Reversible reactions Some reactions do not go to completion we don t get 100% yield because not all of the reactants react to form products. One of the reasons for this is that some reactions are reversible the products can react to form the reactants! e.g. 3 H 2 + N 2 2 NH 3 but also 2 NH 3 N 2 + 3 H 2 We use a special symbol to denote a reaction which is reversible: 3 H 2 + N 2 2 NH 3 A single arrow in an equation means that the reactants form the products but the products can t react to form the original reactants again. e.g. CaCO 3 CaO + CO 2 (thermal decomposition of calcium carbonate) The double-headed arrow means the reaction can go in either direction e.g. NH 4 Cl NH 3 + HCl (ammonium chloride reacts to form ammonia and hydrogen chloride and also ammonia and hydrogen chloride react to form ammonium chloride)
thermal decomposition NH 4 Cl NH 3 + HCl NH 3 + HCl NH 4 Cl neutralisation Heat The forward reaction is a thermal decompostition ammonium chloride breaks up when heated into two simpler substances: ammonia and hydrogen chloride. The reverse reaction is a neutralisation the hydrogen chloride is acting as an acid (H + donor) and the ammonia as a base (H + acceptor).
A reversible reaction the test for water: White, anhydrous copper sulphate forms blue hydrated copper sulphate if water is added. The reaction is reversible. If the crystals are heated they turn white as anhydrous copper sulphate is formed. CuSO 4.5H 2 O (s) CuSO 4(s) + 5H 2 O (l) hydrated anhydrous + water copper sulphate copper sulphate An alternative test for water: Blue, anhydrous cobalt chloride is also used as a test for water it turns to pink hydrated cobalt chloride if water is added. If the crystals are heated they turn blue again. CoCl 2.6H 2 O (s) CoCl 2(s) + 6H 2 O (l) hydrated anhydrous + water cobalt chloride cobalt chloride
Equilibrium When reactants are turning into products, and products are turning into reactants, a dynamic equilibrium can be set up. (Think of this as being like a balance-point the forward and reverse reactions becoming balanced. Running up an escalator which is going down at a rate causing you to stay in the same place would be one example of a dynamic equilibrium. Adjusting the flow into and out of the pot so that the volume of liquid remains the same even though the actual liquid is constantly changing, would be another example) At equilibrium: There will be both products and reactants present in a mixture. The rate of products turning into reactants will be the same as the rate of reactants turning into products. To get an equilibrium, none of the reactants or products must escape you need a closed system.
How it works: The reactants begin to react forming products. The initial rate of forward reaction will be fast. The forward reaction slows down as reactants are used up. Products have now been formed, so they begin to react to form reactants. The initial rate of the reverse reaction is very slow as only a few product particles are present. As more products are formed, the rate of the reverse reaction increases. Eventually the rates of forward reaction and backward reactions become the same. THE REACTIONS HAVEN T FINISHED BUT AN EQUILIBRIUM IS SET UP.
How much is there at equilibrium? The amounts of the products and the reactants at equilibrium depends on the conditions (e.g. temperature, pressure). Changing the conditions will change the amounts of reactants and products present in the mixture - a new equilibrium gets set up. We call this changing the POSITION of the equilibrium. - if changing the conditions causes the position of equilibrium to move in the forward direction (to the right) we get more products, less reactants in the equilibrium mixture N 2 + 3H 2 2NH 3 - if changing the conditions causes the position of equilibrium to move in the backwards direction (to the left) we get less products, more reactants in the equilibrium mixture N 2 + 3H 2 2NH 3
Making more product at equilibrium Whenever we change the conditions, the position of the equilibrium will shift to try and oppose the change. N.B. The effect of pressure only applies to GASES in the balanced equation!
Example: CH 3 OH (g) + H 2 O (g) CO 2(g) + 3H 2(g) endothermic in the forward direction This reaction is called steam reforming of methanol. It is used to produce hydrogen, a valuable fuel, from an alcohol. What would be the best conditions of temperature and pressure to get the best yield of hydrogen? Temperature: Pressure: Catalyst: A high temperature would move the position of equilibrium in the endothermic direction, which is the forward direction, so more products would be made. There are four moles of gases on the right side of the equation and only two moles of gases on the left side. A low pressure would move the position of equilibrium in the forward direction, making more product. A catalyst would speed up the reaction (in both directions) so products would be made sooner. It would have no effect on the position of equilibrium, and hence the yield, only how quickly the product is made.
True or False? All chemical reactions are reversible. FALSE burning, and rusting, for example, can t be reversed The mass can change if a solid product is formed in a closed system FALSE all the same atoms are still there, mass is conserved Equilibrium can only happen in closed systems. TRUE a closed system is a requirement for an equilibrium In a reversible reaction, reactants can form products and products can form reactants. TRUE this is exactly what does happen A symbol shows that an equilibrium has been set up. FALSE it only shows that the reaction is reversible Once at equilibrium no more products are formed. FALSE the reactions happen continuously, so product is still being made, but it is being used up by the reverse reaction at the same rate. Once at equilibrium, the forward and backward reactions stop. FALSE these reactions continue, but at the same rate
Industrial Processes In industry, we want sustainable development using the products as efficiently as possible to minimise use of energy (economic) and minimise waste products (environmental). We can optimise reaction conditions to get as much product as possible in the reaction mixture, and to do so using the minimum amount of energy practical. To do this we need to consider: - temperature - pressure - removing products as they are formed - use of catalysts
The Haber Process for the production of ammonia. N 2(g) + 3 H 2(g) 2 NH 3(g) nitrogen + hydrogen ammonia Raw materials: - nitrogen (N 2 ) which is obtained from the air (by fractional distillation of air) - hydrogen (H 2 ) which is mainly obtained from the cracking of hydrocarbons, or from natural gas and steam: CH 4(g) + H 2 O (g) CO (g) + 3 H 2(g) Conditions: iron catalyst; temperature of about 450 C; pressure of about 200 atmospheres (a fairly high pressure)
Energy Changes in reversible reactions Reversible reactions are exothermic (give out heat) in one direction and endothermic (take in heat) in the other. The same amount (Joules) of heat energy is given out in one direction and taken in in the other direction. exothermic N 2 + 3H 2 2NH 3 nitrogen + hydrogen ammonia endothermic
Uses of ammonia Ammonia is a very important substance, used in huge quantities for making nitric acid and for manufacturing products such as: Fertilisers Explosives Dyes Medicines
How the Haber process works: By cooling and condensing the ammonia to remove it as a liquid, then recycling the unreacted gases: Reactants are used efficiently, not wasted Energy used to make reactants is not wasted A reasonable yield of ammonia is made as quickly as possible
Why use a temp. of 450ºC for the Haber process? Heat energy is given out when ammonia is formed the forward reaction is exothermic N 2 + 3H 2 2NH 3 ΔH is negative If we do the reaction at a low temperature then we should get more ammonia in the reaction mixture at equilibrium. BUT the rate of reaction is too slow at low temperatures. We therefore use a moderate temperature as a compromise in order to make ammonia quickly enough to be economical. We also use a catalyst to speed up the reaction rather than more heat, so the process is more energy efficient. The catalyst has no effect on the %conversion.
Why use a pressure of about 200 atmospheres? 4 moles of gas turn into 2 moles of gas when ammonia is formed: N 2 + 3H 2 2NH 3 less molecules of gas on RHS If we carry out the reaction at high pressure then we will get more ammonia in the reaction mixture at equilibrium. In addition the rate of reaction will increase. BUT high pressures - take a lot of energy to create - require greater safety precautions to prevent leaks or explosions. We therefore use a moderately high pressure as a compromise.
The Contact Process For the production of sulphuric acid. Raw materials: - sulphur, S, which is obtained from local refineries where it has been recovered from oil and gas (fossil fuels) - oxygen, O 2 which is obtained by drying and compressing air. Conditions: Vanadium(V) oxide (V 2 O 5 ) catalyst; temperature of about 450 C; pressure of about 2 atmospheres.
There are three stages to the process: Stage 1: making sulphur dioxide The sulphur is burnt: S (l) + O 2(g) SO 2(g) Stage 2: making sulphur trioxide The sulphur dioxide and oxygen are heated to 450 C with the vanadium(v) oxide catalyst and pressurised to 2 atmospheres. An equilibrium is formed: 2 SO 2(g) + O 2(g) 2 SO 3(g) Stage 3: making sulphuric acid The sulphur trioxide goes through a series of reactions to form sulphuric acid: SO 3(g) + H 2 SO 4(l) H 2 S 2 O 7(l) H 2 S 2 O 7(l) + H 2 O (l) 2 H 2 SO 4(aq) The sulphuric acid is then further diluted to the concentration required.
Uses of sulphuric acid Making fertilisers e.g. ammonium sulphate Making detergents (including shampoos and liquid soaps) Making paints (to extract the white pigment, titanium oxide from its ores)
Why use a temp. of 450ºC for the Contact process? Heat energy is given out when sulphur trioxide is formed the forward reaction is exothermic 2 SO 2 + O 2 2 SO 3 ΔH is negative If we do the reaction at a low temperature then we should get more SO 3 in the reaction mixture at equilibrium. BUT the rate of reaction is too slow at low temperatures. We therefore use a moderate temperature as a compromise in order to make sulphur trioxide quickly enough to be economical. We also use a catalyst to speed up the reaction rather than more heat, so the process is more energy efficient.
Why use a pressure of about 2 atmospheres? 3 moles of gas turn into 2 moles of gas when sulphur trioxide is formed: 2 SO 2 + O 2 2 SO 3 less molecules of gas on RHS If we carry out the reaction at high pressure then we will get more sulphur trioxide in the reaction mixture at equilibrium; in addition the rate of reaction will increase. The conversion of SO 2 into SO 3 is already so good (99.5%) in this case that a higher pressure than 2 atmospheres (which is quite a low pressure really) is not needed. The catalyst has no effect on the %conversion, but helps to speed up the reaction, as it would be too slow to be economically viable without.
Alternative raw material Instead of burning sulphur, another way of making sulphur dioxide is to roast a sulphide ore such as iron pyrites in excess air: 4 FeS 2(s) + 11 O 2(g) 2 Fe 2 O 3(s) + 8 SO 2(g) Once the sulphur dioxide has been made, the other two stages of the Contact Process are the same. Iron pyrites