Current/voltage-mode third order quadrature oscillator employing two multiple outputs CCIIs and grounded capacitors

Similar documents
Oscillator. Introduction of Oscillator Linear Oscillator. Stability. Wien Bridge Oscillator RC Phase-Shift Oscillator LC Oscillator

A Novel Isolated Buck-Boost Converter

ECEN620: Network Theory Broadband Circuit Design Fall 2012

Linearization of the Output of a Wheatstone Bridge for Single Active Sensor. Madhu Mohan N., Geetha T., Sankaran P. and Jagadeesh Kumar V.

Revision: August 19, E Main Suite D Pullman, WA (509) Voice and Fax

ECE 2100 Circuit Analysis

Section I5: Feedback in Operational Amplifiers

ECEN620: Network Theory Broadband Circuit Design Fall 2014

Bicycle Generator Dump Load Control Circuit: An Op Amp Comparator with Hysteresis

1. Transformer A transformer is used to obtain the approximate output voltage of the power supply. The output of the transformer is still AC.

Micro and Smart Systems

Design and Simulation of Dc-Dc Voltage Converters Using Matlab/Simulink

Sections 15.1 to 15.12, 16.1 and 16.2 of the textbook (Robbins-Miller) cover the materials required for this topic.

JAZAN University. Department: Electrical Engineering. Names & ID: Electronics LAB - 1/ / Electronics LAB - EngE : 314 G:...

Series and Parallel Resonances

Determining the Accuracy of Modal Parameter Estimation Methods

Least Squares Optimal Filtering with Multirate Observations

BASIC DIRECT-CURRENT MEASUREMENTS

Synchronous Motor V-Curves

ZVS Boost Converter. (a) (b) Fig 6.29 (a) Quasi-resonant boost converter with M-type switch. (b) Equivalent circuit.

A Comparative Study on Predictive and ISVM Direct Torque Control Methods for a Doubly Fed Induction Machine Fed by an Indirect Matrix Converter

Relationships Between Frequency, Capacitance, Inductance and Reactance.

Copyright Paul Tobin 63

Modeling the Nonlinear Rheological Behavior of Materials with a Hyper-Exponential Type Function

Lab 11 LRC Circuits, Damped Forced Harmonic Motion

Lecture 02 CSE 40547/60547 Computing at the Nanoscale

A Comparison of AC/DC Piezoelectric Transformer Converters with Current Doubler and Voltage Doubler Rectifiers

A Novel Electro-thermal Simulation Approach to Power IGBT Modules for Automotive Traction Applications

ECEN 4872/5827 Lecture Notes

1.1 The main transmission network of Eskom The classical two generator model 11

Physics 102. Second Midterm Examination. Summer Term ( ) (Fundamental constants) (Coulomb constant)

Module 4: General Formulation of Electric Circuit Theory

OTHER USES OF THE ICRH COUPL ING CO IL. November 1975

2. Find i, v, and the power dissipated in the 6-Ω resistor in the following figure.

ECE 2100 Circuit Analysis

Supplementary Course Notes Adding and Subtracting AC Voltages and Currents

Edexcel GCSE Physics

OP AMP CHARACTERISTICS

THERMAL-VACUUM VERSUS THERMAL- ATMOSPHERIC TESTS OF ELECTRONIC ASSEMBLIES

Transduction Based on Changes in the Energy Stored in an Electrical Field

Chapter 16. Capacitance. Capacitance, cont. Parallel-Plate Capacitor, Example 1/20/2011. Electric Energy and Capacitance

General Amplifiers. Analog Electronics Circuits Nagamani A N. Lecturer, PESIT, Bangalore 85. Cascade connection - FET & BJT

The Study of a Dual-Mode Ring Oscillator

Finding the Minimum Input Impedance of a Second-Order Unity-Gain Sallen-Key Low-Pass Filter without Calculus

ENG2410 Digital Design Sequential Circuits: Part B

Description Absolute Maximum Ratings Parameter Max. Units Thermal Resistance Parameter Typ. Max. Units

Application Of Mealy Machine And Recurrence Relations In Cryptography

Generation of Four Phase Oscillators Using Op Amps or Current Conveyors

A Self-Sensing Homopolar Magnetic Bearing: Analysis and Experimental Results

Reactive Power Control of Isolated Wind-Diesel Hybrid Power Systems for Variable Slip

Applying Kirchoff s law on the primary circuit. V = - e1 V+ e1 = 0 V.D. e.m.f. From the secondary circuit e2 = v2. K e. Equivalent circuit :

A Few Basic Facts About Isothermal Mass Transfer in a Binary Mixture

^YawataR&D Laboratory, Nippon Steel Corporation, Tobata, Kitakyushu, Japan

Supplementary Course Notes Adding and Subtracting AC Voltages and Currents

T(s) 1+ T(s) 2. Phase Margin Test for T(s) a. Unconditionally Stable φ m = 90 o for 1 pole T(s) b. Conditionally Stable Case 1.

EXPERIMENTAL STUDY ON DISCHARGE COEFFICIENT OF OUTFLOW OPENING FOR PREDICTING CROSS-VENTILATION FLOW RATE

A Non-Insulated Resonant Boost Converter

MODULE TITLE : OPERATIONAL AMPLIFIERS TOPIC TITLE : FILTERS LESSON 1 : FILTERS

Numerical Simulation of the Thermal Resposne Test Within the Comsol Multiphysics Environment

Introduction to Smith Charts

initially lcated away frm the data set never win the cmpetitin, resulting in a nnptimal nal cdebk, [2] [3] [4] and [5]. Khnen's Self Organizing Featur

Robust Power Flow Control of Grid-tied Inverters Based on the Uncertainty and Disturbance Estimator

Methods for Determination of Mean Speckle Size in Simulated Speckle Pattern

Protection of ungrounded systems using an advanced relay element

Enhancing Performance of MLP/RBF Neural Classifiers via an Multivariate Data Distribution Scheme

1996 Engineering Systems Design and Analysis Conference, Montpellier, France, July 1-4, 1996, Vol. 7, pp

Verification of Quality Parameters of a Solar Panel and Modification in Formulae of its Series Resistance

CHAPTER 3 INEQUALITIES. Copyright -The Institute of Chartered Accountants of India

POWER AMPLIFIERS. 1. Explain what are classes A, B, AB and C amplifiers in terms of DC biasing using a MOSFET drain characteristic.

Engineering Approach to Modelling Metal THz Structures

TOPPER SAMPLE PAPER 2 Class XII- Physics

Plan o o. I(t) Divide problem into sub-problems Modify schematic and coordinate system (if needed) Write general equations

Schedule. ECEN 301 Discussion #17 Operational Amplifiers 1. Date Day Class No. Lab Due date. Exam

C Soldering Temperature, for 10 seconds 300 (1.6mm from case )

NUROP CONGRESS PAPER CHINESE PINYIN TO CHINESE CHARACTER CONVERSION

Description Absolute Maximum Ratings Parameter Max. Units Thermal Resistance Parameter Typ. Max. Units

A Study on Pullout Strength of Cast-in-place Anchor bolt in Concrete under High Temperature

An Equivalent pi Network Model for Power System State Estimation with Network Parameter Errors

Data Sheet. ACPL-8x7 Multi-Channel Full-Pitch Phototransistor Optocoupler. Description. Features. ACPL-827 pin layout.

Optical property of Few-Mode Fiber with Non-uniform Refractive Index for Cylindrical Vector Beam Generation

MODULE TITLE : ELECTRONICS TOPIC TITLE : AMPLIFIERS LESSON 1 : FEEDBACK

Multi Level Reinjection ac/dc Converters for HVDC

Curvature Effects on Thermal Buckling Load of DWCNT Under Axial Compression Force

A Scalable Recurrent Neural Network Framework for Model-free

Phase Noise in LC Oscillators: From Basic Concepts to Advanced Topologies. Carlo Samori. Politecnico di Milano Milano, Italy

Performance Bounds for Detect and Avoid Signal Sensing

General Chemistry II, Unit I: Study Guide (part I)

Differentiation Applications 1: Related Rates

Three charges, all with a charge of 10 C are situated as shown (each grid line is separated by 1 meter).

Figure 1a. A planar mechanism.

4) What is the magnitude of the net electric field at the center of the square?

CBSE Board Class XII Physics Set 1 Board Paper 2008 (Solution)

Laboratory #2: Introduction to Microstripline Transmission Lines, Reflection and Transmission Coefficients, and S-Parameters

GENERAL FORMULAS FOR FLAT-TOPPED WAVEFORMS. J.e. Sprott. Plasma Studies. University of Wisconsin

A mathematical model for complete stress-strain curve prediction of permeable concrete

ECE 497 JS Lecture - 14 Projects: FDTD & LVDS

Q1. A) 48 m/s B) 17 m/s C) 22 m/s D) 66 m/s E) 53 m/s. Ans: = 84.0 Q2.

Supporting information

Phys102 Second Major-102 Zero Version Coordinator: Al-Shukri Thursday, May 05, 2011 Page: 1

Chem 163 Section: Team Number: ALE 24. Voltaic Cells and Standard Cell Potentials. (Reference: 21.2 and 21.3 Silberberg 5 th edition)

Transcription:

Indian Jurnal f Pure & Applied Physics Vl. 49 July 20 pp. 494-498 Current/vltage-mde third rder quadrature scillatr emplying tw multiple utputs CCIIs and grunded capacitrs Jiun-Wei Hrng Department f Electrnic Engineering Chung Yuan Christian University Chung-Li 32023 Taiwan E-mail: jwhrng@cycu.edu.tw Received 4 Nvember 200; revised 26 April 20; accepted 3 May 20 A new quadrature scillatr circuit using tw multiple utputs secnd-generatin current cnveyrs (CCIIs) three grunded capacitrs and three resistrs is presented. Tw high utput impedance current-mde signals and tw vltagemde signals each pair with 90 phase difference are available in the prpsed circuit. The scillatin cnditin and scillatin frequency are independently cntrllable thrugh grunded resistrs. The use f nly grunded capacitrs makes the prpsed circuit attractive fr integrated circuit implementatin. Keywrds: Quadrature scillatr Current cnveyrs Current-mde Vltage-mde Intrductin A quadrature scillatr is used because the circuit prvides tw sinusids with 90 phase difference as fr example in telecmmunicatins fr quadrature mixers and single-sideband generatrs r fr measurement purpses in vectr generatrs r selective vltmeters. Therefre quadrature scillatrs cnstitute an imprtant unit in many cmmunicatin and instrumentatin systems. The quadrature scillatrs -8 generate vltage-mde signals. Several current-mde sinusidal scillatrs were prpsed in the literature. Hwever the current-mde high utput impedance sinusidal scillatrs 9- d nt prvide anther high utput impedance quadrature current utput. Mrever the current-mde quadrature scillatrs 2-3 require additinal current fllwers fr sensing and taking ut the quadrature utputs therein and the use f these additinal current fllwers with the virtual grunded inputs may result in flating capacitrs realizatin fr what is riginally described as grunded capacitrs realizatin. Hrng 4 prpsed a current-mde high utput impedance quadrature scillatr using tw differential vltage current cnveyrs tw resistrs and tw capacitrs. Hwever the scillatin cnditin and scillatin frequency cannt be independently tuned. Because the high-rder netwrk has high accuracy and high quality factr it gives gd frequency respnse with lw distrtin 56. Maheshwari and Khan 6 prpsed a third rder quadrature scillatr that generates bth vltage-mde and current-mde quadrature signals in the same circuit cnfiguratin by using fur current cntrlled current cnveyrs and three capacitrs 6. In this paper a new third rder quadrature scillatr circuit using tw multiple utputs secndgeneratin current cnveyrs (CCIIs) three grunded capacitrs and three resistrs is presented. Tw high utput impedance sinusid current-mde signals and tw vltage-mde signals each pair with 90 phase difference are available in the prpsed circuit. The scillatin cnditin and scillatin frequency are independently cntrllable thrugh grunded resistrs. The use f nly grunded capacitrs makes the prpsed circuit attractive fr integrated circuit implementatin 7. The prpsed circuit emplys less active cmpnents with respect t the previus quadrature scillatr 6. 2 Circuit Descriptin The circuit symbl f the multiple utputs CCII is shwn in Fig. which shws tw types f utput terminals the psitive utputs represented by terminal z+ and the negative by terminal z-. The terminal characteristic f the multiple utputs CCII can be described by the fllwing matrix equatin: iy 0 0 0... 0 0... 0 vy v 0 0... 0 0... 0 x i x i 0 0... 0 0... 0v z + z+........................... =... i 0 0... 0 0... 0v zm+ zm+ i 0 0... 0 0... 0 z vz.............................. i 0 0... 0 0... 0 zn vzn ()

HORNG: CURRENT/VOLTAGE-MODE THIRD ORDER QUADRATURE OSCILLATOR 495 Fig. Multiple utputs CCII circuit symbl The prpsed quadrature scillatr is shwn in Fig. 2. The characteristic equatin f the circuit can be expressed as: s 3 C C 2 C 3 R R 2 R 3 + s 2 (C + C 2 )C 3 R R 3 + sc 3 R 3 + = 0 (2) The scillatin cnditin and scillatin frequency can be btained as: Fig. 2 Prpsed CCIIs based quadrature scillatr The phase difference φ between V 2 and V is: φ = 90 (6) ensuring the vltages V 2 and V t be in quadrature. Frm Fig. 2 the current transfer functin frm I 2 t I is: CC 2R2 R3 = ( C + C ) C 2 3 (3) I2 ( s) = (7) I ( s) sc R 3 3 ω = (4) C C R R 2 2 The scillatin frequency can be adjusted by the grunded resistr R. The scillatin cnditin can be independently adjusted by the grunded resistr R 3. Fig. 2 emplys nly grunded capacitrs. The use f grunded capacitrs is particularly attractive fr integrated circuit implementatin 7. The passive sensitivities f this sinusidal scillatr are all lw and btained as: S ω C C2 R2 R = 3 2 Frm Fig. 2 the vltage transfer functin frm V 2 t V is : V 2 ( s) = (5) V ( s) sc R 3 The phase difference φ between I 2 and I is: φ = 90 (8) ensuring the currents I 2 and I t be in quadrature. Thus the prpsed circuit cnfiguratin can prvide bth vltage-mde and current-mde quadrature signals simultaneusly. Because the utput impedances f the currents I r I 2 are very high the tw utput terminals I and I 2 can be directly cnnected t the next stage respectively. The resistrs R and R 3 are cnnected t the tw x terminals f the CCII() and CCII(2) respectively. This design ffers anther feature f a direct incrpratin f the parasitic resistance (R x ) as a part f the main resistance. Frm Eqs (5) and (7) the magnitudes f V 2 and V r I 2 and I need nt be the same. Fr the applicatins needing equal magnitude quadrature utputs ther amplifying circuits are needed.

496 INDIAN J PURE & APPL PHYS VOL 49 JULY 20 3 Effect f the CCII Parasitic Elements n the Prpsed Circuits A nn-ideal multiple utputs CCII mdel 89 is shwn in Fig. 3. It is shwn that the real multiple utputs CCII have parasitic resistrs and capacitrs frm the y and z terminals t the grund and als a series resistr at the input terminal x. The values f the parasitic impedances 9 are R x = 60Ω R y = 7 MΩ R z = R z2 = 3 MΩ C y = 8 pf C z = C z2 = 4 pf. The α k (s) (k = 2) and β(s) represent the frequency transfers f the internal current and vltage fllwers f the multiple utputs CCII respectively. They can be apprximated by first rder lw pass functins which can be cnsidered t have a near unity value fr frequencies much less than their crner frequencies 89. Taking int accunt the nn-ideal multiple utputs CCII mdel f Fig. 3 in Fig. 2 and assuming the circuit is wrking at frequencies much less than the crner frequencies f α k (s) and β(s) namely α k (s) = α k = ε k and ε k ( ε k <<) dentes the current tracking errr and β(s)=β= ε 2 and ε 2 ( ε 2 <<) dentes the vltage tracking errr f the multiple utputs CCII. The characteristic equatin f Fig. 2 becmes: s C ' C ' C ' R ' R R ' R R R + s R ' R '[ C ' C ' R R R 3 2 2 3 2 3 4 5 y 3 2 2 4 y + C ' C ' R R ( R + R ) + C ' C '( R + R ) R R ] 3 4 5 2 y 2 3 2 4 5 y + sr '[ C ' R ' R ( R + R ) + C ' R '( R + R ) R 3 4 2 y 2 2 4 y + C ' R ( R ' R + R ' R + R ' R + R R α β )] 3 5 2 4 y 4 y + R '( R + R ) R ' + R ' R ' R + R ' R R α β 2 4 3 3 y 3 4 y + R4R5 R y α2α2ββ 2 = 0 (9) where C ' = C + Cz + Cz2 C2 ' = C2 + Cy C3 ' = C3 + Cz2 + Cy2 R ' = R + Rx R3 ' = R3 + Rx2 R4 = Rz / / Rz 2 R = R / / R. 5 z2 y2 The mdified scillatin cnditin and scillatin frequency are: R '( R + R ) R ' + R ' R ' R + R ' R R α β 2 4 3 3 y 3 4 y + R R R α α β β 4 5 y 2 2 2 R ' R '[ C ' C ' R R R + C ' C ' R R ( R + R ) 3 2 2 4 y 3 4 5 2 y + C ' C '( R + R ) R R ] 2 3 2 4 5 y C ' R ' R ( R + R ) + C ' R '( R + R ) R 4 2 y 2 2 4 y + C3 ' R5 ( R ' R2 + R ' R4 + R ' Ry + R4Ryαβ ) = (0) C ' C ' C ' R ' R R R R ω = 2 3 2 4 5 y C ' R ' R ( R + R ) + C ' R '( R + R ) R 4 2 y 2 2 4 y + C ' R ( R ' R + R ' R + R ' R + R R α β ) 3 5 2 4 y 4 y C ' C ' C ' R ' R R R R 2 3 2 4 5 y () Eqs (0) and () are cupled due t the parasitic impedances especially because R 4 R 5 and R y are finite. This fact implies that the adjustment f the scillatin frequency affects the scillatin cnditin [R appears in bth Eqs (0) and ()]. Nevertheless the scillatin cnditin can be tuned by varying R 3 after adjusting the scillatin frequency by means f R. 4 Simulatin Results PSPICE simulatins were carried ut t demnstrate the feasibility f the prpsed circuit in Fig. 2 using 0.8 µm level 3 MOSFET frm TSMC. The multiple utputs CCII was realized by the CMOS implementatin 20 in Fig. 4. The aspect ratis f the MOS transistrs are shwn in Table. The multiple current utputs can be easily implemented by simply adding utput branches. Fig. 3 Nn-ideal multiple utputs CCII mdel Fig. 4 Implementatin f multiple utputs CCII

HORNG: CURRENT/VOLTAGE-MODE THIRD ORDER QUADRATURE OSCILLATOR 497 Table Aspect ratis f the MOS in Fig. 4. MOS transistr W/L MM2 36/0.9 M3 63/0.9 M4M5 54/0.9 M6 72/0.9 M7~M6 8/0.9 Table 2 Ttal harmnic distrtin analysis f V in Fig. 2 Harmnic number Frequency (Hz) Furier Nrmalized cmpnent cmpnent Nrmalized 2.0E+05 3.88E-0.000E+00 8.995E+0 0.000E+00 2 4.220E+05 4.598E-03.85E-02.065E+02 2.864E+02 3 6.330E+05 7.949E-03 2.048E-02 4.279E+0 3.26E+02 4 8.440E+05 7.82E-04 2.05E-03 8.872E+0 4.485E+02 5.055E+06 9.002E-04 2.39E-03.374E+02 3.24E+02 6.266E+06 6.577E-04.695E-03.57E+02 6.554E+02 7.477E+06 3.690E-04 9.506E-04 6.454E+0 6.942E+02 8.688E+06 7.489E-05.930E-04 2.88E+0 7.484E+02 9.899E+06.954E-04 5.033E-04 6.52E+0 8.747E+02 DC cmpnent: 7.80769E-03 Ttal harmnic distrtin: 2.39499E+00 PERCENT Table 3 Ttal harmnic distrtin analysis f I in Fig. 2 Harmnic number Frequency (Hz) Furier Nrmalized cmpnent cmpnent Nrmalized 2.0E+05 3.852E-0.000E+00.32E+02 0.000E+00 2 4.220E+05 7.852E-03 2.038E-02 4.06E+0 3.048E+02 3 6.330E+05 6.374E-03.655E-02 6.079E+0 3.355E+02 4 8.440E+05 2.739E-03 7.0E-03.40E+0 5.398E+02 5.055E+06 3.24E-03 8.E-03.854E+0 6.79E+02 6.266E+06.867E-03 4.847E-03 7.782E+0 7.849E+02 7.477E+06.45E-03 3.767E-03.720E+0 9.076E+03 8.688E+06.43E-03 3.74E-03.093E+0.046E+03 9.899E+06.429E-03 3.7E-03.647E+0.73E+03 DC cmpnent: 6.05884E-03 Ttal harmnic distrtin: 2.9548E+00 PERCENT Fig. 5 (a) Simulated utput wavefrms f vltage-mde signals in Fig. 2; (b) Simulated utput wavefrms f current-mde signals in Fig. 2. Fig. 6 Simulatin results f the scillatin frequency f Fig. 2 which is btained by varying the value f the resistr R Figure 5(a and b) shws the vltage-mde and current-mde quadrature sinusidal utput wavefrms f Fig. 2 respectively with C = C 2 = C 3 = 80 pf R = 6 kω R 2 = 5 kω R 3 = 6 kω and the pwer supply ±.25V V b = 0.65V. The results f the V and I ttal harmnic distrtin analysis are presented in Tables 2 and 3 respectively. Fig. 6 shws the simulatin results f the scillatin frequency f Fig. 2 by varying the value f the resistr R with C = C 2 = C 3 = 80 pf R 2 = 5 k Ω and R 3 =6 k Ω. 5 Cnclusins A new quadrature scillatr using tw multiple utputs CCIIs three resistrs and three grunded capacitrs is presented. This quadrature scillatr prvides the fllwing advantages: (i) tw vltagemde and tw current-mde sinusidal utput signals each pair with 90 phase difference are btained simultaneusly; (ii) the utput impedances f the current-mde signals are very high; (iii) the scillatin cnditin and scillatin frequency are independently cntrllable thrugh grunded resistrs; (iv) the use f nly grunded capacitrs; (v) a direct incrpratin f the parasitic resistances at the x terminals f the CCIIs (R x ) as a part f the main resistances. The prpsed circuit emplys less active cmpnents with respect t the previus quadrature scillatr 6. References Hlzel R IEEE Transactins n Instrumentatin and Measurement 42 (993) 758. 2 Ahmed M T Khan I A & Minhaj N Internatinal J Electrnics 83 (997) 20.

498 INDIAN J PURE & APPL PHYS VOL 49 JULY 20 3 Sliman A M J Franklin Institute 336 (999) 735. 4 Khan I A & Khwaja S Internatinal J Electrnics 87 (2000) 353. 5 Tangsrirat W Prasertsm D Piyatat T & Surakampntrn W Internatinal J Electrnics 95 (2008) 9. 6 Tangsrirat W Indian J Pure & Appl Phys 47 (2009) 85. 7 Hrng J W Cmputers and Electrical Engineering 3 (2005) 8. 8 Hrng J W Hu C L Chang C M Chung W Y Tang H W & Wen Y H Internatinal J Electrnics 92 (2005) 2. 9 Abuelma atti M T & Al-Zaher H A IEEE Transactins n Circuits and Systems-II: Analg and Digital Signal Prcessing 46 (999) 69. 0 Gupta S S & Senani R Electrnics Lett 36 (2000) 95. Cam U Tker A Cicekglu O & Kuntman H Analg Integrated Circuits and Signal Prcessing 24 (2000) 23. 2 Abuelma atti M T IEEE Transactins n Circuits and Systems-I: Fundamental Thery and Applicatins 39 (992) 08. 3 Abuelma atti M T & Al-Zaher H A Internatinal J Electrnics 85 (998) 77. 4 Hrng J W IEICE Transactins n Fundamentals f Electrnics Cmmunicatins and Cmputer Sciences E86- A (2003) 252. 5 Prmmee P & Dejhan K Internatinal J Electrnics 89 (2002) 365. 6 Maheshwari S & Khan I A IEE Prceedings Circuits Devices and Systems 52 (2005) 605. 7 Bhushan M & Newcmb R W Electrnic Lett 3 (967) 48. 8 Fabre A Saaid O & Barthelemy H Analg Integrated Circuits and Signal Prcessing 7 (995) 3. 9 Martinez P A Sabadell J Aldea C & Celma S IEEE Transactins n Circuits and Systems-I: Fundamental Thery and Applicatins 46 (999) 386. 20 Surakampntrn W Riewruja V Kumwachara K & Dejhan K IEEE Transactins n Instrument and Measur 40 (99) 699.