Energy Storage Elements: Capacitors and Inductors

Similar documents
Energy Storage Elements: Capacitors and Inductors

Boise State University Department of Electrical and Computer Engineering ECE 212L Circuit Analysis and Design Lab

Boise State University Department of Electrical and Computer Engineering ECE 212L Circuit Analysis and Design Lab

Coupling Element and Coupled circuits. Coupled inductor Ideal transformer Controlled sources

EE215 FUNDAMENTALS OF ELECTRICAL ENGINEERING

TUTORIAL PROBLEMS. E.1 KCL, KVL, Power and Energy. Q.1 Determine the current i in the following circuit. All units in VAΩ,,

EE 2006 Electric Circuit Analysis Spring January 23, 2015 Lecture 02

Physics 4B. A positive value is obtained, so the current is counterclockwise around the circuit.

PHYSICS - CLUTCH CH 28: INDUCTION AND INDUCTANCE.

Electrical Circuits 2.1 INTRODUCTION CHAPTER

Electrical Circuits II (ECE233b)

I. INTRODUCTION. There are two other circuit elements that we will use and are special cases of the above elements. They are:

EE 2006 Electric Circuit Analysis Fall September 04, 2014 Lecture 02

ELG 2135 ELECTRONICS I SECOND CHAPTER: OPERATIONAL AMPLIFIERS

matter consists, measured in coulombs (C) 1 C of charge requires electrons Law of conservation of charge: charge cannot be created or

PHYSICS - CLUTCH 1E CH 28: INDUCTION AND INDUCTANCE.

ECE 320 Energy Conversion and Power Electronics Dr. Tim Hogan. Chapter 1: Introduction and Three Phase Power

Chapter 6 Electrical Systems and Electromechanical Systems

Electrical Engineering Department Network Lab.

Linearity. If kx is applied to the element, the output must be ky. kx ky. 2. additivity property. x 1 y 1, x 2 y 2

(b) i(t) for t 0. (c) υ 1 (t) and υ 2 (t) for t 0. Solution: υ 2 (0 ) = I 0 R 1 = = 10 V. υ 1 (0 ) = 0. (Given).

i I (I + i) 3/27/2006 Circuits ( F.Robilliard) 1

6.01: Introduction to EECS 1 Week 6 October 15, 2009

I. INTRODUCTION. 1.1 Circuit Theory Fundamentals

FE REVIEW OPERATIONAL AMPLIFIERS (OP-AMPS)( ) 8/25/2010

Revision: December 13, E Main Suite D Pullman, WA (509) Voice and Fax

( ) = ( ) + ( 0) ) ( )

R. W. Erickson. Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder

CHAPTER 13. Exercises. E13.1 The emitter current is given by the Shockley equation:

COLLEGE OF ENGINEERING PUTRAJAYA CAMPUS FINAL EXAMINATION SPECIAL SEMESTER 2013 / 2014

Introduction to circuit analysis. Classification of Materials

Chapter 10 Sinusoidal Steady-State Power Calculations

Copyright 2004 by Oxford University Press, Inc.

Announcements. Lecture #2

Circuits II EE221. Instructor: Kevin D. Donohue. Instantaneous, Average, RMS, and Apparent Power, and, Maximum Power Transfer, and Power Factors

55:041 Electronic Circuits

Sections begin this week. Cancelled Sections: Th Labs begin this week. Attend your only second lab slot this week.

FEEDBACK AMPLIFIERS. v i or v s v 0

INDUCTANCE. RC Cicuits vs LR Circuits

Transfer Functions. Convenient representation of a linear, dynamic model. A transfer function (TF) relates one input and one output: ( ) system

MAE140 - Linear Circuits - Winter 16 Final, March 16, 2016

6.01: Introduction to EECS I Lecture 7 March 15, 2011

55:041 Electronic Circuits

Physics 1202: Lecture 11 Today s Agenda

55:141 Advanced Circuit Techniques Two-Port Theory

Circuit Variables. Unit: volt (V = J/C)

College of Engineering Department of Electronics and Communication Engineering. Test 1 With Model Answer

Module B3 3.1 Sinusoidal steady-state analysis (single-phase), a review 3.2 Three-phase analysis. Kirtley

EE C245 ME C218 Introduction to MEMS Design

Driving your LED s. LED Driver. The question then is: how do we use this square wave to turn on and turn off the LED?

Lecture #4 Capacitors and Inductors Energy Stored in C and L Equivalent Circuits Thevenin Norton

Week 11: Differential Amplifiers

3.2 Terminal Characteristics of Junction Diodes (pp )

VI. Transistor Amplifiers

ELECTRONICS. EE 42/100 Lecture 4: Resistive Networks and Nodal Analysis. Rev B 1/25/2012 (9:49PM) Prof. Ali M. Niknejad

Chapter 6. Operational Amplifier. inputs can be defined as the average of the sum of the two signals.

Physics Electricity and Magnetism Lecture 12 - Inductance, RL Circuits. Y&F Chapter 30, Sect 1-4

ECE 2100 Circuit Analysis

G = G 1 + G 2 + G 3 G 2 +G 3 G1 G2 G3. Network (a) Network (b) Network (c) Network (d)

The Decibel and its Usage

EMF induced in a coil by moving a bar magnet. Induced EMF: Faraday s Law. Induction and Oscillations. Electromagnetic Induction.

Diode. Current HmAL Voltage HVL Simplified equivalent circuit. V γ. Reverse bias. Forward bias. Designation: Symbol:

), it produces a response (output function g (x)

Physics 114 Exam 2 Fall 2014 Solutions. Name:

Transfer Characteristic

Uncertainty in measurements of power and energy on power networks

ECE 2100 Circuit Analysis

Lecture 5: Operational Amplifiers and Op Amp Circuits

Advanced Circuits Topics - Part 1 by Dr. Colton (Fall 2017)

Complex Numbers, Signals, and Circuits

Chapter 9 Complete Response of Circuits with Two Storage Elements

Electric and magnetic field sensor and integrator equations

College of Engineering Department of Electronics and Communication Engineering. Test 2

Graphical Analysis of a BJT Amplifier

NUMERICAL DIFFERENTIATION

Inductor = (coil of wire)

V V. This calculation is repeated now for each current I.

55:141 Advanced Circuit Techniques Two-Port Theory

Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science Circuits and Electronics Spring 2001

Department of Electrical and Computer Engineering FEEDBACK AMPLIFIERS

5.6 Small-Signal Operation and Models

FE REVIEW OPERATIONAL AMPLIFIERS (OP-AMPS)

Circuit Theorems. Introduction

DC Circuits. Crossing the emf in this direction +ΔV

UNIVERSITY OF UTAH ELECTRICAL & COMPUTER ENGINEERING DEPARTMENT. 10k. 3mH. 10k. Only one current in the branch:

Selected Student Solutions for Chapter 2

Circuit Theory I

Section 8.3 Polar Form of Complex Numbers

MAE140 Linear Circuits (for non-electrical engs)

ECSE Linearity Superposition Principle Superposition Example Dependent Sources. 10 kω. 30 V 5 ma. 6 kω. 2 kω

Lecture 10: Small Signal Device Parameters

Fundamental loop-current method using virtual voltage sources technique for special cases

Physics 5153 Classical Mechanics. Principle of Virtual Work-1

Prof. Paolo Colantonio a.a

Circuit Theory I

Formulation of Circuit Equations

COMPARISON OF SOME RELIABILITY CHARACTERISTICS BETWEEN REDUNDANT SYSTEMS REQUIRING SUPPORTING UNITS FOR THEIR OPERATIONS

A new Approach for Solving Linear Ordinary Differential Equations

Physics 5153 Classical Mechanics. D Alembert s Principle and The Lagrangian-1

Lab 2e Thermal System Response and Effective Heat Transfer Coefficient

Transcription:

CHAPTER 6 Energy Storage Elements: Capactors and Inductors To ths pont n our study of electronc crcuts, tme has not been mportant. The analyss and desgns we hae performed so far hae been statc, and all crcut responses at a gen tme hae depended only on the crcut nputs at that tme. In ths chapter, we shall ntroduce two mportant passe crcut elements: the capactor and the nductor. 6.1. Introducton and A Mathematcal Fact 6.1.1. Capactors and nductors, whch are the electrc and magnetc duals of each other, dffer from resstors n seeral sgnfcant ways. Unlke resstors, whch dsspate energy, capactors and nductors do not dsspate but store energy, whch can be retreed at a later tme. They are called storage elements. Furthermore, ther branch arables do not depend algebracally upon each other. Rather, ther relatons nole temporal derates and ntegrals. Thus, the analyss of crcuts contanng capactors and nductors nole dfferental equatons n tme. 6.1.2. An mportant mathematcal fact: Gen d f(t) = g(t), dt 77

78 6. ENERGY STORAGE ELEMENTS: CAPACITORS AND INDUCTORS 6.2. Capactors 6.2.1. A capactor s a passe element desgned to store energy n ts electrc feld. The word capactor s dered from ths element s capacty to store energy. 6.2.2. When a oltage source (t) s connected across the capactor, the amount of charge stored, represented by q, s drectly proportonal to (t),.e., q(t) = C(t) where C, the constant of proportonalty, s known as the capactance of the capactor. The unt of capactance s the farad (F) n honor of Mchael Faraday. 1 farad = 1 coulomb/olt. 6.2.3. Crcut symbol for capactor of C farads: C C (a) (b) 6.2.4. Snce = dq dt, then the current-oltage relatonshp of the capactor s (6.2) = C d dt. Note that n (6.2), the capactance alue C s constant (tme-narant) and that the current and oltage are both functons of tme (tme-aryng). So, n fact, the full form of (6.2) s (t) = C d dt (t). Hence, the oltage-current relaton s (t) = 1 C t t o (τ)dτ (t o )

6.2. CAPACITORS 79 Slope = C 0 d/dt where (t o ) s the oltage across the capactor at tme t o. Note that capactor oltage depends on the past hstory of the capactor current. Hence, the capactor has memory. 6.2.5. The nstantaneous power delered to the capactor s p(t) = (t) (t) = (C ddt ) (t) (t). The energy stored n the capactor s w(t) = t p(τ)dτ = 1 2 C2 (t). In the aboe calculaton, we assume ( ) = 0, because the capactor was uncharged at t =. 6.2.6. Typcal alues (a) Capactors are commercally aalable n dfferent alues and types. (b) Typcally, capactors hae alues n the pcofarad (pf) to mcrofarad (µf) range. (c) For comparson, two peces of nsulated wre about an nch long, when twsted together, wll hae a capactance of about 1 pf. 6.2.7. Two mportant mplcatons of (6.2): (a) A capactor s an open crcut to dc. When the oltage across a capactor s not changng wth tme (.e., dc oltage), ts derate wrt. tme s d dt = 0 and hence the current through the capactor s (t) = C d dt = C 0 = 0.

80 6. ENERGY STORAGE ELEMENTS: CAPACITORS AND INDUCTORS (b) The oltage across a capactor cannot jump (change abruptly) Because = C d dt, a dscontnuous change n oltage requres an nfnte current, whch s physcally mpossble. t t 6.2.8. Remark: An deal capactor does not dsspate energy. It takes power from the crcut when storng energy n ts feld and returns preously stored energy when delerng power to the crcut. Example 6.2.9. If a 10 µf s connected to a oltage source wth (t) = 50 sn 2000t determne the current through the capactor. V Example 6.2.10. Determne the oltage across a 2-µF capactor f the current through t s (t) = 6e 3000t ma Assume that the ntal capactor oltage (at tme t = 0) s zero.

6.2. CAPACITORS 81 Example 6.2.11. Obtan the energy stored n each capactor n the fgure below under dc condtons. 2 mf 2 kω 5 kω 6 ma 3 kω 4 kω 4 mf

82 6. ENERGY STORAGE ELEMENTS: CAPACITORS AND INDUCTORS 6.3. Seres and Parallel Capactors We know from resste crcuts that seres-parallel combnaton s a powerful tool for smplfyng crcuts. Ths technque can be extended to seres-parallel connectons of capactors, whch are sometmes encountered. We desre to replace these capactors by a sngle equalent capactor C eq. 6.3.1. The equalent capactance of N parallel-connected capactors s the sum of the nddual capactance. C eq = C 1 C 2 C N 1 2 3 N C 1 C2 C3 CN The equalent capactance of N seres-connected capactors s the the recprocal of the sum of the recprocals of the nddual capactances. 1 = 1 1 1 C eq C 1 C 2 C N C 1 C 2 C 3 C N 1 2 3 N Example 6.3.2. Fnd the C eq. 5 µf 60 µf a 20 µf 6 µf 20 µf C eq b

6.4. INDUCTORS 83 6.4. Inductors 6.4.1. An nductor s a passe element desgned to store energy n ts magnetc feld. 6.4.2. Inductors fnd numerous applcatons n electronc and power systems. They are used n power supples, transformers, rados, TVs, radars, and electrc motors. 6.4.3. Crcut symbol of nductor: L L L 6.4.4. If a current s allowed to pass through an nductor, the oltage across the nductor s drectly proportonal to the tme rate of change of the current,.e., (6.3) (t) = L d dt (t), where L s the constant of proportonalty called the nductance of the nductor. The unt of nductance s henry (H), named n honor of Joseph Henry. 1 henry equals 1 olt-second per ampere. 6.4.5. By ntegraton, the current-oltage relaton s (t) = 1 L t where (t o ) s the current at tme t o. t o (τ) dτ (t o ), 6.4.6. The nstantaneous power delered to the nductor s p(t) = (t) (t) = (L ddt ) (t) (t)

84 6. ENERGY STORAGE ELEMENTS: CAPACITORS AND INDUCTORS Slope = L The energy stored n the nductor s 0 d/dt w(t) = t p(τ) dτ = 1 2 L2 (t). 6.4.7. Lke capactors, commercally aalable nductors come n dfferent alues and types. Typcal practcal nductors hae nductance alues rangng from a few mcrohenrys (µh), as n communcaton systems, to tens of henrys (H) as n power systems. 6.4.8. Two mportant mplcatons of (6.3): (a) An nductor acts lke a short crcut to dc. When the current through an nductor s not changng wth tme (.e., dc current), ts derate wrt. tme s d dt = 0 and hence the oltage across the nductor s (t) = L d dt = L 0 = 0. (b) The current through an nductor cannot change nstantaneously. Ths opposton to the change n current s an mportant property of the nductor. A dscontnuous change n the current through an nductor requres an nfnte oltage, whch s not physcally possble. (a) t 6.4.9. Remark: The deal nductor does not dsspate energy. The energy stored n t can be retreed at a later tme. The nductor takes (b) t

6.4. INDUCTORS 85 power from the crcut when storng energy and delers power to the crcut when returnng preously stored energy. Example 6.4.10. If the current through a 1-mH nductor s (t) = 20 cos 100t ma, fnd the termnal oltage and the energy stored. Example 6.4.11. Fnd the current through a 5-H nductor f the oltage across t s { 30t 2, t > 0 (t) = 0, t < 0. In addton, fnd the energy stored wthn 0 < t < 5 s.

86 6. ENERGY STORAGE ELEMENTS: CAPACITORS AND INDUCTORS Example 6.4.12. The termnal oltage of a 2-H nductor s (t) = 10(1 t) V. Fnd the current flowng through t at t = 4 s and the energy stored n t wthn 0 < t < 4 s. Assume (0) = 2 A. Example 6.4.13. Determne C, L and the energy stored n the capactor and nductor n the followng crcut under dc condtons. 1 Ω 5 Ω L 4 Ω 12 V 2 H C 1 F

6.5. SERIES AND PARALLEL INDUCTORS 87 Example 6.4.14. Determne C, L and the energy stored n the capactor and nductor n the followng crcut under dc condtons. L 6 H 4 A 6 Ω 2 Ω C 4 F 6.5. Seres and Parallel Inductors 6.5.1. The equalent nductance of N seres-connected nductors s the sum of the nddual nductances,.e., L eq = L 1 L 2 L N L 2 L 3 L N L 1 1 2 3 N

88 6. ENERGY STORAGE ELEMENTS: CAPACITORS AND INDUCTORS 6.5.2. The equalent nductance of N parallel nductors s the recprocal of the sum of the recprocals of the nddual nductances,.e., 1 = 1 1 1 L eq L 1 L 2 L N 2008 11:59 AM Page 232 1 2 3 N L 1 L 2 L 3 L N 6.5.3. Remark: Note that (a) nductors n seres are combned n exactly the same way as resstors n seres and (b) nductors Chapter 6 Capactors n parallel and Inductors are combned n the same way as resstors n parallel. TABLE 6.1 Important characterstcs of the basc elements. Relaton Resstor (R) Capactor (C) Inductor (L) -: -: p or w: R R p 2 R 2 R 1 C t dt (t 0 ) t 0 d C dt w 1 2 C2 Seres: C eq C 1C 2 R eq R 1 R 2 L eq L 1 L 2 C 1 C 2 Parallel: L eq L 1L 2 R eq R 1R 2 C eq C 1 C 2 R 1 R 2 L 1 L 2 At dc: Same Open crcut Short crcut Crcut arable that cannot change abruptly: Not applcable d L dt 1 L t w 1 2 L2 t 0 dt (t 0 ) Passe sgn conenton s assumed. It s approprate at ths pont to summarze the most mportant characterstcs of the three basc crcut elements we hae studed. The summary s gen n Table 6.1. The wye-delta transformaton dscussed n Secton 2.7 for resstors can be extended to capactors and nductors.

6.6. APPLICATIONS: INTEGRATORS AND DIFFERENTIATORS 89 Example 6.5.4. Fnd the equalent nductance L eq of the crcut shown below. 4 H 20 H a L eq 7 H 12 H 8 H 10 H b 6.6. Applcatons: Integrators and Dfferentators 6.6.1. Capactors and nductors possess the followng three specal propertes that make them ery useful n electrc crcuts: (a) The capacty to store energy makes them useful as temporary oltage or current sources. Thus, they can be used for generatng a large amount of current or oltage for a short perod of tme. (b) Capactors oppose any abrupt change n oltage, whle nductors oppose any abrupt change n current. Ths property makes nductors useful for spark or arc suppresson and for conertng pulsatng dc oltage nto relately smooth dc oltage. (c) Capactors and nductors are frequency senste. Ths property makes them useful for frequency dscrmnaton. The frst two propertes are put to use n dc crcuts, whle the thrd one s taken adantage of n ac crcuts. In ths fnal part of the chapter, we wll consder two applcatons nolng capactors and op amps: ntegrator and dfferentator.

90 6. ENERGY STORAGE ELEMENTS: CAPACITORS AND INDUCTORS 6.6.2. An ntegrator s an op amp crcut whose output s proportonal to the ntegral of the nput sgnal. We obtan an ntegrator by replacng the feedback resstor R f n the nertng amplfer by a capactor. C C R R a 0 Ths ges whch mples d dt o(t) = 1 RC (t), t o (t) = 1 (τ)dτ o (0). RC 0 To ensure that o (0) = 0, t s always necessary to dscharge the ntegrators capactor pror to the applcaton of a sgnal. In practce, the op amp ntegrator requres a feedback resstor to reduce dc gan and preent saturaton. Care must be taken that the op amp operates wthn the lnear range so that t does not saturate.

6.6. APPLICATIONS: INTEGRATORS AND DIFFERENTIATORS 91 6.6.3. A dfferentator s an op amp crcut whose output s proportonal to the dfferentaton of the nput sgnal. We obtan a dfferentator by replacng the nput resstor n the nertng amplfer by a capactor. Ths ges R R C C a 0 o (t) = RC d dt (t). Dfferentator crcuts are electroncally unstable because any electrcal nose wthn the crcut s exaggerated by the dfferentator. For ths reason, the dfferentator crcut aboe s not as useful and popular as the ntegrator. It s seldom used n practce.