To show how to determine the forces in the members of a truss using the method of joints and the method of sections.
|
|
- Samuel Park
- 5 years ago
- Views:
Transcription
1 5 Chapter Objectives To show how to determine the forces in the members of a truss using the method of joints and the method of sections. To analyze the forces acting on the members of frames and machines composed of pin-connected members.
2 In-Class Activities 1. Reading Quiz 2. Simple Trusses 3. The Method of Joints 4. Zero-Force Members 5. The Method of Sections 6. Frames and Machines 7. Concept Quiz
3
4 SIMPLE TRUSSES A truss composed of slender members joined together at their end points Planar Trusses Planar trusses are used to support roofs and bridges Roof load is transmitted to the truss at joints by means of a series of purlins
5 SIMPLE TRUSSES (cont) Planar Trusses The analysis of the forces developed in the truss members is 2D Similar to roof truss, the bridge truss loading is also coplanar
6 SIMPLE TRUSSES (cont) Assumptions for Design 1. All loadings are applied at the joint - Weight of the members neglected 2. The members are joined together by smooth pins - Assume connections provided the center lines of the joining members are concurrent
7 SIMPLE TRUSSES (cont) Simple Truss Form of a truss must be rigid to prevent collapse The simplest form that is rigid or stable is a triangle
8 METHOD OF JOINTS Please refer to the website for the animation: Free-body Diagram for an A-Frame For truss, we need to know the force in each member Forces in the members are internal forces For external force members, equations of equilibrium can be applied Force system acting at each joint is coplanar and concurrent F x = 0 and F y = 0 must be satisfied for equilibrium
9 METHOD OF JOINTS (cont) Procedure for Analysis Draw the FBD with at least 1 known and 2 unknown forces Find the external reactions at the truss support Determine the correct sense of the member Orient the x and y axes Apply F x = 0 and F y = 0 Use known force to analyze the unknown forces
10 EXAMPLE 1 Determine the force in each member of the truss and indicate whether the members are in tension or compression.
11 EXAMPLE 1 (cont) Solution 2 unknown member forces at joint B 1 unknown reaction force at joint C 2 unknown member forces and 2 unknown reaction forces at point A For Joint B, F 500N F F F BC y x cos45 0; BC sin 45 0; N F BA N 0 F 0 F BA BC 707.1N ( C) 500N( T )
12 EXAMPLE 1 (cont) Solution For Joint C, F F F C y CA y x 0; 707.1cos45 0; 707.1sin 45 N N 0 0 C y F CA 500N( T ) 500N For Joint A, F 500N F 500N y x 0; Ax 0 0; A 0 y A A x y 500N 500N
13 EXAMPLE 1 (cont) Solution FBD of each pin shows the effect of all the connected members and external forces applied to the pin FBD of each member shows only the effect of the end pins on the member
14 ZERO-FORCE MEMBERS Method of joints is simplified using zero-force members Zero-force members are supports with no loading In general, when 3 members form a truss joint, the 3 rd member is a zero-force member provided no external force or support reaction is applied to the joint
15 EXAMPLE 2 Using the method of joints, determine all the zero-force members of the Fink roof truss. Assume all joints are pin connected.
16 EXAMPLE 2 (cont) Solution For Joint G, F y 0 F 0 GC GC is a zero-force member. For Joint D, F x 0 F 0 DF
17 EXAMPLE 2 (cont) Solution For Joint F, F 90 y, F 0 F FC 0 FC cos 0 For Joint B, F F BH x 0 2kN 2kN F BH 0
18 EXAMPLE 2 (cont) Solution F HC satisfies Fy = 0 and therefore HC is not a zero-force member.
19 THE METHOD OF SECTIONS Used to determine the loadings within a body If a body is in equilibrium, any part of the body is in equilibrium To find forces within members, an imaginary section is used to cut each member into 2 and expose each internal force as external
20 THE METHOD OF SECTIONS Consider the truss and section a-a as shown Please refer to the website for the animation: Free-Body Diagram for a Truss Member forces are equal and opposite to those acting on the other part Newton s Law
21 THE METHOD OF SECTIONS Procedure for Analysis Free-Body Diagram Decide the section of the truss Determine the truss s external reactions Use equilibrium equations to solve member forces at the cut session Draw FBD of the sectioned truss which has the least number of forces acting on it Find the sense of an unknown member force Equations of Equilibrium Summed moments about a point Find the 3 rd unknown force from moment equation
22 EXAMPLE 3 Determine the force in members GE, GC, and BC of the truss. Indicate whether the members are in tension or compression.
23 EXAMPLE 3 (cont) Solution Choose section a-a since it cuts through the three members Draw FBD of the entire truss F M A F y x 0; 0; 0; 400N 1200N(8m) 400N(3m) D A y A x 0 A 1200N 900N x 400N 0 y A (12m) y 300N 0 D y 900N
24 EXAMPLE 3 (cont) Solution Draw FBD for the section portion M M G C F 0; 0; y 0; 300N(4m) 400N(3m) F 300N(8m) F 300N 3 5 F GC GE (3m) 0 F 0 F GC BC (3m) 0 F GE 500N( T) BC 800N( C) 800N( T)
25 FRAMES AND MACHINES Composed of pin-connected multi-force members Frames are stationary Apply equations of equilibrium to each member to determine the unknown forces
26 FRAMES AND MACHINES (cont) Free-Body Diagram Isolate each part by drawing its outlined shape show all forces and couple moments that act on the part identify each known and unknown force and couple moment indicate any dimensions apply equations of equilibrium assume sense of unknown force or moment draw FBD
27 EXAMPLE 3 For the frame, draw the free-body diagram of (a) each member, (b) the pin at B and (c) the two members connected together.
28 EXAMPLE 3 Solution Part (a) BA and BC are not two-force AB is subjected to the resultant forces from the pins
29 EXAMPLE 3 Solution Part (b) Pin at B is subjected to two forces, force of the member BC and AB on the pin For equilibrium, forces and respective components must be equal but opposite Bx and By shown equal and opposite on members AB
30 EXAMPLE 3 Solution Part (c) Bx and By are not shown as they form equal but opposite internal forces Unknown force at A and C must act in the same sense Couple moment M is used to find reactions at A and C
31 Example 4: Solution: By inspection it can be seen that AB is a two force member. The FBD is
32 Example 5:
33 Solution:
34 Example 6: Determine the components of the forces acting on each member of the frame shown. Solution:
35 Example 6: (cont)
36 Example 7
37 Solution 1 Solution 2
38
39
40
41
42
43
44 CONCEPT QUIZ 1) Truss ABC is changed by decreasing its height from H to 0.9H. Width W and load P are kept the same. Which one of the following statements is true for the revised truss as compared to the original truss? a) Forces in all its members have decreased. b) Forces in all its members have increased. c) Forces in all its members have remained the same. d) None of the above.
45 CONCEPT QUIZ (cont) 2) For this truss, determine the number of zero-force members. a) 0 F b) 1 F c) 2 d) 3 e) 4
46 CONCEPT QUIZ (cont) 3) Can you determine the force in member ED by making the cut at section a-a? Explain your answer. a) No, there are 4 unknowns. b) Yes, using MD = 0. c) Yes, using ME = 0. d) Yes, using MB = 0.
47 CONCEPT QUIZ (cont) 4) If you know F ED, how will you determine F EB? a) By taking section b-b and using ME = 0 b) By taking section b-b, and using FX = 0 and FY = 0 c) By taking section a-a and using MB = 0 d) By taking section a-a and using MD = 0
48 CONCEPT QUIZ (cont) 5) As shown, a cut is made through members GH, BG and BC to determine the forces in them. Which section will you choose for analysis and why? a) Right, fewer calculations. b) Left, fewer calculations. c) Either right or left, same amount of work. d) None of the above, too many unknowns.
49 CONCEPT QUIZ (cont) 6) When determining the force in member HG in the previous question, which one equation of equilibrium is best to use? a) MH = 0 b) MG = 0 c) MB = 0 d) MC = 0
50 CONCEPT QUIZ (cont) 7) When determining the reactions at joints A, B, and C, what is the minimum number of unknowns for solving this problem? a) 3 b) 4 c) 5 d) 6
51 CONCEPT QUIZ (cont) 8) For the same problem, imagine that you have drawn a FBD of member AB. What will be the easiest way to write an equation involving unknowns at B? a) MC = 0 b) MB = 0 c) MA = 0 d) FX = 0
Chapter 6: Structural Analysis
Chapter 6: Structural Analysis APPLICATIONS Trusses are commonly used to support a roof. For a given truss geometry and load, how can we determine the forces in the truss members and select their sizes?
More informationAnnouncements. Trusses Method of Joints
Announcements Mountain Dew is an herbal supplement Today s Objectives Define a simple truss Trusses Method of Joints Determine the forces in members of a simple truss Identify zero-force members Class
More informationREADING QUIZ. 2. When using the method of joints, typically equations of equilibrium are applied at every joint. A) Two B) Three C) Four D) Six
READING QUIZ 1. One of the assumptions used when analyzing a simple truss is that the members are joined together by. A) Welding B) Bolting C) Riveting D) Smooth pins E) Super glue 2. When using the method
More informationLecture 20. ENGR-1100 Introduction to Engineering Analysis THE METHOD OF SECTIONS
ENGR-1100 Introduction to Engineering Analysis Lecture 20 THE METHOD OF SECTIONS Today s Objectives: Students will be able to determine: 1. Forces in truss members using the method of sections. In-Class
More informationENGR-1100 Introduction to Engineering Analysis. Lecture 20
ENGR-1100 Introduction to Engineering Analysis Lecture 20 Today s Objectives: THE METHOD OF SECTIONS Students will be able to determine: 1. Forces in truss members using the method of sections. In-Class
More informationChapter 6: Structural Analysis
Chapter 6: Structural Analysis Chapter Objectives To show how to determine the forces in the members of a truss using the method of joints and the method of sections. To analyze the forces acting on the
More informationENGR-1100 Introduction to Engineering Analysis. Lecture 19
ENGR-1100 Introduction to Engineering Analysis Lecture 19 SIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS Today s Objectives: Students will be able to: In-Class Activities: a) Define a simple
More informationEngineering Mechanics: Statics STRUCTURAL ANALYSIS. by Dr. Ibrahim A. Assakkaf SPRING 2007 ENES 110 Statics
CHAPTER Engineering Mechanics: Statics STRUCTURAL ANALYSIS College of Engineering Department of Mechanical Engineering Tenth Edition 6a by Dr. Ibrahim A. Assakkaf SPRING 2007 ENES 110 Statics Department
More informationME Statics. Structures. Chapter 4
ME 108 - Statics Structures Chapter 4 Outline Applications Simple truss Method of joints Method of section Germany Tacoma Narrows Bridge http://video.google.com/videoplay?docid=-323172185412005564&q=bruce+lee&pl=true
More information6.6 FRAMES AND MACHINES APPLICATIONS. Frames are commonly used to support various external loads.
6.6 FRAMES AND MACHINES APPLICATIONS Frames are commonly used to support various external loads. How is a frame different than a truss? How can you determine the forces at the joints and supports of a
More informationSRSD 2093: Engineering Mechanics 2SRRI SECTION 19 ROOM 7, LEVEL 14, MENARA RAZAK
SRSD 2093: Engineering Mechanics 2SRRI SECTION 19 ROOM 7, LEVEL 14, MENARA RAZAK SIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS Today s Objectives: Students will be able to: a) Define a simple
More informationENGR-1100 Introduction to Engineering Analysis. Lecture 23
ENGR-1100 Introduction to Engineering Analysis Lecture 23 Today s Objectives: Students will be able to: a) Draw the free body diagram of a frame and its members. FRAMES b) Determine the forces acting at
More informationStatics: Lecture Notes for Sections
Chapter 6: Structural Analysis Today s Objectives: Students will be able to: a) Define a simple truss. b) Determine the forces in members of a simple truss. c) Identify zero-force members. READING QUIZ
More informationEquilibrium Equilibrium and Trusses Trusses
Equilibrium and Trusses ENGR 221 February 17, 2003 Lecture Goals 6-4 Equilibrium in Three Dimensions 7-1 Introduction to Trusses 7-2Plane Trusses 7-3 Space Trusses 7-4 Frames and Machines Equilibrium Problem
More informationLecture 23. ENGR-1100 Introduction to Engineering Analysis FRAMES S 1
ENGR-1100 Introduction to Engineering Analysis Lecture 23 Today s Objectives: Students will be able to: a) Draw the free body diagram of a frame and its members. FRAMES b) Determine the forces acting at
More informationEngineering Mechanics: Statics in SI Units, 12e
Engineering Mechanics: Statics in SI Units, 12e 5 Equilibrium of a Rigid Body Chapter Objectives Develop the equations of equilibrium for a rigid body Concept of the free-body diagram for a rigid body
More informationSIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS
SIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS Today s Objectives: Students will be able to: a) Define a simple truss. b) Determine the forces in members of a simple truss. c) Identify zero-force
More informationNewton s Third Law Newton s Third Law: For each action there is an action and opposite reaction F
FRAMES AND MACHINES Learning Objectives 1). To evaluate the unknown reactions at the supports and the interaction forces at the connection points of a rigid frame in equilibrium by solving the equations
More informationChapter Objectives. Copyright 2011 Pearson Education South Asia Pte Ltd
Chapter Objectives To develop the equations of equilibrium for a rigid body. To introduce the concept of the free-body diagram for a rigid body. To show how to solve rigid-body equilibrium problems using
More informationFRAMES AND MACHINES Learning Objectives 1). To evaluate the unknown reactions at the supports and the interaction forces at the connection points of a
FRAMES AND MACHINES Learning Objectives 1). To evaluate the unknown reactions at the supports and the interaction forces at the connection points of a rigid frame in equilibrium by solving the equations
More informationEQUATIONS OF EQUILIBRIUM & TWO-AND THREE-FORCE MEMEBERS
EQUATIONS OF EQUILIBRIUM & TWO-AND THREE-FORCE MEMEBERS Today s Objectives: Students will be able to: a) Apply equations of equilibrium to solve for unknowns, and, b) Recognize two-force members. READING
More information7 STATICALLY DETERMINATE PLANE TRUSSES
7 STATICALLY DETERMINATE PLANE TRUSSES OBJECTIVES: This chapter starts with the definition of a truss and briefly explains various types of plane truss. The determinancy and stability of a truss also will
More informationEQUATIONS OF EQUILIBRIUM & TWO- AND THREE-FORCE MEMEBERS
EQUATIONS OF EQUILIBRIUM & TWO- AND THREE-FORCE MEMEBERS Today s Objectives: Students will be able to: a) Apply equations of equilibrium to solve for unknowns, and, b) Recognize two-force members. In-Class
More informationENGR-1100 Introduction to Engineering Analysis. Lecture 13
ENGR-1100 Introduction to Engineering Analysis Lecture 13 EQUILIBRIUM OF A RIGID BODY & FREE-BODY DIAGRAMS Today s Objectives: Students will be able to: a) Identify support reactions, and, b) Draw a free-body
More informationChapter 5 Equilibrium of a Rigid Body Objectives
Chapter 5 Equilibrium of a Rigid Bod Objectives Develop the equations of equilibrium for a rigid bod Concept of the free-bod diagram for a rigid bod Solve rigid-bod equilibrium problems using the equations
More informationPlane Trusses Trusses
TRUSSES Plane Trusses Trusses- It is a system of uniform bars or members (of various circular section, angle section, channel section etc.) joined together at their ends by riveting or welding and constructed
More informationENGINEERING MECHANICS STATIC
Trusses Simple trusses The basic element of a truss is the triangle, three bars joined by pins at their ends, fig. a below, constitutes a rigid frame. The term rigid is used to mean noncollapsible and
More informationOutline: Frames Machines Trusses
Outline: Frames Machines Trusses Properties and Types Zero Force Members Method of Joints Method of Sections Space Trusses 1 structures are made up of several connected parts we consider forces holding
More informationIn this chapter trusses, frames and machines will be examines as engineering structures.
In the previous chapter we have employed the equations of equilibrium in order to determine the support / joint reactions acting on a single rigid body or a system of connected members treated as a single
More informationCHAPTER 5 ANALYSIS OF STRUCTURES. Expected Outcome:
CHAPTER ANALYSIS O STRUCTURES Expected Outcome: Able to analyze the equilibrium of structures made of several connected parts, using the concept of the equilibrium of a particle or of a rigid body, in
More informationENT 151 STATICS. Contents. Introduction. Definition of a Truss
CHAPTER 6 Analysis ENT 151 STATICS Lecture Notes: Mohd Shukry Abdul Majid KUKUM of Structures Contents Introduction Definition of a Truss Simple Trusses Analysis of Trusses by the Method of Joints Joints
More informationIshik University / Sulaimani Architecture Department. Structure. ARCH 214 Chapter -5- Equilibrium of a Rigid Body
Ishik University / Sulaimani Architecture Department 1 Structure ARCH 214 Chapter -5- Equilibrium of a Rigid Body CHAPTER OBJECTIVES To develop the equations of equilibrium for a rigid body. To introduce
More informationEquilibrium of a Particle
ME 108 - Statics Equilibrium of a Particle Chapter 3 Applications For a spool of given weight, what are the forces in cables AB and AC? Applications For a given weight of the lights, what are the forces
More informationSTATICS VECTOR MECHANICS FOR ENGINEERS: Eleventh Edition CHAPTER. Ferdinand P. Beer E. Russell Johnston, Jr. David F. Mazurek
Eleventh E 6 Analysis CHAPTER VECTOR MECHANICS OR ENGINEERS: STATICS erdinand P. Beer E. Russell Johnston, Jr. David. Mazurek of Structures Contents Application Introduction Definition of a Truss Simple
More informationSimilar to trusses, frames are generally fixed, load carrying structures.
Similar to trusses, frames are generally fixed, load carrying structures. The main difference between a frame and a truss is that in a frame at least one member is a multi force member (çoklu kuvvet elemanı).
More informationChapter 3 Trusses. Member CO Free-Body Diagram. The force in CO can be obtained by using section bb. Equations of Equilibrium.
Chapter 3 Trusses Procedure for analysis 1 Free body diagram: make a decision as to how to cut or section the truss through the members where forces are to be determined. 2 Equation of equilibrium: apply
More informationCHAPTER 5 Statically Determinate Plane Trusses
CHAPTER 5 Statically Determinate Plane Trusses TYPES OF ROOF TRUSS TYPES OF ROOF TRUSS ROOF TRUSS SETUP ROOF TRUSS SETUP OBJECTIVES To determine the STABILITY and DETERMINACY of plane trusses To analyse
More informationCHAPTER 5 Statically Determinate Plane Trusses TYPES OF ROOF TRUSS
CHAPTER 5 Statically Determinate Plane Trusses TYPES OF ROOF TRUSS 1 TYPES OF ROOF TRUSS ROOF TRUSS SETUP 2 ROOF TRUSS SETUP OBJECTIVES To determine the STABILITY and DETERMINACY of plane trusses To analyse
More informationCHAPTER 2: EQUILIBRIUM OF RIGID BODIES
For a rigid body to be in equilibrium, the net force as well as the net moment about any arbitrary point O must be zero Summation of all external forces. Equilibrium: Sum of moments of all external forces.
More informationME 201 Engineering Mechanics: Statics
ME 201 Engineering Mechanics: Statics Unit 7.1 Simple Trusses Method of Joints Zero Force Members Simple Truss structure composed of slender members joined together at their end points Planar Truss Simple
More informationMEE224: Engineering Mechanics Lecture 4
Lecture 4: Structural Analysis Part 1: Trusses So far we have only analysed forces and moments on a single rigid body, i.e. bars. Remember that a structure is a formed by and this lecture will investigate
More informationMethod of Sections for Truss Analysis
Method of Sections for Truss Analysis Notation: (C) = shorthand for compression P = name for load or axial force vector (T) = shorthand for tension Joint Configurations (special cases to recognize for
More informationEquilibrium of a Rigid Body. Engineering Mechanics: Statics
Equilibrium of a Rigid Body Engineering Mechanics: Statics Chapter Objectives Revising equations of equilibrium of a rigid body in 2D and 3D for the general case. To introduce the concept of the free-body
More information3.1 CONDITIONS FOR RIGID-BODY EQUILIBRIUM
3.1 CONDITIONS FOR RIGID-BODY EQUILIBRIUM Consider rigid body fixed in the x, y and z reference and is either at rest or moves with reference at constant velocity Two types of forces that act on it, the
More informationEQUATIONS OF EQUILIBRIUM & TWO- AND THREE-FORCE MEMBERS
EQUATIONS OF EQUILIBRIUM & TWO- AND THREE-FORCE MEMBERS Today s Objectives: Students will be able to: a) Apply equations of equilibrium to solve for unknowns, and, b) Recognize two-force members. APPLICATIONS
More informationThe centroid of an area is defined as the point at which (12-2) The distance from the centroid of a given area to a specified axis may be found by
Unit 12 Centroids Page 12-1 The centroid of an area is defined as the point at which (12-2) The distance from the centroid of a given area to a specified axis may be found by (12-5) For the area shown
More informationENG202 Statics Lecture 16, Section 7.1
ENG202 Statics Lecture 16, Section 7.1 Internal Forces Developed in Structural Members - Design of any structural member requires an investigation of the loading acting within the member in order to be
More informationCalculating Truss Forces. Method of Joints
Calculating Truss Forces Method of Joints Forces Compression body being squeezed Tension body being stretched Truss truss is composed of slender members joined together at their end points. They are usually
More informationP.E. Civil Exam Review:
P.E. Civil Exam Review: Structural Analysis J.P. Mohsen Email: jpm@louisville.edu Structures Determinate Indeterminate STATICALLY DETERMINATE STATICALLY INDETERMINATE Stability and Determinacy of Trusses
More informationThe analysis of trusses Mehrdad Negahban (1999)
The analysis of trusses Mehrdad Negahban (1999) A truss: A truss is a structure made of two force members all pin connected to each other. The method of joints: This method uses the free-body-diagram of
More informationthree Point Equilibrium 1 and planar trusses ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2014 lecture
ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SUMMER 2014 lecture three point equilibrium http:// nisee.berkeley.edu/godden and planar trusses Point Equilibrium 1 Equilibrium balanced
More informationChapter 5: Equilibrium of a Rigid Body
Chapter 5: Equilibrium of a Rigid Body Chapter Objectives To develop the equations of equilibrium for a rigid body. To introduce the concept of a free-body diagram for a rigid body. To show how to solve
More informationEQUILIBRIUM OF A RIGID BODY & FREE-BODY DIAGRAMS
Today s Objectives: Students will be able to: EQUILIBRIUM OF A RIGID BODY & FREE-BODY DIAGRAMS a) Identify support reactions, and, b) Draw a free-body diagram. In-Class Activities: Check Homework Reading
More informationPin-Jointed Frame Structures (Frameworks)
Pin-Jointed rame Structures (rameworks) 1 Pin Jointed rame Structures (rameworks) A pin-jointed frame is a structure constructed from a number of straight members connected together at their ends by frictionless
More informationEQUATIONS OF EQUILIBRIUM & TWO- AND THREE-FORCE MEMBERS
EQUATIONS OF EQUILIBRIUM & TWO- AND THREE-FORCE MEMBERS Today s Objectives: Students will be able to: a) Apply equations of equilibrium to solve for unknowns b) Identify support reactions c) Recognize
More informationWhen a rigid body is in equilibrium, both the resultant force and the resultant couple must be zero.
When a rigid body is in equilibrium, both the resultant force and the resultant couple must be zero. 0 0 0 0 k M j M i M M k R j R i R F R z y x z y x Forces and moments acting on a rigid body could be
More informationAnnouncements. Equilibrium of a Rigid Body
Announcements Equilibrium of a Rigid Body Today s Objectives Identify support reactions Draw a free body diagram Class Activities Applications Support reactions Free body diagrams Examples Engr221 Chapter
More informationSTATICS. Bodies. Vector Mechanics for Engineers: Statics VECTOR MECHANICS FOR ENGINEERS: Design of a support
4 Equilibrium CHAPTER VECTOR MECHANICS FOR ENGINEERS: STATICS Ferdinand P. Beer E. Russell Johnston, Jr. Lecture Notes: J. Walt Oler Texas Tech University of Rigid Bodies 2010 The McGraw-Hill Companies,
More informationEQUATIONS OF EQUILIBRIUM & TWO- AND THREE-FORCE MEMEBERS
EQUATIONS OF EQUILIBRIUM & TWO- AND THREE-FORCE MEMEBERS Today s Objectives: Students will be able to: a) Apply equations of equilibrium to solve for unknowns, and b) Recognize two-force members. In-Class
More informationChapter - 1. Equilibrium of a Rigid Body
Chapter - 1 Equilibrium of a Rigid Body Dr. Rajesh Sathiyamoorthy Department of Civil Engineering, IIT Kanpur hsrajesh@iitk.ac.in; http://home.iitk.ac.in/~hsrajesh/ Condition for Rigid-Body Equilibrium
More informationSTATICS. Vector Mechanics for Engineers: Statics VECTOR MECHANICS FOR ENGINEERS: Contents 9/3/2015
6 Analsis CHAPTER VECTOR MECHANICS OR ENGINEERS: STATICS erdinand P. Beer E. Russell Johnston, Jr. of Structures Lecture Notes: J. Walt Oler Texas Tech Universit Contents Introduction Definition of a Truss
More informationChapter 7 INTERNAL FORCES
Chapter 7 INTERNAL FORCES READING QUIZ 1. In a multiforce member, the member is generally subjected to an internal. A) normal force B) shear force C) bending moment D) All of the above. 2. In mechanics,
More informationT R U S S. Priodeep Chowdhury;Lecturer;Dept. of CEE;Uttara University//TRUSS Page 1
T R U S S A truss is a structure that consists of All straight members connected together with pin joints connected only at the ends of the members and All external forces (loads & reactions) must be applied
More information5 Equilibrium of a Rigid Body Chapter Objectives
5 Equilibrium of a Rigid Body Chapter Objectives Develop the equations of equilibrium for a rigid body Concept of the free-body diagram for a rigid body Solve rigid-body equilibrium problems using the
More informationPAT 101 FUNDAMENTAL OF ENGINEERING MECHANICS EQUILIBREQUILIBRIUM OF A RIGID BODY IUM OF A RIGID BODY
PAT 101 FUNDAMENTAL OF ENGINEERING MECHANICS EQUILIBREQUILIBRIUM OF A RIGID BODY IUM OF A RIGID BODY MARDHIAH FARHANA BINT OMAR Week 5-6 EQUILIBRIUM OF A RIGID BODY Conditions for Rigid Equilibrium Free-Body
More informationLecture 0. Statics. Module 1. Overview of Mechanics Analysis. IDeALab. Prof. Y.Y.KIM. Solid Mechanics
Lecture 0. Statics Module 1. Overview of Mechanics Analysis Overview of Mechanics Analysis Procedure of Solving Mechanics Problems Objective : Estimate the force required in the flexor muscle Crandall,
More informationPROBLEM 6.1 SOLUTION. Free body: Entire truss: (3.2 m) (48 kn)(7.2 m) = 0 = = = BC. 60 kn. Free body: Joint B: = kn T. = 144.
PROBLEM 6.1 Using the method of joints, determine the force in each member of the truss shown. State whether each member is in tension or compression. Free bod: Entire truss: Σ F = 0: B = 0 B = 0 Σ M =
More informationWhen a rigid body is in equilibrium, both the resultant force and the resultant couple must be zero.
When a rigid body is in equilibrium, both the resultant force and the resultant couple must be zero. 0 0 0 0 k M j M i M M k R j R i R F R z y x z y x Forces and moments acting on a rigid body could be
More informationCalculating Truss Forces Unit 2 Lesson 2.1 Statics
alculating Truss Forces alculating Truss Forces Principles of Engineering 22 Forces ompression body being squeezed Tension body being stretched Truss truss is composed of slender members joined together
More informationthree Equilibrium 1 and planar trusses ELEMENTS OF ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SPRING 2015 lecture ARCH 614
ELEMENTS OF ARCHITECTURAL STRUCTURES: FORM, BEHAVIOR, AND DESIGN DR. ANNE NICHOLS SPRING 2015 lecture three equilibrium and planar trusses Equilibrium 1 Equilibrium balanced steady resultant of forces
More informationINTERNAL FORCES Today s Objective: Students will be able to: 1. Use the method of sections for determining internal forces in 2-D load cases.
INTERNAL FORCES Today s Objective: Students will be able to: 1. Use the method of sections for determining internal forces in 2-D load cases. In-Class Activities: Check Homework, if any Reading Quiz Applications
More informationMechanics of Materials
Mechanics of Materials 2. Introduction Dr. Rami Zakaria References: 1. Engineering Mechanics: Statics, R.C. Hibbeler, 12 th ed, Pearson 2. Mechanics of Materials: R.C. Hibbeler, 9 th ed, Pearson 3. Mechanics
More informationEngineering Mechanics: Statics in SI Units, 12e
Engineering Mechanics: Statics in SI Units, 12e 3 Equilibrium of a Particle Chapter Objectives To introduce the concept of the free-body diagram for a particle To show how to solve particle equilibrium
More informationVector Mechanics: Statics
PDHOnline Course G492 (4 PDH) Vector Mechanics: Statics Mark A. Strain, P.E. 2014 PDH Online PDH Center 5272 Meadow Estates Drive Fairfax, VA 22030-6658 Phone & Fax: 703-988-0088 www.pdhonline.org www.pdhcenter.com
More informationUnit M1.4 (All About) Trusses
Unit M1.4 (ll bout) Trusses Readings: DL 1.9 16.001/002 -- Unified Engineering Department of eronautics and stronautics Massachusetts Institute of Technology LERNING OBJETIVES FOR UNIT M1.4 Through participation
More informationEngineering Mechanics Statics
Mechanical Systems Engineering _ 2016 Engineering Mechanics Statics 7. Equilibrium of a Rigid Body Dr. Rami Zakaria Conditions for Rigid-Body Equilibrium Forces on a particle Forces on a rigid body The
More informationEQUILIBRIUM OF A RIGID BODY
EQUILIBRIUM OF A RIGID BODY Today s Objectives: Students will be able to a) Identify support reactions, and, b) Draw a free diagram. APPLICATIONS A 200 kg platform is suspended off an oil rig. How do we
More information1. Determine the Zero-Force Members in the plane truss.
1. Determine the Zero-orce Members in the plane truss. 1 . Determine the force in each member of the loaded truss. Use the Method of Joints. 3. Determine the force in member GM by the Method of Section.
More informationEngineering Mechanics Department of Mechanical Engineering Dr. G. Saravana Kumar Indian Institute of Technology, Guwahati
Engineering Mechanics Department of Mechanical Engineering Dr. G. Saravana Kumar Indian Institute of Technology, Guwahati Module 3 Lecture 6 Internal Forces Today, we will see analysis of structures part
More informationName ME 270 Summer 2006 Examination No. 1 PROBLEM NO. 3 Given: Below is a Warren Bridge Truss. The total vertical height of the bridge is 10 feet and each triangle has a base of length, L = 8ft. Find:
More informationNAME: Section: RIN: Tuesday, May 19, :00 11:00. Problem Points Score Total 100
RENSSELAER POLYTECHNIC INSTITUTE TROY, NY FINAL EXAM INTRODUCTION TO ENGINEERING ANALYSIS (ENGR-1100) NAME: Section: RIN: Tuesday, May 19, 2015 8:00 11:00 Problem Points Score 1 20 2 20 3 20 4 20 5 20
More informationSupplement: Statically Indeterminate Trusses and Frames
: Statically Indeterminate Trusses and Frames Approximate Analysis - In this supplement, we consider an approximate method of solving statically indeterminate trusses and frames subjected to lateral loads
More informationMT225 Homework 6 - Solution. Problem 1: [34] 5 ft 5 ft 5 ft A B C D. 12 kips. 10ft E F G
MT225 Homework 6 - Solution Problem 1: [34] 5 ft 5 ft 5 ft C D 10ft 12 kips E G To begin, we need to find the reaction forces at supports and E. To do so, we draw a free-body diagram of the entire structure
More informationthree point equilibrium and planar trusses Equilibrium Equilibrium on a Point Equilibrium on a Point
RHITETURL STRUTURES: FORM, EHVIOR, N ESIGN R. NNE NIHOLS SUMMER 2014 lecture three Equilibrium balanced steady resultant of forces on a particle is 0 X point equilibrium and planar trusses http:// nisee.berkeley.edu/godden
More informationTheory of structure I 2006/2013. Chapter one DETERMINACY & INDETERMINACY OF STRUCTURES
Chapter one DETERMINACY & INDETERMINACY OF STRUCTURES Introduction A structure refers to a system of connected parts used to support a load. Important examples related to civil engineering include buildings,
More informationLOVELY PROFESSIONAL UNIVERSITY BASIC ENGINEERING MECHANICS MCQ TUTORIAL SHEET OF MEC Concurrent forces are those forces whose lines of action
LOVELY PROFESSIONAL UNIVERSITY BASIC ENGINEERING MECHANICS MCQ TUTORIAL SHEET OF MEC 107 1. Concurrent forces are those forces whose lines of action 1. Meet on the same plane 2. Meet at one point 3. Lie
More informationPhysics 8 Friday, November 8, 2013
Physics 8 Friday, November 8, 2013 Turn in HW10 today. I ll put HW11 online tomorrow. Today & Monday: mainly trusses. Some beams next week. Monday reading: from Vossoughi ch5+8 (centroids + second moment
More informationEQUILIBRIUM OF RIGID BODIES IN TWO DIMENSIONS
EQUILIBRIUM OF RIGID BODIES IN TWO DIMENSIONS If the resultant of all external forces acting on a rigid body is zero, then the body is said to be in equilibrium. Therefore, in order for the rigid body
More informationENGI 1313 Mechanics I
ENGI 1313 Mechanics I Lecture 25: Equilibrium of a Rigid Body Shawn Kenny, Ph.D., P.Eng. Assistant Professor Faculty of Engineering and Applied Science Memorial University of Newfoundland spkenny@engr.mun.ca
More informationFE Sta'cs Review. Torch Ellio0 (801) MCE room 2016 (through 2000B door)
FE Sta'cs Review h0p://www.coe.utah.edu/current- undergrad/fee.php Scroll down to: Sta'cs Review - Slides Torch Ellio0 ellio0@eng.utah.edu (801) 587-9016 MCE room 2016 (through 2000B door) Posi'on and
More informationSTATICS. FE Review. Statics, Fourteenth Edition R.C. Hibbeler. Copyright 2016 by Pearson Education, Inc. All rights reserved.
STATICS FE Review 1. Resultants of force systems VECTOR OPERATIONS (Section 2.2) Scalar Multiplication and Division VECTOR ADDITION USING EITHER THE PARALLELOGRAM LAW OR TRIANGLE Parallelogram Law: Triangle
More informationEngineering Mechanics
2019 MPROVEMENT Mechanical Engineering Engineering Mechanics Answer Key of Objective & Conventional Questions 1 System of forces, Centoriod, MOI 1. (c) 2. (b) 3. (a) 4. (c) 5. (b) 6. (c) 7. (b) 8. (b)
More informationSupport Idealizations
IVL 3121 nalysis of Statically Determinant Structures 1/12 nalysis of Statically Determinate Structures nalysis of Statically Determinate Structures The most common type of structure an engineer will analyze
More informationTruss Analysis Method of Joints. Steven Vukazich San Jose State University
Truss nalysis Method of Joints Steven Vukazich San Jose State University General Procedure for the nalysis of Simple Trusses using the Method of Joints 1. raw a Free Body iagram (FB) of the entire truss
More information1. Determine the Zero-Force Members in the plane truss.
1. Determine the Zero-orce Members in the plane truss. 1 . Determine the forces in members G, CG, BC, and E for the loaded crane truss. Use the Method of Joints. 3. Determine the forces in members CG and
More informationCIV100: Mechanics. Lecture Notes. Module 1: Force & Moment in 2D. You Know What to Do!
CIV100: Mechanics Lecture Notes Module 1: Force & Moment in 2D By: Tamer El-Diraby, PhD, PEng. Associate Prof. & Director, I2C University of Toronto Acknowledgment: Hesham Osman, PhD and Jinyue Zhang,
More informationLecture 17 February 23, 2018
Statics - TAM 20 & TAM 2 Lecture 7 ebruary 23, 208 Announcements Monday s lecture: watch for Piazza announcement over weekend for possible change Concept Inventory: Ungraded assessment of course knowledge
More informationIf the number of unknown reaction components are equal to the number of equations, the structure is known as statically determinate.
1 of 6 EQUILIBRIUM OF A RIGID BODY AND ANALYSIS OF ETRUCTURAS II 9.1 reactions in supports and joints of a two-dimensional structure and statically indeterminate reactions: Statically indeterminate structures
More informationCombined Stress. Axial Stress. Axial vs. Eccentric Load Combined Stress Interaction Formulas
Architecture 324 Structures II Combined Stress Axial vs. Eccentric Load Combined Stress Interaction Formulas from Man und Frau den Mond betrachtend 1830-35 by Caspar David Friedrich Alte Nationalgalerie,
More informationLecture 14 February 16, 2018
Statics - TAM 210 & TAM 211 Lecture 14 February 16, 2018 SoonTrending.com Announcements Structured office hours of working through practice problems will be held during Sunday office hours, starting Sunday
More information