ] = [ x 0.10] = 8 0. d d z = 95 6 M 1410 x 10 A = = = 3943 mm s f z 435 x 8 yd Provide 5 H3 (401 mm ) Beam Example 1 Shear Shear force, V Ed = x 8/ = 705 kn Shear stress: (We could take 505 d from face) v Ed = V Ed /(b w 0.9d) = 705 x 10 3 /(450 x 0.9 x 934) = 1.68 MPa v Rdcot θ =.5 = 3.64 MPa f ck v Rd, cot θ =.5 v Rd, cot θ = 1.0 v Rdcot θ =.5 > v Ed cot θ =.5 A sw /s = v Ed b w /(f ywd cot θ) A sw /s = 1.68 x 450 /(435 x.5) A sw /s = 0.70 mm Try H10 links with 4 legs. A sw = 314 mm s < 314 /0.70 = 448 mm provide H10 links at 450 mm spacing EC Webinar Autumn 017 Lecture 3/4
25 Beam Example 1 Provide 5 H3 (401) mm ) with H10 links at 450 mm spacing Max spacing is 0.75d = 934 x 0.75 = 700 mm Beam Example High shear UDL not dominant Find the minimum area of shear reinforcement required to resist the design shear force using EC. Assume that: f ck = 30 MPa and f yd = 500/1.15 = 435 MPa EC Webinar Autumn 017 Lecture 3/5
26 Beam Example High shear Find the minimum area of shear reinforcement required to resist the design shear force using EC. fck fyd = 30 MPa and = 435 MPa Shear stress: v Ed = V Ed /(b w 0.9d) = 31.5 x 10 3 /(140 x 0.9 x 500) = 4.96 MPa v Rdcot θ =.5 = 3.64 MPa v Rdcot θ = 1.0 = 5.8 MPa v Rdcot θ =.5 < v Ed < v Rdcot θ = > cot θ > 1.0 Calculate θ f ck v Rd, cot θ =.5 v Rd, cot θ = Beam Example High shear Calculate θ θ = 0.5 sin θ = 0.5 sin = 35.0 cot θ = f ck ved (1 f ck x 30 / 50) ( 1-30 / 50) A sw /s = v Ed b w /(f ywd cot θ ) A sw /s = 4.96 x 140 /(435 x 1.43) A sw /s = 1.1 mm Try H10 links with legs. A sw = 157 mm s < 157 /1.1 = 140 mm provide H10 links at 15 mm spacing EC Webinar Autumn 017 Lecture 3/6
27 Exercise Lecture 3 Design a beam for flexure and shear Beam Exercise Flexure & Shear G k = 10 kn/m, Q k = 6.5 kn/m (Use EC0 eq. 6.10) 8 m 450 Nominal cover = 35 mm to each face f ck = 30MPa Design the beam in flexure and shear 300 EC Webinar Autumn 017 Lecture 3/7
28 Aide memoire Exp (6.10) Remember this from the first week? Or Concise Table 15.5 Workings:- Load, M ult, d, K, K, (z/d,) z, A s, V Ed, A sw /s Φ mm Area, mm EC Webinar Autumn 017 Lecture 3/8
29 Working space Working space EC Webinar Autumn 017 Lecture 3/9
30 Working space End of Lecture 3 pgregory@concretecentre.com EC Webinar Autumn 017 Lecture 3/30
Detailing. Lecture 9 16 th November Reinforced Concrete Detailing to Eurocode 2
Detailing Lecture 9 16 th November 2017 Reinforced Concrete Detailing to Eurocode 2 EC2 Section 8 - Detailing of Reinforcement - General Rules Bar spacing, Minimum bend diameter Anchorage of reinforcement
More information- Rectangular Beam Design -
Semester 1 2016/2017 - Rectangular Beam Design - Department of Structures and Material Engineering Faculty of Civil and Environmental Engineering University Tun Hussein Onn Malaysia Introduction The purposes
More informationPractical Design to Eurocode 2
Practical Design to Eurocode 2 The webinar will start at 12.30 (Any questions beforehand? use Questions on the GoTo Control Panel) Course Outline Lecture Date Speaker Title 1 21 Sep Jenny Burridge Introduction,
More information10/14/2011. Types of Shear Failure. CASE 1: a v /d 6. a v. CASE 2: 2 a v /d 6. CASE 3: a v /d 2
V V Types o Shear Failure a v CASE 1: a v /d 6 d V a v CASE 2: 2 a v /d 6 d V a v CASE 3: a v /d 2 d V 1 Shear Resistance Concrete compression d V cz = Shear orce in the compression zone (20 40%) V a =
More informationPractical Design to Eurocode 2. The webinar will start at 12.30
Practical Design to Eurocode 2 The webinar will start at 12.30 Course Outline Lecture Date Speaker Title 1 21 Sep Jenny Burridge Introduction, Background and Codes 2 28 Sep Charles Goodchild EC2 Background,
More informationAnnex - R C Design Formulae and Data
The design formulae and data provided in this Annex are for education, training and assessment purposes only. They are based on the Hong Kong Code of Practice for Structural Use of Concrete 2013 (HKCP-2013).
More informationDepartment of Mechanics, Materials and Structures English courses Reinforced Concrete Structures Code: BMEEPSTK601. Lecture no. 6: SHEAR AND TORSION
Budapest University of Technology and Economics Department of Mechanics, Materials and Structures English courses Reinforced Concrete Structures Code: BMEEPSTK601 Lecture no. 6: SHEAR AND TORSION Reinforced
More informationReinforced Concrete Structures
Reinforced Concrete Structures MIM 232E Dr. Haluk Sesigür I.T.U. Faculty of Architecture Structural and Earthquake Engineering WG Ultimate Strength Theory Design of Singly Reinforced Rectangular Beams
More informationCHAPTER 4. Design of R C Beams
CHAPTER 4 Design of R C Beams Learning Objectives Identify the data, formulae and procedures for design of R C beams Design simply-supported and continuous R C beams by integrating the following processes
More informationDesign of reinforced concrete sections according to EN and EN
Design of reinforced concrete sections according to EN 1992-1-1 and EN 1992-2 Validation Examples Brno, 21.10.2010 IDEA RS s.r.o. South Moravian Innovation Centre, U Vodarny 2a, 616 00 BRNO tel.: +420-511
More informationEurocode Training EN : Reinforced Concrete
Eurocode Training EN 1992-1-1: Reinforced Concrete Eurocode Training EN 1992-1-1 All information in this document is subject to modification without prior notice. No part of this manual may be reproduced,
More informationExample 2.2 [Ribbed slab design]
Example 2.2 [Ribbed slab design] A typical floor system of a lecture hall is to be designed as a ribbed slab. The joists which are spaced at 400mm are supported by girders. The overall depth of the slab
More informationDesign of AAC wall panel according to EN 12602
Design of wall panel according to EN 160 Example 3: Wall panel with wind load 1.1 Issue Design of a wall panel at an industrial building Materials with a compressive strength 3,5, density class 500, welded
More informationDESIGN OF STAIRCASE. Dr. Izni Syahrizal bin Ibrahim. Faculty of Civil Engineering Universiti Teknologi Malaysia
DESIGN OF STAIRCASE Dr. Izni Syahrizal bin Ibrahim Faculty of Civil Engineering Universiti Teknologi Malaysia Email: iznisyahrizal@utm.my Introduction T N T G N G R h Flight Span, L Landing T = Thread
More informationLecture-03 Design of Reinforced Concrete Members for Flexure and Axial Loads
Lecture-03 Design of Reinforced Concrete Members for Flexure and Axial Loads By: Prof. Dr. Qaisar Ali Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk www.drqaisarali.com Prof.
More informationO Dr Andrew Bond (Geocentrix)
DECODING EUROCODES 2 + 7: DESIGN SG OF FOUNDATIONS O Dr Andrew Bond (Geocentrix) Outline of talk April 2010: the death of British Standards? UK implementation of Eurocodes Verification of strength: limit
More informationCE5510 Advanced Structural Concrete Design - Design & Detailing of Openings in RC Flexural Members-
CE5510 Advanced Structural Concrete Design - Design & Detailing Openings in RC Flexural Members- Assoc Pr Tan Kiang Hwee Department Civil Engineering National In this lecture DEPARTMENT OF CIVIL ENGINEERING
More informationJob No. Sheet No. Rev. CONSULTING Engineering Calculation Sheet. Member Design - Reinforced Concrete Beam BS8110 v Member Design - RC Beam XX
CONSULTING Engineering Calculation Sheet E N G I N E E R S Consulting Engineers jxxx 1 Effects From Structural Analysis Design axial force, F (tension -ve and compression +ve) (ensure < 0.1f cu b w h 0
More informationCRACK FORMATION AND CRACK PROPAGATION INTO THE COMPRESSION ZONE ON REINFORCED CONCRETE BEAM STRUCTURES
S. Kakay et al. Int. J. Comp. Meth. and Exp. Meas. Vol. 5 No. (017) 116 14 CRACK FORMATION AND CRACK PROPAGATION INTO THE COMPRESSION ZONE ON REINFORCED CONCRETE BEAM STRUCTURES SAMDAR KAKAY DANIEL BÅRDSEN
More informationLecture-04 Design of RC Members for Shear and Torsion
Lecture-04 Design of RC Members for Shear and Torsion By: Prof. Dr. Qaisar Ali Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk www.drqaisarali.com 1 Topics Addressed Design of
More informationJob No. Sheet No. Rev. CONSULTING Engineering Calculation Sheet
E N G I N E E R S Consulting Engineers jxxx 1 Material Properties Characteristic strength of concrete, f cu ( 60N/mm 2 ; HSC N/A) 35 N/mm 2 OK Yield strength of longitudinal steel, f y 460 N/mm 2 Yield
More informationConcise Eurocode 2 25 February 2010
Concise Eurocode 2 25 February 2010 Revisions required to Concise Eurocode 2 (Oct 06 edition) due to revisions in standards, notably Amendment 1 to NA to BS EN 1992-1-1:2004 dated Dec 2009, and interpretations.
More informationNAGY GYÖRGY Tamás Assoc. Prof, PhD
NAGY GYÖRGY Tamás Assoc. Prof, PhD E mail: tamas.nagy gyorgy@upt.ro Tel: +40 256 403 935 Web: http://www.ct.upt.ro/users/tamasnagygyorgy/index.htm Office: A219 SIMPLE SUPORTED BEAM b = 15 cm h = 30 cm
More informationTower Cranes & Foundations The Interface & CIRIA C654 Stuart Marchand C.Eng. FICE FIStructE Director Wentworth House Partnership
Tower Cranes & Foundations The Interface & CIRIA C654 Stuart Marchand C.Eng. FICE FIStructE Director Wentworth House Partnership EXAMPLES OF TOWER CRANE FOUNDATION TYPES Rail mounted Pad Base Piled Base
More informationCivil Engineering Design (1) Design of Reinforced Concrete Columns 2006/7
Civil Engineering Design (1) Design of Reinforced Concrete Columns 2006/7 Dr. Colin Caprani, Chartered Engineer 1 Contents 1. Introduction... 3 1.1 Background... 3 1.2 Failure Modes... 5 1.3 Design Aspects...
More informationConcrete and Masonry Structures 1 Office hours
Concrete and Masonry Structures 1 Petr Bílý, office B731 http://people.fsv.cvut.cz/www/bilypet1 Courses in English Concrete and Masonry Structures 1 Office hours Credit receiving requirements General knowledge
More informationSeismic Design, Assessment & Retrofitting of Concrete Buildings. fctm. h w, 24d bw, 175mm 8d bl, 4. w 4 (4) 2 cl
Seismic Design, Assessment & Retroitting o Concrete Buildings Table 5.1: EC8 rules or detailing and dimensioning o primary beams (secondary beams: as in DCL) DC H DCM DCL critical region length 1.5h w
More informationDesign of Reinforced Concrete Beam for Shear
Lecture 06 Design of Reinforced Concrete Beam for Shear By: Prof Dr. Qaisar Ali Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk 1 Topics Addressed Shear Stresses in Rectangular
More informationEXAMPLE CALCULATIONS DTF / DTS
MEMO 830 DTF / DTS EXAMPLE CALCULATIONS DESIGN Dato: Siste rev.: Dok. nr.: 19.09.013 5.05.016 K4-10/30E Sign.: Sign.: Control: sss ps CONTENT EXAMPLE CALCULATIONS DTF / DTS EXAMPLE CALCULATIONS DTF / DTS...
More informationFlexure: Behavior and Nominal Strength of Beam Sections
4 5000 4000 (increased d ) (increased f (increased A s or f y ) c or b) Flexure: Behavior and Nominal Strength of Beam Sections Moment (kip-in.) 3000 2000 1000 0 0 (basic) (A s 0.5A s ) 0.0005 0.001 0.0015
More informationStandardisation of UHPC in Germany
Standardisation of UHPC in Germany Part II: Development of Design Rules, University of Siegen Prof. Dr.-Ing. Ekkehard Fehling, University of Kassel 1 Overvie Introduction: Work of the Task Group Design
More information3.2 Reinforced Concrete Slabs Slabs are divided into suspended slabs. Suspended slabs may be divided into two groups:
Sabah Shawkat Cabinet of Structural Engineering 017 3. Reinforced Concrete Slabs Slabs are divided into suspended slabs. Suspended slabs may be divided into two groups: (1) slabs supported on edges of
More informationDesign of Reinforced Concrete Beam for Shear
Lecture 06 Design of Reinforced Concrete Beam for Shear By: Civil Engineering Department UET Peshawar drqaisarali@uetpeshawar.edu.pk Topics Addressed Shear Stresses in Rectangular Beams Diagonal Tension
More informationSeismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design
Seismic Pushover Analysis Using AASHTO Guide Specifications for LRFD Seismic Bridge Design Elmer E. Marx, Alaska Department of Transportation and Public Facilities Michael Keever, California Department
More informationJob No. Sheet No. Rev. CONSULTING Engineering Calculation Sheet
CONSULTING Engineering Calculation Sheet E N G I N E E R S Consulting Engineers jxxx 1 Effects From Structural Analysis Design axial force, F (tension -ve and compression +ve) (ensure < 0.1f cu b w h 0
More informationJob No. Sheet No. Rev. CONSULTING Engineering Calculation Sheet
CONSULTING Engineering Calculation Sheet jxxx 1 Effects From Structural Analysis Design axial force, F (tension -ve and compression +ve) (ensure < 0.1f cu b w h 0 kn OK Design shear force, V d 4223 kn
More informationDesign of a Multi-Storied RC Building
Design of a Multi-Storied RC Building 16 14 14 3 C 1 B 1 C 2 B 2 C 3 B 3 C 4 13 B 15 (S 1 ) B 16 (S 2 ) B 17 (S 3 ) B 18 7 B 4 B 5 B 6 B 7 C 5 C 6 C 7 C 8 C 9 7 B 20 B 22 14 B 19 (S 4 ) C 10 C 11 B 23
More informationPractical Design to Eurocode 2
Practical Design to Eurocode 2 The webinar will start at 12.30 (I m happy to field individual questions beforehand Use Questions on the shown Control Panel) Course Outline Lecture Date Speaker Title 1
More informationChapter 8. Shear and Diagonal Tension
Chapter 8. and Diagonal Tension 8.1. READING ASSIGNMENT Text Chapter 4; Sections 4.1-4.5 Code Chapter 11; Sections 11.1.1, 11.3, 11.5.1, 11.5.3, 11.5.4, 11.5.5.1, and 11.5.6 8.2. INTRODUCTION OF SHEAR
More informationDesign of a Balanced-Cantilever Bridge
Design of a Balanced-Cantilever Bridge CL (Bridge is symmetric about CL) 0.8 L 0.2 L 0.6 L 0.2 L 0.8 L L = 80 ft Bridge Span = 2.6 L = 2.6 80 = 208 Bridge Width = 30 No. of girders = 6, Width of each girder
More informationReinforced concrete structures II. 4.5 Column Design
4.5 Column Design A non-sway column AB of 300*450 cross-section resists at ultimate limit state, an axial load of 700 KN and end moment of 90 KNM and 0 KNM in the X direction,60 KNM and 27 KNM in the Y
More informationDESIGN AND DETAILING OF COUNTERFORT RETAINING WALL
DESIGN AND DETAILING OF COUNTERFORT RETAINING WALL When the height of the retaining wall exceeds about 6 m, the thickness of the stem and heel slab works out to be sufficiently large and the design becomes
More informationStrengthening of columns with FRP
with FRP Professor Dr. Björn Täljsten Luleå University of Technology Sto Scandinavia AB 9/12/2013 Agenda Case study Restrained transverse expansion (confinement) Circular and rectangular cross sections
More informationDesign of RC Sections with Single Reinforcement according to EC2-1-1 and the Rectangular Stress Distribution
Design of RC Sections with Single Reinforcement according to EC-1-1 and the Rectangular Stress Distribution Vagelis Plevris 1 and George Papazafeiropoulos 1 Department of Civil Engineering and Energy Technology
More informationSTRUCTURAL ANALYSIS CHAPTER 2. Introduction
CHAPTER 2 STRUCTURAL ANALYSIS Introduction The primary purpose of structural analysis is to establish the distribution of internal forces and moments over the whole part of a structure and to identify
More informationCONSULTING Engineering Calculation Sheet. Job Title Member Design - Reinforced Concrete Column BS8110
E N G I N E E R S Consulting Engineers jxxx 1 Job Title Member Design - Reinforced Concrete Column Effects From Structural Analysis Axial force, N (tension-ve and comp +ve) (ensure >= 0) 8000kN OK Major
More informationA Study on Behaviour of Symmetrical I-Shaped Column Using Interaction Diagram
A Study on Behaviour of Symmetrical I-Shaped Column Using Interaction Diagram Sudharma.V.S.Acharya 1, R.M. Subrahmanya 2, B.G. Naresh Kumar 3, Shanmukha Shetty 4, Smitha 5 P.G. Student, Department of Civil
More information9.5 Compression Members
9.5 Compression Members This section covers the following topics. Introduction Analysis Development of Interaction Diagram Effect of Prestressing Force 9.5.1 Introduction Prestressing is meaningful when
More informationLecture-08 Gravity Load Analysis of RC Structures
Lecture-08 Gravity Load Analysis of RC Structures By: Prof Dr. Qaisar Ali Civil Engineering Department UET Peshawar www.drqaisarali.com 1 Contents Analysis Approaches Point of Inflection Method Equivalent
More informationAssignment 1 - actions
Assignment 1 - actions b = 1,5 m a = 1 q kn/m 2 Determine action on the beam for verification of the ultimate limit state. Axial distance of the beams is 1 to 2 m, cross section dimensions 0,45 0,20 m
More informationEUROCODE EN SEISMIC DESIGN OF BRIDGES
Brussels, 18-20 February 2008 Dissemination of information workshop 1 EUROCODE EN1998-2 SEISMIC DESIGN OF BRIDGES Basil Kolias Basic Requirements Brussels, 18-20 February 2008 Dissemination of information
More informationDelhi Noida Bhopal Hyderabad Jaipur Lucknow Indore Pune Bhubaneswar Kolkata Patna Web: Ph:
Serial : IG1_CE_G_Concrete Structures_100818 Delhi Noida Bhopal Hyderabad Jaipur Lucknow Indore Pune Bhubaneswar Kolkata Patna Web: E-mail: info@madeeasy.in Ph: 011-451461 CLASS TEST 018-19 CIVIL ENGINEERING
More informationEinführung des EC2 in Belgien The introduction of EC2 in Belgium
Luc Taerwe 1 Einführung des EC2 in Belgien The introduction of EC2 in Belgium Luc Taerwe Univ.-Prof. Dr.-Ing. habil. Luc Taerwe - graduated as civil engineer at Ghent University (1975) where he also obtained
More informationThe European Concrete Platform ASBL, May 2008.
EUROCODE WORKED EXAMPLES EUROCODE WORKED EXAMPLES The European Concrete Platform ASBL, May 008. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted
More informationSlenderness Effects for Concrete Columns in Sway Frame - Moment Magnification Method (CSA A )
Slenderness Effects for Concrete Columns in Sway Frame - Moment Magnification Method (CSA A23.3-94) Slender Concrete Column Design in Sway Frame Buildings Evaluate slenderness effect for columns in a
More informationServiceability Limit States
Serviceability Limit States www.eurocode2.info 1 Outline Crack control and limitations Crack width calculations Crack width calculation example Crack width calculation problem Restraint cracking Deflection
More informationCivil Engineering Design (1) Analysis and Design of Slabs 2006/7
Civil Engineering Design (1) Analysis and Design of Slabs 006/7 Dr. Colin Caprani, Chartered Engineer 1 Contents 1. Elastic Methods... 3 1.1 Introduction... 3 1. Grillage Analysis... 4 1.3 Finite Element
More informationEvaluation of size effect on shear strength of reinforced concrete deep beams using refined strut-and-tie model
Sādhanā Vol. 7, Part, February, pp. 89 5. c Indian Academy of Sciences Evaluation of size effect on shear strength of reinforced concrete deep beams using refined strut-and-tie model GAPPARAO and R SUNDARESAN
More informationCHAPTER 4. ANALYSIS AND DESIGN OF COLUMNS
4.1. INTRODUCTION CHAPTER 4. ANALYSIS AND DESIGN OF COLUMNS A column is a vertical structural member transmitting axial compression loads with or without moments. The cross sectional dimensions of a column
More informationInteraction Diagram Dumbbell Concrete Shear Wall Unsymmetrical Boundary Elements
Interaction Diagram Dumbbell Concrete Shear Wall Unsymmetrical Boundary Elements Interaction Diagram - Dumbbell Concrete Shear Wall Unsymmetrical Boundary Elements Investigate the capacity for the irregular
More informationDEFORMATION CAPACITY OF OLDER RC SHEAR WALLS: EXPERIMENTAL ASSESSMENT AND COMPARISON WITH EUROCODE 8 - PART 3 PROVISIONS
DEFORMATION CAPACITY OF OLDER RC SHEAR WALLS: EXPERIMENTAL ASSESSMENT AND COMPARISON WITH EUROCODE 8 - PART 3 PROVISIONS Konstantinos CHRISTIDIS 1, Emmanouil VOUGIOUKAS 2 and Konstantinos TREZOS 3 ABSTRACT
More informationCHAPTER 6: ULTIMATE LIMIT STATE
CHAPTER 6: ULTIMATE LIMIT STATE 6.1 GENERAL It shall be in accordance with JSCE Standard Specification (Design), 6.1. The collapse mechanism in statically indeterminate structures shall not be considered.
More informationOUTCOME 1 - TUTORIAL 3 BENDING MOMENTS. You should judge your progress by completing the self assessment exercises. CONTENTS
Unit 2: Unit code: QCF Level: 4 Credit value: 15 Engineering Science L/601/1404 OUTCOME 1 - TUTORIAL 3 BENDING MOMENTS 1. Be able to determine the behavioural characteristics of elements of static engineering
More informationDESIGN OF DOWELS FOR SHEAR TRANSFER AT THE INTERFACE BETWEEN CONCRETE CAST AT DIFFERENT TIMES: A CASE STUDY
DESIGN OF DOWELS FOR SHEAR TRANSFER AT THE INTERFACE BETWEEN CONCRETE CAST AT DIFFERENT TIMES: A CASE STUDY Samayamanthree Mudiyanselage Premasiri Karunarathna 118614J Degree of Master of Engineering in
More informationRETAINING WALL ANALYSIS
GEODOMISI Ltd. Dr. Costas Sachpazis Consulting Company for Tel.: (+30) 20 523827, 20 57263 Fax.:+30 20 5746 Retaining wall Analysis & Design (EN997:2004 App'd by RETAINING WALL ANALYSIS In accordance with
More informationDIAGONAL TENSION RC BEAM without SHEAR REINFORCEMENT RC BEAM with WEB REINFORCEMENT KCI CODE PROVISION. ALTERNATIVE MODELS for SHEAR ANALYSIS
DIAGONAL TENSION RC BEAM without SHEAR REINFORCEMENT RC BEAM with WEB REINFORCEMENT KCI CODE PROVISION DEEP BEAMS ALTERNATIVE MODELS for SHEAR ANALYSIS SHEAR FRICTION DESIGN METHOD &DESIGN 447.327 Theory
More informationRETAINING WALL ANALYSIS
Retaining Wall Analysis Example (EN997:2004) GEODOMISI Ltd. Dr. Costas Sachpazis Consulting Company for Tel.: (+30) 20 523827, 20 57263 Fax.:+30 20 5746 App'd by RETAINING WALL ANALYSIS In accordance with
More informationChapter 2. Design for Shear. 2.1 Introduction. Neutral axis. Neutral axis. Fig. 4.1 Reinforced concrete beam in bending. By Richard W.
Chapter 2 Design for Shear By Richard W. Furlong 2.1 Introduction Shear is the term assigned to forces that act perpendicular to the longitudinal axis of structural elements. Shear forces on beams are
More informationExample 4.1 [Uni-axial Column Design] Solution. Step 1- Material Step 2-Determine the normalized axial and bending moment value
Example 4.1 [Uni-axial Column Design] 1. Design the braced short column to sustain a design load of 1100 KN and a design moment of 160KNm which include all other effects.use C5/30 and S460 class 1 works
More informationVTU EDUSAT PROGRAMME Lecture Notes on Design of Columns
VTU EDUSAT PROGRAMME 17 2012 Lecture Notes on Design of Columns DESIGN OF RCC STRUCTURAL ELEMENTS - 10CV52 (PART B, UNIT 6) Dr. M. C. Nataraja Professor, Civil Engineering Department, Sri Jayachamarajendra
More informationFLEXURAL ANALYSIS AND DESIGN METHODS FOR SRC BEAM SECTIONS WITH COMPLETE COMPOSITE ACTION
Journal of the Chinese Institute of Engineers, Vol. 31, No., pp. 15-9 (8) 15 FLEXURAL ANALYSIS AND DESIGN METHODS FOR SRC BEAM SECTIONS WITH COMPLETE COMPOSITE ACTION Cheng-Cheng Chen* and Chao-Lin Cheng
More informationJob No. Sheet No. Rev. CONSULTING Engineering Calculation Sheet. Member Design - RC Two Way Spanning Slab XX
CONSULTING Engineering Calculation Sheet E N G I N E E R S Consulting Engineers jxxx 1 Material Properties Characteristic strength of concrete, f cu ( 60N/mm 2 ; HSC N/A) 35 N/mm 2 OK Yield strength of
More informationThis document is downloaded from DR-NTU, Nanyang Technological University Library, Singapore.
This document is downloaded from DR-NTU, Nanyang Technological University Library, Singapore. Title Truss Model for Shear Strength of Structural Concrete Walls Author(s) Citation Chandra, Jimmy; Chanthabouala,
More informationSERVICEABILITY LIMIT STATE DESIGN
CHAPTER 11 SERVICEABILITY LIMIT STATE DESIGN Article 49. Cracking Limit State 49.1 General considerations In the case of verifications relating to Cracking Limit State, the effects of actions comprise
More informationModule 6. Shear, Bond, Anchorage, Development Length and Torsion. Version 2 CE IIT, Kharagpur
Module 6 Shear, Bond, Anchorage, Development Length and Torsion Lesson 15 Bond, Anchorage, Development Length and Splicing Instruction Objectives: At the end of this lesson, the student should be able
More informationTHEME IS FIRST OCCURANCE OF YIELDING THE LIMIT?
CIE309 : PLASTICITY THEME IS FIRST OCCURANCE OF YIELDING THE LIMIT? M M - N N + + σ = σ = + f f BENDING EXTENSION Ir J.W. Welleman page nr 0 kn Normal conditions during the life time WHAT HAPPENS DUE TO
More informationChapter. Materials. 1.1 Notations Used in This Chapter
Chapter 1 Materials 1.1 Notations Used in This Chapter A Area of concrete cross-section C s Constant depending on the type of curing C t Creep coefficient (C t = ε sp /ε i ) C u Ultimate creep coefficient
More informationAppendix J. Example of Proposed Changes
Appendix J Example of Proposed Changes J.1 Introduction The proposed changes are illustrated with reference to a 200-ft, single span, Washington DOT WF bridge girder with debonded strands and no skew.
More information6. Bending CHAPTER OBJECTIVES
CHAPTER OBJECTIVES Determine stress in members caused by bending Discuss how to establish shear and moment diagrams for a beam or shaft Determine largest shear and moment in a member, and specify where
More informationUNIT II SHALLOW FOUNDATION
Introduction UNIT II SHALLOW FOUNDATION A foundation is a integral part of the structure which transfer the load of the superstructure to the soil. A foundation is that member which provides support for
More informationCivil and Environmental Engineering. Title Shear strength of beams with loads close to supports. Sebastian Webb. Prof.
MASTER THESIS Master Civil and Environmental Engineering Title Shear strength of beams with loads close to supports Author Sebastian Webb Tutor Prof. Antonio Marí Speciality Structural Engineering Date
More information3.5 Analysis of Members under Flexure (Part IV)
3.5 Analysis o Members under Flexure (Part IV) This section covers the ollowing topics. Analysis o a Flanged Section 3.5.1 Analysis o a Flanged Section Introduction A beam can have langes or lexural eiciency.
More informationCHAPTER 4: BENDING OF BEAMS
(74) CHAPTER 4: BENDING OF BEAMS This chapter will be devoted to the analysis of prismatic members subjected to equal and opposite couples M and M' acting in the same longitudinal plane. Such members are
More informationCost optimum design of doubly reinforced high strength concrete T-beams
Scientia Iranica A (2017) 24(2), 476{486 Sharif University of Technology Scientia Iranica Transactions A: Civil Engineering www.scientiairanica.com Cost optimum design of doubly reinforced high strength
More informationREINFORCED CONCRETE DESIGN 1. Design of Column (Examples and Tutorials)
For updated version, please click on http://ocw.ump.edu.my REINFORCED CONCRETE DESIGN 1 Design of Column (Examples and Tutorials) by Dr. Sharifah Maszura Syed Mohsin Faculty of Civil Engineering and Earth
More informationFailure interaction curves for combined loading involving torsion, bending, and axial loading
Failure interaction curves for combined loading involving torsion, bending, and axial loading W M Onsongo Many modern concrete structures such as elevated guideways are subjected to combined bending, torsion,
More informationStructural Steelwork Eurocodes Development of A Trans-national Approach
Structural Steelwork Eurocodes Development of A Trans-national Approach Course: Eurocode Module 7 : Worked Examples Lecture 0 : Simple braced frame Contents: 1. Simple Braced Frame 1.1 Characteristic Loads
More informationPLATE GIRDERS II. Load. Web plate Welds A Longitudinal elevation. Fig. 1 A typical Plate Girder
16 PLATE GIRDERS II 1.0 INTRODUCTION This chapter describes the current practice for the design of plate girders adopting meaningful simplifications of the equations derived in the chapter on Plate Girders
More informationParametric analysis and torsion design charts for axially restrained RC beams
Structural Engineering and Mechanics, Vol. 55, No. 1 (2015) 1-27 DOI: http://dx.doi.org/10.12989/sem.2015.55.1.001 1 Parametric analysis and torsion design charts for axially restrained RC beams Luís F.A.
More informationAppendix K Design Examples
Appendix K Design Examples Example 1 * Two-Span I-Girder Bridge Continuous for Live Loads AASHTO Type IV I girder Zero Skew (a) Bridge Deck The bridge deck reinforcement using A615 rebars is shown below.
More informationEntrance exam Master Course
- 1 - Guidelines for completion of test: On each page, fill in your name and your application code Each question has four answers while only one answer is correct. o Marked correct answer means 4 points
More informationtwenty one concrete construction: materials & beams ELEMENTS OF ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SPRING 2014
ELEMENTS OF ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SPRING 2014 lecture twenty one concrete construction: http:// nisee.berkeley.edu/godden materials & beams Concrete Beams
More informationFinite Element Modelling with Plastic Hinges
01/02/2016 Marco Donà Finite Element Modelling with Plastic Hinges 1 Plastic hinge approach A plastic hinge represents a concentrated post-yield behaviour in one or more degrees of freedom. Hinges only
More informationCIVIL DEPARTMENT MECHANICS OF STRUCTURES- ASSIGNMENT NO 1. Brach: CE YEAR:
MECHANICS OF STRUCTURES- ASSIGNMENT NO 1 SEMESTER: V 1) Find the least moment of Inertia about the centroidal axes X-X and Y-Y of an unequal angle section 125 mm 75 mm 10 mm as shown in figure 2) Determine
More informationChapter 7. Highlights:
Chapter 7 Highlights: 1. Understand the basic concepts of engineering stress and strain, yield strength, tensile strength, Young's(elastic) modulus, ductility, toughness, resilience, true stress and true
More informationMODELLING NON-LINEAR BEHAVIOUR OF STEEL FIBRE REINFORCED CONCRETE
6th RILEM Symposium on Fibre-Reinforced Concretes (FRC) - BEFIB - September, Varenna, Italy MODELLING NON-LINEAR BEHAVIOUR OF STEEL FIBRE REINFORCED CONCRETE W. A. Elsaigh, J. M. Robberts and E.P. Kearsley
More informationDesign of Beams (Unit - 8)
Design of Beams (Unit - 8) Contents Introduction Beam types Lateral stability of beams Factors affecting lateral stability Behaviour of simple and built - up beams in bending (Without vertical stiffeners)
More informationSTRENGTH OF MATERIALS-I. Unit-1. Simple stresses and strains
STRENGTH OF MATERIALS-I Unit-1 Simple stresses and strains 1. What is the Principle of surveying 2. Define Magnetic, True & Arbitrary Meridians. 3. Mention different types of chains 4. Differentiate between
More informationREINFORCED CONCRETE STRUCTURES DESIGN AND DRAWING (ACE009)
LECTURE NOTES ON REINFORCED CONCRETE STRUCTURES DESIGN AND DRAWING (ACE009) III B. Tech I semester (Regulation- R16) Mr. Gude Ramakrishna Associate Professor DEPARTMENT OF CIVIL ENGINEERING INSTITUTE OF
More informationNORMAL STRESS. The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts.
NORMAL STRESS The simplest form of stress is normal stress/direct stress, which is the stress perpendicular to the surface on which it acts. σ = force/area = P/A where σ = the normal stress P = the centric
More information