March 2014 FPF2498 Adjustable OVP with 28 V Input OVT Load Switch Features Function Input Features ESD Operating Temperature Range Package Ordering Information Top Mark Advanced load switch 3.0 12 V 28 V Absolute Ratings on VIN 1.7 A Maximum Continuous Current Capability 80 mω R ON Typical Over-Voltage Protection (OVP) Over-Current Protection (OCP) Thermal Shutdown Under-Voltage Lockout (UVLO) Reverse Current locking (RC) 15 kv IEC 61000-4-2 Air Gap -40 to +85 C 6-all WLCSP (1.05 x 1.3 x 0.625 mm, 0.4 mm Pitch) FPF2498UCX TK Description The FPF2498 advanced load-management switch targets applications requiring a highly integrated solution. It disconnects loads powered from the DC power rail (<12 V) with stringent off-state current targets and high load capacitances (<100 µf). The FPF2498 consists of a slew-rate controlled low-impedance MOSFET switch. FPF2498 has over-voltage protection and over-temperature protection. Applications Cellular Phones, Smart Phones Tablets Related Resources For samples and questions, please contact: Analog.Switch@fairchildsemi.com. FPF2498 Evaluation oard FPF2498 VIN RC VOUT 3-6V C IN R1 OVLO OVP UVLO Charge Pump C LOAD V_IO R2 CONTROL FLAG Rpull-up OFF ON ON Thermal Shutdown GND Figure 1. lock Diagram and Typical Application Note: 1. Recommend C LOAD value be larger than 2.2 μf. FPF2498 Rev. 1.0.0
Pin Configuration Top Though View ottom View 1 2 2 1 A GND VIN VIN GND A VOUT ON 1.3mm ON VOUT C OVLO FLAG FLAG OVLO C 1.05mm Figure 2. Pin Assignments Pin Map Name Pin # Type Default State Description VIN A2 Input N/A Input voltage path VOUT 1 Output N/A Output voltage path ON 2 Input LOW On / Off control of device OVLO C1 Input FLAG C2 Open- Drain Output High-Z V IH=HIGH V IL=LOW Enabled Disabled OVP Adjustment set by R1 and R2 and is compared to 1.2 V V IN R2 / (R1+R2) >1.2 V Indicates a OVP / OCP / OTP fault GND A1 GND GND Device ground LOW / GND HIGH / V_IO Active Indicates: OVP (over 6.5 V at 3 6 V) OCP (over 2A) OTP (over 150 C) Normal Operation FPF2498 Rev. 1.0.0 2
Absolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameters Min. Max. Unit V PIN Voltage on VIN to GND, VIN to VOUT, OVLO Pins -0.3 28.0 Voltage on ON, FLAG Pins -0.3 6.0 Voltage on VOUT to GND Pins -0.3 20.0 I SW Maximum Switch Current 1.75 A t PD Total Power Dissipation at T A=25 C 1 W T J Operating Junction Temperature -40 +150 C T STG Storage Junction Temperature -65 +150 C JA ESD Thermal Resistance, Junction-to-Ambient (1-inch Square Pad of 2 oz. Copper) Electrostatic Discharge Capability IEC61000-4-2 System Level Notes: 2. Measured using 2S2P JEDEC std. PC. 3. Measured using 2S2P JEDEC PC cold plate method. Human ody Model, ANSI / ESDA / JEDEC JS-001-2012 Charged Device Model, JESD22-C101 2 Air Discharge (V IN, V ON, V OUT to GND) 15 Contact Discharge (V IN, V ON, V OUT to GND) 8 3 V 95 (2) C/W 110 (3) kv Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol Parameters Min. Max. Unit V IN Supply Voltage 3.5 12.0 V I SW Maximum Continues Switch Current (4) 1.7 A T A Ambient Operating Temperature -40 85 C Note: 4. Maximum Junction Temperature = 85 C FPF2498 Rev. 1.0.0 3
Electrical Characteristics Unless otherwise noted; V IN=3.5 to 5.5 V, T A=-40 to +85 C; typical values are at V IN=5 V and T A=25 C. Symbol Parameter Conditions Min. Typ. Max. Unit asic Operation I SD(OFF) Shutdown Current V IN=5.5 V, V OUT=0 V, V ON=GND 0.4 3.0 μa I Q Quiescent Current V IN=5.5 V, V OUT=Floating, I OUT=0 ma 90 125 μa R ON On Resistance V IN=3.7 V, I OUT=200 ma 90 V IN=5.0 V, I OUT=200 ma V IN=9 V, I OUT=200 ma V IN=12 V, I OUT=200 ma 80 105 (10) V IH ON Input Logic HIGH Voltage V IN=3.5 V to 5.5 V 1.15 V V IL ON Input Logic LOW Voltage V IN=3.5 V to 5.5 V 0.65 V V OL_FLAG FLAG Output Logic LOW Voltage V IN=5 V, I SINK=1 ma 0.10 0.20 V I FLAG_LK FLAG Output HIGH Leakage Current V IN=5 V, Switch On 0.5 μa RPD Pull-Down Resistance on ON Pin 3 MΩ Over-Voltage Protection V OV_TRIP V OVLO_SEL V OVP_ HYS Default Input OVP Lockout Voltage threshold for OVLO selection Input OVP Hysteresis V IN Rising Threshold OVLO=GND 6.2 6.5 6.8 V IN Falling Threshold OVLO=GND 6.2 V IN=3.5 V to 5.5 V, OVLO=GND 0.3 V V IN Falling Threshold OVLO=External Setting mω V 0.3 V V OVLO_TH OVLO Set Threshold V IN=3.5 to V OVLO 1.20 V t OVP V UVLO Response Time Under-Voltage Lockout I OUT=0.5 A, C L=0 µf, T A=25 C, V IN=6 V to 7 V V IN Increasing 3.2 V IN Decreasing 3.0 0.5 1 μs V UVLO_HYS UVLO Hysteresis 200 mv I RC RC Current V ON=0 V, V OUT=5.5 V, V IN=0 V 2 5 μa TSD Thermal Shutdown Dynamic Characteristics t DON Turn-On Delay (6) Shutdown Threshold 150 Return from Shutdown 130 Hysteresis 20 t ON Turn-On Time (7) V IN=5 V, R L=100 Ω, C L=10 µf, 7.3 ms t DOFF Turn-Off Delay (5,6) T A=25 C 600 µs V C 4.3 ms t R V OUT Rise Time (6) 3.0 ms t F V OUT Fall Time (5,6) 2.0 ms t OFF Turn-Off Time (5,8) 2.5 ms t READY Time for Device Ready for Large (9) CL=10 µf 5 ms Load Current Continued on the following page FPF2498 Rev. 1.0.0 4
Electrical Characteristics Unless otherwise noted; V IN=3.5 to 5.5 V, T A=-40 to +85 C; typical values are at V IN=5 V and T A=25 C. Symbol Parameter Conditions Min. Typ. Max. Unit t RESTART Over-Current lanking Time (5) V IN=5 V I OUT 1.7 A 64 ms (5) Moderate Over-Current Condition; t OCP Over-Current Response Time I OUT I LIM V OUT V IN t HOCP t FLAG_Release Hard Over-Current Response Time Over-Current/Voltage/Temp. Flag Release Time (5) Moderate Over-Current Condition; I OUT I LIM V OUT 0 V Time for Flag to Release when Fault Condition Removed Notes: 5. This parameter is guaranteed by design and characterization; not production tested. 6. t DON/t DOFF/t R/t F are defined in figure below. 7. t ON=t R + t DON. 8. t OFF=t F + t DOFF. 9. After t READY, the device is ready for maximum DC current load condition. 10. T A=25 C. 4 µs 3 µs 100 ms FPF2498 Rev. 1.0.0 5
Timing Diagram 90% V ON 10% 90% 90% V OUT 10% 10% td ON t R td OFF t F where: t DON=Delay On Time; t R=V OUT Rise Time; t ON=Turn-On Time; t DOFF=Delay Off Time; t F=V OUT Fall Time; and toff=turn Off Time. t ON Figure 3. Timing Diagram t OFF Device Fault ehavior Timing Figure 4. OCP Turn-Off Timing Diagram FPF2498 Rev. 1.0.0 6
Physical Dimensions 2X 0.03 C E F A ALL A1 INDEX AREA D 2X F 0.03 C A1 0.40 0.40 (Ø0.20) Cu Pad (Ø0.30) Solder Mask Opening TOP VIEW RECOMMENDED LAND PATTERN (NSMD PAD TYPE) 0.05 C 0.625 0.547 0.06 C E 0.378±0.018 0.208±0.021 C SEATING PLANE D SIDE VIEWS 0.40 0.40 1 2 C A OTTOM VIEW Ø0.260±0.010 6X 0.005 C A (Y) +/-0.018 (X) +/-0.018 F NOTES: A. NO JEDEC REGISTRATION APPLIES.. DIMENSIONS ARE IN MILLIMETERS. C. DIMENSIONS AND TOLERANCES PER ASMEY14.5M, 1994. D. DATUM C, THE SEATING PLANE IS DEFINED Y THE SPHERICAL CROWNS OF THE ALLS. E. PACKAGE TYPICAL HEIGHT IS 586 MICRONS ±39 MICRONS (547-625 MICRONS). F. FOR DIMENSIONS D, E, X, AND Y SEE PRODUCT DATASHEET. G. DRAWING FILENAME: UC006ACrev4. Figure 5. 6-all, Wafer-Level Chip-Scale Package (WLCSP), 2x3 Array, 0.4 mm Pitch Product D E X Y FPF2498UCX 1.300±30 1.050±30 0.325 0.250 Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/dwg/uc/uc006ac.pdf. For current packing container specifications, visit Fairchild Semiconductor s online packaging area: http://www.fairchildsemi.com/packing_dwg/pkg-uc006ac.pdf. FPF2498 Rev. 1.0.0 7
FPF2498 Rev. 1.0.0 8 FPF2498 Adjustable OVP with 28 V Input OVT Load Switch