VALVES & ACCESSORIES 91

VAVES & ACCESSORIES 91

Table of Contents Figure 39101 & 39107 Grooved Butterfl Valves Flow Data Page 93 Figure 39101HV Butterfl Valves 10 Position Handle ever Operated for HVAC Applications Page 94 Figure 39101 Butterfl Valve, ever Operated for Potable Water Applications Page 95 Figure 39101N Butterfl Valves, ever Operated with Nitrile Disc Page 96 Figure 39107 Butterfl Valves Gear Operated for Potable Water Applications Page 97 Figure SJ-200 ow Profile Butterfl Valves Page 9 Model B101 ow Profile Butterfl Valves Page 99 Figure B333 arge Diameter Butterfl Valve Page 100-101 Model BV35 Ball Valves Pages 102-103 Model SJ-530 Ball Valve (3 Port) Pages 106 Model CV-1 Grooved End Check Valves Pages 107-10 Model SJ-915 Dual Disk Check Valves 65-300 (2 1 2-12") Page 109 Model SJ-915 Dual Disk Check Valves 350-600 (14" - 24") Page 110 Model CB00 Balancing Valves Overview Page 111 Model CB00 Threaded Balancing Valves Page 112 Model CB00 Grooved Balancing Valves Page 113 Model CB00 Flanged Balancing Valves ANSI & PN16/PN10 Page 114-115 Model CB00 Solder Balancing Valves Page 116 Model CB00 Circuit Balancing Insulation Kits Page 117 Model CB00 Circuit Balancing Valves MC2 Measuring Computer Page 117 Figure 760 WYE Strainer Page 120 Figure S55 Tee Strainer Page 121 Figure S10 Suction Diffusers Pages 122-123 Figure 7550 Expansion Joints Pages 124-129 Figure RXAG Expansion Joint Page 130 Figure AG Expansion Joint Page 131 Figure ANS Expansion Joint Page 132 Figure FTU Rubber Bellows ISO R7 Threaded Page 132 Figure FSF Flanged Rubber Bellows Page 133 Figure UFBX Flexible Hoses Pages 134-135 Figure HERCUES Fix Point Page 136 Model SJ-500 Ball Valve Pages 104 Figure 70607 Groove Ended Metering Station Page 11 Figure FAZ Anchor Page 137 Model SJ-500W Ball Valve Gear Operated Pages 105 Figure Venturi Flow Meter Butt Weld with Grooved Ends Page 119 Figures 407GT & 407T Dielectric Waterwas Page 13 * Shurjoint product specifications can be found at www.shurjoint.com General notes: Additional information is included in our data sheets and is available upon request. It is the Designer s responsibilit to select products suitable for the intended service and to ensure that pressure ratings and performance data is not exceeded. Alwas read and understand the installation constructions. Never remove an piping components nor correct or modif an piping deficiencies without first depressurizing and draining the sstem. Material and gasket selection should be verified with the gasket recoendation listing for the specific application. 92 GRINNE reserves the right to change the contents without notice. www.grinnell.com

Figures 39101 & 39107 Grooved Butterfl Valve Flow Characteristics The uniqueness of the grooved valve begins with the spherical bore of the disc seat area which facilitates a constant disc to seat loading that maintains a leak tight stem seal regardless of disc position. Because seal force is constant throughout the full disc ccle, operating torques are kept low thus increasing valve life. The grooved butterfl valve is the grooved end valve with the lowest pressure loss. This is accomplished b combining the best features of ball valve and butterfl designs. Utilizing the spherical bore of a ball valve design enables the use of a thin profile disc with much narrower leading edges which, while providing a bubble tight seal affords the advantage of minimal flow turbulence through the valve. This reduces pressure loss and allows more precise flow control over a wider range of flow conditions and disc positions. Also designed with the contractor in mind, the valve bod is a rugged one-piece casting with integral mounting base for either manual operated or remote controlled actuation while providing room for vital pipe sstem insulation. DN Size UOM Flow Characteristics Kv values in /min (UK-GMP & US-GPM) For Figures 39101 and 39107 Butterfl Valves 20 C (6 F) 30 C (6 F) 40 C (104 F) 50 C (122 F) 60 C (140 F) 70 C (15 F) 0 C (176 F) 90 C (194 F) 50 60.3 /min 57 135 315 62 1100 1643 1767 150 65 73.0 /min 2 200 457 5 1600 2300 2600 2717 65 76.1 /min 2 200 457 5 1600 2300 2600 2717 0.9 /min 12 315 657 1315 2400 3500 4050 4150 100 114.3 /min 215 500 105 2150 3767 623 133 567 125 139.7 /min 415 915 150 3417 6033 9433 12750 13717 125 141.3 /min 415 915 150 3417 6033 9433 12750 13717 150 165.1 /min 62 1400 3067 6150 10567 16067 19933 21433 150 16.3 /min 62 1400 3067 6150 10567 16067 19933 21433 200 219.1 /min 1172 2750 5650 1123 20500 33367 47500 52150 250 273.0 /min 2000 5717 12217 20717 36650 56067 77350 1433 300 323.9 /min 3067 717 1567 31717 55933 93217 11000 12423 The relation between Cv and Kv is different for UK and US: (UK) Cv = 0.97Kv and (US) Cv = 1.17Kv, The imperial (UK) gallon is officiall defined as 4.546 liters. The imperial (US) gallon is officiall defined as 3.75 liters. Refer to back cover for countr-specific contact information 93

Figure 39101HV Butterfl Valve, 10 Position Handle ever Operated for HVAC Applications MATERIA SPECIFICATIONS Bod Disc Control Shaft & Spindle Retainer Plug O-Ring ocking Ring Performance Part Number Pipe Size Max. Wk Pressure Bar psi Dimensions - A B C D E F ever Tpe Approx 39101HV060 39101HV073 39101HV076 39101HV09 39101HV114 39101HV139 39101HV141 39101HV165 39101HV16 39101HV219 50 60.3 16 100 77.5 1 230 69 45 1.9 C 4 65 73.0 16 105 2 97 230 69 45 2.9 C 4 65 76.1 16 105 2 97 230 69 45 2.9 C 4 0.9 16 112 90 97 230 69 45 3.4 C 4 100 114.3 16 135 107 116 320 77 50 125 139.7 16 147 121 14 320 77 50 125 141.3 16 147 121 14 320 77 50 150 165.1 16 10 150 14 420 77 50 12.1 C 20 150 16.3 16 10 150 14 420 77 50 12.1 C 20 200 219.1 16 204 172 133 420 77 50 14.7 C 20 Note: maximum working temperature 110 C (230 F) Recoended for mounting with GRINNE Rigid Couplings. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 94 GRINNE reserves the right to change the contents without notice. www.grinnell.com C 12 C 12 C 12 5.3.5.5

Figure 39101 Butterfl Valve, ever Operated for Potable Water Applications MATERIA SPECIFICATIONS Bod Disc Control Shaft & Spindle Bushing Retainer Plug O-Ring ocking Ring Performance Part Number Pipe Size Max. Wk Pressure Bar psi Dimensions - A B C D E F ever Tpe Approx 39101-060 39101-073 39101-076 39101-09 39101-114 39101-139 39101-141 39101-165 39101-16 39101-219 50 60.3 16 100 77.5 1 230 70 45 1.9 C 4 65 73.0 16 105 2 97 230 70 45 2.9 C 4 65 76.1 16 105 2 97 230 70 45 2.9 C 4 0.9 16 112 90 97 230 70 45 3.4 C 4 100 114.3 16 135 107 116 320 76 50 125 139.7 16 147 121 14 320 76 50 125 141.3 16 147 121 14 320 76 50 150 165.1 16 10 150 14 420 76 50 12.1 C 20 150 16.3 16 10 150 14 420 76 50 12.1 C 20 200 219.1 16 204 172 133 420 76 50 14.7 C 20 Note: recoended for mounting with GRINNE Rigid couplings Working temperature range is -15 C to 0 C (5 F to 176 F) Option: silicon free valves for automotive industr. Because of the special grease, the agenc approvals do not appl. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Refer to back cover for countr-specific contact information 95 C 12 C 12 C 12 5.3.5.5

Figure 39101N Butterfl Valves, ever Operated with Nitrile Disc MATERIA SPECIFICATIONS Bod Disc Control Shaft & Spindle Bushing Retainer Plug O-Ring ocking Ring Performance Part Number Pipe Size Max. Wk Pressure Bar psi Dimensions - A B C D E F ever Tpe Approx 39101N-060 39101N-073 39101N-076 39101N-09 39101N-114 39101N-139 39101N-141 39101N-165 39101N-16 39101N-219 50 60.3 16 100 77.5 1 230 70 45 1.9 C 4 65 73.0 16 105 2 97 230 70 45 2.9 C 4 65 76.1 16 105 2 97 230 70 45 2.9 C 4 0.9 16 112 90 97 230 70 45 3.4 C 4 100 114.3 16 135 107 116 320 76 50 125 139.7 16 147 121 14 320 76 50 125 141.3 16 147 121 14 320 76 50 150 165.1 16 10 150 14 420 76 50 12.1 C 20 150 16.3 16 10 150 14 420 76 50 12.1 C 20 200 219.1 16 204 172 133 420 76 50 14.7 C 20 Note: recoended for mounting with GRINNE Rigid couplings Working temperature range is -15 C to 0 C (5 F to 176 F) For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 96 GRINNE reserves the right to change the contents without notice. www.grinnell.com C 12 C 12 C 12 5.3.5.5

, * 0 Figure 39107 Butterfl Valves, Gear Operated for Potable Water Applications MATERIA SPECIFICATIONS Bod Disc Control Shaft & Spindle Bushing Retainer Plug O-Ring ocking Ring * + Performance 1 -. / Part Number 39107-09 39107-114 39107-139 39107-141 39107-165 39107-16 39107-219 39107-273 39107-324 Pipe Size Max. Work Pressure Bar psi Dimensions - A B C E G K M N P øv 0.9 16.0 112 90 97 137 72 53 15 55 45 172 150 7.4! " " # " $! %! $! % &! $! # & # & & ' & & % # # ' Approx 100 114.3 16.0 135 107 116 170 101 79 22 77 67 216 300 15.0 " "! # "! # " & ' ' % % $ # # $ % $! ' " $ # # $ # # 125 139.7 16.0 147 121 14 12 101 79 22 77 67 22 300 1.3 # % ( & ) )! & % " & ' $ & # & % $ # # $ % $! ' " $ % $ # # $ # " 125 141.3 16.0 147 121 14 12 101 79 22 77 67 22 300 1.5 '! & % " & ' $ & # & % $ # # $ % $! ' " $ % $ # # $ # " $ 150 165.1 16.0 10 150 14 215 101 79 22 77 67 261 300 21.4 # ' ( # ) ) '! & % % # $ $ " ' % $ # # $ % $! ' " #! $ # # $ # " &! 150 16.3 16.0 10 150 14 215 101 79 22 77 67 261 300 21.7 ' ' '!! & % % # $ $ " ' % $ # # $ % $! ' " #! $ # # $ # " & $ 200 219.1 16.0 204 172 133 239 101 79 22 77 67 25 300 24.0 $ $ '!! $ ' & &! " % " # % $ # # $ % $! ' " # #!! # # $ #! % 250 273.0 12.7 250 233 159 2 11 2 22 79 0 332 300 40.0 # # & # & % $ " % # & '! ' # # " " '! $ % $ # # # # & # # $ # $ $! 300 323.9 12.7 275 25 165 313 11 2 22 79 0 357 300 49.0 #! #! & # & # $ # # ' ' #!! " '! $ % $ # # # # " ' # # $ # # $ Note: recoended for mounting with GRINNE Rigid couplings Working temperature range is -15 C to 0 C (5 F to 176 F) For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Refer to back cover for countr-specific contact information 97

2 Shurjoint Figure SJ-200 ow Profile Butterfl Valve Shurjoint Tech Data Sheet: J-35 3 4 4 Pressure-Temperature Rating Nom. Rating Working Pressure Shell Test Max. Service Temperature CWP Not Recoended for Steam. 16 Bar @3 C 5 6 7 9 : 24 Bar 5 6 7 EPDM: 110 C ; < = >? 9 : Nitrile: 2 C @ 7 A B 7 C D? 9 : *Working pressure is based on connection with roll- or cut-grooved standard wall carbon steel pipe. *Seat test: 110% the working pressure. The Shurjoint Model SJ-200 Butterfl Valve is a low profile, grooved-end butterfl valve designed for oil & gas, mining and other service applications. The working pressure is rated up to 16 Bar (232 psi) and service temperatures are rated to 2 C (10 F) (Nitrile bod liner). The Model SJ-200 features a full rubber lined bod with 316 stainless steel disc. This makes the SJ-200 great for mining, oil and gas applications due to its superior abrasive and corrosion resistance. The end to end dimensions conform to MSS SP-67. The lever handle is equipped with a tamper resistant locking device. MATERIA SPECIFICATIONS Valve Bod: ASTM A 395, Gr. 65-15-45, min tensile strength 441 Bar (65,000 psi). Disc: Valve Bod Coating: Valve Bod iner: (colour code: Orange stripe) Recoended for petroleum products, vegetable oils, mineral oils and air with oil vapors. Temperature range: -29 C to 2 C (-20 F to 10 F ). Do not use for HOT WATER above 66 C (150 F ) or HOT DRY AIR above 60 C (140 F ). Upper & ower Shafts: O-Ring: Nut: ever Handle: Performance Representative. Pipe Size Dimensions - Approx. A B C H 50 60.3 1.0 4 57 140 0.9 65 73.0 97.0 54 67 190 1.5 0.9 97.0 62 75 190 1.9 100 114.3 116.0 76 106 274 3.9 150 16.3 14.0 104 139 274 10.1 200 219.1 133.0 140 152 274 11.3 Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 9 GRINNE reserves the right to change the contents without notice. www.grinnell.com

Model B101 ow Profile Butterfl Valves Tech Data Sheet: G330 The GRINNE Model B101 ow Profile Butterfl Valve has a rated working pressure of 13. Bar (200 psi) and provides efficient control of fluid in piping sstems. Flow can be from either direction and the valve ma be positioned in an orientation. The ductile iron bod is epox-coated to resist atmospheric corrosion. The disc is EPDM encapsulated ductile iron compatible with a variet of chemicals and temperature ranges. MATERIA SPECIFICATIONS Bod Bod Coating Disc Disc Seal encapsulated rubber -29 C to 121 C (-20 F to 250 F ) with intermittent service at 121 C (250 F ) and continuous service at 107 C (225 F ) encapsulated rubber -29 C to 2 C (-20 F to 10 F ) Stem Stem Seal Handle Performance Representative. A B E C F D Pipe Size Dimensions - Approx. A B C D E F 50 60.3 6.0 152.0 25.0 46.0 50.0 0.0 1.9 65 73.0 96.0 152.0 25.0 52.0 61.0 91.0 2.9 0.9 96.0 210.0 25.0 65.0 67.0 107.0 3.4 100 114.3 115.0 210.0 25.0 3.0 3.0 123.0 5.3 125 141.3 139.7 311.2 32.0 101.6 101.6 171.5 5. 150 16.3 132.0 305.0 32.0 109.0 109.0 174.0 12.1 For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Refer to back cover for countr-specific contact information 99

Figure B333 arge Diameter Butterfl Valve (Page 1 of 2) Tech Data Sheet: G235 The GRINNE Model B333 arge Diameter Butterfl Valve provides efficient control of fluid flow in piping sstems. It is a grooved-end bubble tight shut-off valve with endto-end dimensions that meet MSS SP-67, Table 4 and a mounting pad that meets ISO 5211 for the mounting of power actuators. The valve is capable of bidirectional fluid flow at working pressures to 20 bar (300 psi) and ma be positioned in an orientation. The 350 to 600 (14" to 24") Model B333 Butterfl Valve is configured with a worm tpe gear operator and consists of an epox powder coated ductile iron bod and EPDM or Nitrile (NBR) rubber encapsulation dual-seal disc. The bod and disc construction provides for increased strength and durabilit. The disc seal and bod coating are compatible with a variet of chemicals and temperature ranges. Contact our GRINNE Representative for specific recoendations on seal and coating selections. MATERIA SPECIFICATIONS Valve Bod & Disc 12 and/or to ASTM A395 Gr. 65-45-15 Stem Seals Bod Coating Disc Encapsulation Upper and ower Shafts Gear Operator Housing Set Screw Spring Pin Maximum Working Pressure (300 psi), non-shock cold water Seat Material For service temperatures from -34 C to 93 C ( -30 F to 200 F). Recoended for water service, dilute acids, alkalies, oil-free air, and man chemical services. THEY ARE NOT RECOMMENDED FOR USE IN PETROEUM SERVICES. For service temperatures from -29 C to 2 C ( -20 F to 10 F). Recoended for petroleum products, air with oil vapors, vegetable oils, and mineral oils. THEY ARE NOT RECOMMENDED FOR USE IN HOT WATER SERVICES. Contact a GRINNE Sales Representative for specific recoendations on seat material. Performance Representative. 100 GRINNE reserves the right to change the contents without notice. www.grinnell.com

E 1 Figure B333 arge Diameter Butterfl Valve (Page 2 of 2) Tech Data Sheet: G235 3 4 4 Pipe Size Dimensions - Approx. A B C D E F 350 355.6 17 365 224 276 242 305 59 400 406.4 17 416 24 302 242 305 67 450 457.2 203 470 23 350 242 305 6 500 50.0 216 527 314 33 290 412 133 600 609.6 254 629 36 463 290 412 160 For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Worm Gear Operator - PCD Dia. Bolt Size K Dimensions S Approx. 350 125 24.0 14.9 M12 400 140 450 140 M16 M16 36.6 14.9 41.3 14.9 500 165 52.0 30.5 M20 600 165 52.0 30.5 M20 For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Refer to back cover for countr-specific contact information 101

Model BV35 Ball Valves (Page 1 of 2) Tech Data Sheet: G30 GRINNE Model BV35 Ball Valves provide for efficient control of fluid in piping sstems. Flow ma be from either direction, and the valves ma be positioned in an orientation. The valves are furnished with grooved ends for use with GRINNE Grooved Couplings. The handle is provided with a device for padlocking in either the open or closed position. The GRINNE Model BV35 is furnished with grooved ends and features a handle that accepts a padlock device for locking in either the open or closed position. Flow ma be from either direction and the valves ma be positioned in an orientation. Maximum Working Pressure 6,9 Bar (1,000 psi) 50 0 (1 1 2" 3") 55,2 Bar (00 psi) 100-150 (4" - 6") Shell Test 1.5 times WOG x 60 seconds, hdrostatic, at ambient temperature Seat Test 5,5 Bar (0 psi) x 60 seconds, pneumatic MATERIA SPECIFICATIONS Bod ASTM A 536, Grade 65-45-12 Bod Coating Ball Bod Seal Seats O-Ring Stem - Tpe 304 Stainless Steel available ever Handle - Tpe 304 Stainless Steel available Gear Operator Pipe Size Dimensions - A B C D 102 GRINNE reserves the right to change the contents without notice. www.grinnell.com Cv Value Approx. 40 4.3 130 6 17 32 2.2 130 50 60.3 140 95 17 3 2.9 10 65 73.0 159 132 265 50 0.9 167 143 265 63 100 114.3 240 94 265 90 25.0 1020 150 16.3 25 221 600 125 36.0 3300 * For the first opening or closing of the valve when the valve is not continuousl operated, an additional torque of 2.0 2.5 times the listed operating torque is normall required. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 320 600 4. 6.1

Model BV35 Ball Valves (Page 2 of 2) Tech Data Sheet: G30 Pressure Performance 10,000 A C Pressure (kpa),000 6,000 4,000 B E 2,000 0 0 50 100 200 250 Temperature (C ) Flow Data - Cv Values Values for flow of water at 16 C (60 F) C v = Q D Where: Cv = Flow coefficient Q = Flow (GPM) P = Pressure drop (psi) Pipe Size Dimensions - A B C D E 40 4.3 130 124 203 32 152 50 60.3 140 137 203 3 152 Refer to back cover for countr-specific contact information 103 Cv Value 130 10 Approx. 65 73.0 159 145 203 50 152 10.0 320 0.9 167 12 203 63 152 14.0 600 100 114.3 240 203 203 90 152 33.0 1020 150 16.3 25 277 356 125 305 For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. range of the gasket used in the coupling. For additional information, contact a GRINNE Sales Representative. Schedule 40 steel pipe with roll grooves to ANSI/AWWA C606-04 specifications. For information on other pipe schedules, contact a GRINNE Sales Representative. an components. 3300 7.0.0 56.0

, G J 2, J I 2 Shurjoint Model SJ-500 Ball Valve (Page 1 of 2) Shurjoint Tech Data Sheet: J-06 The Shurjoint Model SJ-500 is a ductile iron, grooved-end, two-piece, regular port ball valve designed and tested in conformance with MSS SP-110 and SP-72. The lever handle is equipped with tamper resistant locking holes. The SJ-500 is comprised of a ductile iron bod and end cap, virgin TFE seats and chrome-plated carbon steel trim. Also available with stainless steel trim as an option. I 3 4 4 3 4 4 M M N O P Q K Pressure-Temperature Rating Nom. Rating CWP Size Working Pressure 40-0 70 Bar @ 3 C 5 6 7 9 : 100-150 56 Bar @ 3 C 5 6 7 9 : Max. Service Temperature EPDM: @ 110 C (230 F) 7 A B 7 C D? 9 F 9 : H *Working pressure is based on connection with roll- or cut-grooved standard wall carbon steel pipe. *Seat test: 110% the working pressure. Pipe Size Pipe Working Pressure Bar psi Operating N / m b/in Dimensions - H W d A B C Approx. 40 4.3 70 7 130 6 17 32 15.9 7.9 45.1 1. 50 60.3 70 17 140 95 17 3 15.9 7.9 57.2 2.9 65 73.0 70 21 159 132 265 50 15.9 7.9 69.1 4.4 65 76.1 70 21 159 132 265 50 15.9 7.9 72.3 4.4 0.9 70 2 167 143 265 63 15.9 7.9 4.9 7. 100 114.3 56 45 240 94 265 90 15.9 7.9 110.0 14.7 150 165.1 56 60 25 221 600 125 15.9 9.5 163.9 41.1 150 16.3 56 60 25 221 600 125 15.9 9.5 163.9 41.1 * When first opening or closing the valve when not continuosl operated. Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 104 GRINNE reserves the right to change the contents without notice. www.grinnell.com

1 J 2 1 J 2 The Shurjoint Model SJ-500W can be equipped with a worm gear operator. The standard gear operator is supplied with a bracket and extension sleeve. The ISO 5211 mounting pad allows for the mounting of power actuators. Shurjoint Model SJ-500W Ball Valve Gear Operated (Page 2 of 2) Shurjoint Tech Data Sheet: J-06 MATERIA SPECIFICATIONS Bod and End Cap: ASTM A 395, Gr. 65-45-15. Stem & Ball: Seats: Bod Seal: O-Ring: ever Handle: Gear Operator: Performance Representative. 40 to 100 (1 1 2" - 4") 150 (6") Pipe Size Dimensions Approx. Pipe K H W 40 4.3 152 124 203 7.0 50 60.3 152 137 203.0 65 73.0 152 145 203 10.0 65 76.1 152 145 203 10.0 0.9 152 12 203 14.0 100 114.3 152 203 203 33.0 150 165.1 305 277 356 56.0 150 16.3 305 277 356 56.0 Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Refer to back cover for countr-specific contact information 105

, J 2 Shurjoint Model SJ-530 Ball Valve (3 Port) Shurjoint Tech Data Sheet: J-40 The Shurjoint Model SJ-530 is a grooved-end three-port ball valve designed to divert media from bottom inlet to either of the two outlets ports. The valve port is a regular port size and the stem is a blowout proof design to MSS-SP-72 and API Standard 60. The valve is supplied with a carbon steel lever handle equipped with a tamper resistant locking device. The valve bod is made of ferritic ductile iron conforming to ASTM A 395/A (UNS F33100) with black electro deposition coating. The three-port ball is austenitic stainless steel to ASTM A 351 CFM (316) and blowout proof stem is stainless steel to ASTM A 479 Tpe 316. All materials are chosen to meet the requirements of NACE MR0175-2003. MATERIA SPECIFICATIONS Bod and End Cap: 3 4 4 I Surface Finish: Ball: Stem: Seats: Bod Seal: Pressure-Temperature Rating Nom. Rating CWP Working Pressure 41 Bar 5 6 7 @3 C 9 : Max. Service Temperature EPDM: 110 C ; < = >? 9 : Nitrile: 2 C @ 7 A B 7 C D? 9 : *Working pressure is based on connection with roll- or cut-grooved standard wall carbon steel pipe. *Seat test: 110% the working pressure. Stem Hardware: ever Handle: Performance Representative. Pipe Size Dimensions Approx. Pipe H W d A B 50 60.3 167 110 22 3 3 79 3.5 Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 106 GRINNE reserves the right to change the contents without notice. www.grinnell.com

a a The GRINNE Model CV-1 Grooved End Swing Check Valves are compact and rugged swing-tpe units that allow water flow in one direction and prevent flow in the opposite direction. The are manufactured with a ductile iron bod and a nickel-plated seat. 2" to ") have a stainless steel clapper assembl. 10" to 12") have a ductile iron clapper assembl. A resilient elastomer seal facing on the spring-loaded clapper ensures a leaktight seal and a non-sticking operation. The Model CV-1 Check Valves are designed to minimize water haer caused b flow reversal. The Model CV-1 Check Valve is furnished with grooved ends and can be installed using GRINNE Grooved Couplings or Flanged Adapters. The Model CV-1 Check Valves have been designed with a removable cover for ease of field maintenance. These valves can be installed horizontall (with cover in the upward position) or verticall with the flow in the upward direction. b ` c d e ` f g _ d g h i _ d g \ [ T X U ] Y Z S T U [ W X Y X U S W ^ _ ` h i _ d g Model CV-1 Grooved End Check Valves (Page 1 of 2) b ` c d e ^ _ ` R S T U V S W X Y Z S T U [ W X Y X U S W ` f g _ d g SPECIFICATIONS Valve Assembl Finish Max Working Pressure Clapper 2" - ") - Stainless Steel, 250 (10") - Ductile iro Tech Data Sheet: G352 Item No. Valve Material Specifications Description Material Qt. 1 Bod Ductile Iron 1 2 Cap Ductile Iron 1 3 Gasket Snthetic Fibre 1 4 Hex Cap Screw Steel, Zinc Plated AR 5 Clapper Stainless Steel or Ductile Iron 1 6 Seal Facing EPDM Grade E 1 7 Spring Stainless Steel 1 Hinge Shaft Stainless Steel 1 9 Retaining Ring Stainless Steel AR 10 Washer Teflon 2 11 Retention Bolt Stainless Steel 1 12 Seal Ring Neoprene 1 13 Retaining Disc Stainless Steel 1 14 ocknut Stainless Steel 1 15 Plug- 1 2"-14 NPT Cast Iron 2 16 Adhesive Thread Sealer AR 17 Nameplate Aluminium 1 1 Rivet Steel 2 19 Spacer Stainless Steel 1 9 2 DN65-DN200 (2-1/2" - ") 11 5 12 4,16 1 2 3 7 5 DN65-DN200 (2-1/2" - ") SEE VIEW A 1 17 9 2 DN250 (10") 7 5 VIEW A 13 13 11,16 14,16 19 6 5 DN250 6 (10") DETAI B 15 SEE DETAI B Refer to back cover for countr-specific contact information 107

b m n ^ d r n u Model CV-1 Grooved End Check Valves (Page 2 of 2) Tech Data Sheet: G352 j k ` l m l o p i q g o p i q g Part Number 595900020 595900025 595900076 595900030 595900040 595900139 595900050 595900165 595900060 59590000 595900100 595900120 DN s t u Pipe Size s t u A s t u B s t u C s t u Dimensions s t u D s t u E s t u F s t u J s t u Approx. kg v w x 50 60.3 171.5 111.3 64. 65.3 2.3 120.7 41.5 4.1 u z { } u { ~ u z u u { z u ~ u { u } u 65 73.0 203.2 147.3 6.6 6.4 9.6 152.4 43.2 4.5 u { u u z u ~ z u ~ z u } u { u u { } u z u u u z u ~ z u ~ z u } u u { u 65 76.1 203.2 147.3 6.6 6.4 9.6 152.4 43.2 4.5 z z u u z { u { } z u } z u ~ z u } u u { u 0.9 212.6 146.3 91.4 6.4 9.6 152.4 43.2 5.0 ~ ~ u u } z } u { ~ ~ u } z u } z ~ u } { u z u ~ u 100 114.3 245.6 171.2 117.1 92.2 115.1 11.1 46.7 11.3 125 139.7 266.7 190.5 134.4 106.7 124.5 193.0 4.3 13.2 z u { u u { u u ~ u ~ u { u } u u 125 141.3 266.7 190.5 134.4 106.7 124.5 193.0 4.3 13.2 u } z u { u u ~ u ~ u { u } u u } u } u u u u { ~ u u { u } u ~ ~ { u 150 165.1 292.1 204.4 146.1 114.3 127.0 193.0 37.6 21.3 150 16.3 292.1 204.4 146.1 114.3 127.0 193.0 37.6 21.3 } } u } u u u { ~ u u { u } u ~ ~ { u 200 219.1 355.6 260.4 196.9 142.7 13.4 213.4 5.9 29.9 u } ~ u u { u { u } u ~ u ~ } } u 250 273.0 457.2 330.2 259.3 162.1 190.5 266.7 76.2 49.4 u { u z u u } u z { u u z u u { 300 323.9 533.4 362.7 27.2 14.4 193.5 269.7 69.9 6.0 u { u ~ u u z { u } { u } u } u { u } For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Model CV-1 Pressure oss Data 10 GRINNE reserves the right to change the contents without notice. www.grinnell.com

k b j u The Shurjoint Model SJ-915 is a grooved-end dual-plate (or doubledoor) check valve designed to provide positive and silent protection against backflow in piping sstems. The valve features a ductile iron bod with an EPDM or Nitrile resilient seat molded to bod and tpe 304 stainless steel discs loaded with tpe 313 stainless steel springs. Groove dimensions compl with ANSI/AWWA C606. Features: valves) economical than wafer or lugged valves disc valves MATERIA SPECIFICATIONS Valve bod: ASTM A 395, Gr. 65-45-15. Seat (Rubber Gasket) & Stabilization Rubber: Discs: Torsion Springs: Disc hinge pin & disc stop pin: Spacer & Washer: Stop pin retainer: Performance Shurjoint Model SJ-915 Dual Disc Check Valves (Page 1 of 2) Pressure-Temperature Rating Nom. Rating Class 150 Working Pressure Shurjoint Tech Data Sheet: J-29 Size: 65-300 (2 1 2" - 12") 20 Bar x ˆ @3 C z Š Shell Test 30 Bar x ˆ ~ Max. Service Temperature EPDM: 110 C Œ Ž z Š Nitrile: 2 C ˆ ˆ Š *Working pressure is based on connection with roll- or cutgrooved standard wall carbon steel pipe. *Seat test: 110% the working pressure. Pipe Size Dimensions Approx. Pipe A B C 65 73.0 125 110 73 2.3 u { ~ u ~ u z z u { u 0.9 135 125 9 2.5 z z u u z ~ u z u u 100 114.3 137 152 114 3. ~ ~ u u z u ~ u u ~ 150 16.3 152 204 16 7.6 } } u } } u u z } u } u { 200 219.1 171 256 219 12.4 u } } u { z u u } { u z u { { u u u { ~ u 250 273.0 19 307 273 20.7 300 323.9 20 362 324 2.3 u { u ~ u u { } Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Refer to back cover for countr-specific contact information 109

~ b d k j u u Shurjoint Model SJ-915 Dual Disc Check Valves (Page 2 of 2) Shurjoint Tech Data Sheet: J-26 Size: 300-600 (14" - 24") Pressure-Temperature Rating Nom. Rating Class 150 Working Pressure 17 Bar x ˆ @3 C Š Shell Test 26 Bar x ˆ ~ m ` l m l Max. Service Temperature EPDM: 110 C Œ Ž z Š Nitrile: 2 C ˆ ˆ Š *Working pressure is based on connection with roll- or cutgrooved standard wall carbon steel pipe. *Seat test: 110% the working pressure. The Shurjoint model SJ-915 is a grooved-end dual disc check valve for pipelines conveing water and other fluids with the rated working pressure to 17 Bar (250 psi), available in sizes 350 to 600 (14 to 24 ). The valve features a full lined rubber bod, spring-loaded 304 stainless steel disc and shafts. The valve can be installed in a horizontal or vertical position (upward flow onl). Face to face dimensions conform to API 594 Class 150 and grooved ends to ANSI/AWWA C606. Seat test: (Hdrostatic) 1.90 MPa (275 psi) Shell test: (Hdrostatic) 2.75 MPa (400 psi) Features check valves) economical than wafer or lugged valves single disc valves maintenance MATERIA SPECIFICATIONS Bod: Gr. 65-45-12 and or ASTM A395, Gr. 65-45-15, minimum tensile strength 441 Bar (65,000 psi). Bod ining: Buna-N: Good for petroleum oils, mineral oils, vegetable oils, aromatic hdrocarbons, man acids and water 65 C (150 F) Maximum temperature range: -29 C to 2 C ( -20 F to 10 F). EPDM: Good for cold and hot water service up to 110 C (230 F). Not recoended for petroleum oils, mineral oils, solvents and aromatic hdrocarbons. Maximum temperature range: -34 C to 110 C ( -29 F to 230 F)*. * See Data Sheet J-26 Discs, Disc Shafts, & Spring: Washer: Performance Representative. Pipe Size Dimensions Approx. Pipe A B C D E 350 355.6 36 329 14 23 154 46.0 ~ ~ u ~ u ~ } { u ~ } u } u 400 406.4 410 359 191 310 173 54.0 } } u } u ~ ~ u z { } u u 450 457.2 461 417 203 364 203 77.0 u u } u ~ ~ u z z u } u ~ 500 50.0 509 460 219 40 226 96.0 u u ~ u } u } u u 600 609.6 610 562 222 457 249 131.0 ~ u ~ u u z u u u Refer to the Shurjoint technical data sheet for complete technical information and installation instructions. More information about Shurjoint Piping Products can be found on page 14 in the General Data section of this book or on www.shurjoint.com. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 110 GRINNE reserves the right to change the contents without notice. www.grinnell.com

} z z ~ GRINNE Model CB00 Circuit Balancing Valves are designed to achieve accurate and efficient balancing of hdronic heating or cooling sstems. Circuit Balancing Valves provide superior accurac in measuring flows rather than ball tpe circuit setters. The CB00 valve serves 5 functions: These valves are rated at 20.7 Bar (300 psi) at 150 C (300 F). The Y-Pattern stle provides low pressure drop. The globe stle valve allows for precise throttling. The eas-to-adjust digital/vernier handwheel provides a minimum of 70 unique handwheel positions. The handwheel and test ports are located on one side for eas access. A built-in memor stop ensures the setting can be returned to a balanced position after shutoff. The self-sealing pressure/temperature test ports use standard insertion probes to eliminate additional components. The GRINNE Circuit Balancing Valve is installed with flow in the direction of the arrow, and ma be in the horizontal or vertical position. The handwheel can be positioned up or down, or on either side. Size Flow Rate GPM PM 15 0.67-1.110 u } ~ u 20 0.9-1.63 z u ~ } u 25 1.63-2.536 } u u } 32 2.43-5.54 u ~ u 40 3.96-7.93 z 50 5.12-11.096 65 10.30-2.01 } 65 10.30-2.01 { } š z } 0 15.5-34.7 z } z 100 26.42-57.33 ~ { 125 29.59-3.75 z š { z { 125 29.59-3.75 z { 150 5.12-115.46 } š ~ z { 150 5.12-115.46 ~ z { 200 5.92-232.76 250 77.15-342.93 300 162.75-457.33 } } { z Connection Tpe Thread or Solder Flanged or Grooved CB00 Circuit Balancing Valves MATERIA SPECIFICATIONS Bod Tech Data Sheet: G450 ( 1 2" 2") solder or BSP threaded connection: brass-resistant to dezincification (DZR) (2 1 2" 12"), grooved or flanged connection: Cast Iron conforming to ASME ANSI B 16.5 Valve Stem and Disc O-Ring Handwheel For accessories and replacement parts contact a GRINNE Sales Representative for details. Valve Sizing All balancing valves are sized to perform in a normal operation range between 25% and 100% of the full open position, at a minimum differential pressure between 0.3 0.9m (1 3 ft.) of water. It is recoended that for improved accurac, the valve is set to open 70%+. When maximum flow is known but a pressure drop through the balancing valve is unknown, select a balancing valve for a maximum pressure drop of 0.6m (2 ft.) water 0.06 Bar (0. psi) in the full open position as shown in the table to the right. Accurate flow measurement requires that the velocit distribution near the balancing valve remains constant, regardless of the total flow through the pipe. Fittings, such as elbows and tees, disturb the normal flow profile which is established through straight pipe. Pumps create even greater disturbances. Failure to allow water flows around fittings and pumps to normalize can affect measuring accurac b as much as 20% when the valve is in the full open position. Minimum lengths (diameters, D) of straight pipe before and after the balancing valve prevent these errors. Valves are designed for vertical, horizontal, or inclined installation. Minimum Pipe Diameters from Fittings 3D 2D Pump 10D 2D Refer to back cover for countr-specific contact information 111

u Model CB00 Circuit Balancing Valves BSP Threaded Ends Tech Data Sheet: G450 The GRINNE Model CB00 Balancing Valve provides features for achieving accurate and efficient balancing of hdronic heating or cooling sstems. One valve serves five functions: throttling, measuring (pressure and temperature), positive shutoff, draining and filling. The GRINNE Thread-b-Thread Model CB00 Valve, available in sizes 15 to 50 ( 1 2" to 2"), is composed of zinc retaining brass. H Part Number CB000505 CB000755 CB001005 CB001255 CB001505 CB002005 Pipe Size Dimensions H Approx. imits PN/ C PSI/ F 15 21.3 79.5 104.9 0.6 16/150 u ~ z u z ~ u z u ~ z z u z u z ~ u } u ~ z z 20 26.9 4.1 115. 0.6 16/150 u z z u z ~ u } z z 25 33.7 5.6 119.1 1.0 16/150 32 42.4 111.3 136.7 1.4 16/150 u } } ~ u z u z z u z z 40 4.3 120.7 13.2 1.7 16/150 u ~ u { u ~ ~ z u z z 50 60.3 150.9 147.6 2.6 16/150 u z { u ~ u u } z z Handwheel Turns See circuit balancing valve specifications on pages 111. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 7 7 7 10 10 10 112 GRINNE reserves the right to change the contents without notice. www.grinnell.com

u u Model CB00 Circuit Balancing Valves Grooved Ends Tech Data Sheet: G450 The GRINNE Model CB00 Balancing Valve provides features for achieving accurate and efficient balancing of hdronic heating or cooling sstems. The GRINNE Groove-b-Groove Model CB00 Valve, available sizes 65 to 300 (2 1 2" to 12"), is composed of cast iron. The CB00 valve serves 5 functions: OD H Part Number CB002504 CB007604 CB003004 CB004004 CB001394 CB005004 CB001654 CB006004 CB00004 CB001104 CB001204 Pipe Size Dimensions H Approx. Refer to back cover for countr-specific contact information 113 imits PN/ C PSI/ F 65 73.0 290.6 17.5.5 20.7/150 u { u ~ ~ { u z u { z z { } š z u u ~ ~ { u z u { z z 65 76.1 290.6 17.5.5 20.7/150 0.9 311.2 203.2 12.5 20.7/150 z z u u { u z z ~ ~ u z u { u ~ ~ ~ u z z 100 114.3 349.3 239. 20.5 20.7/150 z š { u u { u z { u ~ z z 125 139.7 400.0 22.7 32.0 20.7/150 u } z u { u z { u ~ z z 125 141.3 400.0 22.7 32.0 20.7/150 } š } u u u u { z z 150 165.1 479.6 25. 43.5 20.7/150 150 16.3 479.6 25. 43.5 20.7/150 } } u } u u u { z z u } z u } z u ~ ~ u z z 200 219.1 600.2 46.4 116.0 20.7/150 u { u { u z { } u z z 250 273.1 730.3 479.6 171.0 20.7/150 300 323.9 49.4 514.4 136.0 20.7/150 u { z z u ~ ~ u z z Handwheel Turns See circuit balancing valve specifications on pages 111. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 12 12 12

u z Model CB00 Circuit Balancing Valves Flanged Ends, PN16/PN10 Tech Data Sheet: G450 The GRINNE Model CB00 Balancing Valve provides features for achieving accurate and efficient balancing of hdronic heating or cooling sstems. One valve serves five functions: throttling, measuring (pressure and temperature), positive shutoff, draining, and filling. The GRINNE Flange-b-Flange Model CB00 Valve, available in sizes 65 to 300 (2 1 2" to 12"), is composed of cast iron. The CB00 valve serves 5 functions: D H Part Number CB002506 CB003006 CB004006 CB005006 CB006006 CB00006 CB001106 CB001206 Pipe Size Dimensions H D Approx. imits PN/ C PSI/ F 65 73.0 290 1 15 13.5 16/150 u { u ~ { u ~ { u z u { z z z z u u { u u } z z 0.9 310 203 200 1.0 16/150 ~ ~ u z u u ~ u { } u } z z 100 114.3 350 240 220 2.0 16/150 u } z u { u u u z z 125 141.3 400 23 250 40.5 16/150 150 16.3 40 25 25 51.5 16/150 } } u } u u u z u z z z u } z u } u ~ z u ~ ~ u z z 200 219.1 600 467 340 129.5 16/150 u { u { u u ~ z u z z 250 273.1 730 40 405 196.0 16/150 u { z z u u z u u z z 300 323.9 50 515 460 264.0 16/150 Handwheel Turns See circuit balancing valve specifications on pages 111. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 12 12 12 114 GRINNE reserves the right to change the contents without notice. www.grinnell.com

u z Model CB00 Circuit Balancing Valves Flanged Ends, ANSI Class 125# Tech Data Sheet: G450 The GRINNE Model CB00 Balancing Valve provides features for achieving accurate and efficient balancing of hdronic heating or cooling sstems. One valve serves five functions: throttling, measuring (pressure and temperature), positive shutoff, draining, and filling. The GRINNE Flange-b-Flange Model CB00 Valve, available in sizes 65 to 300 (2 1 2" to 12"), is composed of cast iron. The CB00 valve serves 5 functions: D H Part Number CB002503 CB003003 CB004003 CB005003 CB006003 CB00003 CB001103 CB001203 Pipe Size Dimensions H D Approx. imits PN/ C PSI/ F 65 73.0 290 1 15 13.5 16/150 u { u ~ { u ~ { u z u { z z z z u u { u u } z z 0.9 310 203 200 1.0 16/150 ~ ~ u z u u ~ u { } u } z z 100 114.3 350 240 220 2.0 16/150 u } z u { u u u z z 125 141.3 400 23 250 40.5 16/150 150 16.3 40 25 25 51.5 16/150 } } u } u u u z u z z z u } z u } u ~ z u ~ ~ u z z 200 219.1 600 467 340 129.5 16/150 u { u { u u ~ z u z z 250 273.1 730 40 405 196.0 16/150 300 323.9 50 515 45 264.0 16/150 u { z z u u z u u z z See circuit balancing valve specifications on pages 111. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Handwheel Turns 12 12 12 Refer to back cover for countr-specific contact information 115

u { { { Model CB00 Circuit Balancing Valves Solder Ends Tech Data Sheet: G450 The GRINNE Model CB00 Balancing Valve provides features for achieving accurate and efficient balancing of hdronic heating or cooling sstems. One valve serves five functions: throttling, measuring (pressure and temperature), positive shutoff, draining and filling. The GRINNE Solder-b-Solder Model CB00 Valve, available in sizes 15 to 50 ( 1 2" to 2"), is composed of zinc retaining brass H Pipe Size Dimensions H Approx. imits PN/ C PSI/ F 15 21.3.9 114.3 0.6 16/150 u ~ z u ~ u u ~ z z u z u ~ u } u ~ z z 20 26.9 96. 115. 0.6 16/150 u z ~ u z ~ u } z z 25 33.7 109.5 119.1 1.0 16/150 32 42.4 12.5 136.7 1.4 16/150 u } } u } u z z u z z 40 4.3 141.2 13.2 1.7 16/150 u u } u ~ ~ z u z z u z { } u } u u } z z 50 60.3 166.6 147.6 2.6 16/150 Handwheel Turns See circuit balancing valve specifications on pages 111. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 116 GRINNE reserves the right to change the contents without notice. www.grinnell.com

~ u The insulation shells have a CFC-free inner core made of polurethane foam with a 1.5 (0.06") plastic coat. It consists of two double shells which are tightened b two metal straps. Available for sizes 15 200 ( 1 2" "). Specif size and endconnection tpe. u ~ u { u z { u u z u z u z u } z { u } u ~ u z z u z u u { u u } } z u } u { { u u ~ u ~ u z { u u ~ u { u z { ~ u { u z u { u u { u } u } u { z z u u } u z u { u ~ ~ u u } u u u ~ u } z ~ u u ~ u ~ u } } } u } u { z u } u { z u u } { u } z u z u Pipe Size Dimensions Approx. D H 15 21.3 69 136 13 0.15 20 26.9 77 143 195 0.1 25 33.7 5 151 243 0.22 32 42.4 97 172 254 0.20 40 4.3 105 15 250 0.33 50 60.3 120 209 276 0.43 65 73.0 260 410 505 3.06 0.9 20 415 530 3.25 100 114.3 320 520 50 5.16 125 141.3 360 560 620 5.24 150 16.3 400 600 730 5.97 200 219.1 450 760 00 - Contact a GRINNE Sales Representative for details. See circuit balancing valve specifications on pages 111. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Model CB00 Circuit Balancing Valves Insulation Kits Tech Data Sheet: G450 H H Sizes 15 50 ( 1 2" 2" ) D Sizes 65 200 ( 2 1 2" " ) D The GRINNE Model MC2 computer is a hand-held computerbalancing instrument designed to measure the flow in GRINNE Balancing Valves from 15 300 ( 1 2" 12"). The GRINNE Model MC2 computer: All results ma be saved in the hand-held computer and can be downloaded to a PC at a later time. The eas-to-operate touch button kepad protects against water and dirt particles. The hand-held computer is supplied with a rechargeable power pact. All parts of the hand-held computer are stored in a convenient carring case. Note: Onl available in select regions, contact a GRINNE Sales Representative. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Model CB00 Circuit Balancing Valves MC2 Measuring Computer Tech Data Sheet: G450 Refer to back cover for countr-specific contact information 117

j r œ ~ u ~ Figure 70607 Groove Ended Metering Station Description: complete with 2 extended pressure test points. Application: in the pipework of hot water heating and chilled water sstems to obtain flow measurements. 232 psi) 14 F to 302 F) Materials: recoended a minimum of 5 diameters of straight, valve sized, pipe on the inlet of the metering station and 3 diameters on the outlet. Signal p [mbar] 1000 9 7 6 5 4 3 2 100 9 7 6 5 4 3 2 10 9 7 6 5 DN 65 0 100 125 150 200 250 300 1000 9 7 6 5 4 1 2 3 4 5 6 7 10 2 3 4 5 6 7 100 2 3 4 5 Rate of Flow V [I/s] 4 3 2 100 9 7 6 5 4 3 2 10 9 7 6 5 4 Signal p [mbar] Part Number 7060751 7060752 7060753 7060754 7060755 7060756 7060757 706075 Pipe Size Dimensions - A B H J 65 76.1 0 10 76.1 195 { } u z u z u ~ u z u { u } 0.9 0 125.9 212 z z u z u ~ u z u u z ~ ~ u z u u { ~ u 100 114.3 0 147 114.3 234 z u { u z u } u u u z 125 139.7 0 175 139.7 262 150 165.1 0 202 165.1 29 } u } u z u { u } u u z 200 219.1 100 251 219.1 33 u } z u u u } z z u z 250 273.1 100 300 273.1 37 u { z u ~ u u { u 300 323.9 100 345 323.9 432 u { z u ~ z u u { { u For information on alternative sizes, contact a GRINNE Sales Representative. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Kv 102 120 234 335 522 70 1197 110 11 GRINNE reserves the right to change the contents without notice. www.grinnell.com

~ ~ ~ ~ Figure Venturi, Flow Meter Butt Weld with Grooved Ends GERAND Metal Identification Tag A Part Number K010000734 K01500094 K02000094 K025001144 K030001144 K045001144 K050001414 K07500164 K10000164 K12500164 K150002194 K200002194 K250002194 K300002194 K350002734 K400002734 K450002734 K500003244 DN s t u Pipe Size s t u Max. Wk Pressure Bar x ˆ Pump Capacit PM GPM Flow Range PM GPM Refer to back cover for countr-specific contact information 119 A In. Required straight pipe length Before In. After In. Approx 65 73.0 34.5 379 19-757 101.6 365 146 4.0 u { ~ u ~ u z { u { u 0 z 100 ~.9 z u 114.3 ~ u 34.5 34.5 56 24-1135 111.1 445 17.0 { z ~ u z { { u { u { u } 757 37-1514 111.1 445 17.0 ~ ~ u z { { u { u { u } 946 473-192 95.3 570 22.0 z u { u ~ ~ u { u } 1.136 567-2271 95.3 570 22.0 z } z u { u ~ ~ u { u } 1.703 51-3406 95.3 570 22.0 ~ z u { u ~ ~ u { u } 125 141.3 34.5 1.93 946-375 127 695 27.5 u } z u { u z } u ~ u { 150 } 200 250 16.3 } u } 219.1 u } 273.0 u { 34.5 34.5 34.5 2.39 1419-5677 152.4 40 336.5 { z { } u z z u { z u z u { 3.75 192-7570 152.4 40 336.5 š } u z z u { z u z u { 4.731 2365-9462 152.4 40 336.5 š } } u z z u { z u z u { 5.67 23-11355 177. 1095 43 10.5 š { z { u ~ z u { u z u 7.570 375-15140 177. 1095 43 10.5 š ~ { u ~ z u { u z u 9.463 4731-1925 177. 1095 43 10.5 š { u ~ z u { u z u 11.355 5677-22710 177. 1095 43 10.5 z š } { u ~ z u { u 13.24 6623-26495 203.2 1365 546 13.0 z š { { u z u { ~ u u { 15.140 7570-3020 203.2 1365 546 13.0 ~ š u z u { ~ u u { 17.033 516-34065 203.2 1365 546 13.0 ~ š u z u { ~ u u { 300 323.9 34.5 1.925 9462-3750 304. 1620 64 1.0 12.750 š u } z u { u z Note: End Connections: provided with butt weld and grooved ends Gauge: 114 (4 1 2") dual scale PM/GPM Bod material: Steel Approval: FM For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. z u u {

k j u ~ u u Figure 760 WYE-Strainer MATERIA SPECIFICATIONS Bod Grade 65-45-12. Colour: Red Strainer Basket 1.6 (0.06")in sizes 50 to 0 (2" to 3" 3.2 (0.16") in sizes 100 to 300 (4" to 12") For other mesh sizes contact GRINNE. Access Coupling & End Cap Bolts/Nuts hex nuts conforming to ASTM A-13 with a minimum tensile754 Bar (110,000 psi). Zinc electroplated as standard. Coupling Gasket Grade E EPDM (Designed in accordance with ASTM D-2000). Service temperature -40 C to 110 C (-40 F to 230 F). Recoended for water services, dilute acids, alkalies, oil free air and man chemical services. NOT FOR USE IN PETROEUM SERVICES. Other gasket materials on request. Drain Plug Performance Part Number Pipe Size Max. Wk Pressure* Bar x ˆ A B Drain Plug Size NPT Cv Values** PM GPM Kv Values** m3/h GPM Approx 760F00060 760F00073 760F00076 760F000 760F00114 760F00139 760F00165 760F0016 760F00219 760F00273 760F00324 50 60.3 20.7 24 192 12.7 52 45 4.5 u z { z u { } { u } u z u { 65 73.0 20.7 173 211 12.7 3 72 5.9 u { z } u u z u u z { z u { } u z u z u { u z u u z { z u 65 76.1 20.7 273 211 12.7 3 72 5.9 z z u z u { { u z u ~ } u 0.9 20.7 299 231 25.4 149 129.2 100 114.3 20.7 362 21 25.4 273 236 12.7 ~ ~ u z ~ u u } { u š z u 125 139.7 20.7 419 330 25.4 419 363 22.0 z š { u z } u u { š ~ u 150 165.1 20.7 470 367 3.1 71 621 31. } š } u z u ~ u ~ u u { š { z ~ { u 150 16.3 20.7 470 367 3.1 71 621 31. } } u } z u ~ u ~ u u { š { z ~ { u 200 219.1 20.7 610 467 3.1 946 1 52.3 u } z ~ u u z u z š } u z 250 273.1 20.7 66 559 3.1 1709 147 90.0 u { z { u u u ~ u } š { u ~ 300 323.9 20.7 762 629 3.1 260 231 120.0 u { z z u ~ u { } u { u š * Maximum working pressure is based upon the performance capabilit of the GRINNE WYE-Strainer. Maximum sstem working pressure is dependant upon the rigid couplings used for installation and the pressure capacit of the sstem components. ** Cv values are for flow of water at 16 C (60 F) For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 120 GRINNE reserves the right to change the contents without notice. www.grinnell.com } } ~ u }

u Figure S55 Tee Strainers Tech Data Sheet: G430 The Tee Strainer is designed to remove particles from pipelines where a compact, accessible strainer is needed for the protection of pumps, meters, valves, and similar mechanical equipment. The inlet and outlet ends are suitable for installation with GRINNE Couplings that provide quick and eas installation. The cover is secured b a GRINNE Figure 772 Coupling for eas access to the screen. The cover is tapped and plugged to allow for draining. The GRINNE Figure S55 Tee Strainer is rated for the following pressures: (2" 5"): 51.7 bar (750 psi) at 3 C (100 F) (6"): 4.3 bar (700 psi) at 3 C (100 F) ("): 41.7 bar (600 psi) at 3 C (100 F) (10"): 34.5 bar (500 psi) at 3 C (100 F) (12"): 27.6 bar (400 psi) at 3 C (100 F) B D The Figure S55 Tee Strainer perforated screen has the following perforations: (2" 6") = 3.2 ( 1 ") (" 12") = 4.0 ( 5 32") Note Other perforation screen sizes are available upon request. Specif particle retention size when ordering nonstandard screens. A MATERIA SPECIFICATIONS Ductile Iron Bod and Cover Standard specification for ductile iron castings (65,000 psi) (45,000 psi) (2"), minimum 12% Screen for Sizes 50 150 (2" 6") for Sizes 200 300 (" 12") Coating Performance Mechanical Products. Pipe Size Dimensions - Approx. A B D Screen Removal 50 60.3 165.0 10.0 191.0 2.7 u z { } u ~ u { u } u 65 73.0 191.0 110.0 222.0 5.0 u { { u ~ u { u { u 0.9 216.0 133.0 254.0 5.4 z z u u u u u 100 114.3 254.0 156.0 305.0 9.0 ~ ~ u u } u z u u u } z u } u } z z u z u 125 141.3 279.0 16.0 342.0 13.0 150 16.3 330.0 194.0 406.0 1.0 } } u } z u { u } z } u ~ u 200 219.1 394.0 232.0 494.0 36.0 u } u u z u ~ ~ u 250 273.0 457.0 264.0 53.0 57.0 u { u u z ~ } u 300 323.9 50.0 29.0 659.0 79.0 u { u u z u ~ { ~ u For information on alternative sizes, contact a GRINNE Sales Representative. ead time ma var b size, contact a GRINNE Sales Representative for more information. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Refer to back cover for countr-specific contact information 121

z z Figure S10 Suction Diffusers (Page 1 of 2) Tech Data Sheet: G410 The GRINNE Figure S10 Suction Diffuser is compact and rugged for direct mounting to the suction side of a pump in either a horizontal or vertical position. In addition to removing foreign particles, this diffuser also provides proper flow conditions to the pump. Where space is limited, this diffuser can be used to replace the straight pipe normall required to reduce turbulence. The GRINNE Figure S10 Suction Diffuser s permanent perforated stainless steel screen helps remove foreign particles. The inlet end is suitable for installation with GRINNE Couplings. The outlet end is provided with a 150# ANSI flat face flange. Integral straightening vanes in the diffuser outlet reduce turbulence so that stress and erosion on the pump is minimized. MATERIA SPECIFICATIONS Bod and Cover Knobs 65-45-12 for sizes 0 x 50 thru 250 x 200 (3" x 2" thru 10" x ") Stud/nuts carbon steel conforming to ASTM A 193-4, for sizes 250 x 250 (10" x 10") and larger Screen ( 5 32") perforated tpe 304 stainless steel for sizes 0 x 50 thru 150 x 150 (3" x 2" thru 6" x 6") ( 1 ") perforated tpe 304 stainless steel for sizes 200 x 125 (" x 5") and larger Coating Performance Mechanical Products. Maximum working pressure is 20.7 Bar (300 psi) at 3 C (100 F) and 11.4 Bar (165 psi) at 149 C (300 F). Note: Pressure and temperature can be limited b O-ring material. Contact a GRINNE Sales Representative. B A G D H F C E Pipe Size Dimensions - Approx. A B C D E F Screen Removal G Plug NPT H Pipe Support ID kg 50 x 50 60.3 x 60.3 114.3 114.3 169.9 155.7 25. 223. 20 20.9.6 u z { u z { ~ u ~ u } u } } u z u u u { u ~ 65 x 50 73.0 x 60.3 127.0 127.0 190.5 166.6 276.4 231.9 20 35.1 9.1 u { u z { u u { u } u } u u z u { u z 65 x 65 73.0 x 73.0 127.0 127.0 190.5 166.6 276.4 231.9 20 35.1 10.0 u { u { u u { u } u } u u z u { u z 0 x 50.9 x 60.3 139.7 139.7 214.4 17.5 293.6 244.6 20 35.1 17.2 z u u z { u u u ~ ~ { u z u } u } z u { u z z u 0 x 65.9 x 73.0 139.7 139.7 214.4 17.5 293.6 244.6 20 35.1 17.7 z u u { u u u ~ ~ { u z u } u } z u { u z z u 122 GRINNE reserves the right to change the contents without notice. www.grinnell.com

~ z ~ ~ ~ } } } } z Figure S10 Suction Diffusers (Page 2 of 2) Tech Data Sheet: G410 Pipe Size Dimensions - Approx. A B C D E F Screen Removal G Plug NPT H Pipe Support ID kg 0 x 0.9 x.9 139.7 139.7 214.4 17.5 293.6 244.6 20 35.1 1.1 z z u z u u u u ~ ~ { u z u } u } z u { u z ~ u 100 x 50 114.3 x 60.3 146.1 146.1 231.9 193. 300.0 24.0 20 35.1 21. ~ u u z { u { u { u z { u } z u u u { u z ~ u 100 x 65 114.3 x 73.0 165.1 165.1 266.2 222.3 333.5 244.6 25 35.1 22.2 ~ u u { } u } u u ~ u { z u z u } z u u z ~ u 100 x 0 114.3 x.9 165.1 173.0 265.2 222.3 333.5 292.1 25 35.1 22.7 z ~ u z u } u } u u ~ ~ u { z u z u u u z u 100 x 100 114.3 x 114.3 165.1 173.0 265.2 222.3 333.5 292.1 25 35.1 23.6 ~ ~ u ~ u } u } u u ~ ~ u { z u z u u u z u 125 x 0 141.3 x.9 165.1 165.1 266.2 222.3 333.5 292.1 25 35.1 42.6 u } z z u } u } u u ~ u { z u z u u u z ~ u 125 x 100 141.3 x 114.3 165.1 165.1 303.3 254.0 400.1 355.6 25 35.1 43.5 ~ u } z ~ u } u } u u ~ u u { ~ u u u z } u 125 x 125 141.3 x 141.3 190.5 190.5 303.3 254.0 400.1 37.0 25 35.1 45. u } z u } z { u { u u ~ u u { ~ u u u z u 150 x 0 16.3 x.9 203.2 203.2 33.1 266.7 42. 420.6 25 35.1 46.7 z } u } z u u u z u z u } u } u } u u z z u 150 x 100 16.3 x 114.3 203.2 203.2 33.1 266.7 42. 420.6 25 35.1 4.1 ~ } u } ~ u u u z u z u } u } u } u u z } u 150 x 125 16.3 x 141.3 203.2 203.2 33.1 266.7 42. 420.6 25 35.1 49.9 } u } u } z u u z u z u } u } u } u u z u 150 x 150 16.3 x 16.3 203.2 203.2 33.1 266.7 42. 420.6 25 35.1 51.2 } } u } } u } u u z u z u } u } u } u u z z u 200 x 125 219.1 x 141.3 22.6 22.6 365.3 292.1 454.2 42. 25 35.1 61.2 u } u } z u u ~ u z u { u } u u u z z u 200 x 150 219.1 x 16.3 22.6 254.0 3.9 292.1 454.2 42. 25 35.1 62.1 } u } } u } u u u z u { u } u u u z z { u 200 x 200 219.1 x 219.1 22.6 254.0 414.3 29.5 527.1 51.2 32 35.1 100.7 u } u } u u } u z u { u { u u u z u 250 x 150 273.1 x 16.3 240. 240. 393.7 303.3 465.1 42. 32 35.1 104.3 } u { } u } u ~ u ~ u u ~ u z } u u u z z u 250 x 200 237.1 x 219.1 22.6 29.5 46.4 29.5 527.1 51.2 32 35.1 107.0 u { u } u u { u ~ ~ u { u { u u u z z } u 250 x 250 273.1 x 273.1 279.4 29.5 50.0 355.6 670.1 71.1 32 35.1 155.6 u { u { u u { u ~ u } u z z u { u u z z ~ z u 300 x 200 323.9 x 219.1 22.6 22.6 49.6 29.5 527.1 51.2 32 35.1 161.9 u u } u u u } z u { u { u u u z z { u 300 x 250 323.9 x 273.1 279.4 327.2 533.4 355.6 670.1 71.1 32 35.1 161.9 u u { u u u ~ u } u z z u { u u z z { u 300 x 300 323.9 x 323.9 304. 304. 560.3 37.4 665.0 71.1 32 35.1 161.9 u u u u u } u } u z u { u u z z { u 350 x 250 355.6 x 273.1 279.4 279.4 571.5 355.6 670.1 71.1 32 35.1 229.9 ~ ~ u u { u u u ~ u } u z z u { u u z { u 350 x 300 355.6 x 323.9 304. 304. 56.5 37.4 665.0 77.4 32 35.1 272.6 ~ ~ u u u u u z u } u z u u u z } u 350 x 350 355.6 x 355.6 355.6 355.6 635.0 444.5 704.9 41.5 50 35.1 320.2 ~ ~ ~ u ~ ~ u ~ u u { u { u { z z u z u u z { } u 400 x 350 406.4 x 355.6 355.6 355.6 660.4 444.5 70.2 77.4 50 35.1 340.1 } ~ } u ~ u ~ u ~ u } u { u { u z u u u z { u For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Refer to back cover for countr-specific contact information 123

Figure 7550 Expansion Joint (Page 1 of 6) Tech Data Sheet: G460 Ordering Procedure GRINNE Mechanical Products are available globall through a network of distribution centres. Visit www.grinnell.com for the nearest distributor. When placing an order, indicate the full product name. Use the worksheet shown below to specif information required for ordering expansion joints. Specif quantit, nominal pipe size, (ANSI or ), figure number (Figure 7550 Flexible Coupling), and tpe of gasket: Pipe Size 32 to 400 (1 1 4 to 16 ): Pipe Finish Black Galvanised Stainless Steel GRINNE Grooved Expansion Joints are customdesigned, thermal movement solutions that utilize the proven design characteristics of GRINNE Flexible Couplings. Expansion joints are designed to be used in both hot and cold applications. When pipe heats up, the expansion joint contracts to absorb the thermal expansion of the pipe. When pipe cools down, the expansion joint expands to absorb the thermal contraction of the pipe. The expansion joints are factor fabricated and calibrated to the specific thermal movement conditions of the piping runs. The joints are manufactured from machined grooved nipples and GRINNE Flexible Couplings, providing dependable, high pressure performance. Expansion Joints should be anchored and guided in accordance with standard industr practices. Refer to the appropriate coupling data sheet for pressure/temperature ratings and materials of construction. Nipples are manufactured from standard wall, A 53B black steel pipe. Figure 7550 Expansion joints are custom designed to our specifications. Contact GRINNE Mechanical Services for additional information. Coupling Finish Orange Paint RA Red Galvanised Stainless Steel Gasket Material* Grade E EPDM Grade T Nitrile Grade O Fluoroelastomer Grade Silicone Factor Preset Full Expanded Full Compressed Intermediate** % Total Required Movement: 25.4 31. 3.1 44.5 1.00" 1.25" 1.50" 1.75" * These products are assembled with a silicone-based lubricant. ** For intermediate factor preset indicate percentage of movement from compressed position. 124 GRINNE reserves the right to change the contents without notice. www.grinnell.com

u ` r  a Ÿ Figure 7550 Expansion Joints Dimensions for End Elevation View Figure 7550 Expansion Joint (Page 2 of 6) Tech Data Sheet: G460 Pipe Size Dimensions - Coupling Movement Y Coupling ength W Overall Width Capabilit 32 42.4 106.4 247.7 3.1 u } } ~ u u { u 40 4.3 112. 244.5 3.1 u ~ u ~ ~ u } u u z { ~ u u { u 50 60.3 124.0 276.2 3.1 65 73.0 139.7 273.1 3.1 u { u u { u z z u } u u { u 0.9 165.1 29.5 3.1 100 114.3 196.9 32.6 6.35 ~ ~ u { u { z { u 125 141.3 247.7 362.0 6.35 u } z u { ~ u u 150 16.3 271.5 393.7 6.35 } } u } u } u u 200 219.1 344.4 463.6 6.35 u } z u } u u 250 273.0 416.1 511.2 6.35 u { } u z u u 300 323.9 479.6 56.3 6.35 u { u u z { u 350 355.6 517.7 612. 6.35 ~ ~ u u z ~ u u 400 406.4 575.1 707.9 6.35 } } u u } ~ { u { u Refer to Technical Data Sheet G460 for additional dimensions and information. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. ª ««««² ª ª «¾ Ç È À Â É Á Ê Ë Ê Á  ª «ª ««± ª ² ª ª ««³ «± ² «µ Figure 7550 Expansion Joints Retaining Bracket Detail ½ ¾ À Á  Á Â Ã Ä ½ À Å Æ ¾ d º q k i ¹ h ` i h i g Figure 7550 Expansion Joints Tpical Installation k i b œ ` e d i m b ` f q _ h i ¹ f h m d ¹ k i b œ ` e» i ` g h i b _ f m d m ¼ Refer to back cover for countr-specific contact information 125

_ Ì º } Figure 7550 Expansion Joint (Page 3 of 6) Tech Data Sheet: G460 Pipe Size ANSI Figure 7550-1 Expansion Joints - 25.4 (1" ) Total Movement ength Dimensions for Side Elevation View 32 42.4 u } } 40 4.3 u 50 60.3 u z { Flexible* Coupling Figure / Quantit 705 / 705 / 705 / X Coupling Height Z Tie ocation Compressed ength Expanded ength Total Movement Capabilit Approx. 65.02 31.75 676.27 701.67 25.40 11. u } u } u } { u } u 69.5 31.75 676.27 701.67 25.40 12.7 u { u } u } { u } u 2.55 31.75 676.27 701.67 25.40 14.1 z u u } u } { u } u z 65 73.0 93.73 31.75 676.27 701.67 25.40 16. 705 / u { z u } u } u } { u } u z { 0.9 111.25 31.75 676.27 701.67 25.40 22.2 705 / z z u ~ u z u } u } { u } u ~ 100 114.3 144.53 31.75 444.50 469.90 25.40 16.3 705 / 4 ~ ~ u u } u { u u u z } 125 141.3 174.75 31.75 444.50 469.90 25.40 24.0 705 / 4 u } z } u u { u u u z 150 16.3 201.6 31.75 444.50 469.90 25.40 26. 705 / 4 } } u } { u ~ u { u u u 200 219.1 25.3 34.93 4.95 511.17 25.40 47.2 705 / 4 u } u u z { u u u ~ 250 273.0 322.33 34.93 546.10 571.50 25.40 1.2 705 / 4 u { u } u z { u u u { 300 323.9 u { 705 / 4 379.4 34.93 546.10 571.50 25.40 106.6 ~ u ~ u z { u u u z 350 355.6 423.42 3.10 57.40 612.77 25.40 13.4 707 / 4 ~ ~ u } u } { u z u ~ u u z 400 406.4 47.2 3.10 612.77 63.17 25.40 16.2 707 / 4 } } u u z u ~ u u u z { * 32 to 200 (1 1 4" - ") Figure 405 Stainless Steel Couplings available upon request. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 126 GRINNE reserves the right to change the contents without notice. www.grinnell.com

_ Ì º Figure 7550 Expansion Joint (Page 4 of 6) Tech Data Sheet: G460 Pipe Size ANSI Figure 7550-13 Expansion Joints - 31. (1 1 4" ) Total Movement ength Dimensions for Side Elevation View 32 42.4 u } } 40 4.3 u 50 60.3 u z { Flexible* Coupling Figure / Quantit 705 / 10 705 / 10 705 / 10 X Coupling Height Z Tie ocation Compressed ength Expanded ength Total Movement Capabilit Approx. 65.02 31.75 796.92 2.67 31.75 14.1 u } u z u z { z u } u z 69.5 31.75 796.92 2.67 31.75 15.0 u { u z u z { z u } u z z 2.55 31.75 796.92 2.67 31.75 16. z u u z u z { z u } u z { 65 73.0 93.73 31.75 796.92 2.67 31.75 20.4 705 / 10 u { z u } u z u z { z u } u ~ 0.9 111.25 31.75 796.92 2.67 31.75 26. 705 / 10 z z u ~ u z u z u z { z u } u 100 114.3 144.53 31.75 50.00 539.75 31.75 19.5 705 / 5 ~ ~ u u } u u u u ~ z 125 141.3 174.75 31.75 50.00 539.75 31.75 29.0 705 / 5 u } z } u u u u u } ~ 150 16.3 201.6 31.75 50.00 539.75 31.75 31. 705 / 5 } } u } { u ~ u u u u { 200 219.1 25.3 34.93 55.0 590.55 31.75 56.7 705 / 5 u } u u z { u z u u 250 273.0 322.33 34.93 622.30 654.05 31.75 97.5 705 / 5 u { u } u z { ~ u u { u 300 323.9 u { 705 / 5 379.4 34.93 622.30 654.05 31.75 127.5 ~ u ~ u z { ~ u u { u 350 355.6 423.42 3.10 673.10 704.5 31.75 13.4 707 / 5 ~ ~ u } u } { u } u { u { u z } 400 406.4 47.2 3.10 69.50 730.25 31.75 16.2 707 / 5 } } u u z u { u u { u ~ ~ * 32 to 200 (1 1 4" - ") Figure 405 Stainless Steel Couplings available upon request. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Refer to back cover for countr-specific contact information 127

_ Ì º Figure 7550 Expansion Joint (Page 5 of 6) Tech Data Sheet: G460 Pipe Size ANSI Figure 7550-15 Expansion Joints - 3.1 (1 1 2" ) Total Movement ength Dimensions for Side Elevation View 32 42.4 u } } 40 4.3 u 50 60.3 u z { Flexible* Coupling Figure / Quantit 705 / 12 705 / 12 705 / 12 X Coupling Height Z Tie ocation Compressed ength Expanded ength Total Movement Capabilit Approx. 65.02 31.75 917.57 955.6 3.10 16. u } u z } u z { u } u z { 69.5 31.75 917.57 955.6 3.10 17.7 u { u z } u z { u } u z 2.55 31.75 917.57 955.6 3.10 19.5 z u u z } u z { u } u ~ z 65 73.0 93.73 31.75 917.57 955.6 3.10 23.6 705 / 12 u { z u } u z } u z { u } u 0.9 111.25 31.75 917.57 955.6 3.10 31.3 705 / 12 z z u ~ u z u z } u z { u } u } 100 114.3 144.53 31.75 571.50) 609.60) 3.10 22.7) 705 / 6 ~ ~ u u } u u ~ u u 125 141.3 174.75 31.75 571.50 609.60 3.10 33.6 705 / 6 u } z } u u u ~ u u { ~ 150 16.3 201.6 31.75 571.50 609.60 3.10 36.7 705 / 6 } } u } { u ~ u u ~ u u 200 219.1 25.3 34.93 631.2 669.93 3.10 65. 705 / 6 u } u u z { ~ u { } u z { u ~ 250 273.0 322.33 34.93 69.50 736.60 3.10 113. 705 / 6 u { u } u z { { u u u 300 323.9 u { 705 / 6 379.4 34.93 69.50 736.60 3.10 14. ~ u ~ u z { { u u u z 350 355.6 423.42 3.10 75.2 796.93 3.10 192. 707/ 6 ~ ~ u } u } { u u { z u z { u ~ 400 406.4 47.2 3.10 74.22 22.32 3.10 232.2 707 / 6 } } u u z u z u { z u z { u * 32 to 200 (1 1 4" - ") Figure 405 Stainless Steel Couplings available upon request. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 12 GRINNE reserves the right to change the contents without notice. www.grinnell.com

_ Ì º u u Figure 7550 Expansion Joint (Page 6 of 6) Tech Data Sheet: G460 Pipe Size ANSI Figure 7550-75 Expansion Joints - 44.5 (1 3 4" ) Total Movement ength Dimensions for Side Elevation View 32 42.4 u } } 40 4.3 u 50 60.3 u z { Flexible* Coupling Figure / Quantit 705 / 14 705 / 14 705 / 14 X Coupling Height Z Tie ocation Compressed ength Expanded ength Total Movement Capabilit Approx. 65.02 31.75 103.22 102.67 44.45 19.0 u } u ~ u { ~ u } u { ~ 69.5 31.75 103.22 102.67 44.45 20.4 u { u ~ u { ~ u } u { ~ 2.55 31.75 103.22 102.67 44.45 22.2 z u u ~ u { ~ u } u { ~ 65 73.0 93.73 31.75 103.22 102.67 44.45 27.2 705 / 14 u { z u } u ~ u { ~ u } u { } 0.9 111.25 31.75 103.22 102.67 44.45 35. 705 / 14 z z u ~ u z u ~ u { ~ u } u { { 100 114.3 144.53 31.75 635.00 679.45 44.45 25.9 705 / 7 ~ ~ u u } u u } u { u { { 125 141.3 174.75 31.75 635.00 679.45 44.45 3.1 705 / 7 u } z } u u u } u { u { ~ 150 16.3 201.6 31.75 635.00 679.45 44.45 41.7 705 / 7 } } u } { u ~ u u } u { u { 200 219.1 25.3 34.93 704.5 749.30 44.45 75.3 705 / 7 u } u u z { { u { u u { } } 250 273.0 322.33 34.93 774.70 19.15 44.45 130.2 705 / 7 u { u } u z { z u z u { { 300 323.9 u { 705 / 7 379.4 34.93 774.70 19.15 44.45 170.1 ~ u ~ u z { z u z u { z { 350 355.6 423.42 3.10 44.55 9.00 44.45 220.5 707 / 7 ~ ~ u } u } { u z z u z u u { ~ } 400 406.4 47.2 3.10 69.95 914.40 44.45 264.4 707 / 7 } } u u z u z ~ u z } u u { z * 32 to 200 (1 1 4" - ") Figure 405 Stainless Steel Couplings available upon request. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Refer to back cover for countr-specific contact information 129

Ñ á â à Figure RXAG Expansion Joint MATERIA SPECIFICATIONS Bod Bellow ã Part Number RXAG034 RXAG042 RXAG04 RXAG060 RXAG073 RXAG076 RXAG09 RXAG114 RXAG139 RXAG141 RXAG165 RXAG16 RXAG219 RXAG273 Pipe Size Max. Wk Pressure Bar psi A B Rated Movement Spring Rate N/ bs/in. Approx. 25 33.7 16.0 525.9 +10 / -70 12.2 4. Í Í Î Ï Í Ð Ñ Ï Ò Ñ Ò Î Ó Ô Ï Î Ð Ò Õ Ò Î Ï Ö Ø Ñ Î Ô Ó Ó Ö Î Ô Í Ò Î Ó 32 42.4 16.0 525 101.6 +10 / -70 12.5 6.0 Í Ù Ú Í Î Ó Ó Ò Ñ Ï Ò Ñ Ò Î Ó Ô Û Î Ò Ò Õ Ò Î Ï Ö Ø Ñ Î Ô Ó Ô Í Î Û Í Ï Î Ñ 40 4.3 16.0 525 114.3 +10 / -70 5.2 7.3 Í Ù Ü Í Î Ö Ò Ò Ñ Ï Ò Ñ Ò Î Ó Ô Û Î Ð Ò Õ Ò Î Ï Ö Ø Ñ Î Ô Ó Ñ Ö Î Ô Í Ó Î Í 50 60.3 16.0 525 114.3 +10 / -70 15.2 7. Ñ Ñ Î Ï Ô Ð Ñ Ï Ò Ñ Ò Î Ó Ô Û Î Ð Ò Õ Ò Î Ï Ö Ø Ñ Î Ô Ó Ý Ó Î Ý Í Ô Î Ñ 65 73.0 16.0 525 127.0 +10 / -70 22.1 10.3 Ù Ü Ñ Î Ý Ô Ð Ñ Ï Ò Ñ Ò Î Ó Ô Ð Î Ò Ò Õ Ò Î Ï Ö Ø Ñ Î Ô Ó Í Ñ Ó Î Ñ Ñ Ñ Î Ô 65 76.1 16.0 525 127.0 +10 / -70 22.1 10.3 Ô Ó Þ Í ß ß Ï Î Ò Ò Ò Ñ Ï Ò Ñ Ò Î Ó Ô Ð Î Ò Ò Õ Ò Î Ï Ö Ø Ñ Î Ô Ó Í Ñ Ó Î Ñ Ñ Ñ Î Ô 0.9 16.0 525 16.3 +10 / -70 2.5 14.6 Ï Ï Î Ð Ò Ò Ñ Ï Ò Ñ Ò Î Ó Ô Ó Î Ó Ï Õ Ò Î Ï Ö Ø Ñ Î Ô Ó Í Ó Ñ Î Ô Ï Ñ Î Ñ 100 114.3 16.0 525 177. +10 / -70 40.2 16.3 Û Û Î Ð Ò Ò Ñ Ï Ò Ñ Ò Î Ó Ô Ô Î Ò Ò Õ Ò Î Ï Ö Ø Ñ Î Ô Ó Ñ Ñ Ö Î Ð Ï Ð Î Ö 125 139.7 16.0 525 219.1 +10 / -70 49.5 22.3 Í Ï Ö Þ Ô ß ß Ð Î Ð Ò Ò Ñ Ï Ò Ñ Ò Î Ó Ô Ý Î Ó Ï Õ Ò Î Ï Ö Ø Ñ Î Ô Ó Ñ Ý Ñ Î Ô Û Ö Î Ñ 125 141.3 16.0 525 219.1 +10 / -70 49.5 22.3 Ð Ð Î Ð Ó Ï Ñ Ï Ò Ñ Ò Î Ó Ô Ý Î Ó Ï Õ Ò Î Ï Ö Ø Ñ Î Ô Ó Ñ Ý Ñ Î Ô Û Ö Î Ñ 150 165.1 16.0 525 273.0 +10 / -70 59.4 30.6 Í Ó Ð Þ Í ß ß Ó Î Ð Ò Ò Ñ Ï Ò Ñ Ò Î Ó Ô Í Ò Î Ô Ð Õ Ò Î Ï Ö Ø Ñ Î Ô Ó Ï Ï Ö Î Ñ Ó Ô Î Ð 150 16.3 16.0 525 273.0 +10 / -70 59.4 30.6 Ó Ó Î Ó Ñ Ð Ñ Ï Ò Ñ Ò Î Ó Ô Í Ò Î Ô Ð Õ Ò Î Ï Ö Ø Ñ Î Ô Ó Ï Ï Ö Î Ñ Ó Ô Î Ð 200 219.1 16.0 525 323.9 +10 / -70 117.3 44.4 Ý Ý Î Ó Ñ Ð Ñ Ï Ò Ñ Ò Î Ó Ô Í Ñ Î Ô Ð Õ Ò Î Ï Ö Ø Ñ Î Ô Ó Ó Ó Ö Î Ý Ö Ô Î Ö 250 273.0 16.0 525 - - - - Í Ò Í Ò Î Ô Ð Ò Ñ Ï Ò Ñ Ò Î Ó Ô Ø Ø Ø Ø Note: recoended for mounting with GRINNE Rigid couplings For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 130 GRINNE reserves the right to change the contents without notice. www.grinnell.com

á â Ñ à Figure AG Expansion Joint MATERIA SPECIFICATIONS Bellow Pipe Ends Internal Sleeves ã Part Number AG0034 AG0042 AG004 AG0060 AG0073 AG0076 Pipe Size Max. Wk Pressure Bar psi A B Rated Movement Spring Rate N/ bs/in. Approx. 25 33.7 16.0 200 39 +20 / -20 14 0.4 Í Í Î Ï Í Ð Ñ Ï Ò Ô Î Ý Ô Í Î Ð Û Õ Ò Î Ô Ö Ø Ò Î Ô Ö Ý Ò Ò Î Ö 32 42.4 16.0 205 46 +20 / -20 16 0.5 Í Ù Ú Í Î Ó Ó Ò Ñ Ï Ò Ý Î Ò Ô Í Î Ý Í Õ Ò Î Ô Ö Ø Ò Î Ô Ö Ö Í Í Î Ñ 40 4.3 16.0 234 5 +25 / -25 26 0. Í Ù Ü Í Î Ö Ò Ò Ñ Ï Ò Ö Î Ñ Í Ñ Î Ñ Ý Õ Ò Î Ö Ý Ø Ò Î Ö Ý Í Û Ý Í Î Ô 50 60.3 16.0 276 69 +30 / -30 22 1.3 Ñ Ñ Î Ï Ô Ð Ñ Ï Ò Í Ò Î Ý Ô Ñ Î Ô Ñ Õ Í Î Í Ý Ø Í Î Í Ý Í Ñ Ó Ñ Î Ý 65 73.0 16.0 261 7 +30 / -30 24 1.6 Ù Ü Ñ Î Ý Ô Ð Ñ Ï Ò Í Ò Î Ñ Ý Ï Î Û Ï Õ Í Î Í Ý Ø Í Î Í Ý Í Ï Ô Ï Î Û 65 76.1 16.0 261 7 +30 / -30 24 1.6 Ô Ó Þ Í ß ß Ï Î Ò Ò Ò Ñ Ï Ò Í Ò Î Ñ Ý Ï Î Û Ï Õ Í Î Í Ý Ø Í Î Í Ý Í Ï Ô Ï Î Û Note: recoended for mounting with GRINNE Rigid couplings For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Refer to back cover for countr-specific contact information 131

ä á â à à Figure ANS Expansion Joint ã MATERIA SPECIFICATIONS Bellow Ws No 1.4541 Pipe Ends Part Number ANS009 ANS0114 ANS0139 ANS0141 ANS0165 ANS016 ANS0219 Pipe Size Max. Wk Pressure Bar psi A B Rated Movement Spring Rate N/ bs/in Approx. 0.9 16.0 205 104 +20 / -20 46 1.9 Ï Ï Î Ð Ò Ò Ñ Ï Ò Ý Î Ò Ô Û Î Ò Ö Õ Ò Î Ô Ö Ø Ò Î Ô Ö Ñ Ó Ï Û Î Í 100 114.3 16.0 200 127 +20 / -20 49 2.4 Û Û Î Ð Ò Ò Ñ Ï Ò Ô Î Ý Ô Ð Î Ò Ò Õ Ò Î Ô Ö Ø Ò Î Ô Ö Ñ Ý Ò Ð Î Ï 125 139.7 16.0 210 155 +25 / -25 93 3.2 Í Ï Ö Þ Ô ß ß Ð Î Ð Ò Ò Ñ Ï Ò Ý Î Ñ Ô Ó Î Í Ò Õ Ò Î Ö Ý Ø Ò Î Ö Ý Ð Ï Í Ô Î Í 125 141.3 16.0 210 155 +25 / -25 93 3.2 Ð Ð Î Ð Ó Ï Ñ Ï Ò Ý Î Ñ Ô Ó Î Í Ò Õ Ò Î Ö Ý Ø Ò Î Ö Ý Ð Ï Í Ô Î Í 150 165.1 16.0 245 14 +25 / -25 3 5.0 Í Ó Ð Þ Í ß ß Ó Î Ð Ò Ò Ñ Ï Ò Ö Î Ó Ð Ô Î Ñ Û Õ Ò Î Ö Ý Ø Ò Î Ö Ý Û Ô Û Í Í Î Ò 150 16.3 16.0 245 14 +25 / -25 3 5.0 Ó Ó Î Ó Ñ Ð Ñ Ï Ò Ö Î Ó Ð Ô Î Ñ Û Õ Ò Î Ö Ý Ø Ò Î Ö Ý Û Ô Û Í Í Î Ò 200 219.1 16.0 275 235 +25 / -25 9.7 Ý Ý Î Ó Ñ Ð Ñ Ï Ò Í Ò Î Ý Ï Ö Î Ñ Ð Õ Ò Î Ö Ý Ø Ò Î Ö Ý Ð Ò Ý Í Ö Î Í Note: recoended for mounting with GRINNE Rigid couplings For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Figure FTU Rubber Bellows ISO R7 Threaded MATERIA SPECIFICATIONS Bellow Coupling Part Number FTU020E FTU025E Pipe Size Max. Wk Pressure Bar psi A Axial Movement ateral Movement Max. Deflection Approx. 20 26.9 10.0 200 +6 / -22 +22 2.1 45 Ú Í Î Ò Ð Ò Í Ð Ò Ô Î Ý Ô Õ Ò Î Ñ Û Ø Ò Î Ý Ô Õ Ò Î Ý Ô Û Î Ó 25 33.7 10.0 200 +6 / -22 +22 2.5 Í Í Î Ï Í Ð Í Ð Ò Ô Î Ý Ô Õ Ò Î Ñ Û Ø Ò Î Ý Ô Õ Ò Î Ý Ô 45 Ð Î Ð FTU032E FTU040E 32 42.4 10.0 200 +6 / -22 +22 3.2 Í Ù 45 Ú Í Î Ó Ó Ò Í Ð Ò Ô Î Ý Ô Õ Ò Î Ñ Û Ø Ò Î Ý Ô Õ Ò Î Ý Ô Ô Î Í 40 4.3 10.0 200 +6 / -22 +22 3.5 Í Ù 45 Ü Í Î Ö Ò Ò Í Ð Ò Ô Î Ý Ô Õ Ò Î Ñ Û Ø Ò Î Ý Ô Õ Ò Î Ý Ô Ô Î Ô Note: Max. working temperature: +90 C maximum Vacuum: 405 Hg For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 132 GRINNE reserves the right to change the contents without notice. www.grinnell.com

Figure FSF Flanged Rubber Bellows MATERIA SPECIFICATIONS Flange with hardened steel flange ring. Bellow à Part Number FSF0050E FSF0065E FSF000E FSF0100E FSF0125E FSF0150E Pipe Size Max. Wk Pressure Bar å æ ç Flange Dimension A Axial Movement ateral Movement Max. Deflection Approx. 50 60.3 16.0 130 +20 / -30 +20 3. Ñ Ñ Î Ï Ô Ð Ñ Ï Ò PN10/16 Ð Î Í Ñ Õ Ò Î Ô Ö Ø Í Î Í Ý Õ Ò Î Ô Ö 35 Ý Î Û 65 76.1 16.0 130 +20 / -30 +20 4.7 Ô Ó Þ Í ß ß Ï Î Ò Ò Ò Ñ Ï Ò PN10/16 Ð Î Í Ñ Õ Ò Î Ô Ö Ø Í Î Í Ý Õ Ò Î Ô Ö 35 Í Ò Î Û 0.9 16.0 130 +20 / -30 +20 5.1 Ï Ï Î Ð Ò Ò Ñ Ï Ò PN10/16 Ð Î Í Ñ Õ Ò Î Ô Ö Ø Í Î Í Ý Õ Ò Î Ô Ö 35 Í Í Î Ñ 100 114.3 16.0 130 +20 / -30 +20 7.0 Û Û Î Ð Ò Ò Ñ Ï Ò PN10/16 Ð Î Í Ñ Õ Ò Î Ô Ö Ø Í Î Í Ý Õ Ò Î Ô Ö 35 Í Ð Î Û 125 139.7 16.0 130 +20 / -30 +20.9 Í Ï Ö Þ Ô ß ß Ð Î Ð Ò Ò Ñ Ï Ò PN10/16 Ð Î Í Ñ Õ Ò Î Ô Ö Ø Í Î Í Ý Õ Ò Î Ô Ö 35 Í Ö Î Ó 150 165.1 16.0 130 +20 / -30 +20 10.6 Í Ó Ð Þ Í ß ß Ó Î Ð Ò Ò Ñ Ï Ò PN10/16 Ð Î Í Ñ Õ Ò Î Ô Ö Ø Í Î Í Ý Õ Ò Î Ô Ö 35 Ñ Ï Î Û FSF0200E FSF0250E 200 Ý 219.1 Ý Î Ó Ñ Ð Í Ð Ò Ð Î Í Ñ Õ Ò Î Ô Ö Ø Í Î Í Ý Õ Ò Î Ô Ö Ï Ï Î Ð Ñ Ï Ò Ð Î Í Ñ Õ Ò Î Ô Ö Ø Í Î Í Ý Õ Ò Î Ô Ö Ï Ï Î Ð 10.0 PN10 130 +20 / -30 +20 35 15.2 16.0 PN16 130 +20 / -30 +20 35 15.2 FSF0300E FSF1200E 250 Í Ò 273.0 Í Ò Î Ô Ð Ò Í Ð Ò Ð Î Í Ñ Õ Ò Î Ô Ö Ø Í Î Í Ý Õ Ò Î Ô Ö Ó Ö Î Û Ñ Ï Ò Ð Î Í Ñ Õ Ò Î Ô Ö Ø Í Î Í Ý Õ Ò Î Ô Ö Ó Ö Î Û 10.0 PN10 130 +20 / -30 +20 35 31.5 16.0 PN16 130 +20 / -30 +20 35 31.5 FSF1250E FSF1300E 300 Í Ñ 323.9 Í Ñ Î Ô Ð Ò Í Ð Ò Ð Î Í Ñ Õ Ò Î Ô Ö Ø Í Î Í Ý Õ Ò Î Ô Ö Ñ Í Ô Î Û Ñ Ï Ò Ð Î Í Ñ Õ Ò Î Ô Ö Ø Í Î Í Ý Õ Ò Î Ô Ö Ñ Í Ô Î Û 10.0 PN10 130 +20 / -30 +20 35 9.6 16.0 PN16 130 +20 / -30 +20 35 9.6 Note: Max. working temperature: 104 C (219.2 F) maximum Vacuum: 400 Hg For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. í î Reaction Force FSF Rubber Expansion Joints è é ê ë ë ì ë ë ë ë ò ó ë ë ó ë ë ë ô ó ë ë ì ë ë ë ò ó ë ó ë ë ô ó ë è é ô ó ë è é ô ë ë è é ì ó ë è é ì ô ó è é ì ë ë è é ë è é ö ó è é ó ë ì ë ë ô ê õ ó ö ì ë ì ö ô ë ô ó ï ð ñ Refer to back cover for countr-specific contact information 133

Figure UFBX Flexible Hoses (Page 1 of 2) Specificall designed to meet the requirements of ISO 1030 7.4.2. Applications: - Static installations (connect pipe work out of alignment) - Occasional flexing - Constant flexing - Vibration (high frequenc, low amplitude movement - compressor or pump) These products are not approved for Sprinkler applications Construction The hoses are annularl corrugated formed from butt weld rigid tube. Depending on the application, required working pressure and conditions of operation, a single or double laer of wire braid is applied externall to the hose to restrain it, increasing its abilit to withstand the pressure, increasing hoop strength and protection from abrasion. The extent of braiding, gauge and angle of la is calculated carefull to maximize performance. DOUBE BRAIDED UFBX2 SINGE BRAID UFBX1 UNBRAIDED UFBX0 MATERIA SPECIFICATIONS Hose * Braiding * Temperature Range (-32 F to 1,112 F) Hose ength 3.2 feet) * Other materials available on request Part Number DN ISO 1030 Pressure PN Hose Tpe 4 UFBX0 Max. OD In. Bend Radius Maximum Pressure Approx. Static In. Flexing In. Working Bar psi Test Bar psi Burst Bar psi Kg/M /Ft. 33.7 44 200 4.1 6.2 16.4 0.3 Í Î Ï Ï Í Î Ô Ï Ô Î Ý Ô Ð Ö Î Ð Ý Ö Î Ö Ñ Ï Ô Î Ö Ò Î Ñ UFBX1-034 25 UFBX1-042 32 UFBX1-04 40 UFBX1-060 50 UFBX1-076 65 UFBX1-09 0 50 UFBX1 63 UFBX2 2.5 UFBX0 25 UFBX1 50 UFBX2 0.5 UFBX0 25 UFBX1 50 UFBX2 0.5 UFBX0 25 UFBX1 40 UFBX2 0.5 UFBX0 25 UFBX1 40 UFBX2 0.5 UFBX0 20 UFBX1 40 UFBX2 35. 5 200 50.0 75.0 200.0 0.7 Í Î Û Í Ï Î Ï Ð Ô Î Ý Ô Ô Ñ Ð Î Ñ Í Þ Ò Ý Ô Î Ý Ñ Þ Ö Ò Ò Î Ý Ò Î Ð 37.9 5 200 76.0 114.0 304.0 1.1 Í Î Û Ö Ï Î Ï Ð Ô Î Ý Ô Í Þ Í Ò Ñ Î Ï Í Þ Ó Ð Ï Î Û Û Þ Û Ò Ö Î Í Ò Î Ô 41.4 55 250 3.4 5.1 13.6 0.4 Í Î Ó Ï Ñ Î Í Ô Ö Î Ý Û Û Ö Î Ï Ô Û Î Ò Í Ö Ô Î Ï Ò Î Ï 43.2 105 250 39.0 59.0 156.0 0.9 Í Î Ô Ò Û Î Í Ï Ö Î Ý Û Ð Ó Ð Î Ó Ý Ð Ð Î Ô Ñ Þ Ñ Ó Ñ Î Ó Ò Î Ó 45.3 105 250 57.0 5.0 22.0 1.3 Í Î Ô Ý Û Î Í Ï Ö Î Ý Û Ý Ñ Ó Î Ô Í Þ Ñ Ï Ñ Î Ý Ï Þ Ï Ò Ó Î Ö Ò Î Ö 47.9 70 250 2.4 3.6 9.6 0.7 Í Î Ý Ö Ñ Î Ô Ó Ö Î Ý Û Ï Û Î Ý Ð Ñ Î Ñ Í Ï Ö Î Ñ Ò Î Ð 50 127 250 35.0 53.0 140.0 1.2 Í Î Ö Ô Ð Î Ò Ò Ö Î Ý Û Ð Ò Ô Î Ó Ô Ó Ý Î Ô Ñ Þ Ò Ï Ò Î Ð Ò Î Ý 52.2 127 250 55.0 2.0 220.0 1.7 Ñ Î Ò Ó Ð Î Ò Ò Ö Î Ý Û Ô Ö Ô Î Ô Í Þ Í Ý Ö Î Ï Ï Þ Í Ö Ò Î Ý Í Î Í 62.1 90 350 1.0 1.5 4.0 0. Ñ Î Û Û Ï Î Ð Û Í Ï Î Ô Ý Í Û Î Ð Ñ Í Î Ý Ð Ý Î Ò Ò Î Ó 64.2 160 350 30.0 45.0 120.0 1.5 Ñ Î Ð Ï Ó Î Ï Ò Í Ï Î Ô Ý Û Ï Ð Î Í Ó Ð Ñ Î Ô Í Þ Ô Û Ò Î Ð Í Î Ò 66.3 160 350 44.0 66.0 176.0 2.3 Ñ Î Ó Í Ó Î Ï Ò Í Ï Î Ô Ý Ó Ï Ý Î Ñ Ö Ð Ô Î Ñ Ñ Þ Ð Ð Ñ Î Ô Í Î Ð 76.5 110 410 1.0 1.5 4.0 1.9 Ï Î Ò Í Û Î Ï Ï Í Ó Î Í Û Í Û Î Ð Ñ Í Î Ý Ð Ý Î Ò Í Î Ï 7.6 200 410 26.0 39.0 104.0 2. Ï Î Ò Ö Ô Î Ý Ô Í Ó Î Í Û Ï Ô Ô Î Í Ð Ó Ð Î Ó Í Þ Ð Ò Ý Î Û Í Î Ö 0.7 200 410 46.0 69.0 14.0 3.7 Ï Î Í Ý Ô Î Ý Ô Í Ó Î Í Û Ó Ó Ô Î Ñ Í Þ Ò Ò Ò Î Ý Ñ Þ Ó Ó Ý Î Ô Ñ Î Ð 9. 130 450 1.0 1.5 4.0 2.3 Ï Î Ð Û Ð Î Í Ñ Í Ô Î Ô Ñ Í Û Î Ð Ñ Í Î Ý Ð Ý Î Ò Í Î Ð 91.9 230 450 22.0 33.0.0 3.4 Ï Î Ó Ñ Ö Î Ò Ó Í Ô Î Ô Ñ Ï Í Ö Î Í Û Ô Ý Î Ó Í Þ Ñ Ô Ó Î Ï Ñ Î Ï 94.1 230 450 40.0 60.0 160.0 4.5 Ï Î Ô Ò Ö Î Ò Ó Í Ô Î Ô Ñ Ð Ý Ò Î Ñ Ý Ô Ò Î Ñ Ñ Þ Ï Ñ Ò Î Ó Ï Î Ò 134 GRINNE reserves the right to change the contents without notice. www.grinnell.com

Design twisting. Keep flexing in one plane. Shock Pressure considerabl affect hose longevit and if encountered, peak pressure must not pressure. Pressure oss To achieve the same pressure loss as in steel pipes, the diameter of the corrugated hose should be increased Design and Installation Considerations Flexing is usuall in accordance with one or a combination of the tpes of motion shown. The flex calculations help determine the length of hose required to prevent flexing below the minimum bend radius, thereb ensuring maximum reliabilit. Contact assistance with this calculation. UFBX ength Calculations Figure UFBX Flexible Hoses Vertical oop - Vertical Travel (Page 2 of 2) These drawings illustrate different length calculations necessar; Offset or Offset or ateral Movement M R M R M C Vertical oop - Horizontal Travel R M Part Number DN ISO 1030 Pressure PN Hose Tpe 0.5 UFBX0 Max. OD In. Bend Radius Maximum Pressure Approx. Static In. Flexing In. Working Bar psi Test Bar psi Burst Bar psi Kg/M /Ft. 126 200 560 0.7 1.0 2. 2. Û Î Ö Ó Ô Î Ý Ô Ñ Ñ Î Ò Ð Í Ò Î Ò Í Ð Î Í Û Ò Î Ó Í Î Ö UFBX1-114 100 UFBX1-139 125 UFBX1-16 150 UFBX1-219 200 UFBX1-273 250 16 UFBX1 25 UFBX2 0.5 UFBX0 10 UFBX1 20 UFBX2 0.5 UFBX0 10 UFBX1 20 UFBX2 - UFBX0 6 UFBX1 10 UFBX2 - UFBX0 6 UFBX1 - UFBX2 129 230 560 1.4 27.6 73.6 4.6 Ð Î Ò Ý Ö Î Ò Ó Ñ Ñ Î Ò Ð Ñ Ó Ó Î Ö Û Ò Ò Î Ï Í Þ Ò Ó Ô Î Ð Ï Î Í 132 230 560 33.0 49.5 132.0 6.4 Ð Î Ñ Ò Ö Î Ò Ó Ñ Ñ Î Ò Ð Û Ô Ý Î Ó Ô Í Ô Î Ö Í Þ Ö Í Û Î Ð Û Î Ï 151 250 710 0.7 1.0 2. 4.7 Ð Î Ö Û Ö Î Ý Û Ñ Ô Î Ö Ð Í Ò Î Ò Í Ð Î Í Û Ò Î Ó Ï Î Ñ 153 20 710 11.5 17.3 46.0 6.6 Ó Î Ò Ñ Í Í Î Ò Ñ Ñ Ô Î Ö Ð Í Ó Ó Î Ý Ñ Ð Ò Î Ö Ó Ó Ô Î Ñ Û Î Û 156 20 710 20.7 31.0 2..5 Ó Î Í Û Í Í Î Ò Ñ Ñ Ô Î Ö Ð Ï Ò Ò Î Ñ Û Û Ö Î Ó Í Þ Ñ Ò Ò Î Ö Ð Î Ô 17 290 15 0.6 0. 2.2 5.5 Ô Î Ò Í Í Í Î Û Ñ Ï Ñ Î Ò Ö Ý Î Ò Í Ñ Î Ò Ï Í Î Ö Ï Î Ô 10 320 15 11.2 16. 44. 7.7 Ô Î Ò Ö Í Ñ Î Ó Ò Ï Ñ Î Ò Ö Í Ó Ñ Î Û Ñ Û Ï Î Ô Ó Û Ö Î Ý Ð Î Ñ 13 320 15 20.0 30.0 0.0 9.9 Ô Î Ñ Ò Í Ñ Î Ó Ò Ï Ñ Î Ò Ö Ñ Ö Ò Î Í Û Ï Ð Î Í Í Þ Í Ó Ò Î Ï Ó Î Ô 232 40 1015 0.3 0.5 1.2 7.3 Ö Î Í Ï Í Î Ð Ô Ï Ö Î Ö Ó Û Î Ð Ó Î Ô Í Ý Î Ò Û Î Ö 235 435 1015 7.0 11.0 2.0 10.0 Ö Î Ñ Ð Í Ô Î Í Ï Ï Ö Î Ö Ó Í Ò Í Î Ð Í Ð Ö Î Ð Û Ò Ó Î Í Ó Î Ô 237 435 1015 10.0 15.0 40.0 13.0 Ö Î Ï Ï Í Ô Î Í Ï Ï Ö Î Ö Ó Í Û Ð Î Ò Ñ Í Ô Î Ó Ð Ý Ò Î Ñ Ý Î Ô 27 490 1220 0.3 0.4 1.0 9.2 Í Í Î Ï Ò Í Ö Î Ñ Ö Û Ý Î Ò Ï Ï Î Ó Ð Î Û Í Û Î Ð Ó Î Ñ 292 560 1220 9.6 14.4 3.4 14.7 Í Í Î Ð Ò Ñ Ñ Î Ò Ð Û Ý Î Ò Ï Í Ï Ö Î Ñ Ñ Ò Ý Î Ö Ð Ð Ó Î Ö Ö Î Ö - - - - - - - Note: The values given above are for factor braided and assembled units and are given as an aid to hose selection. For unbraided applications or if the hose is to form an assembl used at the extreme of one or more of the characteristics below, please discuss the application with our application engineering department. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Refer to back cover for countr-specific contact information 135

Ñ Í Í ä ä Ù Ù Ù Ù Î Figure HERCUES Fix Point FMAX B D D1 SW T W 2X FAZ G H Part Number T < +120 C T < +220 C 1501151 1502151 150111 150211 1501221 1502221 150121 150221 1501352 1502352 1501422 1502422 150143 150243 1501543 1502543 1501573 1502573 1501603 1502603 1501764 1502764 150194 150294 1501145 1502145 1501405 1502405 150166 150266 1501197 1502197 15073 150273 Size DN In. Fmax kn lbs H In. Dimensions - ø ù W In. In. B In. D1 In. Tpe (2 Required) 15 5 72 140 120 115 74 5 15 Ø Í Þ Í Ñ Û Ñ Î Ý Ï Ð Î Ð Í Û Î Ô Ñ Û Î Ð Ï Ñ Î Ö Í FAZ II 12/10 Ò Î Ñ Ò Í Î Ò Ï 1 5 72 140 120 115 74 5 15 FAZ II 12/10 ú Í Þ Í Ñ Û Ñ Î Ý Ï Ð Î Ð Í Û Î Ô Ñ Û Î Ð Ï Ñ Î Ö Í Ò Î Ñ Ò Í Î Ò Ï 22 5 72 140 120 115 74 5 15 FAZ II 12/10 Ü Í Þ Í Ñ Û Ñ Î Ý Ï Ð Î Ð Í Û Î Ô Ñ Û Î Ð Ï Ñ Î Ö Í Ò Î Ñ Ò Í Î Ò Ï 2 5 72 140 120 115 74 5 15 FAZ II 12/10 Ú Í Þ Í Ñ Û Ñ Î Ý Ï Ð Î Ð Í Û Î Ô Ñ Û Î Ð Ï Ñ Î Ö Í Ò Î Ñ Ò Í Î Ò Ï 35 5 5 140 140 135 92 5 15 Í Í Þ Í Ñ Û Ï Î Ï Ð Ð Î Ð Í Ð Î Ð Í Ð Î Ï Í Ï Î Ó Ñ FAZ II 12/10 Ò Î Ñ Ò Í Î Ò Ï 42 5 5 140 140 135 92 5 15 FAZ II 12/10 Ú Í Þ Í Ñ Û Ï Î Ï Ð Ð Î Ð Í Ð Î Ð Í Ð Î Ï Í Ï Î Ó Ñ Ò Î Ñ Ò Í Î Ò Ï 4 100 160 175 170 125 6 30 FAZ II 16/25 Ü Í Þ Ô Ö Ý Ï Î Ö Û Ó Î Ï Ò Ó Î Ý Ö Ó Î Ó Ö Û Î Ö Ñ Ò Î Ñ Û Ñ Î Ò Ó 54 100 160 175 170 125 6 30 Ø Í Þ Ô Ö Ý Ï Î Ö Û Ó Î Ï Ò Ó Î Ý Ö Ó Î Ó Ö Û Î Ö Ñ FAZ II 16/25 Ò Î Ñ Û Ñ Î Ò Ó 57 100 160 175 170 125 6 30 Ø Í Þ Ô Ö Ý Ï Î Ö Û Ó Î Ï Ò Ó Î Ý Ö Ó Î Ó Ö Û Î Ö Ñ FAZ II 16/25 Ò Î Ñ Û Ñ Î Ò Ó 60 100 160 175 170 125 6 30 Ñ Í Þ Ô Ö Ý Ï Î Ö Û Ó Î Ï Ò Ó Î Ý Ö Ó Î Ó Ö Û Î Ö Ñ FAZ II 16/25 Ò Î Ñ Û Ñ Î Ò Ó 76 11 115 10 205 190 150 6 30 FAZ II 16/25 Ü Ñ Þ Û Ô Ï Û Î Ð Ï Ô Î Ò Ö Ý Î Ò Ô Ô Î Û Ý Ð Î Ö Í Ò Î Ñ Û Ñ Î Ò Ó 9 11 115 10 205 190 150 6 30 Ï Ñ Þ Û Ô Ï Û Î Ð Ï Ô Î Ò Ö Ý Î Ò Ô Ô Î Û Ý Ð Î Ö Í FAZ II 16/25 Ò Î Ñ Û Ñ Î Ò Ó SW In. T Nm bf/ft 114 10 15 200 20 260 205 60 Û Ñ Þ Ñ Û Ý Ó Î Ñ Ñ Ô Î Ý Ô Í Í Î Ò Ñ Í Ò Î Ñ Û Ý Î Ò Ô FAZ II 16/25 Ò Î Ï Í Û Î Í Í 140 10 15 200 20 260 205 60 Ð Ñ Þ Ñ Û Ý Ó Î Ñ Ñ Ô Î Ý Ô Í Í Î Ò Ñ Í Ò Î Ñ Û Ý Î Ò Ô FAZ II 16/25 Ò Î Ï Í Û Î Í Í 150 30 310 200 355-275 - - Ó Ó Þ Ô Û Û Í Ñ Î Ñ Ò Ô Î Ý Ô Í Ï Î Ö Ý Ø Í Ò Î Ý Ï FAZ II 20/60 Ø Ø 200 30 330 200 404-324 - - Ý Ó Þ Ô Û Û Í Ñ Î Ö Ö Ô Î Ý Ô Í Ð Î Ö Í Ø Í Ñ Î Ô Ó FAZ II 20/60 Ø Ø 250 30 370 200 47-407 - - Í Ò Ó Þ Ô Û Û Í Û Î Ð Ô Ô Î Ý Ô Í Ö Î Í Ô Ø Í Ó Î Ò Ñ FAZ II 20/60 Ø Ø For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 136 GRINNE reserves the right to change the contents without notice. www.grinnell.com

Figure FAZ II Anchor Description is pulled into the expansion clip and expands it against the drill hole wall. corrosion-resistance class III e.g. A4 for outdoor applications and for damp rooms. Advantages/benefits distribution for high loads and small edge distances and axial spacings with filigree building components as well as secure expansion even in cracked concrete. necessar to appl the torque. Note: FAZ II Anchor is suitable onl for concrete with Rck 25 N/ 2. T H Hexagon Nut and Washer Expansion Sleeve Cone Bolt Part Number Tpe Thread Size 1761201 FAZ II 12/10 M12 1761602 FAZ II 16/25 M16 1772003 FAZ II 20/60 M20 Anchor ength In. Max. Fixture Thickness T In. Drill Hole Diameter In. Effective Anchor Depth H In. Approx. 110 10 12 70 0.096 Û Î Ï Ï Ò Î Ï Ö Ò Î Û Ô Ñ Î Ô Ó Ò Î Ñ Í Ñ 14 25 16 5 0.223 Ð Î Ý Ï Ò Î Ö Ý Ò Î Ó Ï Ï Î Ï Ð Ò Î Û Ö Í 202 60 20 100 0.421 Ô Î Ö Ð Ñ Î Ï Ó Ò Î Ô Ö Ï Î Ö Û Ò Î Ö Ñ Ý For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. Refer to back cover for countr-specific contact information 137

Ñ ä Ù Ù Figures 407GT & 407T Dielectric Waterwas Tech Data Sheet: G465 Clearflow* Fittings protect plumbing sstems through an innovative steel-toplastic design that establishes a dielectric waterwa. The dielectric fittings separate dissimilar metals in the electrolte (waterwa), eliminating the local galvanic cell. The Clearflow Fittings metal-to-metal joint design maintains external electrical continuit, thereb preventing stra current corrosion. This feature is critical when stra current is present due to intentional or non-intentional grounding of direct current (DC) sources, such as phone sstems and appliances. Fittings meet the requirements of ASTM D 4140 for continuous use at temperatures up to 110 C (230 F). Test data/results and listings b Pittsburgh Testing aborator can be provided upon request. Contact a GRINNE Sales Representative * Clearflow is a Registered Trademark of Perfection Corp. Figure 407GT Dielectric Waterwa E to E Figure 407T Dielectric Waterwa E to E Pipe Size Part Number Figure 407GT Grooved x Male Thread End to End Approx. kg Part Number Figure 407T Male Thread x Male Thread End to End Approx. kg 15 21.3 76.2 0.1 407T000212 Ü Ò Î Ý Û Ò û û Ï Î Ò Ò Î Ñ 20 26.9 76.2 0.1 407T000262 Ú Í Î Ò Ð Ò û û Ï Î Ò Ò Î Ñ 25 33.7 101.6 0.1 101.6 0.1 Í Í Î Ï Í Ð Û Î Ò Ò Î Ï 407T000342 Û Î Ò Ò Î Ï 32 42.4 101.6 0.3 101.6 0.3 Í Ù 407GT00422 407T000422 Ú Í Î Ó Ó Ò Û Î Ò Ò Î Ó Û Î Ò Ò Î Ó 40 4.3 101.6 0.4 101.6 0.4 Í Ù 407GT0042 407T00042 Ü Í Î Ö Ò Ò Û Î Ò Ò Î Ý Û Î Ò Ò Î Ý 50 60.3 101.6 0.5 101.6 0.5 Ñ Ñ Î Ï Ô Ð 407GT00602 Û Î Ò Í Î Ò 407T000602 Û Î Ò Í Î Ò 65 73.0 152.4 0.7 152.4 0.7 407GT00732 407T000732 Ü Ñ Î Ý Ô Ð Ó Î Ò Í Î Ó Ó Î Ò Í Î Ó 0.9 152.4 0.9 152.4 0.9 Ï Ï Î Ð Ò Ò 407GT0092 Ó Î Ò Ñ Î Ò 407T00092 Ó Î Ò Ñ Î Ò 100 114.3 152.4 2.0 152.4 2.0 Û Û Î Ð Ò Ò 407GT01142 Ó Î Ò Û Î Ð 407T001142 Ó Î Ò Û Î Ð See fitting specifications on page 51. For instructions on part numbers, ordering information, and availabilit, refer to page 15 or contact a GRINNE Sales Representative. 13 GRINNE reserves the right to change the contents without notice. www.grinnell.com