TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74HC373AP/AF/AFW TC74HC373AP,TC74HC373AF,TC74HC373AFW Octal D-Type Latch with 3-State Output The TC74HC373A is a high speed CMOS OCTAL LATCH with 3-STATE OUTPUT fabricated with silicon gate C 2 MOS technology. It achieves the high speed operation similar to equivalent LSTTL while maintaining the CMOS low power dissipation. These 8-bit D-type latches are controlled by a latch enable input (LE) and a output enable input ( OE ). When the OE input is high, the eight outputs are in a high impedance state. All inputs are equipped with protection circuits agait static discharge or traient excess voltage. Note: xxxfw (JEDEC SOP) is not available in Japan. TC74HC373AP TC74HC373AF Features High speed: tpd = 11 (typ.) at VCC = V Low power dissipation: ICC = 4 µa (max) at Ta = 2 C High noise immunity: VNIH = VNIL = 28% VCC (min) Output drive capability: 1 LSTTL loads Symmetrical output impedance: IOH = IOL = 6 ma (min) Balanced propagation delays: tplh tphl Wide operating voltage range: VCC (opr) = 2 to 6 V Pin and function compatible with 74LS373 Pin Assignment TC74HC373AFW Weight DIP20-P-300-2.4A SOP20-P-300-1.27A SOP20-P-300-1.27 SOL20-P-300-1.27 : 1.30 g (typ.) : 0.22 g (typ.) : 0.22 g (typ.) : 0.46 g (typ.) 1
IEC Logic Symbol Truth Table Inputs Output OE LE D Q H X X Z L L X Q n L H L L L H H H X: Don t care Z: High impedance Q n : Q outputs are latched at the time when the LE input is taken to a low logic level. System Diagram 2
Absolute Maximum Ratings (Note 1) Characteristics Symbol Rating Unit Supply voltage range V CC 0. to 7 V DC input voltage V IN 0. to V CC + 0. V DC output voltage V OUT 0. to V CC + 0. V Input diode current I IK ±20 ma Output diode current I OK ±20 ma DC output current I OUT ±3 ma DC V CC /ground current I CC ±7 ma Power dissipation P D 00 (DIP) (Note 2)/180 (SOP) mw Storage temperature T stg 6 to 10 C Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Note 2: 00 mw in the range of Ta = 40 to 6 C. From Ta = 6 to 8 C a derating factor of 10 mw/ C shall be applied until 300 mw. Recommended Operating Conditio (Note) Characteristics Symbol Rating Unit Supply voltage V CC 2 to 6 V Input voltage V IN 0 to V CC V Output voltage V OUT 0 to V CC V Operating temperature T opr 40 to 8 C 0 to 1000 (V CC = V) Input rise and fall time t r, t f 0 to 00 (V CC = V) 0 to 400 (V CC = V) Note: The recommended operating conditio are required to eure the normal operation of the device. Unused inputs must be tied to either VCC or GND. 3
Electrical Characteristics DC Characteristics Characteristics Symbol Ta = Test Condition Ta = 2 C 40 to 8 C V CC (V) Min Typ. Max Min Max Unit High-level input voltage V IH 1.0 3.1 4.20 1.0 3.1 4.20 V Low-level input voltage V IL 0.0 1.3 1.80 0.0 1.3 1.80 V 1.9 1.9 High-level output voltage V OH I OH = 20 µa V IN = V IH or V IL I OH = 6 ma 4.4.9 4.18 4.31 4.4.9 4.13 V I OH = 7.8 ma.68.80.63 0.0 Low-level output voltage V OL I OL = 20 µa V IN = V IH or V IL I OL = 6 ma 0.0 0.0 7 0.26 0.33 V I OL = 7.8 ma 8 0.26 0.33 3-state output off-state current Input leakage current Quiescent supply current I OZ V IN = V IH or V IL V OUT = V CC or GND ±0. ±.0 µa I IN V IN = V CC or GND ± ±1.0 µa I CC V IN = V CC or GND 4.0 40.0 µa Timing Requirements (input: t r = t f = 6 ) Characteristics Symbol Test Condition Ta = 2 C Ta = 40 to 8 C V CC (V) Typ. Limit Limit Unit Minimum pulse width (LE) t W (H) 7 1 13 9 19 16 Minimum set-up time (Dn) t s 0 10 9 6 13 11 Minimum hold time (Dn) t h 4
AC Characteristics (input: t r = t f = 6 ) Characteristics Symbol Ta = Test Condition Ta = 2 C 40 to 8 C CL (pf) V CC (V) Min Typ. Max Min Max Unit Output traition time Propagation delay time (LE-Q) Propagation delay time (D-Q) Output enable time Output disable time t TLH t THL t plh t phl t plh t phl t pzl t pzh 0 R L = 1 kω 0 10 0 10 0 10 t plz t phz R L = 1 kω 0 Input capacitance C IN 10 10 pf Output capacitance C OUT 10 pf 20 6 42 14 12 7 19 16 42 14 12 7 19 16 39 13 11 4 18 1 30 14 13 60 12 10 12 2 21 17 3 30 12 2 21 17 3 30 12 2 21 17 3 30 12 2 21 7 1 13 1 31 26 220 44 37 1 31 26 220 44 37 1 31 26 220 44 37 1 31 26 Power dissipation capacitance C PD (Note) 38 pf Note: C PD is defined as the value of the internal equivalent capacitance which is calculated from the operating current coumption without load. Average operating current can be obtained by the equation: I CC (opr) = C PD V CC f IN + I CC /8 (per latch) And the total C PD when n pcs. of latch operate can be gained by the following equation: C PD (total) = 22 + 16 n
Package Dimeio Weight: 1.30 g (typ.) 6
Package Dimeio Weight: 0.22 g (typ.) 7
Package Dimeio Weight: 0.22 g (typ.) 8
Package Dimeio (Note) Note: This package is not available in Japan. Weight: 0.46 g (typ.) 9
Note: Lead (Pb)-Free Packages DIP20-P-300-2.4A SOP20-P-300-1.27A RESTRICTIONS ON PRODUCT USE 060116EBA The information contained herein is subject to change without notice. 021023_D TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical seitivity and vulnerability to physical stress. It is the respoibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situatio in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your desig, please eure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specificatio. Also, please keep in mind the precautio and conditio set forth in the Handling Guide for Semiconductor Devices, or TOSHIBA Semiconductor Reliability Handbook etc. 021023_A The TOSHIBA products listed in this document are intended for usage in general electronics applicatio (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ( Unintended Usage ). Unintended Usage include atomic energy control itruments, airplane or spaceship itruments, traportation itruments, traffic signal itruments, combustion control itruments, medical itruments, all types of safety devices, etc. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer s own risk. 021023_B The products described in this document shall not be used or embedded to any dowtream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulatio. 060106_Q The information contained herein is presented only as a guide for the applicatio of our products. No respoibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No licee is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. 021023_C The products described in this document are subject to the foreign exchange and foreign trade laws. 021023_E 10