Ev r r d Part No.: 83IR85C Features/ Single color/ High Power output/ Low power consumption/ High reliability and long life/ RoHS compliant / RoHS Descriptions/ 9.2 9. 7.9 7.5 Dice material/ AlGaAs Emitting Color/ Infrared Emitting diodes/ Device Outline/ 8mm Round Type/ 8mm Lens Type/ Water Clear/ Directivity/ Relative Luminous 1..5 9 2. 1.5±.5 CATHODE Ta=25 C IF=2mA 6 DIRECTIVITY 3 25.4Min 2.54±.1 Radiation Angle 1.Max.5 ±.1 1. All dimensions are millimeters/ mm. 2. Tolerance is +/-.2mm unless otherwise noted/.2mm. 3.5 6 9 1. 1
Ev r r d Part No.: 83IR85C Absolute maximum ratings/ Ta = 25 Parameter Symbol Values Test Condition Min. Max. Unit Power Dissipation Reverse Voltage Forward Current Operating Temperature Storage Temperature Soldering Temperature P d 1 mw V R I R =1 A 9 V I FM Duty=.1mS 1kHz 1 ma T opr -3 +85 T str -4 +1 T sd t 3sec,2mm from base 26 Electrical and optical characteristics/ Ta = 25 Parameter Forward Voltage Reverse Current Peak Wavelength Spectral Line half-width Radiant Intensity Viewing Angle Symbol Test Condition Values Min. Typ. Max. Unit VF IF = 5mA ---- 1.5 1.8 V IR VR = 9V ---- ---- 1 A p IF = 5mA ---- 85 ---- nm IF = 5mA 45 nm Ie I F =5mA 63 9 mw/sr 2 1/2 IF=2mA ---- 3 ---- deg. 2
Ev r r d Part No.: 83IR85C Typical electrical/optical characteristic curves/ 1 VS 2.5 Fig Forward Current(mA) Forward Current(mA) 8 6 4 2 1 8 6 4 2 1.3 2 4 6 8 1 Ambient Temperature TA ( ) Radiant Intensity(mW/sr) Relative Value at IF=5mA 1.4 1.5 1.6 1.7 Forward Voltage(V) Fig.3 VS. 1 75 Radiant Intensity 2.5 2. 1.5 1..5 2. 1.5 1..5 2 4 6 8 1 IF-Forward Current (ma) -2 Fig.5 VS. Fig.4 VS. 2 4 Ambient Temperature TA ( ) 6 8 1 5 25 5 6 7 8 9 1 11 Wavelength (nm) 3
Ev r r d SPECIFICATION Label Form Specification/ Everred Tech Ltd. P/N Rank / / Qty Date Lot No pcs QC P/N: Customer's Production Number/ QTY: Packing Quantity/ Ranks: Iv / Vf / WD Iv Iv Rank/ Vf Vf Rank/ WD Color Group/ QC: Quality Control chapter/ Date: mm / dd / yy mm Month/dd Date/yy Year/ Lot No: Production batch Number/ Lead Forming/ 1. Any lead forming or bending must be done before soldering. 2. When forming leads, there must be a minimum of 2mm clearance between the base of the LED lens and the lead bend. 2 4
Ev r r d 3. Avoid bending the leads at the same point more than once. 4. During assembly onto PCB, the lead pitch of the LED must match the pitch of the mounting holes on the PCB during component placement. Soldering Condition/ Careful attention should be paid during soldering. When soldering, leave more then 2mm from solder joint to case, and soldering beyond the base of the tie bar is recommended. LED 2mm Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering. LED Recommended soldering conditions/: Hand Soldering Temp.at tip of iron 3 Max.(3WMax.) 3 3 Soldering time 3 sec Max. 3 Distance 2mm Min.(From solder joint to case) 2 Preheat temp. Bath temp. Bath time. DIP Soldering 1 Max. (6 sec Max.) 1 6 26 Max 26. 3 sec Max. 3 Distance 2mm Min 2. 5
Ev r r d Cleaning/ 1. Do not clean LEDs with water, Alcohol are recommended solvents for cleaning. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the resin or not. 2. LEDs may be damaged by ultrasonic-washed. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. LED Storage/ 1. Environmental temperature: -4 ---1, Recommended: -2 ---5-4 ---1-2 ---5 2. Environmental humidity: 3%---7%, Recommended: 4%---6% 3%---7% 4%---6% Static Electricity/ 1. Static Electricity or power surge will damage the LED. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. LED 2. All production machinery and test instruments must be electrically grounded. 6
Ev r r d 3. Maintain a humidity level of 5% or higher in production areas. 5% 4. Use anti-static packaging for transport and storage. Notes/ 1. This datasheet will be update regularly, if there comes out any changes, pls confirmed by the latest datasheet., 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. Everred assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 7