Direct readout of ion concentration at breakthrough pricing!

Simple to use preprogrammed calibration points allow even beginners to take readings in minutes! Ion/mV and Ion/mV/pH/ corn Ion 5 & Ion 6 Meters Direct readout of ion concentration at breakthrough pricing! year warranty 3 meter only ISO 9001 v e n d o r ERTIFIED ph Measurement Works with almost all Ion Selective Electrodes ±500 mv ranges covers the vast majority of ISEs ompact size fits right in your pocket take your OKTON Ion meter anywhere! mv measurement mode allows you to check performance and calibration of your ion selective electrode ll push button operation for fast, easy use no trimpots to adjust! Hold function freezes measurements for convenient reading and recording uto-off function turns off meter after 17 minutes of non-use to save batteries Optional protective boot helps shield your meter from drops and dings and features a built-in stand ISE labware kit available contains volumetric flasks and pipettes for making serial dilutions The ION 6 meter also features: ph and temperature ( ) readout with high ±0.01 ph/±0.5 accuracy utomatic Temperature ompensation (T) for the highest accuracy in changing temperature conditions Use with most ph electrodes with BN connectors bove: corn ION 5 meter shown actual size. Top right: corn ION 6 meter comes with T temperature probe; customize with the electrode best for your application. Middle right: ION 5 shown with optional rubber boot. Lower right: ISE labware kit contains the glassware you need for making serial dilutions. pricing breakthrough in direct ion concentration measurements! The compact and rugged corn Ion meters are the most economical ion meters with direct concentration readings available. hoose between the Ion 5 or Ion 6 meters the Ion 6 meter also takes readings in ph and temperature ( ). The Ion 5 and Ion 6 meters offer easy access connections for probes. The splash-resistant membrane keypad helps protect meter components from occasional spills. The large LD gives you a clear reading at a glance, and warns you of low-battery conditions or calibration errors. Use our ISE labware kit for making serial dilutions; this kit contains all the volumetric flasks and pipettes you'll need. Order the optional rubber boot to protect your meter from drops and dings. See the back of this sheet for ordering information, complete specifications and accessories....setting the standard, again and again

Large ustom LD for clear and easy readings; switch between measured parameters with the touch of a button. Easy access connections for BN electrode and temperature sensor (Ion 6 only). ORN Ion 5 and Ion 6 meters pplications ISE applications: Use this meter with any of 20 types of ISE electrodes to take direct measurements of ion concentration. Titration methods allow measurement of many other types of ions. Water Quality Testing: Use the corn Ion meters for quick fluoride level checks. Environmental/gricultural pplications: Use for checking nutrient levels in aquariums, aquaculture and hydroponics. Educational pplications: These economical, sturdy meters are ideal for quick, accurate checks in labs and schools. Laboratory / Industrial pplications: Use for water hardness testing or other ions in feed or wastewater, sewage treatment, soil testing, fertilizer testing, plant tissue testing, food processing (check sodium, potassium levels), geological testing, and metal plating. lso use in the paper/pulp or pharmaceutical industries. Specifications Model Ion 5 and Ion 6 meters Ion 6 meter only Ion mv ph Temperature Range 0.01 to 1999 ppm 500 to +500 mv 0.00 to 14.00 ph 0.0 to 100.0 0.01 ppm (0.01 to 0.99 ppm); Resolution 0.1 mv within ±199.9 mv 0.1 ppm (0.1 to 199.9 ppm); 1 mv beyond ±200 mv 1 ppm (200 to 1999 ppm) 0.01 ph 0.1 ccuracy ±1% full scale ±0.2 mv within ±199.9 mv ±2 mv beyond ±200 mv ±0.01 ph ±0.5 alibration 2 or 3 points, 0.1; 1; 10; 100 ppm Up to 3 buffer values (ph 4.01; Offset 0.1 not available (minimum 2 points) 7.00; 10.0); auto-buffer recognition increments Splash-resistant membrane keypad helps protect components. Optional rubber boot offers sturdy protection for meter; acts as meter stand for benchtop use. ISE labware kit contains volumetric flasks and pipettes for serial dilutions. Minimum slope during ion calibration: 40 mv/decade for monovalent ions; 20 mv/decade for divalent ions Operating Temperature: 0 to 50 (32 to 122 F) ph slope range (Ion 6 only): 80% to 120% Temperature ompensation (Ion 6 only): Manual or utomatic Temperature ompensation (T) from 0.0 to 100.0 Ordering Information ORN Ion Meters ll meters include operating instructions and batteries. Shipping weight: 1.0 lb (450 g) WD-35613-21 Ion 5 meter, meter only; electrode not included WD-35613-31 Ion 6 meter, meter and temperature probe; electrode not included WD-35613-30 Ion 6 meter, includes ph electrode and temperature probe WD-35613-33 Ion 6 meter, includes ll-in-one combination ph electrode/temperature sensor ISE Electrodes These electrodes include 15 ml of reference electrolyte and a filling pipette. Each ISE is epoxy body, double junction (except WD-35802-00 is single junction) and have BN connector. Shpg wt: 0.5 lb (230 g). WD-35802-00 mmonia (NH 3 ) electrode WD-35812-02 mmonium (NH 4+ ) electrode WD-35812-08 alcium (a +2 ) electrode WD-35812-12 hloride (l ) electrode WD-35812-14 opper (u +2 ) electrode WD-35812-18 Fluoride (F ) electrode WD-35812-24 Lead (Pb +2 ) electrode WD-35812-30 Nitrate (NO 3 ) electrode WD-35812-42 Sodium (Na + ) electrode WD-35812-48 Water Hardness electrode ISE Solution Kits These kits contain the solutions and accessories necessary for calibration and sample preparation. Shpg wt 1 lb (460 g). WD-35802-50 mmonia (NH 3 ) solution kit WD-35802-53 mmonium (NH 4+ ) solution kit WD-35802-59 alcium (a +2 ) solution kit WD-35802-63 hloride (l ) solution kit WD-35802-65 opper (u +2 ) solution kit WD-35802-69 Fluoride (F ) solution kit WD-35802-75 Lead (Pb +2 ) solution kit Power: 4 x 1.5 V batteries >200 hours continuous use (included) Dimensions: Meter: 5.5" x 2.7" x 1.3" (14 x 7 x 3.5 cm) Boxed: 9.25 x 6.5" x 3.0" (23.5 x 16.5 x 7.5 cm) Weight: Meter only: 0.9 lb (408 g); Boxed: 1 lb (450 g) WD-35802-79 Nitrate (NO 3 ) solution kit WD-35802-93 Sodium (Na + ) solution kit WD-35802-99 Water Hardness solution kit ph Electrodes WD-35801-00 ph electrode, epoxy body, single junction, 5.2"L x 0.47" OD (12 mm) with 3-ft cable. Shpg wt 0.5 lb WD-35805-01 ph electrode, epoxy body, double junction, 5.2"L x 0.47" OD (12 mm) with 3-ft cable.. Shpg wt 0.5 lb WD-35613-05 Replacement temperature probe, 316 SS, 3-ft cable, polypropylene cap. Shpg wt 0.15 lb alibration Solutions and ccessories ISE Labware Kit, includes one 10 ml graduated pipette and bulb, one 10 ml graduated cylinder, and three 250 ml beakers. Ideal for standard and sample preparation. WD-35613-60 ISE Labware kit WD-35606-80 Protective rubber boot for corn Series meters. Shpg wt 0.5 lb (0.23 kg) SINGLES ph alibration Pouches, box of 20. Each airtight pouch contains 20 ml of fresh, premixed ph buffer or rinse water. ccuracy ±0.01 ph at 25. Shpg wt 1 lb (0.45 kg) WD-35653-01 ph 4.01 calibration pouches WD-35653-02 ph 7.00 calibration pouches WD-35653-03 ph 10.00 calibration pouches WD-35653-00 Rinse water pouches WD-35653-04 ssortment pack; five each of ph 4.01, 7.00, 10.00, and rinse water pouches ph alibration Buffer Bottles, one pint premixed calibration solution. ccuracy ±0.01 ph at 25. Shpg wt 1.1 lbs (0.5 kg) WD-00654-00 ph 4.01 buffer WD-00654-04 ph 7.00 buffer WD-00654-08 ph 10.00 buffer ORDER FROM Bulletin ph B2 R1 Printed in the U.S.. 8/01 OKTON TM Reg. #1,692,543. We reserve the right to make changes, improvements and modifications to products shown. ll prices subject to change without notice. OKTON Instruments are available only through authorized OKTON distributors.

10. Warranty OKTON warrants this meter to be free from significant deviations in material and workmanship for a period of three years from date of purchase. If repair or adjustment is necessary and has not been the result of abuse or misuse within the warrantied time period, please return freight prepaid and correction will be made without charge. OKTON alone will determine if the product problem is due to deviations or customer misuse. Out-of-warranty products will be repaired on a charge basis. 11. Return of items uthorization must be obtained from your OKTON distributor before returning items for any reason. When applying for authorization, please include data regarding the reason the items are to be returned. For your protection, items must be carefully packed to prevent damage in shipment and insured against possible damage or loss. We will not be responsible for damage resulting from careless or insufficient packing. restocking charge will be made on all unauthorized returns. NOTE: We reserve the right to make improvements in design, construction, and appearance of products without notice. OPERTING INSTRUTIONS OKTON WD-35613-21, -30, -31, -33 ION 5 and ION 6 corn Series Meters ph/ion/ Meter ION 6 corn series DISTRIBUTED BY: ON OFF L HOLD ENTER MODE 00702-79 Printed in the U.S.. 8/99

Table of ontents 1. Introduction...4 2. Display and keypad functions...5 3. Preparation...6-7 3.1 Inserting the batteries...6 3.2 onnecting the electrode...6 3.3 Switching the meter on...7 4. alibration...8-13 4.1 Ion calibration...8-9 4.2 ph buffer set selection...10 4.3 ph calibration...11-12 4.4 Temperature calibration...12 4.5 Resetting the meter to factory calibration values...13 5. Measurement...14-15 5.1 Measuring ion concentration...14 5.2 Measuring mv...14 5.3 Measuring ph and temperature...15 5.4 Measuring ph with manual temperature compensation...15 5.5 HOLD feature...15 6. Electrode care and maintenance...16 6.1 Ion selective electrode care...16 6.2 ph electrode care...16 7. Troubleshooting...17 8. Specifications...18 9. ccessories...19-20 10. Warranty...back cover 11. Return of items...back cover ppendix. Temperature curve selection...21 2 3

1. Introduction Thank you for purchasing an OKTON ION corn Meter. These economical, microprocessor-based meters measure the ion concentration of various ions (mono and divalent). The corn ION meters feature: Large LD for clear and easy reading ION 5 meter allows ion and mv measurement ION 6 series meters allows ion, ph, mv, and temperature ( ) measurement This instruction manual is organized for easy reference. For basic functions of this meter, read sections 2 through 5. These sections include basic instructions that will get you up and running quickly. The remaining sections of this manual (6 through 11) deal with electrode maintenance, error messages and troubleshooting. This part of the manual also includes the Specifications, ccessories, Warranty and Return of Items section. 2. Display and Keypad Functions The corn has a large custom LD with the following indicators: indicates HOLD function is activated indicates low battery condition HO LO Reading ph mv indicates operation mode* mv annunciator ph annunciator (ION 6 only) Degree annunciator (ION 6 only) *No unit annunciator is displayed when in ion concentration mode The OKTON corn meter has six keys on its splashproof keypad. These keys are ON/OFF, L, HOLD/ENTER, (UP), (DOWN) and MODE. ON/OFF: Powers meter on and shuts unit off. Meter directly enters measurement mode when you turn it on. L ON OFF HOLD ENTER L: llows calibration of the meter for Ion, ph, and Temperature HOLD/ENTER: Freezes the measured reading; confirms calibration value. (UP) and (DOWN): Scrolls up or down to the values you want for calibration. MODE: Selects the parameter of measurement: Ion, mv, ph (ION 6 series only) and temperature (ION 6 series only). MODE 4 5

3. Preparation Inserting the batteries 3.1 The battery compartment is found at the back of the instrument. To open the battery compartment, push the lid up. See figure Note the polarity of battery before inserting the batteries into position. fter replacement, place the cover back into its position and press down until it locks tight. "LO" annunciator in the LD alerts you when battery power is running low. Replace batteries with a fresh set as soon as possible. 3.3 Switching the meter on Press the ON/OFF key to power up your meter. ll the LD segments display for a few seconds as the meter goes through a self-diagnostic test. The LD then switches into ion measurement mode. If the LD then displays "Ur", the electrode and/ or temperature sensor may be faulty, or there may be an open circuit. See figure See page 17 for more troubleshooting information. 3.2 onnecting your Electrode To connect the corn meter to your electrode, align the post of the meter's connector with the slots on the electrode's connector, push together and twist the electrode connector 1/2 turn until it clicks into place. To remove, simply rotate the connector counter-clockwise until it unlocks, and slide the connector off the socket. ION 6 meter only: Insert the phono jack of the temperature sensor into the socket on the meter. Unplug the phono jack when not in use. electrode and temperature probe connections at top of corn meter 6 7

4. alibration Ion calibration 4.1 This instrument is capable of up to three-point ion calibration. alibration values are 0.1, 1.0, 10.0 or 100.0. You must calibrate to at least two points. ll calibration points should be one decade apart. For example you may perform three point calibration to 0.1, 1.0 and 10.0, or two point calibration to 10.0 and 100.0. Do NOT perform twopoint calibration to 1.0 and 100.0 (meter will display Er4 ). For best accuracy, calibrate your meter to points with similar concentrations to the solutions you want to test. Before you begin calibration, you must know whether the ion you are measuring is mono or divalent. If you are uncertain, consult your ISE electrode manual, or your OKTON distributor. 1. Prepare at least two calibration standards in accordance with the electrode instructions or your approved methods. For best results, make sure standards and samples are at the same temperature 2. Turn meter on. The ION 5 meter will automatically enter the ion measurement mode. See figure 3. Dip electrode into the first calibration standard. Make sure to start with the calibration standard that has the lowest concentration and move up to the standards that have higher concentrations. B 4. Press L key to enter calibration mode. The display will show 1. See figure B If you are measuring monovalent ions, press ENTER to begin calibration. If you are measuring divalent ions, press MODE. The display will show 2. Press ENTER to begin calibration See figure 5. The first calibration point to appear is 0.1 ppm. If you do NOT wish to calibrate to this point, press (up arrow) to skip, and continue on to the next calibration point. 6. If you DO wish to calibrate to this point, press the ENTER key. The meter will display the mv output of your electrode in the standard solution. llow the instrument to stabilize. Stabilization may take a few minutes depending on electrode and standard concentration. Electrode response in low concentrations is much slower than response in high concentrations. 7. Press ENTER to confirm your calibration. The meter will move on to the next standard (1.0 ppm). 8. Follow steps 5-7 for each of the next calibration points. Make sure to rinse off the electrode with deionized water before placing it in the next calibration standard. 9. fter you have entered three calibration D points, the meter will display the average electrode slope in mv. See figure D You may compare this reading with the mv expected slope value for your electrode from your electrode manual to verify electrode operation. E If you are only calibrating to two points, you will need to press the (up arrow) key until the slope is displayed. If you want to leave the calibration mode for any reason, press the L key to exit the calibration mode. The meter will revert back to the earlier calibration curve. You must calibrate to at least two points in order for calibration to take effect. If you only confirm the one calibration point, the meter will display Er2 when you exit calibration mode, and the meter will revert back to the earlier calibration curve. See figure E 8 9

4.2 ph buffer set selection (ION 6 meter only) The ION 6 meter is capable of up to three-point ph calibration to ensure accuracy across the entire range of the meter. The ION 6 meter can be set to recognize either of two buffer sets: US or NIST buffers. US US : 4.01; 7.00 and 10.01 NIST nst : 4.01, 6.86, and 9.18 To choose your buffer set: 1. Turn meter OFF. Meter must be OFF in order to access buffer selection. 2. While holding down the MODE key, press the ON/OFF key momentarily. ontinue to hold the MODE key until the display flashes buf. B See figure 3. Press the ENTER key to enter buffer set selection mode. The display will flash US See figure B 4. Press the MODE key to toggle between the available buffer sets. The display will flash US or nst as you toggle between the sets 5. Press ENTER key to confirm the buffer set you wish to use. Proceed with calibration in section 4.3 4.3 ph calibration (ION 6 meter only) We recommend you perform at least a 2-point calibration at room temperature using standard buffers that bracket (one above and one below) the expected sample range. You can also perform a 1-point calibration, but make sure that the buffer value is close to the sample value you are measuring. ll new calibrations will over-ride existing data. NOTE: Do not reuse buffer solutions after calibration. ontaminants in the solution can affect the calibration, and the accuracy of the measurements. Before use: remove the electrode soaker bottle. If the electrode has been stored dry, condition the glass bulb by soaking it in tap water for 30 minutes. This hydrates the glass bulb if the electrode is too dry, or has not been used for a long period of time. 1. Turn meter on. Meter will automatically enter ion measurement mode. Press the MODE key until display shows ph in the upper right corner. 2. Rinse electrode thoroughly with deionized water or a rinse solution. DO NOT wipe the electrode; this causes a build-up of electrostatic charge on the glass surface. 3. Dip both the electrode and temperature sensor into ph 7.00 (or 6.86 in NIST set) buffer solution. The glass bulb must be completely immersed into the sample. Stir gently, and wait for reading to stabilize (approximately 40 seconds). 4. Press L key to enter the calibration mode. The display will momentarily flash to indicate libration. See figure The display will then show the current noncalibrated reading, blinking while in calibration mode. See figure B 5. llow the reading to stabilize. The meter automatically recognizes 7.00, 4.01 or 10.00 buffers (or 4.01; 6.86 and 9.18 in NIST set). 6. Press ENTER key once to confirm calibration. B The LD displays O to indicate the calibration point has been confirmed. The meter exits calibration mode and returns ph to measurement mode. 7. Repeat with ph buffers 4.01 and/or 10.00 ( or 6.86/9.18) for best accuracy. 10 11

NOTE: This meter has automatic buffer recognition which identifies the correct ph buffer values during calibration. If buffers other than 4.01, 7.00 or 10.00 are used, or the electrode has worn out, the LD will flash "Er1". See figure Press L key to clear. 4.4 Temperature calibration (ION 6 meter only) The temperature sensor included with your meter is factory calibrated. Over time, the temperature calibration may drift and require recalibration. If you replace the probe you should calibrate temperature prior to ph calibration. 1. onnect your temperature probe to the meter. 2. Press the MODE key until " " appears in the LD. 3. ompare displayed value to a NIST certified thermometer or other thermometer known to be accurate. For best accuracy, place probe and thermometer in a constant temperature bath. 4. Press the L key. The LD shows "" and the reading flashes. B See figures B 5. Use the and keys to adjust the temperature shown to match the accurate temperature (maximum adjustment is ±5 from factory default). 6. Press ENTER key to confirm calibration. The LD displays "O", and the meter then reverts to measurement mode. 4.5 Resetting calibrated values to default values When you calibrate the ph mode of the Ion 6 meter, old ph calibration data is written over on a point by point basis. If when recalibrating you do not calibrate at all three points, the old data may result in errors. You can reset the meter to factory calibration values using the following procedure. 1. TURN METER OFF. Meter must be OFF in order to reset calibration values. 2. Press and hold the L key while switching on the meter using the ON key. Hold the L key until the display shows "rst". 3. Press ENTER key to confirm. The meter automatically clears all stored ph calibration values and reverts to Ion measurement mode. Press MODE key instead of ENTER if you do not wish to reset. Meter will maintain current calibration values and return to the Ion measurement mode. 12 13

5. Measurement Measuring Ion oncentration 5.1 1. Switch on meter. The ION 5 and ION 6 meters will automatically enter the ion measurement mode. No annunciator will appear. See figure 2. Prepare samples as necessary (i.e., add Ionic Strength adjuster). Sample preparation varies depending on ion type see your electrode manual for details on the specific electrode that you are using. 3. Dip electrode into the sample. The sensor or glass bulb of the electrode must be completely immersed into the sample. For best results, use a magnetic stirrer to ensure a homogenous sample. 4. Wait for reading to stabilize. Note reading. ION TIP: oncentration readings are not temperature compensated. Try to avoid temperature fluctuations in your standards and samples. 5.3 Measuring ph and temperature (ION 6 meter only) The corn ION 6 meter also takes readings in ph and temperature. 1. Rinse both electrode and temperature sensor with distilled water. 2. Turn meter on. ION 6 meter automatically enters ion measurement mode. Press MODE key until meter enters ph measurement mode. ph annunciator will appear in the upper right B corner of the LD. See figure 3. Dip electrode and temperature sensor approximately 1" to 2" into sample. Stir gently and wait for display to stabilize. Note ph reading. 4. Press MODE key to see your temperature reading. annunciator will appear in the lower right corner of the LD. See figure B ph 5.2 Measuring mv The mv mode is provided to allow you to check performance and calibration of your ion selective electrode. To verify electrode operation, check mv reading in calibration standards one decade apart in value (i.e.: 1 ppm; 10 ppm). Use the MODE key to toggle between ion and mv measurement (ION 6 meter MODE key switches between ph, temperature, ion and mv). onsult your electrode manual for expected mv (slope) value. If your actual mv readings are not within expected values as stated in your electrode manual, you may need to recondition or replace your electrode. 5.4 Measuring ph with manual temperature compensation When no temperature probe is connected, the meter will compensate based on a manually entered temperature value. The factory default setting is 25 (no temperature compensation). You can compensate for temperature manually by entering the temperature of your solution using the procedure below. 1. Press the MODE key until shows in the display to enter Temperature mode. 2. heck the temperature of your solution using an NIST-certified thermometer or other thermometer known to be accurate 3. Press L key to enter temperature calibration mode. The display shows momentarily and the displayed reading flashes. Use the and keys to match the displayed value to the temperature of your solution. 4. Press ENTER key. 5. Press MODE key to return to ph measurement mode. 5.5 Hold function To freeze your reading, press the HOLD key once. The LD show "HO" to indicate the HOLD function is activated. See figure Press HOLD key again to deactivate the HOLD function and return to measurement mode. HO 14 15

6. Electrode care and maintenance 6.1 Ion selective electrode care For Ion Selective Electrode care, consult the instruction manual included with your electrode. 6.2 Storage ph electrode care (ION 6 meter only) For best results, keep the ph bulb wet. Store the ph bulb in the electrode soaker bottle filled with electrode storage solution. Or you can store the electrode in a ph 4 buffer with 1/100 part saturated Kl. Other ph buffers are also suitable for storage. NEVER use deionized water for storage. fter measuring 1. Rinse the ph electrode and reference junction in deionized water. 2. Store the electrode as recommended in "Storage" or as recommended by the manufacturer. ph electrode cleaning Because your ph electrode is susceptible to dirt and contamination, clean it every one to three months depending on extent and condition of use. lean the electrode in a mild detergent solution. Wipe the probe with a soft tissue paper. void touching the glass membrane with your fingers. Wash thoroughly in tap water and then in distilled water. Recalibrate your meter after cleaning the electrode. Special leaning Tips Salt deposit: dissolve the deposit by immersing the ph electrode in tap water for ten to fifteen minutes. Then thoroughly rinse with distilled water. Oil/grease film: wash electrode ph bulb gently in detergent solution. Rinse electrode tip with distilled water. logged reference junction: heat a diluted Kl solution for 60-80. Place the sensing part of the ph electrode into the heated solution for about 10 minutes. llow the electrode to cool in some unheated Kl solution. Protein deposits: prepare a 1% pepsin solution in 0.1M of Hl. Set the ph electrode in the solution for five to ten minutes. Rinse the electrode with distilled water. 7. Troubleshooting Problem ause Solution Ur or Or measurement over (Or) or on LD Under (Ur) range. Bad electrode hange electrode Bad temperature hange temperature sensor sensor Er1 flashes Wrong or contaminated Use fresh buffer on LD buffer used during solution: ph 4.01, 7.00, (ION 6 meter only) calibration or 10.00 Bad electrode hange electrode Er2 flashes Ion calibration mode perform ion calibration to on LD exited before completing at least two points two-point calibration Er3 flashes Slope of ion selective Recondition or replace on LD electrode lower than 40 mv/ ion selective electrode decade (mono valence) or 15 mv/decade (di valence) Er4 flashes alibration values more than Recalibrate with standards on LD one decade apart one decade apart LO annunciator Low battery Replace batteries on LD with fresh set No display Batteries not Insert batteries in place Batteries not in Re-insert batteries correct polarity (+ and -) with correct polarity Weak batteries Replace batteries Unstable Electrode not deep Place electrode reading enough in sample deeper in sample Insufficient Fill electrode with reference electrolyte reference electrolyte in electrode (if electrode is refillable); replace electrode. Broken electrode Replace electrode External noises or Remove or switch off induction caused by interfering motor by nearby electric motor Dirty electrode lean electrode Slow response Dirty electrode lean electrode 16 17

18 8. Specifications Mode Ion Temperature mv ph (ION 6 only) Range 0.1 to 1999 ppm 0.00 to -500 to 0.0 to 100 +500 mv 14.00 ph 0.1 ppm from 0.1 mv, Resolution 0.1 ppm-199.9 ppm ±199.9 mv; 0.1 1 ppm from 1 mv outside 0.01 ph 200-1999 ppm this range ±0.2 mv, ccuracy ±0.5% of reading ±0.5 from ±199.9 mv; ±2 mv outside ±0.01 ph this range alibration 2 to 3 points: not up to 3 points 0.1, 1, 10, 100 ppm Offset ±5 available (push button) (minimum 2 pts) Minimum slope during ion calibration: 40 mv/decade for monovalent ions; 15 mv/decade for divalent ions ph slope range: 80% to 120% uto buffer recognition: ph 4.01; 7.00; 10.01 (or 4.01; 6.86; 9.18) Display: Single line LD Inputs: BN, phono jack uto shutoff: after 17 minutes Hold Function indicator: HO Error Message display: Er Low battery indication: LO Temperature ompensation: utomatic (T), 0.0 to 50.0 Operating temperature: 0 to 50 Power: 4 x lkaline batteries (>200 hours) Dimensions: Meter only: 5.5" x 2.7" x 1.3" (14 x 7 x 3.5 cm); Boxed: 9.25" x 6.5" x 3" (23.5 x 16.5 x 7.6 cm) Weight: Meter only: 0.5 lb (210 g); Boxed: 1 lb (420 g) 9. ccessories WD-35613-21 dditional ION 5 Series corn Meter (Ion/mV). Shpg wt. 1 lb (460 g). WD-35613-30 dditional ION 6 Series corn Meter (Ion/pH/mV/ ) with ph electrode and temperature probe. Shpg wt. 1 lb (460 g). WD-35613-31 dditional ION 6 Series corn Meter (Ion/pH/mV/ ). Shpg wt. 1 lb (460 g). WD-35613-33 dditional ION 6 Series corn Meter (Ion/pH/mV/ ) with ll-in- One combination ph electrode/temperature probe. Shpg wt. 1 lb (460 g). WD-35606-80 Protective Rubber Boot, encases meter in sturdy rubber to protect it from drops and dings. lso features meter stand for convenient tabletop use. Shpg wt 0.5 lb (230 g). Ion selective electrodes and solution kits WD-35802-00 mmonia ion selective electrode, includes 15 ml of reference electrolyte and a filling pipette. Shpg wt 0.5 lb (230 g). WD-35812-50 mmonia ion selective solution kit, includes 500 ml Ion Strength djuster, 475 ml calibration standard, 60 ml reference electrolyte, syringe dispenser and 20 replacement sensing membranes. Shpg wt. 1 lb (460 g). WD-35812-02 mmonium ion selective electrode, includes 15 ml of reference electrolyte and a filling pipette. Shpg wt 0.5 lb (230 g). WD-35812-52 mmonium ion selective solution kit, includes 475 ml Ion Strength djuster, 475 ml calibration standard, 60 ml reference electrolyte, and syringe dispenser. Shpg wt. 1 lb (460 g). WD-35812-12 hloride ion selective electrode, includes 15 ml of reference electrolyte and a filling pipette. Shpg wt 0.5 lb (230 g). WD-35812-63 hloride ion selective solution kit, includes 475 ml Ion Strength djuster, 475 ml calibration standard, 60 ml reference electrolyte, syringe dispenser, and sensor polishing strips. Shpg wt. 1 lb (460 g). WD-35812-18 Fluoride ion selective electrode, includes 15 ml of reference electrolyte and a filling pipette. Shpg wt 0.5 lb (230 g). WD-35812-69 Fluoride ion selective solution kit, includes 1 gallon Ion Strength djuster, 475 ml calibration standard, 60 ml reference electrolyte, syringe dispenser, and sensor polishing strips. Shpg wt. 1 lb (460 g). WD-35812-30 Nitrate ion selective electrode, includes 15 ml of reference electrolyte and a filling pipette. Shpg wt 0.5 lb (230 g). WD-35812-79 Nitrate ion selective solution kit, includes 475 ml Ion Strength djuster, 475 ml calibration standard, 60 ml reference electrolyte, and syringe dispenser. Shpg wt. 1 lb (460 g). 19

WD-35812-42 Sodium ion selective electrode, includes 15 ml of reference electrolyte and a filling pipette. Shpg wt 0.5 lb (230 g). WD-35812-93 Sodium ion selective solution kit, includes 475 ml Ion Strength djuster, 475 ml calibration standard, 60 ml reference electrolyte, and syringe dispenser. Shpg wt. 1 lb (460 g). WD-35812-48 Water hardness ion selective electrode, includes 15 ml of reference electrolyte and a filling pipette. Shpg wt 0.5 lb (230 g). WD-35812-99 Water hardness ion selective solution kit, includes 475 ml Ion Strength djuster, 475 ml calibration standard, 60 ml reference electrolyte, and syringe dispenser. Shpg wt. 1 lb (460 g). ph electrodes and accessories WD-35801-00 Replacement electrode, 5.75"L x 0.47 OD (12 mm). Shpg wt. 0.5 lb (230 g). WD-35805-05 Double junction electrode, use with solutions that are dirty, have heavy metal or organic ions. 5.75"L x 0.47 OD (12 mm). Shpg wt. 0.5 lb (230 g). WD-35613-05 Replacement temperature probe, 316 SS, polypropylene cap, 3" cable. Shpg wt 0.15 lb (70g). WD-35805-13 ORP electrode, epoxy body, single junction, 5.75"L x 0.49"OD (12.5 mm). Shpg wt 0.5 lb (230 g). WD-00653-04 Electrode storage solution, 1 pint bottle. Keeps electrode bulb moist for faster, more accurate readings. Shpg wt 1.1 lbs (510 g). WD-00653-06 Electrode cleaning solution, 1 pint bottle. Removes buildup from electrodes and maintains electrode sensitivity. Shpg wt 1.1 lbs/510 g. OKTON ph calibration solutions ±0.01 ph accuracy at 25. Shpg wt 1.1 lb (510 g). WD-00654-00 ph 4.01 calibration buffer, 1 pint. WD-00654-04 ph 7.01 calibration buffer, 1 pint. WD-00654-08 ph 10.01 calibration buffer, 1 pint. OKTON Singles ph calibration solution pouches 20/box. ±0.01 ph accuracy at 25. Shpg wt 1.1 lb (454 g) per box. WD-35653-00 Deionized rinse water solution pouches, WD-35653-01 ph 4.01 Singles buffer solution pouches WD-35653-02 ph 7.00 Singles buffer solution pouches WD-35653-03 ph 10.00 Singles buffer solution pouches WD-35653-04 ssortment pack, 5 ea. deionized water, ph 4.01, ph 7.00, and ph 10.00 solution pouches. NOTE: Remember to check the temperature calibration when replacing the T probe. See section 4.4, "Temperature calibration" (page 12). ppendix : temperature curve selection (Ion 6 meter only) Using the temperature calibration procedure described on page 12 of this manual, you can achieve the ±0.5 accuracy specified for this meter. However, to optimize temperature performance, you may make an offset adjustment of the temperature curve. 1. onnect your temperature probe to the meter. 2. Go to the ph calibration mode by pressing the L key when the unit is in ph measurement mode. 3. ompare displayed value to a NIST certified thermometer or other thermometer known to be accurate. For best accuracy, place probe and thermometer in a constant temperature bath, in this example: 25. 4. Press MODE key. Unit displays the default curve temperature, in this example: 25.9 B See figure 5. Press the MODE key to scroll through the three temperature curves. Find the temperature reading closest to your actual temperature, in this example: 24.8. See figure B 6. Press ENTER key to confirm calibration. The LD flashes "O", the meter then reverts to temperature calibration mode for offset adjustment. See figures D 8. Use the and keys to fine tune the temperature reading to your actual temperature, in this example: 25. 6. Press ENTER key to confirm calibration. The LD displays "O", and the meter then reverts to measurement mode. D 20 21

22 23