Return fi lters FRI series Maximum pressure up to 0 bar - Flow rate up to 500 l/min 9 Return fi lters
FILTER SIZING The correct filter sizing have to be based on the variable pressure drop depending by the application. For example, for the return filter the pressure drop have to be in the range 0. - 0.6 bar. The pressure drop calculation is performed by adding together the value of the housing with the value of the filter. The pressure drop in the housing is proportional to the fluid density (kg/dm ); all the graphs in the catalogue are referred to mineral oil with density of 0.86 kg/dm. The filter pressure drop is proportional to its viscosity (mm /s), the corrective factor Y is related to an oil viscosity different than 0 mm /s. Sizing data for single cartridge, head at top pc = housing pressure drop [bar] pe = pressure drop [bar] Y = Multiplication factor Y (see correspondent table), depending on the filter size, on the filter lenght and on the filter media Q = flow rate (l/min) V reference viscosity = 0 mm /s (cst) V = operating viscosity in mm /s (cst) pe = Y : 000 x Q x (V/V) p Tot. = pc + pe Calculation examples with HLP Mineral oil Variation in viscosity Application data: Top tank return filter with in-line connections Pressure Pmax = 0 bar Flow rate Q = 0 l/min Viscosity V = 6 mm /s (cst) Oil viscosity = 0.86 kg/dm Required filtration efficiency = 5 μm with absolute filtration With bypass valve and / inlet connection From the working pressure and the flow rate we understand it should be possible using the following top tank return filter series: MPT, MPH and FRI. Let s proceed with MPT series. The size 0 doesn t achieve the required flow rate, therefore we have to consider the size 00. The final version of size 00 (0, 0, 0, 0 and ) will be then defined in function of the mounting characteristics. pc = 0.0 bar ( see graphic below, considering size 00 with the max available lenght * to get the lowest pressure drop) pe = (.0 : 000) x 0 x (6/0) = 0.7 bar p Tot. = 0.0 + 0.7 = 0. bar The selection is correct because the total pressure drop value is inside the admissible range for top tank return filters. It is of course possible trying to find a different solution, according to the mounting position or to other commercial need, repeating the previous steps while using a different series or lenght. Δp bar MPT 0 - Length - 0.0 0.0 0.0 0.0 0 * G / 0 60 0 80 0 00 Flow rate l/min housings p pressure drop. The curves are plotted using mineral oil with density of 0.86 kg/dm in compliance with ISO 968. p varies proportionally with density. Corrective factor Corrective factor Y, to be used for the filter pressure drop calculation. The values depend to the filter size and lenght and to the filter media. Reference viscosity 0 mm /s Return filters Type MF 00 MF 00 MFX 00 MF 00 MFX 00 MF 80 MFX 80 MF 90 MFX 90 MF 00 MFX 00 MF 750 MFX 750 CU 05 CU 00 CU 00 CU 50 CU 60 CU 850 MR 00 MR 50 MR 60 MR 850 5 5 A0 7.00 9.0.00 7.00 8.0 7. 0.5 6.0.67.69.69.0.00.90.08 78.00 5.88 5.0.5.96.06 9.00.70 7.80 5.50.0 5.5.00.60.8.0.06.8.0 0.7 0.60 0.7 0.7 0. Absolute filtration Nominal filtration H Series N Series A06 A0 A6 A5 P0 P5 M5 M60 M90 50.08 0.00 6.00 9.00 6. 5.5.0. 8.00 7. 5.00..85.00 9.00 6.56 5...68..0 50.08.0.50 9.00 5.0.05.7.7.75.87.60 0.8 8.00 0.88.5.55.68 0.8 7.00 0.80 6.87.97.8.85.8.0.56.8.9.0.0 0.65 0. 0.6 0.8 0.6 0.00 8.67 6.86.65.0.6 0.68 0.60.9 0.88 0.6 0.9 8.00 0. 5..55 0.85 0. 6.90.0.70.60.6...08 0.68. 0.8 0.60 0.8 0.0 0. 0. 0.7 0. 6.00 8.7 5.70..0.56 0.5 0.9. 0.85 0.5 0.6.00 0.00.95.5 0.7 0. 6.0.0.0.0.5.9.0.00 0.56. 0.76 0.56 0.0 0.8 0.5 0. 0.7 0. 9.00 6.88.00.50.00. 0.5 0..06 0.55 0.9 0.6 9..78.00 0.7 0. 0.7.60.00.70.8.90.50.07 0.86 0. 0.9 0.8 0.6 0.5 0. 0. 0. 0.05 0.0 6..6.05.6.9.8 0. 0.5 0.96 0.9 0.9 0. 9..78.00 0.7 0. 0.7.9.9..7.60.8 0.96 0.77 0.7 0.8 0. 0. 0. 0.0 0. 0.08 0.0 0.0 5.5.96.7. 0.96.06 0.9 0. 0.87 0.5 0.5 0.9 8.5.0 0.7 0.59 0.6 0..5.5.8.7.7.0 0.8 0.6 0. 0.7 0.7 0.7 0.6 0.08 0.09 0.07 0.0 0.0.0.5.0 0.96 0.8 0.6 0. 0. 0. 0. 0. 0.06.5.5.0 0.5 0.09 0.0.60.7... 0.5 0. 0. 0. 0.09 0.08 0.08 0.08 0.0 0.0 0.0 0.0 0.0 Introduction 0
Corrective factor Corrective factor Y, to be used for the filter pressure drop calculation. The values depend to the filter size and lenght and to the filter media. Reference viscosity 0 mm /s Suction filters Type SF 50 Nominal filtration N Series P0 P5 65 Low & Medium pressure filters Type CU 0 A0 6.5.6 8.57 5.76 FILTER SIZING Absolute filtration Nominal filtration N-W Series N Series A06 A0 A6 A5 P0 P5 M5 5.6 0. 7.95.05 8.75 6. 5.07.80 8. 6.0.07.6 5.87.5.0..86.60. 0.9.65.9.5 0.85 0. 0. 0. 0.05 Return / Suction filters Type RSX 6 A0 5.. Absolute filtration A6..87 A5.85. CU 0 DN 06 05 00 5.0..0 7.95 5.00..80.95.70 7.0.5.66.00. 0.9.00.89..66.09 0.8.9.57 0.98. 0.70 0.5.98.5 0.6 0.56 0. 0. 0.8 0.5 0.8 0. 0.5 0. 0.65 0. 0. 0. 0.09 0.05 0.8 0. 0.08 RSX 65.06. 0.9.75.05 0.86.6 0.96 0.6 CU 00 5 6..5.60.00 0.8.55.70.8 0.8 0.58.6 0.9 0.7 0.7 0.0. 0.78 0.6 0. 0.7 0.78 0.50 0.0 0.0 0.7 0.75 0.0 0. 0. 0. 0.6 0. 0.7 0.9 0.8 0.9 0.0 0.08 0.06 0.05 CU 900 0.86 0.6 0. 0.0 0. - - 0.05 CU 950.0 0. 0.80 0.0 0.59 0.7 0.0 0.8 0.6 0.5 - - - - 0.05 0.0 MR 60 7 0.88 0.78 0.6 0. 0.6 0. 0.96 0.7 Introduction
FILTER SIZING Corrective factor Corrective factor Y, to be used for the filter pressure drop calculation. The values depend to the filter size and lenght and to the filter media. Reference viscosity 0 mm /s High pressure filters Type HP 0 A0.7 0.8. 77.76 Absolute filtration N - R Series A06 A0 A6 50.07 65.56 9.68 58.5 8. 7.08.8 8.7 5.6 59..08.67 A5 8.6 7.05 0.7 6.7 Nominal filtration N Series M5 - - - - Stainless steel high pressure filters Type HP 0 A0.7 0.8. 77.76 Absolute filtration N Series A06 A0 A6 50.07 65.56 9.68 58.5 8. 7.08.8 8.7 5.6 59..08.67 A5 8.6 7.05 0.7 6.7 HP 09 70.66 6.57 6.57 5.0.8.7 5.77 8.00.6 0.57.8 8.80.67 8.00 5.58.90.90.0 HP 09 70.66 6.57 6.57 5.0.8.7 5.77 8.00.6 0.57.8 0.88.67 8.00 5.58 HP 050 5.75.5 7.7. 7.00 0.0.6 6.5 0.75 6.56.6.70 8.90 6.0.60. 9.09 7.8 5.75.0 7.9.90.6.08.5.60.0.5.07 0.80 HP 050 5.75.5 7.7. 7.00 0.0.6 6.5 0.75 6.56.6.70 8.90 6.0.60. 9.09 7.8 5.75.0 7.9.90.6.08.5 HP 065 58.50.60 0.50.6 5.6 5.88.6 6. 8.8 9.66.88 6.8 0.7 7..9.8. 0.58 HP 5 0.. 6.8 8.80 0.6 6. 9.7 6.60.8 8.66 6.8.6.78.. HP 5 HP 0 0.. 6.8 0.88.0.75. 8.80 0.6 6. 9.7.8..77 9.7 6.60.8 5.0.75.05 0.98 8.66 6.8.6.7.8 0.87 0.78.78...5 0.88 0.77 0.55.78..0.0 0.7 0.6 0.7 Type HP 0 A0.58 8.06 0. 09.9 Absolute filtration H - U Series A06 A0 A6 9.7.5 97.50 8.5 5.7 9.5.6 6.79 9. 75.5.8 9.7 A5 6.78 7.6.8 8.0 HP 500 5..7..8..67.77.98..5.0.78. 0.9 0.77.0.68.09 0.86 0.68.65. 0.75 0.68 0.8 0.5 0.0 0.08 0.05 0.0 HP 09 70.66 6.57 6.57 5.0.8.7 5.77 8.00.6 0.57.8 8.80.67 8.00 5.58 Type A0 Absolute filtration N Series A06 A0 A6 A5 Nominal filtration N Series M5 HP 050 5 7. 9.0 0.85.55 9.86.5 5.95 9.50.90 9..50.0 0.68 7. 6.0 0.50 0.90 8.6 6.90.80.7 5.88.6.69.50 HF 0.65.0.8.95.7..80.6..80.5. 0.90 0.85 0.80 0.8 0.6 0.5 HP 5 9.6.8 8.96 5..0 7.6.00 7.86.89.7 7.60.6 5.9..07 Introduction
Selection Software FILTER SIZING Step Select FILTERS Step Choose fi lter group (Return, Pressure, etc.) Step Choose fi lter type (MPF, MPT, etc.) in function of the max working pressure and the max fl ow rate Step Push PROCEED Step 5 Insert all application data to calculate the fi lter size following the sequence: - working pressure - working fl ow rate - working pressure drop - working temperature - fl uid material and fl uid type - fi ltration media - connection type Step 6 Push CALCULATE to have result; in case of any mistake, the system will advice which parameter is out of range to allow to modify/adjust the selection Step 7 Download PDF Datasheet Report.aspx pushing the button Drawing Introduction
THE NEW FILTER CONCEPT MPFX MPTX MFBX MFX series NEW FILTER ELEMENT WITH EXCLUSIVE INTERFACE CONNECTION Protects the machine from improper use of non-original products. Safety of constant quality protection & reliability With exclusive fi lter you are sure that only fi lter s MP Filtri can be used, ensuring the best cleaning level of the oil due to the use of originals fi lter s. featuring our UNIQUE end cap with polygonal design. UNIQUE polygonal spigot fi tting within the fi lter bowl. The products identified as MPFX, MPTX, MFBX and MFX are protected by one or more of the following patent applications: European Patent Pending: n 6875.9 Italian Patent Pending: n 005000007 US Patent Pending: n 5/,7 Canadian Patent Pending: n,97,58 Return fi lters 58
Return fi lters FRI series Maximum pressure up to 0 bar - Flow rate up to 500 l/min 9 Return fi lters
FRI GENERAL INFORMATION Technical data Return filter Maximum pressure up to 0 bar - Flow rate up to 500 l/min housing materials - body: Aluminium: FRI 55 Anodized Aluminium: FRI 05-00-00-50-60 Phosphated Steel: FRI 850 - Cover: Polyamide, GF reinforced (only for: FRI 55) Anodized Aluminium (the other insert assemblies) - Valve: Polyamide, GF reinforced - Steel Seals - Standard NBR series A - Optional FPM series V Temperature From -5 C to +0 C Note FRI filters are provided for vertical mounting Pressure Working pressure: MPa (0 bar) Bypass valve Opening pressure 0 kpa (. bar) p type - Microfibre filter s - series N: 0 bar - Fluid flow through the filter from OUT to IN. Weights [kg] and volumes [dm ] FRI 05 FRI 00 FRI 00 FRI 50 FRI 55 FRI 60 FRI 850 Weights [kg] Lenght.0.0.8 6...8 8.0 Volumes [dm ] Lenght 0.8 0.70.09.60.0 7.05.50 Hydraulic symbols Style connections + Diff. indic. FRI 55-850 Style connections + Diff. indic FRI 05-00-00-50-60 Return filters 9
GENERAL INFORMATION FRI Pressure drop The curves are plotted using mineral oil with density of 0.86 kg/dm in compliance with ISO 968. p varies proportionally with density. Δp bar 0.6 0. 0. FRI 05-00 - 00 / / Δp bar 0.6 0. 0. FRI 50-55 - 60 / / housings p pressure drop 0 0 50 00 50 00 50 Flow rate l/min 0 0 00 00 600 800 000 Flow rate l/min 0.6 FRI 850 Δp bar 0. 0. / 0 0 500 000 500 000 500 Flow rate l/min 6 FRI 05 6 FRI 00-00 Bypass valve pressure drop Δp bar Δp bar 0 0 8 6 5 75 90 Flow rate l/min 0 0 0 60 90 0 50 Flow rate l/min 6 FRI 50-55 6 FRI 60-850 Δp bar Δp bar 0 0 60 0 80 50 00 Flow rate l/min 0 0 00 800 00 600 000 Flow rate l/min 95 Return filters
FRI Designation & Ordering code FRI05 - FRI00 Series and size FRI05 FRI00 COMPLETE FILTER Configuration example : FRI05 B A G A5 N P0 Configuration example : FRI00 S W G M5 N P0 Bypass valve B With bypass S Without bypass Seals and treatments A V NBR FPM W NBR head anodized Z FPM head anodized filter compatible with fluids HFA-HFB-HFC Filtration rating Axx Mxx Pxx Connections for FRI05 Connections for FRI00 G G/ G/ G / NPT / NPT G SAE 8 - / - 6 UNF SAE - /6 - UN Filtration rating (filter media) A0 Inorganic microfiber µm M5 Wire mesh 5 µm A06 Inorganic microfiber 6 µm M60 Wire mesh 60 µm A0 Inorganic microfiber 0 µm M90 Wire mesh 90 µm A6 Inorganic microfiber 6 µm P0 Resin impregnated paper 0 µm A5 Inorganic microfiber 5 µm P5 Resin impregnated paper 5 µm Element p N 0 bar Execution P0 MP Filtri standard Pxx Customized Element series and size CU05 CU00 FILTER ELEMENT Configuration example : Configuration example : CU05 CU00 A5 M5 N W P0 P0 Filtration rating (filter media) A0 Inorganic microfiber µm M5 Wire mesh 5 µm A06 Inorganic microfiber 6 µm M60 Wire mesh 60 µm A0 Inorganic microfiber 0 µm M90 Wire mesh 90 µm A6 Inorganic microfiber 6 µm P0 Resin impregnated paper 0 µm A5 Inorganic microfiber 5 µm P5 Resin impregnated paper 5 µm Seals and treatments N NBR V FPM W NBR Z FPM filter compatible with fluids HFA-HFB-HFC Filtration rating Axx Mxx Pxx Execution P0 MP Filtri standard Pxx Customized ACCESSORIES Indicators page page DEA DEM DLA Electrical differential indicator Electrical differential indicator Electrical / visual differential indicator 8 8-9 9-0 DTA DVA DVM Electronic differential indicator Visual differential indicator Visual differential indicator DLE Electrical / visual differential indicator 0 Additional features page T Plug Return filters 96
FRI05 - FRI00 FRI Dimensions FRI05 FRI00 97 Return filters
FRI Designation & Ordering code FRI00 - FRI50 - FRI60 Series and size FRI00 FRI50 FRI60 Bypass valve B With bypass S Without bypass Seals and treatments A V NBR FPM W NBR head anodized Z FPM head anodized filter compatible with fluids HFA-HFB-HFC Filtration rating Axx Mxx Pxx COMPLETE FILTER Configuration example : FRI00 B A G A5 N P0 Configuration example : FRI60 S W F M5 N P0 Connections for FRI00 Connections for FRI50 Connections for FRI60 G G G / G / G NPT / NPT / NPT G SAE 6-5/6 - UN SAE - 7/8 - UN SAE - / - UN F SAE 000 psi/m / SAE 000 psi/m / SAE 000 psi/m F SAE 000 psi/unc / SAE 000 psi/unc / SAE 000 psi/unc Filtration rating (filter media) A0 Inorganic microfiber µm M5 Wire mesh 5 µm A06 Inorganic microfiber 6 µm M60 Wire mesh 60 µm A0 Inorganic microfiber 0 µm M90 Wire mesh 90 µm A6 Inorganic microfiber 6 µm P0 Resin impregnated paper 0 µm A5 Inorganic microfiber 5 µm P5 Resin impregnated paper 5 µm Element p N 0 bar Execution P0 MP Filtri standard Pxx Customized Element series and size CU00 CU50 CU60 FILTER ELEMENT Configuration example : Configuration example : CU00 CU60 A5 M5 N W P0 P0 Filtration rating (filter media) A0 Inorganic microfiber µm M5 Wire mesh 5 µm A06 Inorganic microfiber 6 µm M60 Wire mesh 60 µm A0 Inorganic microfiber 0 µm M90 Wire mesh 90 µm A6 Inorganic microfiber 6 µm P0 Resin impregnated paper 0 µm A5 Inorganic microfiber 5 µm P5 Resin impregnated paper 5 µm Seals and treatments N NBR V FPM W NBR Z FPM filter compatible with fluids HFA-HFB-HFC Filtration rating Axx Mxx Pxx Execution P0 MP Filtri standard Pxx Customized ACCESSORIES Indicators page page DEA Electrical differential indicator 8 DTA Electronic differential indicator DEM Electrical differential indicator 8-9 DVA Visual differential indicator DLA Electrical / visual differential indicator 9-0 DVM Visual differential indicator DLE Electrical / visual differential indicator 0 Additional features page T Plug Return filters 98
FRI00 - FRI50 - FRI60 FRI Dimensions FRI00 Threaded connections G FRI00 Flange connections F 99 Return filters
FRI Dimensions FRI00 - FRI50 - FRI60 clearance space for clearance maintenance space FRI50 Threaded connections G immersed in the tank FRI50 Flange connections F Return filters 00
FRI00 - FRI50 - FRI60 clearance space for clearance maintenance space FRI Dimensions FRI60 Threaded connections G immersed in the tank FRI60 Flange connections F 0 Return filters
FRI Designation & Ordering code Series and size FRI55 FRI850 FRI55 - FRI850 Bypass valve B With bypass S Without bypass Filtration rating Seals and treatments Axx Mxx Pxx A NBR V FPM W NBR head anodized filter compatible Z FPM head anodized with fluids HFA-HFB-HFC Connections for FRI55 Connections for FRI850 G G / F / SAE 000 psi/m G / NPT F / SAE 000 psi/unc G SAE - 7/8 - UN G G / G5 / NPT G6 SAE 0-5/8 - UN F / SAE 000 psi/m F / SAE 000 psi/unc Filtration rating (filter media) A0 Inorganic microfiber µm M5 Wire mesh 5 µm A06 Inorganic microfiber 6 µm M60 Wire mesh 60 µm A0 Inorganic microfiber 0 µm M90 Wire mesh 90 µm A6 Inorganic microfiber 6 µm P0 Resin impregnated paper 0 µm A5 Inorganic microfiber 5 µm P5 Resin impregnated paper 5 µm COMPLETE FILTER Configuration example : FRI55 S W F M5 N P0 Configuration example : FRI850 B A G A5 N P0 Element p N 0 bar Execution P0 MP Filtri standard Pxx Customized Element series and size CU50 CU850 Filtration rating (filter media) A0 Inorganic microfiber µm M5 Wire mesh 5 µm A06 Inorganic microfiber 6 µm M60 Wire mesh 60 µm A0 Inorganic microfiber 0 µm M90 Wire mesh 90 µm A6 Inorganic microfiber 6 µm P0 Resin impregnated paper 0 µm A5 Inorganic microfiber 5 µm P5 Resin impregnated paper 5 µm Seals and treatments N NBR V FPM W NBR Z FPM filter compatible with fluids HFA-HFB-HFC Filtration rating Axx Mxx Pxx FILTER ELEMENT Configuration example : CU50 M5 W P0 Configuration example : CU850 A5 N P0 Execution P0 MP Filtri standard Pxx Customized FRI55 ACCESSORIES Indicators page page BVA Axial pressure gauge 8 BEA Electrical pressure indicator BVR Radial pressure gauge 8-9 BEM Electrical pressure indicator BVP Visual pressure indicator with automatic reset 9-0 BLA Electrical / visual pressure indicator BVQ Visual pressure indicator with manual reset 0 FRI850 ACCESSORIES Indicators page page DEA Electrical differential indicator 8 DTA Electronic differential indicator DEM Electrical differential indicator 8-9 DVA Visual differential indicator DLA Electrical / visual differential indicator 9-0 DVM Visual differential indicator DLE Electrical / visual differential indicator 0 Additional features page T Plug Return filters 0
FRI55 - FRI850 FRI Dimensions FRI55 FRI850 0 Return filters
FRI SPARE PARTS Order number for spare parts FRI 05-00 a c d b e Item: series FRI 05 FRI 00 Q.ty: pc. See order table Q.ty: pc. (a e) Seal Kit code number NBR FPM 0050 00500 0050 0050 FRI 00-50 - 60 a a c c d d f b b e Item: series FRI 00 FRI 50 FRI 60 Q.ty: pc. See order table Q.ty: pc. (a f) Seal Kit code number NBR FPM 00505 0050 00506 0050 00507 0050 Return fi lters 0
SPARE PARTS FRI Order number for spare parts FRI 55 c a d b Q.ty: pc. Q.ty: pc. Q.ty: pc. Item: (a d) Seal Kit code number Contamination series NBR FPM retainer binder FRI 55 See order table 00500 00500 00600 FRI 850 a c d e b Item: Q.ty: pc. Q.ty: pc. (a e) Seal Kit code number series NBR FPM FRI 850 See order table 00508 00505 05 Return fi lters