INTEGRATED CIRCUITS -Input NAND gate 1991 Feb 0 IC05 Data Handbook
TPE TPICAL PROPAGATION DELA TPICAL SUPPL CURRENT (TOTAL) 5.0ns 0.5mA PIN CONFIGURATION A 1 B 2 14 13 V CC NC ORDERING INFORMATION C 3 12 H ORDER CODE D 4 11 G DESCRIPTION COMMERCIAL RANGE V CC = 5V ±, T amb = 0 C to +70 C DRAWING NUMBER 14-pin plastic DIP N SOT27-1 E F GND 5 6 7 10 9 NC NC 14-pin plastic SO D SOT10-1 SC00029 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE NOTE: PINS DESCRIPTION 74ALS (U.L.) HIGH/LOW LOAD VALUE HIGH/LOW A H Data inputs 1.0/1.0 20µA/0.1mA Data output 20/0 0.4mA/mA One (1.0) ALS unit load is defined as: 20µA in the High state and 0.1mA in the Low state. LOGIC SMBOL IEC/IEEE SMBOL 1 & 1 2 3 4 5 6 11 12 2 3 A B C D E F G H 4 5 6 11 12 V CC = Pin 14 GND = Pin 7 SC00031 SF00073 LOGIC DIAGRAM FUNCTION TABLE V CC = Pin 14 GND = Pin 7 1 A 2 B C 3 D 4 5 E 6 F G 11 H 12 SC00030 INPUTS OUTPUT A B C D E F G H H H H H H H H H L L X X X X X X X H X L X X X X X X H X X L X X X X X H X X X L X X X X H X X X X L X X X H X X X X X L X X H X X X X X X L X H X X X X X X X L H H = High voltage level L = Low voltage level X = Don t care 1991 Feb 0 2 53 1099 01670
ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SMBOL PARAMETER RATING UNIT V CC Supply voltage 0.5 to +7.0 V V IN Input voltage 0.5 to +7.0 V I IN Input current 30 to +5 ma V OUT Voltage applied to output in High output state 0.5 to V CC V I OUT Current applied to output in Low output state 16 ma T amb Operating free-air temperature range 0 to +70 C T stg Storage temperature range 65 to +150 C RECOMMENDED OPERATING CONDITIONS SMBOL PARAMETER LIMITS MIN NOM MAX V CC Supply voltage 4.5 5.0 5.5 V V IH High level input voltage 2.0 V V IL Low level input voltage 0. V I Ik Input clamp current 1 ma I OH High level output current 0.4 ma I OL Low level output current ma T amb Operating free-air temperature range 0 +70 C UNIT DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SMBOL PARAMETER TEST CONDITIONS 1 MIN TP 2 MAX LIMITS UNIT V OH High-level output voltage V CC ±, V IL = MAX, V IH = MIN, I OH = 0.4mA V CC 2 V V = MIN, V = MAX, I OL = 4mA 0.25 0.40 V V OL Low-level output voltage CC IL V IH = MIN I OL = ma 0.35 0.50 V V IK Input clamp voltage V CC = MIN, I I = I IK -0.73-1.5 V I I Input current at maximum input voltage V CC = MAX, V I = 7.0V 0.1 ma I IH High level input current V CC = MAX, V I = 2.7V 20 µa I IL Low level input current V CC = MAX, V I = 0.5V -0.1 ma I O Output current 3 V CC = MAX, V O = 2.25V -30-112 ma I CC Supply current (total) I CCH V CC = MAX I CCL V I = 0V 0.20 0.36 ma V I = 4.5V 0.64 0.9 ma NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at V CC = 5V, T amb = 25 C. 3. The output conditions have been chosen to produce a current that closely approximate one half of the true short circuit output current, I OS. 1991 Feb 0 3
AC ELECTRICAL CHARACTERISTICS SMBOL PARAMETER TEST CONDITION LIMITS T amb = 0 C to +70 C V CC = +5.0V ± C L = 50pF, R L = 500Ω UNIT MIN MAX t PLH t PHL Propagation delay A, B, C, D, E, F, G, H to n Waveform 1 2.0 3.0.0 10.0 ns AC WAVEFORMS For all waveforms, = 1.3V. A, B, C, D, E, F, G, H t PHL t PLH SC00032 Waveform 1. Propagation Delay for Data to Output TEST CIRCUIT AND WAVEFORMS PULSE GENERATOR V IN V CC D.U.T. V OUT NEGATIVE PULSE t THL ( t ff) t w t TLH ( t r ) AMP (V) 0.3V R T C L R L Test Circuit for Totem-pole Outputs POSITIVE PULSE t TLH ( t r ) t w t THL ( t f ) AMP (V) 0.3V DEFINITIONS: R L = Load resistor; see AC electrical characteristics for value. C L = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. R T = Termination resistance should be equal to Z OUT of pulse generators. Family 74ALS Input Pulse Definition INPUT PULSE REQUIREMENTS Amplitude 3.5V 1.3V Rep.Rate t w t TLH t THL 1MHz 500ns 2.0ns 2.0ns SC00005 1991 Feb 0 4
DIP14: plastic dual in-line package; 14 leads (300 mil) SOT27-1 1991 Feb 0 5
SO14: plastic small outline package; 14 leads; body width 3.9 mm SOT10-1 1991 Feb 0 6
DEFINITIONS Data Sheet Identification Product Status Definition Objective Specification Preliminary Specification Product Specification Formative or in Design Preproduction Product Full Production This data sheet contains the design target or goal specifications for product development. Specifications may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes at any time without notice, in order to improve design and supply the best possible product. Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices, or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale. Philips Semiconductors 11 East Arques Avenue P.O. Box 3409 Sunnyvale, California 940 3409 Telephone 00-234-731 Copyright Philips Electronics North America Corporation 1997 All rights reserved. Printed in U.S.A. 1991 Feb 0 7