Wind Tunnel Tests of the Counter-Rotating Propeller of. Stratospheric Airship. Peiqing Liu 1, a, Jingwei Sun 2,b and Zhihao Tang 3,c

Similar documents
Two-Dimensional Moving Blade Row Interactions in a Stratospheric Airship Contra-Rotating Open Propeller Configuration

Performance. 5. More Aerodynamic Considerations

Transonic Aerodynamics Wind Tunnel Testing Considerations. W.H. Mason Configuration Aerodynamics Class

Research on Propeller Characteristics of Tip Induced Loss

ScienceDirect. Experimental Validation on Lift Increment of a Flapping Rotary Wing with Boring-hole Design

A simplified model for a small propeller with different airfoils along the blade

1082. Computational study on aerodynamic characteristics of a flying wing MAV

AEROSPACE ENGINEERING

Propeller theories. Blade element theory

Rotor reference axis

SIMULATION STUDIES OF MICRO AIR VEHICLE

Research on Balance of Unmanned Aerial Vehicle with Intelligent Algorithms for Optimizing Four-Rotor Differential Control

1. Introduction Some Basic Concepts

Small-Scale Propellers Operating in the Vortex Ring State

ME 425: Aerodynamics

Computational Fluid Dynamics Study Of Fluid Flow And Aerodynamic Forces On An Airfoil S.Kandwal 1, Dr. S. Singh 2

A STUDY ON AERODYNAMIC DESIGN OF HIGH- EFFICIENCY PROPELLERS AT HIGH-ALTITUDE

Investigation on the influence of scaling effects in propeller testing through the use of theoretical prediction codes

Definitions. Temperature: Property of the atmosphere (τ). Function of altitude. Pressure: Property of the atmosphere (p). Function of altitude.

Introduction to Flight

Design of Propeller Blades For High Altitude

Overall Performance Design of Ramjet for Combined Engine

Investigation on Boundary Layer Ingestion Propulsion for UAVs

Mathematical Modeling of the Flow behind Propeller

ENGR 4011 Resistance & Propulsion of Ships Assignment 4: 2017

Aerodynamics Simulation of Hypersonic Waverider Vehicle

The E80 Wind Tunnel Experiment the experience will blow you away. by Professor Duron Spring 2012

An Experimental Validation of Numerical Post-Stall Aerodynamic Characteristics of a Wing

A Micro-Sized Ornithopter Wing Design

FLIGHT DYNAMICS. Robert F. Stengel. Princeton University Press Princeton and Oxford

Research Article Investigation on Improved Correlation of CFD and EFD for Supercritical Airfoil

CHAPTER 3 ANALYSIS OF NACA 4 SERIES AIRFOILS

Lecture No. # 09. (Refer Slide Time: 01:00)

COMPUTATIONAL SIMULATION OF THE FLOW PAST AN AIRFOIL FOR AN UNMANNED AERIAL VEHICLE

Introduction to Aerospace Engineering

Introduction to Aerodynamics. Dr. Guven Aerospace Engineer (P.hD)

AAE 520 Experimental Aerodynamics Aero & Space Technology. Products & Services. In collaboration with. Space Tango Kentucky, USA

Coupled Fluid and Heat Flow Analysis Around NACA Aerofoil Profiles at Various Mach Numbers

NI\SI\ Low-Speed Wind-Tunnel Tests of Single- and Counter-Rotation Propellers. NASA Technical Memorandum 87656

NUMERICAL OPTIMIZATION OF THE SHAPE OF A HOLLOW PROJECTILE

Syllabus for AE3610, Aerodynamics I

December 1991 Technical Memorandum. A series of wind tunnel experiments was conducted to study the eect of propeller solidity and thrust axis

A LOW ORDER METHOD FOR CO-AXIAL PROPELLER AND ROTOR PERFORMANCE PREDICTION

The Role of Modelling in Engineering Design. John Fitzpatrick Professor of Mechanical Engineering Trinity College Dublin

Research on Dynamic Stall and Aerodynamic Characteristics of Wind Turbine 3D Rotational Blade

886. Aeroacoustic noise reduction design of a landing gear structure based on wind tunnel experiment and simulation

DESIGN AND ANALYSIS METHODS FOR UAV ROTOR BLADES

NUMERICAL SIMULATION AND MODELING OF UNSTEADY FLOW AROUND AN AIRFOIL. (AERODYNAMIC FORM)

AEROSPACE ENGINEERING DEPARTMENT. Second Year - Second Term ( ) Fluid Mechanics & Gas Dynamics

Experimental Verification of Rudder Control Method Based on Yaw Moment Observer for Electric Skycars in Driving Mode

Experimental Studies on Complex Swept Rotor Blades

Transition Modeling Activities at AS-C²A²S²E (DLR)

Propellers and Ducted Fans

The Study on Re Effect Correction for Laminar Wing with High Lift

Dynamometry Tutorial IMECE

Middle East Technical University Department of Mechanical Engineering ME 305 Fluid Mechanics I Fall 2018 Section 4 (Dr.

ADVERSE REYNOLDS NUMBER EFFECT ON MAXIMUM LIFT OF TWO DIMENSIONAL AIRFOILS

A Numerical Study of Circulation Control on a Flapless UAV

Aero-Propulsive-Elastic Modeling Using OpenVSP

Aerodynamic Investigation of a 2D Wing and Flows in Ground Effect

NUMERICAL INVESTIGATION OF VERTICAL AXIS WIND TURBINE WITH TWIST ANGLE IN BLADES

The S411, S412, and S413 Airfoils

Basic Information to Help Select the Correct Propeller

Brenda M. Kulfan, John E. Bussoletti, and Craig L. Hilmes Boeing Commercial Airplane Group, Seattle, Washington, 98124

Surface flow visualization of a side-mounted NACA 0012 airfoil in a transonic Ludwieg tube

AE 2020: Low Speed Aerodynamics. I. Introductory Remarks Read chapter 1 of Fundamentals of Aerodynamics by John D. Anderson

Experimental Evaluation of Aerodynamics Characteristics of a Baseline Airfoil

Fluid structure interaction dynamic analysis of a mixed-flow waterjet pump

Aerodynamic Design of VTOL MAV

Notes 4: Differential Form of the Conservation Equations

A STUDENT'S INTRODUCTION TO THE WRIGHT BROTHERS WIND TUNNEL AT MIT. Eugene E. Covert T. Wilson Professor Emeritus INTRODUCTION

CHAPTER 4 OPTIMIZATION OF COEFFICIENT OF LIFT, DRAG AND POWER - AN ITERATIVE APPROACH

Study on Numerical Simulation Method of Gust Response in Time Domain Jun-Li WANG

voith.com Precise and safe maneuvering Voith Schneider Propeller

ME 6139: High Speed Aerodynamics

Chapter 5 Wing design - selection of wing parameters 2 Lecture 20 Topics

1976. Numerical computation and optimization design of pantograph aerodynamic noise

OpenFOAM Simulations for MAV Applications

Far Field Noise Minimization Using an Adjoint Approach

RECENT near-sonic and low-sonic boom transport aircraft

Experimental Study on Flow Control Characteristics of Synthetic Jets over a Blended Wing Body Configuration

Aeroelastic Analysis of Engine Nacelle Strake Considering Geometric Nonlinear Behavior

Autonomous Robotic Vehicles

A MORE COMPREHENSIVE DATABASE FOR PROPELLER PERFORMANCE VALIDATIONS AT LOW REYNOLDS NUMBERS. A Dissertation by. Armin Ghoddoussi

DEPARTMENT OF AEROSPACE ENGINEERING, IIT MADRAS M.Tech. Curriculum

Multi Rotor Scalability

Acoustic Noise Prediction and Reduction Reasearch of Helicopter Ducted Tail Rotor

UNSTEADY AERODYNAMIC ANALYSIS OF HELICOPTER ROTOR BY USING THE TIME-DOMAIN PANEL METHOD

Detached Eddy Simulation on Hypersonic Base Flow Structure of Reentry-F Vehicle

Lecture-4. Flow Past Immersed Bodies

LONGITUDINAL STABILITY AND TRIM OF AN ARIANE 5 FLY-BACK BOOSTER

Calibration Methods for an Aerolab 375 Sting Balance to be used in Wind Tunnel Testing

Asymmetry Features Independent of Roll Angle for Slender Circular Cone

Given the water behaves as shown above, which direction will the cylinder rotate?

Aerodynamic Performance Characterization of Leading Edge Protrusions on Small Propellers

Fluid Mechanics III. 1. Dimensional analysis and similarity

Aerodynamic Measurement on the High Speed Test Track

Introduction and Basic Concepts

Experimental analysis of the radiated noise from a small propeller

Concept: AERODYNAMICS

Transcription:

Wind Tunnel Tests of the Counter-Rotating Propeller of Stratospheric Airship Peiqing Liu 1, a, Jingwei Sun 2,b and Zhihao Tang 3,c School of Aeronautic Science and Engineering, Beijing University of Aeronautics and Astronautics, Beijing 100191, China a charmingwei0703@gmail.com, b lpq@buaa.com, c sunjingwei59@sina.com Keywords: stratospheric airship; counter rotating propeller; wind tunnel tests; advanced ratio

Abstract:In this paper, a design of counter-rotating propeller (CRP) for stratospheric airship in low Reynolds number is tested in experiment for the first time. In consideration of stratosphere environment, a two-bladed counter-rotating propeller is designed for stratospheric airship. With the similarity theory of Reynolds number and advanced ratio, the experiment is conducted in low Reynolds number wind tunnel at Beihang University. The results indicate that counter-rotating propeller were 4%-7% percent more efficient than single-rotating propeller (SRP). This shows that for the counter-rotating propeller: 1) with the same diameter and power, the thrust coefficient is higher; 2) with the same thrust coefficient and power coefficient, the diameter could be reduced; 3) with the same thrust coefficient and diameter, the power coefficient could be reduced. Introduction Stratospheric airship is now received more and more attention. Stratospheric airship need to meet the requirements of long-endurance. So there are many methods are adopted: 1) improve the ability of energy storage; 2) use the lighter materials; 3) improve the airship aerodynamic configuration [1] [2]. As a fact, the propeller for stratospheric airship has low efficiency than the propeller for high speed aircraft. Due to the stratosphere atmospheric density is small, Reynolds number of stratosphere is an order of magnitude smaller than the ground. The propeller propulsion for the stratosphere airship has low efficiency[3] [4]. Some existing methods to raise the capacity of the propeller propulsion: At first, can by changing propeller diameter, but due to the stratosphere critical Mach number is small, blade tip is easy to produces shock resistance, bigger blades bring great difficulty to install; Secondly, increase the number of the propeller can effectively improve the overall thrust, but too much consider the layout and balance the propeller torque, installation also has a lot of difficulties; At last, the counter-rotating propeller (CRP) offers the potential of a higher efficiency, smaller diameter along with a reduction of reaction torque when compared with a single rotation propeller (SRP) for equal input horsepower. This is due to the recovery of swirl energy by the rear rotor and the partial cancellation of moments since they are in opposite directions on the front and the rear rotors although not equal in magnitude[5]. Biermann and Gray took a wind tunnel experiment for counter-rotating propeller with high Reynolds number, verified that counter-rotating propeller can significantly improve efficiency[6] [7]. Biermann and Hartman took an experiments prove that counter-rotating propeller propulsion system for the overall efficiency significantly increase applies to lower advance ratio[8] [9]. Airship propeller propulsion works at a low advance ratio. As the energy increasingly nervous today, counter-rotating propeller propulsion applied to stratosphere airship has a good prospect. Similarity Theory Stratospheric air density is much smaller than the ground. How to simulation the low Re number environment on the ground must be studied first before taking the wind tunnel test. In this experiment, in order to ensure the movement similar and dynamic similar the advance ratio and Reynolds number similar conditions must be satisfied[10]. Advance ratio similarity determines the propeller working state movement is similar. The ratio of wind speed and the blade tip rotation speed is called advanced ratio. V 01 V 02 = D 1ns1 D 2n s 2 (2.1) Dynamic similarity requires that various forces acting on the fluid particle is proportional to the size and in the same direction. In general, the fluid particle by forces include: unsteady inertia force, viscous force, gravity, elastic force. Ma number is the ratio of elastic force and inertial force, and it is also the ratio of air velocity and speed of sound. The Ma number similar conditions are the same to the advanced ratio similarity. For air, the gravity can be neglected. As a result, the Re number similarity become the most important condition. Re number is the ratio of inertia force and viscous

force. W D R e = ν 1 1 2 2 = (2.2) 1 W is the resultant velocity of the propeller blade element, νis the dynamic viscosity coefficient(20 km altitude:ν=16.1 10-5m2/s, on the ground: ν=1.46 10-5m2/s). As the resultant velocity W is related to the blade tip speed, the formula (2.2) can be written as: 2 2 ν D / ν ν D ν 2 (2.3) Wind tunnel device In this simulation, the propeller model is similar geometrical properties as those in reference [11] because of the lack of the appropriate data for low Re number CRP. The geometrical properties of this propeller were basically to achieve the highest single rotating propeller (SRP) efficiency and therefore it is not optimal for CRP[5]. Propeller diameter is 0.75m, SRP is two blade, CRP is 2 2. Low Reynolds number and high lift S1223 airfoils was chosen as the blade element.crp 2 2propeller is shown in figure 1 W D ν s 1 1 1 = s 2 2 / 2 Figure. 1 counter-rotating propeller This experiment was taken in low Reynolds number wind tunnel of buaa, as it is shown in figure 3.1. Experimental section diameter is 1.0m, the wind speed V0=0 20m/s, turbulence: k=1%, contraction ratioη=1.44. Figure. 2 low Reynolds number wind tunnel The motor speed and data collection were controlled by the CRP experiment system operated under the LabView. Servo motor is used to control the revolving speed of the propeller. Strain gauge balance is installed on the propeller shaft to measure the force and moment. The

result of a measurement is the averaging of 20 real-time signal value collected in the 4 seconds sampling period. Experimental condition is shown on the chart1:space between two rotor is 150mm, setting angle of blade is 28.3,two rotors used the same speed. Wind speed (m/s) Chart. 1 experimental condition Rotate speed(rpm) Time interval (rpm) 0 400~1500 50 5 400~1500 25 7.5 400~1500 25 10 700~1500 25 12.5 700~1500 25 15 1000~1500 25 17.5 1000~1500 25 Error analysis In this experiment, the force and torque was seven times repeated collection. As for multi-point measurement, each measuring point has the same repetitions and has the same accuracy. The formula for the uncertainly of multipoint measuring is shown in formula 4.1[12] [13]: i= 1 j= 1 a ) σ = k( n 1) (4.1) The random uncertainty of the measurement is shown in formula 4.2: k = tα σ n ( a ij (4.2) {i} is the number of measuring points; {n} is number of measurement of each measuring point; {k} is total number of points; {t α }is confidence interval, determined by measuring frequency and confidence probability. The repetitions is 7, k=1, n=7, confidence probability is 0.95. t α = 2.447. The uncertainty of each u(m)and u(t)can be calculated. Error transfer formula is shown in 4.3: η = T (η) (T) 2 + n s (η) (n s ) 2 + V 0 (η) (V 0 ) 2 + M (η) (M) 2 (4.3) In this experiment, the flow velocity error and rotate speed error is under 0.5%. The efficiency error distribution of each measuring point is shown in figure 3: i 2 Field Code Changed

Figure. 3 propeller efficiency error distribution Because the measurement of the force and torque has a fixed deviation, when the wind speed and rotate speed are low, the measurement precision is low. So the speed of measurement point is improved to improve the measurement accuracy. The higher rotate speed means better measurement accuracy. The maximum error is under 5%, and when it related to the low advance ratio region the maximum error is under 3%. The experiment is in a credible range error. Results analysis Reynolds number can be determined by control the rotating speed of propeller and the speed of wind tunnel. After measured the aerodynamic force of SRP, front propeller and rear propeller, the dimensionless aerodynamic parameters could be determined. By definition, these parameter is as follows: (1)thrust coefficient of the propeller The t is the pull. (2)power of the propeller t Ct = (1) ρn D C p 2 4 s P = (2) ρn D 3 5 s Power coefficient is power coefficient, p is the power. (3)efficiency of the propeller η tv C 0 t = = λ (3) P CP With the advanced ratio is determined from 0.6-1.0, the thrust coefficient could be raised by improve the wind speed of wind tunnel as it shown in figure 4.

Figure. 4 Thrust coefficient with different wind speed In general, as the Reynolds number increases, the thrust coefficient is improving. As the installation angle of propeller is fixed, the attack angle of the blade is determined by installation angle and advanced ratio. With the same advanced ratio, improve the wind speed, screw speed increase too. As it shown in figure 5, the efficiency could be increased by improving the Reynolds number. When Reynolds number is large, the efficiency curve is very near. The propeller s maximum efficiency is 72% when the advanced ratio is 0.8-1.0 and wind speed is 15m/s. Chart. 2 the propeller efficiency Wind speed/re λ:0.8 0.88 0.91 5(32000) 40.6% 42.4% 31.3% 7.5(48000) 61.8% 63.0% 55.7% 10(64000) 61.8% 64.3% 61.6% 12.5(80000) 71.3% 64.6% 62.7% 15(96000) 72.4% 72.6% 70.0%

Figure. 5 η with different wind speed The efficiency of the rear propeller is significantly higher than SRP. At the same condition, the efficiency of the front propeller is lower than SRP. As the advanced ratio is 0.5-1.1, the CRP could improve the efficiency by 4%-6% in contrast with the SRP as it shown in figure 6. Figure. 6 η with different wind speed

Figure. 7 Ct with different wind speed In spite of the front propeller have the lowest thrust coefficient, the CRP has a higher thrust coefficient than SRP. The results indicate that the rear propeller have the highest thrust coefficient as it shown in figure 7. Summary In contrast with SRP, the wind test show that CRP for stratospheric ship could improve the efficiency by 4%-7%. This result could be used to guide the design of stratospheric airship propulsion system. References [1] Xu Cao. Summary of the ISIS stratosphere airship. Beijing: China Academic Journal Electronic Publishing House [2] NIE wansheng., LUO shibin. Analisis of key technologies and development trend of near space vehicle. Journal of National University of Defense Technology. Vol.34 No.2 Apr.2012. [3] Bryan D. McGranahan and Michael S. Selig. Surface Oil Flow Measure- ments on Several Airfoils at Low Reynolds Numbers. 21st AIAA Applied AerodynamicsConference June 23 26, 2003/Orlando, FL, AIAA 2003-4067[4] R.J. Ong, J.T. Dawley and P.G. Clem: submitted to Journal of Materials Research (2003) [4] Jewel B Bar low,willian H Rae Jr, Alan Pope. Low-Speed Wind T unnel testing. New York: Awiley- Inte rscience Publicatuion, 1991 [5] S. Saito, H. Kobayashi. Performance Calculation of Counter Rotation Propeller. AIAA-87-1889 [6] Lock, C. N. H., "Interference Velocity for a Close Pair of Contra-Rotating Airscrews, A & M 2084, July 1941. [7] Biermann, D. and Gray, W. H., "Wind Tunnel Tests of Singleand Dual-Rotating Pusher Propellers Having from 3 to 8 Blades,"NACA ARR (WR L-359), February 1942. [8] Biermann, D. and Hartman, E. P., "Wind Tunnel Tests of Fourand Six Blade Single and Dual-Rotating Tractor Propellers," NACARept. 747, 1942.

[9] McHugh, J. G. and Pepper, E., "The Characteristics of TwoModel 6-Blade Counterrotating Pusher Propellers of Conventionaland Improved Aerodynamic Design," NACA ARR (WR L-404), June1942. [10] LIU Pei-qing, MA Rong, Ground wind tunnel test study of propeller of stratospheric airships, Journal of Aerospace Power. Vol.26 No.8 Aug. 2011 [11] Ronrbach, C. Meizger, F. B. Black, D. M. and Ladden, R. M. Evaluation of wind tunnel bladed propeller at Mach Numbers From 0.45 to 0.85, NASA CR 3505 [12] Facek Mieloszyk, Cezary Galinski and Fanusz Piechna, Countra-rotating propeller for fixed wing MAV:Part 1, Aircraft Engineering and Aerospace Technology, ISSN 1748-8842 [13] Facek Mieloszyk, Cezary Galinski and Fanusz Piechna, Countra-rotating propeller for fixed wing MAV:Part 2, Aircraft Engineering and Aerospace Technology, ISSN 1748-8842 [14] LIU Pei-qing, Air propeller theory and its application. IBSN 7-81077-765-3