INTERNATIONAL JOURNAL OF ADVANCED RESEARCH IN ENGINEERING AND TECHNOLOGY (IJARET) FUZZY FINITE ELEMENT ANALYSIS OF A CONDUCTION HEAT TRANSFER PROBLEM
|
|
- Julius Gilmore
- 5 years ago
- Views:
Transcription
1 INTERNATIONAL JOURNAL OF ADVANCED RESEARCH IN ENGINEERING AND TECHNOLOGY (IJARET) International Journal of Advanced Research in Engineering and Technology (IJARET), ISSN 0976 ISSN (Print) ISSN (Online) Volume 5, Issue 2, February (2014), pp IAEME: Journal Impact Factor (2014): (Calculated by GISI) IJARET I A E M E FUZZY FINITE ELEMENT ANALYSIS OF A CONDUCTION HEAT TRANSFER PROBLEM Ajeet Kumar Rai *, Gargi Jaiswal** *Department of Mechanical Engineering, SHIATS-DU Allahabad, India **Department of Applied Mechanics, IIT Delhi, India ABSTRACT In the heat transfer analysis, the material properties are taken as crisp. Since the input data are imprecise, no matter what techniques are used, the solution will not be reliable. In fuzzy finite element heat transfer analysis, the material properties are considered fuzzy parameters in order to take uncertainty into account. In the present study, a circular rod made up of iron has been considered. The end of the bar is insulated and heat transfer is taking place through the periphery. Here variation in material properties are considered as fuzzy and this requires the consideration of complex interval or fuzzy arithmetic in the analysis and the problem is discretized into finite number of elements and interval / fuzzy arithmetic is applied to solve this problem. The of temperature at different points (x = 0, x = 1.25, x = 2.5, x = 3.75, x = 5) of a fin is calculated by using different methods. Corresponding results are given and compared with the known results in the special cases. Keywords: Finite Element Method, Triangular Fuzzy Number & Cut. INTRODUCTION The fuzzy finite element method combines the well-established finite element method with the concept of fuzzy numbers, the latter being a special case of a fuzzy set. The advantage of using fuzzy numbers instead of real numbers lies in the incorporation of uncertainty (on material properties, parameters, geometry, initial conditions, etc.) in the finite element analysis. In the fuzzy finite element method uncertain geometrical, material and loading parameters are treated as fuzzy. The modeling of uncertain parameters as fuzzy is necessary when it is not possible to uniquely and reliably specify these parameters either deterministically or 6
2 stochastically. Often in such cases, only a limited number of samples are available or the reproduction conditions for generating sample elements vary. The parameters possess informal or lexical uncertainty, which may be modeled as fuzziness. Physical parameters possessing fuzziness with regard to external loading or material, geometrical and model parameters may occur at all points of a structure. An exhaustive work has been reported by various scholars showing the use of fuzzy logic combining with the results of FEM. Nicolai, De Baerdemaeker [1] has used finite element perturbation method for heat conduction problem with uncertain physical parameters. They found the temperature in heat conduction problem for randomly varying parameters with respect to time. B.M, Nicolai [2] has used a method for the direct computation of mean and variances of the temperature in conduction-heated objects with random variable thermo physical properties. Method is based on a Taylor expansion of the finite element formulation of the heat conduction equation and offers a powerful alternative to the computationally expensive Monte Carlo method. Both steadystate and transient problems are considered. The simulations indicate that the variability of the thermo physical properties may cause a considerable variability of the temperature within the heated object. Rao S.S, Sawyer J.P. [3] has applied the concepts of fuzzy logic to a static finite element analysis. The basic concepts of the theory of fuzzy logic are described. Later, the static finite element analysis will be extended to dynamic analyses. Naidoo P. [4] has studied the application of intelligent technology on a multi-variable dynamical system, where a fuzzy logic control algorithm was implemented to test the performance in temperature control. Jose et al. [5] has used four different global optimization algorithms for interval finite element analysis of (non)linear heat conduction problems: (i) sequential quadratic programming (SQP), (ii) a scatter search method (SSm), (iii) the vertex algorithm, and (iv) the response surface method (RSM). Their performance was compared based on a thermal sterilization problem and a food freezing problem. The RSM fuzzy finite element method was identified as the fastest algorithm among all the tested methods. It was shown that uncertain parameters may cause large uncertainties in the process variables. Majumadar Sarangam and Chakraverty S. [6] have proposed new methods to handle fuzzy system of linear equations. The material properties are actually uncertain and considered to vary in an interval or as fuzzy. And in that case; complex interval arithmetic or fuzzy arithmetic was considered in the analysis. Identification of the Problem Fig 1. Schematic diagram of a circular rod used as a fin In the present communication calculation of temperature at different points (x = 0, x = 1.25, x = 2.5, x = 3.75, x = 5) of a fin is done by using analytical method, Finite difference method, and Finite element method. The end of the fin is insulated and heat is convected through periphery. 7
3 Diameter was taken as 2 cm, length as 5 cm, heat transfer coefficient as 5 W/cm 2 K, and thermal conductivity as 70 W/cm-K. One dimensional steady state condition was assumed to solve the problem. Corresponding results are given and compared with the known result in special cases. MATERIALS AND METHODS 1. Analytical method 2. Finite difference method (FDM) Q left + Q right + q m. A. x = 0 Where, q m is the energy generation at node m, and m = 1, 2,3 m Finite element method (FEM) Steps: (i). Discretization of the problem Divide in small sub domain/ element. Each and every element has unique number. (ii). Finite element approximation..+ Where T 1, T 2 = temperature at respective nodes of the element N 1, N 2 = Shape functions (iii). Elemental equation for heat transfer (iv). Assembly (global equation)\ = 8
4 (v). Imposition of boundary conditions (vi). Nodal solution MODIFIED MATRIX - Solving the matrix obtained by using MATLAB. Here the problem is solved by fem firstly by increasing nodes and secondly by increasing element. Six cases will arise with two different number of nodes (i.e. 2 and 3) and three different number of elements ( i.e. 1, 2 and 3). Each case is solved and comparison of all results is done with the exact solution. 4. Fuzzy finite element method In this method the value of thermal conductivity K is considered as TFN [ 69, 70, 71] and heat transfer coefficient h is considered as TFN[ 4, 5,6 ]. The corresponding of temperature in this interval are plotted with the help of fuzzy. Triangular Fuzzy Number (TFN) and alpha cut Let X denote a universal set. Then, the membership function by which a fuzzy set A is usually defined as the form, where [0,1] denotes the interval of real numbers from 0 to 1. Such a function is called a membership function and the set defined by it is called a fuzzy set. A fuzzy number is a convex, normalized fuzzy set which is piecewise continuous and has the functional value (x) =1, where at precisely one element. Different types of fuzzy numbers are there. These are triangular fuzzy number, trapezoidal fuzzy number and Gaussian fuzzy number etc. Here we have discussed the said problem using triangular fuzzy number only. The membership function for triangular fuzzy number is as below. Fig.2 Triangular Fuzzy Number (TFN) [a, b, c] cut is an important concept of fuzzy set. Given then the alpha cut for above triangular fuzzy number may be written as [a, b, c] may be written as ]. 9
5 RESULTS AND DISCUSSION S.NO. DISCRET- E POINTS TEMPER- ATURE ANALY- TICAL FDM FEM 2N1E 2N2E 2N3E 3N1E 3N2E 3N3E 1 At x= 0 T 1 (given ) At x= 1.25 T At x = 2.5 T At x =3.75 T At x = 5.00 T T at x = Temperature in celsius EXACT FDM 2N 1 E 2N 2 E 2N 3 E 3N 1 E 3N 2 E 3N 3 E T at x =1.25 Different methods Fig.3 Value of temperature at x=1.25, T 2 T at x= 2.5 Temperature in Celsius exact FDM 2N 1E 2N 2E 2N 3E 3N 1E 3N 2E 3N 3E Different methods T at x= 2.5 Fig.4 Value of temperature at x=2.5, T 3 10
6 T at x = Temperature in celsius exact FDM 2N 1E 2N 2E 2N 3E 3N 1E 3N 2E 3N 3E T at x =3.75 Different methods Fig.5 Value of temperature at x=3.75, T 4 T at x = 5 Temperature in celsius exact FDM 2N 1E 2N 2E 2N 3E 3N 1E 3N 2E 3N 3E Different methods T at x = 5 Fig.6. Value of temperature at x= 5, T 5 Representation of FEM Results by Fuzzy Plot For Temperature at point 2. T 2 Fig7. 2 noded 1 element Fig.8. 2 noded 2 element 11
7 Fig.9. 2 noded 3 element Fig noded 1 element Fig noded 3 element Fig noded 2 element For temperature at point 3 T 3 Fig noded 1 element Fig noded 2 element Fig noded 3 element Fig noded 2 element 12
8 For temperature at point 4 T 4 Fig noded 1 element Fig noded 2 element Fig noded 3 element Fig noded 1 element Fig noded 2 element Fig noded 2 element For temperature at point 5 T 5 2 noded 1element 2 noded 2 element 13
9 2 noded 3 element 3 noded 1 element 3 noded 2 element 3 noded 3 element Here heat transfer problem is solved by Finite Difference Method and Finite Element Method. FDM shows a large variation in comparison to the exact solution or analytical solution. FEM results are near to the exact solution. In FEM we have taken 6 cases, by increasing the element and by increasing the node. By increasing the node we get better result. But results of increasing the number of elements are very close to the exact solution. So, it is clear that while increasing the node we get approximate solutions to the exact solution. By increasing node, we get less complication to solve the problem. Considering the uncertain parameters as fuzzy we have presented the result of the said problem in fuzzy plot. When the value of the alpha becomes zero the fuzzy results changes to interval form & for the value of alpha as one, the result changes into crisp form. We get a series of narrow & peak distribution of temperatures which reflect better solution for the said problem & are very close to the solution obtained from the traditional finite element method with crisp parameters. CONCLUSION The present work an attempt has been made to find the solution of a one dimensional steady state heat conduction problem by using different techniques with and without consideration of uncertainty in the material properties. Results obtained through different techniques are compared and the effect of varying number of nodes and number of elements on the results obtained by FEM is also studied. Uncertain parameters are considered as fuzzy and results are presented in triangular fuzzy plot. 14
10 REFERENCES 1) De Baerdemaeker, J., Computation of heat conduction in materials with random variable thermophysical properties. Int. J. Numer. Methods Eng. 36,(1993), ) Bart M. Nicolai, Jose A. Egea, NicoScheerlinck, Julio R. Banga, Ashim K. Datta, (2011) Fuzzy Finite Element Analysis of Heat Conduction Problems with Uncertain Parameters, Journal of Food Engineering 103, ) Rao, S. S., Sawyer, P., (1995) "Fuzzy Finite Element Approach for Analysis of Imprecisely Defined Systems", AIAA Journal, v. 33, n. 12, pp ) Naidoo P. (2003) The Application of Intelligent Technology on a Multi-Variable Dynamical System, Meccanica, 38(6): ) Bart M. Nicolai, Jose A. Egea, NicoScheerlinck, Julio R. Banga, Ashim K. Datta, Fuzzy Finite Element Analysis of Heat Conduction Problems with Uncertain Parameters, Journal of Food Engineering 103 (2011) ) Majumadar Sarangam and Chakraverty S. may (2012) fuzzy finite element method for one dimensional steady state heat conduction problem. 7) Ajeet Kumar Rai and Mustafa S Mahdi, A Practical Approach to Design and Optimization of Single Phase Liquid to Liquid Shell and Tube Heat Exchanger, International Journal of Mechanical Engineering & Technology (IJMET), Volume 3, Issue 3, 2012, pp , ISSN Print: , ISSN Online: ) Ajeet Kumar Rai and Ashish Kumar, A Review on Phase Change Materials & Their Applications, International Journal of Advanced Research in Engineering & Technology (IJARET), Volume 3, Issue 2, 2012, pp , ISSN Print: , ISSN Online: ) N.G.Narve and N.K.Sane, Heat Transfer and Fluid Flow Characteristics of Vertical Symmetrical Triangular Fin Arrays, International Journal of Advanced Research in Engineering & Technology (IJARET), Volume 4, Issue 2, 2013, pp , ISSN Print: , ISSN Online: ) Ajeet Kumar Rai, Shahbaz Ahmad and Sarfaraj Ahamad Idrisi, Design, Fabrication and Heat Transfer Study of Green House Dryer, International Journal of Mechanical Engineering & Technology (IJMET), Volume 4, Issue 4, 2013, pp. 1-7, ISSN Print: , ISSN Online:
6340(Print), ISSN (Online) Volume 3, Issue 3, Sep- Dec (2012) IAEME AND TECHNOLOGY (IJMET)
INTERNATIONAL International Journal of Mechanical JOURNAL Engineering OF MECHANICAL and Technology (IJMET), ENGINEERING ISSN 0976 AND TECHNOLOGY (IJMET) ISSN 0976 6340 (Print) ISSN 0976 6359 (Online) Volume
More informationSharp Interval Estimates for Finite Element Solutions with Fuzzy Material Properties
Sharp Interval Estimates for Finite Element Solutions with Fuzzy Material Properties R. L. Mullen, F.ASCE Department of Civil Engineering, Case Western Reserve University, Cleveland, Ohio 44106-7201 rlm@po.cwru.edu
More informationNUMERICAL INVESTIGATION OF COUNTER FLOW ISOSCELES RIGHT TRIANGULAR MICROCHANNEL HEAT EXCHANGER
International Journal of Mechanical Engineering and Technology IJMET) Volume 8, Issue 1, January 217, pp. 81 87, Article ID: IJMET_8_1_9 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=1
More informationAbstract. some transformation. thermal. solve these. aquifer.
23232323233 Journal of Uncertain Systems Vol.8, No.2, pp. 23-35, 204 Online at: www.jus.org.uk Uncertain Spectrum of emperatures in a Non Homogeneous Fin under Imprecisely Defined Conduction-Convection
More informationJ. Harish* and R.P. Rokade + *Graduate scholar Valliammai Engineering College, Kattankulathur, India + Principal Scientist
International Journal of Scientific & Engineering Research Volume 8, Issue 6, June-2017 109 Stochastic finite element analysis of simple hip truss Abstract- In this paper, nodal displacements and member
More informationUsing Computational Fluid Dynamics And Analysis Of Microchannel Heat Sink
International Journal of Engineering Inventions e-issn: 2278-7461, p-issn: 2319-6491 Volume 4, Issue 12 [Aug. 2015] PP: 67-74 Using Computational Fluid Dynamics And Analysis Of Microchannel Heat Sink M.
More informationApplication of Fuzzy Logic and Uncertainties Measurement in Environmental Information Systems
Fakultät Forst-, Geo- und Hydrowissenschaften, Fachrichtung Wasserwesen, Institut für Abfallwirtschaft und Altlasten, Professur Systemanalyse Application of Fuzzy Logic and Uncertainties Measurement in
More information6340(Print), ISSN (Online) Volume 4, Issue 3, May - June (2013) IAEME AND TECHNOLOGY (IJMET)
INTERNATIONAL International Journal of Mechanical JOURNAL Engineering OF MECHANICAL and Technology (IJMET), ENGINEERING ISSN 0976 AND TECHNOLOGY (IJMET) ISSN 0976 6340 (Print) ISSN 0976 6359 (Online) Volume
More informationSolution of Fuzzy System of Linear Equations with Polynomial Parametric Form
Available at http://pvamu.edu/aam Appl. Appl. Math. ISSN: 1932-9466 Vol. 7, Issue 2 (December 2012), pp. 648-657 Applications and Applied Mathematics: An International Journal (AAM) Solution of Fuzzy System
More informationComparison between Interval and Fuzzy Load Flow Methods Considering Uncertainty
Comparison between Interval and Fuzzy Load Flow Methods Considering Uncertainty T.Srinivasarao, 2 P.Mallikarajunarao Department of Electrical Engineering, College of Engineering (A), Andhra University,
More informationStochastic structural dynamic analysis with random damping parameters
Stochastic structural dynamic analysis with random damping parameters K. Sepahvand 1, F. Saati Khosroshahi, C. A. Geweth and S. Marburg Chair of Vibroacoustics of Vehicles and Machines Department of Mechanical
More informationGeneralized Triangular Fuzzy Numbers In Intuitionistic Fuzzy Environment
International Journal of Engineering Research Development e-issn: 2278-067X, p-issn : 2278-800X, www.ijerd.com Volume 5, Issue 1 (November 2012), PP. 08-13 Generalized Triangular Fuzzy Numbers In Intuitionistic
More informationHEAT TRANSFER AND TEMPERATURE DISTRIBUTION OF DIFFERENT FIN GEOMETRY USING NUMERICAL METHOD
JP Journal of Heat and Mass Transfer Volume 6, Number 3, 01, Pages 3-34 Available online at http://pphmj.com/journals/jphmt.htm Published by Pushpa Publishing House, Allahabad, INDIA HEAT TRANSFER AND
More informationEFFECTIVENESS OF HEAT TRANSFER INTENSIFIERS IN A FLUID CHANNEL
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 9, September 2018, pp. 58 62, Article ID: IJMET_09_09_007 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=9
More informationNetwork Analysis of Fuzzy Bi-serial and Parallel Servers with a Multistage Flow Shop Model
2st International Congress on Modelling and Simulation, Gold Coast, Australia, 29 Nov to 4 Dec 205 wwwmssanzorgau/modsim205 Network Analysis of Fuzzy Bi-serial and Parallel Servers with a Multistage Flow
More informationCompletion Time of Fuzzy GERT-type Networks with Loops
Completion Time of Fuzzy GERT-type Networks with Loops Sina Ghaffari 1, Seyed Saeid Hashemin 2 1 Department of Industrial Engineering, Ardabil Branch, Islamic Azad university, Ardabil, Iran 2 Department
More informationRobust Pareto Design of GMDH-type Neural Networks for Systems with Probabilistic Uncertainties
. Hybrid GMDH-type algorithms and neural networks Robust Pareto Design of GMDH-type eural etworks for Systems with Probabilistic Uncertainties. ariman-zadeh, F. Kalantary, A. Jamali, F. Ebrahimi Department
More informationFuzzy Compensation for Nonlinear Friction in a Hard Drive
Fuzzy Compensation for Nonlinear Friction in a Hard Drive Wilaiporn Ngernbaht, Kongpol Areerak, Sarawut Sujitjorn* School of Electrical Engineering, Institute of Engineering Suranaree University of Technology
More informationRanking of pentagonal fuzzy numbers applying incentre of centroids
Volume 7 No. 3 07, 65-74 ISSN: 3-8080 (printed version); ISSN: 34-3395 (on-line version) url: http://www.ijpam.eu ijpam.eu Ranking of pentagonal fuzzy numbers applying incentre of centroids P.Selvam, A.Rajkumar
More informationNEURO-FUZZY SYSTEM BASED ON GENETIC ALGORITHM FOR ISOTHERMAL CVI PROCESS FOR CARBON/CARBON COMPOSITES
NEURO-FUZZY SYSTEM BASED ON GENETIC ALGORITHM FOR ISOTHERMAL CVI PROCESS FOR CARBON/CARBON COMPOSITES Zhengbin Gu, Hejun Li, Hui Xue, Aijun Li, Kezhi Li College of Materials Science and Engineering, Northwestern
More informationDynamic System Identification using HDMR-Bayesian Technique
Dynamic System Identification using HDMR-Bayesian Technique *Shereena O A 1) and Dr. B N Rao 2) 1), 2) Department of Civil Engineering, IIT Madras, Chennai 600036, Tamil Nadu, India 1) ce14d020@smail.iitm.ac.in
More informationSafety Envelope for Load Tolerance and Its Application to Fatigue Reliability Design
Safety Envelope for Load Tolerance and Its Application to Fatigue Reliability Design Haoyu Wang * and Nam H. Kim University of Florida, Gainesville, FL 32611 Yoon-Jun Kim Caterpillar Inc., Peoria, IL 61656
More informationStochastic optimization - how to improve computational efficiency?
Stochastic optimization - how to improve computational efficiency? Christian Bucher Center of Mechanics and Structural Dynamics Vienna University of Technology & DYNARDO GmbH, Vienna Presentation at Czech
More informationINTERNATIONAL JOURNAL OF ADVANCED RESEARCH IN ENGINEERING AND TECHNOLOGY (IJARET)
INTERNATIONAL JOURNAL OF ADVANCED RESEARCH IN ENGINEERING AND TECHNOLOGY (IJARET) International Journal of Advanced Research in Engineering and Technology (IJARET), ISSN 0976 ISSN 0976-6480 (Print) ISSN
More informationThe Generalized Likelihood Uncertainty Estimation methodology
CHAPTER 4 The Generalized Likelihood Uncertainty Estimation methodology Calibration and uncertainty estimation based upon a statistical framework is aimed at finding an optimal set of models, parameters
More informationANALYSIS OF TRANSIENT HEAT CONDUCTION IN DIFFERENT GEOMETRIES BY POLYNOMIAL APPROXIMATION METHOD
Int. J. Mech. Eng. & Rob. Res. Devanshu Prasad, Research Paper ISSN 78 9 www.ijmerr.com Vol., No., April IJMERR. All Rights Reserved ANALYSIS OF TRANSIENT HEAT CONDUCTION IN DIFFERENT GEOMETRIES Y POLYNOMIAL
More informationCOMPUTING UNCERTAINTIES IN A DELTA WING COMPOSITE STRUCTURE USING INTERVAL-BASED METHODS
COMPUTING UNCERTAINTIES IN A DELTA WING COMPOSITE STRUCTURE USING INTERVAL-BASED METHODS Franck Delcroix 1, Chris Boyer 2, Vincent Braibant 2 1 Laboratoire de Modélisation et Mécanique des Structures,
More informationINTERNATIONAL JOURNAL OF MECHANICAL ENGINEERING AND TECHNOLOGY (IJMET)
INTERNATIONAL JOURNAL OF MECHANICAL ENGINEERING AND TECHNOLOGY (IJMET) International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 6340(Print), ISSN 0976 6340 (Print) ISSN 0976 6359
More informationA fuzzy finite element analysis technique for structural static analysis based on interval fields
A fuzzy finite element analysis technique for structural static analysis based on interval fields Wim Verhaeghe, Maarten De Munck, Wim Desmet, Dirk Vandepitte and David Moens Department of Mechanical Engineering,
More informationInstitute for Statics und Dynamics of Structures Fuzzy probabilistic safety assessment
Institute for Statics und Dynamics of Structures Fuzzy probabilistic safety assessment Bernd Möller Fuzzy probabilistic safety assessment randomness fuzzy randomness fuzzyness failure Fuzzy- Probabilistik
More informationTHERMO-MECHANICAL ANALYSIS IN PERFORATED ANNULAR FIN USING ANSYS
THERMO-MECHANICAL ANALYSIS IN PERFORATED ANNULAR FIN USING ANSYS Kunal Adhikary 1, Dr. Ashis Mallick 2 1,2 Department of Mechanical Engineering, IIT(ISM), Dhanbad-826004, Jharkhand, India Abstract Thermal
More informationMODELLING AND REAL TIME CONTROL OF TWO CONICAL TANK SYSTEMS OF NON-INTERACTING AND INTERACTING TYPE
MODELLING AND REAL TIME CONTROL OF TWO CONICAL TANK SYSTEMS OF NON-INTERACTING AND INTERACTING TYPE D. Hariharan, S.Vijayachitra P.G. Scholar, M.E Control and Instrumentation Engineering, Kongu Engineering
More informationInterval Finite Element Methods for Uncertainty Treatment in Structural Engineering Mechanics Rafi L. Muhanna Georgia Institute of Technology USA
Interval Finite Element Methods for Uncertainty Treatment in Structural Engineering Mechanics Rafi L. Muhanna Georgia Institute of Technology USA Second Scandinavian Workshop on INTERVAL METHODS AND THEIR
More informationInterpolation of Fuzzy if-then rules in context of Zadeh's Z-numbers P.Rani 1, G.Velammal 2 1
American International Journal of Research in Science, Technology, Engineering & Mathematics Available online at http://www.iasir.net ISSN (Print): 2328-3491, ISSN (Online): 2328-3580, ISSN (CD-ROM): 2328-3629
More informationSolution of Fuzzy Maximal Flow Network Problem Based on Generalized Trapezoidal Fuzzy Numbers with Rank and Mode
International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 9, Issue 7 (January 2014), PP. 40-49 Solution of Fuzzy Maximal Flow Network Problem
More informationStatistical Study of Complex Eigenvalues in Stochastic Systems
Research Journal of Applied Sciences, Engineering and Technology 2(3): 233-238, 2010 ISSN: 2040-7467 Maxwell Scientific Organization, 2010 Submitted Date: March 08, 2010 Accepted Date: March 24, 2010 Published
More informationFirst Order Non Homogeneous Ordinary Differential Equation with Initial Value as Triangular Intuitionistic Fuzzy Number
27427427427427412 Journal of Uncertain Systems Vol.9, No.4, pp.274-285, 2015 Online at: www.jus.org.uk First Order Non Homogeneous Ordinary Differential Equation with Initial Value as Triangular Intuitionistic
More informationDIFFERENTIAL TRANSFORMATION METHOD TO DETERMINE TEMPERATURE DISTRIBUTION OF HEAT RADIATING FINS WITH TEMPERATURE DEPENDENT THERMAL CONDUCTIVITY
Published by Global Research Publications, New Delhi, India DIFFERENTIAL TRANSFORMATION METHOD TO DETERMINE TEMPERATURE DISTRIBUTION OF HEAT RADIATING FINS WITH TEMPERATURE DEPENDENT THERMAL CONDUCTIVITY
More informationChapter 14 Heat and Temperature Notes
Chapter 14 Heat and Temperature Notes Section 1: Temperature The degree of or of an object. Related to the of an object s atoms or molecules What makes something hot? o Particles that make up o They have
More informationFuzzy reliability analysis of washing unit in a paper plant using soft-computing based hybridized techniques
Fuzzy reliability analysis of washing unit in a paper plant using soft-computing based hybridized techniques *Department of Mathematics University of Petroleum & Energy Studies (UPES) Dehradun-248007,
More informationSTEADY STATE THERMAL ANALYSIS OF HEAT SINK WITH FINS OF DIFFERENT GEOMETRY
International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 5, May 2017, pp. 196 206 Article ID: IJMET_08_05_019 Available online at http:// http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=5
More informationRESPONSE SURFACE METHODS FOR STOCHASTIC STRUCTURAL OPTIMIZATION
Meccanica dei Materiali e delle Strutture Vol. VI (2016), no.1, pp. 99-106 ISSN: 2035-679X Dipartimento di Ingegneria Civile, Ambientale, Aerospaziale, Dei Materiali DICAM RESPONSE SURFACE METHODS FOR
More informationINTERNATIONAL JOURNAL OF MECHANICAL ENGINEERING AND TECHNOLOGY (IJMET)
INTERNATIONAL JOURNAL OF MECHANICAL ENGINEERING AND TECHNOLOGY (IJMET) International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 ISSN 0976 6340 (Print) ISSN 0976 6359 (Online) Volume
More informationExperimental Analysis of Wire Sandwiched Micro Heat Pipes
Experimental Analysis of Wire Sandwiched Micro Heat Pipes Rag, R. L. Department of Mechanical Engineering, John Cox Memorial CSI Institute of Technology, Thiruvananthapuram 695 011, India Abstract Micro
More informationMethod of Weighted Residual Approach for Thermal Performance Evaluation of a Circular Pin fin: Galerkin Finite element Approach
ISSN (Print): 2347-671 (An ISO 3297: 27 Certified Organization) Vol. 6, Issue 4, April 217 Method of Weighted Residual Approach for Thermal Performance Evaluation of a Circular Pin fin: Galerkin Finite
More informationSOLVING POWER AND OPTIMAL POWER FLOW PROBLEMS IN THE PRESENCE OF UNCERTAINTY BY AFFINE ARITHMETIC
SOLVING POWER AND OPTIMAL POWER FLOW PROBLEMS IN THE PRESENCE OF UNCERTAINTY BY AFFINE ARITHMETIC Alfredo Vaccaro RTSI 2015 - September 16-18, 2015, Torino, Italy RESEARCH MOTIVATIONS Power Flow (PF) and
More informationDesign and Implementation of PI and PIFL Controllers for Continuous Stirred Tank Reactor System
International Journal of omputer Science and Electronics Engineering (IJSEE olume, Issue (4 ISSN 3 48 (Online Design and Implementation of PI and PIFL ontrollers for ontinuous Stirred Tank Reactor System
More informationEXPERIMENTAL AND NUMERICAL STUDIES OF A SPIRAL PLATE HEAT EXCHANGER
THERMAL SCIENCE: Year 2014, Vol. 18, No. 4, pp. 1355-1360 1355 EXPERIMENTAL AND NUMERICAL STUDIES OF A SPIRAL PLATE HEAT EXCHANGER by Rangasamy RAJAVEL Department of Mechanical Engineering, AMET University,
More informationUncertainty Quantification in MEMS
Uncertainty Quantification in MEMS N. Agarwal and N. R. Aluru Department of Mechanical Science and Engineering for Advanced Science and Technology Introduction Capacitive RF MEMS switch Comb drive Various
More informationA New Approach to Find All Solutions of Fuzzy Nonlinear Equations
The Journal of Mathematics and Computer Science Available online at http://www.tjmcs.com The Journal of Mathematics and Computer Science Vol. 4 No.1 (2012) 25-31 A New Approach to Find All Solutions of
More informationType-2 Fuzzy Shortest Path
Intern. J. Fuzzy Mathematical rchive Vol. 2, 2013, 36-42 ISSN: 2320 3242 (P), 2320 3250 (online) Published on 15 ugust 2013 www.researchmathsci.org International Journal of Type-2 Fuzzy Shortest Path V.
More information1038. Adaptive input estimation method and fuzzy robust controller combined for active cantilever beam structural system vibration control
1038. Adaptive input estimation method and fuzzy robust controller combined for active cantilever beam structural system vibration control Ming-Hui Lee Ming-Hui Lee Department of Civil Engineering, Chinese
More informationHistogram Arithmetic under Uncertainty of. Probability Density Function
Applied Mathematical Sciences, Vol. 9, 015, no. 141, 7043-705 HIKARI Ltd, www.m-hikari.com http://dx.doi.org/10.1988/ams.015.510644 Histogram Arithmetic under Uncertainty of Probability Density Function
More information6545(Print), ISSN (Online) Volume 4, Issue 3, May - June (2013), IAEME & TECHNOLOGY (IJEET)
INTERNATIONAL International Journal of JOURNAL Electrical Engineering OF ELECTRICAL and Technology (IJEET), ENGINEERING ISSN 976 & TECHNOLOGY (IJEET) ISSN 976 6545(Print) ISSN 976 6553(Online) Volume 4,
More informationINTERNATIONAL JOURNAL OF ADVANCED RESEARCH IN ENGINEERING AND TECHNOLOGY (IJARET) HYPERSONIC SIMILITUDE FOR PLANAR WEDGES. Asha Crasta 1, S. A.
INTERNATIONAL JOURNAL OF ADVANCED RESEARCH IN ENGINEERING AND TECHNOLOGY (IJARET) International Journal of Advanced Research in Engineering and Technology (IJARET), ISSN 0976 ISSN 0976-6480 (Print) ISSN
More informationSome Researches of Thermal Problem in 3D ICs. Dr. Xiuyun DU Prof. Zhenan TANG Dalian University of Technology
Some Researches of Thermal Problem in 3D ICs Dr. Xiuyun DU Prof. Zhenan TANG Dalian University of Technology Outline 1. Thermal analysis problems in 3D ICs 2. Deterministic analysis of the thermal problems
More informationVariable Sampling Effect for BLDC Motors using Fuzzy PI Controller
Indian Journal of Science and Technology, Vol 8(35), DOI:10.17485/ijst/2015/v8i35/68960, December 2015 ISSN (Print) : 0974-6846 ISSN (Online) : 0974-5645 Variable Sampling Effect BLDC Motors using Fuzzy
More informationSpectral methods for fuzzy structural dynamics: modal vs direct approach
Spectral methods for fuzzy structural dynamics: modal vs direct approach S Adhikari Zienkiewicz Centre for Computational Engineering, College of Engineering, Swansea University, Wales, UK IUTAM Symposium
More informationResearch Article A New Approach for Optimization of Real Life Transportation Problem in Neutrosophic Environment
Mathematical Problems in Engineering Volume 206 Article ID 5950747 9 pages http://dx.doi.org/0.55/206/5950747 Research Article A New Approach for Optimization of Real Life Transportation Problem in Neutrosophic
More informationKeywords: Spiral plate heat exchanger, Heat transfer, Nusselt number
EXPERIMENTAL AND NUMERICAL STUDIES OF A SPIRAL PLATE HEAT EXCHANGER Dr.RAJAVEL RANGASAMY Professor and Head, Department of Mechanical Engineering Velammal Engineering College,Chennai -66,India Email:rajavelmech@gmail.com
More informationCode No: RT41033 R13 Set No. 1 IV B.Tech I Semester Regular Examinations, November - 2016 FINITE ELEMENT METHODS (Common to Mechanical Engineering, Aeronautical Engineering and Automobile Engineering)
More informationAnalysis of Steady State Heat Conduction Problem Using EFGM
International Journal of Engineering and Management Research, Vol.-2, Issue-6, December 2012 ISSN No.: 2250-0758 Pages: 40-47 www.ijemr.net Analysis of Steady State Heat Conduction Problem Using EFGM Manpreet
More informationLab 5: Post Processing and Solving Conduction Problems. Objective:
Lab 5: Post Processing and Solving Conduction Problems Objective: The objective of this lab is to use the tools we have developed in MATLAB and SolidWorks to solve conduction heat transfer problems that
More informationA New Approach for Optimization of Real Life Transportation Problem in Neutrosophic Environment
1 A New Approach for Optimization of Real Life Transportation Problem in Neutrosophic Environment A.Thamaraiselvi 1, R.Santhi 2 Department of Mathematics, NGM College, Pollachi, Tamil Nadu-642001, India
More informationComparison of heat transfer characteristics of liquid coolants in forced convection cooling in a micro heat sink
Nivesh Agrawal et al. / IJAIR ISSN: 78-7844 Comparison of heat transfer characteristics of liquid coolants in forced convection cooling in a micro heat sink Mr.Nivesh Agrawal #1 Mr.Mahesh Dewangan * #1
More informationJEPPIAAR ENGINEERING COLLEGE
JEPPIAAR ENGINEERING COLLEGE Jeppiaar Nagar, Rajiv Gandhi Salai 600 119 DEPARTMENT OFMECHANICAL ENGINEERING QUESTION BANK VI SEMESTER ME6603 FINITE ELEMENT ANALYSIS Regulation 013 SUBJECT YEAR /SEM: III
More informationInternational Journal of Pure and Applied Sciences and Technology
Int. J. Pure Appl. Sci. Technol., 14(1) (2013), pp. 16-26 International Journal of Pure and Applied Sciences and Technology ISSN 2229-6107 Available online at www.ijopaasat.in Research Paper First Order
More informationA Numerical Study on Static and Dynamic Characteristics of Electromagnetic Air Compressor used in Household Refrigerators
Journal of Experimental & Applied Mechanics ISSN: 2230-9845 (online), ISSN: 2321-516X (print) Volume 5, Issue 3 www.stmjournals.com A Numerical Study on Static and Dynamic Characteristics of Electromagnetic
More informationDETERMINATION OF HEAT TRANSFER COEFFICIENT OF BRAKE ROTOR DISC USING CFD SIMULATION
International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 3, May June 2016, pp.276 284, Article ID: IJMET_07_03_025 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=7&itype=3
More informationChapter 5. Formulation of FEM for Unsteady Problems
Chapter 5 Formulation of FEM for Unsteady Problems Two alternatives for formulating time dependent problems are called coupled space-time formulation and semi-discrete formulation. The first one treats
More informationComputational Fluid Dynamics of Parallel Flow Heat Exchanger
International Journal of Sciences: Basic and Applied Research (IJSBAR) ISSN 2307-4531 (Print & Online) http://gssrr.org/index.php?journal=journalofbasicandapplied ---------------------------------------------------------------------------------------------------------------------------
More informationCritical Paths Identification on Fuzzy Network Project
IOSR Journal of Mathematics (IOSR-JM) e-issn: 2278-5728, p-issn: 2319-765X. Volume 11, Issue 1 Ver. VI (Jan - Feb. 2015), PP 49-54 www.iosrjournals.org Critical Paths Identification on Fuzzy Network Project
More informationMODELLING ANALYSIS & DESIGN OF DSP BASED NOVEL SPEED SENSORLESS VECTOR CONTROLLER FOR INDUCTION MOTOR DRIVE
INTERNATIONAL JOURNAL OF ADVANCED RESEARCH IN ENGINEERING International Journal of Advanced Research in Engineering and Technology (IJARET), ISSN 0976 6480(Print), ISSN 0976 6499(Online), AND TECHNOLOGY
More informationThis chapter focuses on the study of the numerical approximation of threedimensional
6 CHAPTER 6: NUMERICAL OPTIMISATION OF CONJUGATE HEAT TRANSFER IN COOLING CHANNELS WITH DIFFERENT CROSS-SECTIONAL SHAPES 3, 4 6.1. INTRODUCTION This chapter focuses on the study of the numerical approximation
More informationFUZZY FINITE ELEMENT METHOD AND ITS APPLICATION
TRENDS IN COMPUTATIONAL STRUCTURAL MECHANICS W.A. Wall, K.U. Bletzinger and K. Schweizerhof (Eds.) CIMNE, Barcelona, Spain 2001 FUZZY FINITE ELEMENT METHOD AND ITS APPLICATION B. Möller*, M. Beer, W. Graf
More informationFuzzy probabilistic structural analysis considering fuzzy random functions
Fuzzy probabilistic structural analysis considering fuzzy random functions.-u. Sickert, M. Beer, W. Graf & B. Möller Institute of Structural Analysis, Dresden University of Technology, Germany Keywords:
More informationRobust Mechanism synthesis with random and interval variables
Scholars' Mine Masters Theses Student Research & Creative Works Fall 2007 Robust Mechanism synthesis with random and interval variables Pavan Kumar Venigella Follow this and additional works at: http://scholarsmine.mst.edu/masters_theses
More informationINTERNATIONAL JOURNAL OF ELECTRICAL ENGINEERING & TECHNOLOGY (IJEET)
INTERNATIONAL JOURNAL OF ELECTRICAL ENGINEERING & TECHNOLOGY (IJEET) Proceedings of the 2 nd International Conference on Current Trends in Engineering and Management ICCTEM -2014 ISSN 0976 6545(Print)
More informationCOMPUTATIONAL ANALYSIS OF ENCAPSULATED THERMAL ENERGY PHASE CHANGE STORAGE SYSTEM: CYLINDRICAL AND SPHERICAL GEOMETRY
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 5, May 2018, pp. 662 668, Article ID: IJMET_09_05_073 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=5
More informationAnalysis of Fluid Film Stiffness and Damping coefficient for A Circular Journal Bearing with Micropolar Fluid
et International Journal on Emerging Technologies 5(1): 206-211(2014) ISSN No. (Print) : 0975-8364 ISSN No. (Online) : 2249-3255 Analysis of Fluid Film Stiffness Damping coefficient for A Circular Journal
More informationFuel BurnupCalculations and Uncertainties
Fuel BurnupCalculations and Uncertainties Outline Review lattice physics methods Different approaches to burnup predictions Linkage to fuel safety criteria Sources of uncertainty Survey of available codes
More informationStructural Reliability Analysis using Uncertainty Theory
Structural Reliability Analysis using Uncertainty Theory Zhuo Wang Uncertainty Theory Laboratory, Department of Mathematical Sciences Tsinghua University, Beijing 00084, China zwang058@sohu.com Abstract:
More informationPraveen Kumar Assistant Professor, School of Mechanical Engineering, VIT University, Vellore, India
International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 11, November 2017, pp. 457 466, Article ID: IJMET_08_11_049 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=11
More information6480(Print), ISSN (Online) Volume 4, Issue 7, November December (2013), IAEME ENGINEERING AND TECHNOLOGY (IJARET)
International INTERNATIONAL Journal of Advanced Research JOURNAL in Engineering OF ADVANCED and Technology RESEARCH (IJARET), ISSN IN 0976 ENGINEERING AND TECHNOLOGY (IJARET) ISSN 0976-6480 (Print) ISSN
More informationFINITE ELEMENT ANALYSIS USING THE TANGENT STIFFNESS MATRIX FOR TRANSIENT NON-LINEAR HEAT TRANSFER IN A BODY
Heat transfer coeff Temperature in Kelvin International Journal of Engineering Research and Applications (IJERA) ISSN: 2248-9622 FINITE ELEMENT ANALYSIS USING THE TANGENT STIFFNESS MATRIX FOR TRANSIENT
More informationNumerical Investigation of Convective Heat Transfer in Pin Fin Type Heat Sink used for Led Application by using CFD
GRD Journals- Global Research and Development Journal for Engineering Volume 1 Issue 8 July 2016 ISSN: 2455-5703 Numerical Investigation of Convective Heat Transfer in Pin Fin Type Heat Sink used for Led
More informationADAPTIVE TEMPERATURE CONTROL IN CONTINUOUS STIRRED TANK REACTOR
INTERNATIONAL JOURNAL OF ELECTRICAL ENGINEERING & TECHNOLOGY (IJEET) International Journal of Electrical Engineering and Technology (IJEET), ISSN 0976 6545(Print), ISSN 0976 6545(Print) ISSN 0976 6553(Online)
More informationINVESTIGATION ON THE STRESS CONCENTRATION IN METALLIC FLAT PLATES DUE TO HOLES WITH DIFFERENT CONFIGURATIONS
International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 7, July 2017, pp. 1718 1725, Article ID: IJMET_08_07_189 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=7
More informationChapters 16 Temperature and Heat
Chapters 16 Temperature and Heat 1 Overview of Chapter 16 Temperature and the Zeroth Law of Thermodynamics Temperature Scales Thermal Expansion Heat and Mechanical Work Specific Heat Conduction, Convection,
More informationLecture 9 Thermal Analysis
Lecture 9 Thermal Analysis 16.0 Release Introduction to ANSYS Mechanical 1 2015 ANSYS, Inc. February 27, 2015 Chapter Overview In this chapter, performing steady-state thermal analyses in Mechanical will
More informationBasics of Uncertainty Analysis
Basics of Uncertainty Analysis Chapter Six Basics of Uncertainty Analysis 6.1 Introduction As shown in Fig. 6.1, analysis models are used to predict the performances or behaviors of a product under design.
More informationNumerical Probabilistic Analysis under Aleatory and Epistemic Uncertainty
Numerical Probabilistic Analysis under Aleatory and Epistemic Uncertainty Boris S. Dobronets Institute of Space and Information Technologies, Siberian Federal University, Krasnoyarsk, Russia BDobronets@sfu-kras.ru
More informationThermo-mechanical Investigation of Ventilated Disc Brake with Finite Element Analysis
Thermo-mechanical Investigation of Ventilated Disc Brake with Finite Element Analysis Arifin #1, Mohammad Tauviqirrahman #2, Muchammad *3, J. Jamari #, A.P. Bayuseno # # Laboratory for Engineering Design
More informationDepartment of Energy Science & Engineering, IIT Bombay, Mumbai, India. *Corresponding author: Tel: ,
ICAER 2011 AN EXPERIMENTAL AND COMPUTATIONAL INVESTIGATION OF HEAT LOSSES FROM THE CAVITY RECEIVER USED IN LINEAR FRESNEL REFLECTOR SOLAR THERMAL SYSTEM Sudhansu S. Sahoo* a, Shinu M. Varghese b, Ashwin
More informationFailure Mode Screening Using Fuzzy Set Theory
International Mathematical Forum, 4, 9, no. 6, 779-794 Failure Mode Screening Using Fuzzy Set Theory D. Pandey a, Sanjay Kumar Tyagi b and Vinesh Kumar c a, c Department of Mathematics, C.C.S. University,
More informationFINITE ELEMENTS ANALYSIS OF THERMAL STEADY STATE, USING ANSYS
FINITE ELEMENTS ANALYSIS OF THERMAL STEADY STATE, USING ANSYS Gavril GREBENIŞAN 1, Ioan Eugen RADU 2 Ioan ANTON 3 1 University of Oradea, grebe@uoradea.ro 2 University of Oradea, iradu@uoradea.ro 3 GMAB
More informationDIRECT TORQUE CONTROL OF THREE PHASE INDUCTION MOTOR USING FUZZY LOGIC
DIRECT TORQUE CONTROL OF THREE PHASE INDUCTION MOTOR USING FUZZY LOGIC 1 RAJENDRA S. SONI, 2 S. S. DHAMAL 1 Student, M. E. Electrical (Control Systems), K. K. Wagh College of Engg. & Research, Nashik 2
More informationINTERNATIONAL JOURNAL OF CIVIL ENGINEERING AND TECHNOLOGY (IJCIET)
INTERNATIONAL JOURNAL OF CIVIL ENGINEERING AND TECHNOLOGY (IJCIET) International Journal of Civil Engineering and Technology (IJCIET), ISSN 0976 6308 ISSN 0976 6308 (Print) ISSN 0976 6316(Online) Volume
More informationPREDICTION OF TEMPERATURE VARIATIONS FOR INDUSTRIAL BUS DUCT SYSTEM UNDER FORCED CONVECTION COOLING WITH VARIOUS ASPECT RATIOS USING MATLAB
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 2, February 2018, pp. 734 741 Article ID: IJMET_09_02_076 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=2
More informationFinite Element Structural Analysis using Imprecise Probabilities Based on P-Box Representation
Finite Element Structural Analysis using Imprecise Probabilities Based on P-Box Representation Hao Zhang 1, R. L. Mullen 2, and R. L. Muhanna 3 1 University of Sydney, Sydney 2006, Australia, haozhang@usyd.edu.au
More information