Identification The specification of C-Lube Linear ay is identified by the identification, which consists of a model code, a size, a part code, a material code, a preload symbol, a classification symbol, interchangeable code and supplemental codes. C-Lube Linear ay type : ide type : xample of identification specification Slide unit only C C T P S /U C-Lube Linear ay M lange type, mounting from bottom : M C-Lube Linear ay M lange type, mounting from bottom : M Track rail only L R0 B P S Set product C C R0 T P S /U lange type, : MT lange type, : MT on-interchangeable specification Set product C C R0 T P /U Block type, : MS Block type, : MD Length of slide unit code umber of slide unit Compact block type, : MS Length of track rail Part code C-Lube Linear ay MUL Miniature type : MUL 0 Material Preload Accuracy class Interchangeability Optional specification Material code Preload symbol Classification symbol code Supplemental code Applicable types and size are shown in Table. to. on the next page. Mode codes for ordering track rail only are shown in Table. Table codes for ordering track rail only Material code of track rail C-Lube Linear ay type Stainless steel LLB ide type Stainless steel LLB C-Lube Linear ay M Carbon steel L Stainless steel L C-Lube Linear ay M ( to C-Lube Linear ay M ( to Carbon steel Carbon steel L LB Stainless steel Stainless steel L L ote : Applicable material and code are shown in Table on page. (o symbol (o symbol (o symbol SL (o symbol SL (o symbol SL ote : In case ordering track rail only, model code is changed as shown below. Please Reler Table. Track rail of interchangeable code LL-B (x: LLRBPS Track rail of interchangeable code LL-B (x: LLRBPS Track rail of interchangeable M code L (x: LRPS Track rail of interchangeable M code L (x: LRBPS Length of slide unit Short : C (x: CCS : o symbol igh rigidity long : G (x: MGCR xtra igh rigidity long : L (x: MTLCR = 0.0kgf = 0.lbs. = 0.0inch

Identification Table. Types and sizes of C-Lube Linear ay Material Shape of the slide unit Length of the slide unit code type Short igh rigidity long C G Stainless steel Short C ide type igh rigidity long G Remark : marks indicates that interchangeable products are available. 0 Applicable types and size are shown in Table. to.. umber of slide unit Length of track rail Material Set product (with track rail Slide unit only ( series Track rail only Set product (with slide unit Slide unit only Track rail only ( series Carbon steel Stainless steel : C (x : MCR : C (x : MCS : o symbol : R (x:mcr : o symbol : R (x:lrs : o symbol : SL or an assembled set, indicate the of slide units assembled on one track rail. or an interchangeable slide unit only, C shall be indicated. Indicate the length of track rail in. or standard and maximum lengths, see Track rail length in Table. to. on page to. or available model and size, see Table. to.. Table. Types and sizes of C-Lube Linear ay M Table. Types and sizes of C-Lube Linear ay M Material Shape of the slide unit Length of the slide unit code ote :, 0 and can be mounted also from bottom. ote : This can be mounted also from bottom. Remark : marks indicates that interchangeable products are available. Table. Type and sizes of C-Lube Linear ay MUL Material Shape of the slide unit Length of the slide unit code Stainless steel Miniature type MUL Remark: model is not available in MUL series. Material Carbon steel Stainless steel Stainless steel Shape of the slide unit lange type, mounting from bottom lange type, Block type, lange type, mounting from bottom lange type, Block type, igh rigidity long MSG Remark : marks indicates that interchangeable products are available. Carbon steel lange type, mounting from bottom lange type, Blocke type, Compact block type, lange type, mounting from bottom Blocke type, Compact block type, Length of the slide unit Short igh rigidity long Short igh rigidity long Short igh rigidity long Short igh rigidity long Short igh rigidity long Short igh rigidity long igh rigidity long xtra higt rigidity long igh rigidity long xtra higt rigidity long igh rigidity long Short igh rigidity long code MC M MG MTC MT MTG MSC MS MSG MC M MG MTC MT MTG MSC MS M MG MT MTG MT MD MDG MDL MS MSG MT MDC MD MDG MS 0 Table Material codes of C-Lube Linear ays Preload C-Lube Linear ay C-Lube Linear ay M C-Lube Linear ay M C-Lube Linear ay MUL Accuracy class Carbon steel (o symbol (o symbol Clearance for M Clearance for Light preload Medium preload eavy preload Ordinary class igh class Precision class Super precision class Stainless steel (o symbol SL SL (o symbol : TC : T0 : o symbol : T : T : T : o symbol : : P : SP Table Preload of C-Lube Linear ay Preload class and symbol Clearance for M Clearance for Light preload Medium preload TC T0 o symbol T T C-Lube Linear ay C-Lube Linear ay M C-Lube Linear ay M C-Lube Linear ay MUL Remark : marks are also applicable for interchangeable series. Table Accuracy of C-Lube Linear ay Accuracy class and symbol Ordinary class igh class Precision class Super precision class o symbol P SP C-Lube Linear ay C-Lube Linear ay M C-Lube Linear ay M C-Lube Linear ay MUL ote : In M series, applicable combination of the preload and accuracy is limited and shown in Table. : ot applicable to size, 0 and. Remark : marks are also applicable for interchangeable series. Specify this items for an assembled set or an interchangeable single slide unit. Applicable preload and size are shown in Table. or details of preload amount, see Table on page. or applicable accuracy, see Table. In the interchangeable specification, please combine same accuracy codes on both slide unit and track rail. or details of accuracy, see Table. to. on page to. eavy preload T ote : ot applicable to supplemental code /B (Ceramic ball specification : ot applicable to size and 0. : In M series, applicable combination of the preload and accuracy is limited and shown in Table. : Applicable to size, 0 and. : ot applicable to interchangeable specification of size, 0 and. : ot applicable to size, 0 and. Table C-Lube Linear ay M Combination of accuracy and preload Accuracy class Ordinary class igh class Precision class Preload class and symbol and symbol o symbol P Clearance for M TC o symbol Light preload T Medium preload T Remark : marks are also applicable for interchangeable series. = 0.0kgf = 0.lbs. = 0.0inch Super precision class SP

Identification Interchangeability : S Slide unit and track rail can be supplied separately on-interchangeable : o symbol by indicating interchangeable code S. 0 Optional specification Table. C-Lube Linear ay Applicable optional specifications Specifications Supplemental code Set product Track rail only Slide unit only Butt jointing track rail /A Opposite reference surfaces arrangement /D Specified rail mounting hole positions / Ceramic balls /B Appending inspection sheet / Black chrome surface treatment /LR ithout track rail mounting bolts /M o rubber end seals / Track rail with stopper pins /S Under seals /U Matched sets to be used as an assembled group / Table. C-Lube Linear ay M Applicable optional specifications Specifications Supplemental code Set product Track rail only Slide unit only Butt jointing track rail Opposite reference surfaces arrangement Specified rail mounting hole positions Caps for rail mounting holes Append an inspection sheet emale threads for bellows Black chrome surface treatment luoric black chrome surface treatment ith track rail mounting bolts Change of mounting hole size o rubber end seals Butt jointing interchangeable track rail Under seals Double end seals Matched sets to be used as an assembled group Scrapers Applicable special specifications are shown in Table. to.. hen a combination of several special specifications (Table. to. is required, arrange their supplemental codes in alphabetical order. or detail of special specifications, see page to. Table.. C-Lube Linear ay M Applicable optional specifications (or size, 0 and Specifications Supplemental code Set product Track rail only Slide unit only Butt jointing track rail Opposite reference surfaces arrangement Specified rail mounting hole positions Caps for rail mounting holes Append an inspection sheet Black chrome surface treatment ith track rail mounting bolts (Applicable to set order ithout track rail mounting bolts (Applicable to track rail order o rubber end seals Under seals Matched sets to be used as an assembled group /A /D / / / /J /L /L /MA /M / /T /U /V / /Z /A /D / / / /L /MA /M / /U / ote : Applicable to size,, and. : ot applicable to size and 0. : ot applicable to size,, 0 and. Remark : marks indicates that interchangeable products are available. ote : ot applicable to interchangeable specification of stainless steel model. : Applicable to size. : ot applicable to on interchangeable specification. Remark : marks indicates that interchangeable products are available. ote : Applicable to size of carbon steel product. : Applicable to size. : Applicable to only track rail. (Supplemental code LR Remark : marks indicate that interchangeable products are available. Table.. C-Lube Linear ay M Applicable optional specifications (or size and bigger Specifications Supplemental code Set product Track rail only Slide unit only Butt jointing track rail Opposite reference surfaces arrangement Specified rail mounting hole positions Caps for rail mounting holes Append an inspection sheet emale threads for bellows Black chrome surface treatment luoric black chrome surface treatment ith track rail mounting bolts (Applicable to set order ithout track rail mounting bolts (Applicable to track rail order o rubber end seals Rail cover plate Butt jointing interchangeable track rail Double end seals Matched sets to be used as an assembled group Scrapers Specified rail mounting hole positions Black chrome surface treatment ith track rail mounting bolts Upper seals Matched sets to be used as an assembled group Table. Table. Specifications /A /D / / / /J /L /L /MA /M / /PS /T /V / /Z Supplemental code / /LR C-Lube Linear ay Combination of optional specifications C-Lube Linear ay M Combination of optional specifications Remark : marks indicates that this combination can be made. : marks indicates that the combination is available for also interchangeable specification. Remark : marks indicates that this combination can be made. : marks indicates that the combination is available for also interchangeable specification. : Please consult when marks required. Table. C-Lube Linear ay MUL Applicable optional specifications D B LR M S U D J L L MA M PS T U V Z A A D D B LR J M L L S MA U M PS T U on-interchangeable specification V Table. D J L L MA M T U V Z A ote : ot applicable to stainless steel interchangeable specification. : Applicable to carbon steel size and bigger. : ot applicable to non interchangeable specification. Remark : marks indicate that interchangeable products are available. C-Lube Linear ay M Combination of optional specifications ote : hen a combination of /MA and /M is necessary, indicate /MA. Remark : marks indicates that this combination can be made. : marks indicates that the combination is available for also interchangeable specification. : Please consult when marks required. Table. D J L L MA M C-Lube Linear ay MUL Combination of optional specifications LR MA U LR MA U Remark : marks indicates that this combination can be made. T = 0.0kgf = 0.lbs. = 0.0inch U V

Load Ratings and Life Basic dynamic load rating C Conforming to ISO/DIS - The basic dynamic load rating is defined as a constant load both in direction and magnitude under which a group of identical C-Lube Linear ays are individually operated and 0% of those in the group can travel 00 m free from material damage due to rolling contact fatigue. Basic static load rating C 0 Conforming to ISO/DIS - The basic static load rating is defined as a static load that gives a prescribed constant contact stress at the center of the contact area between rolling elements and raceways receiving the maximum load. Life The rating life of C-Lube Linear ay series is obtained from the following calculation formula. L C = 0( P where, L : Rating life, 0 m C : Basic dynamic load rating, P : quivalent load, If the stroke length and the or strokes per minute are known, the life in hours must be corrected by the following formula. L 0 L h = Sn where, L h : Rating life in hours, hours S : Stroke length, : umber of strokes per minute, cpm n ig. Static moment rating direction Static moment rating,, Static safety factor The static safety factor f S of C-Lube Linear ay series is given in the following formula, and general values of this factor are shown in Table. f C 0 S = P 0 where, f S : Static safety factor C 0 : Basic static load rating, : Static load, P 0 Table Static safety factor Operating conditions C, C 0 ig. Load direction The static moment rating is defined as a static moment load (See ig. that gives a prescribed constant contact stress at the center of the contact area between rolling elements and raceways receiving the maximum load. The static moment rating is used in combination with the static safety factor to give the limiting load for normal rolling motion. Operation with vibration and/or shocks igh operating performance ormal operation Load factor f S Actual loads applied to the linear motion rolling guide sometimes exceed the theoretically calculated load due to vibration and shocks caused by machine operation. The actual life is calculated from the following formula while considering the load factor. Table 0 Load factor Condition Smooth operation free from vibration and/or shocks ormal operation Operation with shock loads f.... Dynamic equivalent load hen there is any load in the direction other than basic dynamic load rating or combined load, dynamic equivalent load is obtained for life calculation. rom each directional load, converted load equal to downward or lateral is given by following formulae. where, re : Converted downward load, ae : Converted lateral load, r : Downward load, a : Lateral load, M 0 : moment, m M X : moment, m M Y : moment, m k r,k a : Conversion factor by load direction (See Table C 0 : Basic static load rating, : static moment, m : static moment, m : static moment, m C 0 re = k r r + M 0 + M X C 0 C 0 ae = k a a + T M Y Y Table Conversion factor by load direction C-Lube Linear ay C-Lube Linear ay M C-Lube Linear ay M C-Lube Linear ay MUL r a Conversion factor k r r 0 r 0.. k a..... rom the converted downward and lateral load, mean equivalent dynamic load must be corrected by the following formula. P= X re +Y ae where, P : Mean equivalent dynamic load, X,Y : Mean equivalent dynamic load factor (See Table re : Converted downward load, : Converted lateral load, ae Table Mean equivalent dynamic load factor Condition X re ae re ae 0. Static equivalent load hen there is any load in the direction other than basic dynamic load rating or combined load, mean equivalent static load is obtained for static safety factor calculation. rom each directional load, converted load equal to downward or lateral is given by following formula. where, P 0 : Static equivalent load, r : Downward load, a : Lateral load, M 0 : moment, M X : moment, M Y : moment, k 0r,k 0a : Conversion factor by load direction (See Table C 0 : Basic static load rating, : static moment, : static moment, : static moment, C 0 P 0 = k 0r r + k 0a a + M 0 + M X + M Y Table Conversion factor by load direction C-Lube Linear ay C-Lube Linear ay M C-Lube Linear ay M C-Lube Linear ay MUL C 0 C 0 r Conversion factor k 0r r 0 r 0 a.. = 0.0kgf = 0.lbs. = 0.0inch Y 0. k 0a.....

Accuracy Preload Accuracy of the assembled set of C-Lube Linear ay are shown in Table. to.. Table. Accuracy of C-Lube Linear ay Item Dim. Tolerance Dim. Tolerance Dim. variation of Dim. variation of Dim. variation of for multiple sets Parallelism in operation of Parallelism in operation of ote : : Remark : Parallelism m 0 C A D Classification (Symbol C to A D to B B igh 0.0 0.0 0.0 0.0 0.0 Refer to ig.. Refer to ig.. igh ( Precision (P Precision P 0.00 0.0 0.00 0.00 unit : 0.0 Dimensional variation of dimension means the size variation between the slide units mounted on the same track rail when the dimension is measured at the same measuring position of track rail. Applicable for series. Aiso applicable to size to of C-Lube Linear ay M. Table. Accuracy of C-Lube Linear ay M and M Classification (Symbol Ordinary igh Item o symbol Dim. Tolerance Dim. Tolerance Dim. variation of Dim. variation of 0.00 0.00 0.0 0.0 0.0 0.00 0.0 0.0 Dim. variation of for multiple sets Parallelism in operation of Parallelism in operation of ote : : Remark : Parallelism m 0 C A D C to A D to B B 0.0 Ordinary (no symbol 0.0 and igh Precision P 0.0 0.0 0.00 0.00 0.0 Refer to ig.. Refer to ig.. ( Precision (P Super precision (SP unit : Super precision SP 0.00 0.0 0.00 0.00 Dimensional variation of dimension means the size variation between the slide units mounted on the same track rail when the dimension is measured at the same measuring position of track rail. Applicable for series. or size to of C-Lube Linear ay M, see Table.. Table. Accuracy of C-Lube Linear ay MUL Item Dim. Tolerance Dim. Tolerance Dim. variation of Dim. variation of Parallelism in operation of C to A Parallelism in operation of Parallelism m Classification (Symbol 0 C A D D to B Ordinary Refer to ig.. igh Average amount of preload for C-Lube Linear ay series is shown in Table. In case, high rigidity and/or damping are needed, the preload amount is recoended to be / of the external force. owever, excessive preload will cause short life. Table Preload amount Item Symbol Preload class Clearance preloado symbol Light preload TC T0 T Preload amount 0 0 0 0.0 C 0 o symbol 0.00 0.00 Medium preload.0 C 0 0.00 0.00 eavy preload.0 C 0 0.00 0.0 0.00 0.0 ote : Approx. 0m clearance : Zero or minimal amount of clearance Zero or minimal amount of preload Refer to ig.. : Remark : C 0 means basic static load rating. Ordinary (no symbol and igh ( unit : ote : Dimensional variation of dimension means the size variation between the slide units mounted on the same track rail when the dimension is measured at the same measuring position of track rail. B e Y axis Typical application Smooth motion To absorb slight misalignment Smooth motion Smooth and precise motion Minimum vibration Load is equally balanced. Smooth and precise motion Medium vibration Medium overhung load Vibration and/or shocks Large overhung load eavy cutting Geometrical moment of inertia igh rigidity design of C-Lube Linear ay MUL is achieved by adopting a U-shaped track rail. Table shows the moment of inertia of sectional area of track rails. Table C-Lube Linear ay MUL Moment of inertia of sectional area of track rails X axis 0 0 0 00 0 ig.. Length of track rail L C-Lube Linear ay Parallelism in operation 0 0 000 000 000 ig.. Length of track rail L C-Lube Linear ay M and M Parallelism in operation 0 0 ig.. 0 0 0 00 000 Length of track rail L C-Lube Linear ay MUL Parallelism in operation MU MUL Moment of inertia of sectional area I X.0.0 I Y Center of gravity e.0..0. = 0.0kgf = 0.lbs. = 0.0inch

Optional special specifications for use under special environment C-Lube Linear ay series with the special specifications shown in Table. to. are optionally available for various applications. hen ordering, add any supplemental codes onto the identification. If a combination of special specifications is required, indicate the supplemental codes in alphabetical order. These optional items can be combined to achieve further improvements in performance. Butt jointing track rails -A -B -A -B -A -B -A -B Opposite reference surfaces arrangement Reference mounting surface of track rail Reference mounting surface of track rail /A /D The reference mounting surface of track rail is made opposite to the standard side. The accuracy of dimension including parallelism in operation is the same with that of standard specification. Specified track rail mounting hole positions mark / The mounting hole positions of track rail can be specified by specifying dimension at the left end, which is the distance from the mounting hole nearest to the left end of the track rail to the left end face of the track rail in sight of mark on the slide unit. hen ordering, add the dimension (in after /. Dimension can be specified in a limited range. Consult for further information. If long dimension is required, imperfect mounting hole may remain. ith caps for rail mounting holes (for M and M series / Specify prepared caps for track rail mounting holes are appended. These caps cover the track rail mounting holes to improve the sealing performance in the linear motion direction. Aluminum caps are also available. Consult for further information. Ceramic ball specification Table C /B G C G /B /B /B /B /B C /B /B G /B C /B /B G /B C 0 0 0 0 0 0 C 0 0 0 0 0 0 0 Caps (Made of synthetic resin hen the required length of non-interchangeable track rail exceeds the maximum length shown in page to, two or (for series /B more track rails can be used by butt jointing them in the direction of linear motion. or the length and the of butt jointing track rails, please consult. Steel balls in the slide unit are changed to ceramic (silicon nitride material. Load ratings and static moment ratings are shown in Table. Load ratings and static moment ratings of ceramic ball specification C-Lube Linear ay m.... 0........ m...0..............0.... m. 0.......... 0....0...... ote : The upper values in the and column apply to one slide unit, and the lower values apply to two slide units in close contact. ith inspection sheet The inspection sheet recording dimensions and (See Accuracy, dimensional variations of and, and parallelism in operation of the slide unit is attached to each set. ith female threads for bellows (for M and M series /J /JR /JL emale threads for bellows ith female threads for bellows emale threads for bellows emale threads for mounting bellows are provided on the interchangeable slide unit or the interchangeable track rail of C-Lube Linear ay M and M series. or details of related dimensions, see Table. and.. q /J emale threads are provided at both ends of the slide unit or the track rail. w /JR emale threads are provided at the right end of the slide unit in sight of mark. e /JL emale threads are provided at the left end of the slide unit in sight of mark. (for assembled set of M and M series /J /JJ /JR /JS /JJS emale threads for bellows emale threads for bellows or an assembled set of interchangeable or non-interchangeable specification, female threads for mounting bellows are provided on the slide unit and the track rail. or the details of related dimensions, see Table. and.. q /J emale threads are provided at both ends of the track rail, and at the slide unit ends which are the closest to the track rail ends. (In case only one slide unit is assembled, female threads are provided at both ends. w /JJ emale threads are provided at both ends of the track rail, and at all ends of all slide units. (Applicable, when the of slide units is two or more. In case only one slide unit is assembled, indicate /J. e /JR emale threads are provided at both ends of the track rail. r /JS emale threads are provided at the slide unit ends which are the closest to the track rail ends. (In case only one slide unit is assembled, female threads are provided at both ends. t /JJS emale threads are provided at all ends of all slide units. (Applicable, when the of slide units is two or more. In case only one slide unit is assembled, indicate /JS. = 0.0kgf = 0.lbs. = 0.0inch Slide unit Track rail Table. C-Lube Linear ay M Dimension of female threads for bellows a a a a D D b b B b b Block Type unit : Slide unit Track rail M a a b b b b M L a a depth depth MTC MT MTG MSC M. M MS MSG MTC MT.. MTG MSC MS MSG MTC MT MTG MSC MS MSG MTC MT MTG MSC MS MSG MTC MT MSC MS MT MS b b.. a a M B depth lange Type b b M depth M depth M depth Grease nipple AM. 0 a a M M 0 M M 00 00 M ote : The specification and mounting position of grease nipple are different from those of the standard specification product. models are provided with a special specification grease nipple (PB type. or details of dimension, consult for further information. : The values are for the slide unit with female threads for bellows at both ends. Remark : The table shows representative model s but is also applicable to stainless steel models. L M M M M M0

Optional special specifications for use under special environment Table. C-Lube Linear ay M Dimension of female threads for bellows a a D b b b b b a a M B depth lange Type b M depth M depth Grease nipple AM b b L M depth Black chrome surface treatment /LC /LR /LCR A black permeable chrome film is formed to improve corrosion resistance. q /LC Treatment is applied to the casing. w /LR Treatment is applied to the track rail. e /LCR Treatment is applied to the casing and the track rail. or detail of applicability, see Table. to. on page to. o end seal (for, M and M series / nd pressure plate nd pressure plate Track rail with stopper pins (for non-interchangeable series /S Stopper pin Stopper pin b b b b a a D MT MD MS MT MTG MS MSG MT MTG MD MDG MS MSG MT MTG MTL MD MDG MDL MS MSG MT MTG MT MD MDG MD MT MTG MTL MD MDG MDL ote : The specification and the mounting position of grease nipple are different from those of the standard specification product. models are provided with a special specification grease nipple (PB type. or details of dimension, consult for further information. : The values are for the slide unit with female threads for bellows at both ends. Remark : The table shows representative model s but is also applicable to stainless steel models. B M depth a a a a Block Type Compact Block Type unit : Slide unit Track rail a a b b b b M M L a a depth depth... M 0. M... 0 M. M 0. 0 M. M 0. 0 0 M M 0 M M 0 M M0 D B a a M depth luorine black chrome surface treatment (for M and M series ith track rail mounting bolts (for M, MUL and set order of M /LC /LR /LCR After forming a black permeable chrome film, the surface is coated with fluorine resin for further improvement in corrosion resistance. This treatment is also effective in preventing the adhesion of foreign substances on the surface. q /LC Treatment is applied to the body of slide unit. w /LR Treatment is applied to the track rail. e /LCR Treatment is applied to the body of slide unit and the track rail. or detail of applicability, see Table. to. on page to. Change of mounting hole size and female threads size (for M and MSL /MA Track rail mounting bolts are appended according to the of mounting holes. ithout track rail mounting bolts (for and interchangeable track rail order of M Track rail mounting bolts are not appended. /M /M The track rail mounting holes for M of M is changed to M. If with track rail mounting bolts is also required, specify /MA. nd rubber seals at both ends of slide unit are replaced by steel end pressure plates (not in contact with the track rail to reduce frictional resistance. The under seals are not assembled. This specification is not effective for dust protection. Rail cover plate for track rail (for non-interchangeable M series Rail cover plate /PS After mounting the track rail, the top surface of track rail is covered with a U-shaped thin stainless steel plate for further improvement in sealing performance. The rail cover plate is delivered as assembled on the track rail. end seals must be replaced with the special end seals. hen mounting the cover plate, refer to the attached instruction manual for rail cover plate. To prevent the slide unit of C-Lube Linear ay from slipping off of the track rail, a stopper pins are provided at both ends of the track rail. or related dimensions, see Table below. Table C-Lube Linear ay Track rail with stopper pins (Supplemental code /S b a M M c a b c.... 0 Butt-jointing interchangeable track rail (for interchangeable specification of M and M series = 0.0kgf = 0.lbs. = 0.0inch unit : a b c Remark : The table shows representative model s but is also applicable to all the models in the same size of and series... /T A special interchangeable track rail of which both ends are finished for butt jointing in the direction of linear motion is provided. Use the track rails having the same interchangeable code for butt jointing. or the butt jointing for non-interchangeable specification, indicate butt-jointing track rail /A.

Optional special specifications for use under special environment ith under seals (for and M series Under seals are attached to M series as standard specification. /U ith upper seals (for MUL series /U D C ith double end seals (for assembled set of M and M series /V /VV Matched sets to be used as an assembled group (Applicable to non-interchangeable spec. / Set A Set B Under seal To prevent foreign substances intruding from the lower side of Linear ay, rubber seals are provided on the bottom faces of slide unit. or size, see Table. Table dimension of slide unit with under seals (Supplemental code /U M M unit : A Rubber seals are attached to the upper side face of the slide unit to prevent foreign materials from entering from the upper side, so that the mounting reference surface D cannot be used. Table shows sizes of the slide unit when upper seals are attached. Table Dimension of the slide unit with upper seals (Supplemental code /U MU MUL A.. B B unit : Remark : In case upper seals specification, the reference surface of slide unit can not be used. nd seal nd seal Spacer Double end seals are provided on the slide unit of assembled set of interchangeable specification or noninterchangeable specification for more effective dust protection. or the total length of the slide unit with double end seals, see the Table. q/v Double end seals are provided at the ends of slide units which are the closest to the ends of the track rail. (In case only one slide unit is assembled, double end seals are provided at both ends. w/vv Double end seals are provided at all ends of all slide units. (Applicable when the of slide units is two or more. In case only one slide unit is assembled, indicate /V. Table Dimension of the slide unit with double end seals (Supplemental code /VV (L (L or two or more sets of C-Lube Linear ay used on the same plane, the dimensional variation of of C-Lube Linear ay is kept within the specified range. The dimensional variation of dimension in matched sets is the same as that of a single set. Indicate the of sets after /. (x: CR/ ith scrapers (for interchangeable single slide unit of M and M series /Z /ZR /ZL Metal scrapers are provided on the slide unit of interchangeable specification. The scraper (non-contact type is used to effectively remove large particles of dust or foreign matter adhering to the track rail. or the total length of the slide unit with scrapers, see Table. q /Z Scrapers are provided at both ends of the slide unit. w /ZR A scraper is provided at the right end of the slide unit in sight of mark. e /ZL A scraper is provided at the left end of the slide unit in sight of mark. M M M M M M MT SL M SL MT ote : dimension of and MT models is the same as the dimension without under seals. Remark : The table shows representative model s but is also applicable to all the models in the same size of,, M and MT series. 0... ith double end seals (for interchangeable single slide unit of M and M series /V /VR /VL Double rubber end seals are provided on the interchangeable slide unit for more effective dust protection. or the total length of the slide unit with double end seals, see the Table. q /V Double end seals are provided at both ends of the slide unit. w /VR Double end seals are provided at the right end of the slide unit in sight of mark. e /VL Double end seals are provided at the left end of the slide unit in sight of mark. MC M MG MC M MG MC M MG MC M MG MC M M Remark : L L 0 0 0 0 0 0 0 0 M M MG M MG M MG MTL M MG MT M MG MTL unit : L L 0 0 0 The above table shows representative model s but is applicable to all models of the same size. : The values are for the slide unit with double end seals at both ends. = 0.0kgf = 0.lbs. = 0.0inch

Optional special specifications for use under special environment Lubrication and Dust protection ith scrapers (for assembled set of M and M series Scraper Spacer nd seal /Z /ZZ Metal scrapers are provided on the slide units of assembled set of interchangeable specification or non-interchangeable specification. Scrapers (non-contact type are used to effectively remove large particles of dust or foreign matter adhering to the track rail. or the total length of the slide unit with scrapers, see Table. q /Z Scrapers are provided at the ends of slide units which are the closest to the ends of the track rail. (In case only one slide unit is assembled, scrapers are provided at both ends. w /ZZ Scrapers are provided at all ends of all slide units. (Applicable when the of slide units is two or more. In case only one slide unit is assembled, indicate /Z. Table Dimension of the slide unit with scrapers (Supplemental code /Z /ZZ Scraper (L (L Scraper unit : L L L L MC 0 M M M 0 MG MG MC M 0 M MG MG 0 0 M MC MG 0 M 0 MTL MG M MC 0 MG M 0 MT MG M 0 MC 0 MG M MTL M Remark : The above table shows representative model s but is applicable to all models of the same size. : The values are for the slide unit with scrapers at both ends. Lithium-soap base grease (MULTMP PS o. : KYODO YUSI is pre-packed in C-Lube Linear ay and lithium-soap base grease containing extreme pressure additive (ALVAIA grease P : SLL is pre-packed C-Lube Linear ay M, M and MUL. Additionally, C-Lube (Capillary sleeve a component part is placed in the ball recirculation path, thereby extending the re-lubrication (greasing interval time and maintenance work for a long period. C-Lube Linear ay is provided with an oil hole and with grease nipple shown in Table and. Supply nozzles matching the size of grease nipple are available. or these parts for lubrication, consult for further information. C-Lube Linear ay is dust protected with special rubber seals. But, if large amount of fine contaminants may present, or if large particles of foreign matter such as dust or chips may fall on the track rail, it is recoended to provide protective covers such as bellows for the entire linear motion mechanism. Bellows to match the dimensions of C-Lube Linear ay are optionally available. They are easy to mount and highly effective for dust protection. If required, consult. Table Oil hole M 0 d d Rubber part of end seal nd seal d 0. Casing nd plate Dimension of oil hole d...... unit : Table Grease nipple unit : Grease nipple Type Shape and dimension MT M M M M M M M M M A-M B-M A-M B-M idth across flats. M M Approx... idth across flats. R Approx.. quivalent to JIS type R idth across flats M.. idth across flats M... 0. MT SL M SL MU... MUL. Remark : The table shows representative model s but is also applicable to all the models in the same size. M M M M JIS type Approx.. quivalent to JIS type idth across flats 0 PT/.. Remark : The table shows representative model s but is also applicable to all the models in the same size. = 0.0kgf = 0.lbs. = 0.0inch

Precautions for use q Mounting surface, reference mounting surface, and general mounting structure To mount C-Lube linear way, correctly fit the reference mounting surfaces B and D of the slide unit and track rail to the reference mounting surfaces of the table and the bed, and then fix them tightly. (See ig.. and. The reference mounting surfaces B and D and the mounting surfaces A and C of C-Lube Linear ay are accurately finished by grinding. Stable and high accuracy liner motion can be obtained by finishing the mating mounting surfaces of machines or equipment with high accuracy and correctly mounting the guide on these surfaces. The slide unit reference mounting surface is always the side surface opposite to the mark. The track rail reference mounting surface is identified by locating the mark on the top surface of the track rail. The track rail reference mounting surface is the side surface above the mark (in the direction of the arrow. (See ig.. and. C C A D D B ig.. C-Lube Linear ay, M and M Reference mounting surfaces and general mounting structure Reference mounting surfaces D B Track rail Reference mounting surfaces mark Slide unit mark Slide unit ig.. C-Lube Linear ay, M and M Reference mounting surfaces mark Track rail ig.. C-Lube Linear ay MUL Reference mounting surfaces Reference mounting surfaces D mark w Corner radius and shoulder height of reference mounting surfaces It is recoended to make a relieved fillet at the corner of the mating reference mounting surfaces as shown in ig.. Otherwise, corner radius R and R are recoended shown in Table. and.. Table. and. shows recoended shoulder heights and radius of the reference mounting surfaces. B Table. h R M M 0 MT MS MT MS MT MS MT MS MT MS MT MS C-Lube Linear ay and M Shoulder height and radius of the reference mounting surfaces R Slide unit Shoulder height h..... Slide unit Relieved radius R max. 0. 0. 0. 0. 0. 0. 0.. Track rail Shoulder height h unit : Track rail 0.... Relieved radius R max. ote : or with under seals of the size models, 0. is recoended. : or with under seals (supplemental code /U, it is recoended to use a value obtained by subtracting from the value h shown in the table. Remark : The table shows representative model s but is also applicable to all the models in the same size. h R.. R 0. 0. 0. 0. 0.. Table. h R C-Lube Linear ay M and MUL Shoulder height and radius of the reference mounting surfaces R Slide unit Slide unit Shoulder height h.. Relieved radius R max. Track rail Shoulder height h unit : Track rail Relieved radius R max. MT SL. MD SL 0. M SL. MD 0 SL 0. MT. MD 0. M 0. M M M M M.. MU.. 0. MUL. ote : or with under seals (supplemental code /U, it is recoended to use a value obtained by subtracting 0. from the value h shown in the table. : Provide a relieved fillet as shown ig.. Remark : The table shows representative model s but is also applicable to all the models in the same size. e Multiple slide units mounted in close distance hen using multiple slide units in close distance to each other, actual load may be greater than the calculated load depending on the mounting accuracy of the slide units on the mounting surfaces and the reference mounting surfaces of the machine. It is suggested in such cases to assume a greater load than the calculated load. r Operating temperature The C-Lube Linear ay must be used under 0 C (maximum. h R R A B ig. Relieved radius shape of reference mounting surface t Cleaning Do not wash C-Lube Linear ay with organic solvent and/or white kerosene, which have the ability of removing fat nor leave them in contact with the above agents. ig.. C-Lube Linear ay MUL Reference mounting surfaces and general mounting structure = 0.0kgf = 0.lbs. = 0.0inch

Mounting q Assembling two or more sets of C-Lube Linear ay specification In the case of an interchangeable specification product, assemble a slide unit and a track rail with the same interchangeable code. ( S slide unit + S track rail on-interchangeable specification Use an assembly of slide unit and track rail as delivered without changing the combination. Matched sets to be used as an assembled group Special specification products of matched sets (by supplemental code / are delivered as a group in which dimensional variations are specially controlled. Mount them without mixing with the sets of another group. w Assembling a slide unit and a track rail hen assembling C-Lube Linear ay, correctly fit the slide unit mounted on a steel ball holder to the groove of the track rail, and then move the slide unit gently from the steel ball holder to the track rail in parallel direction. Steel balls are retained in C-Lube Linear ay, so the slide unit can be separated freely from the track rail. owever, the slide unit can be assembled on the track rail much easier by using the steel ball holder. Steel ball holder is appended as an accessory to the interchangeable slide unit of C-Lube Linear ay as shown in Table. The steel ball holder for another models is also available. If required, consult for further information. Table C-Lube Linear ay and M s to which a steel ball holder is appended C-Lube Linear ay C-Lube Linear ay M C C 0 MT SL C, G C, G M SL C, G C, G MT SL G G MDC, G SL G G MDC, G0SL G G MDC, GSL G MT MD e Machining accuracy of mounting surfaces Inadequate mounting accuracy of C-Lube Linear ay will affect the operating accuracy and life adversely, so mounting must be carried out with care. hen multiple sets are mounted, the parallelism between the two mounting surfaces of machines must be prepared, in general, as shown in Table. If mounting parallelism is poor, frictional resistance will steeply increase giving a warning signal, which can be used to perform high accuracy mounting. Table Parallelism between two mounting surfaces unit : m Class Parallelism Ordinary o symbol igh Precision P Super precision SP 0 r Cleaning the mounting surfaces hen mounting C-Lube Linear ay, first clean all mounting and reference mounting surfaces. (See ig. Remove burrs and blemishes from the reference mounting surfaces and mounting surfaces of the machine using an oil-stone, etc., and then wipe the surfaces with clean cloth. Remove rust preventive oil and dirt from the reference mounting surfaces and mounting surfaces with clean cloth. ig. Cleaning the mounting surfaces t Plugging-in of caps for rail mounting holes hen plugging the caps for rail mounting holes (supplemental code / into the mounting holes of track rail, tap in the cap gently by applying a flat plate on the top face of the cap until the top face of the cap becomes level with the top face of the track rail. Table. C-Lube Linear ay (standard type and maximum lengths of track rails lat plate ig. Plugging-in of caps for rail mounting holes y Tightening torque of mounting bolts The standard torque values for C-Lube Linear ay mounting bolts are shown in Table. and.. hen machines or equipment are subjected to serve vibration, shock, large fluctuating load, or moment load, the bolts should be tightened with a torque. to. times higher than the standard torque values shown. hen the mating member material is cast iron or aluminum, tightening torque should be lowered in accordance with the strength characteristics of the material. Table. Tightening torque m Bolt size Carbon steel bolt Stainless steel bolt Strength division. Property division A-0 M 0... M 0..0. M 0...0 M.. M..0. M0.. M. 0 Remark : or C-Lube Linear ay, M (size, 0 and and MUL, see Table.. Track rail lengths Item C-Lube Linear ay M and M Tightening torque of mounting bolts and maximum lengths of track rails are shown in Table. to.. Track rail in any length are also available. Simply indicate the necessary length of track rail in millimeter ( in the identification. or the tolerance of dimention and Track rail length, consult for further information. length Ln Mounting hole pitch Reference Over (Incl. dimension Under L n (umber of mounting holes M M 0 0 00.. 0 0 0 00 0.. 0 0 0 0 0.. 0 Table. C-Lube Linear ay, M (size, 0 and and MUL Tightening torque of mounting bolts Bolt size M 0. M.. M.0. M.. M 0. M 0. M 0. M.0 00 0 0 0.. 000 0.. 000 Tightening torque m Carbon steel bolt Stainless steel bolt Strength division. Property division A-0-0. - 0. - 0. - 0.0.... -.0 -. In non-interchangeable specification, for track rail longer than the maximum length shown in Table. to., butt-jointing track rails are available upon request. In this case, indicate supplemental code /A in the identification. dimensions at both ends are the same unless otherwise specified. To change these dimensions, specify the specified rail mounting hole positions (supplemental code / of special specification. 0 00 unit : 0 00 00 Maximum length Maximum of track rails for butt jointing Maximum length of butt jointing track rails 0 0 ote : ot applied to optional specification track rail stopper pins (supplemental code /S. : The track rails can be manufactured up to the maximum length shown in parentheses. If required, please consult for further information. : ot applicable to interchangeable specification. Remark : The table shows representative model s but is also applicable to all the models in the same size. = 0.0kgf = 0.lbs. = 0.0inch

Track rail lengths Table. C-Lube Linear ay (wide type and maximum lengths of track rails Table. C-Lube Linear ay M and maximum lengths of track rails n (umber of mounting holes n (umber of mounting holes n (umber of mounting holes Item Table. length Ln Mounting hole pitch Reference Over (Incl. dimension Under Maximum length Maximum of track rails for butt jointing Maximum length of butt jointing track rails L ote : ot applied to optional specification track rail stopper pins (supplemental code /S. : The track rails can be manufactured up to the maximum length shown in parentheses. If required, please consult : ot applicable to interchangeable specification. Remark : The table shows representative model s but is also applicable to all the models in the same size. Item C-Lube Linear ay M and maximum lengths of track rails length Ln Mounting hole pitch Reference Over (Incl. dimension Under Maximum length n (umber of mounting holes L 0 0 0 0.. 0 00 0 0 0 00.. 0 0 0 M M M 0 000 M 0 0 0 00.. 00.. 0 0.. 0 000 ote : hen specifying a butt-jointing interchangeable track rail (supplimental code /T, pay attention to the dimension at the butt-jointing part. : ot applicable to the track rail with female threads for bellows (Supplemental code /J. : The dimension of stainless steel product is the half value of dimension. : The track rails can be manufactured up to the maximum length shown in parentheses. If required, please consult for further information. Remark : The table shows representative model s but is also applicable to all the models in the same size. unit : 0.. 0 000 unit : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000 000 0 000 000 000 000 000 0 0 0 000 000 0 0 0 0 0 0 0 0 000 M 000 M MSL MSL MSL MSL 0.. 0 0 for further information. 0 0 0 0 Item ote : ot applicable to the track rail with female threads for bellows (Supplemental code /J : The track rails can be manufactured up to the maximum length shown in parentheses. If required, please consult Remark : The table shows representative model s but is also applicable to all the models in the same size. Table. length Ln Mounting hole pitch Reference Over (Incl. dimension Under Maximum length Item length Ln Mounting hole pitch Reference Over (Incl. dimension Under Maximum length C-Lube Linear ay MUL and maximum lengths of track rails M M M M M M M 0 00.. L Item length Ln Mounting hole pitch Reference Over (Incl. dimension Under Maximum length for further information. unit : unit : M SL M0SL MSL MSL MSL MSL MSL 0 00 0 0.. 000 n (umber of mounting holes L 0 00 0 00 000 0 00 0 0 00 0 0 0 00.. 0 000 0 0 00 0 000 0 00.. 000 0 0 00 0 000 0 0 00 000 0 0 000 0 0 0 000 0 000 000 0 0 0 0 0 000 0 000 000 0.. 0 000 0 0 0 0 0 unit : MU MUL 0 0 0.. 0 0.. ote : The track rails can be supplied with up to the length shown in parentheses as maximum. If required, please consult for further information. = 0.0kgf = 0.lbs. = 0.0inch

C-Lube Linear ay type CG Oil hole -M depth (L (L (L (L -M depth d C C M G G C C G G h C, L C C G C G C G C G C G C G Mass (Reference g Slide unit Track rail (per 00.... 0 0 Dimension of assembly L L M depth..... 0...... Dimension of slide unit ote : Track rail lengths L are shown in Table.. : The directions of basic dynamic load rating (C, basic static load rating (C 0 and static moment rating (, and are shown in the sketches below. The upper values in the and column apply to one slide unit, and the lower values apply to two units in close contact. Remark : The appended bolts for mounting track rails are hexagon socket head bolts of JIS B or equivalent, or cross-recessed head cap screws for precision equipment. : Oil hole is provided for (C to (C, G models.... 0 C, C 0 T0 0.................. 0 M. M. M M. M M M...... d h. 0 Dimension of track rail...........0 type 0.......0 Length of slide unit C Short o symbol G igh rigidity long.. 0. code G,,,,,, umber of slide unit (two slide units Length of track rail ( Appended mounting bolt for track rail Bolt size length Cross-recessed head screw for precision equipment M exagon socket head bolt M exagon socket head bolt M exagon socket head bolt M exagon socket head bolt M0 exagon socket head bolt M exagon socket head bolt M xample of identification for assembled set Part code C R Basic Basic dynamic static load rating load rating C 0 0 0 0 0 0 0 0 0 00 00 Preload symbol C 0 00 0 0 0 0 0 0 0 0 00 00 0 0 00 0 Class symbol Static moment rating m............0 0.0.0.0. m......... 0.................. 0 0. 0 code m... 0.........0......0.... 0....... T P S /U code S specification on interchangeable o symbol specification Preload amount T0 Clearance o symbol T Light preload C C G C G C G C G C G C G Supplemental code Special specification A, D,, B,, LR, M,, S, U, P Accuracy class igh Precision In case ordering track rail only, model code is changed as shown below. Track rail of interchangeable code LL-B (x: LLRBPS = 0.0kgf = 0.lbs. = 0.0inch

C-Lube Linear ay ide type CG -M depth (L (L (L (L -M depth Oil hole d C0C 0 GG C G C G h C, 0 L C 0 0 C G C G C G C G C G Mass (Reference g Slide unit Track rail (per 00.. 0 0 0 0. Dimension of assembly... 0 0.... Dimension of slide unit L L M depth d h ote : Track rail lengths L are shown in Table.. : The directions of basic dynamic load rating (C, basic static load rating (C 0 and static moment rating (, and are shown in the sketches below. The upper values in the and column apply to one slide unit, and the lower values apply to two units in close contact. Remark : The appended bolts for mounting track rails are hexagon socket head bolts of JIS B or equivalent, or cross-recessed head cap screws for precision equipment. : Oil hole is provided for (C, G0 to (C, G models...... 0... 0... C, C 0 T0 0.............. M.. M M M M M......... 0. 0 Dimension of track rail............... xample of identification for assembled set 0 code ide type Length of slide unit C Short o symbol G igh rigidity long 0,,,,, umber of slide unit (two slide units Length of track rail ( G Bolt size length Cross-recessed head screw for precision equipment M. Appended mounting bolt for track rail exagon socket head bolt M exagon socket head bolt M exagon socket head bolt M exagon socket head bolt M exagon socket head bolt M Part code C R Basic Basic dynamic static load rating load rating C 0 0 0 0 00 0 0 0 0 00 Preload symbol C 0 0 0 00 0 0 0 0 0 0 00 Class symbol Static moment rating m........... m...... 0...0 0... 0....... 0. 00 0. 0. code S m................... 0.0..... 0 Supplemental code T P /U code S specification on interchangeable o symbol specification Preload amount T0 Clearance o symbol T Light preload C 0 0 C G C G C G C G C G Special specification A, D,,, LR, M,, S, U, P Accuracy class igh Precision In case ordering track rail only, model code is changed as shown below. Track rail of interchangeable code LL-B (x: LLRBPS = 0.0kgf = 0.lbs. = 0.0inch

C-Lube Linear ay M lange type, mounting from bottom Short MC M igh rigidity longmg d (L (L -d (L (L -d h MC(SL L MC MC M M MG MG MC MC M M MG MG MC MC M M MG MG SL SL SL SL SL SL SL SL SL Mass (Reference Slide unit kg 0. 0. 0. 0. 0. 0. 0. 0. 0. Track rail kg/m...0 Dimension of Dimension of slide unit Dimension of track rail Recoended Basic Basic Static moment rating assembly mounting bolt dynamic static for track rail load rating load rating C C 0 L L d d h Bolt size length m m m. ote : Track rail lengths L are shown in Table.. : Track rail mounting bolts are not appended. exagon socket bolts of JIS B strength division. or equivalent are recoended. Values in parentheses are applicable to the track rail of supplemental code /M of special specification. : The directions of basic dynamic load rating (C, basic static load rating (C 0 and static moment rating (, and are shown in the sketches below. The upper values in the and column apply to one slide unit, and the lower values apply to two units in close contact. Remark : Values in parentheses are applicable to the track rail of supplemental code "/M" of special specification..... 0. 0 0........ 0..... (.. (.. (. M (M M M xample of identification for assembled set,, code M G umber of slide unit (two slide units Length of track rail ( Part code C R 0 0 0 0 00 0 0 00 0 0 0 00 0 Material o symbol igh carbon steel SL Stainless steel.. 00....... 00 Preload amount Tc Clearance o symbol T Light preload T Medium preload...... 00 o symbol P SP MC MC M M MG MG MC MC M M MG MG MC MC M M MG MG T P S /U Accuracy class SL SL SL SL SL SL SL SL SL Material code Preload symbol Class symbol code Supplemental code code C, C M lange type, 0 S T0 T mounting from bottom specification X o on interchangeable Length of slide unit symbol specification C Short o symbol G igh rigidity long Special specification A, D,,,, J, L, L, MA, M,, T, U, V,, Z Ordinary igh Precision Super precision In case ordering track rail only, model code is changed as shown below. Track rail of interchangeable M code L (x: LRPS = 0.0kgf = 0.lbs. = 0.0inch

C-Lube Linear ay M lange type, mounting from bottom Short MC M igh rigidity longmg d (L (L -d (L (L -d h MC(SL L MC MC SL Mass (Reference Slide unit kg 0. Track rail kg/m Dimension of Dimension of slide unit Dimension of track rail Recoended Basic Basic Static moment rating assembly mounting bolt dynamic static for track rail load rating load rating C C 0 L L d d h Bolt size length m m m 0 00 MC MC SL M M SL 0..0 0 0. 0 0 0 M 00 0 M M SL MG MG SL.0.. 0 000 0 0 0 0 MG MG SL MC M 0... 00 0.. 0 0 0 M 00 00 00 00 0 00 MC M M... 00 0... 0 M0 00 0 0 00 0 M ote : Track rail lengths L are shown in Table.. : Track rail mounting bolts are not appended. exagon socket bolts of JIS B strength division. or equivalent are recoended. : The directions of basic dynamic load rating (C, basic static load rating (C 0 and static moment rating (, and are shown in the sketches below. The upper values in the and column apply to one slide unit, and the lower values apply to two units in close contact. C, C 0 T0 xample of identification for assembled set code M G Part code C R Material code Preload symbol Class symbol code Supplemental code T P S /U lange type, M mounting from bottom Length of slide unit C Short o symbol G igh rigidity long,, umber of slide unit (two slide units Length of track rail ( Material o symbol igh carbon steel SL Stainless steel code S specification o on interchangeable symbol specification Preload amount Tc Clearance o symbol T Light preload T Medium preload Special specification A, D,,,, J, L, L, MA,, T, U, V,, Z o symbol P SP Accuracy class Ordinary igh Precision Super precision In case ordering track rail only, model code is changed as shown below. Track rail of interchangeable M code L (x: LRPS = 0.0kgf = 0.lbs. = 0.0inch

C-Lube Linear ay M lange type, Short MTC MT igh rigidity longmtg d (L (L -M (L (L -M h MTC(SL L MTC MTC SL MT MT SL MTG MTG SL MTC MTC SL MT MT SL MTG MTG SL MTC MTC SL MT MT SL MTG MTG SL Mass (Reference Slide unit kg 0. 0. 0. 0. 0. 0. 0. 0. 0. Track rail kg/m...0 Dimension of Dimension of slide unit Dimension of track rail Recoended Basic Basic Static moment rating assembly mounting bolt dynamic static for track rail load rating load rating C C 0 L L M d h Bolt size length m m m. ote : Track rail lengths L are shown in Table.. : Track rail mounting bolts are not appended. exagon socket bolts of JIS B strength division. or equivalent are recoended. Values in parentheses are applicable to the track rail of supplemental code /M of special specification. : The directions of basic dynamic load rating (C, basic static load rating (C 0 and static moment rating (, and are shown in the sketches below. The upper values in the and column apply to one slide unit, and the lower values apply to two units in close contact. Remark : Values in parentheses are applicable to the track rail of supplemental code "/M" of special specification..... 0. 0 0...... M M M 0..... (.. (.. (. M (M M M xample of identification for assembled set code MT G Part code C R 0 0 0 0 00 0 0 00 0 0 0 00 0.. 00....... 00...... 00 MTC MTC SL MT MT SL MTG MTG SL MTC MTC SL MT MT SL MTG MTG SL MTC MTC SL MT MT SL MTG MTG SL Material code Preload symbol Class symbol code Supplemental code T P S /U C, C 0 T0 lange type, MT Length of slide unit C Short o symbol G igh rigidity long,, umber of slide unit (two slide units Length of track rail ( Material o symbol igh carbon steel SL Stainless steel code S specification o on interchangeable symbol specification Preload amount Tc Clearance o symbol T Light preload T Medium preload Special specification A, D,,,, J, L, L, MA, M,, T, U, V,, Z o symbol P SP Accuracy class Ordinary igh Precision Super precision In case ordering track rail only, model code is changed as shown below. Track rail of interchangeable M code L (x: LRPS = 0.0kgf = 0.lbs. = 0.0inch

C-Lube Linear ay M lange type, Short MTC MT igh rigidity longmtg d (L (L -M (L (L -M h MTC(SL L MTC MTC SL Mass (Reference Slide unit kg 0. Track rail kg/m Dimension of Dimension of slide unit Dimension of track rail Recoended Basic Basic Static moment rating assembly mounting bolt dynamic static for track rail load rating load rating C C 0 L L M d h Bolt size length m m m 0 00 MTC MTC SL MT MT SL 0..0 0 0. 0 M0 0 0 M 00 0 MT MT SL MTG MTG SL.0.. 0 000 0 0 0 0 MTG MTG SL MTC MT 0... 00 0.. 0 M0 0 0 M 00 00 00 00 0 00 MTC MT MT... 00 0. M.. 0 M0 00 0 0 00 0 MT ote : Track rail lengths L are shown in Table.. : Track rail mounting bolts are not appended. exagon socket bolts of JIS B strength division. or equivalent are recoended. : The directions of basic dynamic load rating (C, basic static load rating (C 0 and static moment rating (, and are shown in the sketches below. The upper values in the and column apply to one slide unit, and the lower values apply to two units in close contact. C, C 0 T0 xample of identification for assembled set code MT G Part code C R Material code Preload symbol Class symbol code Supplemental code T P S /U lange type, MT Length of slide unit C Short o symbol G igh rigidity long,, umber of slide unit (two slide units Length of track rail ( Material o symbol igh carbon steel SL Stainless steel code S specification o on interchangeable symbol specification Preload amount Tc Clearance o symbol T Light preload T Medium preload Special specification A, D,,,, J, L, L, MA,, T, U, V,, Z o symbol P SP Accuracy class Ordinary igh Precision Super precision In case ordering track rail only, model code is changed as shown below. Track rail of interchangeable M code L (x: LRPS = 0.0kgf = 0.lbs. = 0.0inch

C-Lube Linear ay M Block type, Short MSC MS igh rigidity longmsg (L (L -M depth (L (L -M depth d h MSC(SL L MSC MSC SL Mass (Reference Slide unit kg 0.0 Track rail kg/m Dimension of Dimension of slide unit Dimension of track rail Recoended Basic Basic Static moment rating assembly mounting bolt dynamic static for track rail load rating load rating C C 0 L L M depth d h Bolt size length m m m.... MSC MSC SL MS MS SL 0..... M... (.. (. ( M (M 0... MS MS SL MSG MSG SL 0. 0. 00 00.. MSG MSG SL MSC MSC SL 0.. 0... MSC MSC SL MS MS SL 0.... M... M 0 0.. MS MS SL MSG MSG SL 0.. 0 0 MSG MSG SL MSC MSC SL 0. 0 0.. MSC MSC SL MS MS SL 0..0.. M. M 00 00 00 00 MS MS SL MSG MSG SL 0. 0 0 0 0 MSG MSG SL ote : Track rail lengths L are shown in Table.. : Track rail mounting bolts are not appended. exagon socket bolts of JIS B strength division. or equivalent are recoended. Values in parentheses are applicable to the track rail of supplemental code /M of special specification. : The directions of basic dynamic load rating (C, basic static load rating (C 0 and static moment rating (, and are shown in the sketches below. The upper values in the and column apply to one slide unit, and the lower values apply to two units in close contact. Remark : Values in parentheses are applicable to the track rail of supplemental code "/M" of special specification. xample of identification for assembled set code MS G Part code C R Material code Preload symbol Class symbol code Supplemental code T P S /U C, C 0 T0 Block type, MS Length of slide unit C Short o symbol G igh rigidity long,, umber of slide unit (two slide units Length of track rail ( Material o symbol igh carbon steel SL Stainless steel code S specification o on interchangeable symbol specification Preload amount Tc Clearance o symbol T Light preload T Medium preload Special specification A, D,,,, J, L, L, MA, M,, T, U, V,, Z o symbol P SP Accuracy class Ordinary igh Precision Super precision In case ordering track rail only, model code is changed as shown below. Track rail of interchangeable M code L (x: LRPS = 0.0kgf = 0.lbs. = 0.0inch 0

C-Lube Linear ay M Block type, Short MSC MS igh rigidity longmsg (L (L -M depth (L (L -M depth d h MSC(SL L MSC MSC SL Mass (Reference Slide unit kg 0. Track rail kg/m Dimension of Dimension of slide unit Dimension of track rail Recoended Basic Basic Static moment rating assembly mounting bolt dynamic static for track rail load rating load rating C C 0 L L M depth d h Bolt size length m m m 0 00 MSC MSC SL MS MS SL 0..0 0 0. 0 M 0 M 00 0 MS MS SL MSG MSG SL... 0 000 0 0 0 0 MSG MSG SL MSC MS 0... 0 0 0 0.. 0 M 0 0 M 00 00 00 00 0 00 MSC MS MS.0... M0.. 0 M0 00 0 0 00 0 MS ote : Track rail lengths L are shown in Table.. : Track rail mounting bolts are not appended. exagon socket bolts of JIS B strength division. or equivalent are recoended. : The directions of basic dynamic load rating (C, basic static load rating (C 0 and static moment rating (, and are shown in the sketches below. The upper values in the and column apply to one slide unit, and the lower values apply to two units in close contact. C, C 0 T0 xample of identification for assembled set code MS G Part code C R Material code Preload symbol Class symbol code Supplemental code T P S /U Block type, MS Length of slide unit C Short o symbol G igh rigidity long,, umber of slide unit (two slide units Length of track rail ( Material o symbol igh carbon steel SL Stainless steel code S specification o on interchangeable symbol specification Preload amount Tc Clearance o symbol T Light preload T Medium preload Special specification A, D,,,, J, L, L, MA,, T, U, V,, Z o symbol P SP Accuracy class Ordinary igh Precision Super precision In case ordering track rail only, model code is changed as shown below. Track rail of interchangeable M code L (x: LRPS = 0.0kgf = 0.lbs. = 0.0inch

C-Lube Linear ay M lange type, mounting from bottom M igh rigidity longmg (L (L -d d h L M Mass (Reference Slide unit kg 0. Track rail kg/m. Dimension of slide unit Dimension of track rail Recoended Basic Basic Static moment rating mounting bolt dynamic static for track rail load rating load rating C C 0 L L d d h Bolt size length m m Dimension of assembly...... M 0 0. m. M M MG 0. 0.... 0... M 00 00 00 00 00 00 M MG M MG 0. 0..0.. 0... 0 0. M 0 00 00 0 M MG M MG... 0 0. 0. 0 0 M 0 00 00 0 M MG M MG... 00. 0 0 M 00 00 00 0 00 00 0 0 000 0 M MG M MG.. 0. 0. 00 0 0 0 0.. 0. 0 M 0 0 0 0 000 0 0 0 00 0 00 0 0 M MG ote : Track rail lengths L are shown in Table.. : Track rail mounting bolts are not appended. exagon socket bolts of JIS B strength division. or equivalent are recoended. : The directions of basic dynamic load rating (C, basic static load rating (C 0 and static moment rating (, and are shown in the sketches below. The upper values in the and column apply to one slide unit, and the lower values apply to two units in close contact. xample of identification for assembled set code M G Part code C R Material code Preload symbol Class symbol code Supplemental code T P S /D C, C 0 T0 lange type, M mounting from bottom Length of slide unit o symbol G igh rigidity long,,,,, umber of slide unit (two slide units Length of track rail ( Material o symbol igh carbon steel SL Stainless steel code S specification o on interchangeable symbol specification Preload amount T0 Clearance o symbol T Light preload T Medium preload T eavy preload P SP Special specification A, D,,,, J, L, L, MA, M,, PS, T, V,, Z Accuracy class igh Precision Super precision In case ordering track rail only, model code is changed as shown below. Track rail of interchangeable M code L (x: LRBPS = 0.0kgf = 0.lbs. = 0.0inch

C-Lube Linear ay M lange type, MT igh rigidity longmtg xtra igh rigidity longmtl d d d (L (L -M h MT SL M SL MT SL L Mass Dimension of Dimension of slide unit Dimension of track rail Recoended Basic Basic Static moment rating (Reference assembly mounting bolt dynamic static for track rail load rating load rating Slide Track C C 0 unit rail L L d M d h kg kg/m Bolt size length m m m MT SL 0.0 0. 0.. 0.. M..... 0 M 0...0.. MT SL MSL 0.0 0.. 0.. M.. 0... M 00..... MSL MT MT SL 0.0 0... 0. M 0... M... MT MT SL MT MT SL 0..... M.. M 0 0.. MT MT SL MT 0. 00 00 00 00 MT SL.. M 0... M MTG 0. 00 00. MTG MT MT SL MT 0 00 MT MT SL 0.. 0 MT SL.0.. 0. M 0. M MTG 0. 00 0. MTG MT 0 00 MT MT SL. 0. MT SL MTG.. 0 0 M 00 0 0. M0 0 MTG MTL... 0 00 0 MTL MT. 00 00. 0 MT MTG.. 00 0 M 00 0 00 00 000 M0 0 0 0 MTG MT... 00 0 000 0 0 0 0 00 MT MT. 0 0 0 0 0 0. 0 MT MTG. 0. 0.. 0 M 0 000 0 00 0 00 0 0. 0 M 00 0 0 MTG MTL.0. 0. 000 000 0 00 0 0 MTL ote : Track rail lengths L are shown in Table.. : Track rail mounting bolts are not appended. exagon socket bolts of JIS B strength division. or equivalent are recoended. : The directions of basic dynamic load rating (C, basic static load rating (C 0 and static moment rating (, and are shown in the sketches below. The upper values in the and column apply to one slide unit, and the lower values apply to two units in close contact. xample of identification for assembled set : MTSL, MT0SL, MT MTSL, MTL, MTL, and MTL can be mounted also from bottom direction. code Part code Material code Preload symbol Class symbol code Supplemental code Remark : Oil hole is provided for size and 0 models. MT G C R T P S /D C, C 0 T0 lange type, MT mounting from bottom Length of slide unit igh rigidity long o symbol G L code S specification o on interchangeable symbol specification Special specification A, D,,,, J, L, L, MA, M,, PS, T, V,, Z xtra igh rigidity long Accuracy class Preload amount T0 Clearance P, 0,,,,,,, o symbol SP umber of slide unit (two slide units Material T Light preload o symbol igh carbon steel T Medium preload Length of track rail ( SL Stainless steel T eavy preload igh Precision Super precision In case ordering track rail only, model code is changed as shown below. Track rail of interchangeable M code L (x: LRBPS = 0.0kgf = 0.lbs. = 0.0inch

C-Lube Linear ay M Block type, Short MDC MD igh rigidity longmdg xtra igh rigidity longmtl M depth M depth d MDC,G SL MDC,G0 SL MDC,G SL MD h (L (L (L (L MDCSL L Mass Dimension of Dimension of slide unit Dimension of track rail Recoended Basic Basic Static moment rating (Reference assembly mounting bolt dynamic static for track rail load rating load rating Slide Track C C 0 unit rail L L M depth d h kg kg/m Bolt size length m m m MDC SL 0.00.0 00 0.....0 MDC SL MD SL 0.0 0.. 0. M.... 0 M.. 0..0. MD SL 0 MDG SL 0. 0.0... 0 0... MDG SL MDC 0SL 0.0. 0..... MDC 0SL MD 0SL 0.0 0.... M.. 0.... M. 00... MD 0SL MDG 0SL 0.0...0 0 00. 0 MDG 0SL MDC SL 0.0. 0.... MDC SL MD MD MD SL 0.0 0.... 0 M 0.... M.. MD SL MDG SL 0.. 0.. 0 0 0. MDG SL MD 0..... M 0.. M 0 0.. MD MD 0.. 0 0 00 MD.0... M 0. M MDG 0. 0. 00 0 MDG MD. 0. 0 00 MD MDG.. 0 0. M 0 M 00 0 MDG MDL.. 0 00 0 MDL MD. 0. 00 00 0 MD MDG.. 0 0 0 M 0 M 00 000 00 0 00 0 0 MDG MD.0. 0 00 00 0 000 0 0 0 MD MD. 0. 0 0 0 0 0 0 MD MDG. 0. 0 0. 0. 0 M0. 0 M 00 0 000 0 00 0 0 MDG 0 MDL.. 0 0 000 000 00 0 MDL ote : Track rail lengths L are shown in Table.. : Track rail mounting bolts are not appended. exagon socket bolts of JIS B strength division. or equivalent are recoended. xample of identification for assembled set : The directions of basic dynamic load rating (C, basic static load rating (C 0 and static moment rating (, and are shown in the sketches below. code Part code Material code Preload symbol Class symbol code Supplemental code The upper values in the and column apply to one slide unit, and the lower values apply to two units in close contact. Remark : Oil hole is provided for size to 0 models. MD G C R T P S /D C, C 0 T0 Block type, MD Length of slide unit C Short o symbol G igh rigidity long L xtra igh rigidity long, 0,,,,,, umber of slide unit (two slide units Length of track rail ( Material o symbol igh carbon steel SL Stainless steel code S specification o on interchangeable symbol specification Preload amount T0 Clearance o symbol T Light preload T Medium preload T eavy preload P SP Special specification A, D,,,, J, L, L, MA, M,, PS, T, U, V,, Z Accuracy class igh Precision Super precision In case ordering track rail only, model code is changed as shown below. Track rail of interchangeable M code L (x: LRBPS = 0.0kgf = 0.lbs. = 0.0inch

C-Lube Linear ay M Compact block type, MS igh rigidity longmsg (L (L M depth d h L MS MS SL Mass (Reference Slide unit kg 0. Track rail kg/m. Dimension of Dimension of slide unit Dimension of track rail Recoended Basic Basic Static moment rating assembly mounting bolt dynamic static for track rail load rating load rating C C 0 L L M depth d h Bolt size length m m m... M.. M 0 0.. MS MS SL MS MS SL MSG 0. 0.. 0. M0... M 00 00 00 00 00 00 MS MS SL MSG MS MS SL MSG 0. 0..0... 0.. 0 M. M 0 00 00 0 MS MS SL MSG MS MS MSG SL.00.. 0 0. 0. 0 M 0 M 0 00 00 0 MS MS MSG SL ote : Track rail lengths L are shown in Table.. : Track rail mounting bolts are not appended. exagon socket bolts of JIS B strength division. or equivalent are recoended. : The directions of basic dynamic load rating (C, basic static load rating (C 0 and static moment rating (, and are shown in the sketches below. The upper values in the and column apply to one slide unit, and the lower values apply to two units in close contact. C, C 0 T0 xample of identification for assembled set code MS G Part code C R Material code Preload symbol Class symbol code Supplemental code T P S /D Compact block type, MS Length of slide unit o symbol G igh rigidity long,,, umber of slide unit (two slide units Length of track rail ( Material o symbol igh carbon steel SL Stainless steel code S specification o on interchangeable symbol specification Preload amount o symbol T Light preload T Medium preload T eavy preload P SP Special specification A, D,,,, J, L, L, MA, M,, PS, T, U, V,, Z Accuracy class igh Precision Super precision In case ordering track rail only, model code is changed as shown below. Track rail of interchangeable M code L (x: LRBPS = 0.0kgf = 0.lbs. = 0.0inch

C-Lube Linear ay MUL Miniature type MUL -M depth Oil hole (L d h L Mass (Reference g Slide unit Track rail (per 00 Dimension of Dimension of slide unit Dimension of track rail Recoended Basic Basic Static moment rating assembly mounting bolt dynamic static for track rail load rating load rating C C 0 L M depth d h Bolt size length m m m MUL. M........ Cross-recessed head screw for precision equipment M. 0. 0....0 MUL MUL.. M...... exagon socket head bolt M. 0 0..... MUL ote : Track rail lengths L are shown in Table.. : Track rail mounting bolts are not appended. In case recoended bolts are required, please indicate /MA onto the identification. : The directions of basic dynamic load rating (C, basic static load rating (C 0 and static moment rating (, and are shown in the sketches below. The upper values in the and column apply to one slide unit, and the lower values apply to two units in close contact. C, C 0 T0 xample of identification for assembled set code MUL Part code Preload symbol Class symbol Supplemental code C R0 T /U MUL, umber of slide unit (two slide units Length of track rail (0 Special specification, LR, MA, U, Accuracy class o symbol Ordinary igh Preload amount o symbol T Light preload = 0.0kgf = 0.lbs. = 0.0inch