Product description Spotlights Downlights High-flux LED module Narrow colour temperature tolerance band Lifetime up to 5, hours Compact design Excellent thermal management NTC for temperature control High-power LED in chip-on-board technololgy Beam characteristic: 4 Uniform distribution of light Fixing holes for M3 screws Connection: Cable 3 mm Built-in LED module Cooling required Technical data Beam characteristic 4 Ambient temperature ta -3... +55 C Typ. tc point 65 C Weight.5 kg Risk group (EN 6247:28) È Standards, page 3 Colour temperatures and tolerances, page 6 Umodule SPOT P3-3 EM umodule SPOT 39,5 35,5 NTC NTC LED + LED + LED EM LED EM 8,5 4,5 5 6 2 3 4 8,5 46,5 23,5 38,5 Ø3,2,65 NTC tc Ø9 Ø28,5 2 44 2, typ. Minimal reflector diameter 2 Maximum reflector diameter Ordering data Colour temperature Type Article number 3, K LED P3-3 EM 3K 47x44 89643 4, K LED P3-3 EM 4K 47x44 896432 Packaging: 2 pieces/packaging, 36 pieces/carton Specific technical data Type Photometric Typ. luminous flux Typ. luminous flux Typ. Efficacy Colour rendering index code at 35 ma 234 at 7 ma 234 Typ. forward voltage module CRI Normal operation LED P3-3 EM 3K 47x44 83/4x9 9 lm,5 lm 38.4 V 3.4 W 68 lm/w > 8 LED P3-3 EM 4K 47x44 84/4x9, lm,68 lm 38.4 V 3.4 W 75 lm/w > 8 Emergency operation 35 ma LED P3-3 EM 3K 47x44 83/4x9 5 lm 6,2 V 2.2 W 68 lm/w > 8 LED P3-3 EM 4K 47x44 84/4x9 6 lm 6,2 V 2.2 W 75 lm/w > 8 All values for ta = 25 C, tc = 65 C. If the maximum temperature limits are exceeded, the life of the module will be greatly reduced or the module may be damaged. The temperature of the umodule SPOT at the tc point in the thermally stable state by mean of a temperature sensor or temperature-sensitive sticker as per EN 6598-. For the precise position of the tc point see the drawing above. 2 At tc = 65 C. 3 Tolerance range for optical and electrical data: ±5 %. 4 Max. permissible surge current: 3 A, duration max. µs. www.tridonic.com
Converter / controls matrix Umodule SPOT P3-3 EM in normal operation Type LCAI 5 W 35 ma one4all LCAI 3 W 7 ma one4all Converter REMOTE LCI LCI 5 W 35 ma LCI 3 W 7 ma LCCI 6 W 35 ma C35-2 4-Channel Controls IN-BUILT C35 dim C7 dim Article number 86458899 864589 246632 246634 864592 86458693 86458944 86458945 Assignable converter Assignable controls Type Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Umodule SPOT P3-3 EM 2 2 4 2 Wiring diagram converter + Emergency device Converter matrix Umodule SPOT P3-3 EM in emergency operation Type 2 W BASIC screw-fix 2 W BASIC clip-fix Converter for emergency operation 2 W ST screw-fix 2 W ST clip-fix 2 W PRO EZ-3 screw-fix 2 W PRO EZ-3 clip-fix Article number 89899859 89899866 8989986 89899868 8983 89832 Assignable converter Type Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Umodule SPOT P3-3 EM Uconverter Wiring Cable: AWG24; length 3 mm pin 2 3 4 5 6 function + (LED) - (LED) + (EM) - (EM) NTC (LED) NTC (LED) colour red black red black grey grey Product description Housing for LED module Diameter: 5 mm 2 3 4 ACCES- SORIES TALEXXaccessory Cover Spot Ordering data Typ Article number P 3-3 EM LED cover white D5 LES 9 mm 8867487 Packaging: 2 pieces/packaging, 4 pieces/carton www.tridonic.com 2
Standards EN 623 EN 6247 Photometric code Key for photometric code, e. g. 83 / 559 st digit 2 nd + 3 rd digit 4 th digit 5 th digit 6 th digit Lumen maintanance after 25% Code CRI McAdams after of the lifetime (max.6h) Colour temperature in McAdams 25% of the Code Remaining lumen 7 67 76 Kelvin x initial lifetime 7 7 % 8 77 86 (max.6h) 8 8 % 9 87 9 9 9 % Thermal design and heat sink The rated life of u products depends to a large extent on the temperature. If the permissible temperature limits are exceeded, the life of the umodule SPOT will be greatly reduced or the umodule SPOT may be destroyed. Therefore the umodule SPOT P3-3 EM needs to be mounted onto a heat sink. Tridonic s excellent thermal design for the umodule SPOT products provides the lowest thermal resistance and therefore allowing new compact designs without sacrificing quality, safety and life time. tc point, ambient temperature and lifetime The temperature at tc reference point is crucial for the light output and life time of a u product. For umodule SPOT P3-3 EM a tc temperature of 65 C has to be complied in order to achieve an optimum between heat sink requirements, light output and life time. Compliance with the maximum permissible reference temperature at the tc point must be checked under operating conditions in a thermally stable state. The maximum value must be determined under worst-case conditions for the relevant application. Mounting instruction umodule SPOT from Tridonic which have to be installed on a heat sink have to be connected with heat-conducting paste or heat conducting adhesive film and fixed with M3 screws with plastic washer. The fixing/cooling surface must be cleaned before installing the u modules to remove all dirt, dust and grease. None of the components of the umodule SPOT (substrate, LED, electronic components etc.) may be exposed to tensile or compressive stresses. EOS/ESD safety guidelines The device / module contains components that are sensitive to electrostatic discharge and may only be installed in the factory and on site if appropriate EOS/ESD protection measures have been taken. No special measures need be taken for devices/modules with enclosed casings (contact with the pc board not possible), just normal installation practice. Please note the requirements set out in the document EOS / ESD guidelines (Guideline_EOS_ESD.pdf) at: http://www.tridonic.com/com/en/technical-docs.asp Temperature control An NTC resistor is on the board of the umodule SPOT P3-3 EM to control the tc temperature during the operation. Exact position see drawing on page. The details of the 22 kω NTC (order number B5743V2223J62) you can find in the data sheet of the manufacturer AVX (Nr. NB2QØØ224). Resistance [kω] Typical heat sink surface Umodule SPOT P3-3 EM, 35 ma ta tc Rth, hs-a 25 C 65 C 4.36 K/W 3 C 65 C 3.79 K/W 4 C 65 C 2.66 K/W 5 C 65 C.53 K/W Umodule SPOT P3-3 EM, 7 ma ta tc Rth, hs-a 25 C 65 C 2.9 K/W 3 C 65 C.8 K/W 4 C 65 C.24 K/W 5 C 65 C.68 K/W Notes The actual cooling surface can differ because of the material, the structural shape, outside influences and the installation situation. A thermal connection between umodule SPOT and heat sink with heat-conducting paste or heat conducting adhesive film is absolutely necessary. Thermal behaviour storage temperature -3 85 C operating temperature -3 55 C tc max. (at typ. current) 85 C If [ma] 24 22 2 8 6 4 2 8 6 4 2 25 3 35 4 45 5 55 6 65 7 75 Temperature [ C] 6 4 2 8 6 4 2 2 3 4 5 6 7 8 9 Tc [ C] 8 85 www.tridonic.com 3
Matrix temperature Lifetime f(soldering time) for the modules Temperature Max. time Max. time without heat sink with optimized heat sink 33 C 5 s 34 C 2 s 35 C s 36 C 5 s 5 s 37 C 3 s 2 s 38 C 2 s s 39 C s 5 s The values apply for soldering without heat sink. To reduce the duration of soldering it is recommended to pre-heat the module at ta max., e.g. on a plate. Electrical supply/choice of converter umodule SPOT from Tridonic are not protected against overvoltages, overcurrents, overloads or short-circuit currents. Safe and reliable operation can only be guaranteed in conjunction with a converter which complies with the relevant standards. The use of u converters from Tridonic in combination with umodule SPOT guarantees the necessary protection for safe and reliable operation. If a converter other than Tridonic uconverter is used, it must provide the following protection: Short-circuit protection Overload protection Overtemperature protection umodule SPOT P3-3 EM must be supplied by a constant current converter. Operation with a constant voltage converter will lead to an irreversible damage of the module. Wrong polarity can damage the umodule SPOT P3-3 EM. tc temperature in C luminous flux in % lifetime in h 8 6, 25 7 8, 5 32, 8 44, 45 7 64, 5, 8 32, 65 7 5, 5 9, 8 25, 75 7 4, 5 8, www.tridonic.com 4
Relative forward voltage and relative luminous flux in normal operation / in emergency operation,5,5 rel. voltage [a. u.] rel. luminous flux [a.u.] The diagrams based on statistic values. The real values can be different. Optical characteristics Umodule SPOT P3-3 EM The optical design of the umodule SPOT product line ensures optimum homogenity for the light distribution. relative intensity Iv/Iv,max,,5,,95,9 8 6-6 4 2-5 2 3 4 5 6 7 8 current [ma] Relative forward voltage at tc = 65 C,8,6,4,2,,8,6,4,2 2 3 4 5 6 7 8 Relative luminous flux at tc = 65 C -4 - -2-3 current [ma] Umodule SPOT P3-3 EM 4 : Light distribution 2 3 4 5 6 7 8 rel. voltage [a.u.] rel. luminous flux [a.u.],4,3,2,,99,98,97 2 3 4 5 6 7 Tc [ C],4,2,,8,6,4,2,98,96,94 8 85,92 2 3 4 5 6 7 8 85 Tc [ C] -9 - -8-6 -4-2 2 4 6 8 9 www.tridonic.com 5
Coordinates and tolerances according to CIE 964 The specified colour coordinates are measured by a current impulse of 35 ma and a duration of ms. The ambient temperature of the measurement is ta = 25 C. The measurement tolerance of the colour coordinates are ±.. 3, K x y Centre,446,399,42,45,4,45,4,395,39,385,38,425,43,435,44,445 MacAdam ellipse: 4SDCM 4, K x y Centre,386,378.4.395.39.385.38.375.37.365.36.365.37.375.38.385 MacAdam ellipse: 4SDCM,45.39,455.395,46.4,465.45 norm. intensity [%] norm. intensity [%] 8 6 4 2 8 6 4 2 38 42 46 5 54 58 62 66 7 74 78 wave length [nm] 38 42 46 5 54 58 62 66 7 74 78 wave length [nm] www.tridonic.com 6