CMOS Digital Integrated Circuits TC7SZ08FU Silicon Monolithic TC7SZ08FU 1. Functional Description 2-Input AND Gate 2. Features (1) AEC-Q100 (Rev. ) (Note 1) (2) Wide operating temperature range: T opr = -40 to 125 (Note 2) (3) igh output current: ±24 ma (min) at CC = (4) Super high speed operation: t pd = 2.7 (typ.) at CC = 5.0, C = 50 pf (5) Operation voltage range: CC = to (6) tolerant inputs (7) power down protection output (8) Matches the performance of TC74CX series when operated at 3.3 CC Note 1: This device is compliant with the reliability requirements of AEC-Q100. For details, contact your Toshiba sales representative. Note 2: For devices with the ordering part number ending in J(CT. T opr = -40 to 85 for the other devices. 3. Packaging US 1 Start of commercial production 1998-08 Rev.
4. Marking and Pin Assignment Marking Pin Assignment (Top view) 5. IEC ogic 6. Truth Table A B Y 7. Absolute imum Ratings (Note) (Unless otherwise specified, T a = 25 ) Note Rating Supply voltage Input voltage DC output voltage Input diode current Output diode current DC output current CC /ground current Power dissipation Storage temperature CC IN OUT I IK I OK I OUT I CC P D T stg (Note 1) (Note 2) (Note 3) - to 6.0 - to 6.0 - to 6.0 - to CC + -20-20 ±50 ±50 200-65 to 150 Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditio (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability andbook ( andling Precautio / Derating Concept and Methods ) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: CC = 0 Note 2: igh () or ow () state. I OUT absolute maximum rating must be observed. Note 3: OUT < GND ma ma ma ma mw 2 Rev.
8. Operating Ranges (Note) Note Rating Supply voltage Input voltage Output voltage Operating temperature Input rise and fall time CC IN OUT T opr dt/dv (Note 1) (Note 2) (Note 3) (Note 4) (Note 5) CC = 1.8 ± 5, 2.5 ± 0.2 CC = CC = Note: The operating ranges must be maintained to eure the normal operation of the device. Unused inputs must be tied to either CC or GND. Note 1: Data retention only Note 2: CC = 0 Note 3: igh () or ow () state. Note 4: For devices with the ordering part number ending in J(CT. Note 5: For devices except those with the ordering part number ending in J(CT. 9. Electrical 9.1. DC (Unless otherwise specified, T a = 25 ) to 1.5 to 0 to 0 to 0 to CC -40 to 125-40 to 85 0 to 20 0 to 10 0 to 5 / CC () Typ. igh-level input voltage I to 1.95 CC 8 to CC 0.75 ow-level input voltage I to 1.95 CC 2 to CC 0.25 igh-level output voltage O IN = I I O = -100 1.55 2.9 4.4 I O = -8 ma 1.9 2.15 I O = -16 ma 2.4 2.8 I O = -24 ma 2.68 I O = -32 ma 3.8 4.2 ow-level output voltage O IN = I or I I O = 100 0.0 0.0 0.0 0.0 I O = 8 ma 0.3 I O = 16 ma 5 0.4 I O = 24 ma 0.22 5 I O = 32 ma 0.22 5 Input leakage current I IN IN = or GND 0 to ±1.0 Power-OFF leakage current I OFF IN or OUT = 0 1 Quiescent supply current I CC IN = CC or GND 2 3 Rev.
9.2. DC (Unless otherwise specified, T a = -40 to 85 ) CC () igh-level input voltage I to 1.95 CC 8 to CC 0.75 ow-level input voltage I to 1.95 CC 2 to CC 0.25 igh-level output voltage O IN = I I O = -100 1.55 2.9 4.4 I O = -8 ma 1.9 I O = -16 ma 2.4 I O = -24 ma I O = -32 ma 3.8 ow-level output voltage O IN = I or I I O = 100 I O = 8 ma 0.3 I O = 16 ma 0.4 I O = 24 ma 5 I O = 32 ma 5 Input leakage current I IN IN = or GND 0 to ±10.0 Power-OFF leakage current I OFF IN or OUT = 0 10 Quiescent supply current I CC IN = CC or GND 20 4 Rev.
9.3. DC (Note) (Unless otherwise specified, T a = -40 to 125 ) CC () igh-level input voltage I to 1.95 CC 8 to CC 0.75 ow-level input voltage I to 1.95 CC 2 to CC 0.25 igh-level output voltage O IN = I I O = -100 1.55 2.9 4.4 I O = -8 ma 1.7 I O = -16 ma I O = -24 ma 2.0 I O = -32 ma 3.4 ow-level output voltage O IN = I or I I O = 100 I O = 8 ma 0.45 I O = 16 ma 0.6 I O = 24 ma I O = 32 ma Input leakage current I IN IN = or GND 0 to ±20.0 Power-OFF leakage current I OFF IN or OUT = 0 100 Quiescent supply current I CC IN = CC or GND 200 Note: For devices with the ordering part number ending in J(CT. 5 Rev.
9.4. AC (Unless otherwise specified, T a = 25,, Input: t r = t f = 3 ) Propagation delay time Input capacitance Power dissipation capacitance t P,t P C IN C PD Note (Note 1) Test Condition R = 1 MΩ R = 500 Ω CC () 1.8 ± 5 2.5 ± 0.2 0 to 3.3 C (pf) Note 1: C PD is defined as the value of the internal equivalent capacitance which is calculated from the operating current coumption without load. Average operating current can be obtained by the equation. I CC(opr) = C PD CC f IN + I CC 9.5. AC (Unless otherwise specified, T a = -40 to 85,, Input: t r = t f = 3 ) 15 50 2.0 1.5 Typ. 5.2 3.4 2.6 3.3 2.7 4 20 25 10.0 7.0 4.7 4.1 5.2 pf pf CC () C (pf) Propagation delay time t P,t P R = 1 MΩ 1.8 ± 5 15 2.0 1 2.5 ± 0.2 7.5 5.0 4.4 R = 500 Ω 50 1.5 4.8 9.6. AC (Note) (Unless otherwise specified, T a = -40 to 125,, Input: t r = t f = 3 ) CC () C (pf) Propagation delay time t P,t P R = 1 MΩ 1.8 ± 5 15 2.0 12.0 2.5 ± 0.2 8.5 5.0 R = 500 Ω 50 1.5 6.5 Note: For devices with the ordering part number ending in J(CT. 6 Rev.
Package Dimeio : mm Weight: 0.006 g (typ.) Package Name(s) JEDEC: SOT-353 Nickname: US 7 Rev.
RESTRICTIONS ON PRODUCT USE Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. This document and any information herein may not be reproduced without prior written permission from TOSIBA. Even with TOSIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. Though TOSIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are respoible for complying with safety standards and for providing adequate desig and safeguards for their hardware, software and systems which minimize risk and avoid situatio in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create desig including the Product, or incorporate the Product into their own applicatio, customers must also refer to and comply with (a) the latest versio of all relevant TOSIBA information, including without limitation, this document, the specificatio, the data sheets and application notes for Product and the precautio and conditio set forth in the "TOSIBA Semiconductor Reliability andbook" and (b) the itructio for the application with which the Product will be used with or for. Customers are solely respoible for all aspects of their own product design or applicatio, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applicatio; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such desig and applicatio. TOSIBA ASSUMES NO IABIITY FOR CUSTOMERS' PRODUCT DESIGN OR APPICATIONS. PRODUCT IS NEITER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS TAT REQUIRE EXTRAORDINARIY IG EES OF QUAITY AND/OR REIABIITY, AND/OR A MAFUNCTION OR FAIURE OF WIC MAY CAUSE OSS OF UMAN IFE, BODIY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBIC IMPACT ("UNINTENDED USE"). Except for specific applicatio as expressly stated in this document, Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trai, ships and other traportation, traffic signaling equipment, equipment used to control combustio or explosio, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE PRODUCT FOR UNINTENDED USE, TOSIBA ASSUMES NO IABIITY FOR PRODUCT. For details, please contact your TOSIBA sales representative. Do not disassemble, analyze, reverse-engineer, alter, modify, tralate or copy Product, whether in whole or in part. Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulatio. The information contained herein is presented only as guidance for Product use. No respoibility is assumed by TOSIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No licee to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROIDED IN TE REEANT TERMS AND CONDITIONS OF SAE FOR PRODUCT, AND TO TE MAXIMUM EXTENT AOWABE BY AW, TOSIBA (1) ASSUMES NO IABIITY WATSOEER, INCUDING WITOUT IMITATION, INDIRECT, CONSEQUENTIA, SPECIA, OR INCIDENTA DAMAGES OR OSS, INCUDING WITOUT IMITATION, OSS OF PROFITS, OSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND OSS OF DATA, AND (2) DISCAIMS ANY AND A EXPRESS OR IMPIED WARRANTIES AND CONDITIONS REATED TO SAE, USE OF PRODUCT, OR INFORMATION, INCUDING WARRANTIES OR CONDITIONS OF MERCANTABIITY, FITNESS FOR A PARTICUAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapo or missile technology products (mass destruction weapo). Product and related software and technology may be controlled under the applicable export laws and regulatio including, without limitation, the Japanese Foreign Exchange and Foreign Trade aw and the U.S. Export Administration Regulatio. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulatio. Please contact your TOSIBA sales representative for details as to environmental matters such as the RoS compatibility of Product. Please use Product in compliance with all applicable laws and regulatio that regulate the inclusion or use of controlled substances, including without limitation, the EU RoS Directive. TOSIBA ASSUMES NO IABIITY FOR DAMAGES OR OSSES OCCURRING AS A RESUT OF NONCOMPIANCE WIT APPICABE AWS AND REGUATIONS. 8 Rev.