Submitted by: Monroe Sorton ATech Educator News Copyright ATech Training, Inc. Electricity Made Simple Part 2 of 3 1 November 2016 Electrical current is expressed in units of amperes (A). One ampere is said to be present when approximately 6.24 quintillion electrons (6,240,000,000,000,000,000) cross a specific point within the electrical pathway in one second. A quantity of 6.24 x 10 18 electrons is said to be equivalent to one coulomb of charge. Research suggests that The International System of Units named this quantity of charge after Charles Augustin de Coulomb (1736-1806; French physicist). Although electrons are not visible to the naked eye, the effects of electricity can be realized by the presence of heat, light, electromagnetic force, effects of fire, sensation, and by measuring instruments such as digital volt ohmmeters (DVOM) and oscilloscopes. Rearranging electrons disproportionately within a structured device called a battery creates a potential voltage force in the same manner that stretching a rubber band creates a potential elastic force. The longer the length of the rubber band is stretched, the more potential elastic force (energy) will be released as the rubber band snaps back to its original resting position and form. Likewise, the more electrons that are disproportionately accumulated on one of the two conductive plate(s) within a battery, the more electrons will be available and naturally return to the vacant electron positions in the valence rings from where they were moved. These vacancy positions are sometimes called holes. The more electrons are displaced and accumulated, the more potential, or voltage, will exist. Atoms deprived of free electrons are called ions due to the imbalanced state caused by missing free electrons from the valence rings. In order to re-establish equilibrium or balance within the ion, free electrons must return to fill the vacancies or holes in the valence rings of the ions. The strong natural tendency for electrons to return to the holes in the valence rings of ions constitute an electrical state of charge called voltage or electrical potential. Voltage is expressed in units of volts (V) attributed to Alessandro Volta (1745-1827; Italian scientist and physicist). Since all the electrons travel in one direction to return to the ions on one of the two plate(s) in a battery, it is called a direct current source or DC battery source. The current only flows in one direction. When a stretched rubber band is released, its elasticity contracts as it snaps back to its original position. The force of the contraction is proportionate to the length and force of the stretch. If the same rubber band is stretched and released beneath water, the rubber band will experience a slower contraction rate as it snaps back to its original resting position. Contraction rate is now compromised due to the opposing force offered by the presence and substance of water. The water will offer opposition to the rubber band s contrac- Electricity Made Simple, Part 2 of 3 Continued on Page 2...
conductor. Insulators are constructed of atoms with five or more electrons in the valence rings. The resistance offered to the flow of electrons in insulated material is extremely high. However, extremely high voltages can still overcome high resistance and force electrons to move away from the valence rings of atoms, causing the temperature of the pathway to increase rapidly and resulting in electrical pathway destruction. Lightning is a perfect example of high voltages overcoming the electrical resistance of the air. tion rate. If the same process is repeated with the rubber band submerged in a thicker gel-like substance, the rubber band s contraction rate will experience additional opposing forces from the gel-like substance. The thicker the gel-like substance, the more opposition or physical resistance to the rubber band effect. Materials constructed of atoms with free electrons in the valence ring are called conductors. For example, copper, silver, gold, iron, nickel, and aluminum are examples of conductors. Conductors provide a pathway for electrons to travel to their intended destination with minimum opposition. As electrons travel back to their original destination (ions), they will always encounter some degree of electrical opposition called electrical resistance. Electrical resistance is expressed in units of ohms, attributed to Georg Simon Ohm. With the exception of absolute zero, electrons will always encounter some degree of resistance in all electrical conductors. Factors affecting electrical resistance are the size of the cross section areas of the conductor, the length of the conductor, the temperature of the conductor, and the specific resistivity of the By explaining the basic concepts of electricity and providing real-life examples involving the dynamics of electricity, students begin to connect the dots and understand what electricity is really all about; what allows a battery to be fully charged and what causes a battery to be discharged. The distinction between charged batteries versus dead batteries is comparable to a stretched rubber band versus a rubber band that is not stretched. Stretching the rubber band awakens the potential elastic force in the rubber band material while displacing and accumulating electrons disproportionately establishes a potential voltage charge within a battery. There is no potential energy in a rubber band when it is not stretched. There is no potential voltage between atoms in a state of equilibrium. Natural laws, and the laws of physics and chemistry, allow for science to use natural principles of chemistry to cause electrons to accumulate disproportionately between two conductive plate(s). The difference between the number of electrons on the negative plate(s) and the positive plate(s) generates an electrical charge within the battery. Whenever any two different conductive materials are placed into an acidic solution or substance called electrolyte, a natural chemical reaction will occur. This chemical reaction causes electrons to move and accumulate disproportionately on one of the two conductive plates more so than the other. The plate that accumulates excessive electrons is considered to be the negative plate(s) or 2 Electricity Made Simple, Part 2 of 3 Continued on Page 3...
terminal of the battery and the conductive plate(s) that loses or is deprived of the equivalent number of electrons is considered to be the positive plate(s) or terminal of the battery. The chemical reaction enables the electrons to leave the plate(s) of one terminal and accumulate on the plate(s) of the other terminal. Students can see and experience the concept of a battery by inserting two different types of conductive material into an acidic solution; i.e. a brass screw and a galvanized screw can be used as plates/terminals inserted into an acidic solution (body of electrolyte) such as a lemon or a potato. Students can use a DVOM to measure the potential voltage of approximately 600 to 1,000 millivolts (mv) that will develop across the brass and galvanized screw terminals of the lemon/potato-based battery. They can connect a light emitting diode (LED) to the correct polarity on the terminals of the lemon/potato battery and see the LED light as the electrons flow from the lemon/potato battery. Students are always fascinated by live demonstrations. They get the opportunity to witness and experience the most fundamental electrical charge emanating from a fruit or vegetable. The voltage generated will primarily depend on the size and type of conductive screws or plates used and the specific gravity of the acidic solution as compared to water. One of the two screws will become the positive terminal and the other will become the negative terminal. Students can use a DVOM to verify which screw became the negative or positive terminal of the lemon/potato battery. The test leads of the DVOM can be switched between both screw terminals until a negative sign appears on the screen of the DVOM. This will identify the polarity of the screw terminals of the lemon/potato battery. Students will learn the significance of polarity. If a conductive pathway is provided to allow all displaced and accumulated electrons to return to their original destination, the battery will then be considered discharged or dead. Electrons will flow or travel from the negative terminal to the positive terminal via any electrical conductive pathway. When electrons flow from the negative to the positive terminal of the battery, this is called the electron flow. The conventional flow is based on the assumption that electrons flow from the positive terminal to the negative terminal of the battery. Should a higher voltage be required, several lemon/potato batteries can be connected in series; positive screw terminals connected to the negative screw terminals. This will cause the total voltage to double or triple for each lemon/potato battery connected in series. Recharging a dead automotive battery is accomplished by using an external electrical source called a battery charger. Recharging a battery is comparable to stretching a rubber band again and again. When free electrons are pushed away from the valence rings of the original atom on the positive plate(s) and collected disproportionately on the negative plate(s) of the battery, the battery is re-charged. Potential elastic force is established in a rubber band, and potential voltage is established between the terminals of a battery. Unfortunately, after stretching a rubber band repeatedly, it will eventually fail. Likewise, after recharging an automotive battery repeatedly, the battery will also fail. Students will be able to connect these demonstrations and experiences to what they have learned. Look for Part 3 of this article in December s ATech Educator News. Questions or Comments: Monroe Sorton, Automotive Instructor General Automotive and NISSAN msorton@gwinnetttech.edu Work: 678-226-6261 Cell: 770-882-3316 3
Lighting System (model 821C) * Preliminary Design The ATech Lighting System Trainer (model 821C) is designed to teach computer and network-controlled automotive lighting system operation. This trainer allows for instructor demonstration, student hands-on reinforcement, and troubleshooting practice. Powered by a 12VDC automotive battery or a 12VDC/23AMP (minimum) power supply (not included). Features: New vehicle components, connectors, and factory wire colors. Provides an advanced level of instruction by duplicating actual on-vehicle troubleshooting procedures. Intermittent and hard faults can be inserted using the Instructor Management Program (IMP) via a computer connected to the trainer or over the ATech Lab System (ALS). Hard faults can be inserted by using the built in keypad on the Power Windows System Trainer. Ability to perform actual service manual test procedures. Compatible with ATech s Instructor Management Program (IMP). Courseware includes Instructor Guide, Student Manual, and Service Manual Information. Battery posts are protected against polarity reversal. Includes external power supply for uninterrupted fault operation. User interface displays built-in scan tool data. Call Now to Place your Order (Press 2 for Sales) ATech Training, Inc. 12290 Chandler Drive Walton, KY 41094 Toll Free: 1-888-738-9924 Phone: 859-485-7229 Fax: 859-485-7299 E-mail: sales@atechtraining.com www.atechtraining.com 4 Automotive Technology
Available for Immediate Delivery Wiper / Washer System The ATech Wiper/Washer System Trainer (model 830FJ) is designed to teach computer and network controlled automotive witper/washer system operation. This trainer allows for instuctor demonstration, student hands-on reinforcement and troubleshooting practice. Powered by a 12VDC automotive battery or a 12VDC/23A power supply (not included). Power Windows System The ATech Power Windows System Trainer (model 840FJ) is designed to teach computer and network controlled automotive power window operation. This trainer allows for instuctor demonstration, student handson reinforcement and troubleshooting practice. Powered by a 12VDC automotive battery or a 12VDC/23A power supply (not included). Call Now to Place your Order (Press 2 for Sales) ATech Training, Inc. 12290 Chandler Drive Walton, KY 41094 Toll Free: 1-888-738-9924 Phone: 859-485-7229 Fax: 859-485-7299 E-mail: sales@atechtraining.com www.atechtraining.com 5 Automotive Technology
Follow Us! Stay up-to-date with all the latest information and resources. /atechtraining /company/atech-training-inc @ATechTraining /ATechTraining ATech Training is a Member of: Scholarships Available A Veteran Owned and Operated American Company Automotive Technology View Us On Your Mobile Phone www.atechtraining.com 6 ATech Training, Inc. 12290 Chandler Drive Walton, KY 41094 Toll Free: 1-888-738-9924 Phone: 859-485-7229 E-mail: sales@atechtraining.com Website: www.atechtraining.com