Electronic Indicators / Dial Gauges / Dial Test Indicators (Lever-Type)

Electronic Indicators/Dial Gauges/Dial Test Indicators (Lever-Type) Electronic Indicators / Dial Gauges / Dial Test Indicators (Lever-Type) E-1

DIN 2270 NF E 11-053 TESATAST Dial Test Indicators (Lever-Type) These lever-type dial test indicators are especially intended for use on the shop floor or in the inspection room Ideally suited for comparative measurements on a surface plate, for instance Determine form, shape and positional deviations as well as axial and runout errors. Bidirectional measuring with automatic reversal inside the movement. Continuous clockwise pointer rotation providing error-free reading. Insensitive to magnetic fields. Jeweled movement with 7 rubies. Ball-bearing lever system with measuring insert swivelling through to 240. Very low measuring force. Full-metal construction giving exceptional robustness. Monobloc housing with 3 countersunk dovetail attachments. Standard Models Well-proven lever-type dial test indicators with dial face mounted parallel to the insert s axis. Perpendicular Models Lever-type dial test indicators with dial face mounted at right angle to the insert s axis. Lateral Models Lever-type dial test indicators with dial face mounted parallel to the insert s axis, but on the flat side of the dial housing. 24 15 17,4,1 45 ø 38,4 ø 28,5 13 70 / 94 77 / 1 70 / 94 240 11,8 35,8 ø 2 8,3 7,6 11,8 35,8 11,8 35,8 60 8,54 1,65 6,4 ø 1 Technical Data 0,02 0,01 0,002 Deviation span 27 µm µm 2 µm Deviation span within the local measuring span 0,20 12 µm 0, 5 µm 0,02 1 µm Total deviation span 31 µm 13 µm 3,5 µm Repeatability limit 4 µm 3 µm 1 µm Max. hysteresis 4 µm 3 µm 1,5 µm Measuring force with the following measuring inserts 12,53 long 0,15 N 0,15 N 36,53 long 0,06 N 0,06 N E-47

TESATAST Standard Models dia. Insert 18.005 0,01 0,8 28 0 0,4 0 12,53 18.006 0,01 0,8 38 0 0,4 0 12,53 18.007 0,01 0,5 28 0 0,25 0 36,53 18.008 0,01 0,5 38 0 0,25 0 36,53 18.009 0,002 0,2 28 0 0 0 12,53 18.0 0,002 0,2 38 0 0 0 12,53 in 18.20006 0.0005 0.030 1.1 0 15 0 1 18.20007 0.0005 0.030 1.5 0 15 0 1 18.20008 0.0005 0.020 1.1 0 0 1 7 /16 18.20009 0.0005 0.020 1.5 0 0 1 7 /16 18.200 0.001 0.030 1.1 0 15 0 1 18.20011 0.0001 0.008 1.1 0 4 0 1 18.20012 0.0001 0.008 1.5 0 4 0 1 18.20013 0.00005 0.008 1.5 0 4 0 1 DIN 2270 NF E 11-053 Rotating dial Very low measuring force as shown in table opposite Movement with patented shock absorber items Lever system with friction drive preventing from overload Accuracy: see table on page E-29 SWISSTAST Standard Models dia. 18.100 0,01 0,8 28 0 0,4 0 12,53 18.101 0,002 0,2 38 0 0 0 12,53 * Technical data as for the standard models, but equipped with a 2 dia. ruby ball tip No. 18.60302. Insert Supplied in a plastic case with: 1 2 dia. meas. insert 1 Key No. 18.60307 1 8 dia. fixing shank No. 18.405 Identification number Declaration of conformity TESATAST Perpendicular Models dia. Insert 18.204 0,01 0,8 28 0 0,4 0 12,53 18.205 0,01 0,5 28 0 0,25 0 36,53 18.304 0,002 0,2 38 0 0 0 12,53 in 18.20204 0.0005 0.030 1.1 0 15 0 1 18.20304 0.0001 0.008 1.5 0 4 0 1 E-48

TESATAST Lateral Models dia. Insert 18.011 0,01 0,8 28 0 0,4 0 12,53 18.012 0,02 2 38 0 1,0 0 36,53 18.013 0,002 0,2 28 0 0 0 12,53 in 18.20014 0.0005 0.030 1.1 0 15 0 1 Note for use of the TESATAST lever-type dial test indicators When the measuring insert is parallel to the workpiece surface (Fig. A), these dial test indicators give true reading as the amplification factor is 1:1. In other measuring positions (angle α in Fig. B), the effective lever length changes so that the read value need be corrected. With respect to this, also refer to the instruction manual. A B Measuring direction Measuring direction α Measuring inserts Shorten lever Tungsten carbide or ruby ball tip M1,4 coupling thread Carbide ball tip Ruby ball tip 18.60201 18.60301 1 12,53 18.60202 18.60302 2 12,53 18.60203 18.60303 3 12,53 18.60211 18.60304 1 36,53 18.60212 18.60305 2 36,53 18.60213 18.60309 3 36,53 18.60307 Key for measuring inserts Note The original measuring insert mounted on every TESATAST and other inserts with same nominal length but having different tip diameters are completely interchangeable. DIN 2270 NF E 11-053 Indicator Sets with Small Support Technical data are listed under each single product Plastic case Identification number Declaration of conformity 16.30003 Indicator sets with small support consisting of: 18.005 Dial test indicator (lever-type) 18.0 Dial test indicator (lever-type) 18.60203 Measuring insert 18.404 Fixing shank 18.405 Fixing shank 18.60307 Key for measuring inserts 16.39007 INTERAPID small support UJ 15 E-49

Dial Test Fühlhebelmessgeräte Indicators (Lever-Type) 9 Accessories for TESATAST 2 3 4 5 1 8 7 6 in 18.404 1 Fixing shank with dovetail clamp ø 4 18.504 ø 7 /32 18.405 2 Fixing shank with dovetail clamp ø 8 18.505 ø 1 /4 18.40202 3 Cylindrical fixing shank ø 8 x 80 18.50202 ø 3 /8 x 3.5 with clamp ø 5,6 ø 7 /32 18.40203 4 Rectangular fixing shank 13 x 6 x 50 18.50203 1 x 1 /4 x 2 with clamp ø 5,6 ø 7 /32 18.40404 5 Short swivel holder with cylindrical shank ø 8 x 25 18.50404 ø 3 /8 x 1 and dovetail clamp 18.40405 6 Long swivel holder with cylindrical shank ø 8 x 90 18.50405 ø 3 /8 x 3.5 and dovetail clamp 18.40406 7 Angle holder with cylindrical shank ø 8 x 25 18.50406 ø 3 /8 x 1 Clamping bore ø 8 ø 3 /8 18.40501 8 Centring shoulder for TESATAST perpendicular Cylindrical shank ø 8 x 25 18.40501 Clamping point for fixing shank ø 4 and dovetail clamp 18.60401 9 Double fixing clamp with ø 5,6 18.60401 dovetail clamp 18.40407 Long swivel holder with cylindrical shank and ø 8 x 125 dovetail clamp as well as fine adjustment Accessory sets Consisting of the following components: 18.404 18.405 18.40202 18.40203 18.40404 18.40405 18.40406 18.40501 18.60401 18.40001* No.1 18.400** No. 2 18.40703*** No. 3 in 18.504 18.505 18.50202 18.50203 18.50404 18.50405 18.50406 18.40501 18.60401 18.50001* No. 1 18.500** No. 2 18.50703*** No. 3 * Supplied with one measuring insert No. 18.60201, 18.60202 or 18.60203, one key No. 18.60307 as well as a suited case No. 18.60308. ** Supplied in a suited case No. 18.60608. *** Supplied in a suited case No.18.60702. E-50

DIN 2270 Rotating dial See table opposite ETALON Basic Dial Test Indicator (Lever-Type) Excellent price/performance relationship Extremely valuable in tough workshop environment Perform measurements on the surface plate or close to the machine Determine form, shape and positional errors and measure axial or radial runouts. Bi-directional measuring with automatic reversal inside the movement. Continuous clockwise pointer rotation providing clear unambiguous reading. Jeweled movement with rubies. Ball-bearing lever system with measuring insert swivelling through 240. One-piece housing in stainless steel with 3 dovetail attachments. 25 17,5 Lever system with friction clutch acting as load inhibitor ø 32 Accuracy as shown on the table opposite 11 43 80 Supplied in a plastic case with: 1 insert with a 2 dia. 1 key 1 shank with a 6 dia. 1 shank with a 8 dia. 240 15 ø 2 8,8 Identification number Declaration of conformity dia. Insert 18.19024 0,01 0,8 32 0 0,4 0 14 Technical data Deviation span µm Deviation span within the local measuring span 0, 5 µm Total deviation span 13 µm 60 Repeatability limit 3 µm 1,65 8,54 6,4 ø 1,5 Max. hysteresis 3 µm E-51

INTERAPID 312 Dial Test Indicators (Lever-Type) Very large measuring span Ideal for inspecting all significant size variations, e.g. on the surface plate - Measure positional, form and shape errors. Additional revolution counter for sure reading. Bidirectional measuring with automatic reversal inside the movement. Pointer rotation is thereby constant. Jeweled movement with rubies. Ball-bearing lever system with measuring insert swivelling through 2. Full-metal construction giving outstanding robustness. Monobloc housing with mounted dovetail attachments as well as a 4 swivelling shank. Regular Model Time-tested dial test indicator (lever-type) with dial face mounted parallel to the insert axis. Perpendicular Model Dial test indicator (levertype) with dial face mounted at right angle to the insert axis. 29 ø 4 Angular position of 12 for stylus insert The models INTERAPID 312 are designed to give a true reading when the angle α between the stylus and the workpiece surface is 12 (Fig. A). In other measuring positions, including the parallel position of the stylus against the workpiece surface, the values read have to be corrected (Fig. B). With regard to this, also read in the instruction manual. ø 37,5 ø 30 2 ~16 16,5 96,5 67,5 190 135 A Measuring direction Technical Data α = 12 B Measuring direction 0,01 0,002 Pointer revolution 1 2 Pointer revolution 1 2 α 30 Deviation range µm 20 µm 4 µm 8 µm Total deviation range 13 µm 23 µm 6 µm µm B Measuring direction Repeatability limit 3 µm 1 µm Max. hysteresis 3 µm 2 µm Measuring force 0,12 N 0,25 N E-52

INTERAPID 312 Regular Models dia. Inserts Rotating dial Very low measuring force as in the table on page E-34 Lever system with friction drive preventing from overload Accuracy: see table on page E-34 74.111366 0,01 1,6 37,5 0 40 0 16,5 74.111367 0,01 1,6 30 0 40 0 16,5 74.111368 0,002 0,4 37,5 0 0 15,2 74.111369 0,002 0,4 30 0 0 15,2 in 74.111370 0.0005 0.060 1.5 0 15 0 0.65 74.111371 0.0005 0.060 1.2 0 15 0 0.65 74.111965 0.0005 0.060 1.5 0 15 0 2.675 74.111374 0.001 0.060 1.2 0 15 0 0.65 74.111372 0.0001 0.016 1.5 0 4 0 0.65 74.111373 0.0001 0.016 1.2 0 4 0 0.65 Supplied in a plastic case with: 1 insert with a 2. dia. in hardened steel 1 key No. 18.60307 Identification number Declaration of conformity INTERAPID 312 Perpendicular Models dia. Insert 74.111375 0,01 1,6 37,5 0 40 0 16,5 74.111376 0,01 1,6 30 0 40 0 16,5 in 74.1113774.11 0.0005 0.060 1.5 0 15 0 0.65 74.111378 0.0005 0.060 1.2 0 15 0 0.65 74.111958 0.0005 0.060 1.5 0 15 0 2.675 74.111379 0.001 0.060 1.2 0 15 0 0.65 74.111957 0.0001 0.016 1.5 0 4 0 0.65 0 0,01 20 30 40 30 20 0 0,01 20 30 40 30 20 4 6 0 2 2 0,002 4 6 8 8 4 6 0 2 2 0,002 4 6 8 8 74.111366 74.111367 74.111368 74.111369 E-53

Full Indicator Sets with Accessories Full sets consist of: INTERAPID 312 dial test indicators as shown in the tables hereafter 74.6331 Rectangular clamp attachment 74.8942 Reducing sleeve, metric or 74.8943 Reducing sleeve, inch 74.6026 Swivel holder, metric or 74.6931 Swivel holder, inch 74.111474 Case for measuring insert 18.60307 Key for the measuring insert Technical data as listed under each single product Plastic case Identification number Declaration of conformity INTERAPID 312 Regular Models 74.111366 74.111367 74.111368 74.111369 74.6331 74.8942 74.6026 74.111474 18.60307 74.111502 74.111503 74.111504 74.111505 in 74.111370 74.111371 74.111372 74.111373 74.6331 74.8943 74.6931 74.111474 18.60307 74.111508 74.111509 74.1115 74.111511 INTERAPID 312 Perpendicular Models 74.111375 74.111376 74.6331 74.8942 74.6026 74.111474 18.60307 74.111506 74.111507 in 74.111377 74.111378 74.6331 74.8943 74.6931 74.111474 18.60307 74.111513 74.111514 E-54

Measuring Inserts for INTERAPID 312 Steel ball tips Carbide ball tips L Ball tips in hardened steel or tungsten carbide M1,7 coupling thread 74.7893 74.5993 0,01 2 16,5 74.7895 74.5994 0,01 1,5 16,5 74.7897 74.5995 0,01 0,8 16,5 74.6358 0,01 2 36,6* 74.6360 0,01 0,8 36,6* 74.1481 74.1482 0,002 2 15,2 74.1492 74.1491 0,002 1,5 15,2 74.1493 74.1507 0,002 0,8 15,2 74.1494 0,002 2 34* 74.1508 0,002 0,8 34* in 74.7899 74.5996 all** 0.080 0.650 74.7901 74.5997 all** 0.060 0.650 74.7903 74.5998 all** 0.031 0.650 74.6361 all** 0.080 1.375* 74.6363 all** 0.031 1.375* Length L of the measuring inserts * The length of the used insert changes the amplification factor of the lever system. Therefore, each read value must be doubled. ** Except for models No. 74.111965 and No. 74.111958 *** Only for model No. 74.111965 **** Only for model No. 74.111958 L 74.111913*** 0.080 2.675 74.111912**** 0.0 2.675 / in 18.60307 Key for measuring inserts 74.111474 Case for measuring inserts Note The original measuring insert mounted on every INTERAPID 312 and other inserts with same nominal length but having different tip diameters are completely interchangeable. Accessories for INTERAPID 312 74.8942 74.6331 74.6026 in 74.6331 Rectangular clamping attachment, complete 74.6331 18.40203 Rectangular attachment 13 x 6 x 50 18.50203 1 x 1 /4 x 2 with clamp ø 5,6 ø 7 /32 74.8603 Double attachment with clamping point ø 4 74.8603 and dovetail 74.6026 Swivel holder ø 8 x 133 74.6931 ø 3 /8 x 5.25 with clamping points ø 4 and dovetail 74.8942 Reducing sleeve ø 8 / ø 4 74.8943 ø 3 /8 / ø 5 /32 Rectangular fixing shank 74.111481 3 /16 x 5 /16 E-55

ROCH ROCTEST Dial Test Indicators Bidirectional measuring through automatic reversal inside the movement. Continuous clockwise pointer rotation providing clear unambiguous reading. Insensitive to magnetic fields. Jeweled movement with rubies. Ball-bearing lever mechanism with measuring insert swivelling through 240. Very low measuring force. Full-metal construction giving exceptional robustness. One-piece housing with 3 dovetail mounting attachments. ROCTEST Regular Models ø 35.1761301 0,01 0,8 28 0 0,4 0 12,53 35.1761302 0,01 0,8 38 0 0,4 0 12,53 35.1761303* 0,01 0,8 28 0 0,4 0 12,53 35.1761305 0,01 0,5 38 0 0,25 0 36,53 35.1761311 0,002 0,2 28 0 0 0 12,53 35.1761312 0,002 0,2 38 0 0 0 12,53 * Low-cost model (for information on the scope of delivery, see beneath). ROCTEST Perpendicular Models ø 35.1761321 0,01 0,8 28 0 0,4 0 12,53 35.1761322 0,01 0,8 38 0 0,4 0 12,53 35.1761331 0,002 0,2 28 0 0 0 12,53 35.1761332 0,002 0,2 38 0 0 0 12,53 ROCTEST Lateral Models 35.1761341 0,01 0,8 28 0 0,4 0 12,53 35.1761342 0,01 0,8 38 0 0,4 0 12,53 35.1761351 0,002 0,2 28 0 0 0 12,53 35.1761352 0,002 0,2 38 0 0 0 12,53 Measuring inserts ø Meas. insert Measuring insert Measuring insert DIN 2270 NF E 11-053 Rotating dial Very low measuring force (see table on page E-47) Movement with shock absorber Lever system with friction clutch acting as load inhibitor For accuracy, see in the table on page E-47. Provided in a suited plastic case including: 3 measuring inserts ø 1 No. 18.60201 ø 2 No. 18.60202 ø 3 No. 18.60203 1 key No. 18.60307 2 fixing shanks ø 4 No. 18.404 ø 8 No. 18.405 Exceptions: ROCTEST 35.1761303 in a plastic case incl.: 1 measuring insert ø 2 No. 18.60202 1 key No. 18.60307 1 fixing shank ø 8 No. 18.405 ROCTEST 35.1761305 in a plastic case incl.: 1 36,53 meas. insert ø 2 No. 18.60212 1 key No. 18.60307 1 fixing shank ø 8 No. 18.405 Identification number Carbide ball tip Ruby ball tip 18.60201 18.60301 1 12,53 18.60202 18.60302 2 12,53 18.60203 18.60303 3 12,53 18.60211 18.60304 1 36,53 18.60212 18.60305 2 36,53 18.60213 18.60309 3 36,53 18.60307 Insert key wrench Hinweis Note The original measuring insert mounted on every ROCTEST and other inserts with same nominal length but having different tip diameters are completely interchangeable. Declaration of conformity Tungsten carbide ball tip or ruby M1,4 coupling thread E-56

Regular Models Models with dial mounted parallel to the insert axis. Perpendicular Models Models with dial mounted at right angle to the insert axis. Lateral Models Models with dial mounted parallel to the insert axis, but on the lateral face of the housing. 23,5 24,4 17 ø 38,2 ø 28,4 ø 38,2 ø 28,4 18 13,9 14,8 58,3 51,2 72,7 7,4 6,5 ø 28,4 ø 38,2 240 12,5 36,5 ø 2 7,4 12,5 36,5 28,7 7,8 12,5 7,4 Note for use of the MERCER lever-type dial test indicators When the measuring insert is parallel to the workpiece surface (Fig. A), these dial test indicators give true reading as the amplification factor is 1:1. In other measuring positions (angle α in Fig. B), the effective lever length changes so that the read value need be corrected. With respect to this, also refer to the instruction manual. A B Measuring direction Measuring direction α 1,65 60 8,54 6,4 ø 1 Shorten level ROCTEST Accessories For a detailed description of the components shown in this catalogue as well as the complete accessory sets and order numbers, see on page E-50. 9 2 3 4 5 1 8 7 6 E-57

MERCER Series 300 Dial Test Indicators (Lever-Type) Bidirectional measuring through automatic reversal inside the movement. Continuous clockwise pointer rotation providing clear unambiguous reading. Insensitive to magnetic fields. Jeweled Movement with rubies. Ball-bearing lever system with measuring insert swivelling through 220. Full-metal construction giving exceptional robustness. One-piece housing with 3 dovetail mounting attachments. DIN 2270 and factory standard Rotating Dial See in the table opposite Lever system with friction clutch acting as load inhibitor Tungsten carbide ball tips Supplied in a suite plastic case including: 1 2 dia. insert 1 1 / 4 in dia. rigid fixing shank No. 18.507 A 8 dia. fixing shank (part No. 18.407 or a mounting lug (part No. 32.38013 can also be used instead of the 1 / 4 in dia. rigid shank. Both are provided at no extra cost if specified on order. Inch Versions Identification number Declaration of conformity dia. Measuring insert* in in L 1 in L 2 in N 18.26001 301-1 0.0005 0.030 27 0 15 0 0.6754 0.5278 0,25 18.26002 303-1 0.0001 0.008 27 0 4 0 0.7200 0.5724 0,25 18.26003 305-1 0.001 0.030 27 0 15 0 0.6754 0.5278 0,25 18.26004 306-1 0.0005 0.030 40 0 15 0 0.6754 0.5278 0,25 18.26005 3-1 0.001 0.080 27 0 40 0 1.800 1.6527 0,25 18.26006 312-1 0.0005 0.060 40 0 30 0 1.440 1.2035 0,25 Metric Versions dia. Measuring insert* L 1 L 2 N 18.16001 302-1 0,01 0,8 27 0 40 0 18 14,26 0,25 18.16002 304-1 0,002 0,2 27 0 0 18 14,26 0,25 18.16003 307-1 0,01 0,8 40 0 40 0 18 14,26 0,25 18.16004 311-1 0,025 2,0 27 0 0 45 41,26 0,25 18.16005 313-1 0,01 1,6 40 0 8 0 36 32,26 0,25 * For both sizes L 1 and L 2, see drawing on page E-61. E-58

.65 8 17 9.4 60 6.38 L1 L2 1.6 48.91 ø27 ø40 ø 0.79 Accuracy 0.001 in 0.0005 in 0.0001 in 0,025 0,01 0,002 Deviation range 0.0004 in 0.00012 in µm 3 µm Total deviation range 0.0005 in 0.00015 in 13 µm 4 µm Repeatability limit 0.00015 in 0.00006 in 3 µm 1 µm Max. hysteresis 0.00015 in 0.00008 in 3 µm 1 µm Note for use of the MERCER lever dial test indicators When the measuring insert is parallel to the workpiece surface (Fig. A), these dial test indicators give true reading as the amplification factor is 1:1. In other measuring positions (angle α in Fig. B), the effective lever length changes so that the read value need be corrected. With respect to this, also refer to the instruction manual. A B Measuring direction Measuring direction α Shorten lever E-59

MERCER TOP Quality Dial Test Indicators (Lever-Type) Models with extra long measuring span. Bidirectional measuring through automatic reversal inside the movement. Continuous clockwise pointer rotation providing clear unambiguous reading. Insensitive to magnetic fields. Jeweld movement with rubies. Bell-bearing lever system with measuring insert swivelling through 180. Full-metal construction giving exceptional robustness. One-piece housing with 3 dovetail mounting attachments. DIN 2270 and factory standard Rotating Dial See in the table opposite Lever system with friction clutch acting as load inhibitor Tungsten carbide ball tips For sizes, see on the previous page E-59 Inch Models dia. Measuring insert* in in in in L 1 in L 2 in N 18.26011 0.0005 0.06 0.02 1.063 0 20 0.72 0.5724 0,35 18.26012 0.0005 0.06 0.02 1.575 0 20 0.72 0.5724 0,35 18.26013 0.0005 0.12 0.04 1.063 0 20 40 1.44 1.2924 0,20 18.26014 0.0005 0.12 0.04 1.575 0 20 40 1.44 1.2924 0,20 18.26015 0.0001 0.024 0.004 1.063 0 20 40 0.72 0.5724 0,30 18.26016 0.0001 0.024 0.004 1.575 0 20 40 0.72 0.5724 0,30 Supplied in a suite plastic case including: 1 2 dia. insert 1 1 / 4 in dia. rigid fixing shank No. 18.507 A 8 dia. fixing shank (part No. 18.407 or a mounting lug (part No. 32.38013 can also be used instead of the 1 / 4 in dia. rigid shank. Both are provided at no extra cost if specified on order. Identification number Declaration of conformity Metric Models dia. Measuring insert* L 1 L 2 N 18.16011 0,01 1,5 0,5 27 0 25 50 18 14,26 0,35 18.16012 0,01 1,5 0,5 40 0 25 50 18 14,26 0,35 18.16013 0,01 3,0 1,0 27 0 50 0 36 32,26 0,20 18.16014 0,01 3,0 1,0 40 0 50 0 36 32,26 0,20 18.16015 0,002 0,6 0,1 27 0 50 0 18 14,26 0,30 18.16016 0,002 0,6 0,1 40 0 50 0 18 14,26 0,30 * For both sizes L 1 and L 2, see on page E-61. E-60

Accuracy 0.06 in 0.12 in 0.024 in 1,5 3,0 0,6 0,025 0.0005 in 0.0005 in 0.0001 in 0,01 0,01 0,002 Deviation span 0.0007 in 0.0009 in 0.0005 in 17 µm 24 µm 13 µm Total deviation span 0.0008 in 0.0012 in 0.0006 in 20 µm 30 µm 15 µm Repeatability limit 0.00015 in 0.00025 in 0.0001 in 3 µm 6 µm 1,5 µm Max. hysteresis 0.00015 in 0.00025 in 0.0001 in 3 µm 6 µm 1,5 µm Measuring Inserts Accessories for MERCER Series 300 and TOP Quality Lever Dial Test Indicators ø M1,6 L 2 Tungsten carbide ball tips 0,8 2 3 Insert length L 2 Suitable for 300 series TOP Quality M1,6 coupling thread The original measuring insert mounted on every ROCTEST and other inserts with same nominal length but having different tip diameters are completely interchangeable. Inch Models 18.660 18.66007 18.66017 0.5278 in 18.26001 18.26003 18.26004 18.66011 18.66005 18.66018 0.5724 in 18.26002 18.26011 18.26012 18.26015 18.26016 18.66013 18.66001 18.66020 1.2035 in 18.26006 18.66012 18.66008 18.66019 1.6527 in 18.26005 18.66024 18.66009 18.66025 1.2924 in 18.26013 18.26014 Metric Models 18.66014 18.66003 18.66021 14,26 18.16001 18.16011 18.16002 18.16012 18.16003 18.16016 18.66016 18.66004 18.66023 32,26 18.16005 18.16013 18.16014 18.66015 18.66006 18.66022 41,26 18.16004 E-61

Attachments for MERCER Series 300 and TOP Quality Lever-Type Dial Test Indicators For a detailed description of the components shown in this catalogue as well as the complete accessory sets and order numbers, see on page E-50. D Dovetail fixing shanks and mounting lug 18.506 Fixing shank swivelling through ± 30 ø 1 / 4 in 18.507 Rigid fixing shank ø 1 / 4 in 18.406 Fixing shank swivelling through ± 30 ø 8 18.407 Rigid fixing shank ø 8 18.408 Fixing shank swivelling through ± 30 ø 4 18.409 Rigid fixing shank ø 4 32.38013 Mounting lug 13 15 19,05 30 ø 16 ø D ø 16 9,5 6,4 ø D 26,8 30 23,8 ø 6,4 14,3 26,2 Additional Clamping Accessories For a detailed description of the components shown in this catalogue as well as the complete accessory sets and order numbers, see on page E-50. 9 2 3 4 5 1 8 7 6 E-62