Chemical Hygiene Plan

Chemical Hygiene Plan I. Policy The purpose of the Chemical Hygiene Plan (CHP) is to outline laboratory work practices and procedures which are necessary to ensure that members of the university community are protected from health hazards associated with chemicals with which they work. II. Authority The Chemical Hygiene Plan, required to comply with provisions of CCR Title 8 5191 et al: A. Standard Operating Procedures relevant to safety and health considerations to be followed when laboratory work involves the use of hazardous chemicals CCR Title 8 5191(b)(2)(e) B. Criteria that the university will use to determine and implement control measures to reduce laboratory worker exposures to hazardous chemicals including engineering controls, the use of personnel protective equipment and hygiene practices. C. A requirement that fume hoods and other protective equipment are functioning properly D. Provisions for laboratory worker information and training E. The circumstances under which a particular laboratory operation, procedure or activity shall require prior approval from the Principal Investigator or course or laboratory instructor before implementation F. Provisions for medical consultation and medical examination G. Designation of personnel responsible for implementation of the Chemical Hygiene Plan, including the assignment of a Chemical Hygiene Officer H. Provisions for additional laboratory worker protection for work with particularly hazardous substances

III. Scope The California Code of Regulations (CCR) Title 8 5191 defines a laboratory as a facility where laboratory use of hazardous chemicals occurs. It is a workplace where relatively small quantities of hazardous chemicals are used on a nonproduction basis, and is a facility which meets the following conditions: A. Multiple chemical procedures or chemicals are used; B. The procedures are not, and do not simulate, production processes; C. Chemical manipulations are performed; D. The potential for laboratory worker exposure to hazardous chemicals is minimized by the use of protective laboratory practices and equipment. CCR Title 8 5191 defines a hazardous chemical for which there is statistically significant evidence, based on at least one study conducted in accordance with established scientific principles that acute or chronic health effects may occur in exposed employees. The term health hazard includes chemicals which are carcinogens, toxic or highly toxic agents, reproductive toxins, irritants, corrosives, sensitizers, hepatotoxins, nephrotoxins, neurotoxins, agents which action on the haematopoietic systems, and agents which damage the lungs, skins, eyes, or mucous membranes. Each laboratory will develop all procedures necessary to protect laboratory worker health and safety. The following chapters provide a recommended set of minimum procedures and guidelines for protecting persons working in a laboratory environment, and may assist individual laboratories in developing laboratory-specific standard operating procedures. The California Code of Regulations (CCR) Title 8 5191 defines a laboratory as a facility where laboratory use of hazardous chemicals occurs. It is a workplace where relatively small quantities of hazardous chemicals are used on a nonproduction basis, and is a facility which meets the following conditions: A. Multiple chemical procedures or chemicals are used; B. The procedures are not, and do not simulate, production processes; C. Chemical manipulations are performed; D. The potential for laboratory worker exposure to hazardous chemicals is minimized by the use of protective laboratory practices and equipment. CCR Title 8 5191 defines a hazardous chemical for which there is statistically significant evidence, based on at least one study conducted in accordance with established scientific principles that acute or chronic health effects may occur in exposed employees. The term health hazard includes chemicals which are carcinogens, toxic or highly toxic agents, reproductive toxins, irritants, corrosives, sensitizers, hepatotoxins, nephrotoxins, neurotoxins, agents which action on the

haemopoietic systems, and agents which damage the lungs, skins, eyes, or mucous membranes. Each laboratory will develop all procedures necessary to protect laboratory worker health and safety. The following chapters provide a recommended set of minimum procedures and guidelines for protecting persons working in a laboratory environment, and may assist individual laboratories in developing laboratory-specific standard operating procedures. For the purpose of this manual, a laboratory worker could mean a Principal Investigator, course or laboratory instructor, faculty member, technician, laboratory assistant, teaching assistant, research assistant or student. IV. Definitions ANSI American National Standards Institute CCR California Code of Regulations CHP Chemical Hygiene Plan Cal-OSHA California EPA Federal Environmental Protection Agency NFPA National Fire Protection Association OSHA Federal Occupational Health and Safety Administration PEL Permissible Exposure Limit V. Accountability California State University Fullerton A. Keep records of laboratory worker exposures to hazardous chemicals including measurements made to monitor exposures, medical consultation and examination and written opinions; B. Provide laboratory workers with general training and information regarding chemical and physical hazards; C. Provide laboratory workers with access to medical consultation and examinations at no cost if a laboratory worker develops signs or symptoms of exposure or if an action level or PEL is routinely exceeded (see f), or if there is a spill, leak, or explosion that makes laboratory worker exposure likely;

D. Provide laboratory workers with respirators when necessary; E. Make MSDS's accessible to laboratory workers; F. Measure the concentration of the chemical in the air, if there is reason to believe that an action level or PEL has been exceeded for any chemical for which a substance-specific standard has been established; G. Notify all laboratory workers of the results of the measurements and implement procedures to lower the level below the PEL or action level, if the level measured is greater than the PEL or action level; H. Identify and establish "Controlled Work Area(s)" in the laboratory for work with select carcinogens, reproductive toxins, or acute toxins that are very highly toxic. Chemical Hygiene Officer, Environmental Health and Safety Office A. Chemical Hygiene Officer develops and updates the Chemical Hygiene Plan and appropriate policies and practices; B. Chemical Hygiene Officer provides technical assistance in complying with the Chemical Hygiene Plan and answers safety questions for laboratory workers; C. Chemical Hygiene Officer assists Principal Investigators/Course Instructors in developing appropriate safety precautions for new projects and procedures; D. Monitors procurement of new chemicals; E. Monitors collection and disposal of spent and hazardous chemical wastes; F. Keeps current on federal, state and local legislation and regulations concerning chemicals; G. Chemical Hygiene Officer ensures that laboratory workers comply with the Chemical Hygiene Plan; H. Ensures that appropriate personal protective equipment is available as needed; I. Monitors proper functioning of protective equipment such as fume hoods and arranges for prompt repairs as needed; J. Chemical Hygiene Officer performs regular chemical hygiene and housekeeping inspections; K. Performs routine inspections of emergency equipment;

L. Gathers and maintains manufacturers' Material Safety Data Sheets, and assures that the current web-based Materials Safety Data Sheet site(s) are established and operable on the Desktop of at least one laboratory computer; M. Assists in the development and implementation of a labeling program for chemicals; N. Assists in determining when a complaint of possible over-exposure is "reasonable" and should be referred for medical consultation; O. Assists in determining when an "Exposure Assessment" is appropriate; P. Assists in conducting "Exposure Assessments;" Q. Chemical Hygiene Officer reviews chemical inventory to determine which chemicals are carcinogens as designated in CCR General Industry Safety Orders Group 16; Control of Hazardous Substances; Article 110. Regulated Carcinogens 5209; R. Environmental Health and Safety Office maintains campus' chemical inventory. Principal Investigator, Course or Laboratory Instructor The Supervisor's duties, as defined in the Cal-OSHA Laboratory Standard and the Chemical Hygiene Plan, are the responsibility of the Principal Investigator. For laboratories with no Principal Investigator, the Supervisor's duties are assumed by the person with authority over all laboratory functions, such as course or laboratory instructor. The primary responsibility of the supervisor is to institute the Chemical Hygiene Plan and ensure compliance with the Cal-OSHA Laboratory Standard within their respective laboratories. The duties include the following: A. Ensure that all work is conducted in accordance with the Chemical Hygiene Plan; B. Define the location of "Controlled Work Areas" where toxic substances and potential carcinogens will be used, and ensure that the inventory of these substances is properly maintained; C. Obtain, review, and approve standard operating procedures, detailing all aspects of proposed research activities that involve hazardous agents;

D. Prepare a Standard Operating Procedure (S.O.P.) for every experimental procedure. The S.O.P. shall include a description of any alternate procedure and an assessment of alternate controls that could be used; E. Define hazardous operations, designating safe practices, and selecting protective equipment; F. Ensure that laboratory workers receive instructions and training in safe work practices, use of personal protective equipment, and in procedures for dealing with accidents involving toxic substances; also training specific to hazards in those areas supervised by them. G. Ensure that all personnel obtain the medical examinations and protective equipment necessary for the safe performance of their job; H. Monitor the safety performance of laboratory workers to ensure the required safety practices and techniques are being employed; I. Arrange with Chemical Hygiene Officer or Environmental Health and Safety Office for workplace air samples, swipes, or other tests to determine the amount and nature of airborne and/or surface contamination, inform employees of the results, and use data to aid in the evaluation and maintenance of appropriate laboratory conditions; J. Assist the Chemical Hygiene Officer, Radiation Safety Officer and Biohazard Safety Officer and Environmental Health & Safety personnel when necessary; K. Conduct informal laboratory inspections on a timely basis consistent with the type or degree of hazard to ensure compliance with existing laboratory S.O.P.'s; L. Prepare emergency procedures for dealing with accidents that may result in the unexpected exposure of personnel, or the environment, to a toxic substance; M. Investigate accidents and report them to the Chemical Hygiene Officer. Include procedures that will minimize the repetition of that type of accident; N. Report to the Chemical Hygiene Officer incidents that (1) cause personnel to be seriously exposed to hazardous chemicals or materials, such as through skin penetration, ingestion of a chemical, or probable inhalation of a chemical, or that (2) constitute a danger of environmental contamination; O. Ensure that action is taken to correct work practices and conditions that may result in the release of toxic chemicals;

P. Ensure proper disposal of unwanted and/or hazardous chemicals and materials through appropriate office; Q. Document and maintain compliance with all local, state, and federal regulatory requirements; R. Make copies of the approved safety plan available to the laboratory staff; S. Performs regular chemical hygiene and housekeeping inspections; T. Develops and implements a labeling program within the laboratory. Technicians, Laboratory Assistants, Teaching Assistants, Students A. Understand and comply with the procedures outlined in the Chemical Hygiene Plan; B. Understand and comply with all Standard Operating Procedures; C. Understand and comply with all training received; D. Understand the function and proper use of all personal protective equipment. Wear personal protective equipment when mandated or necessary. E. Report, in writing, to your Principal Investigator/Course or Laboratory Instructor of any significant problems arising from the implementation of the Standard Operating Procedures; F. Report to your Principal Investigator/Course or Laboratory Instructor all facts pertaining to every accident that results in the exposure to toxic chemicals, and any action or condition that may exist that could result in any accident; G. Contact your Principal Investigator/Course or Laboratory Instructor, and/or the Chemical Hygiene Officer if any of the above procedures are not clearly understood. Responsibilities of All Personnel Using Hazardous Chemicals Each person working with or around chemicals, having been trained, is responsible for remaining aware of the hazards of those materials and handling those chemicals in a safe manner. Each person is responsible for knowing how to handle a hazardous chemical safely according to its types of hazards. If that person is unsure of a hazard or safety procedure, ASK UNTIL YOU KNOW FOR SURE! Everyone shares the responsibility to ensure that all containers of chemicals are properly labeled with the identity of the chemical and its hazards.

REMEMBER: NO AMOUNT OF INSURANCE CAN CURE BLINDNESS OR RESURRECT THE DEAD! SO BE RESPONSIBLE FOR YOUR OWN WELL-BEING. Lab Visitors Visitors to research labs must be supervised at all times. Entry of visitors will not be allowed during operations with hazardous materials or equipment. Children under the age of 18 are not allowed in any of the research labs. Exceptions to this are participants in special programs which have prior approval from the Department Chair and require advance notification of the Chemical Hygiene Officer. VI. Program There are three important attitudes to assume while working: BE AWARE BE PREPARED BE PROTECTED Know the hazards before you begin your experiment. At minimum, read the label and Material Safety Data Sheet. Answer the following questions: What's the worst thing that can go wrong? What should I do to be prepared for it? Know the practices and equipment that can minimize your exposure to the hazards of your work? General Safety Guidelines: A. Working alone is fundamentally unsafe. Someone should be working with you. If the "buddy system" is not possible then someone should be aware of the solitary worker and check on him/her at regular intervals; B. Wear appropriate eye protection at all times. Contact lenses can absorb chemicals and trap them against your eyes. Glasses, not contact lenses should be worn; however, normal prescription glasses are not protective eye wear; C. When working with flammable chemicals, be certain there are no sources of ignition near enough to cause a fire or explosion in the event of a vapor release or liquid spill; D. Use shields for protection whenever an explosion or implosion might occur; E. Don't underestimate the risks of materials you use. Find out the facts, and protect yourself. Be aware of the chemical hazards, as determined from the MSDS and other appropriate references;

F. Use proper protective equipment every time you use the materials. Make sure the equipment is not damaged and that you know how to use it; G. Know the location, and proper use of emergency equipment, and be familiar with procedures. Clean up spills immediately. Emergency Response Procedures should be posted next to the telephone in each laboratory; H. Don't use equipment unless you know how to use it properly, and use it only for its intended purpose; I. Minimize all chemical exposures. Avoid all skin contact with chemicals. Wear gloves appropriate for the material; J. Assume a mixture (or substance of unknown toxicity) is more hazardous than its components; K. Keep chemicals in labeled containers; L. Use chemicals in a chemical fume hood, and know how to use the hood properly. Never use highly toxic agents, carcinogens, or reproductive toxins outside the hood. The room and hood should be labeled as a "Controlled Work Area" if these chemicals are in use; M. Your ventilation system will work more efficiently with the laboratory doors closed; N. Dispose of cracked or broken glassware immediately. Lubricate glassware with water or glycerol when appropriate, such as when fitting glass tubing through a rubber stopper. Protect your hands with a towel when inserting or attaching glassware; O. Unattended Operations; An experiment is unattended if there is no one immediately present who fully understands the operation and shutdown procedure to be taken in the event of an emergency. These circumstances require special precautions: 1. Unattended procedures that could result in fire or explosion should be equipped with the necessary automatic shutdown control. Examples of mishaps that can occur during unattended operations include loss of cooling water, overheating, flooding, etc; 2. Post warning signs for radioactive, chemical, biological, flammable, reactive, explosive hazards, and any other hazards; 3. Use necessary shields and barriers to contain splashes, explosions, or other releases;

4. Leave lights on and doors closed and locked while absent; Personal Hygiene 5. Be aware that as the need for water for cooling decreases late in the day or at night, water surges may result because of excess water pressure in the few areas that are using it. A. In the event of skin contact with a chemical rinse the affected area with a neutralizing solution in the case of contact with a strong acid or caustic and/or with copious amounts of water; B. When handling chemicals used appropriate fume hoods to avoid inhalation of chemicals; do not smell or taste chemicals, for identification; C. NEVER mouth pipette anything, or use mouth suction to start a siphon; D. Always wash your hands with soap and water just before leaving the laboratory, and wash your face prior to eating, drinking, smoking, using the restroom, applying cosmetics, or inserting contact lenses; E. Never eat, drink, smoke, chew gum, bite fingernails, apply cosmetics, or insert contact lenses in a laboratory, and, once removed from the laboratory, only after you have washed your hands; F. Never bring food, cigarettes, chewing gum, beverages, or food containers into a laboratory. They can absorb chemicals; G. Never store food in refrigerators/freezers that are approved for chemical, radiation, or biohazards use. Protective Clothing and Equipment A. Eye protection worn when working with chemicals should meet the requirements of ANSI; B. Eye protection should include a face shield when the chemical hazard warrants it; C. When working with corrosive liquids, wear gloves made of a material that is resistant to permeation by the corrosive chemical (use manufacturer s published permeation chart). Test the glove by air inflation (do not inflate by mouth) for the absence of pin-hole leaks; D. When working with corrosive chemicals, wear a rubberized laboratory apron;

E. Lab coats should be worn and buttoned at all times while in the laboratory. The lab coat should be removed when you leave the laboratory and, immediately, if it becomes contaminated; F. Protect your skin and feet with adequate clothing and footwear. Shorts or short skirts should not be worn in the laboratory without a lab coat. Opentoed shoes or sandals, or shoes without firm footing shall not be worn in the laboratory; appropriate footwear shall protect the whole foot. G. Remove protective clothing when you leave the laboratory; H. Confine hair and loose clothing while in the laboratory; I. When working with allergenic, sensitizing, or toxic chemicals, wear gloves made of material known to be or tested and found to be resistant to permeation by the chemical and tested for the absence of pin holes; J. Whenever exposure by inhalation is likely to exceed the threshold limits described in MSDS's, use a fume hood. If this is not possible, a proper respirator must be worn. You must be appropriately trained and fit tested to wear a respirator. To become certified to wear a respirator contact the Environmental Health and Safety Department at 657-278-7233; K. Carefully inspect all protective equipment before using. Do not use defective equipment. Housekeeping A. Clear access MUST be available to ALL emergency equipment, eye washes, safety showers, fire extinguishers, circuit breakers, fire pull boxes, emergency spill equipment and exits should never be blocked by anything, not even a temporarily parked cart; B. All chemical containers must be labeled with at least the identity of the contents and the hazards those contents present to users; C. Keep all work areas, especially laboratory benches, clear of clutter; D. Keep all aisles, hallways, exits, and stairs clear of all chemicals; E. All chemicals should be placed in their assigned storage areas at the end of each workday; F. At the end of each workday, the contents of all unlabeled containers are to be considered as either spent chemical material and will be classified by the CHO as a waste based on qualitative testing performed in the Chemical Storage

Area or a hazardous waste based on knowledge of the PI, graduate student/undergraduate student; G. Spent or chemical waste material should be properly labeled and kept in their proper containers; H. Promptly clean up all spills; properly dispose of the spilled chemicals and clean up all materials; I. All working surfaces and floors should be cleaned regularly. Bench tops should be cleaned at the end of a particular operation or experiment or at the end of each workday; J. No chemicals are to be stored in aisles or stairwells, on desks or laboratory benches, on floors or in hallways; K. Extraneous materials should not be stored in a fume hood because it can interfere with the air flow and jeopardize the safe operation of the hood; L. Chemicals should be stored in an Earthquake Safe manner: in closed cabinets or on lipped or retaining wired shelves. Prior Approval Each laboratory Principal Investigator/Course or Laboratory Instructor should identify activities which (due to potential hazard) require prior approval by them or safety personnel and should inform technicians, laboratory assistants, teaching assistants, researchers, and students of the necessary approval procedures. The Environmental Health and Safety Department can assist as a resource providing information to help minimize hazards and identify activities which require prior approval. The following guidelines are offered to assist in that decision making process: Prior approval needs to be considered when: A. There is a new procedure, process or test, even if it is very similar to older practices; B. It is likely that toxic limit concentrations could be exceeded or that other harm is likely; C. There is a change in a procedure, process or test, even if it is very similar to older practices. "Change in a procedures, process or test" means: 1. There is a substantial increase or decrease in the amount of one or more chemicals used;

2. There is a substitution or deletion of any of the chemicals in a procedure; 3. There is any change in other conditions under which the procedure is being conducted; D. There is a change in location of the procedure, process, or test; E. There is a failure of any of the equipment used in the process, especially of safeguards such as fume hoods, power supplies, or clamp apparatus; F. There are unexpected results; Members of the laboratory staff become ill, suspect that they or others have been exposed, or otherwise suspect a failure of any safeguards. Any new procedures should be subjected to considerable review. Not only from a scientific standpoint, but also to assure that are all safety considerations in place prior to implementation. Spills and Accidents Spills of toxic substances or accidents involving any hazardous chemical or substance should be resolved quickly according to the Emergency Response Procedures and the following Spills Accident Procedures. Always notify your supervisor and appropriate emergency personnel immediately. CHEMICAL SPILL Notes and Precautions: The range and quantity of hazardous chemicals used in laboratories require preplanning to respond safely to chemical spills. The cleanup of a chemical spill should only be done by knowledgeable and experienced personnel. Spill cleanup instructions are available in the Environmental Health and Safety Department. A minor chemical spill is one that the laboratory staff is capable of handling safely without the assistance of safety and emergency personnel. All other chemical spills are considered major. Minor Chemical Spill» Alert people in immediate area of spill.» Call Environmental Health and Safety Department at 657-278-7233. After hours, dial 911.» Wear protective equipment, including safety goggles, gloves, and long- sleeve lab coat.

» Avoid breathing vapors from spill.» Confine spill to small area.» Neutralize or absorb the spilled chemical with the proper spill cleanup materials. Collect residue, place in container, and dispose of it in accordance with hazardous waste procedures.» Clean spill area with water. Major Chemical Spill» Attend to injured or contaminated persons and remove them from exposure, if you can do so safely without endangering yourself.» Alert people in the laboratory to evacuate.» If spilled materials is flammable, turn off ignition and heat sources.» Call Environmental Health and Safety Department at 657-278-7233. After hours dial 911.» Close doors to affected area.» Have person knowledgeable of incident and laboratory assist emergency personnel. BIOLOGICAL SPILL Note and Precautions: Biological spills can generate aerosols that can be dispersed in the air throughout the laboratory. These spills are very serious if they involve microorganisms that require Biosafety Level (BL) 3 containment, since most of these agents have the potential for transmitting disease by infectious aerosols. To reduce the risk of inhalation exposure in such an incident, occupants should hold their breath and leave the laboratory immediately. The laboratory should not be reentered to decontaminate and clean up the spill for at least 30 minutes. Appropriate protective equipment is particularly important in decontaminating spills involving microorganisms. This equipment includes lab coat with long-sleeves, disposable gloves, disposable shoe covers, if appropriate, and safety goggles and mask. Use of this equipment will prevent contact with contaminated surfaces and protect mucous membranes from exposure to splattered materials. For further precautions involving biohazards, refer to Biosafety Manual available from Environmental Health and Department.

Spill Involving a Microorganism Requiring Biosafety Level 1 Containment 1. Wear disposable gloves. 2. Soak paper towels in disinfectant and place over spill area. 3. Place towels in plastic bag for disposal. 4. Clean spill area with fresh towels soaked in disinfectant. Spill Involving a Microorganism Requiring Biosafety Level 2 Containment 1. Alert people in immediate area of spill. 2. Put on protective equipment. 3. Cover spill with paper towels or other absorbent materials. 4. Carefully pour a freshly prepared 1 in 10 dilution of household bleach around the edges of the spill and then into the spill. Avoid splashing. 5. Allow a 20-minute contact period. 6. Use paper towels to wipe up the spill, working from the edges into the center. 1. Clean spill area with fresh towels soaked in disinfectant. 2. Place towels in a plastic bag and decontaminate in an autoclave. Spill Involving an Unknown Microorganism 1. Attend to injured or contaminated persons and remove them from exposure, if you can do so safely without endangering yourself. 2. Alert people in the laboratory to evacuate. 3. Close doors to affected area. 4. Call Environmental Health and Department at 657-278-7233, or after hours dial 911. 5. Have person knowledgeable of incident and laboratory assist emergency personnel. RADIATION SPILL Notes and Precautions: Spreading of radiation beyond the spill area can easily occur by the movement of personnel involved in the spill or cleanup effort. Prevent spread by confining movement of personnel until they have been monitored and found free of contamination. A minor radiation spill can be managed by laboratory personnel/staff. The Radiation Safety Officer and EHIS must be notified for all radiation spills.

Minor Radiation Spill 1. Alert people in immediate area of spill. 2. Immediately notify the Radiation Safety Officer. 3. Wear protective equipment, including safety goggles, disposable gloves, shoe covers, and long-sleeve lab coat. 4. Place absorbent paper towels over liquid spill. Place towels dampened with water over spills of solid materials. 5. Using forceps, place towels in plastic bag. Dispose in radiation waste containers. 6. Monitor area, hands, and shoes for contamination with an appropriate survey meter or method. Repeat cleanup until contamination is no longer detected. Major Radiation Spill or any isotope of Iodine Spill 1. Attend to injured or contaminated persons and remove them from exposure if you can do so safely without endangering yourself. 2. Alert people in the laboratory to evacuate. 3. Have potentially contaminated personnel stay in one area until they have been monitored and shown to be free of contamination. 4. Call the Environmental Health and Safety Department at 657-278-7233, or after hours dial 911. 5. Close doors and prevent entrance into affected area. 6. Have person knowledgeable of incident and laboratory assist emergency personnel. Spent/Hazardous Waste Chemical Guidelines A. Spent/Waste Chemical Disposal Procedures 1. Whenever possible, the container of the original material should be used for the spent/waste chemical material; (Exception: can with plastic pour spouts.) 2. The outside of the container must be completely clean; 3. Containers must have a screw cap or lid which is leak-proof. Secure loose screw tops with strong tape. Do not use caps of foil, corks, or glass stoppers; 4. Give special attention to containers of carcinogens, mutagens, and teratogens: Tape all caps, and double-bag and seal in airtight plastic; 5. Store corrosives in glass containers; (Exception: hydrofluoric acid and other glass-reactive chemicals, such as potassium hydroxide and sodium hydroxide.)

6. Do not mix acids; 7. Store flammable and other spent/waste solvents in either glass containers or nonmetallic safety disposal containers; 8. Halogenated and non-halogenated compounds must be separated from one another; 9. Whenever possible, do not dispose of spent or waste chemicals in partially-filled containers. Disposal costs are based on the size of the container or drum, not the contents; 10. Refer to Environmental Health and Safety Department and the Appendix for information on chemical incompatibility. Segregate incompatible spent chemicals/waste to prevent accidental combinations; 11. Spent/Waste chemicals will be collected only if the containers have been properly sealed and labeled. Label containers with the CHEMICAL NAME, not structure, formula, or an abbreviation. 12. Identify mixtures (for every component) by percent or volume composition; 13. Completely remove, cross-out, or cover over any chemical information that does not pertain to the spent chemical/waste chemical in the container; 14. Carefully label all chemicals in use to reduce generating unknown waste. Disposal of unknown waste requires extensive laboratory testing, which is very expensive; 15. To obtain more information, or to request pick-up of spent chemical or hazardous waste contact Environmental Health and Safety Department extension 7233. B. Guidelines For Waste Reduction Plan a procedure to collect spent hazardous chemicals for disposal before you start on a project. Properly label each collection container with the name of each chemicals placed into the container. It is the responsibility of each department, group, or experimenter to identify the spent chemical/hazardous waste chemical properly before disposal; inadvertent mixing of incompatible chemicals could have serious consequences.

Protection of the environment makes the disposal of large quantities of hazardous chemical liquids and solids a costly problem. It is in everyone's best interest to keep quantities of chemical waste to a minimum. The following suggestions may help: 1. Order only the amount of chemical you need for your project or experiment even if you can get twice as much for the same money; 2. Use only the amount of chemicals that are needed for conclusive results; 3. Avoid long term storage ( > 1 year) of excess chemical, particularly if it is an extremely toxic or flammable chemical, just because you may want it in the future; 4. Before disposing of unwanted, unopened, uncontaminated chemicals, check with others in your department who may be able to use them; 5. On termination of a research project or completion of a thesis, all unused chemicals to be kept by the laboratory must be labeled; 6. Make sure all samples and products to be disposed of are properly identified, labeled with its chemical name and placed in correct containers. Do not leave them for others to clean up after you. Receipt, Check-In, and Delivery/Transportation of Hazardous Materials or Chemicals Serious accidents may occur if hazardous chemicals, etiological (disease-causing) agents, radioactive materials, carcinogens, compressed gas cylinders. and other materials are not handled, transported and shipped in accordance with safe practices. Checking-in Hazardous Materials or Chemicals The most important aspect of checking-in hazardous materials or chemicals should be to verify that the integrity of the container(s) is intact. I. Shipping Container(s) Make sure the outside shipping container(s) (cardboard, wood, metal cans, etc.) has not been damaged. Check for stains resulting from leakage inside. Check for evidence of crushing that might damage the hazardous material or chemical container(s) inside. Note any unusual odors that could indicate leakage.

II. Packing Material(s) Check inside packing material(s) (secondary cardboard containers, plastic bags or wrapping, vermiculite, etc.) to make sure that they are intact. Check for tears in the plastic. Check for leakage or odors in the vermiculite. Examine secondary container(s) for damage. Check for stains resulting from leakage inside. III. Hazardous Materials or Chemical Container(s) Check the hazardous material or chemical container(s) (glass bottle or jar, plastic bottle or jar, can, etc.) for breakage or cracks. Check the cap for cracks, deterioration, or dried or wet residue. Check for unusual odors. Make sure the hazardous material or chemical container(s) are not damaged in any way. If any evidence of damage, breakage, leakage, etc. is found, isolate the shipping container(s), preferably in a fume hood if available, then call Environmental Health and Safety Department for assistance at extension 657-278-7233 (x. 7233). Transporting Hazardous Materials Guidelines have been developed regarding the transport of hazardous chemicals such as acids and corrosive liquids, flammable solids and liquids, toxic chemicals, oxidizers and reactive chemicals, (including spent chemical and hazardous waste) from one room to another within a building or from building to building. The guides require: (1) using a proper container, (2) utilizing a proper transporting device, or (3) limiting the size and quantity transported. Other hazardous chemicals, such as compressed gas cylinders, biohazards, radioactive materials, carcinogenic compounds, etc., require special precautions. D.O.T. shipping boxes are available from EHIS at extension 7233 for safe transporting of hazardous materials. I. Glass Bottles A. The transport of large glass bottles (one gallon or larger) by hand shall be done in a proper carrier. Acceptable carriers include a plastic acid or bottle carrier, styrofoam casing, or appropriate cardboard box, wooden crate, etc. In general, depending on the hazard, a single glass bottle of one quart or less may be carried by hand, except inside an elevator (see 1.). B. Whenever more than one glass bottle of any size is being transported, it is necessary that measures be taken to prevent the glass bottles from contacting each other. Such devices as cardboard boxes with dividers,

styrofoam cases with compartments, or the use of a vermiculite filler is appropriate. C. If a cart is employed to transport glass bottles within a building, precaution must be taken to prevent the glass bottles from contacting each other and/or falling off the cart. Glass bottles shall not be placed loosely on a cart unless the cart is specially designed to accommodate the bottles, or the bottles are in protective containers, such as described above. The cart shall have an adequate lip to prevent packages from slipping off the cart. D. Anytime glass bottles are to be transported from building to building, additional precaution must be taken. The cart used should have larger wheels (4" minimum), preferable of a pneumatic type. The cart should have at least a 3" lip and all bottles should be transported in some type of protective container, such as described above. E. Transport within elevators always requires an acceptable carrier as described above. II. Plastic Coated Bottles/Metal Cans/Safety Cans A. The hand-carrying of these kinds of containers is permitted since the integrity of the container is far superior to that of the glass bottle. If any of these containers are involved in an accident, it is not likely that the entire contents of the container would be immediately spilled or splashed about. There also would be little or no glass fragments. B. Whenever more than two of these containers are being transported, an additional carrying device, such as an appropriate cardboard box or a wheeled cart with a lip should be employed. Follow the precaution given for the type of cart as outlined above. III. Cardboard Cartons, Crates, Boxes Containing Chemicals Bottles When transporting chemicals in their original shipping packages, normal transporting methods may be used, such as push carts and dollies. If these containers must be transported on outdoor paths, the precautions listed above for bottles shall be followed, unless the packages can be adequately secured to the cart or the dolly. IV. Chemical Ordering Do's and Don'ts A. When available, order chemicals in plastic coated bottles. B. When available, order flammable liquids in MCB SAF-T-CAN (glass bottles inside metal can).

C. Do not order more of one chemical than you will utilize in normal operations. Overstocking to save money on large quantities creates many other problems, such as exceeding the permissible amount of flammable liquids in a lab, or increasing the possibility of the chemicals getting old before they are consumed. Old chemicals may become hazardous due to aging, and disposal is always costly. If the overstock is not used it will likely have to be shipped off as waste at extra cost to the campus. V. Biohazard Transport Transport of biohazards to other labs or facilities requires suitable enclosed containers. Contact Environmental Health and Safety Department for assistance if a biohazard (or suspected biohazard) is delivered to your area. VI. Cylinder Transport Whenever compressed gas cylinders are moved, caps must be placed over the valves and suitable carts with securing devices used. Cylinders have to be secured to the bench or wall of labs at all times. Free-standing cylinders, or cylinders moved without a cart, may become "unguided missiles" if they fall and the valve stem is broken. VII. Transporting of Radioactive Materials Transportation of all radioactive materials/waste must be performed under the supervision of the Radiation Safety Officer. Contact the Environmental Health and Safety Department for assistance at 657-278- 7233 (x. 7233). VIII. Transport of Chemical Carcinogens Personnel utilizing carcinogens or suspect carcinogens should be aware of the hazards involved in transporting these chemicals. The risk can be reduced by using sealed containers, such as plastic bags which are large enough to contain the material if spillage or breakage occurs. The sealed bags shall then be placed in an airtight can, such as a paint can. A warning label shall identify the substance, its carcinogenicity (use "Caution -- Cancer Suspect Agent"), and the quantity, with the researcher's name and department. This procedure is the NCI recommended practice not only for transport, but also for storage of such materials. Please refer to Chemical Hygiene Plan for more information on proper handling and storage of carcinogens.

IX. Finally, never utilize a private vehicle for transporting a hazardous materials. Always consult Environmental Health and Safety Department if in doubt as to safe procedures.

IV. Protocol-Specific Safety Procedures All laboratory procedures must contain a description of specific safety practices which have been prepared by a Principal Investigator or Laboratory/Course Instructor and incorporates the applicable precautions described in this section. Laboratory workers should read and understand these practices before commencing a procedure. No amount of written precautions can substitute for procedure specific advice from your Principal Investigator, laboratory or course instructor. Therefore, before starting a procedure always meet with your supervisor. Procedures for Toxic Chemicals The MSDS's for many of the chemicals used in the laboratory will state recommended limit or OSHA-mandated limits, or both, as guidelines for exposure. Typical limits are threshold limits values (TLV), permissible exposure limit (PEL), and action levels. When such limits are stated, they will be used to assist the Chemical Hygiene Officer in determining the safety precautions, control measures, and safety apparel that apply when working with toxic chemicals. A. When a TLV or PEL value is less than 50 ppm or 100 mg/m 3, the user of the chemical must use it in an operating fume hood, glove box, vacuum line, or similar device, which is equipped with appropriate traps and/or scrubbers. If none are available, no work should be performed using that chemical; B. If a TLV, PEL, or comparable value is not available for that substance, the animal or human median inhalation lethal concentration information, LC 50, will be assessed. If that value is less than 200 ppm or 2000 mg\m 3 (when administered continuously for one hour or less), then the chemical must be used in an operating fume hood, glove box, vacuum line or similar device, which is equipped with appropriate traps and/or scrubbers. If none are available, no work should be performed using that chemical; C. Whenever laboratory handling of toxic substances with moderate or greater vapor pressures will be likely to exceed air concentration limits, laboratory work with such liquids and solids will be conducted in a fume hood, glove box, vacuum line, or similar device, which is equipped with appropriate traps and/or scrubbers. If none are available, no work should be performed using that chemical. Procedures for Flammable Chemicals In general, the flammability of a chemical is determined by its flash point, the lowest temperature at which an ignition source can cause the chemical to ignite momentarily under certain controlled conditions.

A. Chemicals with a flash point below 200 F (93.3 C) will be considered "firehazard chemicals"; B. OSHA standards and the National Fire Protection Association (NFPA) guidelines on when a chemical is considered flammable apply to the use of flammable chemicals in the laboratory. In all work with fire-hazard chemicals, follow the requirements of 29 CFR, sub-parts H and L; NFPA Manual 30, "Flammable and Combustible Liquids Code"; and NFPA Manual 45, "Fire Protection for Laboratories Using Chemicals"; C. Fire-hazard chemicals should be stored in a flammable-solvent storage area or in storage cabinets designed for flammable chemicals; D. Fire-hazard chemicals should be used only in vented hoods and away from sources of ignition. Procedures for Reactive Chemicals The most complete and reliable reference on chemical reactivity is found in the current edition of "Handbook of Reactive Chemical Hazards" by L. Bretherick, published by Butterworth-Heinemann, 1990. Reactivity information is sometimes given in manufacturer's MSDS's and on labels. Guidelines on which chemicals are reactive can be found in regulations published by the Department of Transportation (DOT) in 49 CFR and by the Environmental Protection Agency (EPA) in 40 CFR. Also see NFPA Manual 325M, "Fire Hazard Properties of Flammable Liquids, Gases, Volatile Solids"; Manual 49, "Hazardous Chemicals Data"; and Manual 491M, "Manual of Hazardous Chemical Reactions". A. A reactive chemical is one that meets any of the following: 1. Is described as such in Bretherick or the MSDS; 2. Is ranked by the NFPA as 3 or 4 for reactivity; 3. Is identified by the DOT as: An oxidizer; An organic peroxide; or An explosive, Class A, B, or C. 4. Fits the EPA definition of reactive in 40 CFR 261.23; 5. Fits the OSHA definition of unstable in 29 CFR 1910.1450; or 6. Is known or found to be reactive with other substances. B. Handle reactive chemicals with all proper safety precautions, including segregation in storage and prohibition on mixing even small quantities with

other chemicals without prior approval and appropriate personal protection and precautions. Procedures for Corrosive Chemicals and Contact-Hazard Chemicals Corrosivity, allergenic, and sensitizer information is sometimes given in manufacturer's MSDS's and on labels. Also, guidelines on which chemicals are corrosive can be found in other OSHA standards and in regulation published by DOT in 49 CFR and the EPA in 40 CFR. A. A corrosive chemical is one that meets any of the following: 1. Fits OSHA definition of corrosive in Appendix A of 29 CFR 1910.1200; 2. Fits the EPA definition of corrosive in 40 CFR 261.22 (has a ph greater than 12 or less than 2.5); or 3. Is known or found to be corrosive to living tissue. B. Handle corrosive chemicals with all proper safety precautions, including wearing both safety goggles and a face shield, gloves tested for absence of pin holes and known to be resistant to permeation or penetration, a laboratory coat and a rubberized apron. C. A contact-hazard chemical is an allergen or sensitizer when it meets any of the following: 1. Identified or described in the MSDS or on the label; 2. Identified or described in the medical or industrial hygiene literature; or 3. Is known or found to be an allergen or sensitizer. Procedures for Compressed Gases Compressed gas cylinders may have many hazards. They often contain materials which are toxic or highly flammable. If mishandled or if they fall over, they can become "unguided missiles" with enough explosive force to penetrate a concrete wall. If they tip over, they can fall on other equipment, stored chemicals, or on nearby personnel. Corrosive compressed gases constitute another hazard. If they are stored for a lengthy period of time after use, the corrosive nature of the material may affect the valves. Therefore, corrosive compressed gases should not be stored for more than six months.

Guidelines for transportation and storage of compressed gas cylinders: Leaks 1. Make sure the valve cap is securely in place before moving any cylinder. 2. Transport cylinders on a designated wheeled cart (designed for the specific task), carefully secured (by a chain) in an upright position to prevent them from falling. 3. Make sure the label is legible and secured to the cylinder (use packaging tape if necessary to prevent it from falling off). 4. Do not leave a cylinder unattended in a corridor for more than a few minutes. 5. Never move a cylinder by rolling it across the floor. 6. Never drop cylinders or bang them against each other or another object. 7. When a cylinder is not in use, make sure the valve cap is securely in place. 8. Whether in use or in storage, all cylinders must be double strapped or double chained in an upright position, according to Fire Marshal requirements. For assistance with the double strapping requirement, call Environmental Health and Safety at 657-278-7233 (x. 7233). 1. Report all suspected leaks immediately - if the material in the cylinder is highly toxic, evacuate everyone from the area - call Environmental Health and Safety Department at extension 657-278-7233, Public Safety at extension 2515, or in an extreme emergency call 911. 2. Leaking cylinders should be put in or near a fume hood, if possible. Disposal 1. Empty cylinders should be labeled "empty" and returned to the appropriate area or vendor for refill or disposal. 2. Empty lecture bottles may be returned to the manufacture or vendor call the Chemical Hygiene Officer at x. 5938 or Environmental Health & Safety Department at 657-278-7233 for assistance. 3. Any suspected "unknown" cylinders should be reported to Environmental Health and Safety Department at 657-278-7233. 4. Always leave at least 25 psi in all "empty" cylinders to prevent contamination and the formation of explosive materials.

V. Control Measures and Equipment Ventilation Many laboratory workers depend on fume hoods to protect themselves from the potentially dangerous fumes of the chemicals they must use. Fume hoods prevent or minimize the escape of contaminants from the hood into the laboratory. A fume hood may also minimize the potential for fire or explosion from vapors of flammable chemicals. Successful performance of the fume hood depends primarily on adequate and even velocity of air moving through the hood. This is adversely affected by cross drafts, thermal load and obstruction of the hood sash and rear intake baffles. As fume hoods are designed to operate most effectively with room doors closed, proper venting may not be guaranteed with the room doors open. To allow for adequate protection, the hood user must avoid work practices and procedures that interfere with hood performance. Hazardous operations involving toxic and explosive chemicals, pathogenic microorganisms, or radioisotopes in certain forms, must be performed within these enclosures. The exhaust systems are a prime safety feature for the laboratory and serve four major functions: A. Confining hazardous contaminants and preventing their coming into contact with persons working in the laboratory; B. Transporting these hazardous materials to a point where they may be discharged safely into the atmosphere; C. Sufficiently diluting toxic chemicals to prevent pollution of the atmosphere. Ventilation used for work with highly pathogenic microorganisms or certain radioactive particles should be fitted with filters to entrap these particles and prevent their discharge; D. Providing sufficient air movement within the enclosure so that flammable vapor concentrations will be reduced below their lower explosive limits. For adequate containment, the linear velocity of air moving into the hood at the face should be at least 100 feet per minute (fpm) at the working sash height. The hoods are surveyed annually and the face velocity and optimum working sash height will be labeled on each hood. Fume Hood Safety Procedures A. Use all toxic chemicals inside the hood, but do not use the hood as a storage cabinet; B. Operate hood at proper sash height, as marked on the hood; C. Work at least six inches in from the plane of the sash. Keep all chemicals and equipment behind this line during every experiment;