STATUS OF THE VEPP-000 COLLIDER PROJECT Yu.M. Shatunov for the VEPP-000 Team Budker Institute of Nuclear Phsics, 630090, Novosibirsk, Russia Abstract The VEPP-000 collider which is now under construction in the Budker Institute will operate with round colliding beams at the energ of up to 1 GeV per beam. In this paper the current status of manufacturing, assembling and testing is reviewed. Results of beambeam simulation for round beams are given. INTRODUCTION A decision to upgrade the VEPP-M comple b replacing the eisting collider with a new one in order to improve the luminosit and at the same time increase the maimum attainable energ up to GeV will significantl broaden the potential of eperiments performed at the collider. The new project was given the name VEPP- 000 based on the center-of-mass energ and ear when the project has been approved. Figure 1 shows the laout of the VEPP-000 comple. It consists of.5 MeV linac, 50 MeV snchrotron, booster ring and the VEPP-000 storage ring. The booster can change polarit to store subsequentl electrons and positrons and is capable of accelerating beams up to the energ of 900 MeV. Above this level the energ of the collider will be ramped to the energ of eperiment. The injector is kept unchanged from the VEPP-M collider ecept the power suppl and control sstems. The design luminosit of VEPP-000 at 1 GeV is 1 s 3 1 cm. ROUND COLLIDING BEAMS CONCEPT The basic parameter of a collider is its luminosit L which in the case of short bunches is determined b the formula: πγ ξ ξ ε f σ 1 L = +, re σ where ξ, ξ are the space charge parameters whose maimum values are limited b beam-beam effects; ε is the horizontal emittance of the beams, σ, σ are their r.m.s. sizes at the interaction point (IP), and is the vertical beta-function at the IP; f is the frequenc of collisions at this IP, r e is the classical electron radius, γ is the relativistic factor. The space charge parameter per interaction is: ξ, Nre = πγ σ,, ( σ + σ ), where N is the number of particles in the opposite bunch. Colliding bunches with maimum values of ξ 0.05 and ξ 0. 0 have been eperimentall obtained at the VEPP-M collider [1]. Aiming at a ver high luminosit due to raising the ξ limits in the Novosibirsk Φ -factor project [,3], colliding beams with round transverse cross-sections were proposed (just round beams in what follows). During the last decade at BINP, this approach evolved into the concept of Round Colliding Beams (RCB) []. In the RCB case, the luminosit formula has the form: πγ ξ εf L =, and the space charge parameters are now the same in the two directions, so the horizontal parameter can be strongl enhanced. The evident advantage of round colliding beams is that with the fied particle densit, the tune shift from the opposite bunch becomes twice as small as the tune shift in the case of flat colliding beams. Besides, the linear beambeam tuneshift in the round beams becomes independent of the longitudinal position in the bunch, thereb weakening the action of snchrobetatron resonances. The main feature of the RCB is rotational smmetr of the kick from the round opposite beam; complemented with the X Y smmetr of the betatron transfer matri between the collisions, it results in an additional integral of motion M = ' ', i.e. the longitudinal component of particle's angular momentum is conserved. Thus, the transverse motion becomes equivalent to a onedimensional (1D) motion. Resulting elimination of all nonlinear betatron coupling resonances is of crucial importance, since the are believed to cause the beam lifetime degradation and blow-up. Figure 1. Laout of the VEPP-000 comple. r e
LATTICE OF VEPP-000 The round beam optics for a collider with small energ and two interaction points can be practicall realized using solenoids as the main focusing elements in eperimental straights. In this case the lattice consists of two smmetrical achromatic arcs with conventional optics, and solenoidal blocks on both sides of the IPs (Fig. ). Besides the focusing, each solenoid rotates the plane of betatron oscillations b π /. B switching the polarit of the blocks one can arrange various options: conventional flat beam, when the rotation over the IP is zero. round beam, when rotation over one turn is zero, but the - modes interchange between the arcs mobius ring with one-turn rotation equal to π. An essential advantage of the found optics is zero dispersion in the IRs, RF cavit, and injection straight sections. The chosen optics has another ver useful feature. Variation of the focusing strength of the solenoids changes and the beam emittance in inverse proportion at fied energ. Changing energ, we can squeeze, conserving the maimum beam size in the solenoids, thus giving a possibilit to tune optics for better performance. Apparentl, this feature provides the luminosit scaling at lower energies approimatel as γ (instead of γ for the option with fied (Fig. ). Figure. Practical realization of round beams. For the main operation mode with round beam the following conditions are fulfilled: Q = Q, ε = ε, =. The optical functions of the round beam lattice of VEPP-000 are presented in Figure 3. Figure 3. Lattice functions of VEPP-000 (half period). Figure. Scaling of the VEPP-000 luminosit with energ. The main parameters of the new collider are given in Table 1 Parameter Value Circumference.38m RF frequenc 17 MHz RF voltage 0.1MV Momentum compaction 0. 036 Snchrotron tune 0. 0035 Energ spread 6. Beam emittances (,) 1.9 7 m.19 Dimensionless damping decrements (,,z).19.83 Betatron tunes. 05,. 05 Betatron functions @ IP 0.1m Bunch population 11 1.0 Luminosit per IP 3 1 1.0 cm s Table 1. Main parameters of VEPP-000.
BEAM-BEAM SIMULATIONS The above arguments in favour of RCB have been checked out b computer simulations of the beam-beam effects in the VEPP-000 collider lattice [5,6]. Both weak-strong and strong-strong cases have been studied using two codes. The strong-strong code is the modified BBSS b K.Ohmi [7]. The weak-strong case has been addressed b means of Shatilov's LIFETRAC [8] and BBSS. The main results of the simulations are presented in Figs. 5-8. For the weak-strong case the emittance of weak beam is plotted against the beam-beam parameter (Figs. 5,6). One can see that the beam blow-up for round beam is rather moderate even at ξ = 0.. Taking into account the machine nonlinearities represented b setupoles does not change the beam behaviour ver much. The strong-strong calculation proves the advantage of the round beam and predicts the design luminosit of VEPP-000 to be achieved at ξ 0. 1 (Figs. 7,8). The simulations have also demonstrated stabilit of RCB against the ``flip-flop" effect, similarl to conclusions from simple flip-flop models [9]. Figure 7. Beam size and L vs. ξ (setupoles off ). Figure 8. Beam size and L vs. ξ (setupoles on ). Figure 5. Emittance of weak beam vs. ξ (setupoles off ). 1-LIFETRAC, -BBSS. ELEMENTS OF THE RING Magnets The lack of space for placing the new machine lead to demand on using of strong dipole magnets. For the energ of particles in the beam to be 1 GeV the field of a magnitude.38 T is needed. Such magnets have been designed, manufactured, tested and installed in the eperimental hall. Figures 9, show the view of the dipole and the ecitation curve. Figure 6. Emittance of weak beam vs. ξ (setupoles on ). 1-LIFETRAC, -BBSS Figure 9.. T dipole magnet.
Magnetic measurements confirmed the field calculation done b 3D code MERMAID. The measured field uniformit is of the order of at the top field level in the aperture ± 1.5cm. All quadrupole magnets have been produced. After magnetic measurements, some correction was required to improve the field qualit in the required aperture. This was done b adding facets. The chromaticit correction setupoles have been received from the machiner workshop recentl and undergo tests and measurements. Due to deficit of free space in the ring, all magnets have additional steering coils: dipoles and quadrupoles conatin dipole correctors, skew-quads are combined with setupoles. Figure. Ecitation curve for the dipole. (Units on the vertical ais Gs). Solenoids Each solenoidal block consists of a main solenoid which is longitudinall divided into two parts, and a compensating solenoid with reverse field to adjust longitudinal field integral and focussing (Fig. 11). Such a scheme gives an additional possibilit to control the value b feeding onl one half of the main solenoid at lower energies. Figure 11. View of the solenoid. A prototpe solenoid (a half of the main coil) has been manufactured and tested. The design field of 13T has been achieved and now the design is adopted and the coils are being produced. RF Sstem The accelerating field frequenc is 17MHz at the 1 th harmonic of the revolution frequenc. The normalconducting single mode RF cavit have been manufactured and is now under cold testing. Vacuum Sstem The high-vacuum sstem consists of 16 ports with iongetter pumps which are located at the edges of bending magnets vacuum chambers; of one ion-getter pump connected to the RF cavit; and of cropumps formed b cool solenoid surface. To prevent heating of the crosurface which is under. K b SR a perforated liner cooled with the liquid nitrogen is used. The liner ports should provide linear pumping rate of 5 l/s/cm for the nitrogen. Beam Injection The beams will be injected into the storage ring in horizontal plane into the long drift opposite to the RF cavit. The inflector plates are placed on the inner side of the vacuum chamber in the bending magnets at the ends of the drift. The advantage of such a scheme is independence of the injected beam trajector on the solenoids field. The HV pulse generator for the injection sstem with 50 kv pulse amplitude and duration of 0ns have been tested and is being prepared for installation. FUTURE POSITRON SOURCE The rate of particle losses in the VEPP-000 collider at 8 1 the design luminosit is estimated as s (beam life time 1.1 3 s ). The main sources are the Touschek effect, gas bremsstrahlung and single beam-beam bremsstrahlung. Eisting injector is capable of suppling the positrons at the rate which is one order of magnitude smaller than necessar. To provide the required amount of positrons a transfer channel from the VEPP-5 preinjector comple is being built. At the moment, one half of the tunnel is read. The channel lattice has been designed and manufacturing of the magnets is in preparation. SUMMARY Main magnetic elements of the VEPP-000 storage ring are read and the collider is being assembled. The superconducting solenoid prototpe has been tested and reached the design field. The RF sstem is under testing and will be read for installation soon. The power supplies are produced. The collider will start operation with eisting injector which will provide positrons at the rate sufficient to
31 1 maintain luminosit of cm s. The transfer channel from the new positron source is being built. Under favourable conditions we plan to have the first beam in VEPP-000 b the end of 00. REFERENCES [1] P.M.Ivanov et al., in: Proc. 3rd Advanced ICFA Beam Dnamics Workshop, Novosibirsk, (1989), p. 6. [] L.M.Barkov et al., in: Proc. 1th HEACC, Tsukuba (Japan), (1989), p.1385. [3] L.M.Barkov et al., in: Proc. PAC91, San~Francisco (1991), p.183 [] V.V. Danilov et al., in: Proc. EPAC'96, Barcelona (1996), p.119. [5] A.Valishev, E.Perevedentsev, K.Ohmi, in: Proc. PAC 003. [6] I.Koop et al., ICFA Beam Dnamics Newsletter No. 31, August 003, p.. [7] K.Ohmi, Phs. Rev. E 59, 787 (000) [8] D.Shatilov, Part. Accel. 5, 65 (1996) [9] A.V.Otboev and E.A.Perevedentsev, in: Proc. PAC99, New York (1999).