TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC4013BP,TC4013BF,TC4013BFN TC4013B Dual D-Type Flip Flop TC4013B contains two independent circuits of D type flip-flop. The input level applied to DATA input are transferred to Q and Q output by rising edge of the clock pulse. When SET input is placed at H, and RESET input is placed at L, outputs become Q = H, and Q = L. When RESET input is placed at H, and SET input is placed at L, outputs become Q = L, and Q = H. When both of RESET input and SET input are at H, outputs become Q = H and Q = H. Pin Assignment Note: xxxfn (JEDEC SOP) is not available in Japan. TC4013BP TC4013BF Block Diagram TC4013BFN Weight DIP14-P-300-2.4 SOP14-P-300-1.27A SOP14-P-300-1.27 SOL14-P--1.27 : 0.96 g (typ.) : 0.18 g (typ.) : 0.18 g (typ.) : 0.12 g (typ.) 1
Truth Table Inputs Outputs RESET SET DATA CK Qn + 1 Q n + 1 L H * * H L H L * * L H H H * * H H L L L L H L L H H L L L * Qn Qn *: Don t care : Level change : No change Logic Diagram Absolute Maximum Ratings (Note) Characteristics Symbol Rating Unit DC supply voltage V DD V SS 0.~V SS + 20 V Input voltage V IN V SS 0.~V DD + 0. V Output voltage V OUT V SS 0.~V DD + 0. V DC input current I IN ± ma Power dissipation P D 300 (DIP)/180 (SOIC) mw Operating temperature range T opr 40~8 C Storage temperature range T stg 6~ C Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. 2
Recommended Operating Conditions (V SS = 0 V) (Note) Characteristics Symbol Test Condition Min Typ. Max Unit DC supply voltage V DD 3 18 V Input voltage V IN 0 V DD V Note: The recommended operating conditions are required to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. Static Electrical Characteristics (V SS = 0 V) Characteristics High-level output voltage Low-level output voltage Output high current Symbol V OH I OUT < 1 µa V IN = V SS, V DD V OL I OUT < 1 µa V IN = V SS, V DD I OH V OH = 4.6 V V OH = 2. V V OH = 9. V V OH = 13. V Test Condition 40 C 2 C 8 C V IN = V SS, V DD V DD (V) 1 1 1 Min Max Min Typ. Max Min Max 4.9 9.9 14.9 0.61 2.0 1.0 4.00 0.0 0.0 0.0 4.9 9.9 14.9 0.1 2. 1.30 3.40.00.00 1.00 0.00 0.00 0.00 1.0 4.0 2.2 9.0 0.0 0.0 0.0 4.9 9.9 14.9 0.42 1.70 1. 2.80 0.0 0.0 0.0 Unit V V ma V OL = 0.4 V 0.61 0.1 1.2 0.42 Output low current I OL V OL = 0. V V OL = 1. V 1 1.0 4.00 1.30 3.40 3.2 12.0 1. 2.80 ma V IN = V SS, V DD V OUT = 0. V, 4. V 3. 3. 2.7 3.0 Input high voltage V IH V OUT = 1.0 V, 9.0 V V OUT = 1. V, 13. V 1 7.0 11.0 7.0 11.0.0 8.2 7.00 11.00 V I OUT < 1 µa Input low voltage Input current Quiescent supply current V IL V OUT = 0. V, 4. V V OUT = 1.0 V, 9.0 V V OUT = 1. V, 13. V I OUT < 1 µa 1 1. 3.0 4.0 2.2 4.0 6.7 H level I IH V IH = 18 V 18 0.1 0.1 1.0 L level I IL V IL = 0 V 18 0.1 0.1 1.0 I DD V IN = V SS, V DD (Note) 1 1 2 4 0.002 0.004 0.008 1. 3.0 4.0 1 2 4 1. 3.0 4.0 30 60 120 V µa µa Note: All valid input combinations. 3
Dynamic Electrical Characteristics (Ta = 2 C, V SS = 0 V, C L = 0 pf) TC4013BP/BF/BFN Characteristics Symbol Test Condition V DD (V) Min Typ. Max Unit 70 200 Output transition time t TLH 3 0 (low to high) ns 1 30 80 70 200 Output transition time (high to low) t THL 3 0 ns 1 30 80 Propagation delay time t plh 130 300 (CK-Q, Q ) t phl 6 130 ns 1 0 90 1 300 Propagation delay time t plh 0 130 (SET, RESET-Q, Q ) ns 1 40 90 Propagation delay time 1 300 t phl 0 130 ns (SET, RESET-Q, Q) 1 40 90 Max clock frequency f CL 3. 8.0 8 16 MHz 1 12.0 20 Max clock input rise time Max clock input fall time t rcl t fcl No limit µs 1 Min pulse width (SET, RESET) t W 60 30 180 80 ns 1 2 0 Min clock pulse width t W 60 30 140 60 ns 1 2 40 Min set-up time (DATA-CK) t su 40 20 ns 1 1 Min hold time (DATA-CK) t H 1 20 6 40 20 1 ns 40 Min removal time t rem 20 (SET, RESET-CK) ns 1 1 Input capacitance C IN 7. pf 4
Waveform for Measurement of Dynamic Characteristics Waveform 1 Waveform 2
Package Dimensions Weight: 0.96 g (typ.) 6
Package Dimensions Weight: 0.18 g (typ.) 7
Package Dimensions Weight: 0.18 g (typ.) 8
Package Dimensions (Note) Weight: 0.12 g (typ.) Note: This package is not available in Japan. 9
Note: Lead (Pb)-Free Packages DIP14-P-300-2.4 SOP14-P-300-1.27A SOL14-P--1.27 RESTRICTIONS ON PRODUCT USE 060116EBA The information contained herein is subject to change without notice. 0223_D TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the Handling Guide for Semiconductor Devices, or TOSHIBA Semiconductor Reliability Handbook etc. 0223_A The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ( Unintended Usage ). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer s own risk. 0223_B The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. 0606_Q The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. 0223_C The products described in this document are subject to the foreign exchange and foreign trade laws. 0223_E