Analyze Hydrocarbon Impurities in,3-butadiene with an Agilent J&W GS-Alua PT Column Application Note Energy and Chemicals Authors Yun Zou and Chunxiao Wang Agilent Technologies Shanghai Ltd Abstract The typical method for analyzing hydrocarbon impurities in,3-butadiene was easily and successfully transferred from an Agilent J&W GS-Alua column to an Agilent J&W GS-Alua PT column of the same dimensions with two integrated particle traps. An Agilent 78A gas chromatograph configured with a High Pressure Liquid Injector and column backflushing was used. The GS-Alua PT column exhibited the same selectivity as the GS-Alua column without integrated particle traps, and all compounds of interest were well separated. Furthermore, the GS-Alua PT column with integrated dual-ended particle trapping technology can eliate the risk of leakage or blockage at connectors, protect valves from particles that can shed from the PLOT column, and offer increased stability and reliability for valve-switching analysis. Excellent repeatability and stability were demonstrated. Introduction,3-Butadiene is a major petrochemical product and an important feedstock in the production of rubbers and plastics, such as styrene butadiene rubber and latex. The presence of trace hydrocarbon impurities in,3-butadiene, especially propadiene and alkynes including propyne (also known as methyl acetylene), can interfere with the catalytic polymerization needed to produce high quality synthetic rubber products. Therefore, identifying and quantifying trace hydrocarbon impurities in,3-butadiene is critical to producing high quality synthetic rubbers.
The Agilent J&W GS-Alua column ( m.3 mm id) was identified as an ideal column for trace impurity analysis in a previous work []. Due to the presence of small amounts of,3-butadiene dimer (4-vinylcyclohexene) and other heavier impurities, it requires over 6 utes at high temperature to bake these impurities out of the column. Otherwise, the residuals affect retention time repeatability in subsequent runs. Using backflushing with a GS-Alua PLOT column can shorten the analytical cycle time and improve repeatability. However, conventional PLOT columns have the disadvantage that the stationary phase layer is not mechanically stable, and so the shedding of particles can plug or even damage column switching valves, and cause detector contaation. For these reasons, particle traps are recommended for both ends of a regular GS-Alua column. However, connecting particle trap devices to the columns still presents a risk of leakage or blockage at the connectors. The GS-Alua PT column, which includes integrated particle traps on both ends, is particularly well suited for this type of application. Alua PLOT PT columns provide greater stability than conventional alua PLOT columns [,3]. In this work, the selectivity of the GS-Alua PT column was compared with that of the popular GS-Alua column. Repeatability and stability were also tested using backflushing with the GS-Alua PT column to analyze impurities in,3-butadiene. Materials and Methods The experiments were performed using an Agilent 78A gas chromatograph equipped with a High Pressure Liquid Injector (HPLI), split/splitless inlet, and a flame ionization detector (FID). The configuration diagram is shown in Figure. This application was based on a six-port valve for backflushing heavier components. A GS-Alua PT column was used for separation, with both ends connected with the six-port valve. By switching the valve, the column flow can be reversed for backflushing the high molecular weight impurities to the detector. The gas standard mixtures used for method development are listed in Table. Sample out Valve Carrier gas Needle Restrictor W S P C Switching the valve to reverse the column flow to backflush the heavier impurities to the detector Figure. The configuration diagram. Table. Standard mix gas. Split vent Filter Sample in EPC flow (PCM B-) GS-Alua PT No. Component Concentration (% w/w) Propane.8e- Propylene.3e- 3 iso-butane 7.6e- 4 Butane 6.78e- Propadiene 8.e- 6 t--butene.78e- 7 -Butene.4e- 8 iso-butylene.8e- C--Butene 3.74e- iso-pentane 3.3e-3 n-pentane.e-3,-butadiene.8e- 3,3-Butadiene Balance 4 Propyne.e- Vinyl acetylene.8e- 6 Ethyl acetylene.43e- Conditions Column : 6 4 3 Agilent J&W GS-Alua PT, m.3 mm, with two particle traps (p/n -3PT) Column : Agilent J&W GS-Alua, m.3 mm (p/n -3) Carrier: Helium, constant flow mode, 7. ml/ (relocked during run) Retention time locking: Propylene at 7.7 Inlet: Split/splitless, C, split ratio : Oven: 6 ºC hold 3, to ºC hold 3 at ºC/, to ºC hold 4 at ºC/, to 8 ºC hold at 3 ºC/ Valve box temperature: C Injection source: High Pressure Liquid Injector EPC flow for HPLI: 3 ml/ Sample size:. µl (liquid) Instrument: Agilent 78A GC Detector: FID, C FID
Agilent supplies BTO nonstick mm septa, /pk (p/n 83-477) Ultra Inert liner, universal (p/n -) Universal column nut (p/n 8-883) Internal nut (p/n G8-3) Flexible Metal ferrule,.3 mm id (p/n G388-76) Flexible Metal ferrule,. mm id (p/n G388-7) Ultimate Plus Deactivated fused silica, m. mm (p/n CP8), cut suitable length to connect six-port valve with FID Ultimate Plus Deactivated fused silica, m.3 mm (p/n CP83), cut suitable length to connect 6-port valve with inlet Results and Discussion Selectivity Alua PLOT columns are commonly used for light hydrocarbon separation. Selectivity of the GS-Alua column was very good for separating impurities in,3-butadiene in the previous work []. The GS-Alua PT column provided equivalent performance to that of the GS-Alua column, but with two integrated particle traps. By using a m.3 mm GS-Alua PT column and retention time locking (RTL) technology, method transfer was completed quickly. As shown in Figure and Figure 3, with or without backflushing, propyne can be well separated from,3 butadiene on both alua columns. Resolution of,-butadiene and,3-butadiene was about 4. on GS-Alua, and about 4.38 on GS-Alua PT. In summary, the selectivity of the GS-Alua PT column was equal to that of the regular GS-Alua column, therefore requiring imal method adjustments and no further method revalidation. The results also indicate that other GS-Alua column applications could be easily transferred to the GS-Alua PT column. pa pa Agilent J&W GS-Alua 4 3 6 78 Agilent J&W GS-Alua PT 3 3 4 6 Peak ID. Propane. Propylene 3. iso-butane 4. Butane. Propadiene 6. -Butene 7. t--butene 8. iso-butylene. C--Butene. iso-pentane. n-pentane.,-butadiene 3.,3-Butadiene 4. Propyne. Vinyl acetylene 6. Ethyl acetylene 7. Dimer 3 4 6 7 7 7 4 3 678 4 6 3 4 6 7 Figure. Overlay chromatograms of a standard gas mix on Agilent J&W GS-Alua and Agilent J&W GS-Alua PT columns, without backflushing. 3
pa pa Agilent J&W GS-Alua Agilent J&W GS-Alua PT 3 4 6 7 8 3 4 6 3 3 Peak ID. Propane. Propylene 3. iso-butane 4. Butane. Propadiene 6. t--butene 7. -Butene 8. iso-butylene. C--Butene. iso-pentane. n-pentane.,-butadiene 3.,3-Butadiene 4. Propyne. Vinyl acetylene 6. Ethyl acetylene 7. Dimer * Valve switching for backflushing * 7 7 3 4 6 7 8 4 6 3 Figure 3. Overlay chromatograms of a standard gas mix on Agilent J&W GS-Alua and Agilent J&W GS-Alua PT columns, with backflushing. * Integrated dual-ended particle trap technology Both ends of the regular GS-Alua column or GS-Alua PT column were connected to a six-port valve. As shown in Figure, analysis time was more than 6 utes without backflushing on both columns. The presence of dimer and other heavier impurities may contaate the column and affect repeatability in subsequent runs. It can take more than 3 utes at 8 C to bake them out of the column. One commonly used method to reduce cycle time or run time in GC analysis is to backflush late-eluting compounds from the column. Using the configuration design in this application, the column flow can be reversed by switching the valve to backflush the high molecular weight impurities to the detector after the last compound of interest elutes out of the column. The analysis time is shortened significantly (approximately 3 utes) with backflushing, as shown in Figure 3 on both GS-Alua and GS-Alua PT columns. The stationary phase layer of traditional PLOT columns is not mechanically stable, and can lead to particle shedding. In this application, the directions of column flow with backflushing and without backflushing are opposite. Therefore, particle traps are recommended on both ends of regular GS-Alua columns through unions and associated fittings. However, the GS-Alua PT column with integrated particle traps forms one continuous length of fused silica tubing, and is very suitable for this type of application. Connecting the GS-Alua PT column with the valve is very convenient and presents no risk of leakage or blockage at the connectors. 4
Repeatability and stability To evaluate the performance of the GS-Alua PT columns, injections were made of the standard gas mix to demonstrate stability and repeatability. As shown in Table, the average peak area for injections of the standard gas mix revealed low standard deviation, and had relative standard deviations (RSDs) below.% over 8 days of analyses. Good reproducibility of retention times can be achieved, and RSD obtained from replicate analyses of standard gas mix was found to be below.4%. Better intra-day reproducibility of peak area and retention time was obtained with RSD below.8% and.%, respectively. This showed that excellent repeatability and long-term precision was achieved using the Agilent J&W PLOT PT columns. No signal spikes related to particle shedding were observed in the injections. The results indicate that high molecular weight impurities were backflushed effectively, demonstrating that Agilent J&W PLOT PT columns with integrated dual-ended particle trap technology can prevent particle shedding, protect column-switching valves, and offer increased stability and reliability for valve analysis. Table. Repeatability data of a standard gas mix. Area n = RT n = Compounds Average St dev RSD % Average St dev RSD % Propane 4.88..64 4.73.6.4 Propylene.8.748.6 7.4.34.3 iso-butane 83.47.43.7 8.6.3.4 Butane 7.376.3.6.7.3.3 Propadiene.68.677.3.68.36.38 t--butene 4.8.73. 3.6.48.3 -Butene 73.663.4.7 4.334.3.37 iso-butylene 34.648 3.6.6.3..3 C--Butene 887.67.683..64.7.37 iso-pentane 7.743.6.8 6.3.6.34 n-pentane 3..7.84 6.8.4.3,-Butadiene 66.48 3.843.44 7.34.4.3,3-Butadiene 44,63.87,.44.3 7.473..33 Propyne 3.73.6..47.. Vinyl acetylene 34.8.48.3 4..8.4 Ethyl acetylene.34.4.78 6.7.87.33
Conclusions An Agilent 78A gas chromatograph configured with an Agilent J&W GS-Alua PT column with backflushing improved the analysis of hydrocarbon impurities in,3-butadiene. With equivalent selectivity, a typical GS-Alua column method was reproduced successfully on the GS-Alua PT column, with imal method adjustment and without the need for additional method revalidation. Due to integrated dual-ended particle trap technology that avoids the need for external particle traps, which have the risk of leakage or blockage at the connectors, the GS-Alua PT column exhibits excellent repeatability and stability for injections of a standard gas mix. The unique stabilization technology of the PT column also removes concerns of perforg valve-switching GC analysis with PLOT columns, for more confident day-to-day operation. References. Chunxiao Wang. Improved Gas Chromatograph Method for the Analysis of Trace Hydrocarbon Impurities in,3-butadiene; Agilent Technologies, Inc. Application Note, publication number -4EN,.. Anon. Protect your GC system from PLOT column phase shedding; Agilent Technologies, Inc. Brochure, publication number -74EN,. 3. Patrick Sasso. PLOT PT GC Columns with Integral Particle Traps Separate Gases without Particle Shedding; Agilent Technologies, Inc. Application Note, publication number -7EN, 3. For More Information These data represent typical results. For more information on our products and services, visit our Web site at www.agilent.com/chem. www.agilent.com/chem Agilent shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Information, descriptions, and specifications in this publication are subject to change without notice. Agilent Technologies, Inc., Printed in the USA January, -EN