Attachment MH-1 Proceeding o. 1A-011 Page 1 of 3 Due Diligence Analysis PROJCT Rush Creek I : Colorado, UA using 200 Vestas V1-2.0 wind turbines at 0 m Colorado PUC -Filings ystem FOR Xcel nergy DAT May, 201 COTACT ph: +1 20.325.153 fax: +1 20.325.11 info@3tier.com www.3tier.com Copyright All rights reserved. Vaisala claims a copyright in all proprietary and copyrightable text and graphics in this Report, the overall design of this Report, and the selection, arrangement and presentation of all materials in this Report. This work may be redistributed only in its entirety. Partial redistribution is prohibited without express written permission from Vaisala. Requests for permission may be directed to http://go.vaisala.com/renewable/. 2001 th Avenue, uite 20 eattle, A 121-253
Attachment MH-1 Proceeding o. 1A-011 Page 2 of 3 Disclaimer This report has been prepared for the use of the client named in the report for the specific purpose identified in the report. Any other party should not rely upon this report for any other purpose. This report is not to be used, circulated, quoted or referred to, in whole or in part, for any other purpose without the prior written consent of Vaisala, Inc. The conclusions, observations and recommendations contained herein attributed to Vaisala, Inc. constitute the opinions of Vaisala, Inc. For a complete understanding of the conclusions and opinions, this report should be read in its entirety. To the extent that statements, information and opinions provided by the client or others have been used in the preparation of this report, Vaisala, Inc. has relied upon the same to be accurate. hile we believe the use of such information provided by others is reasonable for the purposes of this report, no assurances are intended and no representations or warranties are made. Vaisala, Inc. makes no certification and gives no assurances except as explicitly set forth in this report.
.............................................................................................. Page...... 3.. of... 3......... Contents 1 xecutive ummary 2 1.1 ind peed Maps................................................ 3 2 Methodology 2.1 ind Resource Assessment teps........................................ 5 3 Observational Data 3.1 Tower M2301.................................................. 3.2 Tower M232.................................................. Long-term Reference 11 5 Gross Generation 12 5.1 ind Resource Variability............................................ 12 5.2 Gross Generation Variability........................................... 1 5.3 Power Curves.................................................. 1 Loss Factors 1.1 Availability.................................................... 1.2 Curtailment................................................... 1.3 ake Deficit................................................... 1. lectrical fficiency............................................... 20.5 Turbine fficiency................................................ 21. nvironmental.................................................. 21. Aggregate Loss Factor.............................................. 22 Uncertainty Analysis 2.1 Uncertainty Methodology............................................ 2.2 Uncertainty Framework Results......................................... 25 Probability of xceedances 2 Conclusion 2 Appendix Turbine Means 30.1 Vestas V1-2.0 wind turbines at 0 m..................................... 30 11 Appendix Gross Long-term Variability 3 11.1 ummary..................................................... 3 11.2 Power Capacity Maps.............................................. 0 11.3 Model imulations By 3TIR.......................................... 1 11. Project-average Long-term ind Resource Assessment............................ 3 11.5 Project-average Long-term Gross Power Capacity Assessment......................... 55 11. Long-term ind Resource Assessment for Tower M2301 at 0 m....................... 5 11. Long-term ind Resource Assessment for Tower M232 at 0 m....................... 12 Appendix Validation of Model Results 12.1 Validation of Model Results at Tower M2301................................. 12.2 Validation of Model Results at Tower M232................................. 5 References 1 1
.............................................................................................. Page........ of... 3......... xecutive ummary 1 XCUTIV UMMARY........................................................................................................................................ 3TIR has conducted a wind resource assessment of the Rush Creek I project, located in Colorado, UA. This project consists of 200 Vestas V1-2.0 wind turbines at 0 m, for a total capacity of 00.0 M. The project is located southwest of the town of Limon in a mixture of farmland and shrub-steppe terrain. A summary of the major results is provided here. Table 1 provides configuration details of the project as well as primary wind speed, generation, uncertainty results, and probability of exceedance levels associated with the P50 project estimate. The long-term reference period used in this analysis extends over 3 years (January, 10 December, 2015). The wind resource assessment yields a gross project-average long-term wind speed estimate, at hub height, of.2 m/s. The longterm mean gross generation estimate is 10. G h, with a corresponding gross capacity factor of 5.5 %. Loss factors are considered, leading to a net energy estimate of 1. Gh, with a corresponding net capacity factor of 2. %. A map of the hub height long-term mean wind speed values across the Rush Creek I project area is displayed in ind peed Maps. Project ize 00.0 M umber of Turbines 200 Turbine Type V1-2.0 Hub Height 0 m Project-Average ind peed.2 m/s Project-Average Density 0. kg/m 3 Gross Generation 10. Gh et Generation 1. Gh Gross Capacity Factor 5.5 % et Capacity Factor 2. % Aggregate Loss Factor.5 % tandard rror of 20-year stimate.3 % et-p 20-year Generation 13. Gh et-p25 20-year Generation 151. Gh et-p5 20-year Generation 125.0 Gh et-p0 20-year Generation 135. Gh et-p 20-year Capacity Factor. % et-p25 20-year Capacity Factor. % et-p5 20-year Capacity Factor 0. % et-p0 20-year Capacity Factor 3. % Table 1: Project Overview 2
.............................................................................................. Page...... 5.. of... 3......... xecutive ummary 1.1 ind peed Maps This section contains a map of MO-corrected long-term mean wind speed values at hub height (0 m) across the Rush Creek I project area. 1.1.1 0 m Hub Height 05' 00' 3 55' 3 50' 3 5' 3 0' 3 15' M232 3 15' 3 ' 3 ' M2301 3 05' 3 05' 05' 00' 3 55' 3 50' 3 5' 3 0' Project Turbines Met. Towers.0.5.0.5 0m wind speed (MO corrected) m/s Figure 1: 3-year (January, 10 December, 2015) mean wind speed at 0 m. 3
.............................................................................................. Page........ of... 3......... Methodology 2 MTHODOLOGY........................................................................................................................................ ind resource assessments are conducted using 3TIR s modeling platform that combines on-site observations with mesoscale and microscale weather simulation models. The output from the modeling system is a four-dimensional data set of modeled historical weather for each meteorological (met) tower and wind turbine location. Model output is statistically calibrated using observed data from met towers. The resulting data sets are the basis for analysis of the wind resource. The core of this modeling system is the eather Research and Forecasting (RF) umerical eather Prediction (P) model, developed in a partnership between U.. federal agencies and universities. RF is suitable for a broad spectrum of applications including air quality plume modeling, wind resource assessment, and climate modeling. RF provides a flexible and computationally efficient framework that allows the worldwide academic, government, and private research communities to contribute advancements in physics, numerical methods, and data assimilation. The RF model uses reanalysis data for initial and boundary conditions. A reanalysis data set is a coarse resolution, observational-based data set that exists for the past several decades. RF relies on the reanalysis data set to provide an accurate representation of the large-scale (hundreds of kilometers) historic flow patterns throughout the atmosphere (e.g. the location of high and low pressure centers, the position of the jet stream, etc). In addition, RF requires as input highresolution topographic and land-use data in order to accurately represent surface conditions. Land surface characteristics are derived from the arc second (approximately 300 m) resolution uropean pace Agency (A) GlobCover data set [2]. Topographic data are sourced from the huttle Radar Topography Mission (RTM) data set at 3 arc-second (approximately 0 m) resolution []. ith these primary inputs, RF then solves the dynamical and physical equations that describe the processes of the atmosphere. A nested grid configuration is used to simulate the fine-resolution, local-scale flow conditions given the large-scale state of the atmosphere (as described by the reanalysis data). The Time-Varying Microscale (TVM) Model enables high-resolution mapping (tens of meters to a few hundred meters) of meteorological fields without the computational cost of running a high-resolution P model, such as the RF model. TVM uses several techniques to analyze microscale winds. Kinematic terrain effects are applied to the wind field allowing TVM to resolve the effects of microscale terrain features, effects that are unresolved by a mesoscale P model []. A Froude number adjustment is applied [1], which incorporates terrain blocking effects on the wind flow (i.e., determine whether the wind flows over or around specific terrain features). A log-profile surface roughness adjustment is also calculated to adjust the near-surface wind fields for the effects of roughness features that could not be resolved on the coarser RF model grid. These effects are computed at each time step in the study period and are based not only on wind speed and elevation, but also on other quantities, including wind direction and the thermodynamic properties of the lower atmosphere. This enables a sophisticated time-varying spatial analysis at high-resolution. On-site observational data are incorporated into the analysis to validate and correct the raw model data from RF and TVM using a process of Model Output tatistics (MO) correction. MO uses multi-linear regression equations to remove bias and adjust the variance of the raw model output to improve the match with observational data at met tower locations. The MO equation for each met tower is fit to the observational period of record. The MO equation is then applied over the entire data set, correcting the historical period during which direct observational data are unavailable. MO corrections are distributed across the model domain using a weighting scheme that depends on horizontal and vertical distance from the met tower. A detailed analysis of the data set from each met tower ensures the integrity of the observational data before MOcorrection. Data are reviewed to ensure that: The functions to convert anemometer output to wind speed are appropriate, assuming raw data logger files and conversion functions are provided. Periods of icing affecting the accuracy of wind speed and direction measurement are excluded. ensor data affected by the tower structures may be properly accounted for. Periods of anemometer dragging and/or malfunction are excluded.
.............................................................................................. Page........ of... 3......... Methodology During wind project development, met tower sensors are usually placed lower than the hub height of the proposed wind turbines. The analysis process must extrapolate the sensor data to hub height using a wind shear coefficient. ind shear is a meteorological phenomenon in which wind speed values generally increase with height above ground level (AGL); the surrounding ground cover, trees, and topographic features such as hills and valleys can significantly affect the measured wind shear. The analysis calculates the shear coefficient from the observed data and then applies the coefficient to highest observed wind speed data to estimate wind speed values at hub height. Long-term time series at each proposed turbine location are extracted from the MO-corrected data set. These hourly time series are then combined with the manufacturer s specified power curve to compute gross capacity factor values. Applying site-specific loss factor estimates to the mean P50 gross capacity factor yields the P50 net capacity factor. Uncertainty of the measured data and modeling data is then estimated to calculate the final net capacity factors at various probabilities of exceedance. 2.1 ind Resource Assessment teps To determine the energy production potential of the proposed Rush Creek I wind project, the following procedure was implemented: 1. For the CMF RA-I [3], CAR/CP [5], and MRRA [] reanalysis data sets, simulate 3 years at.5 km resolution using RF to understand the long-term temporal variability of weather over the project site. 2. Validate time series data collected from each met tower. 3. Perform correlation analysis between observations and.5 km models to determine primary reanalysis data set for P modeling.. imulate 1 year at 500 m resolution using RF to understand the spatial variability of the wind resource at the site. 5. Run TVM to downscale 500 m RF simulation to 0 m spatial resolution.. Perform ensemble analysis to integrate effects of each long term data set including consistency checks to determine usefulness of entire 3 year period for each data set. Run MO to eliminate temporal bias and mitigate spatial bias of RF/TVM model output. Compute MO corrections at each met tower. Combine the high-resolution spatial model data with the ensemble adjusted coarser resolution long-term data, creating the final MO-corrected 0 m resolution long term data set.. Calculate the expected (P50) gross capacity factor using modeled long-term time series at each turbine location in combination with the appropriate power curve.. Perform numerical wake and turbulence modeling.. Apply wake deficit as well as other site-specific loss factor estimates to the gross capacity factor, yielding the expected (P50) net capacity factor. 11. Calculate probability of exceedance levels for the net capacity factor data based on year-to-year wind resource variation, measurement uncertainty, and modeling uncertainty. The following sections provide detail regarding the process outlined above as applied to the Rush Creek I wind project. 5
.............................................................................................. Page........ of... 3......... Observational Data 3 OBRVATIOAL DATA........................................................................................................................................ Xcel nergy provided observational data from the following towers at the proposed Rush Creek I site: Tower M2301 Tower M232 The location of each tower and the proposed turbine locations are shown in ind peed Maps, and a summary of each tower is presented in Table 2. 3TIR performed a site visit of the Rush Creek I wind project, and the data were inspected for quality control purposes following the visit. ite visit information and quality control of the observed data for each tower are described in detail within the following sections. M2301 M232 Latitude 3.130 3.223 Longitude -3.03-3.30 Time eries tart 20-Jun-11 200-Oct-21 Time eries nd 201-May-02 201-May-02 Observed 20 m ind peed.5.05 Observed 0 m ind peed.53.1 Observed 0 m ind peed..1 Average hear 0.15 0.13 Hub Height 0 m ind peed.2. Long-term 0 m ind peed.1.2 Long-term 0 m Adjustment Factor.1 %.5 % Mean Turbulence Intensity (TI) 0 m.3 % 5. % Characteristic TI 0 m. %.2 % Table 2: On-site met tower summary. Hub height wind speeds are extrapolated unless there is a sensor at the hub height. ind speed values shown above are in units of m/s. Mean and characteristic turbulence intensity are at 15 m/s.
Hearing xhibit Attachment Rush MH-1Creek I Observational Data Proceeding o. 1A-011 For Xcel nergy.............................................................................................. Page........ of...3... 3.1 Tower M2301 The M2301 Tower is located at 3.130, 3.03. The location of the tower and the turbine locations are shown in ind peed Maps. The tower is located in cultivated farmland in the eastern cluster of project turbines. The tower has instrumentation up to 0 m, with anemometers at three heights and wind vanes at two heights. A summary of instruments installed on the tower is shown in Table 3. An image of the terrain surrounding the M2301 Tower is shown in Figure 2. Instrument Anemometer Anemometer Anemometer Anemometer Anemometer Anemometer ind Vane ind Vane Height (m) 0 0 0 0 20 20 5 1 Boom Orientation 233 53 235 55 23 5 233 23 Recovery Rate.3 % 0.3 % 3. % 1. %. %.0 %.0 %.0 % Table 3: M2301 Tower instrumentation. Figure 2: Panoramic view from the base of the M2301 Tower. 3.1.1 Quality Control The observed data at the M2301 Tower were quality controlled to check for instrument malfunction and tower shadow. The tower was installed on April 2, 20, although the tower did not begin collecting data until June 11, 20. Raw data were processed using provided calibrated anemometer transfer functions. Offsets of 55 and 0 were applied to the 5 m and 1 m wind vane data, respectively, to correct for expected tower shadow regions. Due to guy wire distortion, data from direction sectors 13-153 and 31-332 were removed from the analysis for the 0 m anemometer oriented at 233. Due to guy wire distortion, data from direction sectors 12-13 and 32-30 were removed from the analysis for the 0 m anemometer oriented at 55. The logger had periods of failure from June 23-2, 2011; July 2, 2011; eptember 2-5, 2011 and eptember 1 - ovember 12, 2011. The 0 m anemometer oriented at 233 failed from February 23 - August, 2013. The pressure sensor failed from June 11, 20 - August 22, 2011. On August, 2013, the logger, temperature sensor, pressure sensor and 0 m anemometer oriented at 233 were all replaced. The tower experienced intermittent periods of icing during the winter months resulting in approximately % data loss. The overall selectively averaged 0 m wind speed data recovery rate was.2%. c 201 Vaisala, Inc.
............................................................................................. Page......... of... 3......... Observational Data 3.1.2 hear xtrapolation Observed anemometer data from M2301 were used for extrapolating top sensor level wind speed data to 0 m hub height level. A 12-by-2 table, see Figure 3 below, was developed based on observed data from the anemometers at all of the available sensor levels. These shear exponent values were then applied to the observed data using the power law extrapolation method to calculate wind speed values at 0 m. Jan Feb Mar Apr May Jun Jly Aug ep Oct ov Dec Avg Hour of Day (Local) 0 1 2 3 5 11 12 13 1 15 1 1 1 1 20 21 22 23 Avg 0.15 0.15 0.15 0.13 0.0 0.0 0.0 0.0 0.0 0.11 0.20 0.21 0.1 0.1 0.15 0.1 0.1 0.15 0.12 0. 0.0 0.0 0.0 0.0 0.11 0.1 0.1 0.21 0.21 0.20 0.1 0.1 0.15 0.1 0.1 0.1 0. 0.0 0.0 0.0 0.0 0.0 0.0 0. 0.15 0.21 0.2 0.2 0.22 0.21 0.1 0.1 0.21 0.20 0.1 0.1 0.1 0.1 0.12 0.0 0.0 0.0 0.0 0.12 0.20 0.22 0.21 0.21 0.21 0.1 0.1 0.15 0.1 0.12 0.0 0.0 0.0 0.0 0.0 0.0 0.11 0.21 0.2 0.23 0.21 0.1 0.13 0.23 0.22 0.21 0.21 0.20 0.1 0.1 0.0 0.0 0.0 0.0 0.0 0.11 0.15 0.20 0.2 0.2 0.25 0.2 0.1 0.2 0.23 0.22 0.20 0.1 0.1 0.15 0. 0.0 0.0 0.0 0.0 0.11 0.15 0.20 0.2 0.25 0.25 0.25 0.1 0.2 0.2 0.23 0.21 0.21 0.1 0.12 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.1 0.20 0.2 0.2 0.30 0.2 0.2 0.23 0.21 0.20 0.1 0.1 0.1 0.13 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.11 0.2 0.2 0.31 0.2 0.2 0.25 0.1 0.1 0.15 0.1 0.13 0.12 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.13 0.1 0.23 0.2 0.23 0.22 0.21 0.1 0.1 0.1 0. 0.0 0.0 0.0 0.11 0.22 0.23 0.22 0.20 0.1 0.15 0.15 0.15 0.15 0.15 0.1 0.11 0.0 0.0 0.0 0.0 0.0 0.12 0.20 0.20 0.1 0.15 0.1 0.20 0.1 0.1 0.1 0.15 0.13 0. 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.12 0.20 0.22 0.23 0.22 0.21 0.21 0.15 Jan Feb Mar Apr May Jun Jly Aug ep Oct ov Dec Avg Figure 3: hear exponent values for the M2301 Tower.
Hearing xhibit Attachment Rush MH-1Creek I Observational Data Proceeding o. 1A-011 For Xcel nergy.............................................................................................page......11... of...3... 3.2 Tower M232 The M232 Tower is located at 3.223, 3.30. The location of the tower and the turbine locations are shown in ind peed Maps. The decommissioned tower was located just outside the northern edge of the project area in shrub steppe terrain. The tower has instrumentation up to 0 m, with anemometers at three heights and wind vanes at two heights. A summary of instruments installed on the tower is shown in Table. An image of the terrain surrounding the M232 Tower is shown in Figure. Instrument Anemometer Anemometer Anemometer Anemometer Anemometer Anemometer ind Vane ind Vane Height (m) 0 0 0 0 20 20 5 1 Boom Orientation 250 2 2 3 250 2 Recovery Rate 52. %. %.0 %. % 52.5 %.5 % 52. % 52. % Table : M232 Tower instrumentation. Figure : Panoramic view from the base of the M232 Tower. 3.2.1 Quality Control The observed data at the M232 Tower were quality controlled to check for instrument malfunction and tower shadow. Data for the tower were provided beginning on October 21, 200. There were numerous logger and processing issue with the data until ovember 3, 20. Therefore, data before ovember 3, 20 were not used for the analysis. Offsets of 55 were applied to both wind vanes to correct for expected tower shadow regions. Logger failures occurred from June - August 23, 2011 and December 31, 2012 - August, 2013. The 0 m anemometer oriented at 250 failed from March 3 - May 2, 201. The pressure failed from ovember 3, 20 - June, 2011. Maintenance was performed on August, 2013 to replace the logger, both 0 m anemometers, the 20 m anemometer oriented at 3 along with the temperature and pressure sensors. The tower experienced intermittent periods of icing during the winter months resulting in approximately % data loss. The overall selectively averaged 0 m wind speed data recovery rate was.5%. The tower was decommissioned in early May 201. c 201 Vaisala, Inc.
............................................................................................. Page...... 12... of... 3......... Observational Data 3.2.2 hear xtrapolation Observed anemometer data from M232 were used for extrapolating top sensor level wind speed data to 0 m hub height level. A 12-by-2 table, see Figure 5 below, was developed based on observed data from the anemometers at all of the available sensor levels. These shear exponent values were then applied to the observed data using the power law extrapolation method to calculate wind speed values at 0 m. Jan Feb Mar Apr May Jun Jly Aug ep Oct ov Dec Avg Hour of Day (Local) 0 1 2 3 5 11 12 13 1 15 1 1 1 1 20 21 22 23 Avg 0.1 0.1 0.1 0.13 0.11 0. 0.0 0.0 0.0 0.0 0.0 0. 0.1 0.1 0.1 0.15 0.13 0.11 0.0 0.0 0.0 0.0 0.0 0. 0.13 0.1 0.1 0.1 0.20 0.20 0.20 0.21 0.20 0.20 0.1 0.1 0. 0.0 0.0 0.0 0.12 0.20 0.21 0.21 0.20 0.20 0.1 0.1 0.1 0.1 0. 0.0 0.0 0.0 0. 0.1 0.1 0.1 0.1 0.1 0.12 0.15 0.13 0.11 0.0 0.0 0.0 0.0 0.13 0.1 0.1 0.1 0.11 0.1 0.1 0.12 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.11 0.1 0.20 0.20 0.20 0.12 0.20 0.20 0.1 0.1 0.13 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.12 0.20 0.21 0.21 0.21 0.12 0.23 0.22 0.21 0.1 0.1 0.1 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0. 0.15 0.20 0.23 0.2 0.23 0.23 0.13 0.1 0.1 0.1 0.11 0.0 0.0 0.0 0.0 0.0 0.0 0.13 0.1 0.21 0.21 0.20 0.20 0.1 0.13 0.15 0.1 0.12 0. 0.0 0.0 0. 0.1 0.15 0.15 0.15 0.12 0.15 0.15 0.15 0.1 0.1 0.1 0.1 0.12 0.0 0.0 0.0 0.0 0.0 0.13 0.15 0.12 0.15 0.15 0.1 0.13 0.13 0.11 0.0 0.0 0.0 0.0 0.0 0. 0.1 0.15 0.1 0.1 0.13 0.1 0.1 0.1 0.1 0.11 0.0 0.0 0.0 0.0 0.0 0.0 0.12 0.15 0.1 0.1 0.1 0.1 0.13 Jan Feb Mar Apr May Jun Jly Aug ep Oct ov Dec Avg Figure 5: hear exponent values for the M232 Tower.
............................................................................................. Page...... 13... of... 3......... Long-term Reference LOG-TRM RFRC........................................................................................................................................ In order to put the short-term observational data into the climatological context, 3TIR performed a review of several long term climate data sources. 3TIR primarily relies on global reanalysis data sets for understanding long-term climate variability. The reanalysis data sets are derived from thousands of global observations, including ground based weather stations, ocean surface buoys, satellites, and weather balloons. 3TIR analyzed three major reanalysis data sets that are each produced independently by various institutions. ach data set offers an independent view of the climate, and 3TIR will consider each in determining the most appropriate data set. The statistics relating each met tower to the reanalysis data sets reviewed are shown below in Table 5, including the daily-mean explained variance, long-term climate adjustment, and considered start year statistics. Figure shows the annual-mean wind speed values extracted from each reanalysis data set across the period of record. ach time series shown in Figure has been MO-corrected using the observed data at Tower M2301. Tower Data et xplained Variance (R 2 ) Climate Adjustment tart Year M2301 MRRA 1.1%.% 12 M2301 CP/CAR 5.5%.3% 10 M2301 CMF RA-I.%.0% 10 M232 MRRA 1.5%.5% 1 M232 CP/CAR 52.2%.3% 15 M232 CMF RA-I.%.0% 10 Table 5: Daily explained variance and long-term climate adjustment values for the considered reanalysis data sets. Annual mean ind peed (m/s)....5..3.2.1.0. RA MRRA RP. 10 1 1 12 1 2000 200 200 2012 Year Figure : Time series of annual-mean wind speed data for each considered reanalysis data set. 11
............................................................................................. Page...... 1... of... 3......... Gross Generation 5 GRO GRATIO........................................................................................................................................ 5.1 ind Resource Variability This section provides an analysis of the MO-corrected model-simulated project-average wind resource at hub height. To generate the project-average wind resource time series, MO-corrected wind resource time series data are extracted at each turbine location at the appropriate height (0 m) and then averaged across all 200 turbine locations. Based on the results of 3TIR s nergy Risk Framework, the last 3 years (January, 10 December, 2015) of data have been utilized for estimating the expected future generation at Rush Creek I. The long-term mean project-average wind speed at hub height is.2 m/s. A map of the 3-year average wind speed values at 0 m is displayed in Figure 1. Gross wind speed values and average density values at each of the 200 turbine locations are provided in Appendix Turbine Means. The project-average density value at hub height is 0. kg/m 3. The distribution of hourly MO-corrected project-average wind speed values is shown below in Figure. The distribution is based on the 3 years of modeled data. The annual wind rose is shown in Figure. Figure displays the time series of gross project-average annual-mean wind speed values. Tables and 11 shown on the following pages contain tabular-formatted month-hour and monthly-mean wind speed values, respectively. Table, often referred to as a 12x2 table, shows the average diurnal profile of wind speed values for each month of the calendar year. Table 11 shows the monthly-mean wind speed value for each month of the 3-year analysis period. Annual-mean wind speed values are also displayed in the right-most column of data in Table 11. Additional analysis of the long-term variability is available in Project-average Long-term ind Resource Assessment. 1 12 eibull fit: A=.33, k=2.3 Frequency (%) 2 0 0 2 12 1 1 1 20 ind peed (m/s) Figure : Hourly distribution of simulated project-average wind speed using 1 m/s bins. (0 m/s bin contains only values 0.5.) eibull distribution is also shown with the scale (A) and shape (k) parameters listed in the legend. 12
............................................................................................. Page...... 15... of... 3......... Gross Generation Figure : Annual wind rose of the hourly-mean project-average wind direction time series. Directional bins are 22.5 wide, and the radial contour interval is %. Annual mean ind peed (m/s)....2.0.. 10 1 1 12 1 2000 200 200 2012 Year Mean wind speed =.2 m/s Figure : Time series of annual-mean project-average wind speed. Black line denotes the long-term mean. 13
............................................................................................. Page...... 1... of... 3......... Gross Generation Jan Feb Mar Apr May Jun Jly Aug ep Oct ov Dec Avg Hour of Day (MT) 0 1 2 3 5 11 12 13 1 15 1 1 1 1 20 21 22 23 Avg.2.3...3..0.5.....5..50.51..1..55...00.2.0.1.2.1.12.3.5.55.3.2.0.0..5.....0.21.0.3.5.1..2.3...33.15.01.1....00.23.51.5.3.5.0.1.5......00..0.5.3.1.15.11.55.52..0.5...03.2..1..1.0..1..30..0..53.33...0.1..5..00.0.5.0.25.1.12.23.3.33.1.20.55.22..2..1.5.1.1.03..5.0.0.33..50.3.1.2.3..3.01.5.2..30.32..2..30.2.25.1.25.1 5.3.21..1...2.2.53.03.5.52.53.0.02.5....15.23 5..00.00 5.5 5..00.20...50.5.2..5.35.1.23.35.3.0.3..2.1.22.3.3.2.1.21.52..0.53.1.3..0.11.1..2.31...3.3.15.0..01.5..0.30.1.13.35..5..5.2.0.5.33.0.5.50.5.2..5.3.0..2.25.5.5.2.1.5..1.01...0.5.30.35.5.1.5...5..0.1.2.5.0.01.5.1.5.0.5.1..1.3.0...5..5.5..33....31.2.3.1.53..05.3.5.....2.5.2 Jan Feb Mar Apr May Jun Jly Aug ep Oct ov Dec Avg 5.5.0.5.0.5.0.5.0.5.0 ind peed Figure : Hourly-mean values of simulated project-average wind speed. Vertical axis is local time. m/s 1
............................................................................................. Page...... 1... of... 3......... Gross Generation Year 10 11 12 13 1 15 1 1 1 1 10 11 12 13 1 15 1 1 1 1 2000 2001 2002 2003 200 2005 200 200 200 200 20 2011 2012 2013 201 2015 Avg Jan Feb Mar Apr May Jun Jly Aug ep Oct ov Dec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an Feb Mar Apr May Jun Jly Aug ep Oct ov Dec Avg.35.23..3...23.23..2.2.3.23.2..0.5.2..21.1.5.1.0.0.15.31.2.55...3.3.05.3..2 Avg.0.5.0.5.0.5.0.5.0.511.0 ind peed m/s Figure 11: Monthly-mean values of simulated project-average wind speed. 15
............................................................................................. Page...... 1... of... 3......... Gross Generation 5.2 Gross Generation Variability Following RF/TVM modeling and MO correction, 3 years of hourly wind speed, wind direction, temperature, and pressure time series data were extracted for each proposed turbine location at hub height. The simulated temperature and pressure data are used to normalize simulated wind speed data to the power curve s reference density with the equation V norm = V (( ρ ) 1/3) ρ0 where V norm is normalized hourly wind speed at hub height, V is simulated hourly wind speed at hub height, ρ is density calculated from simulated hourly temperature and pressure at hub height using the Ideal Gas Law, and ρ 0 is the reference density of the power curve. The turbine power curve is then applied to the normalized wind speed data using piecewise linear interpolation between the power curve points supplied by the manufacturer. Turbine specific cut-in and cut-out limits on wind speed are also applied. This allows the manufacturer s power curve to be applied to the wind speed time series to calculate gross expected energy for all proposed turbine locations for each hour over the past 3 years. Computing the nameplate capacity factor at each turbine and then averaging across all 200 turbines yields the project-wide gross capacity factor value. A turbine-by-turbine gross energy estimate is calculated by multiplying the nameplate capacity factor at each turbine by the turbine-specific nameplate capacity, and by hours. Averaging these across all 200 turbines yields the project-average gross energy estimate. Based on the results of 3TIR s nergy Risk Framework, the last 3 years (January, 10 December, 2015) of data have been utilized for estimating the expected future generation at Rush Creek I. The 3-year long-term mean gross energy estimate at the proposed Rush Creek I project is 10. Gh. Figure 12 below shows the time series of gross projectaverage annual-mean energy values. Gross energy values at each of the 200 turbine locations are provided in Appendix Turbine Means. Additional analysis of the long-term variability is available in Project-average Long-term Gross Power Capacity Assessment. Annual mean nergy (Gh) 200 200 2000 10 120 10 0 10 10 1 1 12 1 2000 200 200 2012 Year Mean nergy = 10. Gh Figure 12: Time series of annual-mean project-average gross energy. Black line denotes the long-term mean. 1
............................................................................................. Page...... 1... of... 3......... Gross Generation 5.3 Power Curves It is expected that Vestas V1-2.0 wind turbines at a hub height of 0 m will be erected at the site. The Vestas V1-2.0 power curve is shown in Figure 13 and Table. The reference density for each power curve is shown in the caption of each respective Figure and Table below. 5.3.1 Vestas V1-2.0 2200 2000 0 100 Power (k) 100 1200 00 00 00 00 200 0 0 2 12 1 1 1 20 22 2 ind peed (m/s) Figure 13: Power curve values for a Vestas V1-2.0 turbine with a reference density of 1.225 kg/m 3. ind peed Power ind peed Power ind peed Power ( m s ) (k) ( m s ) (k) ( m s ) (k) 3.0 35.0.0 12.0 15.0 2000.0 3.5.0.5 1.0 15.5 2000.0.0 155.0.0 15.0 1.0 2000.0.5 23.0.5 1.0 1.5 2000.0 5.0 32.0 11.0 1.0 1.0 2000.0 5.5 3.0 11.5 2000.0 1.5 2000.0.0 5.0 12.0 2000.0 1.0 2000.0.5 3.0 12.5 2000.0 1.5 2000.0.0 2.0 13.0 2000.0 1.0 2000.0.5 11.0 13.5 2000.0 1.5 2000.0.0 131.0 1.0 2000.0 20.0 2000.0.5 120.0 1.5 2000.0 Table : Power curve values for a Vestas V1-2.0 turbine with a reference density of 1.225 kg/m 3. 1
............................................................................................. Page...... 20... of... 3......... Loss Factors LO FACTOR........................................................................................................................................ To convert from expected gross generation to expected net generation, the following loss factor categories are considered: availability, curtailment, wake deficit, electrical efficiency, turbine efficiency, and environmental. Details for each loss factor are discussed below..1 Availability Availability losses include losses driven by turbine and transmission shutdowns caused by planned and unexpected faults..1.1 Turbine Availability 3TIR has observed that turbine availability at newly constructed wind farms achieve.0% or higher availability when averaged over an entire calendar year. Therefore, the turbine availability loss factor is estimated to be.0%..1.2 Grid Availability The ability of the electric grid to receive and transmit wind power to load centers varies by year, season and location. Issues with grid availability are very dynamic and may actually be worsened as wind penetration levels increase. Grid availability is expected to be high across the United tates. 3TIR has assumed a regional grid availability loss factor of.5% for the Rush Creek I wind energy project..1.3 Balance of Plant Availability The balance of the plant availability is based on a total of 2 hours of outage time per year per turbine for transformer inspections and maintenance. Therefore, the balance of plant availability loss factor is estimated to be.%..2 Curtailment Curtailment losses are based on forced wind plant shutdowns resulting from environmental conditions that can adversely effect the turbines. These curtailments include wind driven sector management, high wind hysteresis, extreme icing events, and extreme temperatures..2.1 ector Management tandard minimum turbine spacing of three rotor diameters perpendicular to the dominant wind direction and five rotor diameters parallel to the dominant wind direction was tested against the layout. Turbine spacing perpendicular to the prevailing wind direction is less than three rotor diameters for a significant number of turbines. Due to the tight spacing, a sector management curtailment loss factor may apply, and the layout should be verified by the turbine manufacturer to ensure sector management is properly considered. A quantitative sector management loss calculation may be performed, once details of a sector loss algorithm (if required) are provided by the turbine manufacturer. 1
............................................................................................. Page...... 21... of... 3......... Loss Factors.2.2 High ind Hysteresis High wind speed hysteresis loss potentially occurs after a turbine has shut down because of a high wind speed cut-out event. Before the turbine can re-start, the wind speed must slow down to the hysteresis cut-in wind speed. If wind speed values reduce to below the cut-out wind speed, but remain above the hysteresis cut-in wind speed, then hysteresis loss will occur. Based on 3 years of modeled hourly wind speed data, cut-out wind speed events are expected to periodically occur. The hysteresis loss factor associated with cut-out events is estimated to be.%..2.3 xtreme Temperature The Vestas V1-2.0 has an assumed operating temperature between 20 C and 0 C without an additional cold weather package. 3 years of MO-corrected temperature data were analyzed to determine the production losses due to the temperature constraints. Based on the potential power production during periods with temperatures outside the operating limits, and a total wind farm shutdown during these times, the extreme temperature loss factor is estimated to be.% due to extreme temperatures below 20 C..2. Icing hutdown Observational data were inspected for significant icing events that may lead an operator to shutdown the wind farm. The observational data suggest a curtailment associated with icing events of.0%..3 ake Deficit 3TIR s wake model is used to determine the expected wake deficit for the turbine layout. The magnitude of the losses at any given time is a combination of the gross wind field and ambient turbulence intensity across the park, the turbine layout, and physical characteristics of the installed turbines. 3TIR analyzes wakes using a proprietary time-varying wake model that analyzes the wake at every individual time within the simulated record, rather than relying on bulk statistical descriptions of the wind field. akes for each turbine are computed individually and interact in a physically consistent way, eliminating the need for posterior models to combine wakes from multiple turbines or add in deep-array effects. The single turbine wake model is based on concepts originally presented by Larsen et al. (1). [] 3TIR s internal research has shown that the low bias associated with other Larsen-derived wake models [] is a result of poorly handled wake addition rather than the underlying model. The full system has been calibrated using production numbers from permanently installed turbines under a wide range of environmental conditions, including a broad span of turbulence intensities and stability regimes. The outputs from the model are wake-induced velocity deficit and turbulence intensity at all turbine locations, and can include additional reference locations..3.1 Internal akes Internal wakes represent wakes caused by turbines within the project. The effect of wake deficit on energy output for the layout leads to an internal wake loss factor of 3.%..3.2 xternal akes xternal wakes represent additional wakes caused by turbines from surrounding wind farms. Cedar Point and Limon (Phases 1, 2 and 3) ind Farms are over 12 km to the northeast of the nearest Rush Creek I wind turbine. 3TIR considered the distances between and positions of project turbines and surrounding turbines within the context of the local wind rose and determined the surrounding wind farms to be inconsequential. 1
............................................................................................. Page...... 22... of... 3......... Loss Factors.3.3 Future akes Future wakes represent wakes caused by turbines that will be built in the future, not related to this project. extra s Golden est ind Farm will be constructed to the west and southwest of Rush Creek I with the nearest turbines being approximately km away. 3TIR considered the distances between and positions of the project turbines and proposed Golden est turbines within the context of the local wind rose and determined this future project to be inconsequential. 3TIR discovered records of Determination of o Hazard to Air avigation filed with the FAA for turbine locations for two additional areas of possible development much closer to the Rush Creek I project than Golden est. These records were filed in 2013 and 201 with one group of turbines associated with the presumed canceled Big andy Creek ind project. Another group of turbines is associated with Powerorks LLC and is also assumed to be canceled. ith no known feasible future project with wake impacts to Rush Creek I, the future wakes loss factor is assumed to be 0%..3. Total akes The total wake loss factor, including the project (i.e. internal) turbines, is 3.%. aked generation values for each individual turbine are shown in Appendix Turbine Means.. lectrical fficiency lectrical efficiency considers losses associated with the electrical systems connecting the turbines to the metering point. These systems include the on-site collection system, the substation power transformer, and the transmission line depending on the meter location. 3TIR assumes the wind farm will be metered on the low side of the substation power transformer. Given this assumption, the electrical system efficiency is expected to be.0%...1 Collection ystem fficiency The collection system efficiency covers the efficiency of all components from the turbines to the pooling substation, including the medium voltage transformer efficiency that steps up the turbine voltage to the collection system voltage...2 ubstation Power Transformer fficiency The substation power transformer converts the voltage of the collection system to the voltage of the high voltage transmission line. This analysis ends at the low side of the substation transformer and does not consider substation power transformer losses. The client is undertaking a study to determine the full substation loss...3 High Voltage Transmission Line fficiency Transmission line efficiency is dependent on the cable type, voltage, load, and the distance from the pooling substation to the plant metering point. The client has indicated that the export power will be delivered to a substation that is approximately 0 miles away which would incur additional high voltage transmission line losses. The client is undertaking a study to determine these added losses. 3TIR has not included an assumption for additional high voltage transmission line losses in this analysis. 20
............................................................................................. Page...... 23... of... 3......... Loss Factors.. Consumptive Power Consumptive power considers the fact that a wind farm consumes electrical power when generation levels are very low. This is primarily due to power required to keep generators and transformers active and ready for operations. hen the plant is operating, consumptive power is inherent to the turbine power curve and electrical efficiency assumptions. The client has specified that the wind farm will have a bidirectional meter and has requested that consumptive power of the wind farm be accounted for as an additional loss factor. 3TIR has assumed a loss factor of.5% for consumptive power..5 Turbine fficiency Turbine efficiency is based on the ability of the turbines to perform at a level relative to the manufacturer s suggested performance rating. This can be affected by many factors, including the manufacturer s warranted performance level, the turbulence, and inflow angle..5.1 Turbine Performance 3TIR s experience with operating wind farms suggests a loss factor should be applied for turbine performance. This loss factor is related to turbines not performing at the manufacturer s rated power curve. The Vestas V1-2.0 is a relatively new turbine. ithin the United tates, there are 5 projects currently under construction with this model and a limited number of operating turbines. This turbine model is based on the Vestas V0-2.0, with a longer blade and new gear box. According to a database of installed turbines created by the American ind nergy Association, there are 2,2 V0-2.0 turbines installed in the United tates. Based on the lack operational history for the Vestas V1-2.0, 3TIR suggests that a turbine performance loss factor of.0% be applied to account for the risk that the turbines do not perform exactly at the manufacturer s rated power curve..5.2 Turbulence Intensity Research has linked turbine under performance to stable atmospheric conditions. These conditions are often identified by low turbulence intensity. In addition, periods of low or high turbulence intensity can affect the specified power curve by creating a statistical averaging effect. The statistical averaging effect is assessed by comparing the average of the instantaneous wind speeds using a theoretical zero turbulence power curve against the manufacturer s power curve at given turbulence level. 3TIR analyzes the potential for both of these effects using the measured turbulence intensity and has calculated a loss factor of.%..5.3 Inflow Angle Reduced efficiency associated with extreme inflow angles is expected to be negligible; therefore, an inflow angle loss factor of 0.0% is applied.. nvironmental Potential environmental losses include turbine under-performance caused by turbine blade soiling and degradation, extreme weather conditions such as icing and thunderstorms, and changes to the surrounding environment such as tree growth. 21
............................................................................................. Page...... 2... of... 3......... Loss Factors..1 Blade oiling In locations where the ground is dry and the soil is loose, turbine blades can build up substantial amounts of soil, leading to a power curve derating. 3TIR has analyzed projects in similar terrain and has calculated a standard loss factor for cultivated farmland and shrub steppe conditions. A loss factor of.5% is applied for blade soiling...2 Blade Degradation Blade degradation, unlike blade soiling, is permanent damage caused to the turbine blades by material in hitting the blades. This can include corrosive material, such as sodium chloride (sea salt), and larger diameter soil and dirt particles. 3TIR has analyzed projects in similar terrain and has calculated a standard loss factor for cultivated farmland and shrub steppe conditions. A loss factor of.5% is applied for blade degradation. hile this elevated risk of hail applies to the general region, the probability of hail damage at the project or at an individual turbine location is relatively small. o additional loss factor has been applied for blade degradation due to hail...3 oft Icing oft icing occurs when ice builds up on the turbine blades and affects the ability of the turbine to operate optimally. oft icing is often found as shoulder events to hard ice in which loads are exceeded and turbine shutdown occurs. A loss factor of.5% is applied for soft icing... Other nvironmental Losses 3TIR has considered the effects from additional environmental losses. Average lightning density for the project is expected to be moderate relative to the state of Colorado as a whole. Local lightning density is expected to be lower than high risk lightning areas in the Midwestern and outheastern United tates. Additional losses such thunderstorms and tree growth, are expected to be negligible.. Aggregate Loss Factor Table below shows the individual loss factors for all considered categories and the aggregate loss factor. The product of all considered losses is.5%. The expected gross P50 generation is 10. Gh; therefore, the net P50 generation is the product of.5% and 10. Gh, which equals 1. Gh. Table displays the monthly-mean net values as a percent of the expected annual-mean generation value (Gh). 22
............................................................................................. Page...... 25... of... 3......... Loss Factors Loss Factor Percent Loss Project Availability Turbine Availability.0 % Balance Of Plant Availability. % Grid Availability.5 % Curtailment ector Management High ind Hysteresis. % Icing.0 % xtreme Temperature. % ake Deficit Total akes 3. % lectrical fficiency Total lectrical fficiency.0 % Consumptive Power.5 % Turbine fficiency Turbine Performance.0 % Turbulence Intensity. % Inflow Angle 0.0 % nvironmental Blade oiling.5 % Blade Degradation.5 % oft Icing.5 % Aggregate Loss Factor.5 % Table : ummary of loss factors. ector management loss has not been considered, but a calculation could be made with additional data from the turbine manufacturer. Month Gh (%) January. % February. % March. % April. % May.0 % June. % July. % August.0 % eptember. % October.2 % ovember.2 % December. % Table : Monthly-mean net values as a percent of the total annual-mean generation. 23
............................................................................................. Page...... 2... of... 3......... Uncertainty Analysis UCRTAITY AALYI........................................................................................................................................ To calculate uncertainty and estimates of probabilities of exceedance, 3TIR has utilized its nergy Risk Framework. This framework is based on theoretical propagation of error theory and models hundreds of sources of uncertainty and their relationships throughout the modeling process. ach source of uncertainty is treated in a separate model that interacts with the framework through overlying covariance models. The analysis considers the following sources of uncertainty: measurement, vertical extrapolation, MO correction, climate variability, spatial modeling, and power modeling..1 Uncertainty Methodology.1.1 Measurement Uncertainty Measurement uncertainty captures the uncertainties related to the on-site measured data utilized in the energy assessment. It is a measure of the confidence that the recorded data, which are presumed to represent the truth, actually do represent the truth. Individual components of measurement uncertainty include the following: anemometer uncertainty, benefits of utilizing redundant sensors, measurement height uncertainty, and the statistical propagation of these uncertainties through the wind shear and extrapolation calculations to estimate hub height wind speed values. Uncertainty is separately estimated for each measurement sensor, and the sensor uncertainties are aggregated together to represent the total measurement uncertainty at hub height level for each met tower. Measurement uncertainty estimates at each met tower are considered to be independent when predicting measurement uncertainty at each turbine location..1.2 Vertical xtrapolation Uncertainty If on-site measurements are not directly recorded at hub height, an uncertainty exists that the true vertical wind speed profile may differ from the assumed power law profile. A vertical extrapolation uncertainty is required to account for this uncertainty. Remote sensing and/or hub height measurements can reduce and potentially eliminate this uncertainty. Vertical extrapolation uncertainty is estimated at each met tower individually and, met tower estimates are combined assuming partial dependency on the mast and turbine heights when estimating vertical extrapolation uncertainty at the turbine locations. For example, if met towers are located in meteorologically similar environments, risk is increased that common errors are present in the vertical extrapolation process..1.3 MO Correction Uncertainty A MO Correction uncertainty is applied at each met tower that accounts for the probability that the statistical correction applied to the long term climate signal will accurately capture the true historic climate variability. The uncertainty associated with 3TIR s MO correction algorithm decreases as the training period increases. The uncertainty depends on the length of data available at the met tower and the quality of the relationship between the met tower and the long term data set. MO correction uncertainty is estimated at each met tower, and then individual uncertainties are combined to predict the uncertainty at each turbine location assuming partial dependence between each met tower. This dependence is a function of the concurrency of measurements between the met towers, since the uncertainty of this relationship will depend on common errors in the climate signal used as the reference. 2
............................................................................................. Page...... 2... of... 3......... Uncertainty Analysis.1. Climate Variability Uncertainty Climate variability uncertainty is comprised of the following individual component uncertainties: historic climate, future climate, climate change, and climate signal consistency. Historic and future climate uncertainties represent the uncertainty associated with the natural variability of the climate and whether the climate reference period or future prediction period will capture the true climate. These uncertainties are a function of the inter-annual variability and auto-correlation of the climate signal. Climate change and climate signal consistency uncertainties represent the probability of error of the future prediction because the climate of the future may not be accurately represented by the climate of the past. These uncertainties are higher if the past few years show potential trends that may point towards a changing pattern. Climate variability uncertainty is considered common across all met towers and is modeled with complete dependence in the uncertainty framework..1.5 patial Modeling Uncertainty patial modeling uncertainty is estimated by calibrating a spatial model for each met tower that applies the MO correction derived at that met tower to all the turbine locations. The individual spatial models are combined at each turbine location using weights that are a function of the total uncertainty at each met tower considering dependence and independence of each component uncertainty. patial uncertainties are a function of the geographic covariance between each met tower and turbine location. 3TIR applies two spatial modeling uncertainties: micro spatial uncertainty and macro spatial uncertainty. Micro spatial uncertainty represents the uncertainty associated with the grid resolution of the spatial model and whether the model is capturing micro scale effects. Macro spatial uncertainty represents the risk that a spatial model calibration at the location of a met tower is applicable at distances away from that met tower. This complex uncertainty is a function of all the prior uncertainties and relative proximity and complexity of each geospatial relationship. The dependence on prior uncertainties is driven by the weighting scheme of each met tower, which has uncertainty dependence. patial covariance is also considered when aggregating each individual turbine uncertainty into a project average uncertainty..1. Power Modeling Uncertainty Power modeling uncertainty considers each step in converting wind speed estimates into energy estimates. In this step, wind speed uncertainties are expanded by the wind speed to energy relationship and then the following is considered: representativeness of the modeled frequency distribution when applying the specified power curve, wakes, availabilities, electrical losses, and all other losses considered in the loss evaluation process. Power modeling uncertainties are considered to be dependent between each turbine location..2 Uncertainty Framework Results The largest contributors of uncertainty for the Rush Creek I project originates in spatial modeling and vertical extrapolation. The average weighted turbine to tower distance is approximately 11.1 km, which is high for a quality pre-construction due diligence analysis. The installation of additional, well-instrumented met towers at locations that reduce the average weighted turbine to tower distance may further reduce the spatial modeling uncertainty. The vertical extrapolation uncertainty is elevated because the turbine hub height is 20 m above the top measured met tower height. Collecting wind speed measurements at or near hub height will further reduce the vertical extrapolation uncertainty. This can be achieved by installing additional met towers with hub height measurements, or by utilizing a wind profiler device such as a Triton ODAR (onic Detection and Ranging) or LIDAR (Light Detection and Ranging). 3TIR can provide further recommendations regarding potential met tower locations, sensor configurations and wind profiler options to reduce the spatial modeling and vertical extrapolation uncertainties. Other uncertainty categories are at acceptable or typical levels. 25
............................................................................................. Page...... 2... of... 3......... Uncertainty Analysis.2.1 Met Tower Uncertainty Uncertainty values for each met tower are presented as a function of wind speed below in Table. M2301 M232 Measurement 1.2 1.1 Vertical xtrapolation 1. 1. MO Correction 0.3 0. Climate Variability 1.2 1.2 Combined Uncertainty 2.3 2.3 Table : tandard error of wind speed estimation at each met tower (%).2.2 Combined Project Uncertainties The total project uncertainties, represented as a percent of the P50 estimate are presented in Table as a function of energy. 1-year -year 20-year Measurement 1.0 1.0 1.0 Vertical xtrapolation 1. 1. 1. MO Correction 0.5 0.5 0.5 Climate Variability 3. 1. 1. patial Modeling 5.1 5.1 5.1 Power Modeling.5.5.5 Total Uncertainty.0.3.3 Table : tandard error of wind energy estimation (%) 2
............................................................................................. Page...... 2... of... 3......... Probability of xceedances PROBABILITY OF XCDAC........................................................................................................................................ Based on the estimated total project uncertainties, Tables 11 and 12 present the probability of exceedance levels associated with the P50 project estimate. Table 11 provides results in terms of Gh, while Table 12 shows results in terms of projectaverage capacity factor (%). Table 13 shows the net P50, P5, and P0 values for each calendar month. 1-year -year 20-year Gross-P50 10. 10. 10. et-p50 1. 1. 1. et-p 152.3 13. 13. et-p25 15. 152.2 151. et-p5 152.1 15.2 15. et-p5 11.3 12.5 125.0 et-p0 13. 135.1 135. et-p5 1300. 131. 131. et-p 121. 123. 125.3 Table 11: Probability of xceedance Values (Gh) 1-year -year 20-year Gross-P50 5.5 5.5 5.5 et-p50 2. 2. 2. et-p.1.. et-p25 5.0.. et-p5 1. 1.5 1.5 et-p5 0. 0. 0. et-p0 3.3 3. 3. et-p5 3.1 3. 3. et-p 3. 35.5 35.5 Table 12: Probability of xceedance Values (%) 2
............................................................................................. Page...... 30... of... 3......... Probability of xceedances et P50 20-year et P5 20-year et P0 January 12.5 122. 11. February 11. 113.0. March 10. 13. 12. April 13.3 13. 132.0 May 13.2 12.5 121. June 125.3 11. 112. July 111... August 5.0.3 2.3 eptember 11..0 2.0 October 122. 11. 1.5 ovember 123. 11.1 111.3 December 12.1 122.5 11. Table 13: Monthly Probability of xceedance Values (Gh). The monthly P5 and P0 values are not expected to sum to the annual values, since the variability of the monthly-means is greater than the variability of the annual-mean. 2
............................................................................................. Page...... 31... of... 3......... Conclusion COCLUIO........................................................................................................................................ 3TIR has conducted a wind resource assessment of the Rush Creek I project. The assessment is based on a wind turbine layout consisting of 200 Vestas V1-2.0 wind turbines at 0 m. The wind resource assessment yields a gross energy value of 10. Gh. Loss factors were considered, leading to a net energy estimate of 1. Gh. Turbine-wise values of gross energy, wake loss, and net energy are available in Appendix Turbine Means. Following the uncertainty assessment of wind speed measurement and energy modeling analysis, net probabilities of exceedance were calculated. 20-year P5 and P0 cases are 125.0 Gh and 135. Gh, respectively. 2
............................................................................................. Page...... 32... of... 3......... Appendix Turbine Means APPDIX TURBI MA........................................................................................................................................ This section contains turbine-specific elevation, wind speed, and air density, along with gross energy values, wake loss, and net energy values for each of the 200 turbines at the Rush Creek I project..1 Vestas V1-2.0 wind turbines at 0 m ind Air Gross ake et ID Latitude Longitude levation peed Density Generation Loss Generation (degrees) (degrees) (m) ( m s ) ( kg ) m 3 (Mh :: %) (%) (Mh :: %) T001 3.231-3.550 10. 1.00 11 :: 52.0 5. 33 :: 1. T002 3.23-3.10 11.0 1.00 23 :: 52.. 35 :: 2.0 T003 3.122-3.3 1.5 0.1 :: 5. 3. 33 ::. T00 3.2332-3.30 131.15 1.005 33 :: 53.3 5.3 :: 2. T005 3.15-3.0 13.12 1.00 35 :: 53. 2.2 2 :: 1. T00 3.21352-3.251 101.03 1.00 205 :: 52.5.1 23 :: 1.5 T00 3.133-3.012 1.2 0. 5 :: 5. 0. 2 :: 1. T00 3.2050-3.3215 10.0 1.00 250 :: 52..5 3 :: 1. T00 3.220-3.3 1.3 0. :: 55.3 3. 05 :: 3. T0 3.25 -.0053 1.3 0. 3 :: 55.1 3.0 5 :: 3.1 T011 3.2200-3.25 12.11 1.00 20 :: 53.0.1 32 :: 2.0 T012 3.102-3.220 150. 0.3 :: 55. 3.0 5 :: 3. T013 3.221-3. 133.11 1.005 300 :: 53.0 2. 2 :: 1.3 T01 3.212-3.15 15.1 1.003 31 :: 53.5 3.1 353 :: 1. T015 3.110-3.03 11.3 0. :: 55.. 5 ::.3 T01 3.20-3.1 1.1 1.002 35 :: 53. 2.5 20 :: 1.5 T01 3.20-3.020 15.1 1.002 3 :: 53.5 3.1 353 :: 1. T020 3.1-3.121 13.15 1.002 31 :: 53. 2. 31 :: 1. T021 3.121-3.2300 13.1 1.001 3 :: 53. 2.3 2 :: 1. T022 3.1202-3.321 10.55 0.2 3 :: 5.. 53 ::. T023 3.133-3.50 11.20 0. 1 :: 53. 2. 323 :: 1. T02 3.125-3.502 5.25 0. 55 :: 53..1 :: 2. T02 3.102-3.211 1.0 0. 211 :: 52.5.0 20 :: 1.5 T02 3.153-3.1 1.22 0. 32 :: 53. 3.1 3 :: 2.0 T02 3.13-3.005 11.1 0. 02 :: 53. 3. 35 :: 2.1 T02 3.123-3.13. 0. 21 :: 52. 3.5 2 :: 1. T030 3.1-3.0 13. 0. :: 51.2 5.2 1 :: 1.0 T031 3.15-3.52 11.1 0. 1 :: 53. 3. 32 :: 2. T032 3.10-3. 1.32 0. 35 :: 55.0 1.1 35 :: 2.0 T033 3.23232-3.532 11. 1.00 2 :: 52..0 33 :: 1. T03 3.131-3.30 1.2 0. 5 :: 5. 2.1 1 :: 2.3 T035 3.133-3. 123. 1.00 32 :: 53.2 3.5 33 :: 1. T03 3.15-3.51 2.2 0. 50 :: 5.5 2. 2 :: 2. T03 3.112-3.15 10.1 1.001 23 :: 53. 2. 35 :: 2.0 T03 3.13-3.1523 1.1 1.001 3 :: 5.0 1.5 2 :: 1. T03 3.153-3.331 10.20 1.000 3 :: 53. 2.1 21 :: 1. Table 1: Turbine-specific 3-year mean values for 200 Vestas V1-2.0 wind turbines at 0 m. Generation values are provided in terms of energy and capacity factor. (continued on next page) 30
............................................................................................. Page...... 33... of... 3......... Appendix Turbine Means ind Air Gross ake et ID Latitude Longitude levation peed Density Generation Loss Generation (degrees) (degrees) (m) ( m s ) ( kg ) m 3 (Mh :: %) (%) (Mh :: %) T00 3.130-3.50 11.1 0. 1 :: 5.0.3 :: 2. T01 3.123-3.205 11.1 1.001 2 :: 5.1 2.2 35 :: 2.0 T02 3.155-3.50 2.25 0. 50 :: 5.2 2.3 30 :: 2.0 T03 3.1553-3.2 1.2 0. 2 :: 5.1 2. 35 :: 2.1 T0 3.1302-3.3123 15. 0.2 2 :: 5.0.2 3 ::.3 T05 3.12-3.25 153.2 0.2 1 :: 55. 2.5 51 :: 3.2 T0 3.15-3.31 11.2 0. 5 :: 5..0 555 :: 3.1 T0 3.11-3.3.31 0. 25 :: 5.. 1 :: 3.5 T0 3.155-3.02 122.2 0. 5 :: 5.5 3. 51 :: 2. T0 3.151-3.112 2.22 0. :: 5.0 2. 3 :: 2.1 T050 3.155-3.502 12.3 0. :: 55.0.5 50 :: 3. T051 3.1551-3.30 12.3 0.5 50 :: 55.0. 5 :: 3. T052 3.1525-3.000 130.3 0.5 :: 55.0 3.1 53 :: 3.0 T053 3.15302-3.511 12.30 0.5 52 :: 5..3 55 :: 3.3 T05 3.10-3. 135.3 0.5 :: 55.2 3. 0 :: 3. T055 3.15030-3.021 10.5 0. 3 :: 55..5 5 ::.2 T05 3.13-3.0 150.0 1.003 300 :: 53.0 2.3 235 :: 1.3 T05 3.110-3.53 1.23 0. 1 :: 5.1 2. 33 :: 2.1 T05 3.13500-3.0 10.2 0. 555 :: 5.5 3.2 :: 2. T05 3.11-3.22 150.35 0.3 :: 55.2.5 2 :: 3. T00 3.1355-3.35 1.2 0. 5 :: 5. 1. 30 :: 2.2 T01 3.131-3.2 1.25 1.000 5 :: 5.5 2. 15 :: 2.3 T02 3.11-3.221 101.01 1.00 1 :: 52.. 32 :: 1. T03 3.202-3.1 1.02 1.00 1 :: 52.5. 32 :: 1. T05 3.112-3.02 11.2 0. 0 :: 5..5 20 :: 3.5 T0 3.1-3.32 15.2 1.000 53 :: 5. 1.1 335 :: 1. T0 3.135-3.3011 153. 0.3 05 :: 55. 2. :: 3. T0 3.13-3.2255 1.35 0.3 1 :: 55.2 3.0 550 :: 3.1 T01 3.20-3.50 11.0 1.00 25 :: 52..3 3 :: 1. T02 3.2213-3.30 13.12 1.005 320 :: 53.2 3. 351 :: 1. T05 3.111-3. 1.11 1.003 302 :: 53.1 3. 30 :: 1. T0 3.120-3.3 13.0 1.00 215 :: 52. 1. 12 :: 0. T0 3.12-3. 1.11 1.003 323 :: 53.2 2. 23 :: 1. T0 3.135-3.220 12.03 1.005 221 :: 52. 3.5 25 :: 1. T00 3.135-3.03 12.2 0. 3 :: 55. 3.3 3 :: 3. T01 3.133-3.223 1.25 1.000 55 :: 5. 0. 2 :: 1. T02 3.1-3.053 10.1 1.002 3 :: 53. 1. 300 :: 1. T03 3.150-3.000 135.3 0.5 5 :: 55.1.1 25 :: 3.5 T0 3.150-3.312 122.21 0. 2 :: 5.0. 51 :: 3.0 T0 3.132-3.233 12.25 0.5 51 :: 5.3 3. 50 :: 2. T0 3.1512-3.013 131.12 1.005 32 :: 53. 2. 30 :: 1. T00 3.11-3.503 11. 1.00 0 :: 51..1 1 :: 1.1 T01 3.111-3.11 11. 1.00 00 :: 51. 3. 135 :: 0. T02 3.2050-3.11 1.22 1.002 1 :: 53. 2.0 2 :: 1. T03 3.1331-3.11 10. 1.00 13 :: 52.1.3 2 :: 1.3 T0 3.1023-3.253 10.00 1.00 1 :: 52.2. 23 :: 1. Table 1: Turbine-specific 3-year mean values for 200 Vestas V1-2.0 wind turbines at 0 m. Generation values are provided in terms of energy and capacity factor. (continued on next page) 31
............................................................................................. Page...... 3... of... 3......... Appendix Turbine Means ind Air Gross ake et ID Latitude Longitude levation peed Density Generation Loss Generation (degrees) (degrees) (m) ( m s ) ( kg ) m 3 (Mh :: %) (%) (Mh :: %) T0 3.1320-3.2 10.2 1.000 5 :: 5. 1.5 331 :: 1. T0 3.132-3.13 1.5 0.3 :: 55.. 0 ::. T0 3.15-3.22 1.1 1.003 2 :: 53. 1. 20 :: 1.5 T0 3.153-3.52 2.32 0. 3 :: 55.0 2.5 5 :: 2. T2 3.1-3. 120.0 1.00 31 :: 53.2 3. 31 :: 1. T3 3.115-3.330 10.5 1.00 0 :: 51..5 1 :: 1.0 T 3.15-3.21 10.05 1.00 2 :: 52. 3.3 25 :: 1. T 3.1550-3.30 111.0 1.00 230 :: 52. 3.3 21 :: 1.3 T 3.133-3.1 11.0 1.00 2 :: 52. 2.1 12 :: 1.0 T1 3.1151-3.335 13.1 1.000 0 :: 53..0 25 :: 2. T111 3.1153-3.50 11.1 1.000 1 :: 53. 5.5 5 :: 3.1 T112 3.12-3.3 1.1 1.000 31 :: 53. 5.1 525 :: 2. T113 3.2201-3.55 10.12 1.00 30 :: 53.1 2. 253 :: 1. T11 3.15-3.31 1.2 0. 5 :: 5. 0. 2 :: 1.5 T115 3.12035-3.355 152.0 1.003 25 :: 53.0. 31 :: 2.1 T11 3.1322-3.035 10.12 1.002 35 :: 53. 3.5 30 :: 2.0 T11 3.21-3.3 155.1 1.003 0 :: 53. 2.3 30 :: 1. T11 3.135-3.0 15.13 1.002 3 :: 53.5 2.1 2 :: 1.5 T121 3.1210-3.352 1. 0.1 :: 5.2 3.2 5 :: 3. T122 3.13-3.13 1.21 1.001 51 :: 5.3 0. 21 :: 1.5 T123 3.1213-3.230 103.5 1.00 05 :: 51. 5. 2 :: 1.5 T12 3.1135-3.520 121. 1.00 :: 52.0. 2 :: 1.5 T125 3.13-3.0 1.2 0. 5 :: 5. 2. 2 :: 2. T12 3.052 -.030 120. 0.5 01 :: 55. 3. 0 ::.0 T12 3.12253-3.3 10.55 0. 1 :: 5. 2. 0 ::.0 T12 3.023 -.0155 12.51 0.5 01 :: 5.5.0 05 :: 5. T12 3.1202-3.5 1.51 0.1 :: 5..1 00 ::.5 T130 3.1 -.031 122.5 0.5 :: 5.. 03 ::.0 T131 3.002 -.020 132. 0. 33 :: 5.1 5. :: 5.0 T132 3.122-3.23 1.0 0.0 :: 5.0.0 2 ::. T133 3.011 -.0 12.52 0.5 :: 5.5. 112 ::.3 T13 3.30 -.0230 11. 0. 55 :: 5.2. 3 ::. T135 3.011 -.002 103.3 0. 3 :: 55.. 2 ::.3 T13 3.021 -.025 120.51 0.5 :: 5.5 3.5 52 ::.2 T13 3.053 -.022 112.3 0. :: 55. 3. 1 ::.0 T13 3.1201-3.5 1.50 0.0 5 :: 5.3 3.1 05 :: 3. T13 3.125-3.2 100.5 0. :: 5. 3. 15 ::. T10 3.1213-3.50 15.5 0.0 :: 5..1 ::. T11 3.115 -.010 11. 0. 5 :: 5.2 5.0 50 ::. T12 3.1202-3.01 1. 0.0 :: 55. 3. 5 :: 3. T13 3.1222-3.50 11.1 0.1 000 :: 5.0.3 :: 5.1 T1 3.05 -.01 113.5 0. 0 :: 55. 3.5 00 :: 3. T15 3.12-3.35 15.5 0. 0 :: 5.5 1. 33 :: 3.5 T1 3.12302-3.3 1.5 0. 5 :: 5. 2. 35 ::.1 T1 3.055 -.0213 111.0 0. 20 :: 55.. 22 ::.0 T1 3.02 -.0222 115.53 0. :: 5.5.3 3 ::. Table 1: Turbine-specific 3-year mean values for 200 Vestas V1-2.0 wind turbines at 0 m. Generation values are provided in terms of energy and capacity factor. (continued on next page) 32
............................................................................................. Page...... 35... of... 3......... Appendix Turbine Means ind Air Gross ake et ID Latitude Longitude levation peed Density Generation Loss Generation (degrees) (degrees) (m) ( m s ) ( kg ) m 3 (Mh :: %) (%) (Mh :: %) T1 3.3-3. 1.3 0.0 1 :: 55.. 01 :: 3. T150 3.052 -.0315 12. 0.5 1 :: 5.0.2 5 ::.2 T151 3.1201-3.3 13. 0. 25 :: 5.0 3.1 5 :: 3. T152 3.0301 -.00252 1.3 0. 1 :: 55.. 2 ::.1 T153 3.12213 -.00 10. 0. 12 :: 5.0. 03 ::.5 T15 3.1253 -.002 105.5 0. 5 :: 5..3 5 ::. T155 3.0515 -.001 102. 0. 3 :: 5.3 3. 5 ::.2 T15 3.03 -.01232 105. 0. :: 5.2.1 5 ::.3 T15 3.1221-3.2 1.5 0. :: 5. 2. ::.2 T15 3.1153 -.0112 11.1 0. 50 :: 55. 3. 52 :: 3. T15 3.00-3. 11.5 0. :: 5.0 3.3 3 :: 3. T10 3.050 -.02 115.3 0. 53 :: 55. 3. :: 3. T11 3.121 -.000 10. 0. :: 5.2 1. 52 :: 3.3 T12 3.05531 -.032 132.2 0. 3 :: 55.5. 00 :: 5.1 T13 3.11255 -.0130 11.50 0. 1 :: 5.2. 12 ::. T1 3.053 -.050 105.1 0. 33 :: 55.5 5. 0 ::.5 T15 3.05-3.3 1.3 0. :: 55..3 25 ::.1 T1 3.03 -.02 11.3 0. 1 :: 55.2. 2 :: 3. T1 3.002-3..3 0. 03 :: 55.3. 0 ::.0 T1 3.05-3.3 1.3 0. 3 :: 55.2. 5 :: 3. T1 3.01 -.01 10. 0. :: 5.0 3.2 :: 3. T10 3.00 -.0323 11.35 0. 13 :: 5.. ::. T11 3.00-3. 12.0 0. 5 :: 55. 2. 52 :: 3.2 T12 3.0 -.03152 123.51 0.5 2 :: 5..3 12 ::. T1 3.21 -.000 15.3 0. 0 :: 55. 1. 5 :: 2. T15 3.015 -.0352 123.32 0.5 5 :: 5..0 2 ::. T1 3. -3. 1.3 0. :: 55.3 3.0 5 :: 3.2 T1 3. -3.5112 11.3 0.2 :: 55.1. 01 :: 3. T1 3.000 -.0223 1.3 0. 5 :: 55.. 3 ::.3 T1 3.122-3.33 1. 0.1 5 :: 5.2. 1 ::. T 3.05-3.1 1.3 0. 3 :: 55.0. 3 :: 3. T11 3.155-3.250 5.2 0. 05 :: 5. 3.1 50 :: 2. T12 3.11-3.3 1.21 1.000 3 :: 53. 2. 350 :: 1. T13 3.113-3.225 1.1 1.001 1 :: 53. 3.2 3 :: 2.0 T1 3.1-3.23 11.0 1.00 20 :: 53.0 3. 31 :: 1. T15 3.11-3.01 15.20 1.002 :: 5.1 1.1 23 :: 1.5 T1 3.13-3.1 15.2 1.002 52 :: 5. 1. 33 :: 1. T1 3.205-3.202 10.1 1.001 332 :: 53.2.3 3 :: 2.2 T1 3.213-3. 1.13 1.00 31 :: 53.2. 05 :: 2.2 T10 3.1315-3.23 1.31 0.3 2 :: 5. 2. 5 :: 2. T11 3.212-3.10 12.1 1.002 30 :: 53.1 3. 33 :: 1. T12 3.235-3.5 12.0 1.00 23 :: 52..1 31 :: 1. T1 3.0 -.0020 13.0 0. 53 :: 55. 3.5 52 :: 3. T15 3.000-3.1 1.0 0. 55 :: 55. 1. 511 :: 2. T1 3.113-3.01 1.3 0. 5 :: 55.1 3.0 5 :: 3.0 T1 3.00 -.03250 123. 0.5 23 :: 5.0.0 2 ::.2 Table 1: Turbine-specific 3-year mean values for 200 Vestas V1-2.0 wind turbines at 0 m. Generation values are provided in terms of energy and capacity factor. (continued on next page) 33
............................................................................................. Page...... 3... of... 3......... Appendix Turbine Means ind Air Gross ake et ID Latitude Longitude levation peed Density Generation Loss Generation (degrees) (degrees) (m) ( m s ) ( kg ) m 3 (Mh :: %) (%) (Mh :: %) T1 3.0-3.215 12.35 0. 5 :: 55.2 2.5 520 :: 2. T1 3.00 -.031 12.3 0.5 0 :: 55.. 53 ::.2 T200 3.0311-3.2 1.35 0. 0 :: 55.2 2.5 515 :: 2. T201 3.151-3.211 1.1 1.00 0 :: 5.0 1.5 2 :: 1. T203 3.10-3.501 135.12 1.005 3 :: 53. 2.5 2 :: 1. T20 3.1352-3.051 1.25 0. 55 :: 5. 2.5 11 :: 2.3 T211 3.1225-3.05 1.0 1.003 2 :: 52. 2. 23 :: 1.3 T212 3.1001-3.335 1.05 1.003 21 :: 52. 2.0 1 :: 1.0 T21 3.10-3.53 13.0 1.00 2 :: 53.0 2.1 200 :: 1.1 T21 3.150-3.3 1.2 0. 5 :: 5. 1.1 2 :: 1. T21 3.15113-3.330 1.2 1.000 52 :: 5. 0. 2 :: 1.5 T21 3.1512-3.225 15.21 1.001 50 :: 5.2 1.0 23 :: 1.5 T220 3.1-3.032 10.1 1.002 53 :: 53. 2.3 3 :: 1. T221 3.11-3.2 15.1 1.002 52 :: 53. 0. 23 :: 1.3 T222 3.12-3.13 150.1 1.003 35 :: 53. 0.3 1 :: 0. T223 3.12-3.350 1.15 1.003 23 :: 53. 1.1 22 :: 1.2 T22 3.15-3. 1.1 1.00 0 :: 53. 1.2 21 :: 1.2 T225 3.112-3.3 10.13 1.00 32 :: 53. 1.3 220 :: 1.2 T22 3.130-3.553 123.01 1.00 1 :: 52. 3.3 21 :: 1.2 T22 3.11-3.55 13.1 1.002 :: 53. 2. 350 :: 1. T22 3.15-3. 135.15 1.005 12 :: 53. 2. 32 :: 1. T20 3.12-3.35 115.0 1.00 2 :: 53.0 3.0 22 :: 1.5 T25 3.21-3.22 102.0 1.00 21 :: 52. 3. 255 :: 1. T2 3.1152-3.1 112. 1.00 00 :: 51..0 1 :: 0. T250 3.1-3.2 155.20 1.003 :: 5.1 1. 30 :: 1. T251 3.10-3. 1.0 0. 21 :: 52. 3.0 2 :: 1.1 Table 1: Turbine-specific 3-year mean values for 200 Vestas V1-2.0 wind turbines at 0 m. Generation values are provided in terms of energy and capacity factor. ID et P50 et P5 et P0 et P5 et P (Mh :: %) (Mh :: %) (Mh :: %) (Mh :: %) (Mh :: %) T001 33 :: 1. :: 3. :: 3.1 :: 3.0 132 :: 35.0 T002 35 :: 2.0 011 :: 0.0 00 :: 3.2 513 :: 3.2 13 :: 35.2 T003 33 ::. 2 :: 2. 03 :: 0.3 5 :: 3.0 35 :: 3. T00 :: 2. 13 :: 0. 23 :: 3. 35 :: 3. 23 :: 35. T005 2 :: 1. 1 :: 3. 50 :: 3. :: 3. 150 :: 35.1 T00 23 :: 1.5 31 :: 3.5 1 :: 3. 2 :: 3. 0 :: 3. T00 2 :: 1. 2 :: 3. :: 3.0 2 :: 3.0 11 :: 35.1 T00 3 :: 1. :: 3. 1 :: 3.1 2 :: 3.0 13 :: 35.0 T00 05 :: 3. 1 :: 0. :: 3. 530 :: 3.2 05 :: 3. T0 5 :: 3.1 0 :: 0.5 1 :: 3.2 :: 3. 51 :: 3.2 T011 32 :: 2.0 02 :: 0.1 2 :: 3.3 53 :: 3.3 203 :: 35. T012 5 :: 3. 22 :: 1. 1 :: 3.5 11 :: 3.3 323 :: 3.1 T013 2 :: 1.3 1 :: 3. 1 :: 3. 3 :: 3. 0 :: 3. T01 353 :: 1. 020 :: 0.0 1 :: 3.3 53 :: 3.3 202 :: 35. Table 15: Turbine-specific 20-year generation probability of exceedance values (P-values) for 200 Vestas V1-2.0 wind turbines at 0 m. (continued on next page) 3
............................................................................................. Page...... 3... of... 3......... Appendix Turbine Means ID et P50 et P5 et P0 et P5 et P (Mh :: %) (Mh :: %) (Mh :: %) (Mh :: %) (Mh :: %) T015 5 ::.3 3 :: 2.1 0 :: 0.2 5 :: 3.0 :: 3. T01 20 :: 1.5 52 :: 3. 5 :: 3.0 :: 3.0 1 :: 35.1 T01 353 :: 1. 020 :: 0.0 20 :: 3.3 51 :: 3.3 20 :: 35. T020 31 :: 1. 2 :: 3. 00 :: 3.2 525 :: 3.2 1 :: 35.3 T021 2 :: 1. 5 :: 3. 5 :: 3.1 502 :: 3.1 1 :: 35.2 T022 53 ::. 51 :: 2.5 0 :: 0. 1 :: 3.2 :: 3. T023 323 :: 1. :: 3. 0 :: 3.3 533 :: 3.3 20 :: 35. T02 :: 2. 12 :: 0. 22 :: 3. 0 :: 3. 2 :: 35. T02 20 :: 1.5 51 :: 3. 55 :: 3.0 :: 3. 15 :: 35.1 T02 3 :: 2.0 035 :: 0.1 35 :: 3. 555 :: 3. 21 :: 35.5 T02 35 :: 2.1 03 :: 0.2 3 :: 3. 55 :: 3. 21 :: 35.5 T02 2 :: 1. 5 :: 3. 5 :: 3.0 0 :: 3.0 15 :: 35.1 T030 1 :: 1.0 5 :: 3.2 50 :: 3.5 33 :: 3.5 02 :: 3. T031 32 :: 2. 02 :: 0.5 :: 3. 0 :: 3. 21 :: 35. T032 35 :: 2.0 031 :: 0.1 3 :: 3. 50 :: 3. 22 :: 35.5 T033 33 :: 1. :: 3. :: 3.1 0 :: 3.0 10 :: 35.0 T03 1 :: 2.3 05 :: 0. :: 3. 0 :: 3. 21 :: 35. T035 33 :: 1. :: 3. 2 :: 3.2 50 :: 3.1 15 :: 35.2 T03 2 :: 2. 02 :: 0.5 0 :: 3. 0 :: 3. 21 :: 35. T03 35 :: 2.0 032 :: 0.1 0 :: 3. 5 :: 3. 23 :: 35. T03 2 :: 1. 1 :: 3. :: 3.0 0 :: 3.0 10 :: 35.1 T03 21 :: 1. :: 3. 0 :: 3.1 50 :: 3.1 13 :: 35.3 T00 :: 2. 1 :: 0. 3 :: 3.0 51 :: 3. 301 :: 35. T01 35 :: 2.0 0 :: 0.2 :: 3. 5 :: 3. 20 :: 35. T02 30 :: 2.0 032 :: 0.1 3 :: 3. 51 :: 3. 230 :: 35.5 T03 35 :: 2.1 0 :: 0.2 5 :: 3.5 51 :: 3.5 252 :: 35. T0 3 ::.3 3 :: 2.0 013 :: 0.0 01 :: 3. 02 :: 3.5 T05 51 :: 3.2 1 :: 1.1 53 :: 3.1 :: 3. 25 :: 35. T0 555 :: 3.1 21 :: 1.1 0 :: 3. 23 :: 3.3 3 :: 3. T0 1 :: 3.5 2 :: 1.5 52 :: 3. 3 :: 3. 0 :: 3. T0 51 :: 2. 12 :: 0. 1 :: 3.1 5 :: 3.1 32 :: 3.1 T0 3 :: 2.1 05 :: 0.3 3 :: 3. 55 :: 3. 252 :: 35. T050 50 :: 3. 2 :: 1. :: 3. :: 3. 2 :: 3. T051 5 :: 3. 2 :: 1. :: 3. :: 3. 1 :: 3. T052 53 :: 3.0 1 :: 1.0 :: 3.2 :: 3.1 322 :: 3.1 T053 55 :: 3.3 23 :: 1.3 1 :: 3.5 25 :: 3. 3 :: 3.3 T05 0 :: 3. 2 :: 1.3 23 :: 3.5 2 :: 3. 35 :: 3.3 T055 5 ::.2 3 :: 2.1 05 :: 0.2 55 :: 3.1 1 :: 3.0 T05 235 :: 1.3 :: 3. 23 :: 3.3 5 :: 3.5 30 :: 3.0 T05 33 :: 2.1 05 :: 0.2 1 :: 3. 55 :: 3. 25 :: 35. T05 :: 2. 122 :: 0. 11 :: 3. 2 :: 3. 25 :: 35. T05 2 :: 3. 21 :: 1.5 2 :: 3.5 1 :: 3.3 323 :: 3.1 T00 30 :: 2.2 0 :: 0.2 1 :: 3. 55 :: 3. 212 :: 35. T01 15 :: 2.3 0 :: 0. :: 3. 1 :: 3. 2 :: 35. T02 32 :: 1. :: 3. 5 :: 3.0 :: 3. 1 :: 3. T03 32 :: 1. 3 :: 3. 53 :: 3. 1 :: 3. 2 :: 3. T05 20 :: 3.5 25 :: 1. :: 3. 55 :: 3.5 3 :: 3.5 T0 335 :: 1. 00 :: 0.0 13 :: 3.3 53 :: 3.3 205 :: 35. Table 15: Turbine-specific 20-year generation probability of exceedance values (P-values) for 200 Vestas V1-2.0 wind turbines at 0 m. (continued on next page) 35
............................................................................................. Page...... 3... of... 3......... Appendix Turbine Means ID et P50 et P5 et P0 et P5 et P (Mh :: %) (Mh :: %) (Mh :: %) (Mh :: %) (Mh :: %) T0 :: 3. 25 :: 1. 11 :: 3. 03 :: 3.2 31 :: 3.0 T0 550 :: 3.1 15 :: 0. 3 :: 3.0 35 :: 3. 25 :: 35. T01 3 :: 1. 00 :: 0.0 :: 3.2 515 :: 3.2 10 :: 35.2 T02 351 :: 1. 01 :: 0.0 11 :: 3.3 530 :: 3.2 1 :: 35.3 T05 30 :: 1. :: 3. 2 :: 3.0 :: 3.0 13 :: 35.0 T0 12 :: 0. :: 3. :: 3.1 320 :: 3.1 5 :: 3.1 T0 23 :: 1. 0 :: 3. :: 3.1 505 :: 3.1 1 :: 35.2 T0 25 :: 1. 1 :: 3. 0 :: 3. 2 :: 3. 02 :: 3. T00 3 :: 3. 25 :: 1. 31 :: 3.5 31 :: 3. 355 :: 3.3 T01 2 :: 1. 5 :: 3. 3 :: 3.0 :: 3.0 153 :: 35.1 T02 300 :: 1. :: 3. 0 :: 3.2 51 :: 3.2 12 :: 35.3 T03 25 :: 3.5 20 :: 1. 32 :: 3.5 35 :: 3. 3 :: 3.3 T0 51 :: 3.0 1 :: 0. 32 :: 3.0 31 :: 3. 253 :: 35. T0 50 :: 2. 10 :: 0. 0 :: 3. :: 3. 23 :: 35. T0 30 :: 1. :: 3. 2 :: 3.0 :: 3.0 135 :: 35.0 T00 1 :: 1.1 5 :: 3.1 5 :: 3.3 33 :: 3.3 01 :: 3.3 T01 135 :: 0. :: 3. :: 3.0 303 :: 3.0 55 :: 3.0 T02 2 :: 1. 5 :: 3. 1 :: 3.0 :: 3.0 151 :: 35.1 T03 2 :: 1.3 3 :: 3.3 5 :: 3.5 3 :: 3. 032 :: 3. T0 23 :: 1. 1 :: 3. 00 :: 3. 12 :: 3. 00 :: 3. T0 331 :: 1. :: 3. :: 3.2 51 :: 3.2 11 :: 35.3 T0 0 ::. 0 :: 2.3 0 :: 0.3 5 :: 3.1 3 :: 3. T0 20 :: 1.5 5 :: 3. 0 :: 3.0 :: 3.1 12 :: 35.2 T0 5 :: 2. 13 :: 0. 35 :: 3.0 5 :: 3.0 313 :: 3.0 T2 31 :: 1. :: 3. 1 :: 3.1 :: 3.0 1 :: 35.0 T3 1 :: 1.0 :: 3.1 53 :: 3.3 3 :: 3.2 5 :: 3.2 T 25 :: 1. 12 :: 3. 01 :: 3. 15 :: 3. 0 :: 3. T 21 :: 1.3 :: 3.3 5 :: 3. 0 :: 3.5 05 :: 3.5 T 12 :: 1.0 :: 3.2 5 :: 3. 1 :: 3. 05 :: 3. T1 25 :: 2. 0 :: 0. :: 3. 50 :: 3.5 230 :: 35.5 T111 5 :: 3.1 2 :: 1.1 3 :: 3.3 03 :: 3.2 3 :: 3.2 T112 525 :: 2. 13 :: 0. 5 :: 3.1 :: 3.0 311 :: 3.0 T113 253 :: 1. 22 :: 3.5 23 :: 3. 5 :: 3. 1 :: 3. T11 2 :: 1.5 :: 3. 52 :: 3. :: 3. 1 :: 35.1 T115 31 :: 2.1 052 :: 0.2 5 :: 3.5 5 :: 3.5 2 :: 35. T11 30 :: 2.0 05 :: 0.5 :: 3.1 :: 3.2 21 :: 3. T11 30 :: 1. :: 3. :: 3.1 500 :: 3.1 1 :: 35.2 T11 2 :: 1.5 01 :: 0.0 :: 3. :: 3. 3 :: 3. T121 5 :: 3. 25 :: 1. 3 :: 3. 1 :: 3.3 31 :: 3.0 T122 21 :: 1.5 :: 3. 50 :: 3. :: 3. 1 :: 35.0 T123 2 :: 1.5 23 :: 3.5 0 :: 3. 13 :: 3. 05 :: 3.5 T12 2 :: 1.5 22 :: 3.5 11 :: 3. 25 :: 3. 05 :: 3. T125 2 :: 2. 0 :: 0.5 :: 3. 02 :: 3. 25 :: 35. T12 0 ::.0 202 :: 1.1 :: 3.5 :: 3. 52 :: 3.0 T12 0 ::.0 23 :: 1.5 1 :: 3.2 :: 3. 20 :: 35. T12 05 :: 5. 532 :: 3.0 02 :: 0.3 0 :: 3. 253 :: 35. T12 00 ::.5 3 :: 2.1 0 :: 0.0 :: 3. 3 :: 3.3 T130 03 ::.0 55 :: 3.1 2 :: 0.5 30 :: 3.0 31 :: 3.0 Table 15: Turbine-specific 20-year generation probability of exceedance values (P-values) for 200 Vestas V1-2.0 wind turbines at 0 m. (continued on next page) 3
............................................................................................. Page...... 3... of... 3......... Appendix Turbine Means ID et P50 et P5 et P0 et P5 et P (Mh :: %) (Mh :: %) (Mh :: %) (Mh :: %) (Mh :: %) T131 :: 5.0 30 :: 2.0 :: 3.3 0 :: 3. 0 :: 3. T132 2 ::. 5 :: 2.5 00 :: 0.3 30 :: 3.0 3 :: 3.5 T133 112 ::.3 5 :: 3.3 11 :: 0. 35 :: 3.0 30 :: 3.0 T13 3 ::. 355 :: 2.0 1 :: 3. 53 :: 3. 10 :: 35.1 T135 2 ::.3 23 :: 1.5 32 :: 3.0 5 :: 3.5 0 :: 3. T13 52 ::.2 25 :: 1. 12 :: 3. 55 :: 3.3 05 :: 3.5 T13 1 ::.0 22 :: 1.2 :: 3. 52 :: 3.2 033 :: 3. T13 05 :: 3. 2 :: 1.5 05 :: 3. :: 3.1 253 :: 35. T13 15 ::. 33 :: 2.0 5 :: 3. 13 :: 3.3 25 :: 35. T10 ::. :: 2.5 03 :: 0.3 35 :: 3.0 0 :: 3.5 T11 50 ::. 3 :: 2.1 5 :: 3. 00 :: 3.2 22 :: 35.5 T12 5 :: 3. 252 :: 1. 2 :: 3.2 :: 3. 21 :: 35.5 T13 :: 5.1 1 :: 2. :: 0.5 :: 3.2 5 :: 3. T1 00 :: 3. 22 :: 1.2 05 :: 3. 552 :: 3. 0 :: 3. T15 33 :: 3.5 15 :: 1.0 01 :: 3. 55 :: 3. 123 :: 3. T1 35 ::.1 2 :: 1. :: 3.3 0 :: 3.0 215 :: 35. T1 22 ::.0 223 :: 1.2 3 :: 3. 50 :: 3.1 5 :: 3.2 T1 3 ::. 355 :: 2.0 21 :: 3.5 1 :: 3.0 13 :: 35.2 T1 01 :: 3. 2 :: 1.5 :: 3.2 :: 3. 20 :: 35. T150 5 ::.2 233 :: 1.3 3 :: 3. :: 3.1 50 :: 3.1 T151 5 :: 3. 2 :: 1.3 :: 3.2 3 :: 3. 203 :: 35. T152 2 ::.1 21 :: 1.3 0 :: 3. 5 :: 3.3 05 :: 3. T153 03 ::.5 30 :: 1. 2 :: 3.5 :: 3.1 20 :: 35. T15 5 ::. 3 :: 2.2 5 :: 3. 3 :: 3. 22 :: 35. T155 5 ::.2 21 :: 1.5 3 :: 3.0 5 :: 3. :: 3. T15 5 ::.3 2 :: 1. 2 :: 3.1 03 :: 3. 11 :: 3. T15 ::.2 3 :: 1. 1 :: 3.5 :: 3.1 2 :: 35. T15 52 :: 3. 10 :: 1.0 :: 3. 525 :: 3.2 05 :: 3. T15 3 :: 3. 21 :: 1.2 0 :: 3. 52 :: 3. 2 :: 3. T10 :: 3. 1 :: 0. 1 :: 3.3 :: 3. 51 :: 33. T11 52 :: 3.3 15 :: 0. 2 :: 3.5 502 :: 3.1 050 :: 3.5 T12 00 :: 5.1 31 :: 2.0 5 :: 3.3 :: 3. 05 :: 3. T13 12 ::. 33 :: 1. 0 :: 3. 5 :: 3.0 13 :: 35.2 T1 0 ::.5 30 :: 1. 2 :: 3.1 55 :: 3. 03 :: 3. T15 25 ::.1 2 :: 1.3 15 :: 3. 55 :: 3. 03 :: 3. T1 2 :: 3. 12 :: 0. 13 :: 3.3 3 :: 3. 52 :: 33. T1 0 ::.0 23 :: 1.3 1 :: 3. 55 :: 3. 02 :: 3. T1 5 :: 3. 1 :: 1.0 :: 3. 513 :: 3.1 03 :: 3. T1 :: 3. 1 :: 1.0 51 :: 3.5 2 :: 3.0 00 :: 3.3 T10 ::. 2 :: 1. :: 3. 51 :: 3.2 51 :: 3.2 T11 52 :: 3.2 12 :: 0. 1 :: 3.3 :: 3. 01 :: 3.3 T12 12 ::. 3 :: 1. 5 :: 3.1 5 :: 3. 01 :: 3. T1 5 :: 2. 032 :: 0.1 33 :: 3. 3 :: 3.5 5 :: 33. T15 2 ::. 30 :: 1. 2 :: 3.1 5 :: 3.5 03 :: 3. T1 5 :: 3.2 130 :: 0. 31 :: 3. 2 :: 3.0 0 :: 3.5 T1 01 :: 3. 2 :: 1. 13 :: 3. 0 :: 3.2 21 :: 35. T1 3 ::.3 25 :: 1. :: 3.1 5 :: 3. 01 :: 3. T1 1 ::. 0 :: 2.3 03 :: 0.1 1 :: 3. 0 :: 3.5 Table 15: Turbine-specific 20-year generation probability of exceedance values (P-values) for 200 Vestas V1-2.0 wind turbines at 0 m. (continued on next page) 3
............................................................................................. Page...... 0... of... 3......... Appendix Turbine Means ID et P50 et P5 et P0 et P5 et P (Mh :: %) (Mh :: %) (Mh :: %) (Mh :: %) (Mh :: %) T 3 :: 3. 10 :: 0. :: 3.5 :: 3.0 011 :: 3.3 T11 50 :: 2. 15 :: 0. 5 :: 3.1 5 :: 3.1 331 :: 3.1 T12 350 :: 1. 02 :: 0.1 3 :: 3. 50 :: 3. 232 :: 35.5 T13 3 :: 2.0 03 :: 0.2 50 :: 3.5 55 :: 3.5 2 :: 35. T1 31 :: 1. 002 :: 3. :: 3.2 515 :: 3.2 13 :: 35.2 T15 23 :: 1.5 53 :: 3. 5 :: 3.0 2 :: 3.0 1 :: 35.2 T1 33 :: 1. 011 :: 0.0 21 :: 3.3 5 :: 3.3 221 :: 35.5 T1 3 :: 2.2 03 :: 0.3 :: 3. 55 :: 3. 2 :: 35. T1 05 :: 2.2 0 :: 0.3 :: 3. 52 :: 3.5 21 :: 35. T10 5 :: 2. 13 :: 0. :: 3. 53 :: 3. 213 :: 35. T11 33 :: 1. 005 :: 0.0 05 :: 3.2 52 :: 3.2 1 :: 35.3 T12 31 :: 1. 5 :: 3. :: 3.0 3 :: 3.0 13 :: 35.0 T1 52 :: 3. 1 :: 1.0 1 :: 3. 521 :: 3.2 053 :: 3.5 T15 511 :: 2. 00 :: 0.3 5 :: 3.0 11 :: 3. 555 :: 3.0 T1 5 :: 3.0 1 :: 0. 1 :: 3.3 5 :: 3.0 0 :: 3.5 T1 2 ::.2 20 :: 1.3 :: 3. 51 :: 3.2 00 :: 3.3 T1 520 :: 2. 05 :: 0.3 5 :: 3.0 11 :: 3. 551 :: 33. T1 53 ::.2 25 :: 1.3 :: 3. 51 :: 3.2 003 :: 3.2 T200 515 :: 2. 05 :: 0.2 3 :: 3. 3 :: 3.5 533 :: 33. T201 2 :: 1. 1 :: 3. :: 3.1 505 :: 3.1 1 :: 35.2 T203 2 :: 1. 0 :: 3. :: 3.1 500 :: 3.1 10 :: 35.2 T20 11 :: 2.3 0 :: 0.3 0 :: 3. 55 :: 3.5 22 :: 35.5 T211 23 :: 1.3 1 :: 3. 2 :: 3. 53 :: 3. 12 :: 35.0 T212 1 :: 1.0 0 :: 3. 5 :: 3.0 503 :: 3.1 21 :: 35.5 T21 200 :: 1.1 :: 3.2 51 :: 3.5 0 :: 3.5 0 :: 3. T21 2 :: 1. 5 :: 3. :: 3.0 :: 3.0 1 :: 35.1 T21 2 :: 1.5 2 :: 3. 3 :: 3. 3 :: 3. 12 :: 3. T21 23 :: 1.5 :: 3. 51 :: 3. 5 :: 3. 1 :: 35.0 T220 3 :: 1. 01 :: 0.0 1 :: 3.3 51 :: 3.3 20 :: 35. T221 23 :: 1.3 0 :: 3. 1 :: 3. 3 :: 3. :: 3. T222 1 :: 0. :: 3.1 555 :: 3. 3 :: 3. 050 :: 3.5 T223 22 :: 1.2 :: 3.3 01 :: 3. 2 :: 3. 02 :: 3. T22 21 :: 1.2 :: 3.3 52 :: 3. 15 :: 3. 02 :: 3. T225 220 :: 1.2 0 :: 3.3 53 :: 3. 15 :: 3. 02 :: 3. T22 21 :: 1.2 5 :: 3.2 50 :: 3.5 3 :: 3. 0 :: 3.5 T22 350 :: 1. 023 :: 0.1 2 :: 3. 552 :: 3. 222 :: 35.5 T22 32 :: 1. 00 :: 0.0 0 :: 3.3 530 :: 3.2 1 :: 35.3 T20 22 :: 1.5 31 :: 3.5 2 :: 3. 1 :: 3. 0 :: 3. T25 255 :: 1. 0 :: 3. 53 :: 3. 05 :: 3.5 053 :: 3.5 T2 1 :: 0. 05 :: 3. :: 3.1 312 :: 3.0 55 :: 3.0 T250 30 :: 1. :: 3. :: 3.1 :: 3.1 15 :: 35.2 T251 2 :: 1.1 :: 3.3 50 :: 3. 1 :: 3. 0 :: 3. Table 15: Turbine-specific 20-year generation probability of exceedance values (P-values) for 200 Vestas V1-2.0 wind turbines at 0 m. 3
............................................................................................. Page...... 1... of... 3......... Appendix Gross Long-term Variability 11 APPDIX GRO LOG-TRM VARIABILITY........................................................................................................................................ 11.1 ummary This section provides a retrospective analysis of the past 3 years of wind speed and power at the Rush Creek I location. These data were derived from a mesoscale umerical eather Prediction (P) model that has been statistically calibrated to match the observed data during the measurement period at each meteorological tower for which data were provided (Towers M2301 and M232). Due to long-term climate variability and/or change the historic distributions of wind and power capacity described here may not be indicative of future conditions. Based on the results of 3TIR s nergy Risk Framework, the last 3 years (January, 10 December, 2015) of data have been utilized for estimating the expected future generation at Rush Creek I. The average MO-corrected simulated wind speed at hub height (0 m) during the past 3 years of record (January, 10 December, 2015) across all 200 turbines is.2 m/s. The average MO-corrected simulated gross power capacity at hub height during the past 3 years across all 200 turbines is 5.5%. A map of average MO-corrected gross power capacity values across the Rush Creek I project area using the power curve for the Vestas V1-2.0 wind turbines is displayed in Power Capacity Maps. All power capacities presented in this section are gross power capacities. 3
............................................................................................. Page...... 2... of... 3......... Appendix Gross Long-term Variability 11.2 Power Capacity Maps This section contains a map of MO-corrected long-term mean gross power capacity values across the Rush Creek I project area for each turbine model and hub height. 11.2.1 Vestas V1-2.0 at 0 m 05' 00' 3 55' 3 50' 3 5' 3 0' 3 15' M232 3 15' 3 ' 3 ' M2301 3 05' 3 05' 05' 00' 3 55' 3 50' 3 5' 3 0' Project Turbines Met. Towers 52 5 V1 2.0 capacity factor (MO corrected) % Figure 1: 3-year mean capacity factor at 0 m. 0
............................................................................................. Page...... 3... of... 3......... Appendix Gross Long-term Variability 11.3 Model imulations By 3TIR The assessment of the wind resource across the Rush Creek I project presented in this section is based on 3 years of simulated data (January, 10 December, 2015) using a numerical weather prediction (P) model of the atmosphere. The 3-year simulated data set is constructed from two separate model runs: 1. a 1-year, 500 m resolution simulation (where the year of each calendar day is chosen sequentially from the last years (2005 201)), and 2. a 3-year continuous.5 km resolution simulation. The P model represents atmospheric processes in the boundary layer, including the roughness of the underlying terrain or water, stability within the boundary layer, heat and moisture fluxes into the atmosphere, wind shear, and turbulence within the boundary layer. The model outputs winds at fixed vertical levels, and there are such levels in the lowest 00 m of the atmosphere. To determine winds at specific hub heights, model data are interpolated between fixed vertical levels using power-law interpolation. This process essentially uses the standard power-law shear formula, where the shear exponent is determined exactly from the winds at the two bracketing levels, rather than assuming a fixed shear exponent. 3TIR configured the P model using nested grids to simulate the wind resource over the Rush Creek I region. ome details of the P configuration are shown below in Table 1. The extent of the coarsest grid was selected to capture the effect of synoptic weather events on the wind resource at the site, as well as to allow the model to develop regional, thermally-driven circulations. The increasingly fine 0.5 km, 13.5 km,.5 km, 1.5 km and 500 m grids were selected to model the effect of local terrain and local scale atmospheric circulations. After the P model simulations finished, a Time-Varying Microscale (TVM) model was employed to downscale the 500 m horizontal resolution P model output to the final 0 m horizontal resolution. All deliverables and model data shown in this section are derived from the 0 m resolution model grids. A map of the 0 m TVM grid is shown in Figure 15. Based on a comparison of the P output with observations from each meteorological tower for which data were provided (Towers M2301 and M232), a linear statistical model was constructed to remove the bias and adjust the variance of the raw P simulated winds. Parameter Value Mesoscale numerical weather prediction model RF Horizontal resolution of valid study area 500 m Final downscaled horizontal resolution 0 m umber of vertical levels 31 levation database 3 second RTM Vegetation database second A Globcover urface parameterization Monin-Obukhov similarity model Boundary layer parameterization YU model (MRF with entrainment) Land surface scheme -layer oah-land urface Model Table 1: umerical weather prediction model configuration 1
............................................................................................. Page......... of... 3......... Appendix Gross Long-term Variability ' 00' 3 50' 3 0' M232 3 ' M2301 3 ' 3 00' 3 00' ' 00' 3 50' 3 0' Figure 15: Map of the 0 m resolution P model domain. The bold red box marks the boundary of the valid study area. The yellow triangles denote locations of meteorological towers and white dots indicate wind turbines. 2