Analysis (a) Process 1-2: isentropic compression. p = 755K. R7] h87kpa.m 3/kg.K }30~ = O.906m 3/kg = V max

Similar documents
Assumptions 1 Steady operating conditions exist. 2 Kinetic and potential energy changes are negligible. hl = IOkPa = 191.

9.1 Basic considerations in power cycle analysis. Thermal efficiency of a power cycle : th = Wnet/Qin

Teaching schedule *15 18

The First Law of Thermodynamics. By: Yidnekachew Messele

Dr Ali Jawarneh. Hashemite University

MAE 11. Homework 8: Solutions 11/30/2018

Lecture 43: Aircraft Propulsion

MAHALAKSHMI ENGINEERING COLLEGE

Lecture 44: Review Thermodynamics I

SPC 407 Sheet 5 - Solution Compressible Flow Rayleigh Flow

CHAPTER 5 MASS AND ENERGY ANALYSIS OF CONTROL VOLUMES

Thermodynamic Cycles

Thermodynamics is the Science of Energy and Entropy

UNIT I Basic concepts and Work & Heat Transfer

1 st Law Analysis of Control Volume (open system) Chapter 6

ME 440 Aerospace Engineering Fundamentals

Chapter 5. Mass and Energy Analysis of Control Volumes

First Law of Thermodynamics

+ m B1 = 1. u A1. u B1. - m B1 = V A. /v A = , u B1 + V B. = 5.5 kg => = V tot. Table B.1.

I. (20%) Answer the following True (T) or False (F). If false, explain why for full credit.


1. (10) Calorically perfect ideal air at 300 K, 100 kpa, 1000 m/s, is brought to rest isentropically. Determine its final temperature.

c Dr. Md. Zahurul Haq (BUET) Thermodynamic Processes & Efficiency ME 6101 (2017) 2 / 25 T145 = Q + W cv + i h 2 = h (V2 1 V 2 2)

THERMODYNAMICS, FLUID AND PLANT PROCESSES. The tutorials are drawn from other subjects so the solutions are identified by the appropriate tutorial.

= 1 T 4 T 1 T 3 T 2. W net V max V min. = (k 1) ln ( v 2. v min

Delft University of Technology DEPARTMENT OF AEROSPACE ENGINEERING

Please welcome for any correction or misprint in the entire manuscript and your valuable suggestions kindly mail us


Week 4. Gas Power Cycles IV. GENESYS Laboratory

Where F1 is the force and dl1 is the infinitesimal displacement, but F1 = p1a1

Chapter 5. Mass and Energy Analysis of Control Volumes. by Asst. Prof. Dr.Woranee Paengjuntuek and Asst. Prof. Dr.Worarattana Pattaraprakorn

BME-A PREVIOUS YEAR QUESTIONS

I.C. Engine Cycles. Thermodynamic Analysis

THE FIRST LAW APPLIED TO STEADY FLOW PROCESSES

20... Figure 9.6 Thermal efficiency of the cold air standard Diesel cycle, k = 1.4.

Introduction to Thermodynamic Cycles Part 1 1 st Law of Thermodynamics and Gas Power Cycles

Lecture 40: Air standard cycle, internal combustion engines, Otto cycle

Chapter 5: The First Law of Thermodynamics: Closed Systems

To receive full credit all work must be clearly provided. Please use units in all answers.

ME Thermodynamics I

R13 SET - 1 '' ''' '' ' '''' Code No RT21033

Today lecture. 1. Entropy change in an isolated system 2. Exergy

Thermodynamics ENGR360-MEP112 LECTURE 7

T222 T194. c Dr. Md. Zahurul Haq (BUET) Gas Power Cycles ME 6101 (2017) 2 / 20 T225 T226

CHAPTER 7 ENTROPY. Copyright Hany A. Al-Ansary and S. I. Abdel-Khalik (2014) 1

Civil aeroengines for subsonic cruise have convergent nozzles (page 83):

Chapter 7. Entropy: A Measure of Disorder

Two mark questions and answers UNIT I BASIC CONCEPT AND FIRST LAW SVCET

5/6/ :41 PM. Chapter 6. Using Entropy. Dr. Mohammad Abuhaiba, PE

Lecture with Numerical Examples of Ramjet, Pulsejet and Scramjet

EVALUATION OF THE BEHAVIOUR OF STEAM EXPANDED IN A SET OF NOZZLES, IN A GIVEN TEMPERATURE

KNOWN: Pressure, temperature, and velocity of steam entering a 1.6-cm-diameter pipe.

ME 200 Final Exam December 12, :00 a.m. to 10:00 a.m.

Chapter 7. Entropy. by Asst.Prof. Dr.Woranee Paengjuntuek and Asst. Prof. Dr.Worarattana Pattaraprakorn

UBMCC11 - THERMODYNAMICS. B.E (Marine Engineering) B 16 BASIC CONCEPTS AND FIRST LAW PART- A

Department of Mechanical Engineering Indian Institute of Technology New Delhi II Semester MEL 140 ENGINEERING THERMODYNAMICS

Engineering Thermodynamics. Chapter 6. Entropy: a measure of Disorder 6.1 Introduction

ME 200 Thermodynamics 1 Fall 2016 Final Exam

Thermal Energy Final Exam Fall 2002

Unified Quiz: Thermodynamics

R13. II B. Tech I Semester Regular Examinations, Jan THERMODYNAMICS (Com. to ME, AE, AME) PART- A

SPC 407 Sheet 2 - Solution Compressible Flow - Governing Equations

3. Write a detailed note on the following thrust vector control methods:

SATHYABAMA UNIVERISTY. Unit III

Chapter 7. Dr Ali Jawarneh. Department of Mechanical Engineering Hashemite University

2-21. for gage pressure, the high and low pressures are expressed as. Noting that 1 psi = kpa,

ENT 254: Applied Thermodynamics

Course: MECH-341 Thermodynamics II Semester: Fall 2006

Section 4.1: Introduction to Jet Propulsion. MAE Propulsion Systems II

In the next lecture...

first law of ThermodyNamics

UNIT 1 COMPRESSIBLE FLOW FUNDAMENTALS

ESO201A: Thermodynamics

SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT

ME 300 Thermodynamics II Spring 2015 Exam 3. Son Jain Lucht 8:30AM 11:30AM 2:30PM

Chapter 1: 20, 23, 35, 41, 68, 71, 76, 77, 80, 85, 90, 101, 103 and 104.

Chapter 6. Using Entropy

ME Thermodynamics I. Lecture Notes and Example Problems

Name: I have observed the honor code and have neither given nor received aid on this exam.

Engineering Thermodynamics Solutions Manual

Week 8. Steady Flow Engineering Devices. GENESYS Laboratory

CHAPTER 8 THERMODYNAMICS. Common Data For Q. 3 and Q.4. Steam enters an adiabatic turbine operating at steady state with an enthalpy of 3251.

Readings for this homework assignment and upcoming lectures

Dishwasher. Heater. Homework Solutions ME Thermodynamics I Spring HW-1 (25 points)

Jet Aircraft Propulsion Prof. Bhaskar Roy Prof A M Pradeep Department of Aerospace Engineering Indian Institute of Technology, Bombay

Jet Aircraft Propulsion Prof. Bhaskar Roy Prof. A.M. Pradeep Department of Aerospace Engineering

Axial Flow and Radial Flow Gas Turbines

ES 202 Fluid and Thermal Systems

Unit Workbook 2 - Level 5 ENG U64 Thermofluids 2018 UniCourse Ltd. All Rights Reserved. Sample

Fuel, Air, and Combustion Thermodynamics

Chapter 17. For the most part, we have limited our consideration so COMPRESSIBLE FLOW. Objectives

c Dr. Md. Zahurul Haq (BUET) Entropy ME 203 (2017) 2 / 27 T037

Section A 01. (12 M) (s 2 s 3 ) = 313 s 2 = s 1, h 3 = h 4 (s 1 s 3 ) = kj/kgk. = kj/kgk. 313 (s 3 s 4f ) = ln

ME6301- ENGINEERING THERMODYNAMICS UNIT I BASIC CONCEPT AND FIRST LAW PART-A

Introduction to Engineering thermodynamics 2 nd Edition, Sonntag and Borgnakke. Solution manual

Introduction to Chemical Engineering Thermodynamics. Chapter 7. KFUPM Housam Binous CHE 303

A Thermodynamic Analysis of a Turbojet Engine ME 2334 Course Project

Consequences of Second Law of Thermodynamics. Entropy. Clausius Inequity

Answer Key THERMODYNAMICS TEST (a) 33. (d) 17. (c) 1. (a) 25. (a) 2. (b) 10. (d) 34. (b) 26. (c) 18. (d) 11. (c) 3. (d) 35. (c) 4. (d) 19.

In the next lecture... Tutorial on ideal cycles and component performance.

Transcription:

~ Chapter 8 Gas Power Cycles Analysis (a) Process 1-2: isentropic compression. p - f ii, f T2=1j ( - VI = (300KX8)0.4 = 689K k-l I V2 - ~..., I ~=~ T2 Process 2-3: v = constant heat addition. q23,in =U3 -U2 =Cv(T3 -T2) 750kJ/kg = (0. 718kJ/kg.KXT3-689)K 2\;:::::.J; v J ~ ~ T3 = 1734K P3V3 -~--+P3 = -r;- -T2 T2 ~ = (b) Process 3-4: isentropic expansion. T4 =T3 ( ~ )k-1 =(1734K{i. 0.4 = 755K Proces.s 4-1: v = constant heat rejection. gout =U4 -Ul =Cv(T4-7j)=(0.718kJ/kg.KX755-300)K=327kJ/kg Wnet.out = gin -gout = 750-327 = 423kJ/kg w 'lth = ne!,qut 423 kj /k~ (c) qin - = 56.4% 750 kj /kg (d) R7] h87kpa.m 3/kg.K }30~ = O.906m 3/kg = V max VI =T= 95kPa v. - v v 2 -max -- mm- r = 423kJ/kg ( kpa.m 31 ~6m3/kgJ~ -l/8)l ~ j = 534kPa 8-14

8-45 An air-standard Diesel cycle with a compression ratio of 16 and a cutoff ratio of 2 is considered. The temperature after the heat addition process, the thermal efficiency, and the mean effective pressure are to be determined. Assumptions 1 The air-standard assumptions are applicable. 2 Kinetic and potential energy changes are negligible. 3 Air is an ideal gas with variable specific heats. Properties The properties of air are given in Table A-17. Analysis (a) Process 1-2: isentropic compression. p ~in '(... U1 = 214.07 kj /kg 7)=300K ~ v'i=621.2 ~qout 1 V2 1 v =-v =-v =- T, TI TI.VI r 1 (621.2)=38.825~h2 T2 =862.4 =890.9kJ/kgK 16 v Process 2-3: P = constant heat addition. (b) q;n = h3 -hz = 1910.6-890.9 = 1019.7 kj Ikg Process 3-4: isentropic expansion. (c) Wnel,OUl = qin -qoul = 1019.7-445.63 = 574.07kJ/kg v =~= (0.287kPa.m3/kg.K}3 0~1-3 - I PI 95kPa -0.906m /kg -v max v = V2 = mm MEP= ~ ~ VI -V2 r l 3 = Wnet,out = 574.07kJ/kg kpa.m ) = 675 9kPa vi(i-i/r) (0.906m3/kgJl~I/I6) kj. 8-21

8-52 A four-cylinder ideal diesel engine with air as the working fluid has a compression ratio of 17 and a cutoff ratio of 2.2. The power the engine will deliver at 1500 rpm is to be determined. Assumptions 1 The air-standard assumptions are applicable. 2 Kinetic and potential energy changes are negligible. 3 Air is an ideal gas with constant specific heats. Properties The properties of air at room temperature are Cp = 1.005 kj/kg. K, Cy = 0.7 18 kj/kg. K, and k = 1.4 (Table A-2). p Analysis Process 1-2: isentropic compression. 2 Qin 3 (, k-t Vt T2 =Tt - = (300K Xl7 )04 = 931.8K V2 Process 2-3: p = constant heat addition. ~ T3 -~---+T3 = -T2 V2 Process 3-4: isentropic expansion. ~'4o-.,~ v T4 =T3(~ l V4 11-1 n-1 =T (2.2V2 Jl- V4 =T3(7,,-1 = 904.8K m=!jyl-~ - (97 kpa)(o.oo3 m3) RT1 (0.287 kpa.m3 /kg. K)(300 K) = 3.380 x 10-3kg Qjn =m(h3 -h2)=mcp(t3 -T2) = (3.380 x 10-3 kg)(1.005 k1/kg. K)(2050-931.8)K = 3.798 kj QOUl = m(u4 -UI )= mcv(t4-1; ) = ~.380x 10-3kgJo.718 kj/kg. KX904.8-300)K = 1.468 k1 w nel '.OUI = Q;n -QOUI = 3.798-1.468 = 2.330 kj/rev Wnel.OUI =riwnel.oul =(1500/60rev/sX2.330k1/rev)=58.2 kw Discussion Note that for 2-stroke engines, 1 thermodynamic cycle is equivalent to 1 mechanical cycle (and thus revolutions). 8-28

~ Chapter 8 Gas Power Cycles 8-76 A gas-turbine power plant operates at specified conditions. The fraction of the turbine work output used to drive the compressor and the thermal efficiency are to be determined. Assumptions 1 Steady operating conditions exist. 2 The air-standard assumptions are applicable. 3 Kinetic and potential energy changes are negligible. 4 Air is an ideal gas with constant specific heats. Properties The properties of air at room temperature are Cp = 1.005 kj/kg. K and k = 1.4 (Table A-2). Analysis (a) Using constant specific heats, r =2=~=7 p PI 100 T qln =h3 -h2 =Cp(T3 -T2) ~T3 =T2 +qin/cp = 580K + (950kJ/kgy(I.OO5kJ/kg.K) 580 K- = 1525.3K T4S=T3t (P }(k-1yk =(1525.3K\7 { 1)0.4/1.4 =874.8K 300 K 1 2s~ 1 950 kjlkg/ ~~ i (3 \ ~ 4s 4 s WC.in =h2 -h1 =Cp(T2 -Tl)=(I.OO5kJ/kg.KX580-300)K=281.4kJ/kg WT.oul = 17T(h3 -h4s)= 17TC P(T3 -T4s)= (0.86Xl.OO5kJ/kg.KX1525.3-874.8)K = 562.2kJ/kg Thus, WC,;n 281.4 kj /kg = 50.1 % 'bw = -;- = 562.2 kj /kg T,oul (b) Wnet.out = WT.out -WC.in = 562.2-281.4 = 280.8 kj Ikg 17th = Wnet.out = 280.8 kj Ikg = 29.6% qin 950 kj Ikg 8-42

~ Chapter 8 Gas Power Cycles 8.91 An ideal Bray ton cycle with regeneration is considered. The effectiveness of the regenerator is 100%. The net work output and the thermal efficiency of the cycle are to be determined. Assumptions 1 The air standard assumptions are applicable. 2 Air is an ideal gas with constant specific heats at room temperature. 3 Kinetic and potential energy changes are negligible. Properties The properties of air at room temperature are Cp = 1.005 kj/kg.k and k = 1.4 (Table A-2a). Analysis Noting that this is an ideal cycle and thus the compression and expansion processes are isentropic, we have ( ) (k-i)1 k T2 =TI ~ =(300KXI0)04/1.4 =579.2K T 1200 K-1 ~ in 3 5 2 4 ( P4 )(k-)/k 1 0.4/1.4 T4 =T3 -p; =(1200K(TO) =621.5K 300 K- 1 s & = 100% --+ T5 = T4 = 621.5K and T6 = T2 = 579.2K 1]h =1-~=I-Cp(T6-T))=I-T6-TI 579.2-300 I "P(T3 -T5 ) T3 -Ts =1-=0.517 q L In j 1200-621.5, ~.TI -r ) (k-i)/ k (or,'7th=l- =1- = 0.517),T3 p )(10){).4-))/1.4 1200 Then, Wnet =Wturb,out -Wcomp,in =(h3 -h4)-(h2 -hl) =Cp[(T3 -T4)-(T2 -TI)] = (1.005 kj/kg.k)[(1200-621.5) ~ (579.2-300)]K = 300.8 kj/kg or, Wner = '71hq;n = '71h(hJ -hs) = '71hCp(TJ -Ts) = (0.517)(1.005 kj /kg.k)(1200-621.5) = 300.6 kj / kg 8-50

8.92 A Bray ton cycle with regeneration using air as the working fluid is considered. The air temperature at the turbine exit, the net work output, and the thermal efficiency are to be determined. Assumptions 1 The air standard assumptions are applicable. 2 Air is an ideal gas with variable specific heats. 3 Kinetic and potential energy changes are negligible. T Properties The properties of air are given in Table A-17. A 1. ( ) Th. f..1150 K~ na ysls a e properties o air at various states are TI =310K ~ hl =310.24kJ/kg Pr. =1.5546 310K- 2~ &:: h2s -h] 17c =~~ h2 =h1 +(h2s -h1)/17c =310.24+ (541.26-310.24y(O.75)=618.26kJ/kg T3 = 1150K ~ h3 = 1219.25kJ/kg p'j = 200.15 Thus, (b) w, net T4 = 782.8 K =WT.our -WC.in ={h3 -h4)-{h2 -h1) = {1219.25-803.14)- {618.26-310.24)= 108.09 kj/kg (c) h5 -h2 &= ~ h5 =h2 +&(h4 -h2) h4 -h2 = 618.26 + (0.65X803.14-618.26) = 738.43 kj/kg Then, qin = h3 -h5 = 1219.25-738.43 = 480.82 kj/kg 1]", = Wnel q in 8-51

8-107 A regenerative gas-turbine cycle with two stages of compression and two stages of expansion is considered. The minimum mass flow rate of air needed to develop a specified net power output is to be determined. Assumptions 1 Argon is an ideal gas with constant specific heats. 2 Kinetic and potential energy changes are negligible. Properties The properties of argon at room temperature are Cp = 0.5203 kj/kg.k and k = 1.667 (Table A- 2a). Analysis The mass flow rate will be a minimum when the cycle is ideal. That is, the turbine and the compressors are isentropic, the regenerator has an effectiveness of 100%, and the compression ratios across each compression or expansion stage are identical. In our case it is rp =.J9 = 3. Then the work inputs to each stage of compressor are identical, so are the work outputs of each stage of the turbine. ( l(k-i)/k T T2 =Ti ~) =(300KX3)0.667/1.667 =465.6K WC.in WT.oul lp6) (~~--~, T6=Ts-. =(1200K{~ Ps \3/ (k-i)/k,- -r-c--- 0.667/1667 = 773.2K = 2(h2 -hl )= 2C p(t2-1; )= 2(0.5203kJ/kg.KX465.6-300)K = 172.3kJ/kg 300 K- = 2(h5 -h6)= 2C p(t5 -T6)= 2(0.5203kJ/kg.KX1200-773.2)K = 444.1kJ/kg / s! 1200 K- Wnel =WT,oul -WC,in =444.1-172.3=271.8kJ/kg.w m=-!!!.!-= wnet 90,000 kj/s 271.8 kj/kg = 331.1 kg/s 8-60

8-113 A turbojet aircraft flying at an altitude of 9150 m is operating on the ideal jet propulsion cycle. The velocity of exhaust gases, the propulsive power developed, and the rate of fuel consumption are to be determined. Assumptions 1 Steady operating conditions exist. 2 The air standard assumptions are applicable. 3 Air is an ideal gas with constant specific heats at room temperature. 4 Kinetic and potential energies are negligible, except at the diffuser inlet and the nozzle exit. 5 The turbine work output is equal to the compressor work input. Properties The properties of air at room temperature are Cp = 1.005 kj/kg.k and k = 1.4 (Table A-2a). Analysis (a) We assume the aircraft is stationary and the air is moving towards the aircraft at a velocity of V 1 = 320 m/s. Ideally, the air will leave the diffuser with a negligible velocity (V 2 = 0). Diffuser:...t!o Ein -Eout : Msystem (steady) Ein = Eou, h1 + V? /2 = h2 + V i /2 Compressor: PJ =P4 =~PXP2)={12X62.6kPa)=751.2kPa (p ) (k-t)/ k TJ = T2 i = {291.9KXI2)04/1.4 = 593.7K Turbine: or, T5 =T4 -T3 +T2 =1400-593.7+291.9=IO98.2K 8-66

Nozzle: E, -E = L\E <:!'0 (steady) m out system Ein = EOU' h5 + V 52/2 = h6 + V 62/2 =(1400K{ ~ 1 4/1.4 \ 751.2kPa ) = 568.2K or, O=h6 -hs + ~ O=Cp(T6 -Ts)+Vi/2 2 = 1 032m/s (b) = {60 kg/sx1032-320)m1s{320 mls { ~ \ 1000 m2/s2 = 13,670 kw (c) Q;n =m(h4 -h3)=mcp(t4 -T3)=(60kg/SX1.005kJ/kg;KX1400-593.7)K = 48,620 kj/s Qj/1 ni fuel = "HV - 48,620 kj/s -- 42,700 kj/kg = 1.14 kg/s s I 8-67

..V2 l 2 2 -VI Chapter 8 Gas Power Cycles 8-117 Air enters a turbojet engine. The thrust produced by this turbojet engine is to be determined. Assumptions 1 Steady operating conditions exist. 2 The air standard assumptions are applicable. 3 Air is an ideal gas with variable specific heats. 4 Kinetic and potential energies are negligible, except at the diffuser inlet and the nozzle exit. Properties The properties of air are given in Table A-17. Analysis We assume the aircraft is stationary and the air is moving towards the aircraft at a velocity of V I = 300 mls. Taking the entire engine as our control volume and writing the steady-flow energy balance yield 7) = 280 K ~ hj = 280.13 kj /kg T2 = 700 K --4 h2 = 713.27 kj /kg Ein -out E.A = Llijsystem i- <:PO (steady) Ein = EOUl Qln + ni(hl + V( /2) = ni(h2 + V i /2) 20,000 kj/s + 7 C 300 mls +r:;;;;;;;=~ 427 C 20kg/s 1~~2 Qin =m h2-hl+~ IkJ/kg- IOOOm 2/S2 It gives V2 = 1106 mls Thus, F p = m(v2 -vi )= (20kg/sXI 106-300 )mis = 16,120N 8-71

8-141 A simple ideal Bray ton cycle with air as the working fluid is considered. The changes in the net work output per unit mass and the thermal efficiency are to be determined. Assumptions 1 The air-standard assumptions are applicable. 2 Kinetic and potential energy changes are negligible. 3 Air is an ideal gas with constant specific heats. Properties The properties of air at room temperature are R = 0.287 kj/kg.k, Cp = 1.005 kj/kg.k, Cv = 0.718 kj/kg. K, and k = 1.4 (Table A-2). Analysis Processes 1-2 and 3-4 are isentropic. Therefore, For rp = 6, ( ~ \(k-l)/k T 3' 2" T 4=TJ-!. (P ) (k-i)/k = 779.1K PJ qin =h3 -h2 =Cp(T3 -T2) = (1.005kJ/kg.KXl300-500.6)K = 803.4kJ/kg..qoul s q out = h4 -hl = C p (T 4 -TI ) = (1.005kJ/kg.KX779.1-300)K = 481.5kJ/kg Wnel = qin -qout = 803.4-481.5 = 321.9kJ/kg 1]th = =40.1% For rp = 12, 2 = TI -1.. T ( P ) (k-i)/k = (300KXI2)04/1.4 = 610.2K I PJ T 4 = T,( t 1'-1)1' : 639.2K qin =h3 -h2 =Cp(T3 -T2) = (1.005kJ/kg.KXl300-610.2)K = 693.2kJ/kg qoul =h4 -hl =Cp(T4 -TI) = (1.005kJ/kg.K X639.2-300 )K = 340.9kJ/kg Wnel = qin -qoul = 693.2-340.9 = 352.3kJ/kg = 50.8% Thus, (a) Llwnel = 352.3-321.9 = 30.4 kj/kg (increase ) I. (b) Ll17lh =50.8%-40.1%=10.7% (increase) 8-89