Cree XLamp XM-L EasyWhite LEDs

Transcription

1 Cree XLamp XM-L EasyWhite LEDs Product family data sheet CLD-DS38 Rev 8G Product Description FEATURES Table of Contents The XLamp XM-L EasyWhite (EZW) LED eliminates chromaticity binning, and enables luminaire and bulb manufacturers to deliver the consistent color and high efficacy light output of a multi die LED in the compact XM-L footprint. XLamp XM L EasyWhite LEDs can reduce LED to LED color variation to within a 2 step MacAdam ellipse, 94% smaller than the total area of the corresponding ANSI C color region. The XLamp XM-L EasyWhite LED is the perfect choice for lighting applications where moderate to high luminous flux output is required from a single, small point source. Example applications include: LED retrofit bulbs, commercial/ retail display spotlights, and other indoor general-illumination applications. Available in 4-step and 2-step EasyWhite bins at 2700 K, 3000 K, 3500 K, 4000 K, 5000 K CCT Wide range of operating current up to 2 6 V 85 C binning and characterization Available in 6 V and 12 V versions Low thermal resistance: 2.5 C/W Wide viewing angle: 115 Wide variety of CRI choices: standard CRI as well as 80-, 85-, 90 minimum CRI Electrically neutral thermal path Unlimited floor life at 30 ºC/85% RH Reflow solderable - JEDEC J STD 020C RoHS and REACh compliant UL recognized component (E349212) Copyright Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, XLamp and EasyWhite are registered trademarks and the Cree logo and XM-L are trademarks of Cree, Inc. UL and the UR logo are registered trademarks of UL LLC. Characteristics...2 Characteristics, Standard Order Codes and Bins, 6-Volt XM-L EZW...3 Characteristics, Standard Order Codes and Bins, 12-Volt XM-L EZW...6 Relative Spectral Power Distribution...9 Relative vs. Junction Temperature...9 Electrical Characteristics...10 Relative vs. Current...11 Relative vs. Current and Temperature...12 Typical Spatial Distribution...13 Thermal Design...13 Performance Groups Brightness...14 Performance Groups...14 Cree EasyWhite Bins Plotted on the 1931 CIE Color Space...15 Cree ANSI White Bins Plotted on the 1931 CIE Color Space...16 Bin and Formats...16 Reflow Soldering Characteristics...17 Notes...18 Mechanical Dimensions...20 Tape and Reel...21 Packaging...22 Cree, Inc Silicon Drive Durham, NC USA Tel:

2 Characteristics Characteristics Unit Minimum Typical Maximum Thermal resistance, junction to solder point C/W 2.5 Viewing angle (FWHM) degrees 115 Temperature coefficient of voltage (6 V) mv/ C -6.0 Temperature coefficient of voltage (12 V) mv/ C ESD withstand voltage (HBM per Mil-Std-883D) V 8000 DC forward current (6 V) ma 2000 DC forward current (12 V) ma 1000 Reverse current (6 V, 12 V) ma -0.1 Forward voltage (@ 700 ma, 85 C, 6 V) V Forward voltage (@ 350 ma, 85 C, 12 V) V LED junction temperature C 150 2

3 Characteristics, Standard s and Bins, 6-Volt XM-L EZW (700 ma, T j = 85 C) The following table provides the order codes for 6-Volt XLamp XM-L EZW LEDs. Color CCT Range Minimum 700 ma Group 85 C 25 C* 2-Step 4-Step U XMLEZW B00U450H XMLEZW B00U450F 5000 K U XMLEZW B00U550H XMLEZW B00U550F 50H 50F U XMLEZW B00U650H XMLEZW B00U650F V XMLEZW B00V250H XMLEZW B00V250F U XMLEZW B00U240H XMLEZW B00U240F 4000 K U H XMLEZW B00U340H 40F XMLEZW B00U340F U XMLEZW B00U440H XMLEZW B00U440F T XMLEZW B00T635H XMLEZW B00T635F Standard CRI EasyWhite 3500 K U H XMLEZW B00U235H 35F XMLEZW B00U235F U XMLEZW B00U335H XMLEZW B00U335F T XMLEZW B00T530H XMLEZW B00T530F 3000 K T XMLEZW B00T630H XMLEZW B00T630F 30H 30F U XMLEZW B00U230H XMLEZW B00U230F U XMLEZW B00U330H XMLEZW B00U330F T XMLEZW B00T427H XMLEZW B00T427F 2700 K T XMLEZW B00T527H XMLEZW B00T527F 27H 27F T XMLEZW B00T627H XMLEZW B00T627F U XMLEZW B00U227H XMLEZW B00U227F Notes Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements. See the Measurements section (page 18). For Standard CRI parts, typical CRI is 80 for K CCT parts and 82 for K CCT parts. * 25 C are calculated and for reference only. 3

4 Characteristics, Standard s and Bins, 6-Volt XM-L EZW (700 ma, T j = 85 C) - Continued Color CCT Range Minimum 700 ma Group 85 C 25 C* 2-Step 4-Step T XMLEZW B0HT640H XMLEZW B0HT640F 4000 K U XMLEZW B0HU240H XMLEZW B0HU240F 40H 40F U XMLEZW B0HU340H XMLEZW B0HU340F U XMLEZW B0HU440H XMLEZW B0HU440F T XMLEZW B0HT535H XMLEZW B0HT535F 3500 K T XMLEZW B0HT635H XMLEZW B0HT635F 35H 35F U XMLEZW B0HU235H XMLEZW B0HU235F 80-CRI Minimum EasyWhite U XMLEZW B0HU335H XMLEZW B0HU335F T XMLEZW B0HT530H XMLEZW B0HT530F 3000 K T XMLEZW B0HT630H XMLEZW B0HT630F 30H 30F U XMLEZW B0HU230H XMLEZW B0HU230F U XMLEZW B0HU330H XMLEZW B0HU330F T XMLEZW B0HT427H XMLEZW B0HT427F 2700 K T XMLEZW B0HT527H XMLEZW B0HT527F 27H 27F T XMLEZW B0HT627H XMLEZW B0HT627F U XMLEZW B0HU227H XMLEZW B0HU227F T XMLEZW B0PT330H XMLEZW B0PT330F 3000 K T XMLEZW B0PT430H XMLEZW B0PT430F 30H 30F T XMLEZW B0PT530H XMLEZW B0PT530F 85-CRI Minimum EasyWhite T XMLEZW B0PT630H XMLEZW B0PT630F T XMLEZW B0PT227H XMLEZW B0PT227F 2700 K T XMLEZW B0PT327H XMLEZW B0PT327F 27H 27F T XMLEZW B0PT427H XMLEZW B0PT427F T XMLEZW B0PT527H XMLEZW B0PT527F Notes Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements. See the Measurements section (page 18). For Standard CRI parts, typical CRI is 80 for K CCT parts and 82 for K CCT parts. * 25 C are calculated and for reference only. 4

5 Characteristics, Standard s and Bins, 6-Volt XM-L EZW (700 ma, T j = 85 C) - Continued Color CCT Range Minimum 700 ma Group 85 C 25 C* 2-Step 4-Step T XMLEZW B0UT230H XMLEZW B0UT230F 3000 K T XMLEZW B0UT330H XMLEZW B0UT330F 30H 30F T XMLEZW B0UT430H XMLEZW B0UT430F 90-CRI Minimum EasyWhite T XMLEZW B0UT530H XMLEZW B0UT530F S XMLEZW B0US627H XMLEZW B0US627F 2700 K T XMLEZW B0UT227H XMLEZW B0UT227F 27H 27F T XMLEZW B0UT327H XMLEZW B0UT327F T XMLEZW B0UT427H XMLEZW B0UT427F Color CCT Range Group Minimum 700 ma 85 C 25 C* s U XMLEZW B00U40E3 ANSI White 5000 K U XMLEZW B00U50E3 0E3 U XMLEZW B00U60E3 V XMLEZW B00V20E3 Notes Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements. See the Measurements section (page 18). For Standard CRI parts, typical CRI is 80 for K CCT parts and 82 for K CCT parts. * 25 C are calculated and for reference only. 5

6 Characteristics, Standard s and Bins, 12-Volt XM-L EZW (350 ma, T J = 85 C) The following table provides the order codes for 12-Volt XLamp XM-L EZW LEDs. Color CCT Range Minimum 350 ma Group 85 C 25 C* 2-Step 4-Step U XMLEZW D00U450H XMLEZW D00U450F 5000 K U XMLEZW D00U550H XMLEZW D00U550F 50H 50F U XMLEZW D00U650H XMLEZW D00U650F V XMLEZW D00V250H XMLEZW D00V250F U XMLEZW D00U240H XMLEZW D00U240F 4000 K U H XMLEZW D00U340H 40F XMLEZW D00U340F U XMLEZW D00U440H XMLEZW D00U440F T XMLEZW D00T635H XMLEZW D00T635F Standard CRI EasyWhite 3500 K U H XMLEZW D00U235H 35F XMLEZW D00U235F U XMLEZW D00U335H XMLEZW D00U335F T XMLEZW D00T530H XMLEZW D00T530F 3000 K T XMLEZW D00T630H XMLEZW D00T630F 30H 30F U XMLEZW D00U230H XMLEZW D00U230F U XMLEZW D00U330H XMLEZW D00U330F T XMLEZW D00T427H XMLEZW D00T427F 2700 K T XMLEZW D00T527H XMLEZW D00T527F 27H 27F T XMLEZW D00T627H XMLEZW D00T627F U XMLEZW D00U227H XMLEZW D00U227F Notes Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements. See the Measurements section (page 18). For Standard CRI parts, typical CRI is 80 for K CCT parts and 82 for K CCT parts. * 25 C are calculated and for reference only. 6

7 Characteristics, Standard s and Bins, 12-Volt XM-L EZW (350 ma, T J = 85 C) - Continued Color CCT Range Minimum 350 ma Group 85 C 25 C* 2-Step 4-Step T XMLEZW D0HT640H XMLEZW D0HT640F 4000 K U XMLEZW D0HU240H XMLEZW D0HU240F 40H 40F U XMLEZW D0HU340H XMLEZW D0HU340F U XMLEZW D0HU440H XMLEZW D0HU440F T XMLEZW D0HT535H XMLEZW D0HT535F 3500 K T XMLEZW D0HT635H XMLEZW D0HT635F 35H 35F U XMLEZW D0HU235H XMLEZW D0HU235F 80-CRI Minimum EasyWhite U XMLEZW D0HU335H XMLEZW D0HU335F T XMLEZW D0HT530H XMLEZW D0HT530F 3000 K T XMLEZW D0HT630H XMLEZW D0HT630F 30H 30F U XMLEZW D0HU230H XMLEZW D0HU230F U XMLEZW D0HU330H XMLEZW D0HU330F T XMLEZW D0HT427H XMLEZW D0HT427F 2700 K T XMLEZW D0HT527H XMLEZW D0HT527F 27H 27F T XMLEZW D0HT627H XMLEZW D0HT627F U XMLEZW D0HU227H XMLEZW D0HU227F T XMLEZW D0PT330H XMLEZW D0PT330F 3000 K T XMLEZW D0PT430H XMLEZW D0PT430F 30H 30F T XMLEZW D0PT530H XMLEZW D0PT530F 85-CRI Minimum EasyWhite T XMLEZW D0PT630H XMLEZW D0PT630F T XMLEZW D0PT227H XMLEZW D0PT227F 2700 K T XMLEZW D0PT327H XMLEZW D0PT327F 27H 27F T XMLEZW D0PT427H XMLEZW D0PT427F T XMLEZW D0PT527H XMLEZW D0PT527F Notes Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements. See the Measurements section (page 18). For Standard CRI parts, typical CRI is 80 for K CCT parts and 82 for K CCT parts. * 25 C are calculated and for reference only. 7

8 Characteristics, Standard s and Bins, 12-Volt XM-L EZW (350 ma, T J = 85 C) - Continued Color CCT Range Minimum 350 ma Group 85 C 25 C* 2-Step 4-Step T XMLEZW D0UT230H XMLEZW D0UT230F 3000 K T XMLEZW D0UT330H XMLEZW D0UT330F 30H 30F T XMLEZW D0UT430H XMLEZW D0UT430F 90-CRI Minimum EasyWhite T XMLEZW D0UT530H XMLEZW D0UT530F S XMLEZW D0US627H XMLEZW D0US627F 2700 K T XMLEZW D0UT227H XMLEZW D0UT227F 27H 27F T XMLEZW D0UT327H XMLEZW D0UT327F T XMLEZW D0UT427H XMLEZW D0UT427F Color CCT Range Group Minimum 350 ma 85 C 25 C* s U XMLEZW D00U40E3 ANSI White 5000 K U XMLEZW D00U50E3 0E3 U XMLEZW D00U60E3 V XMLEZW D00V20E3 Notes Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and ±2 on CRI measurements. See the Measurements section (page 18). For Standard CRI parts, typical CRI is 80 for K CCT parts and 82 for K CCT parts. * 25 C are calculated and for reference only. 8

9 Relative Spectral Power Distribution 100 Relative Radiant Power (%) K CCT 3000 K CCT Wavelength (nm) Relative vs. Junction Temperature (6-V - I F = 700 ma; 12-V - I F = 350 ma) 120% 100% Relative Luminous 80% 60% 40% 20% 0% Junction Temperature (ºC) 9

10 Electrical Characteristics (T J = 85 C) Forward Current (ma) V Forward Voltage (V) 1000 Forward Current (ma) V Forward Voltage (V) 10

11 Relative vs. Current (T J = 85 C) 225% 200% Relative Luminous 175% 150% 125% 100% 75% 50% 6 V 25% 0% Forward Current (ma) 225% 200% Relative Luminous 175% 150% 125% 100% 75% 50% 12 V 25% 0% Forward Current (ma) 11

12 Relative vs. Current and Temperature XLamp XM-L EZW LED, 6-V ΔCCx ΔCCy Current (ma) XLamp XM-L EZW LED, 12-V ΔCCx ΔCCy Current (ma) XLamp XM-L EZW LED, 6-V, 12V ΔCCx ΔCCy Tsp ( C) 12

13 Typical Spatial Distribution 100 Relative Luminous Intensity (%) Angle (º) Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. XLamp XM-L EZW LED, 6-v XLamp XM-L EZW LED, 12-V Maximum Current (ma) Rj-a = 4 C/W Rj-a = 7 C/W Rj-a = 10 C/W Maximum Current (ma) Rj-a = 4 C/W Rj-a = 7 C/W Rj-a = 10 C/W Rj-a = 15 C/W Rj-a = 15 C/W Ambient Temperature (ºC) Ambient Temperature (ºC) 13

14 Performance Groups Brightness (T J = 85 C) XLamp XM-L EasyWhite LEDs are tested for luminous flux and placed into one the following bins. Group Code Minimum 700 ma, 6 V (@ 350 ma, 12 V) Maximum 700 ma, 6 V (@ 350 ma, 12 V) S T T T T T U U U U U V Performance Groups (T J = 85 C) XLamp XM-L EasyWhite LEDs are tested for chromaticity and placed into one of the regions defined by the following bounding coordinates. EasyWhite Color Temperatures 4-Step Code CCT x y F 5000 K F 4000 K F 3500 K F 3000 K F 2700 K EasyWhite Color Temperatures 2-Step Code CCT x y H 5000 K H 4000 K H 3500 K H 3000 K H 2700 K

15 Performance Groups (T J = 85 C) - Continued ANSI White Bins Code CCT Bin Code x y A B E K C D Cree EasyWhite Bins Plotted on the 1931 CIE Color Space (T J = 85 C) ANSI C Quadrangle EasyWhite 4-step EasyWhite 2-step 3500 K 3000 K 2700 K K 4000 K 0.40 CCy K 5000 K CCx 15

16 Cree ANSI White Bins Plotted on the 1931 CIE Color Space (T j =85 C) 0.45 CCy K 4750 K 5300 K 3B0 3C K 4300 K 5A0 5B K 5D0 5C0 6A K 6B K 6C0 7A0 6D K 7B0 7D0 7C K 3000 K 8A0 8B0 8D0 8C0 ANSI C78.377A 2600 K 2700 K A0 3D CCx Bin and Formats Bin codes and order codes are configured as follows: order Code bin Code Series XML = XM-L Series XML = XM-L Internal code Internal code Kit code bin SSSCCC-BB-HHHH-HGNNNNNNN Vf class B = 6-V class D = 12-V class Reel size 0 = 1000 (standard) Color EZW = EasyWhite SSSCCC-B-WWW-FFF-GAAAAAA Internal code Vf class B = 6-V class D = 12-V class bin Color EZW = EasyWhite 16

17 Reflow Soldering Characteristics In testing, Cree has found XLamp XM-L EasyWhite LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used, and therefore it is the lamp or luminaire manufacturer s responsibility to determine applicable soldering requirements. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. T P Ramp-up t P Critical Zone T L to T P Temperature T L Ts max Ts min ts Preheat t S Ramp-down 25 t 25 C to Peak Time Profile Feature Average Ramp-Up Rate (Ts max to T p ) Lead-Free Solder 1.2 C/second Preheat: Temperature Min (Ts min ) 120 C Preheat: Temperature Max (Ts max ) 170 C Preheat: Time (ts min to ts max ) seconds Time Maintained Above: Temperature (T L ) 217 C Time Maintained Above: Time (t L ) seconds Peak/Classification Temperature (Tp) C Time Within 5 C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25 C to Peak Temperature seconds 1-6 C/second 4 minutes max. Note: All temperatures refer to the topside of the package, measured on the package body surface. 17

18 Notes Measurements The luminous flux, radiant power, chromaticity, forward voltage and CRI measurements in this document are binning specifications only and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors that are not within Cree s control and are not intended or provided as operational specifications for the products. Calculated values are provided for informational purposes only and are not intended or provided as specifications. Pre Release Qualification Testing Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp LEDs and details of Cree s pre-release qualification testing for XLamp LEDs. Lumen Maintenance Cree now uses standardized IES LM and TM methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document. Please read the Long-Term Lumen Maintenance application note for more details on Cree s lumen maintenance testing and forecasting. Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture Sensitivity Cree recommends keeping XLamp LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering. Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity. Once the MBP is opened, XLamp XM-L EasyWhite LEDs may be stored as MSL 1 per JEDEC J-STD-033, meaning they have unlimited floor life in conditions of 30 ºC/85% relative humidity (RH). Regardless of storage condition, Cree recommends sealing any unsoldered LEDs in the original MBP. RoHS Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, RoHS Declarations for this product can be obtained from your Cree representative or from the Product Ecology section of the Cree website. REACh Compliance REACh substances of very high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA) has published notice of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative to insure you get the most up-to-date REACh SVHC Declaration. REACh banned substance information (REACh Article 67) is also available upon request. 18

19 Notes - Continued UL Recognized Component This product meets the requirements to be considered a UL Recognized Component with Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/UL Vision Advisory WARNING. Do not look at an exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please refer to the LED Eye Safety application note. 19

20 Mechanical Dimensions Thermal vias, if present, are not shown on these drawings. All measurements are ±.13 mm unless otherwise indicated Top View Anode R2.26 Side View Bottom View Recommended PCB Solder Pad Recommended Stencil Pattern (Shaded Area Is Open) 20

21 Tape and Reel All Cree carrier tapes conform to EIA-481D, Automated 6 Component 5 Handling Systems 4 Standard. D NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON WITHOUT THE WRITTEN CONSENT OF CREE INC. 2.00[.079] 2.00[.079] P2 P2 4.00[.157] 4.00[.157] Po Po Do Do [ ] [ ] 1.75[.069] E1 1.75[.069] E1 3 REV 2 1 REVISIONS DESCRIPTION BY DATE All dimensions in mm. POCKET SIZE Ao mm [.213"] Bo mm [.213"] Ko mm [.132"] APP'D D C [.13 Ko 5.50[.217]F 5.50[.217]F 12.00[.472] NOMINAL 12.00[.472] NOMINAL [.484] [.484] [.404] MAX [.404] MAX E2 W E2 W [.213] Bo C 5.40[.213] Ao 8.00[.315] 8.00[.315] P P 1.50[.059] D1 1.50[.059] D1.36[.014] T B B User Feed Direction 7.0 END Trailer 160mm (min) of empty pockets sealed with tape (15 pockets min.) 4 8 CATHODE SIDE START 3.35[.132] Ko ANODE SIDE A Loaded Pockets (1000 Lamps) [.213] Ao THIRD ANGLE PROJECTION Leader 400mm (min.) of empty pockets with at least 100mm sealed by tape (40 empty pockets min.) 4 12 CREE REFERENCE DRAWING FOR TEK-PAK DRAWING UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND AFTER FINISH. TOLERANCE UNLESS SPECIFIED:.XX ±.01.XXX ±.005 X ±.5 FOR SHEET METAL PARTS ONLY.X ±.06.XX ±.03.XXX ±.010 X ±.5 DRAWN BY D. CRONIN CHECK APPROVED MATERIAL DATE DATE DATE FINAL PROTECTIVE FINISH 4/23/10 DRAWING SCALE 1 / SURFACE FINISH: TITLE SIZE SCALE A DRAWING NO Silicon Drive Durham, N.C Phone (919) Fax (919) XM 5050 CARRIER TAPE SHEET OF REV. A A MEASURED AT HUB MEASURED AT HUB 1.9±.4 21± ± MEASURED AT EDGE

22 Packaging Unpackaged Reel Packaged Reel Label with Cree Bin Code, Quantity, Reel ID Label with Cree, Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Boxed Reel Label with Cree, Quantity, Reel ID, PO # Patent Label Label with Cree Bin Code, Quantity, Reel ID 22