DS 00 Electronic Pressure Switch with IO-Link interface Stainless Steel Sensor accuracy according to IEC 60770: 0.5 % FSO Nominal pressure from 0... 00 mbar up to 0... 600 bar Digital output signal IO-Link according to specification V. Smart sensor profile Data transfer 8. kbaud contacts Analog output (optional) 0 ma or 0 0 V Special characteristics indication of measured values on a -digit LED display rotatable and configurable display module Parameter settings via IO-Link or menu (VDMA-conform) Optional versions different mechanical connections specific versions The DS 00 is equipped with an IO-Link interface as standard in order to exchange process data, diagnostic reports and status messages with a superordinate control level. The parameters are set either also via the control level or via the VDMA-compliant menu system, which can be carried out at a local level using keys. The DS 00 is designed for the mechanical engineering and plant engineering sectors. A large number of inch threads, metric threads or NPT threads are available to users in order to ensure optimum integration in the application. In addition, unusual display positions can be compensated to the multiple rotatability of the display so that the user is able to read the vital information without any problems. Preferred areas of use are Plant and Machine Engineering - machine tools - pneumatic plants - hydraulic plants BD SENSORS GmbH BD-Sensors-Straße Phone +9 (0) 9 5 / 98-0 www.bdsensors.com D - 9599 Thierstein Fax +9 (0) 9 5 / 98 - info@bdsensors.com
DS 00 Input pressure range Nominal pressure gauge [bar] -... 0 0.0 0.6 0.5 0.0 0.60.6.5 6 Nominal pressure abs. [bar] - - - - 0.0 0.60.6.5 6 Overpressure (static) [bar] 5 0.5 5 5 0 0 0 0 Burst pressure [bar] 7.5.5.5.5 7.5 7.5 5 5 5 50 Nominal pressure gauge / abs. [bar] 0 6 5 0 60 00 60 50 00 600 Overpressure (static) [bar] 0 80 80 05 0 0 600 000 000 000 Burst pressure [bar] 50 0 0 0 0 0 000 50 50 800 Vacuum resistance P N bar: fully vacuum resistant P N < bar: on request Contact Voltage supply Standard Optional Switching current 00 ma Accuracy of switching points ± 0.5 % FSO Repeatability ± 0. % FSO Switching frequency max. 00 Hz Switching cycles > 00 x 0 6 Delay time Analog output (optional) V S = 8... 0 V DC Output signal Output signal IO-Link / SIO (PNP or NPN) + PNP contact IO-Link / SIO (PNP or NPN) + NPN contact (on request) 0.0 50.0 sec Output signal Output signal Voltage (-wire) IO-Link / SIO (PNP or NPN) + 0... 0 V permissible load: R min 0 k Current (-wire) IO-Link / SIO (PNP or NPN) + 0 ma permissible load: R max 0 Accuracy nominal pressure 0. bar: ± 0.5 % FSO nominal pressure < 0. bar: ± 0.5 % FSO Influence effects supply: 0.05 % FSO load: 0. % FSO Long term stability ± 0. % FSO / year at reference conditions Response time < msec accuracy according to IEC 60770 limit point adjustment (non-linearity, hysteresis, repeatability) Thermal effects (Offset and Span) Nominal pressure P N [bar] - 0 < 0.0 0.0 > 0 Tolerance band [% FSO] ± 0.75 ± ± ± 0.75 in compensated range [ C] -0... 85 0... 70-0 85 0 70 Permissible temperatures Permissible temperatures medium: -0... 5 C electronics/environment: -0... 85 C storage: -0... 00 C Electrical protection Short-circuit protection permanent Reverse polarity protection no damage, but also no function Electromagnetic compatibility emission and immunity according to EN 66 IO-Link Interface IO-Link.; Slave Data transfer COM, 8. kbaud Mode SIO / IO-Link Standard IEC 6-9 Mechanical stability Vibration 0 g / 5 Hz khz according to DIN EN 60068--6 Shock 500 g / ms ec according to DIN EN 60068--7
DS 00 Materials Pressure port / Housing stainless steel.0 (6L) Display housing standard: PA 6.6 Seals (media wetted) standard: FKM option: EPDM others on request Diaphragm stainless steel.5 others on request Media wetted parts pressure port, seal, diaphragm Miscellaneous Display -digit, red LED display, digit height 7 mm, range of indication -999... +9999, visible range.5 x 0.5 mm, LED s for unit switching (bar, mbar, PSI, MPa) status display contact: contact : LED, green, contact : LED, yellow Operation buttons / functions according to VDMA 57- Turn-on time 0 msec Weight approx. 0 g Current consumption < 0 ma Protection class IP 65 IP67 Installation position any CE-conformity EMC Directive: 0/0/EU Pressure Equipment Directive: 0/68/EU (module A) Pressure transmitters are calibrated vertically with pressure port downwards. Changing the installation position could lead to minor zero offsets for pressure ranges P N bar. This directive is only valid for devices with maximum permissible overpressure > 00 bar. Wiring diagrams -wire-system (IO-Link / SIO with contact) -wire-system (IO-Link / SIO with analogue output) Pin configuration Electrical connections Mx (-pin) metal (without analogue output) Mx (-pin) metal (with analogue output) supply + supply signal + communication / contact contact - shield pressure port pressure port -
DS 00 Mechanical connections (dimensions in mm) standard option G/" DIN 85 G/" DIN 85 internal thread G/" DIN 85 G/" EN 87 G/" EN 87 not possible for nominal pressure PN > 0 bar and for vacuum ranges; for G/ flush absolute pressure on request /" NPT /" NPT G/" DIN 85 G/" DIN 85 flush flush 06 BD SENSORS GmbH The specifications given in this document represent the state of engineering at the time of publishing. We reserve the right to make modifications to the specifications and materials. Phone +9 (0) 9 5 / 98-0 www.bdsensors.com Fax +9 (0) 9 5 / 98 - info@bdsensors.com DS00_E_9076
Ordering code DS 00 DS 00 - - - - - - - - Pressure gauge in bar absolute in bar 7 9 7 9 Input [bar] 0.0 0 0 0 0.6 6 0 0 0.5 5 0 0 0.0 0 0 0 0.60 6 0 0 0.0 0 0.6 6 0.5 5 0.0 0 0 6.0 6 0 0 0 0 0 6 6 0 5 5 0 0 0 0 60 6 0 0 00 0 0 60 6 0 50 5 0 00 0 0 600 6 0 0-0 X 0 9 9 9 output IO-Link / SIO I O IO-Link / SIO + 0 0 V / analogue I IO-Link / SIO + 0 ma / analogue I 7 contact x PNP x NPN x PNP x NPN 5 6 consult Accuracy standard for P N 0. bar 0.5 % standard for P N < 0. bar 0.5 % 5 Electrical connection Male plug Mx (-pin) / metal M L 9 9 Mechanical connection G/" DIN 85 G/" EN 87 G/" DIN 85 G/" DIN 85, internal thread G/" EN 87 0 0 0 0 0 0 J 0 0 0 0 G/" DIN 85 with flush sensor F 0 0 G/" DIN 85 with flush sensor K 0 0 /" NPT /" NPT N 0 0 N 0 9 9 Seals FKM EPDM Special version standard 0 0 0 9 9 absolute pressure possible from 0. bar possible in combination with contact code, 6 possible in combination with contact code, 5 not possible for nominal pressure P N > 0 bar; also not possible for vacuum ranges; for G/ flush nominal pressure abs. on request 05.0.0 This dokument contains product specification; properties are not guaranteed. Detailed information about options are defined in the datasheet. Subject to change without notice.