MIFACE INVESTIGATION: #02MI060

Similar documents
Chemical Hygiene Plan for Laboratories

Northwest Hydro Tech Session_2017

General. High Winds. High winds are a common hazard in the UAE.

MIFACE INVESTIGATION #06MI207

HAZARD COMMUNICATION PROGRAM

HAZARD COMMUNICATION PROGRAM

UNITED STATES DEPARTMENT OF LABOR MINE SAFETY AND HEALTH ADMINISTRATION Metal and Nonmetal Mine Safety and Health REPORT OF INVESTIGATION

Extension Safety Ladder with Outriggers

Hazard Communication Policy

LIGHTNING SAFETY #24 CONSTRUCTION SAFETY EDUCATION PROGRAM

Hazard Communication Program

Tornado Preparedness. Monthly Safety Meeting

RADIATION SAFETY GUIDELINES FOR NON-USERS

Hazard Communications

HAZARD COMMUNICATION SAFETY PROGRAM

Accident/Incident Report and Investigation Form

HAZARD COMMUNICATION PROGRAM

How Power is Restored After a Severe Storm. Presented by Stacy Shaw, Safety Director & Nolan Hartzler, GIS Mapping Technician

Hazard Communication

GUIDELINES FOR FILMING IN TOMBALL, TEXAS

MIFACE Investigation Report #10MI069

PROVINCIAL HEALTH AUTHORITIES OF ALBERTA ACT

Facilities Management

Marquette University Effective: 5/21/02 Hazard Communication Program Updated: 03/11/09 Revision No.: 1 Page: 1

EOSMS Guidelines Date: 01/16/2014 Page 1 of 5

15 TH ANNUAL ACI RISK MANAGEMENT CONFERENCE SESSION 1A

Department of Environmental Health and Safety Laboratory Decommissioning and Clearance

Good Spirit School Division Parents/Guardians

Laboratory Chemical Safety. Pathology Training

Bid Specifications Release Date: October 18, 2017 DESCRIPTION: Snow Plow Services

Safety Issue: Types of weather emergencies and natural. Weather Emergencies

A Unique, Educational SELL-OUT EVENT. September 15, 2018 Convention Center 10am-3pm at the Empire State Plaza 2018 EXHIBITOR INFORMATION

CITY OF TOMBALL PUBLIC POSTING. Driver/ Operator Hiring Announcement

C h a p t e r 5 : W o r k p l a c e H a z a r d o u s M a t e r i a l s I n f o r m a t i o n S y s t e m ( W H M I S )

HAZARD COMMUNICATION PROGRAM

Hazard Communication Program

UNIVERSITY OF HOUSTON ENVIRONMENTAL HEALTH AND & LIFE SAFETY POLICIES AND PROCEDURES I. PURPOSE

A regular meeting of the Village of Victor Planning Board was held on Wednesday, July 26, 2017, at the Village Hall, 60 East Main Street.

UNITED STATES DEPARTMENT OF LABOR MINE SAFETY AND HEALTH ADMINISTRATION Metal and Nonmetal Mine Safety and Health REPORT OF INVESTIGATION

AM 500A 500 WATT AM 1A 1 KILOWATT AM BROADCAST TRANSMITTERS. October, 1999 IM No

Chemical Safety as a Core ACS Value: Report on the 2018 Safety Summit

UNITED STATES DEPARTMENT OF LABOR MINE SAFETY AND HEALTH ADMINISTRATION Metal and Nonmetal Mine Safety and Health REPORT OF INVESTIGATION

REQUEST FOR PROPOSALS

CLEA# Approved Date: Feb Revision Date: Aug 02, May06, Mar08, Jan 09 New ( ) Amends ( ) Rescinds ( ) Pages:

LOS ANGELES UNIFIED SCHOOL DISTRICT REFERENCE GUIDE

PUBLIC EMPLOYEE HAZARDOUS CHEMICAL PROTECTION AND RIGHT TO KNOW ACT O.C.G.A

Group Exercise - Case Study: Day 2 - Accident & Incident Investigation

Responsibilities: Effective Date: November Revision Date: February 8, VP, Facilities and Construction Management. Issuing Authority:

Lamp and Control Panel (Lamp Panel)

Our Mission. Seeks to save lives and prevent injuries through developing advanced visible technologies

Acknowledgment of Aramco Asia. Supplier Code of Conduct

The information contained in this SOP is general in nature. Any YouTube videos included are as a compliment to the information presented.

Geneva College Hazard Communication Program Presentation

AS STANDARD

Making Decisions with Insulation

Inclement Weather Preparedness. Tornadoes and Severe Thunderstorms

SK Series BOX PLOW INSTALLATION & OWNER S MANUAL TABLE OF CONTENTS

Art, Science or Voodoo?

Service Call: Rotation Bearing Deflection Test. Dial Indicator with Magnetic Base Maintenance Manual for the Unit Being Tested

Requirements to perform accurate dielectric material analysis

Global Harmonization and Hazard Communication

SELF-AUDIT CHECKLIST

A.R.M. 52 PLOW With QUICK ATTACH MOUNTING SYSTEM MODEL NUMBER BLACK MODEL NUMBER GRAY. Owner s Manual

50 Gordon Drive, Rockland, Maine sherplows.com. STORM BOXX Snowplow. 10' and 12' Box Plow for Backhoe Loaders

Tornadoes Module 2. - Tornado Watch -

Quarries National Joint Advisory Committee (QNJAC) Occupational Health. Information Sheet 10. April Management of Asbestos on Site

Lab 1: Safety Lab; Introduction to Volumetric and Weighing Techniques

Steps to Reduce the Risk of Tornado Damage in Commercial Structures

IS YOUR BUSINESS PREPARED FOR A POWER OUTAGE?

CHEMICAL SAFETY TRAINING LEADER GUIDE. Chemical Safety Training Leader Workbook 1

Health, Safety, Security and Environment

SAMPLE PAGES. Hazard Communication Program. [Company name]

Compact Orifice FlowMeter

CONTACT SAFETY PROGRAM MAY 2006

HAZUS-MH: Earthquake Event Report

Individual Laboratory Safety & Chemical Hygiene Plan

PHA, MOC and Incident Investigation in Partnership: A Catalyst for Process Safety Excellence

Chemical Inventory. Each area must maintain a complete, accurate and up to date chemical inventory. The inventory should include: All Chemicals

POWER PUSHER Snowplow

HAZARD COMMUNICATION PROGRAM 2015 UPDATE GHS AWARENESS TRAINING CSULB COE

Demonstrate knowledge of a track warrant control (TWC) system

First Quarter OSHA Hazardous Chemical Labeling Requirements

STANDARD OPERATING PROCEDURES

ADMINISTRATION BUILDING

Initial Report. North Central Texas Initial Attack. Hildreth Road Dozer Accident. February 9, 2006

ER2 Short-head Electric Chain Hoist

Rimkus Consulting Group, Inc.

Application for Radioactive Material Use

3. Chemical Hygiene Plan: Laboratory Standard Operating Procedures. A. Laboratory Specific Information and Signatures

Risk Assessment and Management System (RAMS)

Storing, using and disposing of unsealed radioactive substances in a Type C Laboratory: Extract of regulatory requirements

Peterborough Distribution Inc Ashburnham Drive, PO Box 4125, Station Main Peterborough ON K9J 6Z5

Nuclear Science Merit Badge Workbook

How do I assess the current condition of the chemical inventory?

Summary of Wind Turbine Accident data to 30 September 2010

Severe Weather Policy (Snow & Ice) Seek Ye First the Kingdom of God...

CHEMICAL SAFETY. 2.1 DOE O 231.1, Environment, Safety, and Health Reporting

Survey of awareness about hazardous chemicals of residents living near chemical plants in South Korea

RENCO ELECTRONICS, INC.

Installation guide 862 MIT / MIR

Transcription:

MIFACE INVESTIGATION: #02MI060 SUBJECT: Millwright Dies from Fall Off Ladder Summary On June 12, 2002, a millwright installing new copper lines approximately 18 feet in the air was killed when he fell from his extension ladder. No one saw him fall. He had started work at approximately 7:00 a.m. and had been working about an hour when a nearby worker heard a noise. When the worker investigated, he found the victim on the floor of the plant next to his ladder. The victim s ladder was supported on the crossbeam of a movable hoist and not on the building I-beam that was nearer to the area where he would have been working. There was evidence that the ladder had been originally leaned against the I-beam and had slipped and fallen to the hoist crossbeam. The victim was lying perpendicular to the ladder on his right side with his back toward the ladder, facing away from the ladder. Emergency personnel indicated that he appeared to have fallen heavily on his right side, because he had multiple rib fractures on his right side as well as head injuries. It is possible that he was standing on his ladder with his back to it working on the copper piping. When the ladder slipped, he fell, he twisted to his right and fell onto his right side. RECOMMENDATIONS Figure 1 Employers should develop a written accident prevention plan that identifies and describes hazards that could be encountered in the worksite and how to recognize and avoid them. Securely fasten ladders to prevent them from slipping. Ensure workers are trained in the safe use of ladders and follow safe procedures.

INTRODUCTION On Wednesday, June 12, 2002, a 54-year old millwright was killed when he fell from a ladder he had been working from. He was installing new copper lines on a 22-foot plant ceiling. On June 13, 2002, MIFACE investigators were informed by the Michigan Occupational Safety and Health Act (MIOSHA) personnel who had received a report on their 24 hour-a-day hotline that a workrelated fatal injury had occurred on June 12, 2002. On July 11, 2002, the MIFACE researcher interviewed the Vice-President of the plant who was also the Technical Director. He accompanied the researcher into the plant, showed her the incident site and described the events on the day of the fatality. During the course of writing the report, the autopsy results and the MIOSHA citations were obtained. The MIOSHA investigation resulted in three citations being issued to the company: one citation for failing to provide a training program for employees using extension ladders; one for the ladder being unsecured; and one for failing to develop and present an accident prevention program. INVESTIGATION On Wednesday, June 12, 2002, a 54-year old millwright was installing new copper lines near a 22- foot plant ceiling for a company that manufactured lubricants and release agents for the die cast industry. The company had been in business for 44 years and employed nine people. The victim had been a millwright for over 30 years. He was working as a temporary employee at the time of the incident. He had done temporary jobs for the company in the past and had recently worked for another company in the neighborhood doing the same type of work. The victim started work at approximately 7:00 a.m. and had been working less than one hour when another employee working nearby heard a noise and went to investigate. He found the victim unconscious on the floor next to his ladder. The extension ladder was standing upright, leaning against a hoist crossbeam behind the area where the victim was working, not on the building I-beam closer to where he had placed his material. The container of material the victim had been using to connect the pipes was on the building I-beam (Figures 1 and 2). Figure 2 The ceiling height was 22 feet. The copper lines being installed were located at approximately 18 feet. No one saw how the victim had set up his equipment or saw him working on the lines. The worker who investigated the noise found the victim on his right side perpendicular to the ladder with his back toward the ladder. He was lying with his head toward the rear of the plant 2

and his feet toward the area where he was working. It appears unlikely that he moved after his fall, because the worker who investigated the noise was quite close to the area where he fell. Reconstruction of the probable scenario indicated that the ladder had been leaned against the I- beam and had slipped and fallen to the hoist crossbeam causing him to lose his balance and fall to the floor (Diagrams 1 & 2). Marks were apparent on the ladder that matched where it would have fallen to the hoist crossbeam in such a scenario. On the day of her visit, the MIFACE investigator was not able to examine the floor where the event occurred because containers were stored in the area. The extension ladder belonged to the victim and appeared to be in good condition (Figure 3). It was a fiberglass extension ladder with aluminum rungs. According to the Technical Director, the area around the ladder was clear at the time he was working there. However, on the nearby floor, there was evidence that the products of the manufacturing process, lubricants and die release compounds, had been absorbed into the flooring surface. The MIOSHA officer who investigated the fatality shortly after it occurred indicated in his report that a dark film of this product is on the ladder s safety feet, on the aluminum rungs of the ladder, and soles of shoes/boots worn in this area. Based on the position of the ladder and the position in which the victim was found, it is possible he was standing on the ladder with his back to it working on the piping in front of him. As the ladder slipped, he fell, twisted to the right and fell onto his right side. The emergency medical personnel indicated that it appeared that he had fallen heavily onto his right side, because he had multiple rib fractures on the right side as well as head injuries on the right. CAUSE OF DEATH Figure 3 The cause of death as stated on the death certificate was multiple injuries, multiple blunt injuries to the head and trunk consistent with a fall. The results of all toxicological tests were negative. RECOMMENDATIONS/DISCUSSION Employers should develop a written accident prevention plan that identifies and describes hazards that could be encountered in the worksite and how to recognize and avoid them. Although the workplace was an industrial site, the installation of the copper piping was construction work. The victim had done work at the site previously, but was not a full-time employee. The lubricants and die release products the company manufactures had been absorbed into the floor over the years. Instruction regarding this fact would have reminded the victim of the nature of the flooring and his footing. The soles of his shoes may have become slippery by having picked up the lubricants or die release products on the floor. The rungs of the ladder would also then have become slippery and could have caused him to lose his footing. 3

Securely fasten ladders to prevent them from slipping. Ladders should be lashed or otherwise securely attached to ensure they will not slip. Slip resistant feet are not an acceptable substitute for holding a ladder in place that is used upon slippery surfaces. Ensure workers are trained in the safe use of ladders and follow safe procedures. Reinforcement of safe ladder practices by means of an accident prevention plan and training would have addressed the following items. 1. Ensure ladders are secured where there is the possibility of a slippery surface. The top of the ladder was not secured. Although the ladder had slip-resistant feet, they are not an adequate substitute for holding a ladder in place on slippery surfaces. 2. Always face the ladder when ascending or descending. Although no one saw the victim fall, the position of the body suggests that he may have had his back to the ladder. 3. Remove any slippery material from the soles of shoes or rungs of the ladder before using the ladder. The product manufactured by the company was inherently slippery. It had been absorbed by the flooring over the years and may have caused the soles of the victim s shoes, the rungs of the ladder or his hands to become slippery. Diagram 1 Diagram 2 REFERENCES 1. Accident Prevention Manual for Business & Industry, Engineering and Technology, 11th Edition, National Safety Council, Chicago, 1997. 2. MDCIS Director s Office, Construction Safety Standards, Part 11. Fixed and Portable Ladders. 4

MIOSHA Standards cited in this report can be found at the Consumer and Industry Services, Bureau of Safety and Regulation Standards Division website at www.michigan.gov/cis. Follow the links Workplace Safety & Health then Standards & Legislation to locate and download MIOSHA Standards. The Standards can also be obtained for a fee by writing to the following address: Department of Consumer and Industry Services, MIOSHA Standards Division, P.O. Box 30643, Lansing, MI 48909-8143. MIOSHA phone number is (517) 322-1845. MIFACE (Michigan Fatality and Control Evaluation), Michigan State University (MSU) Occupational & Environmental Medicine, 117 West Fee Hall, East Lansing, Michigan 48824-1315. This information is for educational purposes only. This MIFACE report becomes public property upon publication and may be printed verbatim with credit to MSU. The author of this report is working under contract to MSU and is affiliated with Wayne State University. Reprinting cannot be used to endorse or advertise a commercial product or company. All rights reserved. MSU is an affirmative-action, equal opportunity employer. 2/20/03 5

MIFACE Investigation Report # 02 MI 060 Evaluation To improve the quality of the MIFACE program and our investigation reports, we would like to ask you a few questions regarding this report. Please rate the following on a scale of: Excellent Good Fair Poor 1 2 3 4 What was your general impression of this MIFACE investigation report? 1 2 3 4 Was the report Objective? 1 2 3 4 Clearly written? 1 2 3 4 Useful? 1 2 3 4 Were the recommendations Clearly written? 1 2 3 4 Practical? 1 2 3 4 Useful? 1 2 3 4 How will you use this report? (Check all that apply) Distribute to employees/family members Post on bulletin board Use in employee training File for future reference Will not use it Other (specify) Thank You! Please Return To: MIFACE Michigan State University 117 West Fee Hall East Lansing, MI 48824 FAX: 517-432-3606 If you would like to receive e-mail notifications of future MIFACE work-related fatality investigation report summaries, please complete the information below: Name: e-mail address: I would like to receive summaries for reports involving: Construction Manufacturing Agriculture All