F ballasts E PCA EXCE oneall lp Y II, 1 80 W EXCE Product description Processor-controlled ballast with y II inside Highest possible energy class CEMA EEI = A1 BAT 1 oise-free precise control via I or DSI signal, switchdim or corridorfuctio ominal life up to 0,000 h (at ta 50 C with a failure rate max. 0. % per 1,000 h) Multi-lamp management OEM-specific reserved memory areas Extended I commands 5-year guarantee Interfaces I DSI switchdim (with memory function + selectable dimming rate) corridorfuctio ( preprogrammed profiles + individually programmable) Integrated SMART interface for function with all SMART Sensors and SMART plugs of the y II range Ø,1 side fixing feature D 1,1 0 Functions Intelligent Temperature Guard (overtemperature protection) Intelligent Voltage Guard (overvoltage indication and undervoltage shutdown) Optimum filament heating in any dimmer setting Disconnection of filament heating from a dimming level of approx. 90 % for maximum energy efficiency (SMART-Heating concept) Fade rates between 0 ms and 90 s (min. max.) corridorfuctio with ambient light control Automatically triggered emergency lighting value in DC mode %, can be set between 1 and 0 % For emergency lighting systems as per E 501 Automatic start after replacement of defective lamps Automatic shutdown if the lamp is faulty Dimming possible in DC mode È Standards, page Wiring diagrams and installation examples, page 8 Technical data Mains voltage range AC voltage range DC voltage range Mains frequency Overvoltage protection Typ. power input on standby Protective hot restart 0 0 V 198 V 1 80 V (lamp start 198 V DC) 0 / 50 / 0 Hz 0 V AC, 1 h < 0. W Dimming range 1 0 % amp start possible from 1 % Operating frequency Type of protection Ordering data Type For luminaires with 1 lamp 0.5 s for AC / 0. s for DC ~ 0 khz IP0 Article number Packaging, carton Packaging, pallet Weight per pc. PCA 1x1/ EXCE oneall lp Y II 185 pc(s). 0 pc(s). 0. kg PCA 1x1/9 EXCE oneall lp Y II 1851 pc(s). 0 pc(s). 0.9 kg PCA 1x8/5 EXCE oneall lp Y II 1858 pc(s). 0 pc(s). 0. kg PCA 1x5/9/80 EXCE oneall lp Y II 1855 pc(s). 0 pc(s). 0. kg For luminaires with lamps PCA x1/ EXCE oneall lp Y II 185 pc(s). 0 pc(s). 0. kg PCA x1/9 EXCE oneall lp Y II 185111 pc(s). 0 pc(s). 0. kg PCA x8/5 EXCE oneall lp Y II 1859 pc(s). 0 pc(s). 0.5 kg PCA x5/9 EXCE oneall lp Y II 185 pc(s). 0 pc(s). 0.58 kg PCA x80 EXCE oneall lp Y II 185 pc(s). 0 pc(s). 0.8 kg Data sheet 0/1-FD00-9 www.tridonic.com 1
F ballasts Specific technical data amp wattage amp type Type For luminaires with 1 lamp Article number Dimensions x W x H Hole spacing D amp power Circuit power EEI Current at λ at 50 Hz 0 V 50 Hz 0 V tc point max. Ambient temperature ta 1 x 1 W PCA 1x1/ EXCE oneall lp Y II 185 0 x 0 x 1 mm 50 mm 1 W 1.0 W A1 BAT 0.08 A 0.95 80 C -5... 0 C 1 x W PCA 1x1/ EXCE oneall lp Y II 185 0 x 0 x 1 mm 50 mm W 5.5 W A1 BAT 0.1 A 0.9 80 C -5... 0 C 1 x 1 W PCA 1x1/9 EXCE oneall lp Y II 1851 0 x 0 x 1 mm 50 mm 1 W.0 W A1 BAT 0.11 A 0.95 80 C -5... 0 C 1 x W PCA 1x1/9 EXCE oneall lp Y II 1851 0 x 0 x 1 mm 50 mm W 5.5 W A1 BAT 0.1 A 0.9 80 C -5... 5 C 1 x 9 W PCA 1x1/9 EXCE oneall lp Y II 1851 0 x 0 x 1 mm 50 mm 8 W 1.5 W A1 BAT 0.19 A 0.9 80 C -5... 5 C 1 x 0 W PCA 1x1/9 EXCE oneall lp Y II 1851 0 x 0 x 1 mm 50 mm 0 W.0 W A1 BAT 0.0 A 0.98 80 C -5... 5 C 1 x 8 W PCA 1x8/5 EXCE oneall lp Y II 1858 0 x 0 x 1 mm 50 mm 8 W 0.5 W A1 BAT 0.1 A 0.95 80 C -5... 5 C 1 x 5 W PCA 1x8/5 EXCE oneall lp Y II 1858 0 x 0 x 1 mm 50 mm 5 W 58.0 W A1 BAT 0. A 0.98 80 C -5... 0 C 1 x 5 W PCA 1x5/9/80 EXCE oneall lp Y II 1855 0 x 0 x 1 mm 50 mm 5 W 9.0 W A1 BAT 0.18 A 0.95 85 C -5... 5 C 1 x 9 W PCA 1x5/9/80 EXCE oneall lp Y II 1855 0 x 0 x 1 mm 50 mm 9 W 5.0 W A1 BAT 0.5 A 0.9 80 C -5... 0 C 1 x 55 W PCA 1x5/9/80 EXCE oneall lp Y II 1855 0 x 0 x 1 mm 50 mm 55 W 0.0 W A1 BAT 0.8 A 0.9 80 C -5... 0 C 1 x 80 W PCA 1x5/9/80 EXCE oneall lp Y II 1855 0 x 0 x 1 mm 50 mm 80 W 85.5 W A1 BAT 0.0 A 0.99 80 C -5... 0 C 1 x 80 W PCA 1x5/9/80 EXCE oneall lp Y II 1855 0 x 0 x 1 mm 50 mm 80 W 85.5 W A1 BAT 0. A 0.98 80 C -5... 0 C For luminaires with lamps x 1 W PCA x1/ EXCE oneall lp Y II 185 0 x 0 x 1 mm 50 mm 8 W 0.5 W A1 BAT 0.1 A 0.9 80 C -5... 0 C x 18 W PCA x1/ EXCE oneall lp Y II 185 0 x 0 x 1 mm 50 mm W 8.0 W A1 BAT 0. A 0.9 80 C -5... 5 C x W PCA x1/ EXCE oneall lp Y II 185 0 x 0 x 1 mm 50 mm 5 W 9.5 W A1 BAT 0. A 0.98 80 C -5... 5 C x W PCA x1/ EXCE oneall lp Y II 185 0 x 0 x 1 mm 50 mm W 9.0 W A1 BAT 0.1 A 0.98 80 C -5... 5 C x 1 W PCA x1/9 EXCE oneall lp Y II 185111 0 x 0 x 1 mm 50 mm 1 W 5.5 W A1 BAT 0.1 A 0.9 85 C -5... 0 C x W PCA x1/9 EXCE oneall lp Y II 185111 0 x 0 x 1 mm 50 mm W 1.0 W A1 BAT 0.1 A 0.98 85 C -5... 5 C x 9 W PCA x1/9 EXCE oneall lp Y II 185111 0 x 0 x 1 mm 50 mm W 8.0 W A1 BAT 0. A 0.98 85 C -5... 5 C x 0 W PCA x1/9 EXCE oneall lp Y II 185111 0 x 0 x 1 mm 50 mm 80 W 8.0 W A1 BAT 0.0 A 0.99 85 C -5... 5 C x 8 W PCA x8/5 EXCE oneall lp Y II 1859 5 x 0 x 1 mm mm 5 W 0.5 W A1 BAT 0.8 A 0.9 80 C -5... 0 C x 5 W PCA x8/5 EXCE oneall lp Y II 1859 5 x 0 x 1 mm mm 8 W 11.5 W A1 BAT 0.51 A 0.99 85 C -5... 55 C x 5 W PCA x5/9 EXCE oneall lp Y II 185 0 x 0 x 1 mm 50 mm 0 W.5 W A1 BAT 0. A 0.9 80 C -5... 5 C x 9 W PCA x5/9 EXCE oneall lp Y II 185 0 x 0 x 1 mm 50 mm 98 W 5.5 W A1 BAT 0.9 A 0.98 85 C -5... 0 C x 55 W PCA x80 EXCE oneall lp Y II 185 5 x 0 x 1 nm mm 1 W 11.0 W A1 BAT 0.5 A 0.99 80 C -5... 55 C x 80 W PCA x80 EXCE oneall lp Y II 185 5 x 0 x 1 nm mm W 1.0 W A1 BAT 0. A 0.99 80 C -5... 55 C 1 According to the EU directives on ecodesign requirements (EC) o. 5/009 and (EC) o. /0. Valid at 0 % dimming level. + C to ta max: unrestricted dimming. -5 C to + C: unrestricted dimming from 0 % to 0 %. -5 C to + C, dimming below 0 %: malfunction possible but no damage to ECG. This applies to AC and DC operation. Data sheet 0/1-FD00-9 www.tridonic.com
F ballasts Standards E 550 E 099 E 00-- E 1-- E Suitable for emergency installations according to E 501 CISPR CISPR IEC 099 IEC 00-- IEC 1-- IEC IEC 8 (according to I standard V1) amp starting characteristics Warm start Starting time 0.5 s with AC Starting time 0. s with DC Start at any dimming level AC operation Mains voltage 0 0 V 50/0 Hz 198 V 50/0 Hz including safety tolerance (± %) 198 5 V 50/0 Hz including performance tolerance (+ % / -8 %) Mains currents in DC operation (at % light output) Mains current at Mains current at Type amp type Wattage Un = 0 VDC Un = 5 VDC PCA 1x1/ EXCE oneall lp Y II 1 x 1 W 0.0 A 0.0 A 1 x W 0.05 A 0.05 A 1 x 1 W 0.05 A 0.0 A PCA 1x1/9 EXCE oneall lp Y II 1 x W 0.0 A 0.0 A 1 x 9 W 0.0 A 0.0 A 1 x 0 W 0.0 A 0.0 A PCA 1x8/5 EXCE oneall lp Y II 1 x 8 W 0.0 A 0.0 A 1 x 5 W 0.11 A 0. A 1 x 5 W 0.0 A 0.0 A 1 x 9 W 0.09 A 0.08 A PCA 1x5/9/80 EXCE oneall lp Y II 1 x 55 W 0.11 A 0. A 1 x 80 W 0.1 A 0.1 A 1 x 80 W 0.1 A 0.1 A x 1 W 0.0 A 0.0 A PCA x1/ EXCE oneall lp Y II x 18 W 0.0 A 0.0 A x W 0. A 0.09 A x W 0.09 A 0.09 A x 1 W 0.08 A 0.0 A PCA x1/9 EXCE oneall lp Y II x W 0.1 A 0.11 A x 9 W 0.1 A 0.1 A x 0 W 0.1 A 0.1 A PCA x8/5 EXCE oneall lp Y II x 8 W 0. A 0. A x 5 W 0.0 A 0.18 A PCA x5/9 EXCE oneall lp Y II x 5 W 0.1 A 0.11 A x 9 W 0.1 A 0. A PCA x80 EXCE oneall lp Y II x 55 W 0.0 A 0.19 A x 80 W 0. A 0.5 A DC operation 0 0 V 0 Hz 198 5 V 0 Hz certain lamp start 1 80 V 0 Hz operating range Use in emergency lighting installations according to E 501 or for emergency luminaires according to E 1-- appendix J. Mains current for defective or missing lamps at DC operation < 5 ma. ight output level in DC operation Programmable from 1 % to 0 % Programming by extended DSI or I signal (1 bit). Default value is % In DC operation dimming mode can be activated. Emergency units The PCA EXCE oneall lp y II ballasts are compatible with all emergency units from Tridonic. See the table in the data sheet. Also all 5-pole emergency units can be used. When used with other emergency units tests are necessary. Temperature range Unlimited dimming range from C to ta max. -5 C to C: dimming operation from 0 % to 0 %. If dimm level goes below 0 % malfunction possible, but no electronic ballast damage. This applies to AC and DC operation. Ballast lumen factor AC operation (AC-BF) E 099 8.1 Type amp type Wattage AC-BF at U = 0 VAC PCA 1x1/ EXCE oneall lp Y II 1 x 1 W 1.00 1 x W 1.01 1 x 1 W 0.99 PCA 1x1/9 EXCE oneall lp Y II 1 x W 0.9 1 x 9 W 1.01 1 x 0 W 1.05 PCA 1x8/5 EXCE oneall lp Y II 1 x 8 W 0.98 1 x 5 W 1.0 1 x 5 W 1.00 1 x 9 W 1.00 PCA 1x5/9/80 EXCE oneall lp Y II 1 x 55 W 1.0 1 x 80 W 1.0 1 x 80 W 1.0 x 1 W 1.01 PCA x1/ EXCE oneall lp Y II x 18 W 0.90 x W 1.00 x W 0.98 x 1 W 0.9 PCA x1/9 EXCE oneall lp Y II x W 0.9 x 9 W 0.98 x 0 W 1.05 PCA x8/5 EXCE oneall lp Y II x 8 W 1.00 x 5 W 1.00 PCA x5/9 EXCE oneall lp Y II x 5 W 1.01 x 9 W 1.0 PCA x80 EXCE oneall lp Y II x 55 W 1.0 x 80 W 1.0 The ballast lumen factor for AC operation (AC-BF) does not alter from Un = 198 V AC to Un = 5 V AC. The ballast lumen factor for DC operation (DC-BF) on the basis of an automatic power reduction of the ballasts (default value is %) will be smaller than AC. It does not alter in the DC operating range (198 V DC). Data sheet 0/1-FD00-9 www.tridonic.com
F ballasts Dimming Dimming curve is adapted to the eye sensitiveness. Dimming range 1 % to 0 % Digital control with: DSI signal: 8 bit Manchester Code Speed 1 % to 0 % in 1. s I signal: 1 bit Manchester Code Maximum speed 1 % to 0 % in 550 ms (adjustable between 0 ms and 90 s) Programmable parameter: Minimum dimming level Maximum dimming level Default minimum = 1 % Default maximum = 0 % Control input (/D1, /D) Digital I/DSI signal or a push-to-make switch (switchdim) or a motion detector (corridorfuctio) can be wired on the same terminals (/D1 and / D). Digital signal I/DSI The control input is non-polar and protected against accidental connection with a mains voltage up to V. The control signal is not SEV. Control cable has to be installed in accordance to the requirements of low voltage installations. Different functions depending on each module. SMART interface An additional interface for the direct connection of the SMART-Sensoren or SMART-Plugs. For precise instructions relating to the available sensors and plugs and for a description of how they work in connection with the PCA devices please see the separate documentation for PCA xitec II. The equipment must be installed in accordance with the relevant directives on low voltage. Ensure that power to the ballast is switched off before connecting or disconnecting the sensors and plugs. switchdim Integrated switchdim function allows a direct connection of a push to make switch for dimming and switching. Brief push (< 0. s) switches ballast O and OFF. The ballasts switch-o at light level set at switch-off. After switch O the last settet dimming level will be activated again. When the push to make switch is held, PCA ballasts are dimmed. After repush the PCA is dimmed in the opposite direction. The switchdim fade time is set to s from min. to max. in the factory settings. With a 0 s push to the push to make switch this fade time can be changed to s. In this instance the switchdim application will be synchronized to 50 % light level after s and after 0 s the light level rises to 0 % with the new fade time. At every synchronizsation ( s keystroke) the device will reset to s (factory setting) In installations with PCAs with different dimming levels or opposite dimming directions (e.g. after a system extension), all PCAs can be synchronized to 50 % dimming level by a s push. Use of push to make switch with indicator lamp is not permitted. switchdim and corridorfuctio are very simple tools for controlling ballasts with conventional momentaryaction switches or motion sensors. To ensure correct Dimming characteristics PCA EXCE oneall lp Y II digital dimming value 55 5 00 I DSI 0 0 5 50 5 0 0 0 0 0 50 0 0 80 90 0 relative lighting level in % Dimming characteristics as seen by the human eye operation a sinusoidal mains voltage with a frequency of 50 Hz or 0 Hz is required at the control input. Special attention must be paid to achieving clear zero crossings. Serious mains faults may impair the operation of switchdim and corridorfuctio. corridorfuctio To activate the corridorfuctio a voltage of 0 V simply has to be applied for five minutes at switchdim connection. The unit will then switch automatically to the corridorfuctio. ote: If the corridorfuctio is wrongly activated in a switchdim system (for example a switch is used instead of pushbutton), there is the option of installing a pushbutton and deactivating the corridorfuctio mode by five short pushes of the button within three seconds. The corridorfuctio offers the added benefit of a second and third preprogrammed profile, which can be activated by the SMART-Plugs. It is also possible to combine the corridorfuctio with the SMART-Sensor 5D 19f light sensor. Application and functionallity of profiles see user manual of the corridorfuctio. Energy saving PCA EXCE oneall lp Y II mains power in % 0 90 80 0 0 50 0 0 0 0 0 90 80 0 0 50 0 0 0 5 1 dimming level in % switchdim PCA EXCE oneall lp Y II DSI D1 D D1 D DSI PCA EXCE oneall lp Y II I D1 D corridorfuctio PCA EXCE oneall lp Y II I PCA EXCE oneall lp Y II Data sheet 0/1-FD00-9 www.tridonic.com
F ballasts oading of automatic circuit breakers (imitation via inrush current) Automatic circuit breaker type C C1 C1 C0 B B1 B1 B0 Inrush current (1.5 mm ) Inrush current (.5 mm ) Installation Ø 1.5 mm 1.5 mm 1.5 mm.5 mm 1.5 mm 1.5 mm 1.5 mm.5 mm I max time I max time PCA 1x1/ EXCE oneall lp Y II 50 80 0 180 5 0 5 90 19. A 1 µs 19. A 1 µs PCA 1x1/9 EXCE oneall lp Y II 50 8 1 5 8 5. A 190 µs 5.1 A 19 µs PCA 1x8/5 EXCE oneall lp Y II 5 11 1. A 5 µs 8.5 A µs PCA 1x5/9/80 EXCE oneall lp Y II 1 8 8 11 1 1 1. A 1 µs 1. A µs PCA x1/ EXCE oneall lp Y II 50 11 1 5 8.1 A µs 8. A µs PCA x1/9 EXCE oneall lp Y II 1 8 8 11 1 1. A 0 µs 8.8 A 0 µs PCA x8/5 EXCE oneall lp Y II 1 0 8 11 18 8.9 A 88 µs 0. A 8 µs PCA x5/9 EXCE oneall lp Y II 1 0 8 11 1.0 A 1 µs.9 A 0 µs PCA x80 EXCE oneall lp Y II 8 1 18 0 9 8. A 1 µs 50.1 A 58 µs Continuous operation: to calculate the protective saftey switch see main current, page Intelligent Voltage Guard Intelligent Voltage Guard is the name of the electronic monitor from Tridonic. This inno vative feature of the PCA family of control gear from Tridonic immediately shows if the mains voltage rises above certain thresholds. Measures can then be taken quickly to prevent damage to the control gear. If the mains voltage rises above approx. 18 Vrms (voltage depends on the ballast type), the lamp starts flashing on and off. To avoid a damage of the device the mains supply has to be switched off at this signal. Intelligent Temperature Guard The intelligent temperature guard protects the PCA EXCE oneall lp y II from thermal overheating by reducing the output power or switching off in case of operation above the thermal limits of the luminaire or ballast. Depending on the luminaire design, the ITG operates at about 5 to C above tc temperature. Data sheet 0/1-FD00-9 www.tridonic.com 5
F ballasts Harmonic distortion in the mains supply (at 0 V / 50 Hz) Type amp type Wattage THD 5 9 11 PCA 1x1/ EXCE oneall lp Y II 1 x 1 W 9 1 1 1 x W 9 1 1 1 x 1 W 9 PCA 1x1/9 EXCE oneall lp Y II 1 x W 8 1 1 1 1 x 9 W 1 1 1 1 x 0 W 1 1 1 1 PCA 1x8/5 EXCE oneall lp Y II 1 x 8 W 1 x 5 W 1 1 1 1 1 x 5 W 1 x 9 W 8 PCA 1x5/9/80 EXCE oneall lp Y II 1 x 55 W 5 1 1 1 1 x 80 W 5 1 1 1 1 1 x 80 W 5 1 1 1 1 x 1 W 8 1 1 1 PCA x1/ EXCE oneall lp Y II x 18 W 1 1 1 x W 5 1 1 1 1 x W 1 1 1 1 x 1 W PCA x1/9 EXCE oneall lp Y II x W 1 1 1 x 9 W 1 1 1 1 x 0 W 1 1 1 1 PCA x8/5 EXCE oneall lp Y II x 8 W x 5 W 8 1 1 1 1 PCA x5/9 EXCE oneall lp Y II x 5 W 9 5 1 1 x 9 W 1 1 1 1 PCA x80 EXCE oneall lp Y II x 55 W 1 1 1 x 80 W 5 1 1 1 Operating voltage Type amp type Wattage Uout PCA 1x1/ EXCE oneall lp Y II PCA 1x1/9 EXCE oneall lp Y II PCA 1x8/5 EXCE oneall lp Y II PCA 1x5/9/80 EXCE oneall lp Y II PCA x1/ EXCE oneall lp Y II PCA x1/9 EXCE oneall lp Y II PCA x8/5 EXCE oneall lp Y II PCA x5/9 EXCE oneall lp Y II PCA x80 EXCE oneall lp Y II 1 x 1 W 0 V 1 x W 0 V 1 x 1 W 0 V 1 x W 0 V 1 x 9 W 0 V 1 x 0 W 0 V 1 x 8 W 0 V 1 x 5 W 0 V 1 x 5 W 0 V 1 x 9 W 0 V 1 x 55 W 0 V 1 x 80 W 0 V 1 x 80 W 0 V x 1 W 0 V x 18 W 0 V x W 0 V x W 0 V x 1 W 0 V x W 0 V x 9 W 0 V x 0 W 0 V x 8 W 0 V x 5 W 0 V x 5 W 0 V x 9 W 0 V x 55 W 0 V x 80 W 0 V Data sheet 0/1-FD00-9 www.tridonic.com
F ballasts Humidity: 5 % up to max. 85 %, not condensed (max. 5 days/year at 85 %) Storage temperature: -0 C up to max. +80 C The devices have to be within the specified temperature range (ta) before they can be operated. Expected life-time Type amp type Wattage ta = 0 C ta = 50 C ta = 0 C PCA 1x1/ EXCE oneall lp Y II PCA 1x1/9 EXCE oneall lp Y II PCA 1x8/5 EXCE oneall lp Y II PCA 1x5/9/80 EXCE oneall lp Y II PCA x1/ EXCE oneall lp Y II PCA x1/9 EXCE oneall lp Y II PCA x8/5 EXCE oneall lp Y II PCA x5/9 EXCE oneall lp Y II PCA x80 EXCE oneall lp Y II x = not permitted 1 x 1 W 1 x W 1 x 1 W 1 x W 1 x 9 W 1 x 0 W 1 x 8 W 1 x 5 W 1 x 5 W 1 x 9 W 1 x 55 W 1 x 80 W 1 x 80 W x 1 W x 18 W x W x W x 1 W x W x 9 W x 0 W x 8 W x 5 W x 5 W x 9 W x 55 W x 80 W tc 50 C 0 C 0 C tc 50 C 0 C 0 C tc 50 C 0 C 0 C ife-time > 0,000 h > 0,000 h 90,000 h tc 55 C 0 C 0 C tc 5 C 0 C 80 C ife-time > 0,000 h > 0,000 h 50,000 h tc 5 C 0 C 80 C ife-time > 0,000 h > 0,000 h 50,000 h tc 5 C 0 C 80 C ife-time > 0,000 h > 0,000 h 50,000 h tc 50 C 0 C 0 C ife-time > 0,000 h > 0,000 h 90,000 h ife-time > 0,000 h > 0,000 h 90,000 h ife-time > 0,000 h > 0,000 h 90,000 h tc 0 C 0 C 80 C ife-time > 0.000 h > 0.000 h 90.000 h tc 0 C 0 C 80 C ife-time > 0.000 h > 0.000 h 0.000 h tc 0 C 0 C 80 C ife-time > 0.000 h > 0.000 h 80.000 h tc 55 C 0 C 0 tc 5 C 5 C x ife-time > 0,000 h 0,000 h x ife-time > 0,000 h > 0,000 h 80,000 h tc 5 C 5 C 80 C ife-time > 0,000 h 80,000 h 50,000 h tc 5 C 5 C x ife-time > 0,000 h 80,000 h x tc 5 C 0 C x ife-time > 0,000 h 80,000 h x Data sheet 0/1-FD00-9 www.tridonic.com
F ballasts Installation instructions Wiring type and cross section The wiring can be solid cable with a cross section of 0.5 to 0.5 mm² for push terminal and 0.5 mm² for IDC terminal. For the push-wire connection you have to strip the insulation (8 9 mm). wire preparation: 0.5 0.5 mm² 8 9 mm oosen wire through twisting and pulling Wiring advice The lead length is dependent on the capacitance of the cable. Ballast Terminal Maximum capacitance allowed Type Cold Hot Cold Hot PCA 1xx EXCE oneall lp Y II 1, 1, 1 00 pf 0 pf PCA xx EXCE oneall lp Y II 1, 1, 1, 11,, 1 00 pf 0 pf With standard solid wire 0.5/0.5 mm² the capacitance of the lead is 0 80 pf/m. This value is influenced by the way the wiring is made. amp connection should be made with symmetrical wiring. Hot leads (, 11,, 1) and cold leads (1, 1, 1) should be separated as much as possible. When using two or more dimmable ballasts in one luminaire with separate dimming controls, the lamp leads must be kept separate. Sensor wires Sensor wires must be routed separately from the lamp wires and mains cables otherwise the lighting control system may malfunction. If separate routing is not possible (for reasons of space) shielded lamp wires and mains cables must be used. Dimmable ballasts from Tridonic have to be earthed. * * control signal / D1 / D 1 1 1 * * control signal /D1 /D 1 1 1 1 11 PCA EXCE oneall lp Y II 1x1 80 W * leads, 1: keep wires short, max. 1.0 m leads 1, 1: max..0 m; ballast must be earthed * * digital signal (DSI), I or switchdim * leads, 11,, 1: keep wires short, max. 1.0 m leads 1, 1, 1: max..0 m; ballast must be earthed * * digital signal (DSI), I or switchdim PCA EXCE oneall lp Y II x1 80 W Dimmable ballasts from Tridonic have to be earthed. RFI Connection to the lamps of the hot leads must be kept as short as possible Mains leads should be kept apart from lamp leads (ideally 5 cm distance) Do not run mains leads adjacent to the electronic ballast Twist the lamp leads Keep the distance of lamp leads from the metal work as large as possible Mains wiring to be twisted when through wiring Keep the mains leads inside the luminaire as short as possible General advise Electronic ballasts are virtually noise free. Magnetic fields generated during the ignition cycle can cause some background noise but only for a few milliseconds. Operation on DC voltage Our ballasts are construed to operate DC voltage and pulsed DC voltage. To operate ballasts with pulsed DC voltage the polarity is absolute mandatory. Isolation and electric strength testing of luminaires Electronic devices can be damaged by high voltage. This has to be considered during the routine testing of the luminaires in production. According to IEC 0598-1 Annex Q (informative only!) or EEC 0-Annex A, each luminaire should be submitted to an isolation test with 500 VDC for 1 second. This test voltage should be connected between the interconnected phase and neutral terminals and the earth terminal. The isolation resistance must be at least MΩ. As an alternative, IEC 0598-1 Annex Q describes a test of the electrical strength with 00 VAC (or 1.1 x 00 VDC). To avoid damage to the electronic devices this test must not be conducted. Glow-wire test according to E 0598-1 50 C, 50 C and 850 C passed Programming With appropriate software and a USB interface different functions can be activated and various parameters can be configured in the new PCA TC EXCE oneall lp y II. All that is needed is a I-USB and the software. Master Configurator For programming the corridorfuctio, device configuration (fade time, epoweronevel, etc.) DC level, compatibility settings, and startup date and for resetting. Maximum amount of ballast see I/DSI specification. PE I PS USB SCI PE PE 1 1 1 1 11 1 1 1 1 11 + 1 PC and the SW-Tool Master Configurator max. ECG s (I) /D1 /D 5 PE 1 1 1 1 11 For further technical information please visit www.tridonic.com Data sheet 0/1-FD00-9 www.tridonic.com 8