Low-Drop Voltage Tracker TLE 5 G Features Output tracking tolerance ±.5% 5 ma output current Combined Tracking/Enable input Very low current consumption in off mode Low drop voltage Suitable for use in automotive electronics Wide operation range: up to V Wide temperature range: C T j 15 C Output protected against short circuit Overtemperature protection Reverse polarity proof Very small SMD-Package SCT 595 SCT 595 Type Ordering Code Package TLE 5 G Q7-A951 SCT-595 (SMD) Functional Description The TLE 5 G is a monolithic integrated low-drop voltage tracker in the very small SMD package SCT 595. It is designed to supply e.g. sensors under the severe conditions of automotive applications. Therefore the device is equipped with additional protection functions against overload, short circuit and reverse polarity. Supply voltages up to V are tracked to a reference voltage at the adjust input. Therefore the Adjust pin has to be connected to a reference voltage, e.g. to a 5 V supply on a micro-controller port. The output is able to drive a load up to 5 ma while it follows the output of a main voltage regulator within an accuracy of.5%. The TLE 5 G can be switched in stand-by mode via the adjust input which causes the current consumption to drop to very low values. This feature makes the IC suitable for low power battery applications. Data Sheet Rev.. 1-1-
TLE 5 G ADJ 1 5 GND GND Ι Q AEP581 Figure 1 Pin Configuration (top view) Pin Definitions and Functions Pin No. Symbol Function 1 ADJ Adjust/Enable input; connect to the reference voltage via ext. resistor or micro-controller port; high active input GND Ground; internally connected to pin 5 I Input voltage Q Output voltage; must be blocked by a capacitor C Q 1 µf, Ω ESR 7 Ω 5 GND Ground Data Sheet Rev.. -1-
TLE 5 G TLE 5G Ι Q - + 1 ADJ, 5 AEB58 Figure Block Diagram Data Sheet Rev.. -1-
TLE 5 G Absolute Maximum Ratings C < T j < 15 C Parameter Symbol Limit Values Unit Remarks min. max. Input Voltage V I 5 V Current I I ma internally limited Output Voltage V Q 1 V Current I Q ma internally limited Adjust Voltage V ADJ. V Current I ADJ µa internally limited Temperatures Junction temperature T j 15 C Storage temperature T stg 5 15 C Thermal Resistances Junction pin R thj-pin K/W measured to pin 5 Junction ambient R thja 99 K/W 1) 1) Worst case, regarding peak temperature; zero airflow; mounted an a PCB 8 8 1.5 mm, heat sink area mm. Note: Maximum ratings are absolute ratings; exceeding any one of these values may cause irreversible damage to the integrated circuit. Data Sheet Rev.. -1-
TLE 5 G Operating Range Parameter Symbol Limit Values Unit Remarks min. max. Input voltage V I V Adjust input voltage V ADJ.5 V Junction temperature T j 15 C Data Sheet Rev.. 5-1-
TLE 5 G Electrical Characteristics V I = 1.5 V; V ADJ >.5V; C <T j <15 C; unless otherwise specified Parameter Symbol Limit Values Unit Test Condition min. typ. max. Output Output voltage tracking accuracy V Q = V ADJ V Q Output voltage tracking accuracy Output voltage tracking accuracy V Q 5 5 mv V < V I < 8 V 1 ma < I Q < 5 ma V Q 5 5 mv V < V I < V 1 ma < I Q < 1 ma V Q 5 5 mv V < V I < 1 V 1 ma < I Q < 1 ma Drop voltage V dr 1 mv I Q = 1 ma; V ADJ >V 1) Output current I Q 5 7 ma 1) T j <15 C Output capacitor C Q 1 µf at 1 khz; Ω ESR 7 Ω Current consumption I q 1.5. ma I Q < ma I q = I I I Q Current consumption I q = I I I Q I q 8 15 µa I Q < 1 ma Quiescent current (stand-by) I q = I I I Q Current consumption (drop area) I q 1 µa V ADJ = V T j < 85 C I q ma V ADJ = V I =5V I Q = ma Load regulation V Q 15 15 mv 1 ma < I Q < ma Line regulation V Q 1 1 mv V < V I < V I Q = 1 ma 1) Measured when the output voltage VQ has dropped 1 mv from the nominal value. Data Sheet Rev.. -1-
TLE 5 G Electrical Characteristics (cont d) V I = 1.5 V; V ADJ >.5V; C <T j <15 C; unless otherwise specified Parameter Symbol Limit Values Unit Test Condition Power-Supply-Ripple- Rejection min. typ. max. PSRR db f r = 1 Hz V r =.5 V PP Adjust/Enable Input Input biasing current I ADJ.1.5 µµa V ADJ = 5 V Adjust low voltage to disable V ADJ.8 V T j < 15 C V Q off Adjust range V ADJ. V V Q V ADJ <5mV T j < 15 C... V VΙ e.g. TLE 7 TLE 7 V Q V CC TLE 78 µc 1 nf GND V ADJ 5 V I/O C Ι 1 nf Ι TLE 5G Q C 1 µ Q F R. Q Ω 5 V e.g. to sensor - + 1 ADJ, 5 AES58 Figure Application Circuit Data Sheet Rev.. 7-1-
TLE 5 G Region of Stability for C Q = 1 µf Region of Stability for C Q =. µf AED917 AED918 ESR Ω ESR Ω 1 1 1 1 1 1 1 1 8 8 1 ma I Q 5 1 ma I Q 5 Data Sheet Rev.. 8-1-
TLE 5 G Typical Performance Characteristics Tracking Accuracy V Q versus Temperature T j Tracking Accuracy V Q versus Output Current I Q AED7 15 AED71 V Q mv V Q mv 1 5 15 C 5 C - -5 - -1 - - 8 1 C 1 T j -15 1 ma 5 Ι Q Output Voltage V Q versus Adjust Voltage V ADJ, V I > V ADJ Output Voltage V Q versus Input Voltage V I, V ADJ =5V AED7 AED7 V Q V V Q V 5 5 1 1 1 V 5 1 5 V V ADJ V I Data Sheet Rev.. 9-1-
TLE 5 G Drop Voltage V DR versus Output Current I Q, V ADJ =5V Current Consumption I q versus Output Current I Q V Q mv AED7 Ι q ma AED7 5 5 1 1 1 ma 5 Output Current I Q versus Input Voltage V I Ι Q 1 ma 5 Current Consumption I q versus Input Voltage V I, V ADJ =5V Ι Q Ι Q 1 ma AED1 Ι q ma AED77 1 5 8 Tj = 5 C T j = 15 C 1 Ι = ma q Ι q = 1 ma 1 V 5 1 V V I V I Data Sheet Rev.. 1-1-
TLE 5 G Package Outlines SCT-595 (Special Package) (.1) B +.1 1. -.5 (.) 1) (.) 1) +.1. -.5.9 ±. (.) (.) +.1. -.5.95 +. acc. to DIN 78. max.5 min 1 max. M 1.1 max A.1 max.15 +.1 -. 1 max 1. ±.1 A 1.9.5 M B 1) Contour of slot depends on profile of gull-wing lead form Sorts of Packing Package outlines for tubes, trays etc. are contained in our Data Book Package Information. SMD = Surface Mounted Device Dimensions in mm Data Sheet Rev.. 11-1-
TLE 5 G Edition -1- Published by Infineon Technologies AG, St.-Martin-Strasse 5, D-8151 München Infineon Technologies AG. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as warranted characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of noninfringement, regarding circuits, descriptions and charts stated herein. Infineon Technologies is an approved CECC manufacturer. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office in Germany or our Infineon Technologies Representatives worldwide (see address list). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. Data Sheet Rev.. 1-1-