产 规 Samples approval sheet Customer name Production name 3mm Model A-U3MUBC12 Part number Date 2011-12-22 Prepared by Checked by Approved by Market Dept. 龙 Confirmed by CUSTOMER CONFIRMATION Checked by Approved by
产 规 Model 页码 Page 图 Outline dimensions Unit Tolerance Die material Lens color Emission color mm 0.2mm RemarkP/N & Model in samples approval sheet can be used to inquireplease provide corresponding P/N& model if customer need.
产 规 Model 页码 Page 电 Photoelectricity Parameter 环 Ambient temperature Item Symbol Test condition Min Type Max Unit Forward voltage Reverse current Luminous intensity VF IF=20mA V IR VR=5V A IV IF=20mA mcd Dominant wavelength d IF=20mA ---- nm Spectrum line half width 1/2 IF=20mA 15%1nm0.05V RemarkThe tolerance of intensity:±15%, The tolerance of wave length:±1nm,the tolerance of forwards voltage: ±0.05V. Only reference for above data when testing. 极 Ambient temperature25 humidityrh60% Item Forward Current Peck forward current Reverse Voltage Symbol Value Unit Remark IF 20 ma --- IFM 75 ma F=1KHZ,(duty cycle)1/10 VRP 15 V --- Power Dissipation Operation temperature Storage temperature Soldering temperature Pm 85 mw --- Tamb -25 +80 --- Tstg -35 +85 ---, 3mm 5S Tsol 320 Wave soldering, 3mm out of physical body, 5S
产 规 Model 页码 Page 电 线图 Typical photoelectricity characteristic curve chart 1.0 Flg.1 relative intensity vs. wavelength 60 Flg.2 Forward current derating curve vs. Ambient temperature 50 40 Relative radiant intensity 0.5 Forward current (ma) 30 20 10 0 wavelength (nm) 0 20 40 60 80 100 Ambient temperature Ta( 50 Flg.3 Forward current vs. Forward voltage 3.0 Flg.4 Relative luminous intensity Vs. Ambient temperature 40 2.5 Forward current (ma) 30 20 10 Relative luminous intensity 2.0 1.5 1.0 0.5 0 1 2 3 4 5 0-40 -20 0 20 40 60 Forward voltage(v) Ambient temperature Ta( 2.0 Flg.5 Relative luminous intensity vs. Forward current Flg.6 Radiation diagram 0 10 20 30 Relative luminous intensity(@20ma) 1.5 1.0 0.5 Relative radiant intensity 1.0 0.9 0.8 0.7 605 620 635 40 50 60 70 80 90 0 10 20 30 40 50 0.5 0.3 0.1 0.2 0.4 0.6 Forward current(ma)
产 规 Model 页码 Page 实验项 Reliability Test Project Description Life test Ambience test Item Life test(room temperature) High temperature store Low temperature store High temperature/ humidity test Cold / Heat strike test Cold and heat cycle test Test criterion Test condition Test time Qty Fail qty JIS7021:B4 Ta=255IF=30mA 1000Hrs 22 0 JIS7021:B10 MIL-STD-202:210A MIL-STD-750:2031 Ta=855 1000Hrs 22 0 JIS7021:B12 Ta= -355 1000Hrs 22 0 JIS7021:B11 MIL-STD-202:103D JIS7021::B4 MIL-STD-202:107D MIL-STD-750:1026 JIS7021:A3 MIL-STD-202:107D MIL-STD-705:105E Ta=855 RH=85% 30min -1051005 5min 5min 5min 5min 5min -352585-35 30min 5min 30min 5min 1000Hrs 22 0 50Cycles 22 0 50Cycles 22 0 Judging criterion: Item Forward Current Reverse Volta e Luminous Intensity Symbol Experiment condition Min. Criteria Max. VF IF=20mA ---- Initial Datex1.1 IR VR=5V ---- 30A IV IF=20mA Initial Datex0.7 ----
产 规 Model 页码 Page 项 Note Led bracket forming method 2 The pin of led can be bent where is at least 2mm out of led colloid. Must use fixture to deform the led bracket Finishing the forming of led bracket must be before soldering Guarantee the gap between two pin of led tallys with LED pads in PCB when forming Manual soldering 30W 330 3 3 The tip temperature of soldering iron don t exceed 330 soldering time don t exceed 3s and soldering position must be 3mm out of led colloid A B Soldering temperature curve chartfigure Afigure B Preheat 图 焊 图 焊
产 规 Model 页码 Page ESD countermeasure LED InGaN Static electricity and high volt can damage ledthe production whose Die material is InGaN must strictly required to prevent ESDMust put on static glove and static filletsoldering tool and the cover of device must connect the ground soldering condition follows the related stating of production specification manual Protecting countermeasure when over current Need add the protecting resistor in circuit in order to avoid damaging led due to big current and voltage fluctuation LED LED installation method 1 Pay attention to the led polarity and avoid installation wrongled can t be close to euthermic componentwork condition should tally with it s specification 2 LED Don t install the LED under the condition of the led pin deformation 3 LED PCB LED The led bracket don t load any pressure when installing the led into PCB or fitting hole 4 LED Must avoid any strike and force on led before the soldering temperature return to room temperature Storage time 1 535 RH60% Led can be stored for a year under the condition: the temperature of 5 35 and humidity of RH60%These production must be re-inspected and tested before use if their storage time exceed a year 2 535RH60% 655 24 If led is exposed in air for a week under the condition: the temperature of 5 35 humidity of RH60%must place the led in the ambience of 65 ±5 for 24 hours and use it in 15 days for best Cleaning 3 Be careful of some chemical results in the led colloid fades and damage when using chemical clean the ledsuch as chloroethylene, acetone etc can use ethanol to wash or soak led but the time don t exceed 3 minutes. (Kinked LED LED The kinked tooling scrape easily the pin of led, where the led bracket is rusting easily, especial expose it in moist air. To decrease the led bracket rust, advise using plated tin led bracket.
产 规 Model 页码 Page Packing (1) Packing material static bag Static bag 150mm 200mm (2)remark (3) Qty/per bag500pcs Can change the qty according to actual status (4) Packing box : RemarkDecide detail packing box according to customer order or actual status