Standard Carbon Film Leaded Resistors FEATURES Securely bonded carbon film Good moisture resistance ( R max. ±.5 % R) Good long term stability ( R max. ±.5 % R, for h) Low noise (refer to graph) Suitable for general purpose commercial electronics and pulse load applications Lead (Pb)-free solder contacts Pure tin plating provides compatibility with lead (Pb)-free and lead containing soldering processes Material categorization: For definitions of compliance please see www.vishay.com/doc?9992 STANDARD ELECTRICAL SPECIFICATIONS MODEL SIZE POWER RATING P 7 W LIMITING ELEMENT VOLTAGE U max. V LCA27 27.35 3 LCA44 44.6 5 Notes Coating: Light blue. Marking: Color coded. Additional blue color marking after second band. TOLERANCE ± % RESISTANCE RANGE 2 to M 5.22 to 5.M 2 to M 5.22 to M E-SERIES E24 E24 TECHNICAL SPECIFICATIONS PARAMETER UNIT LCA27 LCA44 Rated dissipation, P 7 W.35.6 Limiting element voltage, U () max. V 3 5 Limiting voltage, short-time V 5 Insulation voltage, U ins ( min) V > 7 > 7 Thermal resistance K/W 22 4 Insulation resistance Category temperature range C - 55 to + 55 Failure rate -9 /h < Weight g.2.68 Note () Rated voltage P x R. Revision: 5-Jun-3 Document Number: 235 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
PART NUMBER AND PRODUCT DESCRIPTION Part Number: LCA2724J25 L C A 2 7 2 4 J 2 5 MODEL/SIZE VARIANT TCR VALUE TOLERANCE PACKAGING () SPECIAL LCA27 LCA44 = Neutral = Neutral See diagram 3 digit value digit multiplier Multiplier 7 = * -3 8 = * -2 9 = * - = * = * 2 = * 2 3 = * 3 4 = * 4 5 = * 5 6 = * 6 G = ± 2 % J = ± 5 % Notes The PART NUMBER shown above is to facilitate the unified part numbering system for ordering products. () Please refer to table PACKAGING. 25 = A5 22 = A2 (G53) 2 = A D5 = R5 D2 = R2 Product Description: LCA27 2K4 5 % A5 LCA27 2K4 5 % A5 Up to 2 digits = Standard MODEL RESISTANCE VALUE TOLERANCE PACKAGING () LCA27 LCA44 22K = 22 k R = ± 2 % ± 5 % A5, R5 A, R2 A2 PACKAGING MODEL PIECES/REEL CODE REEL MIN. ORDER QTY PACKAGING UNITS PIECES/BOX CODE BOX MIN. ORDER QTY PACKAGING UNITS 5 A5 LCA27 5 R5 2 A2 LCA44 2 R2 A DIMENSIONS in millimeters 6 mm L L d D e B MODEL D max. L L B d e LCA27 2.4 -.3 6. -.5 8. 53 ±.6 7.5 LCA44 4.2 -.5 2.2 -.7 4.2 53 ±.8 5. Notes Taping in according with IEC 6286-. D and L measured in according with IEC 6294. d according to IEC 63. Revision: 5-Jun-3 2 Document Number: 235 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
% RATED POWER 2 8 6 4 2-55 - 25 25 5 75 25 5 75 2 7 AMBIENT TEMP. IN C DERATING TEMPERATURE RISE TEMPERATURE RISE IN C 9 8 7 6 5 4 3 2 27 44..2.3.4.5.6.7.8.9. POWER IN W NON-LINEARITY A 3 in db 2 44 27 9 8 7 6 K K K M M NON-LINEARITY RESISTANCE VALUE [Ω] CURRENT NOISE (µv/v) 5 2 3.5.3.2..5.3.2. K K CURRENT NOISE K M 27 44 M RESISTANCE VALUE [Ω] TEMPERATURE COEFFICIENT [ -6 / C] - 2-4 - 6-8 - 44 27-2 K K K M M TEMPERATURE COEFFICIENT (mean value) between - 25 C to + 25 C deviation ± 25 % RESISTANCE CHANGE Δ RR / [%] 3 2 - - 2 K K K M M ENDURANCE RESISTANCE VALUE [Ω] at upper category temperature, 55 C h Revision: 5-Jun-3 3 Document Number: 235 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
STABILITY NOMOGRAM, TYPICAL VALUES (For handling see General Information) ϑ ü = f [ P] PARAMETER: SIZE 2.2 2..8.6.4.2..8.6.4.2 LOAD P [W] Δ RR / (t) = f [Δ RR / (t = h)] PARAMETER: TIME t = h 44 h 5 h 2 h h 27 4 2 8 6 4 2..5 TEMPERATURE RISE ϑ ü [C] RESISTANCE CHANGE Δ RR / [%] after h..5 ϑ ü = f [ϑs] PARAMETER: ϑu 2 4 6 8 2 4 6 8 FILM TEMPERATURE ϑs [ C] R-K K K M ϑu = 2 C 5 5 Δ RR / [t = h] = f [ϑs] PARAMETER: RESISTANCE VALUE 3 3.3. 2 4 6 8 2 4 6 8 RESISTANCE CHANGE Δ RR / [%] FILM TEMPERATURE ϑs [ C] 4 2 8 6 4 2 4 C 6 C 8 C C 2 C 4 C POWER RATING P [W] 44 27 POWER RATING P [W] 44 27 PULSE VOLTAGE Ü MAX. [V] Secondary conditions: Secondary conditions: a) P P7 (permissible constant a) Pϑ power at ϑu = 7 C) b) ϑu 7 C b) ϑu 7 C c) R Ω c) R Ω d) Ûmax. see diagram below d) Ûmax. see diagram below.. -5-4 -3-2 - -5-4 -3-2 - SQUARE PULSE t i (s) SQUARE PULSE t i (s) PULSE RATING P PULSE RATING P P7 2 44 27 IMPEDANCE K K K K Ω Secondary conditions: a) Pmax. see diagram below b) ϑu 7 C -5-4 -3-2 - SQUARE PULSE t i (s) MAXIMUM PULSE VOLTAGE Ω FREQUENCY IN MHz HF CHARACTERISTICS LCA27 Revision: 5-Jun-3 4 Document Number: 235 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
PERFORMANCE CHARACTERISTICS TEST CONDITIONS OF TEST REQUIREMENTS ( R/R) () Endurance test at 7 C IEC 65-, 4.25. Endurance at UCT IEC 65-, 4.25.3 Overload test IEC 65-, 4.3 Thermal shock IEC 65-, 4.9 Climatic sequence IEC 65-, 4.23 Damp heat steady state IEC 65, 4.24 Resistance to soldering heat IEC 65-, 4.8 Robustness of terminations IEC 65-, 4.6 Vibration IEC 65-, 4.22 Note () For ohmic values between and M. h at 7 C,.5 h ON,.5 h OFF 8 h at 7 C,.5. h ON,.5 h OFF h at 55 C without load 8 h at 55 C without load 2.5 x rated power or twice the limiting element voltage, 2 s for size 27; 5 s for size 44 ±.5 % ± 4. % ± 3. % ± 8. % ±.5 % Rapid change between upper and lower category temperature ±.25 % Dry heat, damp heat cyclic, cold, low air pressure ±.5 % 56 days; 4 C; 9 % to 95 % RH; loaded with. P 7 ±.5 % s at 26 C solder bath temperature ±.25 % Tensile, bending and torsion ±.25 % Frequency Hz to 5 Hz; displacement.5 mm or acceleration g; three directions; 6 h ±.25 % APPLICABLE SPECIFICATIONS CECC 4-86 EN 4; EN 65- Revision: 5-Jun-3 5 Document Number: 235 ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?9
Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. 27 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 8-Feb-7 Document Number: 9