out < +0 meter ch. < +0 ch. < +0 ch. < +7 M nd NSG 0C APPLICATION FOR MIL-STD G CS Test parameter Equipment Standard: MIL-STD G CS Frequency range: to 00 M Curve to : see diagrams Modulation: pulse modulation, 0 % duty cycle erification method: Measuring deviation max. db Test method: Substitution method with db current limitation Monitoring probe: Required for limiting the induced current Signal generation: NSG 0C-0 Modulator: included in NSG 0C-0 meter: x included in NSG 0C-0 amplifier: included in NSG 0C-0 Directional coupler: included in NSG 0C-0 Current injection probe: CIP A Monitoring probe: MD 0A : x PCJ 0B Termination: x 0 Ω 0 W Attenuation: db, db, 0 db, 0 db as shown in table Device control: incl. in NSG 0 user interface Software (optional): icd.control version. or higher WARNING: The power meter inputs are very sensitive. It is the user s responsibility to ensure that the selected test levels does not damage the equipment. Any hardware/setup changes should be calculated before starting the test. Calibration set-up for monitoring probe PCJ 0B NSG 0 NSG 0C-0 meter ch. Remarks: It is recommended to connect the MD 0 remote port with the user port of NSG 0 and select the function MD 0 adaptive probe in the NSG 0 firmware (version. or higher). The monitoring probe MD 0 will be calibrated in passive and active mode automatically. MD 0A + FIX MD0
Test level for MIL STD G CS curve # Test level for MIL STD G CS curve # 0 00 0 77 77 0 0 7 0 0 0,0 0 00 Frequency in M 0 00 0 0 0 8 0 0 0,0 0 00 Frequency in M 8 7 Test level for MIL STD G CS curve # Test level for MIL STD G CS curve # 0 00 0 0 0 8 0 0 0,0 0 00 Frequency in M 8 8 0 00 0 0 0 7 7 0 0 0,0 0 00 Frequency in M 7 8 Test level for MIL STD G CS curve # 0 00 0 0 0 0 0 0 0 0 0,0 0 00 Frequency in M Use of the attenuators on the and on the power meter channel of NSG 0C-0 Test level of MIL-STD-G CS Attenuator in db on CIP A Attenuator in db on power meter of NSG 0C-0 Curve # 0 Curve # 0 Curve # 0 0 Curve # 0 Curve # 0 0 77 dbµa ( to 0 ) 0 0 77 dbµa (0 to M) 0 Table : Use of the attenuators
out < +0 out < +0 out < +0 meter ch. < +0 ch. < +0 ch. < +7 meter ch. < +0 ch. < +0 ch. < +7 meter ch. < +0 ch. < +0 ch. < +7 M M M nd nd nd Calibration set-up for curve # to curve # and 77 dbµa (for 77 dbµa in the range 0 to M) NSG 0 NSG 0C-0 Please use the attenuator with values as given in Table to allow level setting above the amplifier noise. PCJ 0B meter ch. MD 0A + FIX MD0 CIP A Attenuator as required for the test level erification set-up for curve # to curve # and 77 dbµa (for 77 dbµa in the range 0 to M) NSG 0 NSG 0C-0 Please use the same attenuators and the same cables as used for system and probe PCJ 0B meter ch. MD 0A + FIX MD0 CIP A Attenuator as use for system calibration Test set-up for curve # to curve # and 77 dbµa (for 77 dbµa in the range 0 to M) supply unit PSU 00 NSG 0 NSG 0C-0 Please use the same attenuators and the same cables as used for system and probe meter ch. Attenuator as use for system calibration MD 0A CIP A power / signal cable
out < +0 out < +0 out < +0 meter ch. < +0 ch. < +0 ch. < +7 meter ch. < +0 ch. < +0 ch. < +7 meter ch. < +0 ch. < +0 ch. < +7 M M M nd nd nd Calibration set-up for curve # NSG 0 NSG 0C-0 Please use a 0 db attenuator to protect power meter channel. Remove the attenuator on the BCI probe. 0 db Attenuator PCJ 0B meter ch. MD 0A + FIX MD0 CIP A erification set-up for curve # NSG 0 NSG 0C-0 PCJ 0B meter ch. MD 0A + FIX MD0 CIP A Test set-up for curve # NSG 0 NSG 0C-0 supply unit PSU 00 meter ch. MD 0A CIP A power / signal cable
out < +0 out < +0 meter ch. < +0 ch. < +0 ch. < +7 meter ch. < +0 ch. < +0 ch. < +7 M M nd nd Calibration set-up for 77 dbµa in the range to 0 NSG 0 NSG 0C-0 Please remove the 0 db attenuator to protect power meter and the attenuator on the. PCJ 0B meter ch. MD 0A + FIX MD0 CIP A Test set-up for for 77 dbµa in the range to 0 NSG 0 NSG 0C-0 supply unit PSU 00 meter ch. MD 0A CIP A power / signal cable AMETEK CTS Europe GmbH Landsberger Str. Berlin Germany T + 0 88 F + 0 88 info.rf.cts@ametek.com www.ametek-cts.com December 07 Teseq Specifications subject to change without notice. Teseq is an ISO-registered company. Its products are designed and manufactured under the strict quality and environmental requirements of the ISO 00. This document has been carefully checked. However, Teseq does not assume any liability for errors or inaccuracies. 8- E0 MIL-STD G Dec. 07